Search Documents

By Charles H. Wells

This paper describes a commercial installation of a sophisticated instrumentation and control system designed to maximize the performance of heavy medium cyclones. Samples of plant feed and its products were collected and analyzed for ash content so that measures of efficiency could be determined for plant operation under (1) manual control and (2) automatic (computer) control. The heavy medium cyclone control strategy and its digital computer implementation are discussed in detail. The sample results are analyzed and the economic benefits of automatic control are discussed. Results from the initial data sets quantify the economic benefits of automatic closed-loop control; viz, increased recovery and reduced clean coal variability have been clearly demonstrated.

Jan 1, 1981

By d&apos, L. Berenbaum, F. Heurle, R. Rosenberg

The structure of aluminum films obtained by evaporation was studied by electron microscopy, mostly by replica techniques and X-ray diffraction. The resistivities and stress conditions of the films were also determined. Film properties were studied as a function of source selection, substrate type, residual pressures of oxygen and water vapor, substrate temperature, and rate of growth. The formation of abnormal localized growths and whiskers resulting from annealing treatment subsequent to deposition was investigated. Films deposited onto single-crystal substrates were found to be epitaxially 0riented; for such films, relative orientations between films and substrates were determined. ALTHOUGH wide use has been made of evaporated aluminum films for the formation of conducting lines on semiconductor devices, relatively little has been reported concerning the structural characteristics of such films.1"9 The purpose of this study was to obtain an overall view of the dependence of these characteristics on film deposition and subsequent annealing conditions, which were similar to those used in silicon planar technology. Accordingly, most of this study was carried out using oxidized and bare silicon wafers as substrates, although some work was also done using alkali halide, magnesium oxide, and mica substrates. However, the main concern remained pragmatic. Emphasis was given to the study of the effects of deposition and annealing conditions on film characteristics such as structure, resistivity, and stress. I) EXPERIMENTAL PROCEDURES The films which were investigated in this study were deposited in 18-in.-diam glass chambers which were connected to the usual type of trapped diffusion pumps filled with silicon oil. Through the use of liquid-nitrogen-cooled Meisner traps and titanium sublimation pumps placed inside the deposition chambers, the pressure could be lowered to the lower portion of the 10- I Torr range and little increase in pressure would occur during the deposition cycle. Unless described otherwise, the substrates were 1-in.-diam p-type silicon wafers having a resistivity of 10 ohm-cm. The wafers were oxidized in wet oxygen at 975°C followed by a short dry-oxygen exposure at the same tempertture to a total oxide thickness of approximately 6000A. The wafers, backed by a layer of gallium, were mounted onto molybdenum discs brazed to a copper block.10 The latter was heated by imbedded commercial cartridge heaters. The substrate temperature could be maintained to within +10°C of a prescribed temperature during film deposition. The search for a satisfactory source for the controlled evaporation of aluminum has led to the use of 1-in.-diam crucibles" machined from rods of a commercially available, refractory composite* of Bn and

Jan 1, 1969

By H. Billmayer

This report covers the period from June 17, 1974 to February 20, 1975, and describes the work performed in compliance with the requirements of Contract No. H0346102 and Modification No. 1 thereto. The purpose of the contract was to design protective canopies for an Elkhorn Scoop, a Lee Norse Miner, a Wilcox Miner and a Wilcox Bolter; to construct mockups of the canopies; and to obtain machine operator evaluations of the canopy designs by assessing the mockups while installed on their machines in the mines. The overall program objective was to achieve protective canopy designs for the four machines which would be acceptable to the operators.

Jan 1, 1975

By J. Fuller, J. Beale, Q. Justice, Z. Agioutantis, S. Hicks, Z. Khademian

Seismic events can be induced by mining due to unstable rock failures or slips along geologic structures leading to the sudden release of strain energy stored within the rock near underground openings. Depending on their intensity and proximity to the working area, seismic events may raise safety concerns, and thus the forecasting of the seismic potential in advance of mining can mitigate safety hazards. The integration of seismic data into geomechanical modeling can provide a tool for identifying areas with elevated potential for seismic activity. In previous works, a methodology was developed to forecast seismic potentials in a pseudo-2D geomechanical model. In this paper, seismic events, ranging in magnitude from about -1.0 ML to 3.7 ML, recorded in a deep longwall mine (> 450 m) in Virginia during mining of six adjacent panels, were evaluated to identify areas where larger magnitude events (> 1 ML) had occurred. A three-dimensional geomechanical model of the same area was constructed in the 3DEC software to calculate the state of energy in the system with the progress of mining along the entire length of each panel. The variation in the energy content of the model was monitored, and zones with potentially damaging slip-type events along bedding planes followed by compressive-type events in the sandstone roof are the mechanism for large seismic events in the studied mine. The locations of anomalous events corresponded to the regions where both compression-type SPI (C-SPI) and slip-type SPI (S-SPI) were elevated. The modeling results were compared with the recorded seismic events to evaluate the model performance in forecasting the seismic potentials. The model was able to forecast 100% of regions with elevated and moderate seismic potential and 89% of regions with low seismic potential. This shows the applicability of energy balance calculations for forecasting the approximate location and timing of destructive seismic events in advance of mining.

Jun 25, 2024

PRESIDENT BOTTOMLEY: Gentlemen, the next order of business, if you wish to discuss it is Mechanical Loading. We still have a little time left that could be devoted to that subject, and the meeting will be open now for that purpose. Where is Mr. Edge- worth? J. E. EDGEWORTH (Foreman, Union Pacific Coal Company, Rock Springs, Wyoming): Here. PRESIDENT BOTTOMLEY: Yon start the ball rolling. Tell us what you are doing in the Rock Springs District, on the mechanical loading. SECRETARY SHURART Mr. Edgeworth is the man at the face handling the coal. He never sees the light of day these late winter mornings.

Jan 1, 1927

By Jim A. King

The total pressure oxidation of copper concentrates is a potentially viable option for treating copper concentrates that are either low grade or contain significant impurities. Both concentrate types are heavily penalized in smelter contracts. The total pressure oxidation process involves autoclaving the copper concentrate at temperatures of 200-220 C under oxygen pressure. The autoclave discharge can be separated into a solid (oxidation residue) and a liquid (oxidation solution) product. The oxidation solution can be treated for copper recovery by solvent extraction - electrowinning or by direct electrowinning. The direct electrowinning recovery of copper requires prior removal of selenium and tellurium by cementation on finely divided scrap copper. The oxidation residue is washed thoroughly to remove acid and dissolved copper prior to precious metals recovery by conventional cyanidation in the presence of lime. The results of a benchscale investigation involving a number of copper concentrates are reported. Copper recoveries in autoclave oxidation and gold recoveries by cyanidation of the oxidation residue exceeded 99%. The results of benchscale experiments to demonstrate copper recovery are described. Various flowsheet options are presented.

Jan 1, 1993

By Chris Kelly

The Monroe County Quarry is an open pit granite quarry located near the town of Bolingbroke. Monroe County. Georgia. The quarry has been in continuous operation for approximately 10 years. The quarry covers approximately 27 acres and has an annual production rate of 1.0 million tons. On the morning of April 26. 2000 a sudden rapid highwall failure occurred at the west end of the north wall of the quarry pit. The failure occurred approximately one hour after a three inch-wide crack was observed in an access road located at the crest of the highwall. No indications of failure had been observed prior to the development of the crack. The active mining area had been at the base of the failed area. The pit was successfully evacuated prior to the failure and there were no losses of either personnel or equipment. The amount of failed material was estimated to be in excess of two million tons. In order to ensure a safe working environment at the quarry a slope monitoring program was established in the area of the failure. The program consisted of using an EDM survey instrument to periodically measure the location of survey prisms installed at carious points on the north wall. The locations of the prisms were recorded over several months and changes in location were analyzed in order to identify and characterize the movement of the failed mass. The results of the analysis provided a basis for recommendations regarding access to various areas of the quarry. This paper discusses the factors contributing to the failure, the method of post-failure slope monitoring, anti the interpretation of the monitoring data.

Jan 1, 2002

By J. George Gregr

"This paper gives a brief review of grinding mills installation procedures with special emphasis on future maintenance. The importance of cooperation between the customer, construction contractor and manufacturer's representative is discussed, as well as the imparlance of complying with standards, specifications and the keeping comprehensive installation records.Fundamentals of mill maintenance are explained with the aim being to maximize the equipment availability and to minimize unscheduled downtime. The paper also includes development of wear items design, based on operating conditions, drive components and bearings, and how to keep large gears healthy thus eliminating surprise failures.Experience with installation of a large gear on a 34-foot diameter mill in Lornex and successful application of a computer program for the gear alignment on the mill are given.IntroductionSuccessful operation of a concentrator begins with the engineering of the project and continues through selecting the right equipment, its installation , start-up period, and ends with final tuning of the process. machinery and the human factor into an efficient and viable industrial complex.The following is a brief review of grinding mill installation procedures with special emphasis on future maintenance. Fundamentals of mill maintenance are discussed with the aim being to maximize the equipment availability and to minimize unscheduled downtime, with some specific points on key grinding mill components such as bearings and drives.Finally, the experience is recounted with the installation of a large ring gear on a 34-foot diameter mill at Lornex, and the successful application of a computer program for the gear alignment on the mill."

Jan 1, 1985

By Cloyd M. Smith

A few years ago, the Ventilation Committee established the practice of resenting one topic each year for discussion at the annual meeting. The practice has met good response on the part of committee members and I suggest that it be continued. The topic chosen for this year, "Underground Anemometry," is a topic which has bothered me for more than 20 years. It seems to me that the coal industry is content to rely on slipshod methods for measuring the rate of flow of air underground, so I prefaced my discussional charge to committee members with the statement that I regard air measnrements made in the usual way, with hand held anemometer, as no good. Agreements and disagreements came in from more than a dozen engineers, some of whom are with operating companies, coal and metal; some with manufacturers; others with government agencies. The statement was accompanied by a questionnaire on the use of the rotating vane anemometer and by one describing two methods of using a mechanically held anemometer. The questionnaire will be considered first. The questionnaire and statement are as shown on pages 5 and 6, the committee members and respondents are given on page 4, and the general comments of the latter on page 5. Questionnaire 1. Has your company or agency issued written instructions for care and use of anemometers? If so, please enclose a copy with reply. Only one answer, McElroy's, was affirmative. It gave reference to Bureau of Mines publications1'5 which recom- mend the hand held anemometer for rough measurements and indicate that am accuracy of 5 pct can be had if calibration and method factors are used. Mathews said that instructions are principally oral while Maize reported that state inspectors of his department are well trained in use and care of anemometers. 2. Are your anemometers calibrated periodically? If so, by their manufacturer? or by? Are calibralion corrections applied to all observed mean velocity readings? Only one respondent, Lee, answered negatively as to calibration. This means that anemometers are generally calibrated but the questionnaire failed to ask how often this is done. As no one volunteered the information, we have no data on this point. In six cases the instruments are sent to their manufacturers for calibration. but Krickovic reports that his company limits manu-facturers' calibrations to anemometers which are used by operating personnel; those used by the engineering department being calibrated by U. S. Bureau of Standards. The Anaconda Copper Mining Co. has its ventilation engineers calibrate its anemometers. Most of the respondents say that a calibration correction is applied to each mean velocity reading, but Krickovic limits this to surveys made by the engineering department. Since Lee does not calibrate, he has no correction to apply. Maize reports that his department has its anemometers calibrated but does not apply corrections. 3. Do your men hold the anemometer by hand in measuring air flow? for 1 min? or traverse the section? for 1 min? or at? points for 5 sec each? Of 10 replies, 6 were "yes," 3 were "no," and one was "seldom" with respect to holding by hand. Among the six hand holders, four hold in a central position in the measuring section for a minute, except that two of them, Krickovic and Matthews, traverse the section by hand for survey or fan test. Their operating personnel hold by hand, centrally, for routine measurements. McElroy sometimes traverses with hand-held anemometer in rapid survey work. 4. If the anemometer is not held by hand, how is it supported? Augustadt supports the anemometer on an adjustable rod, Condon on "a rod of sufficient length to reach all points with observer standing in one position throughout traverse and at arm's length from plane of traverse." I presume that arm's length must be interpreted liberally enough to allow for arm movement, otherwise it would be impossible to manipulate the anemometer throughout the traverse section. Mancha upholds Condon in this method of traversing. Glanville hangs the anemometer on the end of a 4-ft staff by the hasp at the top of the anemometer frame. McElroy mounts it on the end of a rigid square shaft, 12 in. long, the staff being at right angles to the axis of the instrument. He traverses the section in two halves, holding the anemometer 3 feet from his body.

Jan 1, 1950

By American Institute of Mining Engineers

David J. Mack (University of Wisconsin, Madison, Wise.)—Have the authors considered that the effects reported in their paper are readily explainable on the basis of equilibrium grain boundary segregation rather than ordering? It seems to the writer that all of their experiments and observations correlate well with known behavior associated with equilibrium grain boundary segregation. Although at first glance one would tend to dismiss such a possibility because of the similarity of the gold and copper atoms, their sizes differ by 12.8 pct which is in the range where segregation at grain boundaries would be expected. Then, too, the electrochemical differences between the copper, the Cu3Au, and the gold strongly suggest that a segregation mechanism is involved in the corrosion of the Cu-Au alloys. R. Bakish and W. D. Robertson (authors' reply)—The authors would like to thank Dr. Mack for his consideration of the problem of grain boundary segregation as an explanation of the observed phenomena. We had considered the problem in the following terms: Assuming a pure binary Cu-Au alloy and an ideal solid solution, the surface excess, T2= N25 — N2, of the second component (gold) may be expressed in the following way20 1 —exp (—da/kT) where 8 is the difference in surface tension of copper and gold, and a is the surface area per atom. In the present case, 6 is positive which implies that the component in excess at the boundary is gold. Since the only chemically active component in ferric chloride is copper, it does not appear that the segregation of gold is likely to increase the boundary activity. A small concentration of a third component could profoundly affect the situation. Analysis indicated only spectrographic traces of impurities, all of which are soluble in both copper and gold. Quenching experiments, reported in the paper, also tended to eliminate significant effects attributable to a third component.

Jan 1, 1958

By Daniel Su

Following several roof falls in the E3 longwall development of a Consol Pennsylvania Coal Company underground coal mine, an underground roof geology reconnaissance program consisting of twenty-nine 20-foot deep roof holes had identified the presence of thick sandstone layers with abundant shale and micaceous streaks. The base of the sandstone was 4 to 8 feet above the roof line within the fall areas. The presence of micaceous streaks created extremely pronounced planes of weakness in the sandstone. A structural irregularity, which extends into the E4 and E5 developments, exists between crosscuts I 1 and 30,where all roof falls occurred. Immediately to the east of this structural irregularity lies a huge syncline. The presence of thick sandstone units within the typically all shale environment and within such a structural irregularity helps to maximize stress concentration and creates closely spaced joints in the sandstone, which explains why many cracks are present in the macroscopically massive sandstone upon development. The approaching E2 longwall gob to the south and on the down-dip side, on the other hand, provided horizontal stress relief in the sandstone, which helps to explain the many roof falls in the E3 development that occurred during or immediately after the formation of the E2 gob. Finite element modeling confirmed the presence of such horizontal stress relief. Since the E3 longwall was a right-handed face, stress concentration was expected at the longwall headgate T -junctions, and further delamination of the sandstone was expected upon arrival of the E3 longwall face. Based on the results of the roof geology reconnaissance program and a roof stability analysis that took into account up to eleven parameters, supplemental headgate and track roof support consisting of 16-foot and 20-foot long cable bolts was successfully implemented within the zone of thick sandstone with micaceous streaks and structural irregularity and at other potential roof instability areas along the E3 development. The cable bolts were designed to be anchored at least 4 feet above the sandstone unit into the mostly competent sandy shale layers. No headgate roof control problem was reported within the sandstone and structural irregularity zone during E3 and the subsequent E4 longwall extractions.

Jan 1, 2002

By Ham. Y. M.

The corrosion behaviour of Al-B4C metal matrix composites immersed in 2500 ppm boron-containing H3B03, 0.5 M K2SO4, and 3.5% NaC1 solutions was investigated. Effects of B4C particle volume fraction on the corrosion behaviour of composites were studied using potentiodynamic polarization and electrochemical impedance spectroscopy techniques. Scanning electron microscopy was employed to study the surface morphology of the material before and after corrosion. Results show that all materials investigated are more corrosion resistant in 2500 ppm boron-containing H3B03 than in other solutions. No appreciable corrosion was observed in boric acid and sulfate solutions in contrast to an obvious pitting in NaC1 solution for both base alloy and composites. The preferential pitting sites are the interfaces of Al/Fe intermetallics for the base alloy, and the A1/B4C interfaces for the composites. Increasing the volume fraction of B4C particles in the composite decreases its corrosion resistance of Al-B4C composites.

Jan 1, 2011

By Arne Landsberg

A study of the chlorination kinetics of germanium, silicon, iron, tungsten, molybdenum, columbium, and tantalum has been made to determine the effects of temperature, chlorine concentration, geometric surface area and gamma radiation. The reaction products were volatile at the temperatures used this making it possible to follow the reaction rates by weight loss of the solid. Chlorination rates of germanium, silicon, and iron were found to be directly proportional to chlorine concentration while the rates for tungsten, molybdenum, columbium, and tantalum were proportional to the 0.5 to 0.6 power of chlorine concentration. A good correlation of reaction rate and geometric surface areas was not obtained because the true surface area of the samples could not be measured. Intense gamma radiation had no effect on reaction rates. The Arrhenius activation energies determined over the temperatures used are as follows: Germanium, 27 kcal/mole (233°-241° C); silicon 33 kcaL/mole (375°-517° C); iron, cold rolled, 20 kcal/mGle (259°-325° C) annealed, 21 kcal/mole (293°-337° C); tungsten, 43 kcal/mole (617-776° C); molybdenum, 37 kcal/mole (445°-4910 C); columbium) 34 kcal/mole (229°?255° C); and tantalum, 29 kcal/mole (370°-449° C).

Jan 1, 1965

The inherent weakness of the Zincor and similar iron removal processes is the relatively high undissolved zinc loss associated with the iron residue. High soluble zinc losses also occur due to poor filterability of the iron residue even though it may be limited to intermittent events. This work focussed on defining the optimum operating window for the Zincor iron removal process where iron is mainly removed in the form of amorphous, intermediate iron phases such as schwertmannite and ferrihydrite. In terms of the main operating conditions, optimum filterability was achieved under the following conditions: pH of 3.0, temperature as high as practically possible (70C), at least 25 kg/m3 seeding, and a retention time of at least 4 hours. When increasing the temperature from 60C to 70C, the required residence time decreased by almost 50%. Undissolved zinc loss was also reduced from 8% to between 2% and 3% by using a basic zinc sulphate/zinc oxide mixture as neutralising agent to effect iron removal.

Jan 1, 2003

By John Durkin

Electromagnetic narrow-band signals were transmitted through the earth at 27 coal mines located throughout the United States. From those Bureau of Mines tests, apparent earth conductivity values were derived based upon a homogeneous half-space model of the earth. The derived conductivity values were found to be inversely proportional to the transmitted frequency and mine depth. A linear regression model relating the logarithm of the conductivity to the mine depth was formulated, and the results indicate that the mine depth can be an adequate predictor of the apparent earth conductivity above coal mines. Apparent earth conductivity was found to decrease with mine depth.

Jan 1, 1984

By Roland C. Walker

Traditional headed rebar has existed in the mining industry as a ground support product for many years. The head of a rebar bolt is most commonly produced by hot upset die forging. Upset die forging produces a rugged, simple head that performs well. Certain elements of the head must comply with regulatory standards, such as ASTM F432-95, which offers a standard test procedure to ensure quality of the product. The head style produced by all major manufacturers has been optimized to reduce manufacturing costs, provide greater miner safety and provide an excellent performing product. Observations were made in some mines of heads failing under in-situ loading. These observations could not be replicated according to the ASTM testing method. This paper highlights the problem and how a solution was developed. The development includes pictures of in-situ failures from the underground operations, laboratory replication tests indicating how this loading occurs, and then the use of this calibrated test method to validate the new design created.

Jan 1, 2009

By John Durkin

Electromagnetic narrow-band signals were transmitted through the earth at 27 coal mines located throughout the United States. From those Bureau of Mines tests, apparent earth conductivity values were derived based upon a homogeneous half-space model of the earth. The derived conductivity values were found to be inversely proportional to the transmitted frequency and mine depth. A linear regression model relating the logarithm of the conductivity to the mine depth was formulated, and the results indicate that the mine depth can be an adequate predictor of the apparent earth conductivity above coal mines. Apparent earth conductivity was found to decrease with mine depth.

Jan 1, 1984

By A S. Fogliata, L Bengochea, G Mas, J E. Lazarte

The Culampajß auriferous district is located in the northern sector of the eastern edge of the homonymous hill, Catamarca Province, Argentina. Tajo Largo mine is situated in the southern flank of Las Minas gulch at an approximate height of 3.600 m above sea level. In the studied area main outcrops are orthogneiss rocks of Chango Real Formation. The ore mineral is native gold with a lesser amount of pyrite, chalcopyrite, haematite, limonite, malachite, azurite and covellite. These ore mineral assemblages are disseminated in quartz veins filling tension fractures in the host orthogneiss.Several types of inclusions have been recognised, including three phase H2O-CO2liq-CO2vap inclusions, polyphase inclusions with H2O-CO2 and one or more solid phases, and two phase aqueous inclusions. In the three phase H2O-CO2liq-CO2vap inclusions the Tmclath is about 1¦C and the CO2 liquid-vapour homogenisation occurs at 26 - 28¦C, to liquid phase. The homogenisation temperature of H2O-CO2 occurs at 365 - 380¦C in the aqueous phase. This set of data defined a solution with a salinity of 14, 4 wt per cent NaCl equivalent and a density of 0.84 g/cm3. In the two phase aqueous inclusions the melting temperature (Tm) of -5.4¦C and the eutectic point (Te) in -38¦C indicates a salinity of about 7.5 wt per cent NaCl equivalent, with the probable presence of Ca2+. Density of fluid is about 0.83 g/cm3. Homogenisation temperature ranges between 260¦ and 280¦C. The pressure, temperature and salinity of fluids in the polyphase inclusions suggest an early fluid of high density and high salinity. The three-phase fluid inclusions may be the result of an unmixing-phase separation of post magmatic hydrothermal fluid due to pressure decrease along fractures. It is suggested that the deposit was formed during the late magmatic hydrothermal stage genetically linked to granitic rocks and can be comparable with the intrusion-related gold system of Baker (2003).

Jan 1, 2008

By Ferid Kromer

This paper is the first in a series which will describe geology, mining methods, and production costs of some, of Turkey's more important minerals. In this paper the economically significant minerals-chromite, meerschaum, and magnesite-of the Tagtepe district are described. The cost data presented are believed by the author to be the first made public on Turkish chromite mining.

Jan 1, 1950

By G. W. Jones

Phthalic anhydride is a solid having the formula C8H4O3. It is an important intermediary in production of anthraquinene, alkyd reins, and plasticizers. The combined annual production of phthalic anhydride reported by 10 major manufacturers for 112,250 tons. The raw materials in the manufacture of phthalic anhydride have been the source of numerous fires and explosions. Consequently, the need was felt to determine the temperature flammability and the ignition temperatures crude basic raw material in most phthalic anhydride production crude phthalic anhydride, and pure phthalic anhydride.

Jan 1, 1950