Search Documents

By Porter W. Shimer

The device here described has been found useful in sampling foundry-iron, and there is no reason why it should not be equally useful in sampling other metals, which are not too hard to be drilled with a breast-drill. It consists, as shown in Figs. 1 and 2, of an ordinary plumber's gas T (without bead) of about 1/2-inch in internal diameter, over the leg of which is snugly fitted a small tin cup, about If inches deep, to catch the drillings which are made by use of a breast-drill with a 1/4-inch twist bit, working through the arms of the T. The forward arm of the T is filed down to a blunt edge, over which is stretched a short piece of rubber tubing projecting a little beyond the end. The bottom of the inside of the front arm of the ? is filed down to a slope, to facilitate the passage of drillings into the tin cup. The rear arm of the T is fitted with a tin ring, projecting about 1/4-inch, for the purpose of holding in place a stiff spiral brass spring, which serves to press the sampler firmly against the metal to be drilled. The other end of the spring is supported against a shoulder of the breastdrill. The projecting rubber prevents the loss of any drillings, and also the falling of sand from above into the sampler. With ordinary care there need be no risk of getting particles of rubber into the sample. It is, of course, not possible to get a fair average sample of drillings, representing a pile of foundry-iron, by taking drillings from any one or two pieces, because of the frequently mixed character of the iron. This observation applies more particularly to the sampling of iron as it is broken and piled at the foundry, than to sampling at the works, where, if the furnace is working regularly, a few pigs may fairly represent a whole cast. By the use of this device, it is possible for a sampler to pass

Jan 1, 1901

By Emmanuel V. Manlapig

The variables involved in a complex process like flotation can be classified as follows: a. Disturbance variables - which are undesired properties of the process input which affect the value of the process output but which are not subject to adjustment. They are the result of changes in the properties of the feed, like changes in head grade, flow rate, fineness of grind, etc. b. Manipulated variables (sometimes referred to as process variables or control variables) -which are those that are adjusted - reagent addition, aeration, pulp level - in order to compensate for the disturbances in the properties of feed. c. Performance variables (sometimes referred to as controlled variables) -which are those whose values measure the performance of the process. They are properties of the process output such as grade and recovery. The function of a control system is to maintain the process performance equal to the control objective in spite of the disturbances by adjusting the manipulated variables. Attempts at developing automatic control systems for mineral processing operations date back to the thirties and in many of these attempts the results were not surprisingly poor and un-stable. The poor results brought indifference and suspicion towards automatic control on the part of operators and management. The reasons for the apparent failure of these attempts were two-fold: a. the lack of adequate understanding of the behavioural responses of the process from the control point of view, and b. the lack of reliable control instrumentation which could withstand the harsh environment in mineral dressing plants. Many operators had accepted the fact that control of mineral dressing could be best conducted manually. In the case of flotation circuits, control had been virtually based on the skill and experience of operators particularly their ability to identify and rectify poor flotation performance aided by results from the laboratory (chemical) analysis of regularly collected samples from strategic points in the circuit which are at best, hourly collected samples.

Jan 1, 1978

This paper describes a steam outburst in a metal mine which occurred in December 1992 in Japan, resulting in two fatalities. The outburst occurred just after blasting in a heading face 600 m below surface (SL-50 m), 1664 m from a mouth of the mine. The scale of the outburst was large and the fragments of the outburst spread up to 34 m from the face, the total volume of the outburst was estimated to be 206 m3. The outburst materials were mostly clay originated from the typical surrounding rock of sulfide ore and basalt. The shape of the larger outburst fragments were slabs with a thickness of 10 to 20 cm. The victims were found in a main ventilation air shaft, 175 m and 380 m from the face, respectively. The mine mainly produces copper, lead and zinc. The face was ventilated by a 560 mm diameter duct with a fan and the strata temperature of the rock was estimated to be in the range of 120 to 140¦C. There is a famous hot spring near the mine. A thorough investigation into the unprecedented accident was made including an on-site inspection and investigation of rock characteristics in laboratories.

Jan 1, 2005

By J. S. Berber

Bastnasite is a natural fluocarbonate of the cerium group and affords an abundant and high-grade source of the lighter rare-earth elements. As part of a broad research program in rare-earth element technology, the Federal Bureau of Mines directed extensive experimental work to separating and purifying the rare-earth elements in bastnasite. By the use of a combination of techniques--classical chemical, ion exchange, and solvent extraction--the processing of a bastnasite concentrate to obtain the individual rare-earth elements, or groups of elements, was accomplished. A bastnasite concentrate, containing about 60 percent rare-earth oxides, was sulfated with concentrated sulfuric acid to eliminate the carbon dioxide, fluorine, and silica. Calcination at 1,200° F. made the gangue matter insoluble, thus permitting the separation of the soluble rare-earth sulfates. Essentially 100 percent of the rare-earth elements were recovered by this procedure. Since the rare-earth sulfate solution contained only trace amounts of nonrare-earth elements, subsequent separation procedures were simplified.

Jan 1, 1960

By T. W. West

INTRODUCTION This paper presents an assessment of conventional flotation technology. In addition it presents some ideas which can be used to change the perception of what may be done with conventional flotation equipment to maximize its efficiency. Perspective of Conventional Flotation Technology 1. Flotation in many coal preparation plants is defined as something between a necessary evil and a non-viable concept because: -Too much art is required on a continuous basis to achieve uniformly acceptable results. -It is expensive, the capital cost in dollars per ton of circuit feed for flotation and dewatering is high. -It is a difficult process to use when SO2 reduction governs system design and equipment selection. -It creates a product (fine coal froth) that is difficult to dewater in the presence of BTU/lb as-received pressures. -It is a difficult process to control from a management standpoint, there are no dependable set points to rely on. 2. Many froth cell circuits are 0.5m x 0 (nominal 28 M x 0) feed which is sourced from screen/cyclone underflows. The original intent was to obtain maximum yield at acceptable product quality and moisture using disc filters. (See Figure #1) 3. An alternate to conventional flotation and its perceived to be limits of efficiency, capital costs, etc. is to move towards such developing flotation technologies as column flotation, reverse flotation, and microbubbles. A lot of work is being done to move these concepts thru pilot stages into full scale, commercial plant operation. The majority of the coal producers and coal preparation plant designers view these concepts as being in the development/pilot plant stages. OBJECTIVES Based on the preceeding comments of the perspectives of the coal producers and plant designers, the options are limited. They can make do with what they have available to them in the way of industry standard equipment and practices or they can move forward with developing technology. I feel there is a third option: what can we really do today with what is available to us, without reinventing the wheel? APPROACH 1. When processing coal against ash and SO2 restrictions, the fine clean coal stream can be the best stream on the clean coal conveyor due to the release by size and the ability to create a high BTU/low sulfur (dry basis) product. 2. Targets: -Consistent raw coal size consist in the plant feed . -Do not put pyrites in the froth cells. -Adjust criteria defining good flotation away from yield towards maximum BTU recovery at minimum ash. -Limit the froth cell feed size consist to 0.15 mm x 0 (nominal 100M x 0). -Establish and maintain a correct, consistent percent solids in the froth cell feed. -Select flotation reagents with care. -Introduce reagents in the proper sequence.

Jan 1, 1988

Although haulage truck collisions account for only a small percentage of haulage accidents, the likelihood of severe injury, or even death is very high when such a collision does occur. Most rear-end collisions also result in considerable equipment damage, creating a need for expensive repairs. To improve collision protection, some southwestern surface mines have, for several years, been fabricating and using extended bumpers. In cooperation with these mines, the Bureau of Mines has worked to improve this technology by evaluating the structural requiremnts of extended bumpers. How Extended Bumpers Help The Bureau found that when one large rear-dump haulage truck collides with the rear of another an extended bumper protects the driver of the vehicle that is struck by dissipating the impact energy into the rear tires and pushing the whole vehicle forward. An extended bumper also prevents the box on the truck that is hit from penetrating the cab of the other truck-a typical and serious collision hazard. A further advantage derives from the wide design of the extended bumper which helps prevent damage to truck ladders, thereby minimizing any entry or exit problems. Extended bumpers also provide safe work platforms at the front of large haulage vehicles.

Jan 1, 1984

By Karl-Heinz Frohne

This report presents the findings of a study of a portion of the Clover-Rush Run oilfield located in Roane County, W. Va. The study was made to investigate the possibilities of secondary oil recovery in the Big Injun sandstone underlying the William Kaufman lease. Reservoir properties, original reserves, and primary oil recovery are also presented. The investigation is based on a core analysis and related laboratory tests, well records, field production data, and subsurface information from the Kaufman property. A theoretical primary oil recovery of 9.7 percent of original oil in place is predicted for the reservoir. A waterflood performance prediction of a hypothetical pilot area was made by use of a computer. The prediction showed that, based on laboratory oil water relative permeability curves, the water-injection time needed to initiate oil production is excessive and that the stabilized water-injection and corresponding oil-production rates are very low. This precludes waterflooding the reservoir on an economic basis. A prediction for secondary oil recovery by gas injection was attempted but could not be completed because essential reservoir data were not available. In July 1965, the lease operator initiated, and is currently conducting, a gas-injection program, but there had been no increase in oil production up to November 1966.

Jan 1, 1967

By Nicola Baldo, Marco Pasetto

"The paper discusses the results of a laboratory study, aimed to evaluate the suitability of the bottom ash from Municipal Solid Waste Incineration (MSWI), obtained from different Italian plants, to be recycled in the lithic skeleton of bituminous mixtures, for base layers of road and airport pavements. The research involved a preliminary study of the physical and geotechnical properties of the bottom ash by itself; it was followed by a mechanical characterization of the bituminous concretes. The traditional Marshall methodology was used to identify the optimum bitumen content; the mixtures were also mechanically checked by means of the stiffness modulus test, repeated load axial test and fatigue test. Because the requisites for acceptance in the Italian Specifications and Standards have been satisfied and given the positive mechanical performances, it has been verified that the MSWI bottom ash can be used as substitution of the lithic materials in the road bases, also with very high contents (up to 81% on the weight of the aggregate). Introduction The incineration of Municipal Solid Wastes (MSWs) provides for by-products which can be mainly classified as bottom ash and fly ash. The first one, corresponding to the 25% on the weight of the wastes to be incinerated, so resulting the principal product of the process, is mainly composed by Silica (Si), Iron (Fe), Calcium (Ca), Aluminium (Al), Sodium (Na) and Potassium (K) oxides, so presenting a composition similar to that of different natural materials. Its metallic fraction can be recovered; the remaining part is usually stocked in dumping or, less frequently, recycled. Bottom ash can be re-utilised in the construction of new infrastructures, especially in bitumen bounded mixtures, because of the inert properties of the binder which covers the grains with a subtle film, that prevents the release of heavy metals. The paper describes a study aimed to design new bituminous mixes for flexible road and airport pavements, realised with the highest content of 4 types of bottom ashes, deriving from different MSWI plants of the Northern Italy. The ashes will be named as BA1, BA2, BA3, BA4 respectively (the origin cannot be specified)."

Jan 1, 2008

By James C. Church

The Bureau of Mines devised and demonstrated a portable linear cutting tester that directly measures and records the in situ cutting forces required of continuous-mining machine picks to it coal in underground mines. It requires only two operators to transport and operate the tester, which can be assembled and operated through a complete test cycle within a single mine work shift. This report reviews the factors considered in the design and development of the tester and the results of its system verification testing at coal mine sites.

Jan 1, 1985

By W. L. Nelson

The orebodies at Copper Mounta1n lie along and within a few hundred feet of the contact of an intrusive stock of gabbro with a series of bedded volcanic rocks of the Nicola formation. These. orebodies are all entirely within the volcanic series but in many cases the centre line of the orebody at depth is directly under the gabbro contact at the surface, due to a slight overhang of the gabbro. The gabbro and volcanic rocks are cut by a number of faults and fault zones which did not materially affect early mining operations, but, as undeground openings increased in size, the faults became more important factors in determining mining methods and procedure. Caving methods were adopted to take advantage of ground weakness in fault zones, and the effect of ground subsidence which resulted from the division of the ground 1nto large, independent blocks by faulting had to be considered in planning the sequence of mining of certain ore blocks. The faults have been divided into two classes: the longitudinal system and the cross faults, or 'breaks' as they are termed locally. In addition to the two classes of faults, the zones of parallel ore fracture also control mining procedure, but to a lesser degree, in regard to caving or ground subsidence. A third structural feature which influences mining procedure is the mine dyke system. The longitudinal or main fault system roughly parallels the gab? bro contact and is made up of a number of branches and auxiliary fractures. The main fault itself is essentially vertical, but there are a number of branches and fractures on each side of it which, though parallel m strike, may dip as flat as 50 degrees toward or away from the main fault. The full width of the main fault system has not been determined, but it is known to extend beyond the zone of mine workings. A marked schistosity follows the main fault and both schistosity and chloritic alteration have been noticed along the secondary faults of this system. Several prominent orebodies lie along the main fault and its branches. The influence of the main fault system on mining is probably related more to subsidence than to actual cavi.ng, although it is effective in both.

Jan 1, 1950

By W. H. Blackburn

This paper describing the milling practice at the Tybo concentrator is one of a series of similar papers being prepared by the United States Bureau of Mines on milling methods and costs at the various mills in the United States. ACKNOWLEDGMENT A large part of this paper way prepared by H. M. Lewers, mill superintendent of the Tybo plant of the Treadwell Yukon Co., Ltd.

Jan 1, 1931

By Marcos Danilo Monteiro

O final do século XX foi marcado por um grande avanço tecnológico em sistemas automatizados com variadas aplicações, dando destaque ao campo da robótica que desde então busca otimizar cada vez mais os processos industriais, eliminado a mão-de-obra humana em segmentos onde sua presença antes era indispensável. O aumento na qualidade do produto, a relação custo-benefício e dentre outras melhorias que a robótica trouxe a uma linha de produção industrial, justificam a procura por parte das grandes empresas em procurar investir na inserção desta tecnologia ou no melhoramento dela em sua cadeia produtiva. Este trabalho teve como principal objetivo demonstrar a aplicação da tecnologia robótica na indústria, em proporções reduzidas e fins didáticos, com a integração de um sistema de controle e automação representado pela plataforma Arduino que atua no controle de coordenadas de um braço robótico em atividades de carregamento e paletização de cargas.

Jul 30, 2018

By W. D. Dietzman

This Bureau of Mines report presents a profitability analysis of producing crude oil by waterflooding. Included are the estimated costs of installation of water injection and producing equipment for waterfloods at 2,000 and 4,000 feet and the estimated annual operational expenses for each in west Texas. Using these cost estimates as a base for selecting a range of costs that are indicative of producing crude oil by waterflooding, a simulation technique was derived for determining the profitability under various conditions. Because of the large number of combinations of variables used in this study, a high-speed digital computer was utilized for the calculations. The variables include operational expenses, capitalized costs, price of the oil, annual production, and leasehold acquisition cost. The results obtained from the simulations are presented Fn the appendix. In addition, a nomographical approach was chosen for presentation of the profitability. Five nomographs are presented that can be used for fast estimation of the discounted cash flow (DCF) rate of return that might be expected from a prospective or active operation under various sets of assumed conditions.

Jan 1, 1974

By B. W. Madsen

As part of a program to maintain an adequate supply of minerals and metals to meet national economic and strategic needs, the Bureau of Mines conducted research to determine the diffusion coefficients for ferric ions in synthetic copper leach solutions. Determination of ferric ion diffusion coefficients in typical dump leach solutions is necessary for predicting leaching rates of copper from large-scale leaching operations and for optimizing concentrations of ferric iron in solutions to maximize leaching efficiency. Derivative chronopotentiometry, an electroanalytical technique, was used to determine ferric ion diffusion coefficients. The diffusion coefficient decreased dramatically with increasing concentration of iron in solution. An empirical model was used to relate the ferric ion diffusion coefficient to the total amount of sulfate in solution. Measuring the diffusion coefficient dependence on temperature yielded an activation energy of 5.5 kcal/mole of ferric ion. Activity coefficients of ferric ions as a function of concentration were calculated from diffusion coefficient data.

Jan 1, 1981

By Thomas Brunsing

The program was carried out to develop deep kerfing and core breaking techniques to be incorporated into the design of a field prototype hard rock mining machine. The field machine is designed to mine non-abrasive bedded deposits up to 20,000 psi in uniaxial compressive strength. The mining technique involves cutting approximately 2 ft deep parallel kerfs spaced 2 ft apart in either a horizontal or vertical direction and subsequently breaking out the cores so defined. The prototype machine is intended for demonstration of the technique in a quarry or equivalent field environment. The program was aimed at minimizing the required kerf width, obtaining reliable breaking within that kerf width and determining cutter blade requirements necessary to achieve a mining rate of 20 ft3/min. Full scale breaking experiments and 1/2 scale kerfing experiments were employed to evaluate the system. High strength concrete test specimens were used to simulate the rock being cut and broken. The test results indicate the kerf/break technique can achieve the desired mining rate by utilizing two 7 ft diam blades to cut 2 in. wide by 24 in. deep kerfs. A lateral load applied at the base of the kerf (base shear) was selected at the core breaking technique to be employed by the full-scale prototype machine.

Jan 1, 1983

By Charles W. Henderson

THE influence of mineral production on the development of the western United States has been profound. From 1848 to 1860, there was only gold production, the effect of silver began in 1860, and from then on both had a powerful influence. Lead production started in 1863, copper in 1863, and zinc in 1885, but was small until 1898. Gold alone was therefore the stimulus of the early settlement and exploration of the Western States.. But mineral deposits caused neither acquisition of territory nor determination of boundary lines. Arizona, California, Nevada, New Mexico, and parts of Utah, Wyoming, and Colorado were formally acquired from Mexico fourteen days after the actual date of the discovery (January 19, 1848)1.2 of gold at Sutters Mill, near the present town of Coloma, California (a discovery which, with the immediate new discoveries, aroused the world several months later) ; but the acquisition was by treaty (under negotiation for some time but signed February 2, 1848)3 in settlement of a war involving the boundaries of the grassy plains of Texas, an area at that time not known to contain any metals, and to date found to have but few metal deposits.4 The international boundary at 49º latitude for the far northwest states was determined by causes other than mineral deposits.

Jan 1, 1933

By Chin J. Chang

Powder metallurgy (P/M) technique is known for its capability of producing near-net-shape parts. Its specific characteristics have resulted in low cost and eliminated of many secondary machining. However, more and more P/M parts do require additional operations to fulfil their complex geometric features and surface roughness. Many of the machining factors that influence the machinability of cast and wrought steel parts, such as cutting speed, feedrate, coolant, tool geometry and shape, are also considered in the machining of P/M components. The special feature in P/M structure is the porosity that can decrease the machinability and shorten the tool life. Different variables have been considered in the machinability of P/M materials. Densities and the free machining additive manganese sulphide (MnS), are the two main factors of material composition, which dominate the P/M machining performance. Machining process is the main method that generates the desired working surface of machining components. This paper will discuss the metallurgical structure of the powder metallurgy components, their physical properties and possible issues when encountering machining operation. Turning operation has been tested in this investigation to show the relationship between the cutting speed, federate, cutting forces and chip formation. This investigation also discusses how the free machining additive, manganese sulphide, affects the P/M structure and machinability in order to understand how the metallurgical structure can affect the machining operation and, how to obtain the optimised surface results.

May 1, 2001

By R. L. Alexander

"Madawaska Mines Limited, incorporated in 1975 is the successor to Faraday Uranium Mines Limited. The history of the latter's mine development and corporate changes are outlined. This paper describes the geology of the Bancroft area and the rock types found in the mine, particularly the pegmatite which is the host rock for the uranium. The structure, mineralogy and distribution of the ore shoots are described with the method of grade control and mine development. The paper concludes with a summary of the production and mineral reserves.Location, Access, and PropertyMadawaska Mines Limited is located in Faraday Township, Hastings County, Ontario. The mine is in the N.T.S. quadrant 31 F/ 4, Bancroft sheet and near 46 degrees 01 minute latitude, 77 degrees 46 minutes longitude. The mine is one-half mile north of Highway 28, five miles (8 km) west of Bancroft, and is accessible by various highways from Toronto, Ottawa, Peterborough, and Belleville. (Fig. 1). A landing strip for small aircraft is located at the northwestern edge of Bancroft. Bancroft is a modern community with a population of 2,400. The company has the mineral rights to 2982 acres (1207 hectares) surrounding the mine workings and plant which are situated in the north parts of Lots 16 and 17, Concession XI, Faraday Township."

Jan 1, 1986

By E. W. Dean

A previous report of the Bureau of Mines* has supplied data for the physical and chemical properties of samples of crude petroleum produced in the eastern fields of the United States. It was issued as a preliminary chapter of a bulletin which is to cover the results of a survey of the entire country. The present report is a second preliminary chapter including figures that are available for the producing fields of the Rocky Mountain district. Work is being continued. with a series of samples from the States of Kansas and Oklahoma which will be described in a third preliminary chapter, to appear at a subsequent date. Acknowledgments. The obtaining of samples was rendered possible through the courtesy of representatives of a number of producing and refining companies operating in the Rocky Mountain district. The Bureau hereby acknowledges its appreciation of the hearty spirit of cooperation that was universally encountered.

Jan 1, 1921

On 26 August 1971, the Bureau of Mines, through the Spokane Mining Research Center at Spokane, Washington, approved initiation of the evaluation of oscillatory energy toward enhancing flow of polymer into shale. The effort was an outgrowth of work performed under Bureau of Mines Contract H0210055, "Feasibility Study of Surface Impregnation equipment for the Chemical Stabilization of Coal Mine Structures," wherein feasibility of the impregnation concept was expressed and the detailed design of a machine for impregnation of coal mine roofs with polymer (under static pressure head) accomplished. Under these efforts, the potential enhance¬ment of polymer uptake into the shale thru superposition of oscillatory energy on the static impregnation pressure was suggested. A proposal for investigation of this phenomena entitled "Feasibility Study of the Application of Oscillatory Energy as an Aid to Afford Chemical Stabilization" was presented to the Bureau whereupon a three month program for initiation of investigation was approved.

Jan 1, 1972