Search Documents

By Rose CW

Typical rehabilitation programmes for spoil piles and waste dumps in open cut coal mines involve the spreading of topsoil to assist vegetation growth. In the early years of rehabilitation before a protective vegetation cover has been established, this topsoil is susceptible to erosion during rainfall events. Since the long term success of rehabil- itation procedures is sensitive to adequate topsoil maintenance and since, on many mine sites, topsoil is a scarce resource, erosion losses of topsoil (particularly once fert- ilised) can severely restrict rehabilitation Measures.

Jan 1, 1983

By Jaiza Bernardo de Oliveira, Iasmim Ariane Silva, Pedro Henrique Medeiros Câmara

The process of manufacturing pig iron in the blast furnace industrial units has the consequence of the generation of slag, a waste that can be produced in high quantity and present damages to the environment, when not reused. In the composition of this tailings, it is sometimes possible to find the presence of metals harmful to nature, such as manganese, which has an important and widespread utility in the metal industries, but still, the slag ends up not being used as a potential source of this element. Knowing this, the slags were subjected to crushing and grading steps to separate the aliquots. These were applied in the tests of technological characterization of the material, from MEV, EDS, Soxhlet and analysis of liberation degree by digital microscope, finding data of several analyzes. Having said that, the objective of this paper is to demonstrate, through the characterization of the slag, that this material has in its composition metallic elements, focusing on manganese, that can be reused in order to avoid the generation of environmental liabilities harmful to the environment. The results show a manganese content with a degree of release greater than 80% in bands from 48 #, which were divided by density and thus allow the gravimetric separation of the material in question.

Oct 3, 2019

By Afonso Garcez de Azevedo

As primeiras argamassas utilizadas em construções pelo homem continham em sua composição, materiais argilosos. Porém, por ser um material com muitas cargas elétricas livres, as argilas reagem constantemente com a água, ocasionando grande variação linear que acaba causando fissuração nas argamassas feitas com esse material. Assim, para solucionar esse problema, passou-se a utilizar cal hidratada no lugar dos materiais argilosos. Dessa maneira, mesmo não sendo composta por argila, a argamassa mantém sua trabalhabilidade. Nesse cenário, o presente trabalho teve como objetivo balancear estequiometricamente a cal hidratada e as argilas estudadas, para utilizar essas quantidades em argamassas para revestimento, barateando assim o material. Para encontrar esse balanceamento estequiométrico calculou-se a massa molar para um mol de cal hidratada e para um mol teórico de argila. Assim foram estipuladas algumas proporções possíveis de balanceamento da equação de reação cal+argila. Além disso, foram confeccionados corpos de prova, variando as quantidades de argila e cal, para realização de ensaios de capilaridade, a fim de comprovar a eficácia dos resultados encontrados no balanceamento teórico.

Oct 30, 2017

By Kymberley Worrell

The Cripple Creek and Victor Gold Mine was acquired by Newmont in August 2015. The high grade flotation mill project was commissioned in February 2014. The mill to date has been throughput limited due to mechanical and design issues. In order to create the most value from a throughput limited plant a campaign to provide timely ore characterization was undertaken. A diagnostic leach methodology was developed to determine gold associations by ore type. The resulting associations were then used to characterize feed blend; gold losses and optimize gold production. The diagnostic methodology is presented along with discussion on flotation implications.

By Helênio Resende Silva Junior

Em coquerias, o período compreendido entre o início de operação até a desativação devido final de vida útil é relativamente longo. Torna-se tarefa muito difícil determinar-se o tempo exato de desativação por degradação uma vez que as coquerias possuem muitos fornos tipo batelada e o grau individual de degradação varia de acordo com as condições operacionais e método de preservação aplicados. Apesar dos cuidados adotados na operação e manutenção das coquerias, torna-se inevitável um desgaste inexorável em suas estruturas com o passar dos anos, com progressivo decréscimo na capacidade eficaz de produção até a sua paralisação. Tendo em vista o elevado custo envolvido na construção de novas coquerias, torna-se prioridade para as siderúrgicas prolongarem ao máximo a vida útil das baterias existentes, adotando o tipo de reparo adequado a cada fase da vida da bateria. O presente trabalho tem o objetivo de descrever os tipos de reparo em baterias de coque disponíveis, visando restaurar as estruturas e recuperar a capacidade produtiva das coquerias, respeitando as normas ambientais vigentes.

Aug 16, 2017

By João Alberto Fioresi Altoé

Nas indústrias petroquímicas, nucleares e farmacêuticas o avanço tecnológico tem como objetivo a segurança e confiabilidade dos equipamentos com relação à resistência mecânica e à corrosão. Atualmente, o uso dos aços inoxidáveis superausteniticos é uma solução interessante, para uma maior vida útil dos componentes industriais submetidos a ambientes agressivos, como em meios salinos. Esse trabalho tem como objetivo investigar o aparecimento de pites em um aço comercial superaustenitico de composição química aproximada 25Cr28Ni4Mo em solução salina de cloreto de sódio. O aço foi fundido e tratado termicamente por solubilização a 1050ºC por 1h com o objetivo de eliminar os precipitados. As análises microestruturais antes e após os ensaios de corrosão foram feitas por microscopia óptica e eletrônica de varredura. Observou-se com os ensaios eletroquímicos de Polarização linear e impedância, que o aço inoxidável superaustenítico apresenta excelente resistência à corrosão em meio salino, caracterizado também pelas imagens que não revelaram a formação de pites, mesmo quando submetidos a elevados potenciais.

Aug 16, 2017

By RENARDIR PEIXOTO MACIEL JUNIOR

A importância do desenvolvimento sustentável, tendo como base um ambiente saudável para as gerações futuras, leva a se pensar em como as organizações poderiam desenvolver materiais menos danosos ao ambiente com boas propriedades e pelo menor custo. A proposta de aproveitamento de fibras vegetais para utilização em desenvolvimento de compósitos de matriz polimérica reforçados pelas mesmas é a motivação da pesquisa visando obter um compósito com melhores propriedades mecânicas e químicas do que sua matéria prima. Por virtude da importância do desenvolvimento desses materiais, a caracterização mecânica da fibra, da matriz e, finalmente, do compósito através de ensaios destrutivos e não destrutivos é fundamental para estudo de sua aplicação. Após a obtenção dos dados, percebeu-se que a adição das fibras melhorou as propriedades mecânicas do compósito resultante. Mostrando, portanto, resultados promissores para o desenvolvimento desses materiais, promovendo assim um material mais barato e de melhor propriedade mecânica, além de uma alta leveza. Em suma, os resultados estão de acordo com o esperado, impulsionando assim um melhor estudo desses materiais, por exemplo, realizando outros ensaios, como ensaios de impacto.

Oct 30, 2017

By Walter Kawa

Coals of various rank were reacted by the Bureau of Nines in plasma jets generated from argon and argon-hydrogen mixtures containing up to 33 volume-percent hydrogen. Average plasma temperatures ranged from about 3,400° to 12,000° C. Products were a solid residue and a gas containing hydrogen, methane, acetylene, diacetylene, and oxides of carbon. The highest yield of acetylene obtained with argon plasmas was 15 percent by weight of moisture- and ash-free coal. The data indicated that acetylene yields of 40 percent or higher can be obtained from the reaction of coal in argon-hydrogen plasmas, although results from these experiments could not be correlated with operating variables because of low recoveries plasma contained sufficient energy to heat the coal to temperatures as high 9,000 or 10,000° C, but complete devolatilization did not occur in any experiment.

Jan 1, 1966

By I. Vazaios, M. S. Diederichs, N. Vlachopoulos

"As rock engineering moves from continuum to more discontinuum approaches for modeling, the engineer must make decisions regarding the degree of complexity to simulate for a given application, balancing the level of structural detail within the rockmass model with computational cost and result accuracy. It is important to consider that model does not need to include all the existent fractures and that representative geometrical properties for a given rock mass volume can be defined including only major structural entities.Within this paper, the scale-dependency associated with the geometrical properties of fractured rock is investigated utilizing a Synthetic Rockmass (SRM) approach with a view to characterize such ground to aid in the design of geotechnical works. In terms of process, the concept of the Representative Elementary Volume (REV) is used to determine the equivalent structural properties of the rockmass in order to justify the applicability of far-field behaviour of such ground. A large size Discrete Fracture Network (DFN) measuring 60m x 60m x 60m has been generated using the structural data obtained from LiDAR scanning of the Brockville Tunnel, Ontario, Canada. A number of DFN samples of varying sizes are extracted from the master network, generated using MoFrac, in order to be used as a the basis of the structural analysis of the rockmass. Volumetric measurements for the density and the intensity of jointing are employed in order to approximate the geometrical REV for the networks.In this paper a complete methodology of how to generate a DFN from LiDAR data and its analysis in order to determine the size of a geometrical REV is demonstrated. For the specific rockmass found in the area of the Brockville Tunnel, a geometrical REV measuring 3.5m x 3.5m x 7m is established. The results are generally in good agreement with the in-situ observations."

Jan 1, 2015

By Ben M. Lewis, Yogesh Prashar

"The East Bay Municipal Utility District (EBMUD) is a major water utility service providing water to over 1.3 million people in the eastern San Francisco Bay Area. EBMUD manages 28 dams at 5 terminal and 23 open-cut reservoirs within a 331-square-mile customer service area. As part of a 2012 update on EBMUD’s Infrastructure Rehabilitation Plan for Distribution Reservoirs, EBMUD has decided to replace Central Reservoir, a 152.8 milliongallon open cut reservoir, with optimally sized tanks. This paper presents the results of an analytical comparison of various foundation reinforcement solutions for the proposed tanks including: Cement Deep Soil Mixed (CDSM) columns, vibro stone columns, rammed aggregate piers, and lightweight cellular concrete fill. The computational program GeoMat (www.ensoftinc.com) was used to perform simplified soil structure interaction analyses. Settlement estimates were developed for each alternative with the proposed loading and compared to an allowable differential settlement criterion established at 0.3-inches over a 50 foot length. The authors wish to present the importance of considering mat and soil interaction along with various settlement mitigation methods considered for this challenging project.INTRODUCTIONProject BackgroundCentral Reservoir is an operational open-cut reservoir located north of the intersection of 25th Avenue and East 29th Street in Oakland, California. The reservoir is bound by 23rd Avenue to the west, Sheffield Avenue to the east and Interstate Highway 580 to the north. Originally, the Central Reservoir site was a drainage swale incising into weathered bedrock formed from Pleistocene alluvial deposits. The reservoir was first constructed in 1910 by excavating a basin below grade and constructing an embankment dam on the south and cutting/filling the bedrock and alluvial deposits from the drainage swale. The main dam at the Central Reservoir site is also a DSOD (Department of Safety of Dams) jurisdictional dam and as such is regularly monitored by the EBMUD Materials Engineering Section and the California DSOD.In a 2012 update to EBMUD’s Infrastructure Rehabilitation Plan for Distribution Reservoirs, Central Reservoir was identified as a critical facility that has reached the end of its useful life and must be replaced due to: a failing panel craft lining which contains polychlorinated biphenyls in the interior coating, a roof that does not meet the current seismic code, and reduced operating levels due to potential leakage in the upper portions of the panel craft lining. Furthermore, Central Reservoir is about three times larger than required and is located at a lower elevation than other regional reservoirs in the pressure zone resulting in increased labor-intensive operational challenges and water quality operations.This project presents some challenging geotechnical demands – the site is founded on weakly consolidated Holocene Alluvium overlying weathered bedrock, the proposed structural loads are large, and the new Central Reservoir is to be placed on a pad at an elevation of 182 feet, required placement of up to 30 feet of fill over the current basin. Additionally, the project aims for a long-term foundation solution that will outlive the new replacement tanks and accommodate future site upgrades. In order to meet this goal, the differential settlement criterion for the tanks was ¼ inch over 50 feet length. Lastly, the project also aims to address EBMUD’s increasing trench spoil stockpiles by recycling discarded trench spoils as fill for the proposed tank pad."

Jan 1, 2016

By Amy McBrayer, Vladislav Kecojevic, Juan David Valencia Quiceno, Dragan Bogunovic

The mining industry’s commitment to innovation reflects a history of adopting technological advancements to enhance workplace safety, environmental sustainability and vocational training. The objective of this research was to develop an augmented- reality (AR) system for heavy-equipment operators (HEOs) in surface mining. The developed system has the potential to enhance mine safety, training and data-driven decision- making, which presents a significant step toward a more sustainable, effective and technologically driven mining training, contributing to the industry’s evolution and growth. The AR training system leverages Microsoft’s Power Platform and HoloLens 2 capacities to provide operators with detailed and immersive training guides for three mining equipment, including bulldozers, motor graders and haul trucks. AR guides combine speech controls, 3D objects, informative images and explicative videos in the real working conditions to enhance the operator’s learning process. The system has the potential to modify the training structure based on user performance and provides an efficient approach to data collection during training. This project was developed and applied through a case study in a surface mine in the Southern United States.

Feb 1, 2025

By J. P. Rider

The number of extended cut mining systems has increased significantly in coal mines over the last decade, and there is a constant push to extend the face ventilation systems to even greater setback distances. The need to maintain airflow at setback distances of12.2 m (40 ft) and beyond requires that methods for delivering intake air to the face be improved, or alternative ventilation techniques be implemented. The emphasis of this research effort was to examine various techniques to improve the distribution of available air at the mining face in order to reduce face methane levels. A study was conducted comparing the performance of a jet fan, used in conjunction with a machine mounted scrubber, with blowing curtain ventilation in a 27.5 m (90 ft) heading. In addition, a second study was performed on blowing curtain systems examining how scrubber flow, intake air velocity, and curtain setback influence face methane concentrations. Results showed that when the heading advances to a depth of 27.5 m (90 ft) blowing curtain systems were more efficient at diluting face methane levels when compared to a jet fan. Also, increases in scrubber flows and curtain velocity resulted in lower face methane concentrations for blowing curtain systems at 9.2 and 15.2 m (30 and 50 ft) setbacks.

Jan 1, 1997

By Gavin Erickson, Lucas R. Moore, Clint Stoddard, Garret Bryant

As global mineral feed grades decline, phosphate beneficiation faces mounting challenges. Chief among these being achieving high recoveries of industry quality concentrates from ores of decreasing quality. Apatite, a critical mineral for meeting global fertilizer demand, remains the primary source of phosphorus and is typically recovered through beneficiation by multi-stage flotation. However, traditional saponified fatty acid collectors lack the selectivity needed to beneficiate these lower quality ores, which are containing a higher concentration of more complex gangue minerals. Enhancing collector performance is essential to the industry moving forward. This study introduces a novel alkyl polyglucoside based surfactant designed as an additive for conventional fatty acid systems. Its incorporation significantly improves the grade recovery in direct apatite flotation, even at low concentrations. Flotation results as well as surfactant properties will be discussed.

Feb 22, 2026

MINING METHODS W. J. COULTER, Chairman P. B. BUCKY, Vice-Chairman CLYDE E. WEED, Vice-Chairman ROBERT S. PALMER, Secretary Alluvial Mining CLINTON BERNARD O. B. FERRY NORMAN CLEAVELAND C. M. ROMANOWITZ R. B. EARLING J. B. STAPLER BENERE H. GRANTCHARLES THURMAN

Jan 1, 1944

By Frank Firmstone

When in charge of the Glen don Iron Works, the importance of good methods of filling was forcibly brought to my attention, and it occurred to me that the first step toward the discovery of the best plans was the accumulation of exact information as to the distribution actually effected by various chargers; also, that something could be done in this direction by careful measurements in the furnace, to be afterwards recorded for comparison on drawings. The figures shown herewith have been prepared from such measurements, and nearly all of them refer to Glendon, where the fuel used was anthracite and the ore-mixture about threequarters of New Jersey magnetic ores and one-quarter of brown-ores from the vicinity of the works. Every occasion furnished by the blowing-in of furnaces was utilized, but the data accumulated rather slowly in this way; and, opportunity oEering to make special trials at no great expense, the figures from 2 to 7 were thus obtained. The trials were made by dumping a hopperful (6 barrows) of material at once into the furnace, and, when all the fuel of a round (12 barrows) had been put in, the profile of the upper surface was obtained by stretching a steel tape across the top on a diameter and at a known height. By measuring down from this with a graduated rod, the profile was easily obtained with sufficient accuracy, especial pains being taken to get correctly the crests of the ridges and the bottoms of the hollows, as many intermediate points being included as seemed necessary. This was repeated on another diameter when there was occasion. The same course was followed for the limestone and ore.

Jan 1, 1899

By Baron Fidler, Dave Lilly, Matt Budin

Cumulative sum (CUSUM) statistical process control methods have been used in many industries to monitor quality control results. CUSUM charts are a method to determine when small changes in data indicate a major change in results. E.S. Page at AT&T developed the method in 1954. In many blasting situations, vibration and air blast readings vary slightly from blast to blast. Whether the change is significant or not can be hard to interpret from the raw data. CUSUM charts can assist in determining whether a major change is taking place and when the change began.

Jan 1, 2009

University of Alabama-University, Alabama, Mining and Metallurgical Society, William L Mason University of Alaska-College, Alaska, Mining Society of the University of Alaska, E H Beistline University of Arizona-Tucson, Arizona, Miners Society, S L Smith Birmingham-Southern College-Birmingham, Alabama, Pick and Hammer Club, Daniel D Arden University of California-Berkeley, California, Mineral Technology Association, Jack Washburn Carnegie Institute of Technology-Pittsburgh, Pennsylvania, The Metals Club, Gerhard Derge Case Institute of Technology-Cleveland, Ohio, Case Metallurgical Engineering Society, Robert F Hehemann City College of New York-New York, New York, CCNY Student Chapter AIME, Daniel T O'Connell

Jan 1, 1957

By Rodrigo Cruz Oliveira

Nos últimos anos, a indústria automotiva tem evoluído de forma significativa em relação à preservação ambiental e com respeito à segurança veicular. A Usiminas, alinhada a esses avanços, tem realizado estudos visando obter novos produtos de alta resistência mecânica que possibilitem a redução do peso dos veículos e diminuição do consumo de combustível, além do aumento da segurança. Para novos projetos de veículos, como fator de melhoria do desempenho dos materiais de alta resistência, têm assumido destaque especial nos aços Dual Phase, principalmente naqueles do grau 1000MPa, as características de expansão de furo, em função da correlação com a vida em fadiga e o comportamento à fratura. Esse trabalho teve por objetivo avaliar uma das etapas do ciclo de desenvolvimento de um aço Dual Phase do grau 1000MPa com características de expansão de furo maior que 20%. O trabalho avaliou três conceitos diferentes de liga submetidos a tratamentos térmicos específicos. Os resultados obtidos permitiram retroalimentar o ciclo posterior do desenvolvimento, no qual resultados positivos foram alcançados.

Aug 16, 2017

By Silvio de Carvalho Sabença

Um forno a arco elétrico é um tipo de forno industrial que usa uma corrente elétrica alternada para produzir calor. Estes equipamentos servem como uma alternativa para os altos fornos tradicionais, e desempenham um papel importante na produção de aço. Em um forno de arco elétrico, a corrente elétrica passa através dos eletrodos de grafite, do aço e de outros metais, o que resulta na produção de aço de modo mais rápido e eficiente. A queda de tensão no arco é, praticamente, proporcional à distância entre o eletrodo e a carga. O eletrodo corresponde ao polo positivo (+) e a carga o negativo (-). Em corrente alternada os pólos, positivo e negativo, trocam de posição a cada meio ciclo da tensão de rede. Sob condições de arco, forma-se, no eletrodo e na carga, uma finíssima camada altamente ionizada devida a uma altíssima concentração do campo elétrico nestas zonas. No forno o arco se extingue quando a corrente se anula e reacende, quando a tensão volta a crescer. Devido a constantes quebra de eletrodo foi montado o grupo de trabalho com objetivo de reduzir o consumo dos eletrodos, otimização do consumo de energia, redução do Power On, aumento da potência média e redução nas quebras de eletrodos. Esta implantação foi extremamente importante pois o mesmo está garantindo a continuidade operacional, de forma segura e confiável, de um dos equipamentos mais importantes para a produção de aço na Usina.

Aug 17, 2017

By Rodrigo Faveret Signorelli

O desenvolvimento das famílias de aço inoxidável ocorre ao longo do tempo de acordo com as necessidades apresentadas pelos usuários. As usinas siderúrgicas, em geral, coletam informações de mercado para entender quais produtos deverão ser lançados nos próximos anos antes de iniciar novos desenvolvimentos. Utilizando-se desta ferramenta, a Outokumpu abriu três frentes de pesquisa nos últimos anos em busca do desenvolvimento de novas ligas. A primeira linha de pesquisa trata de um aço ferrítico, denominado 4622, que possui alto teor de cromo, cuja resistência à corrosão é equivalente à resistência à corrosão do 304. A segunda linha de pesquisa contempla um aço austenítico que se assemelha ao 316L, denominado 316plus,porém com custo reduzido. Por último, a Outokumpu, ao notar que aços Duplex raramente eram aplicados em equipamentos e máquinas que dependiam de facilidade de conformação do material, iniciou o desenvolvimento da família FDX. Esta família é composta por aços inoxidáveis duplex com alongamento elevado, que os aproxima dos aços inoxidáveis austeníticos. O objetivo deste trabalho é apresentar estas três novidades recentemente lançadas pela Outokumpu ao mercado.

Jan 16, 2018