Search Documents

By G Lane, S Morrell

The design of the 12 m diameter SAG mill installed at the Cadia Hill Mine in New South Wales followed after two years of extensive laboratory and pilot plant testwork. The testwork showed the Cadia ores to be hard and competent necessitating the use of both a variable speed SAG mill drive and pebble crushing. The grinding power requirements for the SAG mill was based on engineering in-house grinding software, pilot plant data and simulations using JK SimMet software. Surveys of the SAG mill operation during the first four weeks showed the feed size distribution, transfer size and pebble rate to be lower or less than those for which it was designed. To compensate for the lower pebble rate, the SAG ball load was increased. This resulted in the total comminution circuit power being some 0.5 kWh/t higher than predicted. The JK SimMet SAG model has been modified to take account of these variations.

Jan 1, 2000

By Henry A. Stiff, J. P. Hammond, A. B. Westerman, H. C. 195-000-000-014 Cross, and Lawrence E. Davis

The phases in Cr-Fe-Mo alloys have been investigated with homo-genization, aging temperature, composition range, and alloy addition as variables. Metallography, three X-ray methods, and hardness were used as methods of study. The behavior of s, M23,C8, and Z phase are reported for cornpasition range 60 pct Cr-15 to 25 pct Fe-15 to 25 pct Mo-<0.005 to 0.36 pct C with aging at 1400º to 2000°F. With 2 pct Ti, Tic and TiC-TiC are formed; with nitrogen Cr2N. THE recently developed class of chromium-base heat-resistant alloys shows appreciably higher strength than commercially used high temperature alloys. However, further developmental work is required to impart needed shock resistance and some degree of room-temperature ductility to these alloys. Extensive exploratory work on chromium-base alloys was begun in a program initiated by the War Metallurgy Committee of the National Defense Research Council at the Climax Molybdenum Co. in the early part of 1942.&apos; Alloys were sought for gas-turbine blades for use at 1600°F. A minimum of 5 pct elongation in the stress-rupture test was a requirement. From the Climax work, ternary alloys of chromium, iron, and molybdenum appeared to show the greatest promise as materials for gas-turbine blades. The composition line in the ternary diagram joining the 60 pct Cr-15 pct Fe-25 pct Mo and 60 pct Cr-25 pct Fe-15 pct Mo alloys was indicated as representing the most useful combination of strength and ductility.&apos; Strength increased while ductility decreased as molybdenum was raised in this composition range.&apos; The 60 pct Cr-15 pct Fe-25 pct Mo type alloy was thought to have the most suitable properties for gas-turbine blades.&apos; Concurrent with the study reported here, other investigations were being made on Cr-Fe-Mo alloys. The liquidus temperatures on a series of low carbon, ternary alloys were being determined, and isothermal sections drawn at 2370°, 2010°, and 1650°F (1300°, 1100°, and 900°C).2 Also, various methods of preparation and some mechanical and physical properties of chromium-base alloys, particularly the 60 pct Cr-15 pct Fe-25 pct Mo type, were being investigated., At the inception of the present program, only a limited study had been made of etchants for developing the microstructures of chromium-base alloys; X-ray analysis of the microconstituents had not been made. A review of the literature revealed that no phase-diagram work had been reported on the Cr-Fe-Mo system. Scope of Work The work on chromium-base alloys includes the following: 1—The development of etching methods for differentiating between the microconstituents; 2—The identification of microconstituents by X-ray diffraction methods; and 3—A comprehensive metallographic and hardness study after various heat treatments. The phases were studied by three standard X-ray techniques: 1—The block-sample focusing-camera method; 2—The powder-diffraction method on elec-trolytically separated residues; and 3—The powder-diffraction method on cold-worked aggregate samples. The results by the first two methods were correlated with the metallographic data. The third method was used largely to study conditions approaching equilibrium, since cold working prior to heat treating accelerated precipitation. Seven types of alloys were investigated: 50 pct Cr-50 pct Fe, 40 pct Cr-40 pct Fe-20 pct Mo, 55 pct

Jan 1, 1953

By Sunny Murmu, Gnananandh Budi

One of the most significant concerns in longwall ground control is the instability and failure mechanism of the coal wall. The current research uses FLAC3D to simulate panel 1 of the Adriyala Longwall Project, India, in order to evaluate the distribution of vertical stress and material failure mode, in and around the longwall face. Additionally, three distinct criteria are used to evaluate coal wall spalling: vertical stress distribution, maximum shear strain, and residual cohesion. A novel algorithm is also proposed to appropriately capture roof bed caving, shield installation and advancement, and coal extraction from the face. The findings of the modelling show that progressive longwall extraction creates an elliptical stress relief zone around the excavation void. During the peak stress phase, the height of the stress relief zone is greatest, whereas the width is highest during the main fall phase. As mining advances, the coal wall at the face line appears to lose its stress-bearing capability. Shear failure was the most common coal wall failure mode. Maximum spalling depth (MSD) and longwall face spalling index (LFSpI) were used to measure the extent and volume of coal wall spalling in FLAC3D. For panel 1 of the ALP mine, the MSD, and LFSpI were determined to be 3 m and 90.5 %, respectively. The mode of coal wall spalling was expected to be total or fragmented failure. The field observations and the numerical modelling findings were in good agreement. The compressive strength and deformation modulus of the immediate roof appear to have a substantial role in coal wall spalling. The results of the proposed numerical simulation exercise can help strata control engineers better detect the risks of coal wall spalling and enhance face control for safe and productive working environment at the longwall face.

Aug 8, 2023

By Lon Santis, Michael Swisdak, John Tatom

The Institute of Makers of Explosives (IME) and A-P-T Research, Inc. (APT) have developed a quantitative risk assessment tool called IMESAFR (IME Safety Analysis for Risk) for managing risk from various activities undertaken in the commercial explosives industry. The first version was completed in 2006 and Version 2.0 of the software was completed in 2012, incorporating several major new features. The platform is now based on a Geographic Information System (GIS), providing a bird’s-eye-view to help visualize facility layouts and risk. Spatial data on potential explosion sites and exposed sites can now be automatically transferred from the images to ease users’ data input. Use of GIS data provides the ability to check facility compliance with quantity-distance (QD) standards such as the American Table of Distances (used by the Bureau of Alcohol, Tobacco, Firearms and Explosives, ATF), the NATO standard (used by Natural Resources Canada and other nations), or a user-defined table. Research conducted and knowledge gained over the last 10 years enabled changes in the algorithms and models that provide greater fidelity and reduce conservatism. Expert users can change global settings to more accurately match actual site conditions and the program runs using either Imperial (English) or SI (metric) units of measure. These changes and other new features are discussed and demonstrated.

Jan 1, 2013

PRESIDENT PRYDE: Any discussion on Mr. Poster&apos;s paper? MR. J. BEVAN: I would like to ask the gentleman how fine the dust has to be to cause an explosion? MR. T. FOSTER: According to the Bureau of Mines, it is claimed coal passing through a 100 mesh screen would be considered fine enough. That is all I can learn from the different bulletins. MR. BEVAN: Will the coal dust be that fine; going back in the empty cars on the tipple in the mine? MR. FOSTER: Possibly a great deal of it would be. MR. BEVAN: Will the coal dust be that fine, going back, in the empty the coal dust going back in the cars on the tipple, and into the mine? MR. FOSTER: In some places, they are wetting the cars at the tipple, -in the Rock Springs District, we have as the trip goes out, they have a big pipe, and they souse the car, and wet the load, and in some places, near the timbers; that helps to a certain extent. That does not absolutely eliminate it all, but it helps considerable. MR. WM. LITTLEJOHN (Utah Fuel Company) : I think we have all listened very attentively to the paper that Mr. Foster has just read. He has brought up a subject rather close to my heart, for a long time. He mentions particularly, the Scofield disaster, which happened the first of May, 1900; two hundred men lost their lives in the explosion; and I think it is generally conceded that is about the first time it had ever been brought to the attention of coal miners or operators that such a thing was possible, namely, a purely coal dust explosion. The term "Scofield disaster" is rather a mistake, in a way; while the mine that exploded at the time is in the Scofield District all right, it is now known, and probably was known at that time, as the Winter Quarters Mine, one of the mines which belongs to the Utah Fuel Company at the present time, and did at that time. This mine

Jan 1, 1924

By Peter F. Weiss

INTRODUCTION Austro-American Magnesite Co. of Radenthein, Carinthia, Austria, is a wholly owned subsidiary of General Refractories Company, Bala Cynwyd, USA, and has been incorporated since 1908. The raw material basis is the magnesite mine on Millstatt Alp, located in the mountains near Radenthein at an altitude of 1500 m above sea level. The mined crude magnesite is crushed in a surface crushing plant to minus 35 mm and consequently hauled to the processing plant in the valley by means of a cable conveyor of 7.5 km length. The annual production of 350,000 mt is accomplished with 20 supervisors and 122 workers (of those 60 are in the mine). The labor requirement for block caving is 0.2 man hr/mt, corresponding to an output of 40 mt/man/ shift. GEOLOGY The rock in this area mainly consists of crystalline type schist. There are mostly coarse crystalline garnet mica schists with varying mineral concentrations, and to a lesser degree, some deposits of amphibolite and marble. This petrographically rather homogeneous rock is divided into numerous different tectonic units (covers and scales). The magnesite deposit itself is a foreign body that also has been tectonically inserted. The ore body has a length of 600 m, is 450 m deep, and has a thickness of 60 m on average, varying substantially however, The contact with the accessory rock is very precise. The deposit 1 = ore body, 2 = previous open pit, 3 = caved in area, 4 = block under excavation, 5 = land slide consists of coarse crystalline magnesite in excess of 90 per cent. The few impurities consist of dolomite and talc. The lower part of the deposit is inclined parallel with the schists at approx. 40 degrees. In profile it can be seen, however, that the upper part of the deposit has been tilted over. This is a result of a post-glacial land slide reaching from the bottom of the valley at 1400 m above sea level to the peak of the mountain at 2100 m above sea level. Due to this land slide, with horizontal movements of up to 100 meters, as well as older tectonic events, the rock was crushed to a vast extent. Through mining, the land slide was reactivated; about 40 million cubic meters of rock slowly flow downhill almost like a plasticized mass. Near the surface, the rock is completely crushed and resembles a glacier rupture zone. This renders the originally impermeable rock completely water permeable so that practically all of the annual quantity of 1000 to 1100 mm of precipitation permeates the rock and flows down into the mine. The carbonate rock turns into the preferred aquifer. From 1700 to 2600 cubic meters of water have to be pumped from the mine daily. On one hand, additional problems are caused by the water in the mine, on the other hand we have learned to make use of the down- hill pressure forces to improve the crushing process during block caving. The boundary of the downhill shearing zone moves downward as mining goes deeper.

Jan 1, 1981

By Jerry J. Gray

The utilization of secondary titanium was determined in a study by the Bureau of Mines, and a 10-year statistical table showing supply and distribution patterns is presented in this report. Over the total 10-year period, estimated scrap consumption is larger than estimated scrap supply. Trends from the estimated data indicate that titanium is in short supply and probably will continue to be in the future. Because of higher processing costs for recycle scrap, scrap will tend to migrate to the steel and aluminum industries and to ferrotitanium production and exports. Nonrecoverable losses of titanium metal during processing was determined to be a potential area for research.

Jan 1, 1971

By Ludwig Schmidt

The consumption of gasoline in the United States varies materially with the seasons; during some of the summer months it exceeds the rate of production and in the other seasons the production of gasoline exceeds the consumption, The usual practice of the larger refiners is to store surplus stocks during the winter season in order to meet the heavy demands during the summer months. The following table shows the stocks of gasoline at refineries on the last day of April for the past five years: 1919 593,616,170 gallons 1920 643,5526644 " 1921 747,222,900 " 1922 892,567,766 " 1923 1,336,417.871 "

Jan 1, 1923

By Harry Holle, Gary Johnson

A plant trial was conducted at the Paddy's Flat plant of Dominion Mining Limited with the aim of comparing the ef evenness of oxygen and hydrogen peroxide as leaching oxidants. The Paddy's Flat plant is designed such that the leach train can be divided into two parallel streams, allowing the same or lurry to be eated in two identical trains. By effectively ehminatmg the influence of the ore variations on the results subtle differences in the performance of the two reagents hav been identified. . . The results of the plant trial indicate that the two reagents act m different ways, and that each may be more suitable than the other _for _the treatment of certain types of ore. In some cases a co bmation of the two reagents may be the most cost effective option. . or t e same chemical conditions in the leach pulp, including dissolved oxygen levels , the reagents achieve different gold leaching rates, and in some cases different ultimate leach extraction.

Jan 1, 1992

The Students&apos; Organization of the Michigan College of Mines was recognized as an Affiliated Student Society by the Board of Directors of the Institute, at a meeting held on April 28, 1916. At the College of Mines, University of Washington, 30 students and instructors took part in the annual spring excursion early in April. Studies were made of the new reverberatory and casting furnaces at the Tacoma smelter, the Du Pont powder works located on Puget Sound and the Britannia Mining and Smelting Company&apos;s mine and mills on Howe Sound, near Vancouver, B.C. The Britannia mills are using Hancock jigs, Burchart tables and Minerals Separation flotation cells to effect a high recovery on low-grade chalcopyrite ore. The Mining Club, University of. Wisconsin, elected the following officers for the second semester of the present school year: J. G. SKIRM, President, H. L. RAU, Vice President, T. C. SHERWOOD, JR., Secretary-Treasurer, H. E. HODGSON, Mucker, , F. M. WOLVERTON, Assistant Mucker. Theo. C. SHERWOOD, Jr., Secretary.

Jan 6, 1916

By L. Vu, V. Popov, J. Beland, R. Darling

"The Ferderber gold deposit is of Archean age. It consists of a series of gold-bearing quartz lenses within a shear zone that crosscuts the central part of the quartz dioritic Bourlamaque batholith. On average, this zone strikes N70E and dips 65SE. The Ferderber shear zone, which hosts the ore lenses, has been affected by a succession of tectonic events. A possible early period of brittle shear, accompanied by the formation of quartz lenses, resulted from strike slip movement along the zone. These early quartz veins were subsequently folded and boudinaged during reverse movement that accompanied a prolonged period of ductile shear. More quartz veins were emplaced in the shear zone at this time; these were also deformed by the thrusting. The latest tectonic event to affect the shear zone was a period of brittle fracture.Early dextral strike-slip movement on the shear zone is suggested by the local occurrence of Riedel shears, the preferred association of ore with east-northeast oriented segments of the zone, and by the apparent en echelon arrangement of some ore lenses. The most important event, a reverse movement, is indicatedby the attitudesoffoliation, folds, boudins, COS tectonites and slip planes. The late brittle fracturing formed narrow gouge filled faults, locally flanked by brecciazones, whichrun generally within and parallel to the shear zone, and also conjugate fractures that crosscut the zone.The Ferderber and six other adjacent gold deposits were formed in a structural regime dominated by a generally horizontal north-south regional compression. The Y axis of the strain ellipsoid is east-west and varies from horizontal to a plunge of 25 0 w."

Jan 1, 1987

By E. B. Mayo

David LeCount Evans (Consulting Petroleum and Mining Geologist, Wichita, Kans.)-—Not only E. B. Mayo but also W. C. Lacy, who apparently urged the preparation of this analysis, is to be commended. Regional thinking of this type is needed to assure future success in the never-ending search for new mineralized and petroliferous districts. As is usually the case, here is a regional study that will be read by the mining geologist alone. It is ironic that several of the trends established in this study have suggested themselves in northern mid-continent, detailed, and regional studies. These, where established, have offered new keys to petroleum exploration and have provided a possible basis for unraveling a number of broad generalities. The oil geologists, active in Colorado, Kansas, and Oklahoma, would find much food for thought in Mr. Mayo&apos;s projections. To be more specific: 1) The parallelism between E. B. Mayo&apos;s Texas Lineament and the Amarillo Uplift, the Wichita Complex and the Arbuckle Complex of the Texas Panhandle and Southern Oklahoma is viewed with interest and appears especially significant when compared with the similar northwest trend of the Central Kansas Uplift, a major trend of production. 2) Considering the various northeast zones of Fig. 2, and with particular reference to Mayo&apos;s C-C, the Jemez Zone is on direct line with one of several northeast-southwest controls which the present writer has been using with some success in Kansas subsurface correlations. Considering zones of shearing, with no apparent vertical displacement, but suggesting strike-slip movement, because of the staggered effect on other features which cross such trends, Mayo&apos;s philosophy presents regional possibilities for lines of weakness, considered to this time of only local significance. 3) And, finally, in an area as distant from the Southwest as central Kansas, the north-south trends of the Fiarport-Ruggles anticline, the Voshel-Hol-low Nikkel-Burrton structures, the Dayton to Stut-gart trend, the north, slightly east trend of the Ne-maha structural complex, and others all seem to approach the north-south alignments, a through f, of Mayo&apos;s Fig. 3. Mayo&apos;s employment of structural intersections to pinpoint crustal weakness, to localize igneous activity and its accompanying mineralization is not, perhaps, a new concept, but it is a 1958 model, produced by tools improved from the ever-increasing accumulation of geological observations. The use of intersecting trends in petroleum geology is not a new idea, since much production in earlier days was encountered via the straight line projections of established trends to centers of intersection. A tragedy in this age of specialization is that iron curtains have been raised between groups, all seeking raw materials, all acolytes at the altar of structural geology, but all smugly content in and protected by the ivory towers of petroleum geology, engineering geology, mining geology, and geophysics. Mayo presents basic ideas which can stimulate mid-continent structural thinking and, in the case of cen- tral Kansas. he provides a key to replace the broad and overworked simple monoclinal, sinkhole-dotted, Karst topography credo, which is not finding its share of new oil in a state where the declining discovery ratio is disconcerting. The American Association of Petroleum Geologists would do well to add E. B. Mayo to its list of Distinguished Lecturers. Evans B. Mayo (author&apos;s reply)—In reply to David LeCount Evans&apos; comments, it is pleasing to learn that some of the elements discussed in my paper may interest petroleum geologists as well as mining geologists. This should not be surprising, however, because the lineaments make up the framework of the continent, and the oil-bearing sediments must reflect to varying degrees adjustments of basement blocks along their boundaries. A further possibility that petroleum geologists must have considered is that the slow escape of heat from buried lineaments and their intersections has aided the separation of oil from the sediments and started the migration into traps. Regarding the specific points listed by Evans, the following are suggested: 1) The branch of Texas Lineament marked 1&apos; (Fig. 3) is thought to extend eastward through the Capitan Mts., New Mexico, through the long Tertiary dikes east of Roswell, and beyond via the Matador and Electra ranges of the Red River Uplift, Texas. Its further continuation might be the eastern flank of the Ouachita Fold Belt. The Amarillo-Wichita-Arbuckle zone of uplifts appears to continue east-southeastward the Spanish Peaks belt (3-5, Fig. 3). The northwest-trending Central Kansas Uplift would not belong to the above set, except insofar as the Central Kansas Uplift is traversed by west-northwest folds, possible continuations of the Uinta belt (5-5, Fig. 3). 2) The possible continuations into Kansas of the Jemez zone are new to me and are most welcome suggestions. 3) Most of the nearly north-south Kansan structures mentioned by Evans are unfamiliar to me, but the Nemaha Uplift itself appears to be part of a very pronounced structure traceable from the Cerralvo Fault Zone, south of the Rio Grande, through the Bend Arch, Texas, and the Nemaha Uplift, into the Pre-Cambrian of Minnesota (?). This nearly meridional zone is crossed and broken by the Rio Grande Embayment and by the Red River-Wichita Syntaxis. Petroleum geologists realize the economic importance of these features. Perhaps it is inevitable that some papers of general interest be buried in the journals of specialized groups. Moreover, papers dealing with regional, or lineament, tectonics and its applications to exploration for economic mineral deposits are as yet few in the American literature. The opportunity to advance this field is open to all those who are not ultra-conservative and who have a lively curiosity, plenty of patience, and not too many business restrictions. In conclusion, much appreciation is extended to D. L. Evans for his comments.

Jan 1, 1960

By R. Hogg, S. Chander

"An overview of various physical and interfacial characterization methods for use in mineral processing is presented in this paper. The availability of a large number of characterization techniques and commercial instruments requires that the reliability and limitation of each be carefully examined. The choice of a method may depend upon the manner in which the information is to be used, for example in development of new processes, plant and process design, plant control, problem solving, etc. IntroductionThe behavior of particulate systems, in mineral processing and other applications, is primarily affected by the physical characteristics (size, shape, surface area, pore structure) of the particles and the nature of the different solid-fluid interfaces present. Mineral processing operations in general are either designed to modify and/or control physical and interfacial properties (grinding, classification, agglomeration, etc.) or are strongly influenced by them (flotation, flocculation, solid/liquid separation, etc.). Characterization of physical and interfacial properties should be an integral part of the development of new processes, plant and process design, and routine plant operation.Our purpose in preparing this article has been to present an overview of the current status of characterization, to point out areas of weakness, and to discuss the reliability and limitations of the various techniques, procedures, and instrumentation available. For more detailed discussion of methods, etc., the reader is referred to standard references.Sampling particulate solids.Sampling is a critical factor in any procedure for characterizing particulate materials — the reliability of characterization data is ultimately limited by the extent to which the sample used was truly represen¬tative of the population from which it was taken.Sampling from particulate solids involves two basic problems: (1) the selection of a random', unbiased sample and (2) choice of the appropriate sample size.The problem of sample selection involves the design of a sample collection procedure that ensures that every kind of particle in the population has the proper chance of being included in the sample without bias. Specific procedures such as the well-known cone-and-quarter technique have been developed and are discussed at length in the literature on particle characterization (Allen, 1981: Herdan, 1960: Gy, 1982)."

Jan 1, 1989

By R. Webeler

In order to study the role of work hardening in the fatigue process, use was made of the great sensitivty of the resistivity of AuCu to cold work. A change of the resistivity of AuCu of the order of 1 to 2 pct at the temperature of liquid nitrogen was found to occur as a consequence of severe fatigue. ACCORDING to Orowan&apos;s theory,&apos; the process of fatigue In metals 1s associated with the production of a number of small regions which have undergone strain hardening. This phenomenon is supposed to occilr even if the stress applied during fatiguing is always smaller than the yield stress. In an attempt to verity the existence of such regions, Welber and Webeler&apos; undertook to detect the stored energy associated with severe fatigue in copper. Previous experiments" had shown that the energy stored in a sample of copper which has been cold worked by torsion is released in the temperature range between 150" and 250°C when the sample is heated from room temperature and that no more energy is released (or absorbed) between 250" and 450°C. In particular the stored energy amounted to 0.41 cal per g for a case in which the mechanical energy expended in twisting the sample was 11.9 cal per g. In the case of fatigued copper, however, no release of stored energy could be detected between 150" and 250°C, so that the experimental error of &0.02 cal per g represents an upper limit for the amount of energy stored in strain hardening., It seemed desirable to attack the problem in a new fashion. For this purpose, it was decided to make use of the fact that, if an alloy capable of undergoing the order-disorder transition is ordered and then cold worked, the resistivity, p, increases very greatly above the value for the ordered state even if the deformation is very small. Some insight into the nature of the fatigue process may be obtained then by measuring the resistivity of an ordered sample before and after subjecting it to fatigue. For reasons which will become apparent from the following remarks, considerably more can be learned by carrying out the resistivity measurements at two different temperatures. In the case of a material containing impurities, vacancies, dislocations, or other imperfections of essentially atomic dimensions, the resistivity, p, according to Matthiessen&apos;s rule, can be represented as a sum of two terms p = p, + p, where p, is the (temperature dependent) resistivity of the pure metal, and p, is the temperature independent contribution of the imperfections. Briefly, the physical basis for this rule is the following: The main contribution of the impurities in question to the resistivity results from the fact that they interrupt the periodicity of the lattice and thus scatter the conduction electrons with a probability which is almost independent of temperature. In order that this be the case, it is necessary that the&apos; extension of the impurities be small enough—roughly less than one electron mean free path—so that their main effect on the resistivity occurs for the foregoing reason. If an alloy like AuCu is partly or completely disordered by quenching from an appropriate temperature, Matthiessen&apos;s rule also applies to a very good approximation* with p, representing in this case the resistivity po of the ordered sample and p, the additional (temperature independent) resistivity due to the disorder. In general, the disorder can be represented in terms of atoms which are displaced from their "proper" positions in the superlattice and which thus qualitatively represent the imperfections in the superlattice responsible for the term p,. Since the misplaced atoms are distributed at random throughout the super-lattice, their contribution to the resistivity still can be considered in terms of the scattering of conduction electrons by lattice defects. The situation is somewhat more complex in the case of an alloy disordered by cold work because the process of disordering here does not involve a random redistribution of the atoms; however, Matthiessen&apos;s rule also holds in this case. Whenever Matthiessen&apos;s rule does apply, the values of the quantity /3 = (p? — /(T, — T,), where p, and p, are the values of the resistivity at two fixed temperatures, T, and T,, respectively, is constant (independent of p,) for a given alloy or metal. In particular, if a sample of AuCu is subjected to ordinary cold work, the value of /3 remains equal to Po, the value for the ordered material. According to Orowan&apos;s theory,&apos; as remarked before, a fatigued sample contains a large number of isolated severely cold-worked regions, which make up only a small proportion of the metal. Thus, if a sample of AuCu initially in the ordered state is fatigued, more or less disordered regions will be produced within the ordered material. If these regions are small enough so that Matthiessen&apos;s rule applies, then it follows from the previous discussion that /3 again will remain equal to Po. If the effect of fatigue is to produce cold-worked regions which are macroscopic—of the order of at least several electron mean free paths—the effective resistivity, p, has to be computed by use of the ordinary laws of large-scale electrodynamics. For the sake of simplicity, it will be assumed here that the cold-worked regions are completely disordered and have a resistivity, p,. For a given proportion A of disordered regions the effective resistivity, p, for the current in a given direction depends on the geometrical configuration of these regions. In any case, the value of p for such

Jan 1, 1956

By F. N. Rhines, B. H. Alexander

MUCH attention has been directed to the effects of grain size upon the properties of alloys, but there has been scant study either of the conditions that determine the pattern and dimensions of den-drites in metal systems, or of the influence of their shape and size upon the overall properties of cast-ings. The aim of the research that is about to be described has been to investigate the effect of vari-ous factors upon the mode of formation of dendrites in alloys by measurements of the distance between adjacent dendrite arms (dendrite spacing). Early investigators, including Grignonl and Tschernoff,2 showed that a metal dendrite is com-posed of a tree-like system of stalks and branches arranged in a simple geometrical pattern. North-cott and Thomas3 demonstrated that, in the face-centered cubic solid solutions of copper-base, these stalks and side arms all lie in (100) directions in the crystal. Several investigators, including Sauveur and Chou,0 Sauveur and Reed,&apos; and Martin and Mar-tina have reported that the addition to steel of alloy-ing elements, such as nickel, chromium, and molybdenum, not only makes the dendrites easier to reveal by etching, but makes them coarser. The latter authors8 proposed that the coarsening of the dendrites is roughly proportional to the increase in the temperature range of freezing, caused by adding the alloying elements. Sauveur and Chou6 showed, in addition, that the dendrites are coarsened by a decreased rate of cooling of the casting. Measurement of Dendrite Arm Spacing Among the physical conditions that could be ex-pected to have an influence upon the dendrite arm spacing, that appears in a cast metal, are: composi-tion, rate of freezing, crystal structure, and type of constitution. The relationships obtaining between these variables and the dendrite dimensions have been examined, in the present research, by measur- ing the arm spacing in a wide variety of alloys, listed in tables II through VI. Alloy compositions are recorded in the tables by showing the symbol of the major metal followed by the percentage and symbol of the alloying agent; thus, "Al-10Ag" is an aluminum-base alloy containing 10 pct of silver. Although none of the alloys were analyzed, an im-pression of their degree of purity may be obtained from that of their component metals given in table I. Five hundred grams of each alloy was made by melting in small clay-graphite crucibles in an elec-tric muffle furnace. After alloying the temperature was adjusted to 50" to 75°C above the liquidus and the melts were poured into cast iron molds, at room temperature, the molds having a wall thickness of 1 in. and a cavity 11/2 in. sq in cross-section. Each ingot, thus cast, was sectioned at mid-height and the sectioned surface was polished and etched for metallographic examination. Dendrite spacing meas-urements were made at three positions, namely, ad-jacent to the mold wall, midway between the wall and the center of the ingot, and at the center (desig-nated e, m, and c respectively, in the tables). A typical series of microstructures is presented in fig. 1. For each measurement, the average was taken of the dendrite spacing of several grains covering a zone about 2 mm wide. Only those grains which had a major dendrite axis nearly in the plane of polish were selected in order to eliminate corrections for orientation differences from grain to grain. Although the dendrite spacings were measured to the nearest thousandth of a millimeter, the values listed in the tables are thought to be significant only to the nearest hundredth of a millimeter. The larg-est difference in readings found, when various ob-servers rated the same specimens, was 0.012 mm; the largest difference between corresponding meas-urements upon duplicate specimens was 0.027 mm.

Jan 1, 1951

By Thomas P. Holden, Todd M. Ruff

Problem: An average of three workers a year are killed in surface mining operations when a piece of haulage equipment collides with another smaller vehicle or a worker on foot. Another three workers are killed each year when haulage equipment backs over the edge of a dump point or stockpile. Devices to monitor the blind areas of mining equipment are needed to provide a warning to operators when a vehicle, person, or change in terrain is near the equipment. Method: A proximity warning system (PWS) based on the global positioning system (GPS) and peer-to-peer communication has been developed to prevent collisions between mining equipment, small vehicles, and stationary structures. Results: A final system was demonstrated using one off-highway haul truck, three smaller vehicles, and various stationary structures at a surface mining operation. The system successfully displayed the location of nearby vehicles and stationary structures and provided visual and audible warnings to the equipment operator when they were within a preset distance. Summary: Many surface mining operations already use GPS technology on their mobile equipment for tracking and dispatch. Our tests have shown that it is feasible to add proximity warning to these existing systems as a safety feature. Larger scale and long-term tests are needed to prove the technology adequately. Impact on Industry: A PWSs that incorporates a combination of technologies could significantly reduce accidents that involve collisions or driving over an edge at surface mining operations.

During the hydrometallurgical processing of the major base metals Cu, Zn, Ni and Co, the presence of iron is normally a serious complication, and iron separation from the pay metals usually constitutes one of the main challenges for the metallurgist. There are many instances, however, where the presence of iron is beneficial, or is even required. Two cases are presented where iron is required during the processing of base metals. The first example deals with the use of ferric sulphate to oxidize sulphides, more particularly copper and zinc sulphides, under atmospheric conditions. The results presented confirm that ferric ion leaching is efficient, particularly when the oxidant is regenerated during the process. The second case is the use of iron to solubilise refractory cobalt oxide minerals; examples, including pilot plant results, are presented for various ores from Africa and Central America. In both cases, this paper reviews the basic concepts involved and provides details of their application.

Jan 1, 2006

By A. B. Hooker

[Permissible electric cap lamps represent a workable balance between the amount of light needed and the various limiting conditions, such as the weight the miner can carry conveniently, cost of the lamp, including upkeep, and adequacy or practicability of the lamp as regards safety, mechanical strength, and general performance. Other things being equal, the coot desirable lamp is one that gives the greatest amount of useful light. Conversely, with a given amount of light the most desirable lamp is one that its the most efficient respecting weight, cost, and performance.]

Jan 1, 1935

By Enrui Dai, Weibing Chen, Bin Yang, Wenhui Ma, Haisheng Fang, Hui Wang

LiMn0.8Fe0.2PO4/C composite was prepared by an improved solid-state method and the effect of calcination temperature on properties of the obtained materials was investigated. The results showed that increasing calcination temperature from 600 to 700 oC improved the performance of the LiMn0.8Fe0.2PO4/C due to enhanced crystallinity and increased conductivity, but further increase in calcination temperature to 800 oC led to degraded performance due to particle growth and decrease in porosity. Therefore, the LiMn0.8Fe0.2PO4/C composite prepared at 700 oC exhibited the best electrochemical performance, and could deliver a high capacity of 152 mAh g−1 at 0.1 C, 147 mAh g−1 at 1 C and 114 mAh g−1 at 10 C. In addition, the performance of the LiMn0.8Fe0.2PO4/C and LiMn0.8Fe0.19Mg0.01PO4/C was compared when they were obtained at the optimum calcination temperature.

Jan 1, 2015

Introduction The US mineral industry in 1983 participated in the recovery from the recent recession. Compared with 1982, the value of raw nonfuel mineral output rose 8% to $21.2 billion. The $218 billion worth of goods processed from this crude mineral output represented a 9% increase over 1982. Even in real terms, these figures reflect growth. Demand for nonfuel mineral materials, of course, depends on the overall state of the economy, which steadily improved each quarter in 1983. Of particular importance to the mineral industry were surges in key mineral-consuming sectors such as construction and automobile manufacturing. New housing starts rose one-third, to 1.7 million units, while automakers turned out about 35% more cars (6.8 million) and 25% more trucks (2.4 million) than in 1982. These are significant increases, even considering recent trends toward smaller, lighter vehicles, and multiple-unit housing. A comeback for the mineral industry, however, is bound to proceed unevenly, particularly at the beginning. Traditionally, the industry lags behind the rest of the economy during a recovery, and some mineral products respond to overall economic improvement more quickly than others. This pattern has been repeated many times and the industry is used to it. Mineral executives know it is best to be patient and cautious during the first stages of an economic upturn. Many experts say that it may take extraordinary toughness, patience, and caution this time around. Steel Improves Raw steel production - a major indicator of both material use and mineral production - rose 14% to 77 Mt (85 million st), stimulating a 7% rise in domestic iron ore production to 39 Mt (38 million It). Still, the iron ore industry operated at less than half capacity, with most major mines remaining closed for part of the year. Iron ore imports dropped 24% to 10 Mt (11 million st), so demand was partly met by withdrawals from stocks. Despite the increase in steel production for 1983, output remained far below levels of just a few years ago. For example, 1983 production was still 29% less than in 1981. Raw steelmaking capacity actually declined about 10% during the year to 122 Mt (135 million st). The industry continued to cite steel imports, especially those from developing nations, as a major cause of domestic capacity loss. As long as steel production remains weak, steelmaking metals suffer. Domestic producers of bulk ferroalloys of chromium, manganese, and silicon operated at about one-third capacity in 1983, with six of the 19 companies involved being closed all year. The US mined no manganese or chromium, and very little nickel, although the country&apos;s only nickel mine did resume production in November. Molybdenum production, at 13.6 t (15 st), was only about one-third as much as in 1982. The major molybdenum mines, Climax and Henderson in Colorado, remained closed all year. To meet demand, molybdenum stocks were halved to 19 t (21 st). Mine shipments of tungsten, another mineral tied to steel production, dropped 30% to 1.1 kt (1,200 st) of contained metal. One of the most positive responses to the general economic recovery came from the aluminum smelting industry. By the end of the year, it was operating at about 79% capacity, compared to 59% in January. Nevertheless, the 3.3 Mt (3.64 million st) of primary aluminum produced represented only a slight increase over 1982. Total bauxite imports were about 27% below 1982 levels. Production of magnesium metal rose 11% to 100 kt (110,000 st). But titanium was more typical of other

Jan 5, 1984