Search Documents

By Aprígio Ângelo de Jesus

No presente trabalho, foram avaliados os efeitos do tratamento térmico de alívio de tensões na microestrutura e propriedades mecânicas de juntas soldadas dos aços SA516-70 e SA387-11 (ambos aplicados na fabricação de vasos de pressão). Chapas com 40 mm de espessura de ambos os aços foram soldadas por arco elétrico com arame tubular e, posteriormente, submetidas a tratamento térmico para alívio de tensões. A variação de dureza ao longo da solda e a resistência à tração dos materiais soldados e tratados termicamente foi avaliada. A microestrutura dos materiais soldados foi acompanhada por microscopia ótica convencional. Por meio do tratamento térmico empregado foi possível observar a redução do nível de encruamento nos metais base e zonas termicamente afetadas das juntas em ambos os materiais com aumento de ductilidade no aço SA516-70.

Aug 8, 2018

By Andrew M. Leszcykowski

In 1984, personnel from the U.S. Bureau of Mines examined the 9,550-acre Yatahoney Creek Wilderness Study Area (WSA) for mineral resources. This study area, in southwestern Idaho, is underlain by tuffs and basalt of Tertiary age. Owyhee County mining records and U.S. Bureau of Land Management records, and other references were examined prior to the field study. There are no known mines, claims, or prospects in or near the WSA. No evidence of mineral deposits or occurrences was observed. Oil and gas leases or lease applications are in the southern portion and northeast corner of the WSA. Although placer gold exists in the Owyhee River drainage, there are insufficient deposits of gold-bearing gravel in the Yatahoney Creek WSA to enable mining. INTRODUCTION The U.S. Bureau of Mines (USBM) and the U.S. Geological Survey (USGS) conduct mineral surveys of designated wilderness study areas (WSAs) 1/ to ensure mineral values that may be present are considered in wilderness recommendations. The USBM examines known mines, prospects, and mineralized sites, and the USGS performs geologic mapping, and geochemical and geophysical surveys on an areal basis.

Jan 1, 1986

By Ana Carolina Ribeiro Duarte

A combinação de propriedades apresentada pelos aços perlíticos permite sua aplicação em diversos segmentos. O objetivo deste trabalho foi caracterizar a microestrutura do aço SAE 1070 deformado via trefilação para a fabricação de fiomáquina. O aço foi trefilado a seco por 12 passes com reduções médias entre 15 e 21%. A caracterização microestrutural foi realizada com o auxílio da técnica de microscopia eletrônica de varredura e microscopia de força atômica. O material teve ainda seu comportamento mecânico avaliado por meio de ensaio de dureza Vickers e ensaio de tração. O material deformado apresentou a estrutura “curling” na seção transversal, enquanto que na seção longitudinal a maioria das lamelas se encontrava alinhadas com a direção de trefilação. Os ensaios de tração e dureza revelaram um aumento considerável da dureza e resistência do material após o processo de trefilação.

Aug 16, 2017

By Kelly Cristina Ferreira

A determinação do consumo energético e o dimensionamento da etapa de moagem tem sido objeto de estudo de diversos pesquisadores desde o século XIX, iniciandose com Rittinger e Kick. Mais recentemente, outras técnicas, envolvendo modelagem matemática do processo têm sido aplicadas com sucesso. O material em estudo é um minério de ferro itabirítico da região de Morro do Pilar. Foram estudadas as etapas de moagem primária e remoagem. Diferentes metodologias foram utilizadas para determinação do consumo específico de energia na moagem primária, além da determinação dos parâmetros de quebra e seleção para diferentes colares de corpos moedores e otimização do circuito pré-dimensionado. Os resultados indicaram um consumo específico de energia pequeno para o minério em questão. Além disso, o teste de WI de Bond, com escalpe inicial na malha de controle, apresentou valores mais próximos do valor simulado.

Aug 17, 2017

By Morris J. Viljoen, Young. David R.

"Abstract -The zone of economic interest at H.J . Joel Gold Mine is the VS5/Beatrix Composite Reef, a quartz-pebble conglomerate of Archean age. The reef occurs at the base of the Eldorado Formation, Central Rand Group, of the Witwatersrand Supergroup. At !east three stratigraphically distinct conglomerates form this economic zone. In order of deposition these are the Footwall, Beatrix, and the VS5/Beatrix reefs. The Footwall and Beatrix reefs are equated with the Aandenk Formation with transport directions toward the northwest, whereas the VS5/Beatrix Reef is of Eldorado age, with transport directions toward the south. The change in the drainage direction was caused by a major basin-wide tectonic event that occurred prior to the deposition of the Eldorado Formation. The Beatrix Reef was formed in a proximal, braided, fluvial environment by a process of aggrading gravel bars between channelways. The VS5/Beatrix Reef was formed by the desegregation of pre-existing Beatrix Reef with the introduction of new material containing much shale detritus and is seen to have been deposited in a more ·distal, braided, fluvial environment, similar to the Beatrix Reef.The average gold concentrations are different for each conglomerate; the Beatrix at 32.1 ppm Au, the Footwall at 24.4 ppm Au, and the VS5/Beatrix at only 12.4 ppm Au. A sedimentary gold concentrating process related to higher energy braid channels was primarily responsible for these high gold grades. Not only the basal unconformity surface, but also, internal degredation surfaces, were prime sites for concentration. An understanding of the spatial distribution of these differing conglomerates and their braid channels forming the economic reef zone is necessary in predicting ore grades for future mining."

Jan 1, 1994

By Renato Drescher Subtil

A tecnologia de cominuição de minérios através de Prensas de Rolos de Alta Pressão vem se destacando nos diversos segmentos da mineração, o que faz com que as usinas de pelotização de minério venham introduzindo Prensas de Rolos em seu processo produtivo. Apesar dos benefícios dessa mudança, observa-se pouco conhecimento da influência das variáveis intervenientes ao processo de prensagem e sua relação com o Ganho de Superfície Específica. Essa compreensão é fundamental para a maximização do desempenho de prensagem. Esse artigo utiliza Redes Neurais Artificiais (RNA) para predição dos resultados no Ganho de Superfície Específica e quantifica a relevância de cada variável no processo de prensagem. Os valores preditos gerados pela RNA obtiveram ótima aproximação com os dados reais, o que indica que utilização de RNA possibilita a intervenção proativa no processo produtivo podendo resultar em uma melhoria de desempenho da prensa.

Aug 17, 2017

By Ivan Kwei Liu Kam

O presente trabalho propõe a carbonetação a laser de ferro puro para a formação de uma camada endurecida na superfície. A formação de uma camada dura permite obter peças com melhores propriedades tribológicas, mas sem alterar as propriedades volumétricas do sólido. Foram realizados experimentos em quatro condições de tratamento a laser, com uso de uma fonte do tipo fibra de Yb:vidro. Análises microestruturais e de dureza mostraram a formação de camada ledeburítica e martensítica, dependendo das condições experimentais, até cerca de 50 µm de profundidade. Análises por calorimetria permitiram, também, verificar que a absortividade do laser na peça variou entre 30 e 46%. Estes resultados mostram que o uso de laser para a carbonetação de peças ferrosas, com a metodologia proposta, permite um alto rendimento, alta dureza da superfície e baixo aporte térmico ao material.

Aug 7, 2018

By Richards BG, Komdeur W

Instability in spoil piles and in high wall slopes in natural overburden has been ex- perienced at Utah's Goonyella Mine since com- mencement of operations in early 1971. Annual production targets, although gener- ally met since the commencement of operations, required modifications to stripping and mining techniques and the rapid re-scheduling of oper- ations around unstable areas, but culminated in the earlier than planned acquisition of addit- ional stripping equipment. An understanding of failure mechanisms was developed within a collaborative study of pitwall instability between Utah Development Company and the C.S.I.R.O. Division of Applied Geomechanics. Results showed that pitwall instability occurs as structurally controlled deformations along planar failure surfaces; spoil pile failures are precipitated by moist- ure ingress and subsequent loss of strength of base layer materials; highwall failures de- velop over areally extensive bedding planes in conjunction with inclined and subvertical fractures caused by overburden blast damage.

Jan 1, 1978

By E. G. King

The Bureau of Mines made experimental determinations of the heats of formation of forsterite and chrysotile at 298.15° K. The heat capacities of two polymorphs of serpentine, chrysotile and antigorite, were measured over the temperature range from 50° to 298° K and the entropies at 298.15° K were evaluated. The heat content of antigorite above 298.15° K was measured to 850° K. These thermochemical data were combined with other pertinent data to give heat and free energy of formation values at high temperatures. Free energy values are given for the reaction, forsterite + water = brucite + serpentine at different temperatures and pressures.

Jan 1, 1967

By M Darby, B Burdett, F Lovell

The results of the process control improvement project aimed at improving the quality of Australian Bulk MineralsÆ (ABM) iron ore pellets produced by four vertical shaft furnaces are very positive. These results are achieved through process stabilisation and optimisation, improvement in process monitoring and taking early corrective actions when operating variables were outside the target ranges. A number of benefits are obtained from this project. These benefits include: More consistent and improved pellet quality. The average cold compression strength (CCS) value of pellets produced during the eight-month trial is 260 kg/pellet, which is 16 kg/pellet higher than that produced during the 12 months prior to the trial (244 kg/pellet). Reduction in the heat input by eight per cent, from 727 MJ/tonne to 668 MJ/tonne. Reduction in bentonite rate by six per cent, from 7.1 kg/tonne to 6.7 kg/tonne. Increase in the furnace throughput rate by four per cent and additional production of 10 000 tonnes per annum through process stabilisation. Better understanding of the process behaviour. This knowledge is valuable not only for setting the target operating conditions but also for developing the ABM expert system to control the process.

Jan 1, 2005

By Rosiane Mary Rezende Faleiro

O carvão vegetal, CV, é o componente individual com maior impacto no custo final de uma usina integrada. Diante desta realidade, foi desenvolvido um processo de carbonização contínua, uma tecnologia moderna que a diferencia das carbonizações tradicionais, permitindo que o CV produzido tenha melhores características físicoquímicas. Sendo assim, o desafio agora é encontrar condições operacionais adequadas para produzir em larga escala a um custo competitivo. Com base nisso, desenvolveu-se este trabalho com o objetivo de avaliar o desempenho de um altoforno, em condições reais de operação e em escala industrial, utilizando dois tipos de carvões (CVs): CV Referência e CV produzido por carbonização contínua (Carboval). Os principais parâmetros operacionais foram monitorados. O CV Carboval apresentou melhores resultados para as análises químicas e granulométrica, melhor permeabilidade no alto-forno e menor consumo bruto, demonstrando sua viabilidade técnica.

Aug 17, 2017

By Weijie Wei, Jinwang Zhang, Shengli Yang

Due to the unbalanced top coal drawing process, the recovery ratio is low, and the equipment stability is poor in the longwall top coal caving mining (LTCC) with an inclined seam. Aimed at these problems, this paper proposes the dynamic group caving method (DGCM). The basic procedure is that when the drawn volume of top coal from a support reaches about half, the next support begins drawing top coal, and the drawing process between the two supports is half done. Taking the panel no. 8103 in Beixinyao mine as the research object, the characteristics of drawing body shape, particle movement trace, and variation of recovery ratio are investigated by using Particle Flow Code. Furthermore, the effect of mining-caving ratio on the top coal drawing law under DGCM is revealed by the simulation results, and compared with the single-opening sequence caving method (SSCM) and the doubleopenings sequence caving method, advantages of DGCM are determined in inclined seams. The results show that the drawing body can be divided into the left and the right under DGCM. Specifically, the drawn top coal particles in the left are from the upper part of this support, that in the right are from the lower part of next support, which verifies the correctness of the theoretical analysis. The characteristics of the drawing body shape are more significant when the mining-caving ratio is relatively small. In addition, with increasing mining-caving ratio, the recovery ratio of the panel both increases gradually underDGCMand SSCM.When the miningcaving ratio is less than 1:1, the recovery ratio of DGCM is obviously higher than that of SSCM, indicating that DGCM can greatly improve the recovery ratio. While when the mining-caving ratio is larger than 1:1, the recovery ratio of two caving methods is basically equal; however, the advancing time is significantly shortened under DGCM. This study are of great significance to realize high efficiency and precise caving in LTCC with an inclined seam.

Jul 7, 2020

By M. L. Glenn

The Bureau of Mines is conducting research on substitutes for chromium-containing alloys in order to conserve imported critical and strategic materials. Part of this research concentrates on finding low-chromium substitutes for heat-resisting stainless steels for the temperature range 600° to 800° C. Ferritic alloys are emphasized that have oxidation resistance provided by chromium contents as low as 10 pct and stress rupture strength provided by the precipitation of the chi(X)-phase intermetallic compound, (Fe36Cr12 (Mo, Ti)10). Initially, research was concentrated on selecting an alloy composition having a minimum chromium content with strengthening provided by the X-phase. An Fe-(10-12 pct)Cr-6 pct Mo-(1.5-2.0 pct)Ti alloy was selected. After the alloy selection, the tensile, stress rupture, and oxidation properties were determined. Stress rupture properties were found to be similar to those of 304 stainless steel. However, the alloys possessed brittleness during both stress rupture and tensile testing, possibly as a result of too high a content of molybdenum and titanium. Higher than expected oxidation rates were found that may be caused by the high molybdenum content.

Jan 1, 1984

By Florian Kongoli

The production of a homogeneous self-fluxing sinter is an important step in iron making processes. A good sinter should have good permeability and reducibility and has to keep those characteristics for a certain time. An early melt down of the sinter in the blast furnace, where its solid state reduction is essential, would cause many problems such as low permeability and reductibility. Nevertheless, the important factors that influence these characteristics, such as the chemistry of the sinter and the fluxing effect during sintering and sinter reduction conditions have not yet been clarified. In today's new reality where many new minor components such as Al2O3 and MgO enter to the sinter through raw materials, the quantification of the fluxing effects during sintering becomes even more important. In this work, the liquidus surface and phase relations of the sinter primary melts in the CaO-FeO-Fe203-Si02 system at sintering conditions have been quantified. The fluxing effect of oxygen potential, Al2O3 and MgO has also been quantified by the means of some practical diagrams that can directly help the optimization of the sintering processes.

Jan 1, 2003

By N Weerasekara, M Bird, M Yahyaei, M M. Hilden, M S. Powell, J Franke, P Toor

The combination of new tools with a more rigorous approach to understanding the interaction of mill liners with overall mill performance and economics, forms the basis of an integrated approach to liner management. Based on accurate liner wear measurements, some (limited) physical mill inspections and surveys, accurate calibration of the mill load and analysis of process data, a whole new approach to liner selection, relining intervals and mill control is proposed. Collection and analysis of this information in operating mills illustrates the mill performance improvement which can be attained through this careful measurement and modelling approach.A more holistic approach to liner management is proposed, including a broadening of the current work to cover the potential benefits of improved relining technologies and predictive liner wear modelling. CITATION:Powell, M S, Hilden, M M, Weerasekara, N, Yahyaei, M, Toor, P, Franke, J and Bird, M, 2012. A more holistic view of mill liner management, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 95-104 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

During the last 12 years the dominant theme at Mount Isa has been production expansion. Production rate of 3,200 tons per mine day in 1953 increased to 11,000 tons per mine day in 1960, completing the first stage of the programme. The second stage is still in progress. It is planned to increase production of lead and copper ores to 19,500 tons per mine day in 1968.Current mine workings comprise an area 2 miles long and 1/2 mile wide, the deepest production level being 2,000 ft below surface. During the next 10 years it is anticipated that mining will be carried out to a depthof 3,200 ft below the surface. The rapid extension of the mine has necessitated frequent re-appraisals and modifications to the primary ventilation system, and a system with considerable in-built flexibility has gradually evolved. Since 1953, volume circulation has increased eight-fold to approximately 2,400,000 c.f.m.To suit various mine operating requirements, a combined pressure-exhaust system of ventilation was adopted.The usefulness of this system is at a maximum when the fans installed permit ready changes in the location of the boundary between adjacent spheres of fan influence.Air flow through openings to the surface can be controlled or used as required. This feature is considered necessary for a mine where underground workings are comparatively shallow and caving to the surface willoccur.A major heat problem exists due to climate conditions, high geothermic gradient (one degree Fahrenheit in 95 ft), and oxidation in leached and brecciated areas.Because of this, quantities of air far in excess of the minimum requirements for dust removal are required to ensure satisfactory environmental conditions. In assessing fan pressure, consideration was given to 1. the mine resistance, and the requirement for pressure differential capability,2. the pressure requirement for deeper mining, with due allowance for booster fan use where appropriate,and3. the desire to avoid fan operation at pressure duties above the region of peak fan efficiency.The latter feature provides a safety margin between maximum operating pressure and the stall point of the fan.

Jan 1, 1967

By C. Eswaraiah

A drop weight tester (DWT) is designed and fabricated for the purpose of analyzing single particle impact breakage characteristics of different ores. The test results were evaluated through the breakage distributions of different size fractions at five different input energy levels. The breakage parameter, t10 (Narayanan, 1986) is used to represent the degree of size reduction, which is assumed to be representative of the breakage product size distribution obtained from single particle breakage. Representation of breakage distribution with this method consist one more breakage dependent parameter (a). To evaluate the impact breakage characteristic of different ores, a mathematical relationship was established to analyze the dependency of breakage parameters, t10 and a on specific input energy (EIS) or fracture energy (Tavares et al, 1998, Fandrich, 1998), specimen size (?) and Bond?s operating work index (WI0). Mathematical results developed gives adequate model for all ball mill modeling. It can be concluded that the drop weight test method is a useful and practical way of evaluating the impact strengths of various ores and results of which can be used in modeling mills.

Sep 1, 2012

By G. Mawire

The extraction of scandium from its oxide with a task specific ionic liquid [Hbet][Tf2N] offers potential advantages of lower energy consumption, recycling of the extractant and reduced environmental impact compared to conventional methods. In this paper, the influence of reaction temperature, solid to liquid ratio and water to the ionic liquid ratio on the extraction of scandium from a synthetic scandium oxide (Sc2O3) system was studied. The influence of investigated parameters on leaching was very significant as approximately 98% scandium was extracted from its oxide after 72 h. Furthermore, the ionic liquid also selectively extracted 47% scandium after 48 h from a mixture of pure metal oxides containing oxides of tantalum, niobium, and scandium. The research demonstrated the potential of [Hbet][Tf2N] to selectively extract scandium from columbite processing tailings and other scandium bearing ores like Ixiolite, Heftetjernite and Tantalite which predominately contain tantalum and niobium.

NEW MEMBERS The following list comprises the names of those persons who became members during the period Dec. 10, 1916 to Dec. 31, 1916. BOWMAN, Joseph V., Chem., Andes Copper Mining Co., Chanaral, Chile, South America. CALDER, NORMAN L., Min. Geol., Cia. Minera y de Fomento, Watkins, Fomento Prov. de Santa Clara., Cuba. CONRADS, RALPH A., Met. Engr., Magna Plant, Utah Copper Co., Garfield, Utah. FARR, T. H. POWERS, JR. Asst. Assayer, Argonaut Mining Coy Jackson, Cal HAURY, PETER S., Min. Engr ...Alta Loma, Cal. HOULE, ARTHUR, Supt., Shattuck-Arizona Copper Co., Box 2009, Bisbee, Ariz. LEIB, VICTOR E?, Min. Engr 4204 Ave. D, Austin, Tex. LINDSLEY, THAYER, Min. Engr 82 Beaver St.,. New York, N. Y. POTTER, OCHA Supt., Superior Copper Co., Houghton, Mich. ROCCA, BERNARD T.; Engr., Bluebell Mine, Cons. Arizona Smelting Co., Mayer, Ariz. SAFFOLD, RAY P P.'0. Box 436, Douglas, Ariz. THOMS, JAMES EZRA, Asst. Chief, Milling, -Roasting, Acid Depts., Mineral Point Zinc. Co., Depue, Ill. TOMITA, HARUYOSHI, Met. Engr., Mitsubishi Co., Osaruzawa Mine, Akita-ken, Japan.

Jan 2, 1917

By Leiner Novaes Arêdes

Após o bobinamento com temperatura controlada, as bobinas são resfriadas até um valor próximo da temperatura ambiente para o processo de decapagem. Há uma bibliografia farta no que diz respeito à temperatura de bobinamento e seus efeitos nas propriedades mecânicas e na microestrutura do aço plano laminado a quente. Contudo, pouco se encontra sobre a influência das taxas de resfriamento pós bobinamento nas propriedades mecânicas e na microestrutura do aço, especialmente nas propriedades finais de materiais que são submetidos à laminação a frio e recozimento. O tempo médio de resfriamento com água é de dois dias. Já o tempo para resfriamento com ar é de sete dias. Estudou-se o efeito das referidas taxas na microestrutura e nas propriedades mecânicas para um determinado aço tanto após a laminação a quente como após a laminação a frio e recozimento.

Jul 30, 2018