Search Documents

By W. C. Ellis, M. E. Fine

In the iron-cobalt system there are several property-composition relationships of theoretical importance. The alloys are ferromagnetic exhibiting a maximum saturation at approximately 33 at. pct cobalt;' the interatomic distances at room temperature show large positive deviations from Vegard's rule;2 and in the region of 50 at. pct cobalt there is an order-disorder transition2 which has a large effect on other properties. The thermal expansion data for the system have been reported only from room temperature to 100 C and for this temperature range a minimum in coefticient in the rcgion of 50 at. pct cobalt is well established.3,4,6 This paper reports the expansion properties in the iron-cobalt system for temperatures from 30 to 850°C, shows the correlation with other physical properties, and proposes an explanation for the tcrrelation. Experimental Procedure The thermal expansivities of iron-cobalt alloys in 10 pct steps in composition were determined from 30 to about 850°C. The major series of alloys was prepared by induction melting from Armco iron and cobalt rondelles with the addition of about 0.6 wt pct manganese. This series was supplemented by three compositions: high purity electrolytic iron, high purity electrolytic cobalt, and an alloy of 52.1 wt pct cobalt prepared from the high purity electrolytic iron and electrolytic cobalt by vacuum-melting. The compositions of both series of alloys are given in Table I. The specimens for measurement were prepared from the cast ingots by first hot-swaging followed in most instances by cold-swaging to 0.180-in. diam rod. Some alloys in the region of 5c pct cobalt, because of inherent cold-brittleness, were swaged hot to the final diameter. The expansion specimens were approximately 2 1/2 in. long with flat-ground and polished ends. Before measurement they were annealed in hydrogen for I hr at 900°C. In the apparatus used for the thermal expansivity measurements (Fig I), a modification of that designed by Hidnert and Sweeney,? the differential expausion between the specimen and vitreous silica was measured by a dial micrometer reading to 0.001 mm. An invar fixture supported the dial gauge, and this fixture, in turn, was connected to a split invar collar which supported the outer silica tube. A pyrex "T" was placed over the outcr silica tube and was sealed to the invar collar by Apiezon Q sealing compound. A movable hollow vitreous silica rod which rested on top of the test specimen slid through a flexible rubber diaphragm cemented to the top of the pyrex "T." The specimen rested On a vitreous silica pedestal fused into the outer tube and was kept centered by a silica sleeve. A nonoxidizing atmosphere was obtained by admitting hydrogen into the

Jan 1, 1949

By R. W. Bartlett

Hydrometallurgical processes for copper flotation concentrates avoid the SO2 emission problems associated with smelting, but they require oxidation of copper to obtain solubilization during leaching. The resulting copper ions must be reduced to metal, which normally requires large amounts of energy or energy equivalent reagents such as hydrogen or iron. The conventional reduction method is electrowinning which is labor intensive and involves 35 to 40% of both the entire operating and capital cost of the better hydrometallurgical processes. There is considerable incentive to reduce the cost and energy required for producing copper ions from solution. Furthermore, it is thermodynamically possible to do this using sulfur contained in the concentrate itself. In fact, the thermodynamic potential of oxidizing sulfur from S+4 to the S+6 state is greater than required to reduce cupric ion to metallic copper.1 Realization of this potential in a practical process would significantly reduce the cost of hydrometallurgical processing of sulfide concentrates because sulfur would become a cost-free reducing agent. An apparently practical method is to use SO: and HSO3 ions, obtained by ammonia scrubbing of SO2 from a concentrate roaster gas, to reduce leached copper to metal in an autoclave. This reduction step is the Jumau 1907 A series of steps, including sulfite reduction, constituting a crude flowsheet was suggested by Parker in 1976.3 The present paper describes a detailed complete. sulfite process flowsheet based on materials and energy balances, discusses the chemistry, and discusses further work that is required to develop this process. Process materials, utilities costs, and energy requirements are projected to be unusually low because of the utilization of sulfur from the concentrate. Process Description The sulfite reduction process requires a copper concentrate containing approximately as much sulfur on a weight basis as copper. For those few concentrates that are deficient in sulfur, additional sulfur can generally be obtained by allowing more pyrite to float in the concentration process. The process steps, shown in [Fig. 1], are (1) a fluid bed roast of the concentrate, (2) a leach of the roaster calcine using recycled barren liquor from the reduction autoclave, (3) scrubbing of the SO2 gas with ammonium sulfite liquor to produce ammonium bisulfite, (4) reduction and precipitation of copper in an autoclave by combining part of the SO2 scrubber effluent (SO5

Jan 1, 1980

By Leonardo Martins da Silva

O minério de ferro quando encontrado contendo teores do elemento fósforo acima de 0,05% é considerado rejeito dada sua inutilização para o processamento de fabricação do aço. Tal fato ocorre devido a elevação da dureza do aço tornando-o quebradiço e com fratura. Sendo assim o presente trabalho tem como objetivo a avaliação do efeito do processo de lixiviação ácida como finalidade de redução do teor de fósforo no minério de ferro. Através da utilização do software Termocalc® foi possível analisar as diferentes estruturas formadas em diferentes teores do elemento fósforo. Através da técnica de microscopia eletrônica de varredura (MEV) foi possível analisar a estrutura do minério de ferro após seu tratamento com a energia de micro-ondas. Por meio da técnica de planejamento estatístico fatorial com pontos centrais e axiais foi possível determinar as condições ótimas de remoção de fósforo através da técnica de lixiviação ácida.

Aug 1, 2018

By P. N. Anyalebechi

The effects of Si (0.19-0.52 wI. %), Fe (0.20 wI. %-0.44 wI. %), and Cr (0-0.10 wI.%) on the response of ingots of aluminum alloy 3004 solidified at different rates (O.IO°C/s to 30°C/s), to homogenization heat treatment have been investigated. Response to homogenization was determined by quantifying the following microstructural parameters: (i) amount of Mn retained in solid solution; (ii) types, relative amounts, sizes, size distributions, shapes, and chemical compositions of second phases; (iii) extent of the alpha-transformation (i.e., AI6(Fe,Mn) --7 (XAI12( Fe,MnhSi) reaction; (iv) dispersoid formation; and (v) alleviation of dendritic microsegregation. Of the three alloying elements investigated, Si had the greatest effect on the response of aluminum alloy 3004 to heat treatment. Increase in Si content, fineness of cast microstructure, and homogenization temperature facilitated alpha-transformation reaction, dissolution of Mg2Si, loss of Mn supersaturation, and formation of AldFe,Mn)3Si and Mg2Si dispersoids.

Jan 1, 2008

Report M294 A mineralogical investigation of potential gold-sorbing minerals and shales, by c.T. Logan. Dec. 1986. 12 pp. Computer software The Fifth IFAC/IFIP Symposium on Software for Computer Control (SOCOCO 88) is to be held in J ohannesburg from 26th to 28th April, 1988. Tunneling 88 The Institution of Mining and Metalurgy, with the cooperation of the British Tunneling Society, the Institution of Mining Engineers, and the Transport and Road Research Laboratory, Department of Transport, is pleased to announce the fifth international symposium, Tunneling 88, which wil be held in London, England, from 18th to 21st April, 1988. Ion-exchange processes ION-EX '87, an international conference and industrial exhibition on the industrial, analytical, and preparative applications of ion chromatography and ionexchange processes, wil be held in Wrexham (North Wales) from 13th to 16th April, 1987.

Jan 1, 1987

By H. Zhu, Q. Jiang

The leaching kinetics of iron during the atmospheric direct leaching (ADL) of marmatite concentrate was studied under the following conditions: reaction temperature of 343-383 K, slurry pressure of 0.3-0.7 MPa, particle size of (-74 ?m, +63 ?m), (-63 ?m, +44 ?m), (100%-44 ?m). The statistical effects of reaction temperature, total pressure and particle size of concentrate on the extraction and the leaching rate of iron were analyzed. The results show that reaction temperature is a significant factor while slurry pressure and particle size are not statistically meaningful with respect to the extraction or the leaching rate. The extraction of iron fits better to the mixed-controlled shrinking core model and the apparent activation energy was calculated to be 37.66 kJ/mol. The leaching of iron is mixed controlled by the interfacial chemical reaction and diffusion across the product layer.

Jan 1, 2014

By Ranieri Corrêa Salazar

Essa contribuição técnica mostra a evolução do processo da Linha de Recozimento Contínuo de Chapas (LRCC#1) da Companhia Siderúrgica Nacional (CSN), na produção de laminados a frio sem revestimento para o segmento de mercado de tambores. A CSN vinha ao longo do tempo perdendo esse mercado devido principalmente a problemas de qualidade, como oxidação quando realizava a laminação de encruamento seca e, por outro lado quando processava o material com laminação de encruamento com óleo protetivo, ocorria no processo do cliente de cura a incompatibilidade com a tinta e vernizes nas aplicações mais críticas como acondicionamento alimentício, farmacêuticos e outros, cujos requisitos de qualidade rigorosos são exigidos contra qualquer tipo de contaminação. Desenvolveu-se um produto que associado ao controle de sua quantidade e a microgeometria da superfície da tira, resultou na lubricidade necessária para a continuidade operacional e atendeu aos requisitos de qualidade desejados.

Jul 30, 2018

By Gian San Ana d Ávila, Rodrigo Marcelino Guilherme, Bruno de Alcantara Monteiro, Rafael César de Souza, Denilson de Souza Braga

O Objetivo deste trabalho é apresentar a implantação inovadora de testes das proteções intrínsecas nos Gasômetros de gás de Alto Forno (BFG) e gás de Aciaria (BOFG) denominado de "Testes Espoleta", no qual são realizados testes a quente de todas as proteções existentes, estando os gasômetros em operação normal e conectados ao processo produtivo. Estes testes foram idealizados a partir de benchmark com empresas do setor siderúrgico em função do acidente ocorrido com um gasômetro em 2018 no Brasil, e principalmente durante os trabalhos desenvolvidos por um grupo de trabalho multidisciplinar em conjunto com a consultoria especializada em Análise de Riscos de Processo (ARP). Como resultado deste trabalho, foi definida uma recomendação de testes no sistema de proteção após classificação de grau de risco 1 (Gravidade/Probabilidade) do perigo de explosão / incêndio em caso de falha nas proteções dos Gasômetros e as redundâncias existentes.

Aug 1, 2019

By G. W. Jones, F. E. Scott, R. E. Kennedy

Methylene chloride , dichloromethane CH2C12 , a low - boiling and highly volatile organic chlorinated compound, is used extensively as a refrigerant in air conditioning installations , as an intermediate in organic synthesis , and as a solvent for cellulose acetate and other materials . As its vapors are not inflammable in air at ordinary temperatures , it can be used to advantage where it would be highly dangerous to use ordinarily inflammable solvents . The question has been raised as to its inflammable range in pure oxygen and in air enriched with oxygen . To find the answer to this question, tests were carried out with various mixtures of methylene chloride , oxygen, and nitrogen mixtures . It was found that methylene chloride has wide limits of inflammability in pure oxygen . Additional tests were then made to establish the complete range of inflammability of these gases . The methylene chloride employed in the tests was cbtained from the Eastman Kodak Co. It had a reported boiling range of 40.5 ° to 42.0 ° C. and a density of 1.322 at 20 ° C.

Oct 1, 1943

By Paulo Ricardo Bastos de Queiroz

Após estudo realizado, verificou-se que a CSP - Companhia Siderúrgica do Pecém, possuía alta vulnerabilidade às oscilações de frequência, sejam elas oriundas de falhas nas unidades geradoras ou problemas nas linhas de transmissão que compõem o SIN (Sistema Interligado Nacional), onde tais perturbações poderiam provocar desde a parada total da planta a danos irreversíveis em equipamentos como motores síncronos. Com base nesse estudo, foi implantado um sistema automatizado e de rápida resposta capaz de diminuir ou eliminar todos os efeitos provocados por tais distúrbios, atuando de forma dinâmica e coordenada com o cenário energético ao qual a planta siderúrgica encontra-se no momento do evento. Dentre os ganhos apontados em estudo, destaca-se a confiabilidade de se ter um sistema de distribuição de energia em uma usina siderúrgica capaz de assegurar a continuidade do processo ou em piores casos proporcionar uma parada emergencial com total segurança.

Oct 30, 2017

By Alonso Cepeda, Ignacio Ramos, Enrique Garay

El proyecto Fenix Gold está ubicado en la parte norte de la franja Maricunga, a 120 km de la ciudad de Copiapó en la región de Atacama, Chile. El estudio de prefactibilidad concluido el año 2014 reporta un recurso medido más indicado de 434 Mt con 0.38 g/t Au que contiene 5.25 Moz Au, y un recurso inferido de 58 Mt con 0.32 g/t Au que contiene 0.6 Moz Au. Considerando el recurso medido más indicado se estimó una reserva de 294 Mt con 0.4 g/t Au que contiene 3.7 Moz Au. Se prevé que será una mina a tajo abierto y el oro se recuperará por un proceso de lixiviación convencional. La mineralización aurífera ocurre en la parte alta de una diatrema ubicada en el centro de un volcán del Mioceno Inferior. La mineralización de oro está controlada por estructuras NW y EW de alto ángulo y se manifiesta como venillas bandeadas de cuarzo negro y venillas de cuarzo pirita, el cuarzo es generalmente ópalo y/o calcedonia. Desde el punto de vista geoquímico, la mineralización de oro no está asociada a ningún elemento contaminante. La alteración hidrotermal es muy débil, los feldespatos se alteraron a esmectita e illita. Todas las evidencias descritas indican que el yacimiento Fenix es de tipo epitermal de baja sulfuración.

May 22, 2019

By Fabiano Rodrigues Soares

O Mandril é um dos mais importantes componentes da laminação de tiras, pois trabalha diretamente na qualidade do produto, tanto para o cliente interno quanto para o cliente externo. Para atender a demanda do mercado de Siderurgia e Alumínio para a área de laminação a quente, a frio e linhas de processo, temos a necessidade de entender os conceitos existentes e desenvolver novas formas para aumentar a performance do equipamento, resultando em menores gastos com manutenção e um menor número de tempo parado da linha, culminando em lucro para a empresa. Será apresentado neste trabalho tecnologia em reengenharia e projeto de Mandris, aplicando know how adquirido dentro de vários anos de experiência e ainda contando com o apoio tecnológico de nossos colegas da Alemanha com soluções de excelente qualidade para o cliente. Estas soluções podem ser através de novos materiais, novos revestimentos e novos conceitos de trabalho do equipamento.

Oct 30, 2017

By Claude W. Sill

In the usual volumetric determination of uranium, the solution containing uranium is reduced in a Jones reductor, yielding a mixture of trivalent and tetravalent uranium; the trivalent uranium is oxidized to the tetravalent state by bubbling a stream of air through the solution. The resulting solution of. Tetravalent uranium is titrated with a standard oxidant, generally sulfatoceric acid, dichromate, or permanganate; It seemed likely that the, same general procedure could be used in determining semimicro quantities of uranium if the conditions affecting the variables involved were understood more clearly than at present. In the method described below, the use of ferric sulfate to oxidize tetravalent uranium allows the titration to be made at room temperature in an essentially colorless solution with sulfatoceric acid. The latter oxidant its turn permits the use of the very stable indicator, ferroin, with its sharp color.., change and exactly reproducible blanks. Solutions of uranyl sulfate were prepared by diluting a stock solution that had been standardized gravimetrically according to the method of Lundell and Knowles (8).3/ Solutions of sulfatoceric acid were prepared according to the directions of G. F. Smith (12) and were standardized against arsenic trioxide in the presence of osmic acid according to the directions of Gleu. The cerium solutions were stored in 18-liter carboys fitted with siphon arrangements so that the bottles did not need to be opened and protected from light in a dark cupboard. Under these conditions, even the 0.01 N solution changed by less than 1 part per thousand over a period of about 6 months.

Jan 1, 1952

COUNCIL The following served on Council during the year under review: Office bearers: Messrs V. C. Robinson (President), Prof D. D. Howat and Dr J. P. Hugo (Vice-Presidents), J. K. E. Douglas (Immediate Past President) and D. G. Maxwell (Honorary Treasurer). Ordinary Members of Council: Dr M. G. Atmore, Dr J. M. Bereza, H. P. Carlisle, W. W. Malan, C. E. Mavrocordatos, Prof R. P. Plewman, Dr R. E. Robinson, Dr M. D. G. Salamon, P. W. J. van Rensburg, L. W. P. van den Bosch, P. A. von Wielligh. Branch Chairmen: J. Meintjes, J. M. Meyer (Acting), J. N. Saunders (Retired). Past Presidents serving on Council: R. J. Adamson, M. Barcza, H. Britten, R. C. J. Goode, P. Lambooy, Prof J. de V. Lambrechts, Dr J. T. Mclntyre, J. F. Reid, H. Simon. Ten Council meetings were held during the year with an average attendance of eighteen and the standing committees held forty-six meetings. FINANCE The annual accounts, which are attached to this report, show an excess of income over expenditure of R5 051 compared with an excess of expenditure over income last year of R4 608. This major reversal of fortunes is due in the first instance, of course, to the increased subscriptions. There were, however, other important contributors, particularly sales of the Proceedings of the Symposium on Open Pit Mining and profits on the operation of symposia and colloquia. It would appear from a study of the accounts that there has been a substantial drop in expenditure on secretarial fees. In actual fact, however, our total expenditure on secretarial fees was higher. A portion of this expenditure was charged against the administration of the Symposium on Open Pit Mining and, in addition, the charge against the Journal accounts for secretarial fees was increased. It will be recalled that in last year's annual report it was mentioned that subsequent to the new arrangement for publication of the Journal, the expected improvement in the finances of the Journal had been slow in materialising. After a total period of 18 months there was still no sign of improvement and it was accordingly decided to end the arrangement. As a result, the drain on the finances of the Institute was considerably lessened in the second half of the year. During the course of the year Council became concerned about the rapid depletion of our accumulated funds and gave careful and detailed attention to all aspects of the Institute's financial affairs. Particular attention was given to: 1. The fact that the Institute does not have a solid financial backing and must appeal for funds every time any special event such as a symposium is held. 2. The responsibilities of the Institute to the profession and the community, with particular reference to the desirability of establishing Institute bursaries and participating in other educational activities. 3. The rapidly rising cost of living. 4. The immediate financial position of the Institute. 5. The rapidly increasing cost of publishing the Journal due to the increasing number of papers available. In the meantime the immediate financial position of the Institute has improved but as this is due largely to non-recurring or irregular items of revenue, it should not be given undue weight. After careful consideration it was decided that an appeal should be made to industry for financial assistance, which would be used to cover the cost of symposia and other unusual expenditure and also, if possible, to build up the capital resources of the Institute so that there is a solid foundation for the future. Before appealing to industry, Council wished to be quite certain that there could be no criticism of the Institute for not having done our best in a personal capacity. Furthermore, Council examined many comparative statistics, including those circulated to members, which showed that, while expenditure per member has risen at an average annual rate of 7,5% over the last fifteen years, subscription revenue per member has risen at only 3,4% per annum. It was with this background that your Council decided to raise the subscriptions. Initial approaches have been made to the big mining groups and there has been a very generous response, although the details of how financial assistance will be provided have not yet been worked out. It seems likely that some form of affiliated company membership will be the most suitable method of achieving this. When these details have been fixed, it is the intention to extend the appeal to all corners of the mining industry as well as manufacturing and metallurgical industries. It is believed that these measures will ensure that the finances of the Institute are placed on a firm foundation on which the expanding activities can be planned. The MacArthur Forrest Memorial Fund shows an excess of income over expenditure of R73 and the total fund was, therefore, increased by this amount to R4 411. The balance sheet shows that the market value of quoted shares and debentures increased during the year fron R6 540 to R9 160. The market value is now almost exactly the same as the book value. Accumulated funds now amount to R23 010 compared with R17 959 a year ago.

By Thiago de Morais Gomes

Este trabalho trata-se de uma pesquisa bibliográfica com o objetivo principal de analisar o impacto das diferentes propriedades que podem ter as pelotas de minério de ferro e seus comportamentos no processo de produção de gusa no alto-forno. São destacados conceitos e definições gerais sobre o tema, bem como exemplos de processos. Para tanto, foi realizado uma seleção bibliográfica em vários artigos, livros e portais da Internet, cujos autores subsidiaram na compreensão dos principais assuntos relacionados ao tema. Concluiu-se que existe a necessidade de se realizar um processo de seleção de pelotas com determinados tipos de propriedades para a produção de gusa no alto-forno, com isso reduzindo a quantidade de escória e aumentando o desempenho do alto-forno. Também existe a necessidade de novos estudos sobre este tema devido a escassez de artigos e livros que tratam especificamente deste para a siderurgia.

Aug 16, 2017

By F. Milton Lewis

In this paper an attempt has been made to review the cost trends in producing copper by conventional milling. smelting and hydro-metallurgical means during the last five years. The primary objectives of this cost analysis are to provide a base for future projections as well as to indicate which cost items are more volatile in their influence on overall cost of producing copper.

Jan 1, 1977

By Fred D. DeVaney

The Mesabi iron district of Minnesota has a potential production of over 50 million tons of iron are annually. The large shipments of ore each year are gradually depleting the reserves, and if the present rate of production is to be maintained there must be a growth in the present available ore supply. Growth is a natural course. The growth of a city may be affected by the addition of city blocks or by the improvement of utilities necessary for its betterment. These may go on in the order named or concurrently. The city-block type of growth of the Mesabi has been tremendous, and the "betterment" type has followed in due course. Probably the former has reached its limit, and if so, more time will be allotted to the latter. It is not the in¬tent of this paper to present either a eulogy of the wonderful mining methods or a history of the milling, but it is pertinent to say that if the lean-ore area continues to produce, the continuance will be more the result of further improvement of milling methods non well under way than of extension of boundaries by the city block plan of growth.

Jan 1, 1932

By Gary L. Mowrey

Visible and sometimes audible indications of excessive underground rock pressure such as pillar fracturing, squeezes on chocks, and "roof talk" are familiar to mining engineers. Such signs often precede rock failure on a larger scale and therefore may be used as a warning. Nevertheless, these subjective observations do not provide an adequate means of evaluating the existing rock pressure conditions in a mine. One method which appears to be extremely promising in determining the stability of geologic structures in general is that of monitoring their associated micro seismic activity. Mining engineers generally agree that during the process of rock deformation and failure small-scale seismic ("microseismic") vibrations are produced in the rock itself. These transient vibrations propagate through the rock structure and may be detected at a considerable distance from the failed rock by employing suitable electronic monitoring equipment. Hardy (1) has presented a detailed review of microseismic research in the mining, petroleum, and geoscience areas, and it is apparent that relatively little application of micro seismic techniques have been made in coal mines. This is especially true in North America since here most coal mines are fairly shallow and consequently are not generally subjected to excessive stresses. Furthermore, strict Federal and State mining laws limit the use of electrical equipment in coal mines complicating the use of the necessary monitoring facilities. In terms of both mine safety and economics, monitoring microseismic activity appears to be invaluable in the detection and location of over-stressed pillars and unstable roof conditions caused by development and production work. In 1970 The Pennsylvania State University Rock Mechanics Laboratory became involved in a research project, sponsored by the U.S. Bureau of Mines, to investigate the feasibility of using microseismic techniques to detect and to locate potential regions of instability around a longwall coal-mine operation [Hardy and t10wrey (2); Mowrey (3)]. In this study geophones (velocity gages) located in an array of shallow boreholes drilled from the surface above the active area of the longwall were employed to detect microseismic activity, and a mobile micro-seismic monitoring facility was used to condition and record this data for later analysis. This project is unique in that measurements were made from near-surface geophones rather than geophones installed on the mine itself. Two advantages are apparent, namely that (1) there are no electrical limitations on the monitoring system and that (2) mining operations can continue normally because there is no monitoring equipment or cables in the mine.

Jan 1, 1978

By R. Cottam

The deformation and recrystallisation of magnesium yttrium alloys containing 0.23, 0.84 and 2.71wt% yttrium and commercially pure magnesium extrusion has been investigated at temperatures between 200 and 350°C. The alloys were produced as billets 7.5 cm diameter, solution treated at 525 °C for 8 h and extruded into 3 cm diameter bar at 390°C. Channel die compression was employed to deform the samples at a strain rate of 1x10-3s-1. For the 0.23 wt% yttrium alloy and the pure magnesium, dynamic recrystallization (DRX) occurred at all temperatures and the amount of DRX increased as the temperature was raised. In the alloys containing 0.84 and 2.71 wt% yttrium DRX was almost completely suppressed at all temperatures. The absence of DRX in the 0.84 and 2.71 wt% yttrium alloys was accompanied by a decrease in the ductility, except at 350°C the highest deformation temperature. It was observed that this increase in ductility was accompanied by a reduction in deformation twinning and the initiation of pyramidal slip. This work highlights the important role that DRX plays in enhancing the ductility of magnesium alloys.

Jan 1, 2006

By Chen Jianhua, Shen Zhenchang, Zhang Ming, Chen Feifei

"With flotation cells scale-up, the performance of flotation cells is increasingly variated for short-coming and dead zones existing. The residence time distribution which shows the movement of tracers can assess the unexpected flows such as short circuit and dead zone in a flotation cell. In this paper, the residence time distribution of pilot flotation cell is investigated with CFD simulation. Based on the theoretical model, the short-coming probability and dead zone probability are quantitative. The ideal average residence time is similar with the actual average residence time. The mixing effect of the flotation cell approaches the ideal continuous stirred tank reactor. The operating parameters such as speed and feed velocity have complicated influence on residence time distribution. The research would be helpful to understanding flow in flotation cell and improving performances of flotation cell.INTRODUCTIONFroth flotation is a method which purifies minerals according to difference of physical and chemical surface characters of different mineral particles (Shen, Z., Chen J, 2012). Flotation cell is a key equipment for froth flotation method. The flotation cell performances have great influences on flotation index.It is difficult to evaluate flotation cell how to improve flotation procedure to complexity.The main flotation cell performances are aeration volume, air dispersion, solid suspension and residence time distribution, etc (Shen, Z., Lu, S., 2008). Residence time distribution is an important fluid hydrodynamics which could reveal the flow of pulp, mixing of particles and air bubbles. In the flotation cell, the ideal average residence time of pulp could obtain easily. But the fluid differential units would be different flow paths. The residence time of the fluid differential units is variation and would be longer or less than the average residence time. The residence time distribution would reveal the mixing effect and predict the not ideal flow in the flotation cell such as shorting cutting, dead zone, etc. As we know, the shorting cutting and dead zone would be decreased the real flotation time and it is disadvantage to better flotation effect, especially for large flotation cell. It is impossible to eliminate the not ideal flow totally. It is very important to reveal and decrease the shorting cutting and dead zone probability in the flotation cell."

Jan 1, 2018