Search Documents

By H. A. Wahl

This paper presents methods of designing hydraulic fracture treatments in formations saturated with slightly compressible liquids. Howard and Fast describe the fluid-loss control resulting from the viscosity and compressibility effects of the reservoir fluid in terms of a fracturing fluid coefficient. However, for horizontal fractures, this coefficient is applicable to infinitely thick reservoirs. These methods of evaluating fluid loss from horizontal fractures during treatment differ from previous methods in that: (I) formation thickness is incorporated in the velocity function describing the rate of fluid loss to the formation; and (2) for a given thickness the relative position of the fracture to the horizontal boundaries of the reservoir or any interrnediate permeability barrier is incorporated in the design procedure. This theory is applied to several actual and hypothetical field cases. The results of these calculations demonstrate that the eflect of formation thickness on fluid loss from horizontal fractures may result in fractures several times larger than predicted by other methods. INTRODUCTION Hydraulic fracturing has been the dominating well-stimulation technique during the last decade. From the time it was commercially available, fracturing has had a very favorable success ratio compared to other stimulation methods. However, numerous wells that were successfully stimulated remained economic failures. Only in the last few years has the oil industry recognized the importance of designing treatments for each well which will yield the maximum profit. This implies that for a given set of treatment conditions the size and general physical characteristics of the fracture can be determined. One of the outstanding contributions in the field of fracture design was presented by Howard and Fast.' In their paper, three flow mechanisms that control fluid loss from the fracture to the formation are defined: (1) viscosity effects of the fracturing fluid, (2) viscosity and compressibility effects of the reservoir fluid, and (3) wall-building effects of a treated fracturing fluid. The rate of fluid loss to the formation adjacent to a fracture is shown to be a function of time. For each flow mechanism the velocity function v(t) is expressed as a constant or fracturing fluid coefficient divided by the square root of time. This form of v(t) can be used in the Carter equation, as developed in the Howard and Fasc paper, to estimate the areal extent of fractures. This equation may be written as In the following sections the effect of formation thickness on fluid loss from horizontal fractures is evaluated when the controlling flow mechanism is the viscosity and compressibility of the reservoir fluids. The major assumptions inherent in the Carter equation are brought out in subsequent mathematical developments. THE EFFECT OF RESERVOIR FLUIDS ON FRACTURE EXTENSION When a fracture treatment is performed using a fracturing fluid identical to the reservoir fluid, the only flow mechanism controlling fluid loss is the viscosity and compressibility effects of the reservoir fluids. In developing a fracturing fluid coefficient for this mechanism, Howard and Fast considered a segment of the formation bounded by a unit area on the fracture face and extending to infinity in the direction of leak-off as shown in Fig. 1(a). The direction of leak-off z is normal to the fracture face. The equation governing the linear isothermal flow of fluid into this segment is where a = Eq. 2 is a form of the diffusivity equation. It is derived from the equation of continuity, Darcy's law and Eq. 3

By E. E. Malouf

For centuries small amounts of copper have been recovered from acid mine-drainage waters. In recent years, the expansion of copper-bearing waste dump leaching for copper recovery has established a technological basis that is rapidly converting the art of copper leaching into a science. Copper leaching and recovery from solution has become an important adjunct of nearly all copper mining operations. Leaching of copper, whether from copper- bearing ore or waste, follows well established chemical reactions commonly in an acid circuit, but where leaching of copper is to be made in rock that is a high acid consumer, ammonia and ammonia carbonate, as well as cyanide leach solutions, can be used effectively. Current hydrometallurgical processes are being applied at an ever increasing rate to recover the trace amounts of copper in copper mine waste by in-place leaching. Currently approximately 300,000 tons of copper are produced annually in this manner while as recently as ten years ago, only one-eighth of this amount of precipitate copper was produced. Where copper occurs as an oxide in higher concentrations as to be classified as an ore rather than waste, then the hydrometallurgical processes are applied as percolation or agitation leaching in vats, pachuca tanks or prepared heaps. This approach gives better control over the recovery of the leach solutions, particularly in the processes where ammonia or cyanide leaching agents are to be used.

Jan 8, 1972

By R. B. Kaunda

One fundamental requirement for surface and underground rock engineering is the ability to characterise the rock mass. An accurate characterisation of the rock mass allows rock engineers to optimize designs safely and economically. A number of classification systems have been developed in the past 50 years to help characterise rock masses such as RMR, Q system, Rmi, and several others. The challenge in developing rock characterisation schemes is often practicality, i.e. creating systems with relatively simple inputs for the everyday practitioner. A second challenge is the degree of subjectivity often inherent in commonly used classification systems. These challenges are especially exacerbated in weak rock or densely jointed rock masses. This paper introduces a new approach to characterise densely jointed rock mass using artificial neural networks and principal component analysis, based on principles commonly used in the geotechnical engineering of rock fills and waste rock dumps. Thirteen input parameters are dimensionally compressed using principal component analysis. Using a global database with more than 100 case histories, an artificial neural network is developed to conduct the rock mass characterisation. The advantage of this approach is less subjectivity as commonly used engineering (quantitative) terms are put to use. A further advantage is that given that the method is site-data dependent, it allows for ‘fine tuning’ of the model for a specific site.

Jan 1, 2015

By A. J. Schindler, F-P Sawyer, T. Logan, M. L. Shutey-McCann, R. M. Perry

"Test work on biooxidation pretreatment of low-grade refractory gold ores has been ongoing at Newmont Gold Company since 1988, including laboratory testing and pilot biooxidation heaps (360 to 23,000 tonne). Metallurgical results of the biooxidation process utilizing Thiobacillus ferrooxidans (T. ferrooxiddans) have culminated in the design, construction, and operation of a biooxidation demonstration facility. The facility has processed 708,000 tonnes of refractory ore, using a batched process with separate pads for biooxidation and ammonium thiosulfate gold extraction. Siliceous sulfidic refractory (SSR) and carbonaceous sulfidic refractory (CSR) ores are treated separately during biooxidation pretreatment unit operation. Following biooxidation, the ores are neutralization with lime and placed on oxide leach pads or stacked on the ammonium thiosulfate leach pad. Gold is leached with either cyanide for SSR ores or ammonium thiosulfate for preg-robbing CSR ores.This paper will only address the biooxidation pretreatment process of the SSR and CSR ores.AcknowledgmentsThe authors appreciate the cooperation and approval of Newmont Gold Company Carlin Operations management for its support and permission to publish this paper. The paper draws on efforts and assistance of the following people and several others which are to many to list who participated over the past five years in bringing this project to its fruition: Dr. James A. Brierley, Chief Microbiologist, Newmont Metallurgical Services; Dr. Rong-Yu Wan, Metallurgical Manager, Newmont Metallurgical Services."

Jan 1, 1997

By Fathi Habashi

Poland has a unique copper industry. Copper sulphide concentrates are smelted in six shaft furnaces to produce matte and in a flash furnace directly to blister copper. Anodic slimes from electrorefining are treated by a modern technology to recover the precious metals. INTRODUCTION Poland's copper industry began in 1950 when the old and relatively small mines Lena and Konrad, located in Lower Silesia, were drained and recommenced production. In 1957 the industry entered a period of rapid development with the discovery of a rich ore body in the vicinity of Lubin and Polkowice which was the basis for the establishment, in 1961, of the Copper Mining and Smelting Combine (KGHM). In 1991 the Combine was restructured into a state-owned, joint-stock company under the new name of KGHM ?Polska Miedz? (KGHM ?Polish Copper?). It consists of three mines, three smelting and refining plants, and one rolling mill, and produces about 4% of the world?s copper and about 7% of the world?s silver.

May 1, 2001

By Aner W. Erickson

Magnetite iron deposits on Tolstoi Mountain were examined as part of the investigations by the Bureau of Mines of iron and copper ores on Prince of Wales Island. The Tolstoi Mountain project was a part of a program for investigating mineral deposits in Alaska, under the general supervision of R. S. Sanford, acting branch chief.

Jan 1, 1948

By J. S. Hansen

The U.S. Bureau of Mines developed a system for casting unique, slotted steel armor by modifying the conventional expendable pattern casting (EPC) process that is normally used for making aluminum castings. Three innovations were added to the EPC process to make the successful adaptation: (1) Vacuum was applied to sand molds, (2) continuous narrow-necked feeding systems were used to permit the casting of thin walls, and (3) fixtures were designed to prevent pattern damage and to hold critical casting tolerances, Potential problems and defects are described.

Jan 1, 2010

By Martin H. Stanczyk

The direct dissolution of a typical zinc sulfide flotation concentrate by elevated temperature and pressure leaching was investigated. The concentrate assayed about 55 percent Zn, 32 percent S, 6 percent Fe, and 1 percent Pb and contained minor quantities of copper and precious metals. The influence of various factors on the dissolution of the zinc in acidic and ammoniacal pulps when using oxygen as the oxidant was determined. The tests revealed that the sphalerite was difficult to oxidize. Complete dissolution of the mineral required vigorous and intimate nixing of the gaseous, liquid, and sold phases. The addition of pyrite or sulfuric acid to water slurries of the concentrate was required to obtain a high zinc extraction when leaching under acidic conditions. The quantity of pyrite and acid used was about 0.125 and 0.25 pound, respectively, per pound of zinc sulfide contained in the leach charge. In tests with acid, about 96 percent of the zinc was extracted from the concentrate in 1 hour at 200° C. when the oxygen partial pressure was 75 pounds per square inch gage or higher. Leaching with a continuous flow of air as the oxidant gave results that were almost as good as those obtained when oxygen was used, In tests with air fed through the autoclave at 320 liters per hour, 95 percent of the zinc was dissolved in 1 hour, Acid leach solutions assaying approximately 58 grams Zn per liter and containing Fe, Ni, Cr, and Cu impurities were produced in the better tests. The leached residue consisted essentially of red iron oxide together with substantially all of the lead and precious metals.

Jan 1, 1961

By F. Petersen, W. van Dyk, J. Bonsu, A. Isafiade

"This paper aims to demonstrate how a systemic approach can be applied to the analysis of the causes of accidents in South African mines. The accident analysis framework used was developed previously by the authors from the combination of the Mark III version of the Swiss Cheese model, Incident Cause Analysis Method (ICAM), the Nertney Wheel model, and safety management principles. Data on 91 accidents occurring from 2010 to 2012 at the site of a platinum mine in South Africa were used to populate the newly developed framework. The results obtained show that while routine violations (45% of all accidents analysed) were the most common form of human error, problems in the physical environment of workers were the most common workplace factor (39.6% of all accidents analysed). Furthermore, inadequate leadership was found to be the most common systemic factor responsible for accidents (51.6% of all accidents analysed). Some workplace factors were more commonly associated with particular unsafe acts than others, and some systemic factors were more associated with particular workplace factors than others. The outcome of this study demonstrates that systemic factors, rather than human errors and violations, are the chief causes of accidents in the mining sector. IntroductionThe mining industry is a very important sector of the South African national economy. A major factor threatening the sustainability of this industry is mining accidents, which frequently result in injuries or deaths, destruction of property, and pollution of the environment. In the past, mining accidents have led to the shutdown and threat of shutdown of mines (Ryan, 2008; Mail and Guardian, 2011). The country stands the risk of incurring significant losses if the mining industry continues to experience shutdowns. In 2012, the mining sector accounted for R262.7 billion (equivalent to US$32.83 billion) representing 8.3% of GDP directly, on a nominal basis (Chamber of Mines of South Africa, 2013).Mining safety is a global concern and has attracted significant international attention. This has precipitated various studies into different aspects of mining. Unfortunately, human error has been blamed for the majority of these accidents. A study by the US Bureau of Mines found that human error is the cause of almost 85% of all accidents (Patterson and Shappell, 2008). In Australia, it is the cause of two out of every three occupational accidents (Patterson and Shappell, 2008). Various mining companies maintain that they run efficient systems, and hence the behavioural problems of workers are to blame for most accidents. An understanding of accident causality could be a major step in the quest to reduce accidents. Only with a good understanding of the accident process can effective remedies can be designed."

Jan 1, 2017

By Frank J. Susko

The U.S. Bureau of Mines has developed a computer model to describe a flotation process. Coal data from conventional flotation has been converted to a simple, two-parameter kinetic model developed by Reuter and van Deventer (1,2)3. Each set of coal data was represented by two constants, a and ß, and an average flotation rate. The success of the model was demonstrated when the calculated and experimental recoveries showed good correlation. The two-parameter model allows complex data to be defined much more efficiently than traditional knowledge-based models.

Jan 1, 2010

By Takaaki Ishikawa

The distribution equilibria of lead, zinc and copper between CaO-Si02-Ah03 melts and liquid copper were measured at 1623K under a controlled H2-C02 atmosphere. The distribution ratios were plotted against the oxygen partial pressure, and reasonable oxide forms dissolved in the melts were estimated from the slopes of the plots. The activity coefficients of zinc oxide (ZnO), lead oxide (PbO) and cuprous oxide (CuOQs) increased with increasing slag basicity, defined by Xcao /XSiO, The temperature dependence of the activity coefficients was also measured.

Jan 1, 2003

By Randy Martin

"Greenstone Resources Ltd. constructed and operates the Santa Rosa open pit, heap-leach gold mine in Veraguas, Panama. The project was commissioned in 1995 at a designed capacity of 1.8 million tons per year. The ore exhibits a long leach up to three years, and requires three stage crushing to minus 3/8 inch to achieve on average a 74% gold recovery. The crushing plant is required to handle high volumes of clay and the circuit includes a Barmac Crusher. Panama receives over 3 meters of rain annually and Greenstone is using innovative means to control the project's water balance. Greenstone has developed a successful approach to operating a low grade (1.5 gm Au/T) deposit under difficult operation conditions.ABSTRACT ONLY"

Jan 1, 1997

By Edmund Shaw

This paper is one of a series being prepared by the United states Bureau of Mines describing mining and milling methods and costs at industrial mineral plants throughout the United states. These papers are designed to disseminate technical information regarding the methods and equipment used. The cost tabulations represent operating expenditures only and not total production costs. It is recognized that publication of total production costs might, in many instances, cause embarrassment to individual producers as well as to the industry as a whole. On the other hand, operating costs are essential to the technical discussion and study of the methods employed. The attention' of the reader? is specifically called to this differentiation in order that no misunderstanding of the scope of the cost tabulations shall ensue. P. J. Weisel, Inc., with office at La Habra and plant at Corona, Calif., is the only local company that produces sand for the Los Angeles glass factories, although silica sand for other purposes is produced in other parts of southern California and the adjacent portions of Nevada. The deposit at Corona consists of coarse sand imbedded in a whitish clay and differs greatly from the other deposits, which are fine-grained sandstone that must be crushed before it can be screened and washed. The preparation of Corona sand has to be thorough and includes grinding in tube mills, repeated washing and rinsing, removal of dust by air separation, and magnetic separation of iron and other minerals. This requires a plant with a complicated flow sheet. The first plant built did not make a. satisfactory glass sand, and many additions and changes were necessary. It is thought that the present flow sheet will remain substantially unchanged until a new plant is built. The design of a new plant would be simpler, but the process would be the same.

Jan 1, 1937

By EDER DOMINGOS OLIVEIRA, Leandro Viana Teixeira, Carlos Antonio Morais, Ruberlan Gomes Silva

Special attention must be considered in the production of high-grade rare earth products, such as mixed rare earth oxalates or carbonates. In the main minerals used industrially, the rare earth elements (REEs) are finely associated with impurities like calcium (Ca), magnesium (Mg), manganese (Mn), iron (Fe), aluminum (Al), thorium (Th), uranium (U) and phosphorus (P). Most of these impurities must be removed to avoid losses of rare earth oxides (REOs) as well as to prevent product quality degradation and low operational performance in the downstream steps of solvent extraction or ion exchange. The present study aims at investigating the conditions required to precipitate REEs, either as rare earth oxalates or carbonates, from purified rare earth sulfuric liquor with low Al3+ and UO22+ concentrations and very high Ca2+, Mg2+, Mn2+, and SO42− impurity contents.

By Georg Masing

Jan 1, 1933

By R. H. Coloquhoun

"INTRODUCTIONDome Mines Limited is located on 3,149 acres in Tisdale, Whitney and Shaw Townships in the City of Timmins in Northern Ontario. The mine and mill facilities are two miles from the town of South Porcupine, now part of greater Timmins.In April of 1909, J.S. Wilson of Massey, Ontario headed a party of prospectors into the Porcupine region. Disembarking from the Temiskaming and Northern Ontario Railway at mileage 222, they established an initial camp on the shore of Frederick House Lake. Following the lake ""break up"" they canoed to their destination, Porcupine Lake, and established a base camp on the west side of the lake by May 23, 1909. At a point approximately two miles from Porcupine Lake the moss on an outcrop was rolled back and gold was discovered.In the spring of 1911, the first mill structure was in the process of being built and consisted of 40 stamp mills, five S'x22' pebble mills and the ancillary equipment for a 300-400 T.P.O. operation. This structure was destroyed along with much of the Porcupine Camp by the famous Porcupine Fire of July 1911. By mid-1912, a steel ""fire proof"" structure was built and utilizing the salvaged mills from the fire, supplemented by the installation of three, 8'x30"" cylindro-conical Hardinge ball mills purchased third hand from Vipond Mines, processed 75,088 tons by year's end.The mill was again levelled by fire in October of 1929, this time caused by an overheated boiler stack. This 11 fire proof"" structure was immediately replaced by a wood structure and again the three Hardinge conical mills and the five 5'x22' pebble mills were restored and utilized. The new mill operated close to its daily capacity of 1500 tons during the last two months of 1930. During the rebuilding phase, the crushing plant was remodelled and a new crusher installed. These plants were protected from fire by a 60,000 gallon water tank and an automatic sprinkler system."

Jan 1, 1984

By J. A. Burger

Research in the eastern U.S. has shown that productive mine soils and forests can be restored using the following guidelines: (1) cooperation among the mine operator, landowner, and regulatory authority in developing the mining permit; (2) replacing topsoil or creating a desirable medium in which trees are planted; (3) loosely grading non-compacted topsoil; (4) using native and non-competitive domestic ground covers that quickly protect the site; and (5) planting a proper silvicultural mix of crop trees for their commercial value along with nurse trees for wildlife and soil improvement.

Jan 1, 2002

By B. V. P. Rao, H. L. Lovell, G. Simkovich

In the study described here, flotation tests were conducted on pure CaF2, on CaF2 doped at several concentration levels with either NaF or YF3, and on natural fluorite samples containing various amounts of impurities in an effort to extend previous knowledge of the influence of crystalline point imperfections on the flotation properties of solids. The results of these tests showed that although recoveries generally decreased as impurities increased, the differences in recovery were not nearly as striking as those detected in earlier experiments. A number of experimentalists have shown an interest in the way in which crystalline point imperfections affect the flotation properties of solids. As long ago as 1953, Welch hypothesized that it might be possible to control surface imperfections and thereby also control the flotation of solids.' A few years later, in some rather extensive work, Plaksin and his coworkers varied the surface imperfections of a number of compounds by oxidation or reduction processes and found that significant variations in flotation properties resulted.2-4 More recently, Simkovich showed that the recovery of both AgCl and PbS could be markedly varied by adding solid-solution impurities, which acted as doping agents, to these compounds.5 Then Mular studied the flotation of ZnO as a function of the doping agents Al2O3 and Li2O.6 Once again, it was found that these impurities, even in very low concentrations, had profound effects upon flotation recoveries. From an imperfection point of view, the defect structures of the compounds tested previously are as follows:7 PbS — amphoteric semiconductor with a Frenkel-type defect structure in the cation sub-lattice.8 AgCl - ionic conductor-Frenkel type defect structure? ZnO — n-type semiconductor, zinc ion interstitials and quasi-free electrons.10 All of these works undoubtedly bear some relation to the findings that the flotation properties of seemingly identical minerals from different ore deposits often exhibit extreme variation in flotation behavior, i.e., that small amounts of analytically undetectable impurities often have a great influence upon flotation

Jan 1, 1969

By L. W. Beckstead

The use of acid ferric sulfate solution as a lixiviant for chalcopyrite concentrates has been of little interest from a practical standpoint due to the formation of a tenacious layer of elemental sulfur which severely impedes the reaction progress. CuFeS2 + 4Fe+3 ?Cu+2 + 5Fe+2 +2s° For example, an acid ferric sulfate leach of chalcopyrite concentrate results in only 12% copper extraction in a three hour leach at 93°C. Experimental results suggest that particle size is the only controllable variable which has a significant effect on the rate of acid ferric sulfate leaching at ambient pressure. Size reduction of the concentrate prior to leaching was exam¬ined using various methods of grinding. Of the grinding methods considered, attrition grinding was found to be the most effective. Leaching of an attritor-ground product (median particle size 0.5 microns) resulted in approximately 90% copper extraction in a three hour leach at 93°C. Energy measurements suggest that the costs associated with attrition mill¬ing are not unreasonable. Evidence indicates that "activation" or stored strain energy is not responsibile for the enhanced reaction kinetics of the finely ground concentrate, but rather the experimental results can be explained simply in terms of the increased surface area due to size reduction. Leaching reaction mech¬anisms operative in the acid ferric sulfate system are discussed and the application of ultra-fine grinding technology to other systems is considered.

Jan 1, 1976

By Lawrence A. Ph. D. Hansen, J. David Deatherage

Laboratory testing programs were conducted to investigate the performance under compression loading of several types of geomembranes and geotextiles proposed for use in heap and dump leach projects. Synthetic liners of several thicknesses were sandwiched between representative subgrade soils and cover materials, thus modeling in the laboratory the actual installation conditions expected. Performance was evaluated by visual inspection and vacuum testing. Several testing procedures and equipment were used to investigate the effect of these testing parameters on the predicted performance.

Jan 1, 1987