Search Documents

By Missy Isaman

"Mixed ground tunnels come in all kinds. In rock tunnels with possible faults and high pressure water, the challenges are many. With the advent of Crossover TBMs, contractors can minimize machine wear in such conditions while maximizing efficiency. The newest generation of Crossover is exemplified by two projects in Albania and Turkey. A 5.56 m Crossover TBM destined for Turkey’s Gerede Water Transmission will be assembled using Onsite First Time Assembly (OFTA) from within an existing tunnel. The unique machine will bore through 30 fault zones requiring the TBM to be sealable to up to 20 bar so pre-consolidation grouting can be done. If boring under pressure is required, the TBM will bore sequentially using the screw conveyor fore and aft gates. Skewing further towards hard rock, a unique 6.2 m diameter Double Shield TBM with Crossover features was designed for Albania’s Moglicë Headrace Tunnel. The machine features closure doors and a sealing system to contain inrushes of water until they can be grouted off. This paper will discuss the unique aspects of the Crossover designs, including their inception as based on past projects in difficult ground, and their utilization at the two current projects. INTRODUCTION Specialized tunnel boring machines have been made for years to tackle specific types of ground conditions. Traditional types of TBMs bore within a specific set of ground conditions. If a project is located in a competent granite face, then a Main Beam machine is a good solution. In soft ground, Earth Pressure Balance (EPB) machines are the method of choice. Years of experience and engineering advancements have made both types of machines fast and economical solutions for tunneling. Unfortunately not all ground conditions are a perfect swath of one material, and the need for a more diverse machine is apparent."

Jan 1, 2016

By H. A. Watson

Laboratory tests on three commercial methane detectors, two combustion- type detectors and one interferometer-type detector, were made by the Bureau of Mines to determine their response to certain single and multiple flammable gases mixed with normal and abnormal air atmospheres. Although both types of detectors responded accurately to methane-normal air mixtures, they did not show correct concentrations for other single flammable gases in air. Uniquely, the response of the interferometer-type detector to hydrogen was in a negative direction. The effects of individual gases in multiple flammable gas mixtures were approximately additive. In oxygen-deficient atmospheres the methane response of the interferometer-type detector erred on the high side, but only in very low oxygen concentrations were the combustion-type detectors affected-- showing low, erratic methane readings.

Jan 1, 1966

By Néstor Deza, Kim Montes

En los últimos 20 años la operación minera en Antamina ha profundizado su tajo, el stripping ratio y la distancia de acarreo de desmonte, se han seguido incrementando para mantener la producción metálica. Tal como ocurre en las todas operaciones mineras de tajo abierto, se espera en los próximos años un incremento sustancial de la cantidad de desmonte a remover conforme se avance las siguientes extensiones de vida. En adición a esta situación, los recientes compromisos globales de reducción de emisiones de carbono exigen reducir progresivamente hasta eliminar el 100% la emisión de carbono, opuesto a lo requerido para seguir operando con métodos convencionales. Estos dos factores afectan la sustentabilidad en el largo plazo en todas las empresas mineras maduras como en el futuro de Antamina.

Sep 30, 2022

By N. A. Gokcen

Equilibrium partial pressures of gaseous HCl and H2O over aqueous binary and ternary solutions of HCl and AICls were calculated or estimated in the range of 20° to 110° C, and up to saturation with AlC13?6H2O. The results were extended to solutions containing less than 10 wt-pct FeCl3 by assuming that FeCl3 and AIC13 are equivalent on the molar basis, since both salts have trivalent cations with a cammon anion. The ionic activity coefficient of HCl and the equilibrium constant for dissolution of gaseous HCl were also computed. This research is part of the effort by the Bureau of Mines, U.S. Department of the Interior, to provide thermodynamic data to expand the technology base relevant to the extraction of alumina from nonbauxitic domestic raw materials.

Jan 1, 1980

By Alei Leite Alcantara Domingues

A microscopia óptica é uma ferramenta importante para o entendimento dos processos envolvidos na produção do minério de ferro e seus aglomerados. Nos laboratórios em que esse tipo de análise é feita, tem-se geralmente um microscópio de luz refletida e um operador treinado que leva diversas horas para concluir uma única amostra. Nesse trabalho serão mostrados exemplos de resultados de minérios de ferro, sínter e pelotas obtidos em um sistema de microscopia óptica automática com análise de imagens. No estudo do minério de ferro foram determinados a composição mineralógica quantitativa, morfologia das partículas e tamanho dos cristais. Na microscopia de sínter foram determinados a quantificação de fases, porosidade, textura, recristalização de hematita e morfologia das ferritas. Nas pelotas produzidas com minério de ferro foram feitas análises de quantificação de fases, distribuição e quantificação dos poros e evolução microestrutural dos grãos. A implantação de um sistema de microscopia óptica automática com análise de imagens permite que análises sejam feitas em menor tempo, com maior reprodutibilidade possibilitando que a técnica seja implantada em áreas de produção que exijam respostas mais rápidas.

Oct 30, 2017

ABERDEEN, ESTHER, U. S. Geological Survey, Washington, D. C. ALLEN, VICTOR T., Director Geology Department, Institute of Technology, St. Louis University, St. Louis, Missouri. BATES, THOMAS F., Associate Professor of Mineralogy, Department of Earth Sciences, School of Mineral Industries, The Pennsylvania State College, State College, Pennsylvania. BOLGER, ROBERT C., Geologist, Pennsylvania Topographic and Geologic Survey, Harrisburg, Pennsylvania. BRIDGE, JOSIAH, U. S. Geological Survey, Washington, D. C. BURST, JOHN F., Geologist, Exploration and Production Research Division, Shell Oil Company, Houston, Texas. CAMPBELL, IAN, Executive Officer, Division of Geological Sciences, California Institute of Technology, Pasadena, California. FLINT, DELOS E., U. S. Geological Survey, Washington, D. C. FREDERICKSON, A. F., Associate Professor of Geology (Geochemistry), Washington University, St. Louis, Missouri. GLASS, HERBERT, Illinois State Geological Survey, Urbana, Illinois. GORDON, MACKENZIE JR., Geologist, U. S. Geological Survey, Washington, D. C. GRIM, RALPH E., Research Professor, Department of Geology, University of Illinois, Urbana, Illinois. HARDER, E. C., Aluminium Secretariat Limited, Montreal, Que., Canada.

Jan 1, 1952

By Gleyson Marcos Barbosa

A forma cilíndrica de bobinas a quente semi-acabadas é essencial para permitir normalidade nas operações posteriores de transporte e utilização. Entretanto tal forma, que é conferida pela bobinadeira, pode ser perdida devido um fenômeno chamado “ovalização”. Com este problema as bobinas assumem uma forma oval, o que pode gerar diversos transtornos, tais como comprometer a inserção da bobina nos mandril do processo seguinte, prejudicar o processo de desbobinamento e colocar em risco a segurança das operações de estocagem nos pátios e transporte. Esta contribuição técnica tem como objetivo mostrar as recentes atividades realizadas por uma equipe multifuncional de 3 diferentes unidades do grupo ArcelorMittal em busca de alternativas para controle da ovalização sem gerar efeitos colaterais indesejados no ciclo produtivo.

Jul 30, 2018

By Marcus Novaes Motta

O modelo utilizado como base para elaboração deste trabalho, foi desenvolvido com os dados coletados no start up da planta de desfosforação de gusa líquido, fornecida pela TECNOSULFUR S/A, localizada em Sete Lagoas - MG a Siderúrgica CISAM, localizada em Pará de Minas – MG. Esse modelo prevê de forma precisa a quantidade de agente desfosforante necessário para o tratamento de desfosforação de ferro gusa, considerando o teor de fósforo final objetivado e levando em consideração o fósforo, silício e temperatura iniciais. O objetivo deste trabalho é testar esse modelo em outros reatores que possuem processos de desfosforação, tais como: desfosforação de aço em convertedores e fornos elétricos. Inicialmente foram coletados dados de desfosforação de algumas publicações para verificação de viabilidade desse trabalho e como o modelo se mostrou eficiente, futuramente ele será testado em algumas empresas e se necessário será ajustado.

Aug 16, 2017

By Duane E. Eubanks, David B. McDonald

The anticipated growth of western coal production over the next decade is expected to add approximately 274.3 million t/y (302.4 million stpy) to US capacity. The increased output, coming from both new mines and expansion of existing facilities, promises to bring with it a new set of problems for mine planners.

Jan 8, 1976

By Howard J. Pincus

The purpose of the study is to investigate the effects of fracture fillings and associated alteration on the mechanical behavior of rocks. Experimental results are presented for 98 specimens from the Climax mine, which were tested since the annual report (May 1973). The conclusions reached are based on both these results and those reported in the annual report. The locations studied are the Climax and Henderson mines in Colorado and the San Manuel mine in Arizona. The rock types studied from each location are from: 1) Climax, medium-grained granite, fine-grained granite, granite porphyry, schist, and gneiss; 2) Henderson, rhyolite porphyry; 3) San Manuel, quartz monzonite and quartz monzonite porphyry. A description of the rocks was made including: color, texture, mineralogy, composition and fabric of fracture fillings, density, apparent porosity, and optical diffraction patterns. Unconfined and triaxial compression tests were run on the Climax and San Manuel specimens. Sonic velocities were measured during the compression tests; Shore sceleroscope hardness was measured before the compression tests. Conclusions are that some relation appears to exist between compressive strength and the following properties and features for all specimens: dynamic Young's modulus, sonic velocity, density, rock composition, slope of velocity curve, composition and fabric of fracture fillings-veinlets, and apparent porosity. There appears to be some relation between compressive strength and Shore scelerscope hardness for the quartz monzonite (San Manuel). A relation appears to exist between texture and compressive strength and the extent of failure on fracture fillings for schists, gneiss, and fine-grained granite (Climax). The amount of swelling clays (montmorillonite, hydromicas, etc.) present in the rock and the relative number of fractures in which they constitute of major portion of the fracture fillings are related to the strength of the rocks. Possible tests for checking the amount of these clays present is presented including saturation, dyes, and X-rays. A useful index relating to rock strength, as revealed in this study, is the presence of swelling clays in detectable abundances. These clays can be detected in the field with a simple wetting and striking test; in the laboratory they can be detected by X-ray and dye methods.

Jan 1, 1974

By Osvaldo Benedito Dib Melo

O trabalho tem por objetivo de mostrar uma otimização da performance de sistema de lavagem de gases (conjunto espessador e filtro a vácuo) do Alto Forno de uma siderúrgica localizada no Nordeste, a CSP, Cia Siderúrgica do Pecem. A unidade entrou em operação no ano de 2016, inicialmente com orientações/informações de projeto, tendo muito desvios no controle da turbidez e sólidos suspensos da água da saída do espessador, em função da tecnologia aplicada, que não estava funcionando adequadamente para a realidade da região e ocasionava custo elevado, além de muitos problemas operacionais. A metodologia aplicada baseou-se em teste na planta com produtos químicos, ensaio de laboratório com teste de jarro e análises físico-químicas da água de recirculação. Os resultados obtidos foram excelentes na redução da turbidez e sólidos suspensos, aumento da retirada de lama pelo filtro rotativo, maior tempo de uso da manta dos filtros a vácuo e uma redução de custo com produto químicos e mão de obra, totalizando uma economia significativa em reais/ano.

Oct 30, 2017

By Ana E. Bohé, Georgina De Micco, Gastón G. Fouga

"In this work the reaction between several manganese oxides and chlorine is investigated in the range of temperatures between 650 and 950ºC. The reaction path for the chlorination of MnO is established, which involves recrystallization of high valence manganese oxides (Mn3O4 and Mn2O3) followed by its chlorination. For this reason, to understand the reaction of MnO, the chlorination of Mn3O4 and Mn2O3 has also been studied. The starting temperature for the reaction of these oxides is determined by non isothermal thermogravimetric measurements. The effect of temperature is analyzed, under our experimental conditions the rate of reaction is mass transfer controlled. The activation energy for the volatilization of manganese chloride is obtained which is in good agreement with volatilization enthalpy of MnCl2.IntroductionMany oxide ores which have manganese in their composition undergo chlorination processes during the extraction of refractory metals such as Ti, Hf and Nb. Although several works related with chlorination of manganese oxides were reported, there is no information about the kinetics or mechanism of the manganese oxide chlorination reactions. Okahara et al. studied the chlorination of manganese oxides and established that they react easily above 250ºC. Furthermore, they observed that chlorination of high order oxides is more difficult when there is not a reducing agent [1]. Ivashentsev studied the chlorination of manganese oxides using Cl2(g), CO(g) + Cl2(g) and COCl2(g). He established that the reaction of MnO started at 130ºC with formation of MnCl2(s), he also observed recrystallization of manganese sexquioxide [2]. Finally, the chlorination of manganese nodules from the ocean was studied by Murthy and Reddy [3] with the aim of obtaining valuable metals such as Mn, Co, Ni and Cu. They studied the influence of several parameters like temperature, carbon percentage, particle size and chlorine flow rate in the extraction process."

Jan 1, 2008

By Antônio Carlos Aguiar Gagno Junior

O Sistema de Controle de Equipamentos de Radiofrequência (SCER) nasceu a partir de uma demanda da área de Telecomunicações com o objetivo de minimizar as interferências dos diversos equipamentos emissores e receptores de ondas de rádio existentes em todo o perímetro da Usina ArcelorMittal Tubarão. Anterior ao sistema, todo o cadastro, controle e alocação destes equipamentos era feito em planilha Excel, mantida pela área de telecomunicações. Todas as verificações para liberação da instalação/configuração do equipamento a ser instalado eram feitas manualmente, com auxílio de equipamento analisador de espectro de frequência. Com a implantação do SCER, as fragilidades do controle manual foram supridas, trazendo o diferencial de cálculos automáticos de interferências feitos pelo sistema em função dos parâmetros de ajuste de cada equipamento, da sua abrangência e localização geográfica. Através de uma interface Web, os usuários podem não só controlar os equipamentos, fabricantes, modelos e aplicações, como também visualizar em mapas, com georreferenciamento, as áreas da Usina em que estes equipamentos atuam, bem como alterar os polígonos e perímetros de alcance e abrangência das áreas.

Aug 16, 2017

Notices STRASZACKERREPORT The Institute has received, for its information, a copy of the following letter, which was addressed to The Federation of Societies of Professional Engineers: REPORT: COMMISSION OF ENQUIRY INTO THE METHODS OF TRAINING FOR UNIVERSITY DEGREES IN ENGINEERING (STRASZACKER REPORT) Geagte Heer, VERSLAG: KOMMISSIE VAN ONDERSOEK NA DIE METODE VAN OPLEIDING VIR UNIVERSITEITSGRADE IN INGENIEURSWESE (STRASZACKERVERSLAG) Second International Symposium on Jet Cutting Technology This symposium, sponsored and organised by BHRA Fluid Engineering, of Cranfield, England, is to be held at St John's College, Cambridge, from 2nd to 4th April, 1974. Competition for student members of the South African Institute of Mining and Metallurgy Each year the Institute offers a prize (or prizes should the entries warrant it) of up to R100 for the best paper or dissertation on a topic appropriate to the interests of the Institute. Techomin 74 - World Mining Fair The above World Mining Fair, under the sponsorship of the International Committee for the Organization of World Mining Congresses and the Peruvian Government, is to be held in Lima, Peru, from 3rd to 12th November, 1974, to coincide with the 1974 World Mining Congress, which is to be held in Lima. NIM Reports Report No. 1435 The determination of chromium, manganese, iron, cobalt, and nickel by atomicabsorption spectrophotometry using the nitrous oxide-acetylene flame. Report No. 1463 Liq'uidus temperatures and activities of manganese (11) oxide in slags associated with the production of high-carbon ferromanganese alloys. Report No. 1467 The spectral analysis of solutions. 1. The analysis of rare-earth minerals. Report No. 1479 Infrared studies of the adsorption of oleate species on mineral surfaces,with special reference to fluorite. Report No. 1483 The South African manpower requirements in extractive metallurgy. Report No. 1484 Cost estimates for the production of copper wirebars from sulphidic ores. Report No. 1486 Review of the jluoro-chemical industry of the World. Report No. 1490 The adsorption of krypton, nitrogen, and water vapour on sodium oleate. Report No. 1491 Technology and economics of the Olaus kiln under South African conditions. De Beers Report The dry grinding of tungsten carbide/ steel combinations with diamond wheels. Metallurgical Directory The Israel Export Institute has just published the first edition of the Israel Metal Industry Directory, which gives pertinent information relating to the 750 Israeli manufacturers of metal products-addresses, annual turnover, and products- and to consulting engineers and export companies specializing in metal products. Visiting Nuclear Scientist The National Institute for Metallurgy has announced that Professor Vincent P. Guinn, of the University of California, is to spend his sabbatical leave (April to June) working with the Activation Analysis Research Group of the National Institute for Metallurgy.

By Caroliny Gomes de Oliveira

O presente trabalho avaliou a utilização de uma célula eletroquímica portátil de ensaio de EPR-DL aplicada na detecção da susceptibilidade à corrosão no aço inoxidável superduplex UNS S32750. Amostras do referido aço foram tratadas termicamente na temperatura de 850°C por tempos de 1, 10, 60 e 600 minutos para criar diferentes padrões de precipitações de fases deletérias. Foram utilizadas as técnicas de microscopia ótica (MO), microscopia eletrônica de varredura (MEV) e espectroscopia por dispersão de energia de raios-x (EDS) para análise da microestrutura. Os resultados mostraram que a célula portátil de EPR-DL foi capaz de detectar com sucesso a presença das fases deletérias precipitados no aço. Além disso, quanto mais longo o tempo de tratamento, maior foi o grau de precipitação e, consequentemente, maior a susceptibilidade à corrosão no AISD, em função da maior razão Ir/Ia obtida.

Aug 7, 2018

By Arnold B. Hubbard

Automatic control instruments were utilized by the Bureau of Mines for routine assays of large numbers of oil shale samples and other bituminous materials. The standard Fischer assay method was automated by automatically controlling the heating cycles of a battery of 12 electric heaters with electronic controllers and programmers. The condensers were cooled with a modified automatically controlled refrigeration bath. The complete assembly consisted of 12 retort units, necessary control instruments, and the refrigeration bath. This equipment was capable of producing more consistent results than those previously obtained with the gas-heated retorts and of increasing the output of assays substantially with no increase in operating personnel.

Jan 1, 1965

By G. Carman Ridland

A program of exploration for radioactive deposits, conducted in 1945 in the well-known mineralized areas of the Front Range, Colorado, was rewarded with the discovery of pitchblende in a dump at Caribou Hill. The presence of pitchblende in. the silver veins at depth apparently is not expressed as gamma-ray anomalies at the surface.

Jan 1, 1950

By Edward M. Dowey

This paper presents the excavation of the Roosevelt Island Valve Chamber, the final of three chambers in Stage One of New York City's Third Water Tunnel. The valve chamber and passageways 13 379.7 cu m (17 500 cu yd) are drilled and blasted. The rock is stabilized by grouted rock anchors. The 6.1 m (20 ft) diameter shaft is drilled, blasted, rock bolted and wire meshed for a depth of 70.7 m (232 ft). Then shaft excavation proceeds with immediate concrete lining for another 120.7 m (396 ft). Two 6.1m (20 ft) diameter manifolds are excavated using heading and bench. The raise drilling of eight 3.7 m (12 ft) diameter laterals occurs during lower shaft sinking.

Jan 1, 1987

By T. Cienski

The paper presents and discusses the results of a detailed study conducted on the subject of energy consumption in the comminution of industrial minerals. The study was based on pilot circuit testing, plant operating data collection, detailed equipment data and literature research. The areas covered by investigations include: high efficiency classification; air classifiers for cement grinding circuits; grinding aids in dry grinding: dry grinding circuit, control based on particle size measurement. Results obtained indicate a large potential for the reduction of energy consumption, in particular in the traditionally high cement clinker grinding circuits. Better classification techniques and correct application of grinding additives can significantly reduce power used per ton of product and also substantially increase grinding circuit output.

Jan 1, 1990

By Maureen M. Foss

Underground coal mining is hazardous due to changing geological conditions. One geophysical method showing promise for in-seam hazard detection is ground-penetrating radar (GPR). The Bureau of Mines recently completed preliminary studies to demonstrate the feasibility of using GPR for in-seam hazard detection. Investigations included air and coal tests for the purpose of checking equipment accuracy, coal penetration, and other factors such as the effects of receiver orientation. Further investigations involved using both a short pulse and a new prototype synthetic-pulse system to locate a clay vein in a coal seam using trans-illumination. Data were gathered on multiple travel paths, and a back projection processing technique was then used to create a tomographic image using the calculated velocities. A computer model of the same coal seam was subsequently processed using the same tomographic tech-nique, and the results were compared with those of the actual data. Analysis of the tomographic images shows the presence of the clay vein, although its boundaries are unclear due to the tomography method used. Results of these preliminary studies show that GPR is feasible for use in in-seam hazard detection and point the direction that future research should take. A need has been shown for research involving more sophisticated tomography techniques, transmission studies on thicker coal seams, and reflection studies using the synthetic-pulse system.

Jan 1, 1987