Search Documents

INDEX TO TRANSACTIONS After a delay of many months, which is very much regretted, but which, it is hoped, will be one means of insuring a volume of accuracy where accuracy is very important, the Institute now has for distribution copies of the index of Volumes XXXVI to LV, inclusive. This is more than a mere index off names of authors and titles of papers. Every important topic under consideration by author or discusser is introduced under such key-word as will enable an engineer to locate the desired information with the minimum expenditure of time. This index sells for $5* in half morocco binding and $4*. in paper covers. With the index of Volumes II to XXXV (which sells for $5 in half morocco and $4 in paper covers), it forms a complete index of the first fifty-five volumes of the Institute's Transactions. These collective indexes are very valuable to members of the Institute, enabling them to look up matters in their own library; if they have the volumes to which the indexes refer, they can get the information at once, and, if not, they can readily determine whether or not a visit to a nearby public library is desirable.

Jan 7, 1918

By Tomio Tsuchiya

A construction method of bored steel H piles enclosed in soil-cement columns was developed by modifying steel H piles from the driven pile method and soil-cement walls from the earth retaining wall method, the latter of which produces cut-off walls and reduces noise and vibration during construction. In this method, as shown in Figure 1, rich mix cement paste is injected into the bottom of a borehole which is pre-excavated by a casing auger, then a steel H beam is inserted before it hardens. Since the high vertical resistance of piles created with this method has already been confirmed by loading tests, we have been investigating the applicability of this method for piles used to temporarily support building loads for top-down construction on raft foundations until the raft foundation is completed. However, in the loading tests, the bearing capacity at the lower end of the pile was measured by loading from ground surface on test piles which had friction cut to eliminate the shaft friction resistance. In other words, the loading tests neglected the effect of overburden pressure of soil above the lower end of the pile. To investigate the effect of the overburden pressure on the bearing capacity at the lower end of the pile, loading tests were carried out on a bored steel H pile of lm diameter (test pile) bored in a compacted sandy soil layer with N-value of 100 to 250 at each stage of a three-step excavation. The results show no significant change in the bearing capacity at the lower end of the pile when the depth ratio of the pile is in the range of 5.7 to 22.7.

Jan 1, 1996

By B. W. Haynes

With the national focus on energy, the combustible fraction of urban refuse is being extensively considered as a fuel supplement for coal in the generation of heat and power. The objective of these analytical studies by the Bureau of Mines was to determine the concentration of major, minor, and trace elements in the combustible fractions collected at various locations in the Bureau's urban refuse recycling pilot plant located at College Park, Md. The samples processed through the plant were submitted by various municipalities that are considering resource recovery as an alternative to landfill or other means of disposal. Twenty-five elements were determined in samples from six geographic areas and were compared with element concentrations found in typical coal samples.

Jan 1, 1977

By S. D. Michaelson

Open pits and quarries are the major sources of all "hard rock" tonnage mined today. Normally, ore is fractured from the pit face by blasting and then truck-hauled to a primary crusher where pro- cessing begins; overburden (or waste) is generally truck-hauled from the pit to dump areas. Truck haulage of blasted ore and overburden accounts for some 25 to 50% of total mining costs in a typical open pit and commonly is the largest single cost factor. Obviously then, cost reduction efforts should properly focus on improving existing haulage systems and developing new breakthrough techniques for material transport. Continuous flow systems for large tonnages ordinarily will result in a lower cost than batch systems such as truck or rail haulage. Continuous flow with pipelines for liquids and slurries, or conveyors for medium to coarse dry materials (in the -8-in. range) are the economic answers for bulk materials handling over reasonable distances.

Jan 11, 1968

By Zabetakis M. G.

This Bureau of Mines report presents a brief summary of the explosion trends in United States coal mines for the past 160 years. These trends show that in spite of the overall improvements in mine safety, the number of fatalities from ignitions of methane has actually increased in recent years. Suggestions are made of procedures that can be utilized to reverse this trend.

Jan 1, 1973

By J. Salazar

This paper presents a dynamic simulator of the semi-autogenous grinding operation deduced from first principles (non-stationary population balances) coupled to a Model-Based Real-Time Optimization (MBRTO) system to study optimizing strategies for an industrial semi-autogenous mill using genetic algorithms. For the design of the MBRTO both a validated first-principle steady-state model adapted on-line and a dynamic model were used to study the transient effect. The objective function considered is to maximize the ore throughput or the fine-product rate by changing the power-draw. For these purposes, these two performance indexes were introduced as fitness functions in the genetic algorithms. The three decision variables used were the ore feed rate, the water feed rate and the mill rotating velocity. The optimization problem was solved using a classical genetic algorithm with constant population. Constraints in the power draw and the filling level were handled by assigning a penalty function to the fitness function. Simulation results using industrial data for a large 1800 t/h copper-ore mill show the effectiveness of the system in finding the optimum controller set-points as a function of the process-operating constraints; mainly maximum ore feed rate, power draw and filling level. Starting from non- optimum conditions, the optimizer is able to improve the global performance index by 50% relative to a base case.

Jan 1, 2007

By P. Schwarzkopf, J. H. Brophy, J. Wulff

A constitutional diagram has been proposed for the tantalum-rhenium alloy system. Rhenium dissolved in tantalum up to 48 wt pct, and the maximum solubility of tantalum in rhenium is 5 wt pct. Intermediate x and s phases were found. X-ray diffraction, metallography and melting points were employed. SEVERAL investigators have described the phases present in the tantalum-rhenium alloy system, but no detailed account of the phase diagram prior to the present investigation appears to be available. Greenfield and Beck' reported the solubility of 48 to 54 at. pct Re in tantalum, a s phase at 41 at. pct Ta, and x phase isomorphous with a Mn from 37 at. pct Ta to less than 25 at. pct. They employed as-arc melted specimens and heat treatments at 1200 °C lasting 72 hr.2 Duwez3 reported the existence of a a phase at the composition Re3Ta2. Niemiec and Trzebiatowski4 observed a lattice parameter a = 9.69A, for the x phase at a composition Ta7Re22, but no s phase. Savitiski and Tylkina5 have shown a hardness maximum at the composition 40 at, pct Ta and a somewhat lower plateau from 35 to 10 at. pct. Knapton6 indicated results similar to those of Greenfield and Beck.' The present investigation describes the phase relationships in the tantalum-rhenium alloy system determined by melting point measurements, X-ray diffraction and fluorescence, and metallography. EXPERIMENTAL PROCEDURE Commercial 99.7 pct Ta powder from Fansteel Metallurgical Corp. and 99.9 pct Re powder from Chase Brass and Copper Co. were used for alloy preparation. The powders were weighed to desired nominal compositions and then pressed without binder into compacts weighing 5 or 10 g. The compacts were arc-melted six times on alternate sides on a water-cooled copper hearth using a nonconsumable tungsten electrode in an atmosphere of titanium gettered helium, at a pressure of 500 mm Hg. In most cases this procedure yielded alloy buttons of satisfactory homogeneity. A series of alloy specimens were analyzed wet chemically for use as standards for X-ray fluorescence. All specimens were analyzed by fluorescence and the results showed that the compositions differed by less than 3 pct Re from the original as-weighed nominal composition.* On the basis of self-

Jan 1, 1961

By L. Mair

A STUDY by J. R. Low, Jr.1 on the effect of quench aging on the Charpy-impact specimens of semikilled 1020 steel disclosed that a decrease in cooling rate from 1275°F raised the transition temperature. This was demonstrated in his investigation by controlling the cooling rate of impact specimens to duplicate that of a heavier plate and com- paring the properties with air-cooled specimens and quenched specimens. The transition temperature of the samples that had been cooled at a rate estimated to be similar to that of an air-cooled 3/4 in. plate was approximately 45ºF higher than the quenched samples. The transition temperature of the air-cooled series was between that of the slow-cooled and the quenched series. On the basis of this work, it appeared that the cooling rate of plates after rolling in a hot mill would have a bearing on the brittle fracture of the

Jan 1, 1955

By J. Font

New approaches for the fire refining process of blister copper have been carried out at the Codelco Norte Smelter. These have been mainly focused on modification and improvement of the process configuration based in fluid-dynamic and metallurgical studies of the oxidation and impurity treatment stages. This paper presents the results of the laboratory simulations and industrial tests performed in the 250 t anode furnace, evaluating two different process configurations: ? Bottom Bath Agitation System in the vessel during the oxidation stage, ? Dual Flux Injection System during the impurity treatment stage. The results show the possibilities of effective removal of high content of sulfur from the melt during the oxidation stage by using the bottom bath agitation. The use of the dual injection system demonstrated the significant improvement in the removal efficiency of impurities. Cu2007

Jan 1, 2007

By Ross I. Kelly

Carbonate rocks are widespread throughout Ontario and provide raw material for more uses than perhaps any other rock type. The principal carbonate rocks that are used by industry in Ontario are Paleozoic era limestone and dolostone. Limestone is a sedimentary rock that is composed mainly of the mineral calcite (CaCO,) while dolostone, also a sedimentary rock, is composed mostly of dolomite [CaMg (CO,),l. The majority of the province's limestone and dolostone extraction occurs from Paleozoic era rocks located in southern Ontario. Calcite and dolomite are also found in Precambrian marbles, calcite veins and carbonatites, however, utilization of these rocks by industry has been less common. Calcite and dolomite-rich rocks are utilized for a wide variety of uses including raw materials for cement and lime manufacture, chemical and metallurgical stone, fillers and construction aggregates (Derry, Michener, Booth and Wahl and OGS 1989a). For some uses chemical and physical requirements are very important. In the manufacture of glass, for instance, the chemical requirements of source materials are very important and very stringent. In other uses physical criteria such as whiteness may be more important. Although carbonate rocks are quite plentiful within the province, deposits that contain high concentrations of calcite or dolomite are somewhat limited. For that reason, this paper focuses on deposits that are known to, or may contain, a high percentage of calcite and/or dolomite. The paper emphasizes potential sedimentary limestone and dolostone resources, as these are the carbonate rocks most commonly utilized by industry in Ontario.

Jan 1, 2001

By James T. Curry

The steady growth of the Northwest portion of the United States over the past two decades, and the very rapid development of Northern California, Western Nevada, and Oregon in particular, led the Calaveras Cement Company people to Shasta County, California in 1957. The presence of a large deposit of high calcium carbonate limestone had been recognized for many years, but it required the momentum of an expanding economy to make these long known reserves valuable. This, plus the availability of a reliable supply of fuel in the form of natural gas, and the ready means of shipping the product to the consumer both by highway and railroad, seemed to offer the proper combination to launch a successful venture. The Calaveras Cement Company had been manufacturing cement by the wet process since 1925 at their plant at San Andreas, California. Starting with two small kilns, the plant in Calaveras County started an expansion program in 1945 that ultimately resulted in the plant as it exists today, consisting of five kilns with a combined production of 4.5 million barrels annually.

Jan 1, 1967

By Edward Thimons, William A. Hertbrink

The effect of wind speed upon aerosol penetration into an idealized enclosure was studied The idealized enclosure was a painted plywood box that was 1 2X1 2 XI meters in volume Two fans supplied 1 7 m3 /min of filtered air to this enclosure at a static pressure of 2 8 mm of water The enclosure had a 7 5 cm diameter vent port which was isolated from the air flow around the enclosure To simulate holes in real enclosures, three 16-cm diameter holes were drilled on the front and back sides of the enclosure This simulated enclosure was placed in a tunnel-like structure The air flow from an ultra-light air craft was directed at the front of the enclosure The air speeds were varied between 14 and 36 km/hr as measured by rotating vane anemometer Static pressure in the enclosure was measured with an electronic manometer Two optical particle counters measured the particle number concentration of particles between the 0 35 to 0 5 µm inside and outside of the enclosure Aerosol penetration into the enclosure was computed as the ratio of the aerosol concentration inside the enclosure to the concentration outside of the enclosure The enclosure static pressures measured increase from 2 8 to 3 4 mm of water (P=00001) Aerosol penetration into the enclosure increased linearly with air velocity above 20 km/hr Theoretically estimated penetrations were correlated with observed penetration into the simulated enclosure When simple linear regression was used to model the observed penetration as a function of the estimated penetration, the value of the slope was 0 69±0 12 and the P value for the regression model was less than 0 0001 These results indicate that enclosure static pressure needs to be higher than the wind's velocity pressure in order to minimize aerosol penetration into these enclosures

Jan 1, 1999

By S. M. C. Santos

Preliminary bench-scale studies were carried out on the leaching of a zinc sulphide concentrate from Somincor, Portugal, and the purification of the resulting pregnant solution using solvent extraction techniques. The sulphide concentrate contained 36% Zn, 36% S, 2% Fe and 4% Cu. The leaching was carried out with sulphuric acid in the presence of ferric sulphate as the oxidant. Important leaching parameters, such as the effect of reaction time, the solid-liquid ratio, temperature and concentrations of acid and oxidant, were investigated. After leaching, the recovered solution was contacted with an organic phase containing Acorga 5640 to remove the copper. Subsequently, the removal of iron from the leaching solution was achieved with a mixture of Cyanex 272 and TBP. This solvent mixture was relatively selective for iron over zinc. The stripping of the loaded solvent was performed with 200 g/L H2SO4. Six countercurrent extraction stages achieved a separation of about 99% of the iron from the leaching solution. The iron-free leachate can be further treated to recover minor metals by cementation, and finally, zinc by liquid-liquid extraction. The advantages of the suggested process relative to the traditional jarosite process are discussed.

Jan 1, 2006

Consolidated Rutile Limited (CRL) was one of the best performing mining stocks of the turbulent 1980s, having a very high payout of franked dividends. In contrast to some other mining groups, it was not highly involved in the speculative lead-up to the 1987 sharemarket crash. Its base was firmly laid through a succession of decisions that were taken in the period 1982-1985. These decisions and the rationale behind them are outlined in this paper. CRL began the 1980s in a highly favourable position. It had successfully pioneered the transition to high-throughput mining of the high dunes on North Stradbroke Island (NSI), commissioning its 2100 tph cutter suction dredge at the Bayside reserves in 1978 at the time of rising prices, such that it was able to pay off its modest bank loan within 18 months. The June 1980 results showed a record after-tax profit of $5.6M, from total assets fo $26.5M and sales tonnages of rutile and zircon of around 50,000 tonnes each.

Jan 1, 1991

By Stoyan N. Groudev, Ioannis Paspaliaris, Irena I. Spasova, Kostas Komnitsas

"Acid mine drainage waters generated in the uranium deposit Curilo, western Bulgaria, were treated by means of a constructed wetland located in the deposit. The waters had a pH in the range of about 2.5 - 4.1 and contained uranium, radium, some heavy metals (iron, manganese, copper, zinc, cadmium, cobalt, nickel, lead), arsenic and sulphates in concentrations much higher than the relevant permissible levels for waters intended for use in the agriculture and/or industry. The wetland covered an area of about 140 m2 and was characterized by an abundant water and emergent vegetation and a diverse microflora. Typha latifolia, Typha angustifolia and Phragmites australis were the prevalent plant species in the wetland but species of the genera Juncus, Eleocharis, Scirpus, Carex and Poa as well as different algae were also well present.The water treatment was started in July 2001 and until now (August 2002) the wetland effluents were characterized by pollutants concentrations decreased below the relevant permissible levels. The water flow rate through the wetland during this period varied in the range of about 0.2 - 1.0 l/s. The water clean-up markedly depended on the temperature but was efficient even in the cold winter months at air and water temperatures close to 0oC. The removal of pollutants was due to different processes but the microbial dissimilatory sulphate reduction and the sorption of pollutants on organic matter (viable and dead plant and microbial biomass) and clay minerals played the main role. Negative effects of the pollutants on the growth and activity of the indigenous plant and microbial communities were not observed."

Jan 1, 2003

By Kenneth K. Humphreys

INTRODUCTION At the time the 4th edition of this book was published in 1979, the coal industry had experienced a sharp upturn in prices for its product. From 1950 throgh 1969, steam coal prices had held almost flat at about $5 US per st (about $5.50/t). Thus, when considering the effects of inflation, the price of coal had actually been declining for two decades. The passage of the Coal Mine Health and Safety Act in 1969 and its cost effects started an upward trend in coal prices which was rapidly accelerated by the effects of the Mid-East oil embargo in 1972. Prices of steam coal on the spot market eventually climbed to over $30 US per st ($33/t) and higher in some cases. Metallurgical coal prices skyrocketed in a similar manner and the industry at long last appeared assured of an adequate return on investment. Many companies did expend large sums of money to upgrade and expand their mining and preparation facilities. Unfortunately the bubble eventually burst, in great measure due to the downturn in the US domestic steel industry and the resultant decline in metallurgical coal demand, loss of export markets to other nations and even imports of large amounts of foreign coal to the United States, and more stringent environmental regulations which made many high sulfur coal measures uneconomical to mine. Compounding the problem was the rapid world decline in oil prices in the mid-1980s which encouraged many consumers to utilize oil rather than coal. During the 1980s, metallurgical coal dropped over 20% in price, which, when considering inflation, actually amounted to about a 40% decrease in value. Export coal decreased a similar amount in price. Steam coal prices held nearly constant, thus also losing considerable value when inflation is considered. All of these factors make it even more imperative than ever that the industry do everything in its power to make wise economic decisions and to examine carefully all existing operations and planned future expenditures to be certain that their full cost implications are understood and that they can be justified on the basis of an adequate return on investment. It cannot be assumed that the price of coal will increase. To the contrary, as indicated previously, when considering inflation, coal decreased in value in the 1980s, just as it also did in the 1950s and 1960s. The price surges in the 1970s merely were a catchup game, and in truth the true market value of coal is in reality even lower than it was in 1950. CAPITAL AND OPERATING COST ESTIMATION Prior to constructing a new plant or expanding existing facilities, a detailed preliminary cost estimate is necessary to determine the capital investment

Jan 1, 1991

By R. H. Waddington

Historical The limitations of reverberatory furnace operation have prompted many investigators to consider electric furnaces for melting electrolytically refined cathode copper. In the majority of cases where experimental work was performed, the furnace used was of the granular resistor, induction, or indirect-arc rocking type, and attempts to adapt the three-phase direct-arc furnace to copper melting appear to have been relatively few. In 1935, the International Nickel Company of Canada, Limited, carried to an advanced stage its experimental investigation of continuous melting of copper in the three-phase direct-arc furnace, and demonstrated that this process was technologically and economically practicable. Trial operations were conducted at the Huntington, W.Va. works of the Company, and were followed by the installation at Copper Cliff, Ontario, in 1936, of a full-scale unit for commercial operation. Two years later, a second unit was installed -which raised the electric melting capacity to a point permitting complete replacement of the coal-fired reverberatory furnace operation in the production of refined copper castings.

Jan 1, 1946

By Walter R. Lawrence

Newmont Gold Company, formerly Carlin Gold Mining Company, is a publicly owned corporation, 95% owned by Newmont Mining Corporation. Newmont Gold Company has operated gold recovery operations North of Carlin, Nevada, since 1965. Development of the Gold Quarry ore body, 19 kilometers south of the original mine, resulted in the decision to construct gold recovery and ancillary facilities in what is referred to as the Southern Area. Plant No. 2, located 11 kilometers North of Carlin, Nevada, was designed to treat 6350 tonnes per day of oxidized gold bearing ore assaying 2.5 grams per tonne of Au at an average recovery of 87%. Flowsheet development conducted by Newmont personnel resulted in the decision to construct a carbon-in-pulp recovery circuit preceded by two-stage grinding, Detailed engineering was done at Toronto by Bechtel of Canada beginning on January 1, 1984. Actual construction began on March 1, 1984, and was completed in June, 1985. First feed was run on June 22, 1985.

Jan 1, 1987

By A. W. Randall

Geological Aspects of Ore Reserve Estimates of Pine Point District Zinc- Lead Deposits, N.W.T. Zinc-lead ores of the Pine Point District, Northwest Territories, Canada are hosted in paleokarst cavities within a Middle Devonian carbonate barrier complex. Of the nearly 100 deposits found, most are irregularly distributed along two main regional stratigraphically controlled trends. The ores, which occur predominantly as open space filling, form deposits most of which average one million tonnes in size with an average grade of 10% combined zinc plus lead. Geological features related to karsting control not only distribution of deposits but also their shape, size and grade. The higher grade ore in these deposits generally occurs in a relatively small core area. Consequently, accuracy of reserve estimation is dependent on drill hole density and understanding of karst geometry. Several case examples will be reviewed to demonstrate the relationship between shape, size and grade of deposit, geological reserves and drill hole density, along with a discussion of geological ore reserve estimation methods.

Jan 1, 1985

By W. C. Hagel

In 1952, Hauffe and pfeiffer1,2 reported that parabolic rates of nickel oxidation are decreased by factors of two and four at 1100° and 1000°C, respectively, when Li2O vapor is present. Hauffe 's3 explanation was that monovalent lithium enters the crystal lattice of p-type NiO to decrease cation-vacancy concentration and, hence, diffusion of Ni2+ ions across the growing oxide. After first succeeding in adding lithium directly to molten nickel, the purpose of this investigation was to determine whether alloyed lithium is a more effective oxidation inhibitor than the external vapor. Seven 650-g heats were prepared by melting carbonyl nickel inductively under 1 atm of argon. Various amounts of lithium were added by dropping small chunks into the melt. Only about 10-pct recovery was achieved with the remainder lost by spattering and volatilization. Nominal and actual

Jan 1, 1965