Search Documents

Beatrix Gold Mine, a deep-level gold mine in the Free State province of South Africa, has the highest methane emission rate of any gold mine in the country. Methane is emitted from underground sources intersected during mining operations and is liberated into the general mine atmosphere. The total methane emission rate for the mine is of the order of 16001/s and the South section of the mine emits approximately 10001/s of methane gas. The mine has a history of gas accumulations which have led to a number of underground explosions. Following the last explosion in 2001 and the subsequent investigation, a number of recommendations were made. Two of these were to consider extracting the underground mine methane to render the mine atmosphere safe, and to declare hazardous locations that require special operating procedures. A number of such workplaces have now been declared at the South section of the mine. Methane gas is a potent, explosive greenhouse gas whose contribution to global warming and climate change is 21 times higher than that of carbon dioxide. To reduce its inherent danger and to mitigate its global warming impact, a carbon credit project under the Clean Development Mechanism (CDM) of the Kyoto Protocol has been developed and implemented, the aim being to capture and destroy the methane at Beatrix mine. The mine has constructed an extraction system to capture and extract 400 (Is of the methane. Percentage methane (per volume) of the gas intersected at source is 85%, with negligible concentrations of other hydrocarbons and water associated. The mine contracted the services of Group Five to design and construct the flare and ancillary equipment on surface, and Promethium Carbon was contracted to assist with the carbon¬-related aspects, approval framework, and administration of the project. A number of design and construction challenges had to be faced to extract and transport the gas effectively to the surface of the mine as the emitters are approximately 3 600 m away from the mine shaft at a depth of 860 m. Further considerations were the requirements for the type of column to be used to transport the methane gas, the pressure loss over the system, the safety systems needed to address the risk factors involved in the transport of the methane gas, and a suitable pumping system to extract the gas to the surface. The system operates under negative pressure provided by two blowers on surface delivering the emissions to a flare capable of burning off 450 8/s of methane gas. In this paper a number of benefits for the mine are discussed. These include, but are not limited to, the removal of approximately 55% of the total volume of methane gas from the general body of the air in the geographical areas of the mine where the methane gas is emitted into the atmosphere, and reducing the risk of methane-related incidents. A further benefit of this project is the mitigation of the global warming impact of the methane gas and the reduction of the mine's carbon footprint by approximately 25%. This project could also assist in alleviating the energy shortage being experienced in South Africa by means of the planned generation of 4 MW of electrical power, utilizing the methane gas, as a second phase of the project.

Jan 1, 2011

IN December, 1905, a Forwood down-wheeler grinding pan (5 ft dialmter), and similar in design to those in use on the Kalgoorlie goldfields, was installed for experimental work in connection with fine grinding jig tailings.The galena remaining in this product is very finely (closely) mechanically disseminated throughout the blende and gangue, rendering fine crushing imperative for its liberation. A reswne of the milling process in vogue at the old mill will enable the series of operations to be more closely followed. The ore at the South Mine assays, on the average-lead...

Jan 1, 1909

By J. Don Scott

Analytical predictions of the rate and magnitude of settlement of deposited oil sands tailings slurries generally overestimate how fast pore pressures will dissipate. Field deposits of nonsegregating tailings to mature fine tailings show continued high pore pressures near the surface which impede surface reclamation. In geotechnical analyses which predict the consolidation behavior of soft soils a finite strain theory is used. Effective stress-void ratio and void ratio-hydraulic conductivity relationships determined from laboratory large strain consolidation tests, are used in the finite strain predictions. This theory, however, cannot predict the full range of sedimentation, consolidation and pore pressure dissipation which occurs in large scale deposits of thixotropic tailings slurries. A new large strain consolidation model which assumes that the creep rate of the slurry exceeds the pore pressure dissipation rate is being investigated. This model is relevant for rapidly deposited, low permeability thixotropic slurries where the upwards drainage path increases by several meters a year, such as, in oil sand fine tailings ponds and nonsegregating tailings deposits. The model will be verified by analyzing the 10m high column of fine tailings at the University of Alberta which has been monitored for over 20 years and in which the excess pore pressures are still very high.

May 1, 2004

By Worner H. K

Education has always been a topic to rouse the interest of mining and metallurgical engineers, but the recent activities of the Education Committee of the Australasian Institute of Mining and Metallurgy 1, 2, together with the moves throughout the Commonwealth to extend the field of technological education, have made the subject a very live one at the present time. The authors have felt it would be appropriate that on the occasion of the First Ordinary Meeting for 1950, in Victoria, some contribution should be forthcoming concerning the history, present status and possible future trends of mining and metallurgical education in this State. As for the past, the time approaches when there will be none having personal recollections of the beginning of Victorian mining schools or of the men who started them. As for the future, it is obvious that rapidly expanding metal-producing and metalconsuming industries will demand a greater output of competent graduates and diplomates. The era immediately ahead seems to be bristling with opportunities, but mining educators need to temper their enthusiasm for various policies and programmes with the realisation that they are helping to train men who will be leaders 15-20 years hence when the problems of industry and trials of life generally may be very different from what they are to-day.

Jan 1, 1950

By Henry F. Collins

The following notes on the cheap milling of a soft lowgrade ore-body in the State of Chiapas, Mexico, may be of interest. The ore-body in question was worked, not by itself, but incidentally in connection with a large extraction of concentrating-ore; and one 10-stamp battery of a 30-stamp mill used for re-crushing tailings, and provided with copper-plates, was set aside for the treatment of this particular ore, of which, during a period of 17 months, 10,274 tons, of 2240 lbs. each, were handled. Description.—The ore-body collsisted of that portion of a mass of decomposed garnet-rock of igneous origin, which, near its contact with another igneous mass, composed chiefly of the mineral wollastonite in a nearly pure state, had been permeated by solutions, depositing irregularly, throughout it, quartz, chal-

Jan 1, 1902

By J J. Culberson

The past 10 years has seen use of computers become widespread in the mining/exploration industry (including coal, precious and base metals, oil/gas and industrial minerals). This paper will concentrate on the use of computers as a tool to provide technical solutions (including data management, mine planning and operational support) to this industry rather than the use of computers to aid accounting, maintenance and inventory (æcommercialÆ) applications. This paper will review the processes and benefits of the use of computers in mining. We then review the use of technical computing locally here in New Zealand and see what business benefits local users have found from using computers in mining. We have, in research for this paper, spoken with mining software vendors from around the world to find out what is currently the æbest practiceÆ in the industry. The paper will then list what those vendors see as the ultimate improvement on the cards for the future of mining software.

Jan 1, 2000

By Michael J. Brown

It is often necessary to undertake some form of pile testing to verify design calculations. Historically this has been limited to static and dynamic tests. Newer rapid testing methods such as Statnamic are seeing more frequent use. This form of testing can be advantageous due to short set up time and test duration. Although the methodology suffers from a lack of formalised guidance and may prove difficult to analyse in certain soil conditions. This paper investigates the suitability of Statnamic testing and analysis for a range of soil and pile types as well as different installation methods through a number of case studies undertaken in the UK. Recommendations are made on test specification and analysis.

Jan 1, 2006

A large lab apparatus was designed using a scale-down methodology based on the design legacy of the current FLSmidth commercial forced air flotation machines. This new apparatus, along with a new test methodology, was used to evaluate new rapid prototype concepts. The apparatus was designed to monitor bubble size, power, pumping capacity, Jg, velocity profiles, froth character, and tip speed. The methodology developed follows a sequence that goes from hydrodynamic tests and solids suspension tests to a flotation kinetic test. This methodology has been demonstrated to be a good tool to determine the effect of machine design changes on flotation.

Jan 1, 2012

By David S. Brown

What troubles me so often about debates over the environment, which I have heard since I entered government in the late 1960's, is that the issues are so often presented as a false dilemma--the either-or fallacy in logic. The either-or fallacy allows only two possible choices: Either protect the environment or exploit it. In reality, however, there may be a few more options. The diverse, often competing, values that the Earth offers require us to weigh and balance those options through a range of policy options. A quality environment and economic growth and opportunity are not mutually exclusive. First, let me acknowledge that I support a set of resource values recognized in U.S. laws and deemed important down through history for the success of free, progressive, and secure societies: the importance of access to raw materials. Increasingly, however, mineral raw materials have been viewed at best as not particularly relevant to a sophisticated, technologic society, and at worst monstrously destructive of our natural environment. Both perceptions, in my judgment, are wrong.

Jan 1, 1989

By R. Dahlke, J. A. Finch

A campaign was undertaken during the greater part of 2001 at Noranda’s Brunswick mine concentrator to investigate the role of gas (air) superficial rate (Jg) distribution to the cells in the final Zn cleaning stage (bank of seven cells), i.e. the Jg profile. Three profiles were tested: “balanced” (each cell with same Jg), “increasing” (from cell 1 to 7 proportionally), and “decreasing,” along with an “as found” profile in a parallel control bank. The experimental design allowed for two confounding factors, changes in ore type and circulating load. The increasing profile consistently gave the best metallurgy (down-the-bank grade / recovery). The reason for improved performance was the response of the first cells in the bank where the increasing profile gave the highest selectivity of sphalerite against nonsulphide gangue (NSG). The other profiles gave lower selectivity and higher zinc recovery in the first cells, which combined to reduce overall bank performance. The higher selectivity with the Increasing profile is attributed to the low gas rate in the first cells reducing water recovery and hence limiting entrainment of NSG. The increasing profile was subsequently configured for all four stages in the zinc cleaner circuit.

Jan 1, 2004

A comprehensive analysis of rock structures in non-oriented (axially oriented) drillcore is now available (Laing, in press). The system embodies new concepts which better equip the geologist and engineer to deal from the outset with optimising the acquisition of structural information in drillcore, logging: interpreting, and graphically presenting the results. The few existing techniques for determining orientations of structures are augmented by a wide range of new techniques, and all are brought together into two solution types by considering the underlying Euclidean geometries. Analysis of these solution types in terms of what data are required to implement each solution and what assumptions need to be made, leads to strategies which facilitate intelligent design of different drilling programs for blind and outcropping situations. Drillcore is variably structurally fertile, depending on the number of different structures present. This concept fosters the selective logging only of the more fertile core. Drillholes are also variably fertile, depending on their orientational relationship to the structures in the host rocks. Structural parameters are either vectorial or non-vectorial. Vectorial structures parameters comprise normal structural orientations plus polar vectors like vergence, younging, shear sense and so on. They can be determined by one of two solution types: external solutions, which use an external reference structure to fix the drillcore and thus permit orientation of all structures within that core, and internal solutions, which use orientational data from a selected structure at three or more different drillhole orientation to determine the unique orientation of that structure, without reference to any external structure. Both solution types rely on constant orientations (orientational stability) of the selected structure, but the internal solution actually provides its own test of orientational stability. External solutions are the norm in outcropping situations and internal solutions are invaluable in blind situations. In blind situations sequential "internal then external" solutions can be used respectively to provide a reference structure and then use this for subsequent external solutions at individual points downhole. Blind prospects can now be drilled and interpreted as easily as outcropping prospects. Each solution type has its own optimum requirements. External solutions are ambiguous for certain orientational relationships between the drillhole and the reference structure (for example, a perpendicular relationship), hence drillholes in which external solutions are planned should be designed to avoid these orientations. Internal solutions are ambiguous for straight drill paths, and are most unambiguously resolved when the drill path attains maximum drillhole dimensionality, that is, it occupies a wide variety of orientations in 3D space; hence drillholes in which internal solutions are planned should be designed as combinations of non-parallel holes or as individual strongly curved holes. For both solution types an understanding of the kind of structural fertility required leads to intelligent design of drill paths, which is termed structural drill targeting. It is distinct from spatial drill targeting, which is the process which defines and (x,y,z) point-or volume-target. Effective design of drilling programs requires both structural and spatial targeting. The external and internal solutions for vectorial parameters are implemented via (1) visual (qualitative), (2) stereographic, or (3) core orienting frame procedures. Each of these has its own advantages. Stereographic procedures have been simplified via the erection of a drillcore reference frame in which three fundamental angles are defined, and the formulation of an all-inclusive set of stereographic recipes for determining orientations from the measurement of these angles. Non- vectorial structural parameters comprise an ad hoc array of useful measures which are simply described by numbers. Examples are angles between structures, and density of structures. Such parameters (some of which provide useful vectors toward ore bodies) are invaluable in drillcore because they can be measured and recorded rapidly, without determining the orientation of the core. In a summary, non-oriented drillcore can now be structurally mapped exactly as if it were outcrop. Interpretation of the significant volume of unique structural information which is beginning to flow from this system can be optimised by using, in addition to the conventional cross section and longditudinal section, three new modes of presentation. The natural cross section is that section in space normal to a principal structure of interest. It is a section in which it is advisable to drill to obtain certain structural information, and in which the results need to be presented. A newly defined unique cross sectional orientational symbol is recommended for dramatic improvement in the quality of information presented in cross sections. Stacked level maps are a powerful adjunct to cross sections.

Jan 1, 1990

By J. E. Matta

The methane gas emitted from coal samples collected from the conveyor belts dumping into silos was measured by the Bureau of Mines. Approximately 50 pct of the total gas desorbed into a sealed can within 1 week was released during the first 24 hours. No simple correlation between the gassiness of the coal stored and the methane concentration in the silo open space above the coal was found. This was probably because the gassier coals were stored in open-top Silos, which were better ventilated. Although the methane concentration in the open space above the coal pile was less than 1 pct for all 34 silos investigated, a methane measurement in the coal pile showed that high methane concentrations can exist. The methane released in the pile appears to accumulate and not liberate freely into the open space above the coal pile. Probably this gas is released during reclaiming operations, but further research is required to substantiate this claim.

Jan 1, 1978

By D. D. Walker

Scheelite, the most abundant tungsten mineral in the Philipsburg region of Montana, is found in replacement deposits and along fissures and cracks in limestone at various distances from contacts with acidic igneous rocks. It also occurs at the limestone-igneous contacts, but typical garnet tactites are developed in only a few places in the region. The most favorable host rocks for scheelite mineralization are the Jefferson, Hasmark, and Madison limestones. Scheelite is exposed in float, outcrops, and surface and mine workings along a 2-mile-wide belt extending southwest from Lost Creek beyond Silver Lake, a distance of 15 miles or more. (See fig. 1.) Some scheelite is found in veins formerly mined for silver. Powellite and molybdenite occasionally are present with the scheelite. Hubnerite occurs in quartz veins in the Black Pine area 10 miles northwest of Philipsburg. These quartz veins occur in the quartzites of the Precambrian Spokane formation. Tungsten production in the region has come almost exclusively from scheelite deposits, both lode and placer. During a 6-year period beginning in 1943 a total of 142.0 tons of 63-percent W03 concentrate was produced by H & H Mines Co. In the early 1950's, the Trigger mine produced 4,000 tons of 1-percent W03 ore and the Tip Top 650 tons of 2.0-percent W03 ore and 2,906 tons of 2.2-percent ore. There has been sporadic production from some of the smaller properties in the area.

Jan 1, 1960

By F. Rosenblum, P. Spira

"Techniques were developed to determine the oxygen demand of sulphide ore pulps in the laboratory and in concentrators. The effect of variables which influence oxygen demand was studied, and it is shown that the oxygen demand is a measure of the degree of oxidation of the sulphide surfaces. It is suggested that in investigating the significance of oxygen in flotation, the oxygen demand of the pulp is a more suitable parameter than the dissolved oxygen content.Oxygen demand measurements are being carried out with a view to determining the effect of aeration on mill metallurgy and devising improved methods of predicting aeration requirements of sulphide ores.The importance of pulp oxidation in the flotation of massive sulphide ores has long been recognized. At the Noranda concentrator, chalcopyrite could not be floated satisfactorily without a pre-flotation aeration step because the necessary dissolved oxygen was consumed by the large amount of pyrrhotite in the ore. With aeration, pyrrhotite and pyrite were depressed by surface •oxidization, and the resulting thiosulphate level in solution gave a good indication of the end of useful aeration. 1'he present study was prompted by the need to find an alternative criterion for cases where recycled mill water may contain a relatively high concentration of thiosulphate. Preliminary experiments suggested that the rate of oxygen uptake by the pulp -its oxygen demand -might be a practical measure of the end point of aeration as well as a significant parameter in the flotation of massive sulphide ores.Although it has long been realized that oxygen is an important variable in flotation, analytical difficulties precluded detailed plant investigations. Measurements of' dissolved oxygen in mill pulps were first reported by Ralston(i) in 1929. A titration method was used, and because of the delay occasioned by the preparation of clear solution samples, the values obtained were believed to be low. It was quite evident, however, that pulps in the grinding circuit had a lower oxygen content than in flotation. More recently, Woodcock(2,3) used a polarographic probe to carry out oxygen surveys in six Australian concentrators and he generally observed a similar pattern. A large number of other solution parameters were monitored, such as pH, redox potential, reducing power, and reagent and metal concentrations, with the aim of detecting correlations among the measured variables. A few potentin.lly useful relationships were found ""or specific operations in certain plants."

Jan 1, 1974

By The Staff

"THE property of Red Mountain Mines Limited is located 11/2 miles north and west of the town of Rossland, in southern British Columbia. The mine is situated on the flank of Red mountain, famous in pioneer days as the site of a number of profitable gold-copper producers. Mining and milling commenced in May, 1966, and by the first of July the concentrator was treating close to its average design capacity of 400 tons per day. The following description of the property and its operations is divided into three parts, dealing respectively with geology, mining and milling.GeologyAll the known ore reserves of Red Mountain Mines occur on the Coxey claim, on the west slope of Red mountain. Although there are indications of molybdenite mineralization elsewhere on the Company's property, these have not been developed.The Coxey and adjoining areas are underlain by the Mount Roberts formation of the Rossland volca-nics. This formation consists of an interbedded series of volcanic and sedimentary rocks, mostly brecciated and silicified near the ore zone, and all intruded by igneous rocks which occur in various forms, and vary in composition from basic to acid. The country rock in the vicinity of the mineralization seems to be mostly a volcanic, approximately andesitic in composition, and possibly a surface flow. There is much banding, some of which is undoubtedly due to tuff and agglomerate layers, and some to narrow, siliceous, sedimentary horizons such as the surface exposure of the main ""A"" orebody, much of which was a thin capping of greyish banded rock that looked like quartzite. The drill holes also intersected occasional layers of black, argillaceous quartzite, sometimes altered to a greenish colour. The whole assemblage has been silicified with varied intensity, sometimes to such an extent as to have obscured or obliterated the original characteristics. The mineralized zone has also been strongly brecciated, the fragments varying in size from less than an inch up to large masses, best described as a mega-breccia. Anomalous results obtained in drilling, such as sedimentary sections that do not appear in adjoining holes, may sometimes be due to the presence of these large blocks, no longer in their original position. The whole volcanic unit is thus very complex and confusing. For practical purposes, the ore may be said to occur in a greenstone formation with minor sedimentary interbeds and considerable later igneous material."

Jan 1, 1967

Over half of the molten aluminium produced at the 52,000 tons/ year eapacity plant operated by Comalco Aluminium (Bell Bay) Limited in Tasmania is cast into saleable produets by the direct chill process. Considering the importance of direct chill casting to the aluminium industry it is surprising that so little published literature on the subject is available, although Easton (1947), Smart (1954), and Uppert (1940, 1944, 1945) have contributed much toward lifting the veil of secrecy surrounding the process.The direct chill, or D.C. process as it is commonly called when related to aluminium, consists basically of feeding molten aluminium or its alloys into; water-cooled mould from the bottom of which solid aluminium is continuously extracted. Although the casting procedure is continuous in principle, the equipment is normally operated in an intermittent manner. Castings up to 20 ft long are formed during a cycle. At the end of the cycle casting is stopped and the pit into which thc castings are dropped is cleared before a new cycle commences. Depending on the size of the casting in relation to the cross sectional area of the pit and the support mechanism (commonly a hydraulic ram), 'drops' of up to 15 tons are not uncommon. This method of D.C. casting IS termed vertical D.C. casting and is the one most commonly employed in the aluminium industry.Horizontal casting has come more to the fore in recent years with the casting being extracted from the mould in the horizontal plane and is a truly continuous casting method since flying saws can be simply used to cut the continuously cast shape into required lengths as it emerges from the mould...

Jan 1, 1967

By Clayr Alexander

Stillwater Mining Co. (SMC) is engaged in developing, extracting, processing and refining palladium, platinum and associated metals (PGM)from the J-M Reef. This geological formation is located in Stillwater, Sweet Grass and Park counties in southern Montana. Associated byproduct metals include rhodium, gold, silver, nickel and copper. SMC’s current mining operations are near Nye, MT. The company is currently developing a second underground palladium and platinum mine, the East Boulder project, about 21 km (13 miles) west of the Nye operations. A 5,650-m (18,550-ft) tunnel is required to gain access to the ore-bearing horizon (J-M Reef).

Jan 1, 1999

By J. Kemeny, J. Lyons-Baral

"Point cloud technology is now an indispensable tool in geological and geotechnical data collection, interpretation and analysis. Open pit and underground mines of all sizes are regularly collecting point cloud data as Laser Scanning (LiDAR) and Photogrammetry surveying devices have finally become affordable and the workflows fast and efficient. Past challenges of large data processing and manipulation are gone with recent technological advancements in computer hardware and software. These innovations reduce file sizes, ease rendering requirements and allow for the implementation of real-time 3D viewers and surface meshing tools. With its ability to remotely (safely), rapidly and accurately extract large quantities of georeferenced and 3D-oriented data, point cloud technology provides numerous applications to the geomechanical field. The list of uses is continuously growing, so this paper specifically focuses on digital outcrop modeling and digital terrain engineering. INTRODUCTION Point Clouds The high-resolution and increasing availability of point cloud technology is rapidly improving open pit and underground mines’ investigation, interpretation and characterization of site geology and rock mass properties (Kemeny et al., 2015; Lyons-Baral, 2012). LiDAR and photogrammetry are common remote sensing methods employed to measure the coordinates of surfaces in three dimensions (3D), providing the X, Y and Z locations, and typically the reflective intensity and/or the visible three-band color of each point (Figure 1). LiDAR uses either a time-of-flight or phase-shift measurement of a laser beam reflected off targeted surfaces and received back into the device. Photogrammetry generates point clouds by merging multiple overlapping photographs and uses stereographic plotting to define the locations of object points in 3-D space. These methods can be deployed from airplanes, unpiloted aerial systems (UAS or drones), tripods, land vehicles, and even in a mobile backpack shown in Figure 2. RADAR, Total Station-Prism and other remote sensing systems also offer very precise “point clouds”, but this paper does not address these due to their higher cost and lower versatility and mobility. Technology In the past few years point cloud acquisition device prices have dropped significantly, devices have become lighter, smaller and easier to operate, and processing and utilizing the data has also become faster and easier. Device size improvements include mobile backpacks (Figure 2) and handheld mobile LiDAR (CISRO, 2014), allowing mobile scanning in tight spaces both above and below ground or inside and outside of man-made structures. Airborne data acquisition options have expanded dramatically with the spread of UAS technology as seen in Figure 3 (Hexagon Geosystems, 2015). Once UAS usage regulations are sorted out, these versatile machines will be everywhere, offering high resolution coordinate scans, imagery and other remote sensing. While backpacks and handhelds allow access to tight quarters, UAS permit rapid data capture from narrow to broad areas with multiple perspectives reducing data “shadows.”"

Jan 1, 2016

Preparation of MgO Nano-Particles with Magnesite

Sep 13, 2010

"Qatar, crude petroleum, production, annualdata MY 1949-51Quality mine, Ark., coal, carbonizing properties TP 667washabilty study RI 496N. Dak., lignite, grindabilty as function ofmoisture, tests, results RI 5167"

Jan 1, 1960