Search Documents

By Theophili CN, Kapenis AP

Seismic tomographic imaging has been applied to determine the blast induced damage zones in bauxite pillars in underground mining. At the retreating stage, when pillar dimensions are reduced from 8 x 8 m to approximately 5 x 5 m, the' seismic tomographies reveal, through measurements of the P-wave velocities which is a measure of the degree of fracturation of the pillar rock mass, the presence of three zones within each pillar. In the external zone, where velocities recorded are below 750 m/s. extensive pillar damage occurs which is attributed to both the growth and coalescence of pre-existing cracks and even the creation of new cracks in the rock mass. This effect is in agreement with literature, when considering the peak particle velocity as a criterion for rock failure in tunnels. In the intermediate zone, where velocities range between 7S0-1000 m/s, damage to a much lesser extent occurs which is due mostly to growth of pre-existing cracks and widening of their apertures. The inner zone, where velocities exceed 1000 m/s, is considered to be unaffected by blasting. Simple remedial measures of low cost, which are based on blasting mechanics are proposed to minimise the blast induced damage zone and consequently the transition zone.

Jan 1, 1995

Jan 1, 1969

By M. W. Von Bernewitz, J. J. Forbes

"In the United States there are hundreds of underground and surface (inside and outside) inclines at coal mines on which trips of cars are continually being run with coal, rock, supplies, and men. The safety of the men and prevention of damage to the slopes depend, excluding the personal element of the hoist-man, on the strength and condition of the wire cable, draw bars, and the couplings, and on the links of chains and pins as well. Within a recent period of four weeks there have been two runaway trips, one on the surface and one underground; it seems desirable to call attention of mechanical engineers and others at coal mines to the need for closer and more frequent inspection of the cable, draw bars, coupling links and pins, derailing devices, wheels, brakes, and other parts of cars or trips on which men are hauled on inclines. This bureau has never published anything on this class of accident heretofore.How frequently runaway trips occur is not known. If no serious injury or fatalit has to be reported to the State authorities, a number of such happenings may occur and not be mentioned outside of the immediate vicinity of the mine.Runaway trips can and do result in considerable loss of life, in injuries, and damage, either at or near the place of the break, or throughout a mine by causing an explosion of gas or coal-dust or both, This report is restricted to a study of the mechanical and physical phases of car trip construction and of the metal of couplings and ropes; derailed trips are not included and may be the subject of another paper. There is no need to mention gas accumulations, coal-dust and rock-dusting, open lights, protected power lines, and permissible equipment, because these have all been well covered in Bureau of Mines publications which have been widely distributed and partly or wholly reprinted by others.Most of the items regarding the runaway trips tabulated have been abstracted from reports made respectively by Clarence Hall, W.O. Snelling, and J. W. Paul; D. Harrington and J. J. Forbes; H. C, Howarth and G. S. McCaa; K. L. Marshall and E. H. Denny; J. J. Forbes, G. W.- Grove, and R. D. Currie; S, P .Howell and K. L. Marshall; and .J. W. Paul, H. D. Mason, and G. E. McElroy, all of the mining and safety divisions; and C. H. Herty, jr., and G. R. Fitterer of the metallurgical section of the Bureau of Mines. W. J. Fene, K. L. Marshall, and S. P. Howell of the safety division, and J. F. Lessig, mechanical engineer, and G. St. J. Perrott, superintendent, Pittsburgh Experiment Station, read the text and offered sugges¬tions. W. J. McGregor, coroner for Allegheny County, and P. F. Nairn, State Mine Inspector of Pennsylvania, contributed valuable information."

Mar 1, 1931

By Jakub Szary

Excavation and shoring adjacent to the above-grade Gilmore train station and elevated guideway was undertaken in 2019. A perimeter secant pile cut-off wall was constructed to a depth 37 m (121 ft) below ground surface consisting of 1.0 m (3.3 ft) diameter drilled piles spaced 750 mm (2.5 ft) on-center, tied back with soil anchors, and reinforced with W610 steel sections every 4th pile. A bracing/jacking system was also constructed to support 3 free-standing guideway caissons within the excavation. An automated instrumentation program was installed to monitor movements of shoring walls and train infrastructure in real time and consisted of a robotic total station, inclinometers, tiltmeters, strain gauges, extensometers, and anchor load cells. Baseline monitoring was able to establish diurnal and seasonal movements within the structure, strongly correlated with temperature. The system actively monitored various shoring elements and train infrastructure in real time and alerted the project team when values exceeded predetermined threshold values. Remote reconfiguration of the automated system allowed for more frequent monitoring during jacking of Pier 29 in March 2022. Monitoring data was in agreeance with on-site manual surveying results and jacking dial gauges, and proved to be a reliable monitoring system for construction applications.

Sep 1, 2022

By Ernie M. Crist, Laurentiu Nastac, Frank Spadafora

"This paper describes the modeling techniques and the experimental and computer results for two casting processes that are under development and optimization. These processes are described as follows:1) Electromagnetic stirring (EMS) during casting of Ti-6Al-4V round ingots using the plasma arc cold hearth melting (PAM) process: The purpose of EMS is to establish a singlemelt PAM process capable of consistently producing as-cast ingots without helium porosity and also having no need for surface conditioning prior to secondary processing.. The modeling approach is based on the numerical solution of Maxwell's equations, fluid flow, and heat transfer equations, and mesoscopic modeling of the grain structure.2) Casting of Ti-6Al-4V slabs using the single-melt PAM process: The purpose of slab casting is to improve yield by eliminating an intermediate blooming step for converting round ingots to slabs. The modeling approach is based on the numerical solution of fluid flow and heat transfer equations. The effects of pouring and mold temperatures on the pool and temperature profiles were studied. Also, the torch effects (such as the torch standoff and its traversing path) on the pool and temperature profiles were investigated and the best-case scenario was used in the experiments. Evaluation results at RMI Titanium Company showed that the plates made from the slabs met the mechanical properties and microstructure requirements.Acknowledgment. This work was conducted by the National Center for Excellence in Metalworking Technology (NCEMT) operated by Concurrent Technologies Corporation (CTC) under contract No. N00014-00-C-0544 to the US. Navy as part of the US. Navy Manufacturing Technology Program. Dr. K. b. Yu from RMI and my colleagues from CTC are acknowledged for their comments on this work."

Jan 1, 2004

As a kind of collector, Xanthates are generally used to make sulfide minerals hydrophobic in flotation process. Xanthate adsorption on a galena surface has been widely studied experimentally. In this paper, DFT methods were employed to investigate the local adsorption interactions about the collectors,such as ethyl xanthate (CH3CH2OCS2?, EO) and ethyl trithiocarbonate (CH3CH2SCS2?, ES), absorbing on two different PbS clusters. From the results, it can be easily found that, on the edge or at the apex, both collectors, with two S atoms bidentate coordinating on the clusters, have surprising interaction energies, while on the surface, its interaction is relatively weak in the form of monodentate ligand. NBO analysis results reveal that there is at least a covalence bond with sulfur atom about 10% and lead atom about 90% when the absorbed lead is on the lattice edge or at apex, but, if the absorbed lead is on the lattice surface, no covalence band would be found. Meanwhile, the S-Pb bond, formed by the absorbed Xanthate and galena lattice, seems to have much more covalence characteristic than that formed in the PbS lattice inner. Furthermore, those data also imply that the difference of the collecting effect between the EO and the ES may be not notable, because of the similar distance and the interaction energy for the same interaction mode.

Jan 1, 2014

By H. M. FRENCH

ARC welding can be defined as a process whereby two A pieces of metal are brought together, heated to a molten state by the heat of an electric arc, and fused into one piece. There are several kinds of arc welding: the metallic arc, the carbon arc, the atomic hydrogen arc and the shielded arc methods. A short description of each, together with its major applications, will serve to distinguish between them. Metallic arc welding involves an arc drawn between a metal electrode and the material to be welded, called the work or the "parent metal." It may be further subdivided into hand and automatic welding, depending on whether the electrode is fed to the arc by hand or by motor drive. This form of arc welding can be applied to most welding operations. Exceptions to its use consist of applications where very thin metals are to be welded; where it is desired to join the work with- out adding metal; or where extreme ductility may be required:

Jan 1, 1930

By J. W. Watkins

This report describes in detail methods of making corrosion tests and chemical analyses that have been used extensively and satisfactorily in a study of plants in which various surface, waters and brines are conditioned and used for water flooding, brine disposal, and reservoir-pressure maintenance in Kansas, Oklahoma, and North Texas. The tests and analyses described were designed and adapted for use in the field in determining the relative corrosive and plugging tendencies of waters from various sources conditioned by different methods. Although the described methods were developed and used in testing oil-field waters in the Midcontinent oil-producing area of the United States, these same methods should be equally applicable to testing oil-field or highly mineralized waters throughout the world. Many of the methods used have been discussed by the writer (1)2/ previously, and some of them have been used for similar work in other laboratories. Early in the development of the practice of the subsurface injection of brines for disposal and increasing the recovery of oil, it became evident that different methods of chemical treatment and conditioning equipment would have to be devised to sustain desired injection rates into water-input wells. These changes became necessary because the highly mineralized waters produced with petroleum from deep formations became chemically unstable when pumped to the surface, owing to loss of dissolved gases as pressure and temperature dropped to atmospheric and to the contact with atmospheric oxygen at the surface.

Jan 1, 1954

By Donchak PJ, Lang SC, Hammond RL, Bultitude RJ

The Hodgkinson and Broken River Provinces form the northern part of the Tasman Orogen. They are separated by a broad belt of Late Palaeozoic igneous rocks, but were probably originally continuous. They are bounded to the west by a system of major faults (Fig. 1) which separate them from the Georgetown Province. Although largely Precambrian, the Georgetown Province includes probable Siluro- Devonian granitoids, and in the south adjacent to the Broken River Province, metamorphosed Early Palaeozoic(?) volcanics and sediments of the Greenvale Subprovince. South of the Broken River Province, the Lolworth-Ravenswood Province includes probable Precambrian rocks, Cambro-Ordovician volcanics and sediments, and voluminous Ordovician to Early Devonian granitoids. The first systematic studies of the provinces were the 1:250 000 scale mapping programs by the Bureau of Mineral Resources and Geological Survey of Queensland (White, 1965; de Keyser and Lucas, 1968). These and subsequent regional studies were reviewed by Arnold and Fawckner (1980). Remapping by the Geological Survey of Queensland since 1982, and a concurrent regional study of the deformation by Hammond (1986) have provided much new data. We acknowledge the contribution of other members of the GSQ field parties - L. Cranfield, J. Domagala, B.G. Fordham, P. Green, R. Halfpenny, R. Hegarty, L. Hutton, S. Law, D. Macansh, T. McLennan and M. Scott.

Jan 1, 1987

By C. K. Man

Coal dust explosions in underground coal mines are prevented by generous application of rock dust (usually limestone). If an explosion should occur, the rock dust disperses, mixes with the coal dust and prevents flame propagation by acting as a thermal inhibitor or heat sink. To investigate this process in more detail, a number of explosion experiments using various coal dust and limestone rock dust mixes have been carried out at the Lake Lynn Experimental Mine (LLEM). These were conducted in a single entry of about 1600 ft (488m) in length and initiated with a methane gas explosion. A consistent set of post-explosion floor dust samples were taken along the entry after each test. These dust samples have been analyzed in the laboratory using thermogravimetric analysis (TGA) and solubility to determine how the limestone rock dust behaved during the coal dust / rock dust explosions. The preliminary results are reported in this paper and indicate that the chemistry of limestone plays an important role in its capacity to inhibit coal dust explosions. The results also show that it may be possible to estimate the intensity of the explosion using these conventional methods of analysis. Disclaimer: The findings and conclusions in this report have not been formally disseminated by the National Institute for Occupational Safety and Health and should not be construed to represent any agency determination or policy.

Jan 1, 2009

Hydraulic mining shovels can be successively used at open-pit mining operation in severe climatic zone with air temperature interval from -700C to +450C typical for some northern region of the world particularly of Russia, Canada and Sweden, if they would be equipped by special preheating facilities for their diesel engine, water, hydraulic oil and lubrication systems. All shovels manufactured by the Komatsu Mining Germany GmbH for operation at ambient air temperatures down to -50¦C have cast and forged structural design elements, bolted connections made of special steel grades, electric cables with special insulation, flexible high-pressure hoses manufactured by ICE-Champion with connectors made of special steel grades.Generally at the temperatures below -25¦C the ordinary machine has to be stopped, the attachment should be placed in the parking position, the generator should be switched on, or the external electrical power supply connected, for the preheating equipment. For rapid start-up in winter after a long shutdown of a hydraulic shovel, there is a procedure for preheating of the main systems. It is applied for the following systems: engine cooling system, engine oil, hydraulic oil, pumps and drive motors of the propel gears, electric cabinets, machinery house, especially near the ventilation inlets and outlets.Start-up of the main drive engine is permitted at a hydraulic oil temperature of -20¦C, when it has a viscosity of 1000 cSt. In this case the rotation speed of the diesel engine crankshaft is lower by two times than the nominal value and this is the most favourable condition of start-up of the engine and hydraulic pumps and motors, which work with half of their rated rotation speed until the hydraulic oil reaches a viscosity from 100 to 10 cSt. After that the hydraulic system and the entire shovel begin to operate under normal conditions.

Dec 6, 2010

By M. G. Lipsett

"The Mining Information Technology User Group considers information to be a strategic enabler to improved business performance in mining. This ad hoc group has been meeting since 2000 to share knowledge and leverage their efforts in effectively using IT in mining. In this paper, core issues to mining IT are reviewed, along with initiatives to engage industry professionals and decision-makers in the potential for improved use of information in their operations. Relevance of IT to Canadian MiningMining operations always drive to improve their performance, and so far they have succeeded by using different technologies. While economies of scale have come in fragmentation and material handling, and energy usage has improved through conservation and design of integrated mineral processing plants, these systems have the net result of tightening operational constraints, through reduced excess capacity. There are higher opportunity costs of lost production when integrated, large-scale systems are operating in a sub-optimal way.The problem is that it is profoundly difficult to run a mine in an optimal way. Optimization requires a defined objective function (e.g., profit), which is hard to pose, let alone solve, because so many inter-related aspects of an operation affect the bottom line. Even for a small, well-defined process state, it is difficult to measure all the pertinent information with sufficient accuracy to ensure that the system is performing well in real time.The art of mining remains making good decisions with uncertainty: in the orebody delineation; in the allocation of resources; in the efficiency of the operation; in the reliability of components and systems; and in responding to the downstream market. As well, individual decision-makers need to know how their decisions affect other processes and systems, so that improvements in one part of an operation do not result in such degraded performance in the rest of the plant that overall profitability goes down."

Jan 1, 2003

By M. J. Hart

There are no formulas that guarantee success when it comes to obtaining zoning approval for mineral aggregate mining. Local land use decisions often times represent the most controversial issues faced by community. Public awareness, concern, willingness to get involved, sensitivity to the environment and probably most importantly fear of change only begin to describe the atmosphere in which local land use decisions are made. Add to this the public hearing process which is quasi judicial, adversarial, and unfortunately not designed for resolution of disputes and it is not difficult to see the need for an alternative to present methods. Hopefully, some day we will have a process that will do away with or at least minimize unnecessary, unproductive and unmanageable community conflicts.

Jan 1, 1984

By Shin-ya Kitamura

Kinetic modeling is very important to understand steelmaking reactions. The coupled reaction model proposed by Prof. D.G.C Robertson is the best suited program, and therefore, the author has applied it to the various steelmaking reactions, a few examples of which are discussed. Hot metal dephosphorization occurs under non-equilibrium conditions as it takes place between the slag, which has a high oxygen potential, and the hot metal, which has a low oxygen potential. A process simulation model based on the coupled reaction model was constructed. This model considers the solid and liquid slag, liquid metal phases, and the reaction between the solid and liquid slag, besides the reaction between the liquid slag and liquid metal. Using this model, the ruling factor to increase the reaction efficiency of dephosphorization has been verified. In the secondary refining process, the values of inclusion composition calculated by the thermodynamic model, under the assumption of equilibrium with the metal composition, were found to be different from those observed in practice. A kinetic model, incorporating the reactions between slag, metal, inclusion, and refractory has been postulated, and the composition change of inclusion during treatment has been analyzed.

Jan 1, 2014

By Ramon LaRusso, Frank Wheby, Richard Acker

Field investigations and office studies were used to develop criteria and cost parameters related to the geologic aspects of the proposed project. These results were employed in optimization of layouts and comparison of alternative schemes, leading to selection of the recommended program. Study of project features included the development of subsurface shafts, tunnels, and mined storage areas, and the utilization of existing surface quarries. These project features were proposed for construction within the bedrock units underlying Chicago. Principal geologic considerations included bedrock structure, stratigraphic sequence of units, rock competence and uniformity, and requirements for aquifer protection. All geologic factors were interrelated with other project considerations such as surface hydrology, hydraulics, and urban setting. Data for analyses was acquired through an exploration program conducted intermittently between 1967 and 1971, in addition to that already available through numerous explorations and well constructions in the project area. The exploration program included seismic surveying, core drilling, geophysical borehole logging, and water pressure testing of boreholes, and water well drilling and testing. Extensive laboratory tests were conducted on core samples. The data formed the basis of studies enabling the formulation of preliminary design and siting criteria resulting in construction cost evaluation.

Jan 1, 1997

By E. Topuz

This paper discusses factors affecting the productivity of continuous coal mining operations. It analyzes design and operational relationships in continuous mining systems, and investigates how their productivity can be improved by selecting the number of headings, the dimensions of pillars, and the depth of cuts as well as the miner loading rate and tramming speed, the shuttle car payload and hauling speed, and the roof bolting cycle time. A computer simulator has been found very efficient in analyzing effects of section layouts and equipment operating characteristics on the productivity of continuous coal mining systems.

Jan 1, 1987

By Terry J. Close

The Welcome Creek Wilderness has small, dispersed gold placers. Pockets in the 25.5 million yd3 (19.5 million m3) of alluvium along Welcome and Rock Creeks have as much as $5.61 gold/yd3 ($7.34/m3) at $500/troy oz ($16.08/g). All the alluvium averages 20.1 cents gold/yd3 (26.3 cents/m3). Because of the low average gold content large-scale placer mining would not be economically feasible. Small-scale selective pocket mining, however, may be profitable. The alluvium along the streams in the Wilderness has little apparent potential for production of sand, gravel, or stone because alternate sources are closer to markets. The four lode prospects known within the Wilderness appear to have low mineral potential. No oil, gas, uranium, or geothermal energy sources are known to be present.

Jan 1, 1982

By Thompson IR, Solomons SS

Underground mining with the cut and fill method has been declining during the past decade or so, being replaced mostly by sublevel open stoping methods. During 1983 the Australian Mineral Industries Research Association Ltd. (AMIRA) commissioned a review of the method, with the aim of compiling the state-of-the-art, indicating future trends and recommending topics for research that would be needed to support this future mining. Mines using the cut and fill method in Australia and three other countries were visited to compile current practices and expected developments.Cut and fill is mostly used where geological and ground conditions are unsuitable for open or caving methods. These range from narrow, irregular orebodies to wide, massive orebodies where pillars are retained in ore. There is significant potential for improvement and further development of the method. It may then be used in a broader range of conditions and for orebodies that may not otherwise be viable to mine.

Jan 1, 1985

By Alan G. Mayton

The Bureau of Mines conducted one of the most extensive studies on surface mine illumination to date, to assess the illumination needs of mobile surface mining machinery with respect to the visual tasks required of machinery operators. Field Investigations were performed at 22 surface mining operations, coal and metal-nonmetal, within several mining regions of the United States. Visibility and illumination were measured for 159 visual tasks performed by equipment operators on or near 57 surface mining machines, including draglines, shovels, blasthole drills, bulldozers, loaders, haul trucks, graders, scrapers, and several service-type vehicles.

Jan 1, 1987

By Varadarajan Seshadri

A physical model based on similarity principles was constructed for simulating the RH degasser of CST (Companhia Siderurgica Tubarao, Vitoria, ES, Brazil) to evaluate the circulation rate of the metal which essentially defines the degree of exposure of the metal to vacuum in the chamber and thus of the refining rate. The circulation rate on the other hand will influence the decarburization rate and removal of dissolved gases like nitrogen and hence it is essential to optimise this parameter to get maximum refining efficiency with minimum refming times, thus improving the productivity of the secondary refining process. Mixing characteristics in the ladle is evaluated by pulse tracer addition using conductivity-meters located at the down leg as well as at several locations in the ladle. The influence of gas injection through nozzles in the upleg with simultaneous bottom injection of gas as well as nozzle blockage on the circulation rates were investigated. Also simulation experiments of kinetics of decarburization were carried out using C02 adsorption-desorption process in sodium hydroxide solution as circulating fluid and the effect of, bottom gas flow rate in this case was also evaluated. The results were carried over to prototype and to optimize the process.

Jan 1, 2003