Search Documents

By H. E. Cline, T. H. Alden

A study zvas made of rate-sensitive plastic deformation and superplasticity in alloys of lead and tin. These alloys (lead, PO-19 pct Sn, Sn-38 pct Pb, Sn-2 pct Pb, tin) were extruded, aged at room temperature, or melted and resolidified to produce a variety of ~nicrostrnctures. Flow stress us strain rate data were obtained frorn tension tests for strain rates between 10-6 and 1 min-1. The curve log o .us log £ was S-shaped jor fine-grained materials and approxinzately linear for coarse-grained nzaterials. At constant grain size, the behavior was relatively insensitive to conposition. High rate sensitivity (d log o/d log k) and superplasticity occurred at intermediate strain rates in fine-grained materials and are believed to be associated with a transition with strain rate in the mode of plastic flow. This transition was shifted to higher strain rates with increasing temperataire or decrensing grain size. The high rate rneclzanisrn is presunzed to be slip, while rnetallographic evidence sug-gests that the low rate lnechanism is pain boundary sliding. PEARSON' discovered that extruded eutectic alloys of Pb-Sn and Bi-Sn could be elongated as much as 2000 pct in tension. The ability for stretching decreased with aging time or annealing to increase the grain size. At high strain rates, or if the material was in the cast condition, normal ductility was observed. Following deformation of the extruded Pb-Sn eutectic at low rates, Pearson observed an equiaxed granular structure on an initially flat surface, while rapid straining produced elongated grains. He attributed the large deformation in the extruded alloys to the persistence of extremely small grains to a temperature sufficiently high for inter granular flow. Avery and backofen2 measured the strain rate sensitivity of the flow stress, m = d In old In 6, in the Pb-Sn eutectic and established a correlation between m and the tensile elongation. In the extruded eutectic alloy the strain rate sensitivity was 0.1 to 0.2 at rapid rates and the elongation was small, while at low rates m increased to 0.4 to 0.6 and superplastic elongation was observed. They also noted a grain size effect. In the case of the cast Pb-Sn eutectic the strain rate sensitivity remained at 0.1 over the range of strain rates of their experiment (3 x 10"3 to 2 min-I). These authors suggested that diffusional (Nabarro-Herring) creep was the mechanism by which deformation occurred at low strain rates, while climb-controlled creep occurred at high rates. Two predictions of this model are that, at low strain rates, the strain rate sensitivity approaches 1, i.e., Newtonian viscosity, and that the strain rate at constant stress varies as D/L2, where D is the coefficient of self-diffusion and L the grain size. More recently, a mechanical and microstructural investigation of the dilute superplastic alloy, Sn-5 pct Bi, has been done.3 The results show that the high strain rate sensitivity is associated with a transition with strain rate of the mechanism of plastic flow. At low strain rates, grain boundary sliding and its associated accommodation processes were evident, while at high strain rates quasi-uniform slip was concluded to be the dominant deformation process. The following experiments were performed to extend our knowledge of the phenomena of superplasticity to a larger range of strain rates, compositions, temperatures, and microstructures in the Pb-Sn alloy system. The question of why a cast structure does not exhibit viscous behavior although it appears to have a fine microstructure2 was investigated.

Jan 1, 1968

By H. Huang, R. N. Gow

Acidic treatment of enargite (Cu3AsS4) dissolves both arsenic and copper from the mineral and then attempts to separate them in the leach solution. The reactivity of enargite was examined in acidic to neutral solutions, over the pH range 1-7, to determine a potential range for co-dissolution. Enargite mineral samples from Butte, MT and Quirivilca, Peru were used as working electrodes in a cyclic voltammetry corrosion cell setup, which were then cycled multiple times over -1000 to 1000 mV. Surface reactions and transitions were characterized using in-situ Raman spectroscopy, which were then compared to updated EH-pH diagrams for the copper-arsenic-sulfur-water system from a previous study done under alkaline conditions. The region of co-dissolution is limited to > 600 mV vs. SHE and pH < 1 under the proposed diagram.

Jan 1, 2014

By V. Kamavaram

Ionic liquids are novel salts used as potential non-aqueous electrolytes for aluminum electrolysis at low temperatures. In the current research di-alkylimidazolium chloride ionic liquids such as 1-butyl-3-methylimidazolium chloride ([BMIM]Cl) and 1-hexyl-3-methylimidazolium chloride ([HMIM]Cl) were investigated for aluminum electrolysis. Melt formed by mixing ionic liquid with AlCl3 is termed as chloroaluminate and is composed of several polymeric chloroaluminate anions. Ionic liquids are studied as electrolytes for aluminum electrowinning and electrorefining of aluminum based materials (A356, A360, & Al-MMC) at low temperatures. Mechanism of aluminum electrodeposition in these chloroaluminate ionic liquid electrolytes was investigated using electroanalytical techniques such as cyclic-voltammetry and chronoamperometry. Aluminum electrodeposition on pure copper substrate in AlCl3-[BMIM]Cl (1.5:1.0) electrolyte at 30°C melts was found to be quasi-reversible process with a charge transfer coefficient ( of 0.40. Chronoamperograms obtained at different voltages in the range (-0.1 to -1.0 V) revealed that the initial stages of aluminum deposition in AlCl3-[BMIM]Cl melts was instantaneous nucleation followed by diffusion controlled growth of three-dimensional aluminum nuclei. The diffusion coefficient of electroactive species Al2Cl7¯ in AlCl3-[BMIM]Cl melts was found to be 6.5×10-7 cm2 s-1 from Cottrell?s equation and 3.9×10-7 cm2 s-1 from the dimensionless current-time transients.

Jan 1, 2006

In 2006, a total of 7,178 sand and gravel mining operations reported employment to the Mine Safety and Health Administration (MSHA).1 ? Sand and gravel mines were the largest mining sector, comprising 48.2% of all mining operations. ? Sand and gravel mines were found throughout all 50 states and Puerto Rico.

Sep 1, 2008

By R C. Morris

Two major types of economic secondary iron ores occur in the banded iron formation (BIF)-rich Hamersley Province of the Pilbara, Western Australia:dominant BIF-hosted bedded iron deposits (BID)detrital ore deposits (DID sensu lato), which are mainly hosted in the three province-wide Cenozoic sequences that include coeval non-ore sediments and comprise:a. the major Miocene, fluvial channel iron deposits (CID)b. the lesser Eocene and Pliocene detrital iron deposits (DID sensu stricto).Striking differences exist between the massive CID resources and the much smaller underlying and overlying DID. CID are essentially riverine alluvial ooidal rocks with abundant small fossil wood fragments and variable iron peloids, but with only extremely rare recognisable lithic remnants. The original matrix is typically ramifying layered goethite. Eocene DID are mainly alluvial with minor pisoids, whereas Pliocene–Quaternary DID are dominantly coarse colluvial gravels, both derived from and largely retaining the original textures of BID, hard cap or variably ferruginised surface BIF. The colluvial DID matrix is typically ferroan-aluminous soil, resulting in canga where replaced by goethite, which may be dehydrated to hematite by exposure. The Cenozoic deposits occur in two dominant geomorphological environments: the southern Marra Mamba to Brockman Iron Formation strike valleys containing all three Cenozoic sequences and the much later northern Brockman Iron Formation plateau valleys that include only the Miocene and Pliocene sequences. The Cenozoic detritals formed in different climatic regimes, with an extended dry period forming a prominent province-wide dehydrated carapace on the Eocene DID. The Miocene ‘optimum’ followed with its thick scrub-covered deep regolith that produced the fossil wood-rich CID and was succeeded by the arid cool period of the Oakover limestone/calcrete. A major renewal of exposure and erosion in the Pliocene resulted in the extensive iron gravels of the Pliocene–Quaternary.CITATION:Morris, R C, 2015. The Cenozoic detrital iron deposits of the Hamersley Province of Western Australia – a tribute to Mal Kneeshaw, in Proceedings Iron Ore 2015, pp 319–326 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By D. A. Reynolds

THIS PAPER gives results of an investigation of the composition and carbonizing properties of coals from the Beckley bed, Caretta No. 5 mine, Susanna, McDowell County, and Glen Rogers No. 2 mine, Glen Rogers, Wyoming County, W. Va. The investigation included BM-AGA carbonization tests at. 800° and 900° C. and various chemical and physical tests designed to evaluate agglutinating, plastic, and expanding properties of coal. Both coals were of low-volatile bituminous rank, and each was blended with 70 and 80 percent high-volatile A coal from the Pittsburgh bed, Warden mine, Allegheny County, Pa. The Beckley bed was 39 to 58 inches thick at three points in the Caretta No. 5 mine, and the coal was 39 to 49 inches thick. The carbonizing sample contained 83.0 percent fixed carbon on the dry, mineral-matter-free basis. It contained 3.1 percent moisture, 15.8 percent volatile matter, 72.4 percent fixed carbon, 0.7 percent sulfur, and 8.7 percent ash, as carbonized. The ash softened at 2,680° F. The free-swelling index was 7;i, and the agglutinating value was 7.7. This sample fused weakly in the Gieseler plastometer; its blends with 70 and 80 percent Pittsburgh coal attained maximum fluidities of 830 and 600 dial divisions per minute, respectively. The single coal yielded 83.0 percent coke at 900° C. Yields of other carbonization products per ton of coal at 900° C. were: Gas, 9,950 cubic feet; tar, 3.5 gallons; light oil, 1.36 gallons; and ammonium sulfate, 16.3 pounds. Blending with Pittsburgh coal lowered the yield of coke and raised the yields of other products significantly. Caretta coal yielded strong, blocky coke at 900° C., 89 percent of which was plus-2-inch size. Strength indexes of 900° C. coke from 30:70 blends of Caretta No. 5 and Pittsburgh and of Pocahontas No. 3 and Pittsburgh coals were, respectively: 2-inch shatter, 68 and 53; 1%-inch shatter, 90 and 85; 1-inch tumbler, 50 and 53; and %-inch tumbler, 62 and 65. The specific gravity of the 900° C. gas from Caretta No. 5 coal was 0.272, and the heating values were 491 B. t. u. per cubic foot and 2,440 B. t. u. per pound of coal. The blends yielded much richer gas. Yields of tar acids and bases (0.09 and 0.04 gallon per ton, respectively) were within the normal ranges for low-volatile coals. Caretta No. 5 coal expanded 7.5 percent in the sole-heated oven at a charge density of 55.5 pounds per cubic foot. The blends containing 70 and 80 percent Pittsburgh coal contracted 4.8 and 7.5 percent, respectively.

Jan 1, 1953

I strongly endorse Mr. Jackson&apos;s (Inland Steel Company) oral comment on the authors&apos; paper that, as blast furnace slag is removed from the BOF charge, lime solution may be retarded. After two or three pourings, the blast furnace slag will contain some iron oxide and considerable manganese oxide, and it is hot and possibly still liquid. A few thousand pounds of this slag will speed up the slag development rate considerably and could be considered a good auxiliary flux. Although the removal of blast furnace slag from the BOF charge lowers the total sulfur load by 40 to 50%, we must have a good, quick slag development in the BOF to bring .030 to .035% sulfur hot metal to .020%, a requirement on a high percentage of our steels today. In discussions at off-the-record meetings and one not published at last year&apos;s annual meeting as well as discussions with many operators over the past 1-1/2 years, I predicted that the removal of blast furnace slag could slow down lime dissolution and that, if a shop had dissolution problems before, the problem could be quite serious.

Jan 1, 1972

By Robert Dickson

Princess colliery is operated by Old Sydney Collieries, Limited, a direct descendant of the General Mining Association of London, England, which, in the first quarter of the nineteenth century, pioneered in coal mining in Nova Scotia. The coal worked is a 5 ft. 6 in. seam known generally through the Sydney coalfield as the Harbour seam but referred to locally as the Sydney Main. Entry is made by shafts, 680 feet deep, sunk in 1871 on a headland forming the northern entrance to Sydney harbour. From them extend the main roadways of the colliery, a distance of 700 feet to the shore line and a further distance of 14,700 feet in submarine areas to a total length of 15,400 feet. It was the first colliery in Nova Scotia designed to work submarine areas. Lateral development extends across a frontage of 16,000 feet and the submarine area from which the coal has been extracted is slightly over 6 square miles. There yet remains sufficient territory ahead of the workings to assure a future life to this colliery estimated at over 80 years at the current rate of production. In this area the seam dips at 6 to 7 per cent and face workings have reached a depth of 1,690 feet below the sea level. Until 1923 extraction of the coal was by room-and-pillar, followed by the drawing of the pillars. At that date the superincumbent strata had reached a thickness of 1,400 feet, resulting in heavy weighting on the roof and severe side pressure on the coal ribs. In combination with a soft, heaving pavement this created a set of conditions involving great difficulties and expense in keeping open places driven in the solid sufficiently long to permit recovery of the coal in the pillars by methods and equipment then available. The operator was forced to resort to extraction by longwall as the only economical method of winning the coal.

Jan 1, 1948

By Barbee J. Scheibner

This Bureau of Mines report describes the geology and physical properties of core samples at the Sunnyside coal mine No. 1, Sunnyside, Utah, and was written in conjunction with the Single-Entry Program conducted at the mine. The objective of this program was to test the hypothesis that the single-entry system in the Sunnyside mine, supported in the center by open cribs and divided by a fire-resistant partition, is equivalent to or better than a two-entry sys-tem. Drill cores, taken underground at 15 sites in the single-entry study area, facilitated the construction of geologic cross sections of the entries. Physical property data obtained from the drill cores was used in a three-dimensional finite element analysis program to evaluate the stability of the openings, the support requirements, and the de formation characteristics of the roof and floor material. Data on 10 physical property parameters for 5 rock types plus coal are also tabulated and discussed.

Jan 1, 1979

By Francois E. Heuze

We demonstrate a new capability to analyze the behavior of circular shafts in jointed rock. This was made possible by the development of a new, axisymmetric, joint finite element (2). Whereas the only previously reported such element was singular (1) and inadequate at some orientations, the current element has been extensively validated (3). The need for including discontinuities in a shaft analysis comes from two sources. First, the various rock formations may have discrete jointing, bed- ding, and interface between them. Second, there is a joint at the boundary between a concrete liner and the rock, and possibly between the various segments of the concrete liner. To demonstrate the applicability of the new model, we analyze a vertical circular shaft 5.4 m in diameter, in a series of horizontally bedded sandstones and siltstones. The shaft excavation is followed through three initial steps: 6 m, 15 m and 24 m deep.

Jan 1, 1979

"Located at Canyon Ferry on the Missouri River, 17 miles from Helena and 63 miles from Butte. River drainage area 15,570 sq. miles. Built in 1898.DAM: Rock-filled, wooden crib, 490' long and 39' feet at maximum head; also masonry core, earth bulk-head 300' long and granite masonry abutments.SPILLWAY: 473' long, crest elevation 3660.5; steel flashboard system 10' high.PENSTOCKS: 10 main penstocks, 12' diam., about 40' long, leading from canal to turbines, each supplying 1 pair turbines.WHEELS: 4 main center discharge, horizontal units, each 1 pr. of 42"" wheels made by Dayton Globe Iron Works, and 6 main units, each 1 pr. of 45"" wheels made by S. Morgan Smith Co., all 157 r. p. m., normal head 34', and direct coupled to generators.GENERATORS: 10 W. E. & M. Co., Kodak Type, revolving armature, 750 k-w., 157 r. p. m., 550 v., 3 phase, 60 cycle alternators.OPERATION: The plant has large water storage and can carry peak loads to 12,000 h-p. It is the central control station for the system."

Jan 1, 1913

By Morgan M. Sears, Gamal Rashed, Jim Winfield, Brent Slaker

"Over the past decade, ground falls have resulted in five fatalities, representing over 40% of all fatalities occurring in underground stone mines in the United States. In conjunction with recent high-profile pillar collapses, the need for further ground control research in the nation’s stone mines is evident. Ground conditions are growing more difficult. Therefore, this research is focused on deep cover, steeply dipping, and multi-level underground nonmetal mines. The objective of this paper is to introduce a geomechanical study of pillar development in a steeply dipping limestone deposit. To accomplish this, a numerical model was developed using input from modified laboratory test data and in situ stress measurements provided by the mine to simulate the development of a pillar under these conditions. The model was then verified against field observations and stress mapping. The calibrated model was then used to calculate the estimated stresses in the pillar and immediate roof as development progresses around an instrumented pillar.INTRODUCTIONGround falls represent a significant hazard in the nation’s underground stone mines. In response to recent large-scale pillar collapses, as well as stakeholder interactions, researchers from the National Institute for Occupational Safety and Health (NIOSH) are currently conducting detailed investigations into the complex loading conditions at mines operating in challenging operational environments. These include deep-cover, steeply dipping, and multi-level mines where there is the potential for an increased risk of ground failure. The Pleasant Gap Mine, shown in Figure 1, operates in the Valentine Formation, which is typically light grey, extremely fine-grained limestone, and approximately 21.3 m (70 ft.) thick. The Centre Hall Formation makes up the immediate and main roof members and is approximately 9.1 m (30 ft.) thick, consisting of medium-dark-gray limestone (Murphy et al., 2018). Situated in a syncline, the top of the Valentine Formation dips at approximately 19° with a strike of approximately N54E in the area of interest (see Figure 2)."

Jan 1, 2018

By P Breuer, A Simons

The sulfidisation, acidification, recycle and thickening (SART) process is currently being used at NewcrestÆs Telfer Gold Mine to recover cyanide and copper from the cyanidation tails of the pyrite concentrate carbon-in-leach (CIL) process. While the process has been effective at attaining high recoveries of cyanide and copper, the Telfer SART plant has experienced higher than expected sulfide additions to achieve these recoveries. This paper details the results of surveys on the Telfer SART plant, which show that residence time appears to be causing the high sulfide consumptions. The paper also details the results of laboratory scale experiments which confirm the observed residence time impact during the acidified stage of SART.CITATION:Simons, A and Breuer, P, 2013. The impact of residence time on copper recovery in Telfer Gold MineÆs cyanide recycling process, in Proceedings World Gold 2013 , pp 189-196 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By N. Ono, H. Fujiwara, S. Otsuka-Yao-Matsuo, T. Omata

"The electrical conductivity and the oxygen release and uptake of sintered indium tin oxide (ITO) upon heating and cooling under the condition that P(O2)/P*=4.9X10-4 (P* = atmospheric pressure), :when P(O2) was approximately 50Pa, were simultaneously measured by using a closed-system oxygen-gas analyzer. A large increasing in -the electrical conductivity - upon the· oxygen release detected in 1130<T<1273K was observed. Quantitative relationship between the number of oxygen atom released from ITO and the conduction electron density in ITO was studied. The release of one oxygen atom agreed with the generation of two conduction electrons, i.e., the efficiency-carrier-generation for the oxygen release from the ITO was almost one. The oxygen atom released must be originally at the quasi-anion site in the C-type rare-earth lattice, i.e., the 16c site in the space group of Ia3, as an interstitial excess oxygen, Oi"". It was concluded that the mechanism of conduction carrier generation and compensation upon SnO2 doping into In2O3 can be expressed by the defect equation, 2SnO2-2Sn1n +2(1-z)e'+zOi""+3O0 x+(l-z)/2O2, and that the oxygen release bringing the increase in the electrical · conductivity can be expressed by the equation, Oi""-1/2O2+2e'.IntroductionThin films of SnO2-doped In2O 3 (generally designated as ITO, for indium tin oxide), which have high optical transparency for visible light and high electrical conductivity, have been used as transparent electrodes for liquid crystal and electrochromic displays. It is well known that the electrical conductivity of ITO depends on the content of SnOi-dopant and oxygen. However, a reliable relationship between electrical conductivity and the absolute oxygen content in ITO has yet to be reported. The elucidation of such a relationship is one of the important clues for realizing extremely highly conductive ITO electrodes."

Jan 1, 2000

By J. J. Whittaker

Zaldivar is an open pit copper mine operation located in the Atacama Desert, in northern Chile. The plant produces Cu cathodes using 4 solvent extraction trains. The plant was started up May 1995. Since 1996 the plant has been using on-stream analyzers based on X-ray fluorescence and titration for process monitoring and control. Elemental analyzer alone is not able to provide the critical information for plant operation, it has to be complemented by on-stream titrators integrated to one sampling system. The analyzers are located in a prefabricated shelter. The analyzer system project, operation and performance issues are the main topic of this paper.

Jan 1, 1999

By Homer Turner

COALS, other than anthracite, have been so thoroughly studied under the microscope during recent years, that we now know what kinds of plants and what parts of plants form the bulk of lower rank coals from peat to bituminous coal. The microscope has also shown the state of preservation of such vegetation as well as the nature and distribution of products of plant decay. These and further details have been ascertained mainly through the employment of two methods of attack, section cutting and maceration. Anthracite has failed to respond to these methods, so well adapted to the study of lower rank coals and, therefore, has been neglected by investigators to such an extent that there is much doubt as to its microscopical characteristics. The object of this paper is to lift anthracite from its realm of obscurity by demonstrating the wealth of microscopical detail that is revealed when reflected light is used on a properly polished and etched surface and, further, to show the relationship between anthracite and bituminous coal.

Jan 2, 1925

By Bowra N

Working capital is best described as money that must be supplied from a company&apos;s treasury to buy inventories for raw materials and finished products and to provide credit to customers who have not yet paid for delivered products. Working Capital requirements for resource projects are to a large extent, dependent on specific characteristics of the projects concerned. Important variables are the nature of the project and speed with which sales can be realised. The project&apos;s location is also important as this will influence inventory levels. Working capital requirements have a time profile, the present value of which can represent a significant portion of a projects overall capital needs. A significant component of a project&apos;s working capital is not readily recoverable or able to be reassigned should the project fail or be deferred.

Jan 1, 1986

By E. G. Gaylord

THE material improvements which have been made in the practice of exploiting oil and gas reservoirs in the United States during recent years may be attributed largely to: (1) The necessity for drilling deeper wells at costs not much greater than was formerly expended on shallower wells. (2) The necessity for producing oil at a lower cost per barrel. (3) A growing recognition of the importance of the nature of production practice upon ultimate yield of oil and gas. The first two of these factors result, to a large extent, from the fact that a greater proportion of new development has been deeper development, and these wells have been drilled in the face of progressively lower per well allowables. In California, for instance, maximum allowables have declined from 400 barrels per day in March, 1938, to 156 barrels per day in September, 1940, and during this same period some 125 wells were drilled to the deeper 10,000-foot producing horizons discovered during this time. The third item listed above results from our increasing knowledge of the basic factors which influence the amount of recovery we may expect from reservoirs. In addition to the longer-range planning now being undertaken by the more prudent operators, State proration and conservation laws have focused attention upon the importance of methods conducive to obtaining progressively greater quantities of the hydrocarbons in place. In a paper of this length it will be possible to discuss only a few of the recent advances. An effort has been made to select the more important of these and to indicate, where possible, the factors which have made these advances possible.

Jan 1, 1941

By Gordon Cook

American Electric Power Company (AEP operates 31 coal mines in three states, and some 26 electric generating stations (19 coal-fired) located in the Ohio River Basin. Normally the system burns over 36,071,600 tonnes (40,000,000 tons) of coal and generates in excess of 3.6 X 1018 J (100 billion kwh) of electricity per year. In 1975, AEP, in response to the progressively more stringent air quality requirements of the clean air act, acquired large low-sulfur reserves in Carbon County, Utah (Figure 1. Location Map). Price River Coal Company (PRCC) is the operator OF this multi-seam complex, which is part of the Book Cliffs coalfield at an elevation exceeding 1,829 m (6,000 ft.). The topography is mountainous and divided by numerous canyons. Flat areas are at a premium (Figure 2. Castle Gate Area). Modern high production longwall mining takes in some top and bottom waste, and in this particular operation, it amounts to about 14% of the ROM tonnage.

Jan 1, 1983