Search Documents

By A. K. Debnath

Mining being a site specific activity, land becomes the prime requirement for starting, successful execution and closure of any mining project. Many important mining projects are not progressing satisfactorily just because land is not easily available or environmental/social issues are not addressed properly. This is especially true in the case of open-pit mining, which requires large areas for mining, dumping of waste and additional land for other mine facilities. Mine closure & post mining land use exercises, though funded generously, may not achieve their objectives owing to uneven land profile after mineral extraction is over. One of the prominent solutions to these issues is application of steep angle conveyors in large open pit mines that will result in more space for internal waste dumping and enhanced slope stability of the dump. Additionally, such applications will result in economic extraction of mineral in deep open pits. Land reclamation exercise may start concurrently during early years of mine development as mineral evacuation is limited to a specific part of the mine. Surface mining facilities can also be advanced along with the pit by using modular/portable structures. The paper presented here attempts to address specific land related issues by developing suitable schemes and plans that can be practically implemented in open pit mines using advanced technology i.e. steep angle conveyors.

Aug 1, 2013

By Walter V. Knopp, Laurence Delisle

INTRODUCTION THE aim of this work was the preparation of nickel-steels from elemental metal powders by powder metallurgy techniques. It was known that plain carbon steels could be made from a mixture of iron powder and graphite and that the effect of carbon on iron in powder form was of the same nature as that produced in fusion metallurgy. The problem in making nickel steels from elemental powders consisted therefore in finding out whether sufficient diffusion of the nickel and other incidental metals normally present in such steels could be induced in the solid state to modify the properties of plain carbon steels made from powders and produce the beneficial effect of alloying. The composition selected originally was that of an S.A.E. 2330 steel. Metal powders, in the proportion corresponding to that composition, were mixed with graphite, pressed, and heated at different temperatures for different periods of time, to produce bonding of the metal particles and mutual diffusion of the various elements without melting. Temperatures up to 1325°C and sintering periods as long as 6 hr were first investigated because it was expected that such conditions would produce maximum diffusion with an accompanying improvement in the properties of the alloy. It was found that, although diffusion proceeded to a large extent under the conditions investigated, it would not be complete unless sintering were carried out at a high temperature for much longer than 6 hr. Relatively high temperatures and long sintering times are objectionable from a practical point of view, particularly when a low cost material is to be produced, because they necessitate the use of special, costly equipment. Work could be done to improve the diffusion of iron and nickel by changing conditions other than the sintering temperature and time, i.e., finer primary or alloy powders could be used. However, a marked change in the properties of the steel had been observed even with only partial diffusion. It was thought, therefore, that instead of trying to improve the diffusion, advantage might be taken of its incompleteness to produce a special structure consisting, in the unquenched condition, of a hard constituent, rich in nickel, dispersed in a tough pearlitic matrix. Steels with such a structure, not readily obtainable by fusion, should have desirable mechanical properties. Besides, it should be possible to prepare them from elemental powders under economical conditions. This latter alternative was therefore adopted for the second phase of this work. This report is divided into four parts: 1. General Procedure. 2. Effect of Sintering Temperature. 3. Effect of Varying the Nickel Content. 4. Effect of Alloying Elements. GENERAL PROCEDURE The general technique of cold pressing as used in powder metallurgy was applied.

Jan 1, 1948

By J. G. Schoning

The Holmes Safety Association is an offspring of the Joseph A. Holmes Safety Association which was organized in Washington, D. C., in 1916 at a meeting of representatives of twenty-four leading mining associations connected with every branch of the United States mineral industries. The purpose of the meeting was to do honor to the memory of Joseph A. Holmes, one of the founders of the United States Bureau of Mines and its first director, whose death had occurred the year before on July 12, 1915. In deference to what was believed would have been the expressed wish of this great humanitarian and benefactor of the mineral industries, it was decided to establish a national safety organization to cover the mineral indus¬tries exclusively; out of respect for his memory and service, the organization was named the Joseph A. Holmes Safety Association. On receiving requests from several mining districts, in 1922 a number of chapters ware established in several mining States.

Jan 1, 1929

By V. C. Wansbrough

A LUCID, thorough and powerful review of the impact of your tax laws on mining operations has already been presented by Granville S. Borden*. He has brought into focus and relief the pressure-points at which the shoe pinches most, has suggested some remedial measures, and enunciated much sound doctrine about the interrelationship and interplay of taxation policy and mining activity. Under the heading "What Every Lawmaker Should Know", he laid down the fundamental proposition that "the magnitude of our mineral resources varies inversely with the magnitude of the taxes levied upon them." With this, as with his other major premises, all mining men must be in hearty concurrence. There can be no doubt that a flourishing and expansive future for the mining industry in this country, in Canada, or anywhere else will depend on the thoroughness with .which these fundamental propositions are grasped by legislators, by national policy-makers and by public opinion at large.

Jan 1, 1950

By Brian Stump, Rong-Mao Zhou

A series of single-fired (simultaneously detonated) explosions were conducted in an Arizona copper mine. The explosions spanned yields from 1700 to 13600 lbs (773 to 6169 kg) and were all detonated in an approximate 100 m by 100 m area. In order to quantify the effect of the mine free-face, the individual explosions were also detonated under three different emplacement conditions including at the free-face of the mine under normal burden, twice normal burden and fully contained. The purposes of these experiments were to investigate: (1) Generation of in-mine and regional phases such as Pg, Pn, and Lg from mining explosions; (2) Quantification of the relationship between yield and seismic amplitudes; (3) Quantification of the effect of confinement; and (4) Similarities and differences between single-fired waveforms and those from delay-fired explosions. Instrumentation was deployed at near-source (100-700 m) and in mine (1-5km) distances. Empirical scaling relations for the different shots in this test series were developed in order to quantify the effects of yield and confinement.

Jan 1, 2006

By J. E. Murphy

A method is being developed by the Federal Bureau of Mines for recovering lead metal from galena without the generation of SO2. Lead chloride is obtained by leaching lead concentrate at a temperature of approximately 100° C with FeCl3 solution: PbS + 2FeCl. " PbC1 2 + 2FeC1 2 + S. Electrolysis of the PbCI 2 product in a fused-salt bath results in deposition of molten lead metal at the cathode and evolution of chlorine at the anode. The chlorine can then be absorbed in the spent leach solution to regenerate FeCl3 for recycling. Optimum electrolyte composition was a PbC12-LiCl eutectic containing 7.6 wt-pct LiCl. The PbCl2-NaCl eutectic also proved satisfactory. Electrolysis in the PbCl2-LiCl bath at 450° C yielded 99 pct current efficiency at a current density of 5 amp/in2 with an energy requirement of only 0.24 kW-hr/lb metal produced. This compares with 98 pct current effi¬ciency and 0.26 kW-hr/lb metal produced for the PbCI2-NaCI bath. A typical lead deposit contained less than 100 ppm total detectable metallic impurities. At the low temperature employed for electrolysis, there was essentially no vaporization of Pb or FbC12.

Jan 1, 1974

By Jean Robitaille

La découverte du gisement du puits Penna a nécessité une révision complète de tous les circuits du concentrateur Laronde pour permettre, premièrement, l?adaptation du procédé à la nouvelle minéralogie et deuxièmement, l'accroissement du tonnage de 1800* à 4500 t/j. Aux circuits existants de broyage, de flottation du cuivre, de cyanuration et du charbon en pulpe, les circuits suivants furent greffés : broyage semi-autogène, flottation du zinc, manutention des concentrés (épaississage, filtration, entreposage et chargement automatisé), décantation à contrecourant et précipitation au zinc, destruction des cyanures et remblai en pâte. Cet article se veut une revue des différentes étapes du projet d'agrandissement du concentrateur qui se sont effectuées par phases progressives de 1997 à 2000. De plus, une description des nouvelles technologies sélectionnées et implantées est présentée.

May 1, 2001

By Kenneth L. Cook

From March 1944 to July 1945 the Division of Geophysical Exploration of the Federal Bureau of Mines made magnetometer surveys of some of the principal iron ore deposits of the Iron Springs district, Iron County, Utah. The district comprises a belt about 23 miles long and 3 miles wide. Most of the large ore bodies are found as pods of replacement ore within a favorable limestone bed lying at the margins of three separate igneous intrusions in the district The magnetic surveys were confined chiefly to this geologically favorable zone at the margins. The iron ore is a mixture of magnetite and hematite. The magnetite content of the ore ranges from 14 to 58 percent. Magnetic anomalies of 1,250 gammas or more were usually found over the near-surface ore bodies. About 62,000 magnetometer stations were taken over a total traverse distance of about 300 miles. Outcropping ore bodies were surveyed to determine, insofar as was possible from the magnetic data, their probable length, width, depth, extent, strike, dip, and tonnage. Geologically favorable areas where no ore is exposed were explored in an endeavor to find new ore bodies. Favorable locations were determined for exploratory diamond drilling, both in areas of exposed ore bodies and in areas of newly discovered magnetic anomalies. Forty-five separate magnetic anomalies that indicate the possible existence of ore bodies were observed. Of these, 13 anomalies are caused by outcropping ore bodies of proved commercial size. Five are caused by non-outcropping ore bodies of proved commercial size which were discovered, in whole or in part, as a result of the geophysical surveys. Of the remaining anomalies, which lie in virtually un-tested areas where few or no ore bodies are exposed, six probably are caused by large, unexposed replacement ore bodies, nine are possibly caused by large, unexposed replacement ore bodies, and six are probably caused by unexposed magnetite veins of some small commercial importance,

Jan 1, 1949

By Toro HCH, Von Borries GH

A brief description of the semi-autogenous grinding (SAG;) facilities of Compania Minera Disputada de Las Condes is given. A data-logging and computer system was connected to the plant inter facing the existing analog control system in a supervisory s, control philosophy. The development of a control straiov,v t,) maintain maximum power of the SAG mill atsubjected to process restrictions is shownThe present control scheme is discussed inalgorithm was designed based on correlations onLween vartaoles. Associated with this, a direct level of control was developed be, on classical control algorithms, process inter-active tuning has been included. Also, an algorithm to prevent overloading of the is discussed. Control scheme tests are presented in comparison t manual operator control under the same conditions. It is shown t the control strategy gives a more stable operation and a higher plant throughput.

Jan 1, 1985

By A. Patti, S. Reutzel, D. M. Herlach, L. Ratke, I. Egry

Cu-Co shows a metastable miscibility gap in the region of the undercooled melt. Undercooling of the melt below the binodal leads to separation of the melt into a Co-rich LI-phase and a Curich L2-phase. Experimentally, undercooling into the metastable miscibility gap is realised by means of electromagnetic levitation (EML), processing in drop tube (DT) and by melt flux embedding. As undercooling is large in these experiments, the velocity of the solidification front is high and the microstructure is frozen in instantaneously. Samples have been undercooled and solidified in the TEMPUS-facility (container less electromagnetic processing under weightlessness) during parabolic flight under reduced gravity conditions. Microstructures of solidified samples have been analysed and compared to those processed under gravitational conditions. The influence of convection on phase growth is much lower in reduced gravity. The microstructure shows spherical droplets of the minority phase, statistically dispersed in the majority phase.

Jan 1, 2004

By Carl W. Kelley

PRODUCTION in the United States of carbon black has increased from 20 million pounds per year in 1920 to over 2 billion pounds in 1964 valued at $156 million, mostly for consumption by the rubber-tire industry, which uses over 90 percent of total production. Production of over 2 billion pounds in 1964 is a 7.8-percent increase over 1963 and is the first time furnace black production has topped 2 billion pounds. Although 1964 channel black production dropped 6 percent below 1963, carbon black produced by the furnace process, which ac-counted for 92 percent of total production, increased 9 percent to 2,053 million pounds. Total shipments during 1964 amounted to 2,245 mil-lion pounds, a 7 percent increase. This growth parallels the expansion of the automotive and petroleum industries. Along with this expansion have been many advances, both in methods of manufacture and in the quality and variety of blacks available to industry. There are several kinds of carbon black, thermal, channel, furnace, lamp, and oil blacks. Until recently, channel has been the important black in rubber compounding. Following the introduction of the synthetic GR-S, and more recently of "cold rubber," it has been found that certain furnace blacks with particle size larger than that of the standard channel black give superior reinforcement. A great advantage of furnace black is that its yield per unit of gas feedstock is higher than that of channel black. The 184-million-pound increase in domestic carbon black sales was partially offset by a 37-million-pound decrease in exports. Decrease in exports especially to Europe, is expected to continue. In Europe, as in the United States, the major end use for carbon black is in the manufacture of automobile and truck tires. Although the number of automobiles in Europe is predicted to grow by about 7.5 percent per year, compounded until 1975, the increased demand will be met by a 20 percent increase in existing capacity and by the new plants being built in Europe by U.S. companies. Also) aromatic oils for producing furnace blacks are plentiful now that western Europe's chemical industry is switching to a petroleum base.

Jan 1, 1965

By K. Fuenkajorn, S. Serata

Discussion by S. Serata and K. Fuenkajorn Background Results of the above study in the August 1991 issue of Mining Engineering offer valuable lessons in the solution of cutter-roof problems. The original study plan was initiated by the discussion authors to solve the problems using the "stress control method" of mining (Serata 1976, 1982; Serata, Carr and Martin, 1984; Serata and Gardner, 1986; Serata, Gardner and Preston, 1986; Serata, Gardnerand Shrinivasan, 1986; Serata and Kikuchi, 1986; Serata, Preston and Galagoda, 1987) However, the plan and the planner were changed to the arrangement reported in the paper. The change was considered reasonable at the time due to the mine engineers' uncertainties about the stress control method. Consequently, the basic principle of the study was shifted from the original stress control method to the method described in the paper, which will be called the "yield pillar method" for the purposes of this discussion. The paper convinces the reader that the yield pillar method fails to solve the cutter-roof problems. This doesn't mean that the stress control method also fails. Actually the contrary is true, as discussed below. Limitation of the yield pillar method The paper illustrates clearly how poorly the yield pillar method performs in solving the problem. The reason for this failure is the lack of the protective stress envelope needed to stabilize the cutter roof. Unfortunately, the protective envelope cannot be formed properly without utilizing the stress control method of mining. Changing the pillar size does not make much difference in the roof stability. Stress measurement The key issue is how to form the global stress envelope to make the gate entries safe for production. Therefore, measuring the stress condition of the ground around the mine opening is critically important to solving the cutter-roof problem, regardless of the method applied. With regard to the stress measurement, there is a serious question as to the reported stress state of [6 i = -51.7 MPa (-7499 psi), G2 = -44.5 MPa (-6458 psi) and 63 = -30.8 MPa (-4465 psi)]. It is mechanically impossible to have such a stress state at any location in the mine ground since the known initial vertical stress [o,,] is less than or equal to 800 psi. There may be a large stress state in the [61] direction, but that is possible only at the expense of the [63] value. Having the above stress tensors in the mine is simply impossible. The questionable, reported stress values could be attributed to the application of the overcoring method, which tends to produce erroneously large stress values in the extremely nonelastic mine ground. Stress control method The paper should be considered as a major contribution demonstrating the limitation of the yield pillar method. At the same time, the paper does not disprove the stress control method. However, in comparing the paper with stress control studies conducted in other similar failing grounds, the stress control method appears to be able to solve the problem more effectively. Therefore it is advisable that the mine not give up its efforts to solve the problem. [•] References Serata, S., 1976, "Stress control technique - An alternative to roof bolting?," Mining Engineering, May. Serata, S., 1982, "Stress control methods: Quantitative approach to stabilizing mine openings in weak ground," Proceedings, 1st International Conference on Stability in Underground Mining, Vancouver, BC, Aug. 16-18. Serata, S., Carr, F., and Martin, E., 1984, "Stress control method applied to stabilization of underground coal mine openings," Proceedings, 25th US Symposium on Rock Mechanics, Northwestern University, June, pp. 583-590. Serata, S., and Gardner, B.H., 1986, "Benefits of the stress control method," invited paper, American Mining Congress Coal Convention, Pittsburgh, PA, May 7. Serata, S., Gardner, B.H., and Shrinivasan, K., 1986, "Integrated instrumentation method of stress state, material property and deformation measurement for stress control method of mining," invited paper, 5th Conference on Ground Control in Mining, West Virginia University, Morgantown, WV, June 11-13. Serata, S., and Kikuchi, S., 1986, "A diametral deformation method for in situ stress and rock property measurement," International Journal of Mining and Geological Engineering, Vol. 4, pp. 15-38. Serata, S., Preston, M., and Galagoda, H.M., 1987, "Integration of finite element analysis and field instrumentation for application of the stress control method in underground coal mining," Proceedings, 28th US Symposium on Rock Mechanics, Tucson, AZ, pp. 265-272.

Jan 1, 1993

By Henrique Silva Furtado

Light meter is an ArcelorMittal innovation that uses off-gas light intensity to predict bath carbon, which is akin to the visual cues that the operators employ to finish a blow. Light meter enables the prediction of end point that is independent of any operator’s judgment. The results have been in general consistent with the actual carbon content at BOF end point at Tubarão. Besides some outliers that occurred due to strange intensity curves, the system implemented in Tubarão BOF 3 reported a carbon prediction error statistic that is very similar to dissolved oxygen–carbon end point statistics. Preliminary trials using light meter without any filter improved carbon hit ratio significantly.

Jul 30, 2018

By P. M. Kelly, E. P. Butler

The stability of a 70/30 Mn-Cu alloy aged to peak damping has been investigated using electron microscopy, X-ray diffraction, and torsional pendulum measurements. Storage at room temperature or at 100" C causes a reduction in damping capacity. This is shown to be due to the formation of subdomains which "lock" the main domain structure and so hinder their movement. After storage the damping capacity can be restored by a retransformation treatment, which generates structures identical to those found in newly aged specimens. Plastic deformation by rolling also causes a decrease in damping capacity. In this case the damping capacity can only be restored by retransformation if the amount of deformation is less than about 5 pct. THE general metallography and structure of these high damping capacity alloys has been discussed in Part I of this work.1 Part II deals with some of the variables that affect the damping capacity. In particular, the stability of the damping capacity of a 70/30 alloy aged for 2 hr at 425° C and quenched has been investigated. The temperature sensitivity of the damping capacity of a 70/30 alloy aged for 2 hr at 450° C has been reported by Birchon.2 The damping capacity begins to decrease with increasing temperature, and is very low above the M, temperature of 125°C. The cubic — tetragonal transformation is completely reversible and there is no apparent thermal hysteresis associated with the change in damping capacity. Another important effect was first reported by Dean and his coworkers.3 They noticed a decrease in the damping capacity with time for specimens of a quenched tetragonal alloy. More recently workers at the Admiralty Materials Laboratory 4 have studied the stability of an aged 70/30 alloy. They found that the damping capacity decreased to half its original value after about 1000 hr at room temperature. EXPERIMENTAL The techniques used for electron microscopy and X-ray diffraction have been described in Part I. The damping capacity was measured by means of a torsional pendulum, using rectangular specimens, 3 by 0.3 mm with a 6 cm gage length. The specific damping capacity, S.D.C., was calculated as a percent amplitude decay in free vibrations over 10 cycles, starting at an amplitude which corresponded to a 700 psi surface shear stress. Because of the stress dependence of the damping,' the values obtained were about a third those reported for a 5000 psi surface shear stress.' RESULTS a) Effect of Aging Temperature. The effect of aging temperature on the damping capacity is shown in Fig. 1. The damping capacity reaches a peak of 12 pct after aging at 400° to 425°C) then begins to decrease as the volume fraction of a Mn increases. At higher aging temperatures the structure becomes cubic again with a low damping capacity. b) Stability of the Aged Structure. The damping capacity of the aged alloy decreases with time at room temperature. This process could be accelerated by storing at 100°C, when about 100 hr were required for the damping to fall to half its original value. The results of room temperature and 100°C storage, for times up to 1000 hr, are shown in Fig. 2. The damping capacity starts to decrease after about 24 hr at 18° C and 1 to 2 hr at 100°C. It was found, however, that the damping could be almost completely restored by retransformation. The specimens were held at a temperature above the M, for a short time, 250° C for 5 min, and then quenched. The values of damping capacity for specimens that were aged, stored, and then retransformed are shown by the full points in Fig. 2. X-ray measurements of the c/a ratio and hardness readings on the specimens did

Jan 1, 1969

By J. A. Marts, R. C. Gilmore, Jr. Bogin, S. A. Saki, J. F. Brune, J. W. Grubb

"Colorado School of MinesResearchers at Colorado School of Mines (CSM) have developed computational fluid dynamic (CFD) models to study gas distributions and explosion and fire hazards in longwall gobs. In underground coal mines, methane continuously emitted from surrounding strata mixes with air from active mine workings and may form explosive gas zones (EGZs). Some western United States coal mines are also prone to spontaneous combustion (spon com). Insight into oxygen concentrations within the gob is crucial for assessing spon com hazards and mitigation strategies. Nitrogen injection used in conjunction with progressive gob sealing can reduce EGZs and spon com hazards by forming a dynamic seal that separates the methane in the gob from the air that ingresses from the face. This paper describes CFD modeling simulations studying the formation of such dynamic seals by optimizing the nitrogen injection locations. The impact of nitrogen on oxygen ingress and formation of EGZs is discussed. Optimum nitrogen injection quantities and injection locations were determined. Dynamic seal formation is most effective if the headgate nitrogen injection locations are split between the first crosscut inby the face and a second location about 300 m (1,000 ft) further inby. INTRODUCTION Underground longwall coal mine ventilation systems are designed to dilute hazardous gases and to provide breathable air to miners working in the area. Methane gas is liberated as the mining process extracts the coal and disturbs the surrounding strata. Methane mixes with the ventilation air and often produces explosive gas zones (EGZs) within longwall gobs (Brune 2013). Past CFD modeling research of underground coal mine ventilation systems has shown the effects of face air quantity on EGZs (Worrall 2012) and nitrogen injection to control spon com (Balusu et al. 2005; Ren et al. 2012; Ren et al. 2011; Smith and Yuan, 2008; Yuan and Smith, 2014). Other modeling approaches include network ventilation models of oxygen ingress (Dziurzynski and Wasilewski, 2012), and coupled Linear Network CFD algorithms (Wedding 2014). In a project sponsored by the National Institute for Occupational Safety and Health (NIOSH), CSM researchers are using Fluent®, a CFD software package by ANSYS, Inc., to model gas compositions and flows in underground longwall gobs. Figure 1 shows a progressively sealed gob with a U-type ventilation system in a three entry development. As the longwall advances, seals are constructed along the headgate in the crosscuts between the center entry and the gob. Additional gob isolation seals are built to block off the headgate entries inby the face. Nitrogen is injected through the seals in the first two crosscuts on the headgate side and at the first crosscut inby the face on the tailgate side, as shown in Figure 1."

Jan 1, 2015

1. Recent publication Iron and steel works of the world. Worcester Park (England), Metal Bulletin PLC, 1987. 9th edition, 728 pp. £94.75 by air mail.2. Canadian publications Mining and mineral processing operations in Canada, 1987. Mineral Bulletin MR 216. $15. (Obtainable from Printing and Publishing, Supply and Services Canada, Hull, Quebec, KIA 059 Canada.) Peat producers in Canada, 1986 directory, by M. Prud'homme. MRI 87/7 Canadian mines: Perspective from 1986. Reserves, production capability, exploration, development. Mineral Buletin MR 215. $9.95. 3. Mintek publications Report M313 The testing of abrasion resistance in pipeline materials, by D.P. Enright. Nov. 1987. 36 pp. Report M328 The installation and commissioning of a Hilger Monospek D500 scanning monochromator, by A.E. Watson. Sep. 1987. 11 pp. Report M331 The design and operation of hot-air dryers for the drying of granular activated carbon. Nov. 1987. 30 pp. Report M338 Ore microscopy, image analysis, and the extractive metallurgy of sulphide minerals-an overview. Nov. 1987. 14 pp. Report M339 The determination, by flow-injection analysis, of sulphate in solutions containing chromium(I/I) and iron(I/I). Nov. 1987. 11 pp. Report M222D The simultaneous determination of common anions by ion chromatography, by A. Cameron and C. Pohlandt. Oct. 1985, reissued May 1987. 10 pp. Report M227D The spectrophotometric determination of silica in metallurgical-grade fluorspar, by M. Solomons. Nov. 1985, reissued Jun. 1987. 9 pp. Report M229D The determination of metalic iron in prereduced iron ores, by R. Lownsbrough. Dec. 1985, reissued Jun. 1987. 7 pp. Report M252D The spectrophotometric determination of bismuth in sulphide materials, by M. Solomons. Mar. 1986, reissued Jun. 1987. 13 pp. Special Publication no. 12 Platinum in South Africa, by A.M. Edwards and Silk. 1987. 64 pp. Illustrated in colour. R30 ( Africa), US$30 (other countries). 4. Journals of interest Industrial Minerals. London, Metal Bulletin Journals Ltd. Tin and its uses no. 154, Nov. 1987.

Jan 1, 1988

By T. C. Rao, Vanangamudi. M., J. P. Barnwal

Experiments were carried out on 76 mm laboratory heavy medium cyclone treating -2.0 t 0.5 mm coal and on two 600 mm industrial heavy medium cyclones treating coal in the size range -13.0 t 0.5 mm. The variables studied were spigot diameter and feed medium gravity. The generalised distribution curve for the separation of coal in these heavy medium cyclones has been defined by the equation [ ] The specific gravity of separation SG has been found to increase linearly with increase in feed medium, gravity (SGf). The relationship for SG of industrial cyclone is given as 50 SG = -6.801 t 6.463 SGf t 0.0327 Spig 50 -0.02625 SGf. Spig. Further, the probable error for the separation has been found to be linearly related to (SG50 - SGf ) according to the equation [ ] The model equations developed have been used to select appropriate levels of operating conditions to achieve an increase in the yield by about 2 to 4% without affecting the quality of the product.

Jan 1, 1990

By N. P. Pinto

Compacting below the recrystallization temperature was studied. Ideal density was attained at 550° to 600°C using 25 tsi. Compacts have strength and hardness higher than cold worked beryllium. The recrystallization temperature of this highly stressed metal is that of cast, cold worked beryllium and appears independent of pressing temperature. THE process metallurgy of beryllium is beset by many difficulties that hinder the production of sound beryllium shapes of controlled properties. Most of these obstacles are traceable directly to the low density, low ductility, and high affinity for oxygen of the metal. Castings are susceptible to cracking and porosity, and controlled grain size is not easily attained, yet is critical to further working. Any process must carefully avoid oxygen pickup. Conventional metallurgical processes, including melting, casting, forging, rolling, and extruding have been treated previously,'" as have the conventional powder metallurgical methods.' More recently, a method has been advanced for producing powder compacts of high density by hot pressing at 1000" to 1100°C, using pressures of 0.25 to 0.5 tons per sq in. (tsi).3 Here, Seybolt and coworkers attained theoretical density of 1.85 grams per cc using pres-sure-temperature combinations of 500 psi-1100°C, 750 psi-1075"C, and higher. The warm pressing of beryllium is a practical method for producing bars of controlled properties and appears to have certain advantages, particularly when high strength and hardness are required. Other investigators have studied the hot pressing of various pure metals, such as copper,"-" gold," iron,10-11 and aluminum." Their results indicate that ideal densities may be attained by compacting at temperatures less than 50 pct of the absolute melt-

Jan 1, 1955

By Bartho J. Admiraal, Antoine Feddema

Pneumatic sinking of caissons has been established from mid-19th century. The technique of pneumatic sinking has been applied on many projects for underground construction up to depths over 20m below groundwater level since that time. Volker Staal en Funderingen, a known deep foundation contractor in the Netherlands, was awarded two contracts in 2015 for sinking in total 2 caissons in Hamburg (Germany) to large depths (over 30 m (100 ft) and two projects near Amsterdam (the Netherlands). The latter concerned two gate chambers for the world’s largest sea-lock, one of them was 55x81 m2 (180x266 ft) to a depth of 25.5 m (84 ft), which would mean a world record for pneumatic sinking! But with depths and dimensions like these, the deployment of personnel is the main limiting factor for production, despite all developments to date. It was decided to develop a remote controlled process, including the necessary equipment and monitoring systems. Monitoring not only the kinematics of the equipment in the working chamber and the production parameters related to the excavation but also of the structural behaviour of the sea-lock gate chambers was essential for approval of this innovative execution method. The lay-out and the sizes of the largest caisson the structural integrity was extremely critical for torsion and bending moments. A displacement controlled execution by the observational method was therefore required. In engineering a new approach for modelling the semi-continuous failure mechanisms of the soil was needed to understand the sensitivity of the excavation process and to define limit values for the execution. In the paper these structural and geotechnical issues will be explained together with the experiences during the execution.

May 1, 2022

By L. Jones, S. R. Lawrence, A. R. Holloway

Whilst dense medium separation is best known for its ability to concentrate diamond and coal deposits, the process is now being employed in southern Africa as a pre-concentration step to improve the economics of platinum group metal and nickel ores. DMS plants built for these industries (such as the 1600tph unit at Tati Nickel, Botswana), are spearheading an expansion in this area by reducing mine and process operating costs yet maintaining economic metal recoveries. This paper provides an overview of DMS technology and examines the economic benefits available to North American operators and projects, with recent case studies as reference.

Jan 1, 2009