Search Documents

By Benjamin F. Tillson

The hammer drill rightly receives the credit for having made the one-man drill possible, and so many economies seem possible through the proper application of different types of hammer drills to various mining, quarrying, and excavating operations, that an indication of the 'economies effected by the New Jersey Zinc Co. at its Franklin mines may be of pertinent interest. When this company commenced its trials of hammer drills in 1907, these tools had not been developed to one-fourth the capacity and refinement which they have at present. At that time it was frequently stated that such a small tool, drilling holes of less diameter than the reciprocating rock drill, could not drill enough holes in a shift to permit the placing of sufficient explosive to break a tonnage of ore comparable with that produced by the "rock drills;" that the placing of small holes inclined upward, at angles steeper than 40' above the horizontal, could not be expected to produce results equal to the large flat, wet or dry, holes in the breasted back of an overhand stope, and would only shatter the ground so as to make the back unsafe. In spite of these adverse opinions, the hammer drills first showed their superiority over both heavy and light reciprocating drills in raising and in stoping, and then in drifting and quarry work. As a result, all of the reciprocating drills at the Franklin mines were scrapped three years ago, all of the mining work being accomplished with increased efficiency, as shown in detail in this article. With the advent of the hammer drill in this property, it was considered advisable to make comparative tests of all the tools accessible, and it has since been the policy to investigate the merits of any advance of the drilling art in order to get the maximum amount of work from the tools. The necessity of devising some means of standardizing drill tests, and of measuring the consumption of compressed air as well as the drilling speed, was early realized. The common test was to fill a measured air receiver with compressed air at a certain gauge pressure, run the drill until the pressure had dropped to too low a figure, then compute from the time, drop in pressure, and

Jan 1, 1915

By F. A. Penning

A number of highly instrumented free fall tests were performed on an arrestment system for a man cage in a vertical shaft. Tests were conducted in the U.S. Bureau of Mines free fall test tower at the Colorado School of Mines. A single tooth safety dog was used to stop on 4x6-in. Keruing (Phillipine mahogany) wet and dry wood guides. The safety dog had a penetration depth of 1 in., an adjustable width from 1-1/2 to 2-1/4 in., and a tooth angle of 80 deg. Twenty-seven free fall tests were performed covering a range in weights from 3-1/2 to 10-1/2 tons, hoisting velocities from 850 to 1350 feet per minute. Average g loads were measured from a low of 0.6 to a high of 3.4. The electronic instrumentation included piezoelectric and seismic mass accelerometers, strain gages on structural and mechanical elements, load cells in the guides, and distance measuring. Computer analysis was used to correlate with experimental measurements used to calculate stress. A statistical analysis gave no indication that the velocity or area affected the wood crushing stress. The instrumentation revealed a chatter occurring during the stop as shown by the accelerometers, strain gages, and load cells. Additional work is required to analyze this newly discovered phenomenon. The chatter imposes loads much higher than the average g load.

Jan 1, 1980

1. Book review Technology of metal powders- recent developments, edited by L. H. Yaverbaum. New Jersey, Noyes Data Corporation, 1980. 400 pp. (Reviewer: B. K. Loveday) 2. New books The use of microprocessors, by M. Aumiaux. New York, Wiley, 1980. 176 pp. $25,50. Aluminium smelter technology, a pure and applied approach, by K. Grojtheim and B. J. Welch. Diisseldorf, Aluminium-Verlag GmbH (P.O. Box 1207, D-4000, Federal Republic of Germany). 146 pp. DM48. Coal-bridge to the future. New York, Harper & Row, 1980. $35. System modeling and response.. theoretical and experimental approaches, by O. Doebelin. New York, Wiley, 1980. 576 pp. $26. Environmental and climatic impact of coal utilization, edited by J. J. Singh and A. Deepak. New York, Academic Press, 1980. 646 pp. $39,50. Proceedings of the Third European Conference on Mixing, York, England, April 1979, edited by H. S. Stephens and C. A. Stapleton. BHRA Fluid Engineering (Cranfield, Bedford Mk43 OAJ, U.K.), 1980. 2 volumes. 500 pp. $50. Lignite technology, edited by P. Nowacki. New Jersey, Noyes Data Corporation, 1980. 228 pp. $42. The application of rock mechanics to cut-and jill mining. London, Institution of Mining and Metallurgy, 1980. Papers presented at the Fifth International Symposium on Jet Cutting Technology, Hanover, Federal Republic of Germany, June 1980, edited by H. S. Stephens and B. Jawis. BHRA Fluid Engineering (Cranfield, Bedford Mk 43 OAJ, U.K.), 1980. 438 pp. £38. World coal resources.. methods of assessment and results, by G. Fettweis. Amsterdam, Elsevier, 1979. 425 pp. $80,50. Geophysical and geochemical techniques for exploration of hydrocarbons and minerals, edited by M. Sittig. New Jersey, Noyes Data Corporation, 1980. 300 pp. $40. Financial Times mining international year book 1980. Longman Group Ltd (Periodicals and Directories Division, Longman House, Burnt Mill, Harlow, Essex CM20 2JE, England). £24 surface, £34 airmail. National Symposium on the Availability of Strategic Minerals, edited by M. J. Jones. London, Institution of Mining and Metallurgy, 1980. 109 pp. 3. NIM reports Report No. 1941 The recovery of chromite and platinum from the UG-2 Upper Chromitite Layer .of the Bushveld Complex at the Pandora Mine (first published 10th Mar., 1978). Report No. .2012 A mineralogical investigation of borehole cores from the Trompsburg Complex (first published 6th Apr., 1979). Report No. 2038 The leaching of sphalerite in acidic ferric sulphate media in the absence of elemental oxygen. Report No. 2052 An investigation of the impurities in native gold by neutron-activation analysis. Report No. 2056 The mineralogy and geochemistry of the copper, lead, and zinc sulphides of the Otavi Mountainland. Report No. 2058 A n elementary introduction to image analysis - a new field of interest at the National Institute for Metallurgy. Report No. 2059 Distributed computer control of industrial processes. Report No. 2060 The analysis, by atomic-absorption spectrophotometry, of activated charcoal.

Jan 1, 1980

By W. J. Birch, A. Wetherelt

The scaled-distance model for blast vibration analysis is the standard method employed throughout the surface mining and quarrying industries to model Peak Particle Velocity (PPV) data. Although empirical, the method is widely accepted and through the simplicity of its application and ease of graphical verification is set to remain a popular option. The validity of the technique relies principally on the fundamental parametric assumption that blasting data is normally distributed. Throughout the evolution of scaled-distance modelling, this is an issue that has most often been presumed rather than proven (most likely due to the tediousness of the calculations involved). In the few cases when normality has been given some degree of consideration, the result has been the product of a simple visual inspection of frequency distributions: clearly unsatisfactory. However recently the soundness of this assumption has been brought into question, with obvious connotations for blast modelling in general. This paper considers this fundamental issue and seeks to investigate the normality hypothesis within the blasting context through an in-depth statistical analysis of what possibly can be described as an ‘ideal’ blasting dataset. This being a rare case study concerning an opencast coal site in England, where for the entire life of the site every single blast was monitored and recorded through the use of permanent monitoring stations. This has provided a unique ‘total population’ dataset of considerable size from which the assumptions of normality are put to the test.

Jan 1, 2005

By E Amini, M Scott

Grade Engineering® involves the planning, integration and operation of coarse preconcentration techniques to reject uneconomic material as early as possible in the mining value chain to improve the quality of ore delivered to mineral processing activities. These preconcentration techniques include screening for natural and induced deportment of grade to finer size fractions during blasting and coarse breakage, sensor-based measurements of grade and mechanised sorting at particle or bulk scales and coarse gravity separation. Over the last decade, the Cooperative Research Centre for Optimising Resource Extraction (CRC ORE), with the support of its participants, has developed a framework for the holistic evaluation of economic and production impacts attributable to these preconcentration techniques. The framework combines the characterisation of preconcentration responses, geostatistical modelling, process modelling and simulation of downstream and upstream production impacts and the optimisation of strategic mine plans to quantify changes in net present value due to different preconcentration strategies. This framework has been applied to evaluate preconcentration techniques at numerous metalliferous operations and can also be used to quantify changes in the environmental metrics for energy, water and steel consumption and emission, tailings and waste rock production. This paper collates the results of these Grade Engineering® studies to show the range and magnitude of economic and environmental impacts attributable to preconcentration. The studies have shown that rejection of uneconomic material prior to mineral processing activities can have a pronounced improvement in energy, water and comminution steel productivity, emission intensity and the profitability of metalliferous mining.

Nov 10, 2020

By Siyabonga Malevu

Chemical Initiatives? Umbogintwini plant is the production facility of Chemical Initiatives? business. Umbogintwini?s J Plant manufactures sulphuric acid. The plant was designed and built by Simon Carves, and was commissioned in 1974. The plant was designed to produce 500 tons/day of Sulphuric acid (H2SO4) at maximum rates. The Sulphuric acid manufacturing is through the famous contact process whereby liquid Sulphur is injected through dried air in a burner operating at 1000 °C to form sulphur dioxide (10.5% SO2). The SO2 gas is then cooled in waste heat boiler no. 1 before being fed to a four pass converter which provides 99.5% SO2 conversion to sulphur trioxide (SO3). The SO3 gas is the absorbed by 98.5% H2SO4 through the inter-pass & final tower to make more concentrated acid and dilute it with water back to 98.5% H2SO4 in acid pump tanks and dispatched to storage tanks. The manufactured Sulphuric acid is supplied to a variety of industrial manufacturing customers includes Pulp & Paper industry, Mining industry, Chemical manufacturing industry etc.

Jan 1, 2009

By S. W. Ip

Over the years, the importance of surface and interfacial phenomena has been neglected by the copper-nickel industry. As a result, little data on the surface and interfacial tension of the Ni matte and slag system are available in the literature. In view of the scarcity of information in this area, the surface tensions of the Ni-Fe-S system together with the Ni-Fe-S and fayalite type slag system were measured using the sessile drop technique. Drop images were obtained by X-ray radiography. For the Ni-Fe-S system, the results showed that the surface tension of the matte increases with matte grade. The surface tension behavior with changing matte grade showed a slight negative deviation from ideality. This indicated that FeS is slightly surface active in the nickel matte system. Results also indicated that small increase in sulphur content in the matte can decrease the surface tension quite significantly. The measured surface tension of the Ni-Cu-S system showed a linear relationship with the Cu2S content in the matte. The surface tension decreased with Cu2S content. Interfacial tension measurements showed a similar trend. That is, interfacial tension increased with increasing matte grade. The presence of MgO (-1.5%) and A12O3 (-6%) in the slag does not affect the interfacial tension value. Effects of matte surface tension on phenomena such as entrainment of matte in slag and infiltration of matte into refractory pores are discussed. The calculated flotation coefficients indicated that flotation of nickel mattes cannot be avoided by changing the matte grade. Filming of matte on bubbles can occur below a matte grade of about 19% Ni3S2. As for infiltration, refractory bricks containing high Cr2O3 will be easily wetted by matte regardless of matte grade. Therefore, bricks containing high Cr2O3 can easily be infiltrated by liquid matte.

Jan 1, 1993

By Blake M. Caldwell, Thomas C. Poulter

A new approach to an old problem has made it possible to do in a a tively short period what has not been accomplished in the past three quarters of a century using strictly experimental methods. A theoretical study was made of the underlying principles whereby a jet is formed by a shaped charge and of the mechanism of the penetration of the target by that jet. It was found that there are more than 10, and perhaps as many as 15 variables affectin!? the performance of the shaped charge. Only a few calculations are necessary to show that it is physically impossible to investigate all of these variables experimentally. The shaped charge theory has been extended to include a previously little-understood mechanism in high explosive phenomena; namely, low order detonation. By superimposing a high order detonation on a zone already undergoing low order detonation, all appreciable improvement in performance is accomplished. The development of a design wherehy these phenomena are coordinated in such a way as to develop a jet which is tailored to meet the specific target requirement will be described in detail. The shortcomings or even impossibility of strictly experimental techniques will be illustrated by a discussion of the development of a special-purpose explosive charge. INTRODUCTION In an article appearing in the May, 1888 issue of Scribner's Magazine, Charles E. Monroe described his early experiments with gun cotton (Fig. 1) which led to his name being most fre-quently connected with our present-day shaped charge. Although the sunken letters or "cavities" in Mon- roe's gun cotton were not lined, they produced some penetration of an iron plate. The credit for the lined shaped charge, however, should rightfully go to Dr. R. W. Wood of the Physics Dept. of Johns Hopkins University, who was responsible for first discovering the fact that a metal liner in a cavity of explosive gave high velocity fragments and/or jets of metal. This discovery was made by Dr. Wood inadvertently while investigating an accidental death resulting from an electric blasting cap. He discovered that a jet of high velocity copper particles was ejected from the dimple

Jan 1, 1958

By Wenshan Zhang

Three important methods of removing Fe in hydrometallurgy of zinc, manganese, copper, nickel, cobalt and etc are described, including neutralized hydrolysis method, jarosite method and goethite method. The reactions, technical requirements and thermodynamic analysis during Fe removal process are also discussed in this paper.

Jan 1, 2006

By Carlos Guillen Morales

Como parte del proyecto de estudio de impacto ambiental presentado por la Compañía Minera Antamina (Ancash), el presente trabajo describe la reutilización de las aguas residuales de los procesos mineros realizado en Huarmey. El estudio plantea el transporte el concentrado de mineral desde la mina hasta el puerto de embarque en Huarmey a través de camiones utilizando una carretera que facilitaría el desplazamiento de los mismos. Una vez llegado el concentrado al puerto de embarque, se separaría el agua del concentrado y el agua sería tratada para luego descargarla en el mar. Sin embargo, por análisis posteriores, se optó por otra propuesta más ecológica, donde se traslade los concentrados de cobre y zinc en suspensión acuosa a través de un minero ducto, y el agua tratada remanente del transporte de mineral, sería disipada mediante una plantación forestal, evitando la descarga al mar, generando empleo y una extensa área verde en el desierto de Huarmey. De forma que se innova en la minería a través de la reutilización de las aguas y se desafia las condiciones extremas del desierto costero para desarrollar una superficie vegetal que consumiera esta agua.

Sep 12, 2005

By S Hapugoda, J R. Manuel, M P. Ma, L Lu

Iron ore sinter quality depends heavily on the mineralogy, textures and physical structure of the sinter, which is formed upon solidification of the primary sinter melt. The interactions of the initial sinter melt with its surrounding materials will impact on the properties of the primary sinter melt and consequently the solidified structure of the sinter. By using a high-temperature visualisation system, in situ studies have been conducted on the effects of melt compositions (Al2O3, SiO2 and MgO) on the interfacial phenomena of the sinter melt on a natural iron ore substrate. It was found that the melt composition significantly influenced the wettability between the sinter melt and the iron ore substrate. The interactions between the sinter melt and the natural iron ore substrate were also examined. Such interactions can lead to further changes of sinter melt composition and hence the sinter melt properties that, in turn, further affect the wetting behaviour of the sinter melt.CITATION:Ma, M P, Lu, L, Hapugoda, S and Manuel, J R, 2013. Effects of melt composition on the interactions of sinter melt on a natural iron ore substrate, in Proceedings Iron Ore 2013 , pp 431-440 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By M. Wenzel, Dang Thanh Tung, Nguyen Anh Duc, Nguyen Huu Luong, Dang Van Sy, N. Kelly, K. Gloe, K. Kretschmer, Phuc Nguyen Le, K. Schnaars, S. Robles M, L. Götzke, J. J. Weigand

The recovery of rare earth metals from secondary sources has attracted much attention due to their ever expanding demand in the high-tech industry. The studies reported here focus on the hydrometallurgical recovery of lanthanum and cerium from spent fluid catalytic cracking (FCC) catalysts in a two-step process: leaching with nitric acid and solvent extraction by tri-n-butyl phosphate (TBP) and di(2-ethylhexyl)phosphoric acid (D2EHPA). The experiments show a high dissolution yield of about 93% lanthanum and 42% cerium in a single leaching step with 2 M (126 g/L) HNO3 at 80 °C; only 11% aluminum has been dissolved simultaneously. In the subsequent solvent extraction step the best results for this leach liquor could be achieved using a 1:1 mixture of 25% (v/v) TBP (0.92 M) and 25% (v/v) D2EHPA (0.76 M) in n-decane without the need for any pH adjustment. In that case La(III) and Ce(III) can be extracted with 60% and 74% yield respectively in one stage from the majority of accompanying matrix elements. In particular no extraction of Al(III) could be observed under these conditions.

Jan 1, 2016

By R. L. Kloberdanz

Peruvian legislation requires the preparation of an Environmental Impact Study (EIS) for new and expanding mines/beneficiation facilities and the preparation and implementation of an Environmental Adjustment and Management Program (PAMA) to control and mitigate environmental impacts associated with existing mining/beneficiation activities. Shepherd Miller, Inc., developed guidance documents for preparing an EIS and PAMA for Peru's Ministry of Energy and Mines and presented workshops to Peru's mining industry on preparing an EIS and PAMA. This paper discusses the process and approach taken and the results.

Jan 1, 1998

By T. Sterry Hunt

IT is now five years Since I called the attention of the Institute to the industrial importance of the coal and the iron ores of the Hocking Valley in Southeastern Ohio, and in a pamphlet on the region published Soon after, in 1874, endeavored to resume the principal facts then known respecting it, including the observations of the geological survey of Ohio, made and published up to the time by Professors Andrews and Wormley, together with an estimate of the probable future of the region, and its relations to the coal and iron markets of the country. Since that time the labors of the Geological Survey have included a further Study of the coal by Prof. Edward Orton, the results of which will be awaited with much interest. I may say from my knowledge of them, that while confirming the general conclusions of his predecessors, he has been enabled to add much to our knowledge as regards the correlation of the various members in different parts of the coal-field, and to Show more clearly the positions and the importance of the ore-beds in the Hocking Valley region. The only ore mined in that vicinity previous to 1874, was below what is called the Great Vein or No. VI coal, and to the west of what is known as the Hocking Valley coal-field, and although experiments in a few furnaces in the State had Shown that this coal could be used with advantage in iron-Smelting there was not a single blast furnace within the field. My observations at that time, however, impressed me with the abundance of iron ore, not only below but above this important coal Seam, and I then ventured to express the opinion that this region, from its cheap and easily mined Smelting-coal, its native ores and limestones, and its geographical position and relations to the great markets of the West, and to the supply of rich iron-ores from Lake Superior, was destined at no distant time to become a great metallurgical centre, where iron could be made more cheaply than at any other equally accessible point in the country. The object of the present communication is to report progress, and to State how far my observations made in the region last month have justified the predictions of 1874. The five years which have elapsed have been, as all know, most unfavorable to the iron trade, and especially to new enterprises in untried regions, yet they have not passed without important industrial developments in the Hocking Valley, where not less than thirteen blast furnaces have been erected

Jan 1, 1879

By Thomas C. Palangio

Since the advent of explosives, people have been trying to mechanize the process of loading it into long, narrow holes. Automated loading frees manpower from the arduous task of charging granular, cartridged and slurry explosives. An unexpected bonus of the automation process has been the realization of some valuable side effects such as high throughputs which speed up the loading process and higher loading densities which enhance explosive performance and permit hole patterns to be expanded.

Jan 1, 1990

The 53 countries that constituted Africa in 1993 accounted for a significant portion of total world output of a number of mineral commodities. For the continent as a whole, world shares of most commodities showed little change from those of 1992 although most output volumes showed a slight decline. There were no significant production increases, but there were significant decreases of cobalt and copper because of political instability in Zaire and production problems in Zambia, of chromite resulting from cutbacks in South Africa and Zimbabwe, and of phosphate rock owing to a lower output by producers in general. (See tables 1 and 2.) Among the most significant mineral commodities produced in Africa, ranked by portion of world production in 1993, were diamond, cobalt, chromite, gold, phosphate rock, manganese ore, uranium and petroleum. Others of importance in world trade were andalusite, antimony, asbestos, bauxite, coal, copper, fluorspar, lithium minerals, platinum-group metals (PGM), titanium minerals (ilmenite and rutile), vanadium, vermiculite, and zircon. Several of these-chromite cobalt, diamond, and manganese-were not produced in the United States.

Jan 1, 1995

By M. Jawed

Coking coal reserves in India are distributed geographically in Giridih, Raniganj, East Bokaro & Jharia Coalfields (J.C.F.). 97% of prime coking coal in JCF coming through underground mines is credited to Bord & Pillar mining systems inspite of the fact that it results in heavy mining losses. The cost of mining in B & P mines has been much higher due to various factors. In this paper, O.R. model has been discussed with case study for optimizing the cost of production in operational underground mines. Also, a computer algorithm has been discussed using a schematic flowchart, which provides the trend of mining-losses 'in different mining, systems with changing design parameters and finally selects, the optimum mining system for undeveloped seams based on economic appraisal criteria.

Jan 1, 1989

By Mark S. Dunsbier, Steven J. Schatzel

Large roof outbursts began occurring in November 1986 at Domtar's Sifto Salt Mine in Goderich, Ontario, Canada, working the bedded Salina A-2 Salt unit. The outbursts, measuring about 13-20 m in diameter, released high concentrations of methane from cavities that extended into carbonate roof units. Spontaneous ignitions of methane gas during an outburst seriously burned a mine technician. The Canadian Ministry of Labour contacted the U.S. Bureau of Mines for technical assistance to aid in mine managements1 efforts in alleviating the problem. Initial gas content determinations of salt samples from the outbursts by acoustic test methodology revealed no methane enrichment. In- mine core drilling and subsequent methane content testing indicates the main source of methane in overlying roof units. Drilling the roof units demonstrated the potential of draining methane from areas showing signs of impending outbursting and alleviating the danger. Three mechanisms are considered the most likely means by which methane was introduced to the mine environment. These are (1) hydrocarbon gases released from brines, (2) gas transport along horizontal bedding planes or gas accumulations in bedding separations, and (3) mining-induced fracturing. The abundance of higher hydrocarbons in gas yielded by non-evaporite rock samples from the Goderich mine may be indicative of a former association with liquid petroleum.

Jan 1, 1989

By N. E. Idenyi

The effects of compositions and firing temperatures on the physico-mechanical properties of blended Nsu fireclay and Nkalaha redbrick clay have been investigated. The clay samples were compounded according to the following ratios: 10:90, 20:80, 30:70, 40:60 50:50, 60:40, 70:30, 80:20 and 90:10 in the order Nsu: Nkalaha respectively, and test samples made and fired at 9000C, 10000C 11000C and 12000C. The properties tested for were the modulus of rupture, porosity, shrinkage, apparent density, water absorption and bulk density. From the results obtained, it is inferred that the blends have a maximum service temperature of 11000C, with the 30: 70 blend presenting the best characteristics. A conclusion is drawn to the effect that the blend could be adapted for the production of ceramic earthenware, electrical porcelain pin insulators, cement manufacture and for refractory linings where temperature requirements are less severe.

Jan 1, 2006

By George A. Morgan

The 53 countries that constituted Africa in 1989 accounted for a significant portion of total world output of a number of mineral commodities. Among the most significant minerals to be produced in Africa were andalusite, antimony, asbestos, bauxite, chromite, coal, cobalt, copper, diamond, fluorspar, gold, lithium minerals, manganese, phosphate, platinum-group metals, and the titanium minerals-ilmenite and rutile, vanadium, vermiculite, and zircon. Despite the underdevelopment of much of Africa, mineral raw materials played a very important part of the national economies of many of its countries. In terms of percent-age of export earnings, minerals accounted for more than 90% in some cases. In several countries with agrarian economies and little economic diversification such as Angola and Guinea, a single mining operation could represent an important source of foreign exchange. These latter operations tended to be the more easily mined surface deposits of diamond, gem stones, and precious metals. Mineral commodities for which Africa had a high percentage of world output were bauxite, 16%; chromite, 44.5%; cobalt, 76.5%; copper, 13.9%; diamond, 50.7%; gold, 32.9%; manganese, 27.1 %; phosphate, 22.1 %; platinum-group metals, 48%; uranium, 29.2%; vanadium, 54%; and vermiculite, 41 %. Several of these, chromite, cobalt, diamond, and manganese, were not produced in the United States.

Jan 1, 1992