Search Documents

By Paolo M. Brion, Z. Bade Sozer

"The Bypass Tunnel has high head conditions ranging from a minimum of 600 feet (183 m) under the Hudson River to a maximum of 875 feet (267 m) on the west side. The ground cover ranges from 425 feet to 900 feet (130 to 274 m). A two-pass lining is designed for the Bypass Tunnel. The bolted, gasketed precast segments carry the temporary hydrostatic and permanent ground loads. After the tunnel is put into service, the design assumes that the final lining, which varies from reinforced concrete to reinforced concrete with steel interliner, will carry the permanent hydrostatic loads. The design head for the segments is assumed at 775 feet (236 m), and the internal operating pressure head is around 1,200 feet (366 m). This paper discusses the design hydrostatic head and different load conditions considered for the segments, the load sharing between the segments and final lining, and the means employed to control water and hydrostatic pressure. PROJECT BACKGROUND The Rondout-West Branch Tunnel (RWBT), a segment of the Delaware Aqueduct, was built from 1937 to 1944 and provides about 50% of New York City’s total water supply. Monitoring and tunnel operations have shown that the RWBT is leaking up to 35 million gallons per day (MGD) (132.5 million L/day). In particular, two locations have been identified as areas of concern: Roseton and Wawarsing, as shown in Figure 1. The Wawarsing reach of the aqueduct will be repaired with an extensive grouting program when the RWBT is unwatered. However, because of the extensive nature of the leakage in the Roseton area, a Bypass Tunnel will be constructed to divert the flow around this area."

Jan 1, 2016

By Frank M. Monroe, James R. Cost

The solubility of nitrogen in vanadium is determined from 275" to 575°C by measuring the height of the nitrogen internal friction peak of equilibrated V-N alloys. The proportionality constant at 275°C between the internal friction peak height (Q- 1) and the atom percent nitrogen in solution is found to be 0.095 per at. pct for nitrogen concentrations up to 0.8 at. pct. The heat of solution of the nitride in vanadium is 5500 cal per mole. The solubility of nitrogen in the Group V metals is discussed. LITTLE work has been performed on the vanadium-nitrogen terminal solid solution. Hahn1 found the solubility for nitrogen to be very small and reported the existence of a hexagonal phase of composition near that of V2N at the solubility limit. Rostoker and Yamarnoto2 reported the solubility to be at least 3.5 at. pct at the melting point and to be less than this value at 900°C. In addition, they reported from X-ray diffraction studies that nitrogen in solution produces tetragonality in the vanadium lattice. An X-ray study by Schonberg3 has confirmed the results of Hahn but indicated that the tetragonality observed by Rostoker and Yamamoto was due to the presence of oxygen in their specimens. Beatty4 has performed lattice parameter and hardness measurements on terminal solid solutions and found the upper limit of the solubility to be at least 0.66 at. pct N. No measurements have been made of the pressure-temperature-composition relationships (P-T-X) for the terminal solid solution. As a part of a research program on gas-metal equilibrium, an attempt was made to study the P-T-X relationships in the V-N system using both the internal friction and the gas equilibration methods which have been successful with the Nb(Cb)-N and Ta-N systems (see Ref. 5 for a review of this work). Extensive investigation, using the gas equilibration methods, showed this method not to be applicable with vanadium This was presumably due to the gettering action of vanadium sublimed on the walls of the Sieverts apparatus. Thus, the nitrogen pressure relationships with temperature and composition were not obtained. The internal friction methods were, however, found to be applicable, and the temperature-composition relationships are reported in this paper and compared with similar results for the Nb-N6 and Ta-N7 systems. The existence of a Snoek internal friction peak due to nitrogen in solution in vanadium has been clearly demonstrated. 8-10 Powers and Doyle found the peak to be at approximately 275°C for frequencies near 1 cps.8 In a subsequent paper10 they reported the proportionality constant at 275°C between the internal friction peak height (Q-1) and the concentration of ni- trogen in solution (in atom percent) as 0.06 per at. pct. The studies of Stanley and wert9 indicated qualitatively that the height of the Snoek peak decreased with aging at the peak temperature and thus suggested that internal friction methods were suitable for study of the solubility. EXPERIMENTAL METHOD The vanadium for this investigation was of particularly high purity. It was obtained from the Ames Laboratory of the U.S. Atomic Energy Commission, Ames, Iowa in the form of a 1/2-in. diam, three pass zone-refined ingot. The electrical resistivity ratio (p300ºk/p4ºk) was 160. The initial composition was determined as follows: Carbon 200 ppm Oxygen 150 ppm Chromium <50 pprn Iron 125 ppm Silicon <50 ppm Other metallic 100 pprn The initial vanadium ingot was fabricated to 30-mil wire by swaging and wire drawing without the need of intermediate annealing. Lengths of this wire were then further purified (particularly for oxygen) by outgassing at 10-6 torr at 1400°C for 4 hr. The outgassing treatment resulted in specimens with a bamboo grain structure and a lustrous appearance. Desired amounts of nitrogen were added to the outgassed wires in a Sieverts apparatus in which known amounts of nitrogen were equilibrated with the wire at 1300°C. Nitrogen concentrations were produced in the desired range from less than 1 to 10 at. pct N. Monitoring of the partial pressure of nitrogen in the Sieverts apparatus indicated that at 1300°C equilibrium between the nitrogen gas and the vanadium was obtained within 10 min. Relatively rapid cooling from the nitrogen addition temperature was obtained simply by turning off the specimen heating current and cooling to room temperature in the partial pressure of nitrogen. Internal friction measurements of wire specimens were made under forepump vacuum in a torsional pendulum at frequencies near 1 cps. The torsional pendulum was of low thermal inertia and was designed so that specimens could be heated both by a conventional tube furnace and by the joule heating of a separate current through the wire specimen." Use of a static atmosphere of helium gas as a quenching medium made it possible to cut the specimen current, rapidly cool the specimen to the measurement temperature, and make a measurement of the internal friction in less than 1 min. Because of the large solubility of vanadium for nitrogen, the internal friction peak heights were in some cases greater than Q-1 = 0.1. This high damping resulted in an estimated relative uncertainty in the damping measurements of approximately 10 pct. X-ray analyses made to identify the precipitated ni-

Jan 1, 1970

By Reynold Q. Shotts

One often sees in the papers, in these days of ecological consciousness, estimates of the quantity of land that has been "devasted," "ruined," or "destroyed," by surface or strip mining, especially for coal. One feels sure that coal miners must have been the first to discover the art of excavation and that the public didn&apos;t know of its existance until five or 10 years ago! Estimates of the acreage vary widely with most of them sounding somewhat unreal. One estimate of 175,000 acres in Alabama appeared in one newspaper article and the implication was that all of this was mining for coal. The question was raised anew last summer when the author began working on a land use estimate utilizing aerial photographs, a preliminary project to the Alabama Earth Resources Technology Satellite (ERTS) contract presently being fulfilled. One land use category was barren or waste land and aside from some sand beaches in the two coastal counties in Alabama, recently strip mined land constituted most of that category. It quickly became apparent that old stripping was very hard to detect so that estimates from aerial photographs are not accurate. With regard to relatively new stripping, a thin veneer of reflective dirt washed over the countryside may result in a considerable overestimate of the excavated area. Actually, there is a way to estimate the area excavated by strip mining using published Bureau of Mines figures. At least three sets of data are needed: (1) Coal production figures, (2) average thickness of coalbeds mined, and (3) an accurate recovery figure.

Jan 1, 1973

By G. T. Krempasky

In an attempt to develop a suitable precast concrete support for underground use, two different models (1955 and 1958) of a five-piece concrete set were designed, fabricated, and tested under adverse loading conditions. Model 1955 was designed to withstand an ultimate, uniformly distributed, vertical load equivalent to what a three-piece, 12- by 12-inch wood set of intermediate-grade Douglas fir would withstand. A design figure of 138,000 pounds for the vertical load was used on both the 1955 and 1958 models. In addition, the 1958 model was designed to withstand a uniform horizontal load of 7,000 pounds per foot and additional concentrated-point loading. The step- by-step design of each model is presented in the appendixes. A series of five destruction tests was conducted underground on the 1955 model, and results of the tests showed that the type and method of blocking were of major significance.

Jan 1, 1963

By Denir Paganini Nascimento

O efeito da convecção forçada foi estudado na micro e macroestrutura de lingotes de silício grau metalúrgico obtidos pela solidificação unidirecional a partir da extração de calor por uma base refrigerada em contato com o fundo do cadinho com o banho líquido. Um disco sob rotação foi imerso no silício líquido para promover a convecção forçada. Em lingotes de 100 mm, esta convecção aumenta de 8 para 80 mm o comprimento de uma região de grãos colunares claramente alinhados e livre de intermetálicos, indicando um aumento da macrossegregação. Um modelo de transferência de calor e massa indica que o aumento de transporte de soluto causado pela convecção forçada diminui o super-resfriamento constitucional e, consequentemente, aumenta a estabilidade da interface sólido-líquido plana, sem células ou dendritas. A ausência de células e dendritas pode ter contribuído para a maior macrossegregação de impurezas observada sob efeito de convecção forçada.

Oct 30, 2017

By Edney Amaral Moraes

Os aços bifásicos são fortemente dependentes da microestrutura obtida para atender às necessidades na sua aplicação e as propriedades mecânicas requeridas. O processo de recozimento contínuo intercrítico afeta diretamente a formação microestrutural e por consequência as propriedades mecânicas. Nesse trabalho avaliou-se a influência das temperaturas de encharque intercrítico e de fim de resfriamento lento na microestrutura e nas propriedades mecânicas de um aço laminado a frio e revestido da classe de 980 MPa a partir de simulação via simulador termomecânico Gleeble. Análises via microscopia eletrônica de varredura revelaram aumento da fração de segundo constituinte com o aumento da temperatura de encharque, fato associado à formação de maiores frações de austenita durante recozimento intercrítico, refletindo no aumento do limite de escoamento e limite de resistência. A microestrutura e as propriedades mecânicas não apresentaram alteração com a variação da temperatura de fim de resfriamento lento.

Aug 16, 2017

By Francisco Diego Araruna da Silva

necessidade de elevados patamares de competitividade na indústria do aço tem levado à utilização cada vez mais frequente, por parte daqueles que utilizam lingotamento contínuo, de ferramentas de modelagem matemática da solidificação. A construção dessas ferramentas, por sua vez, possui uma etapa importante de validação, onde devem ser comparados os resultados simulados com dados reais do processo sendo estudado. Dessa forma, o presente trabalho tem como objetivo utilizar critérios metalúrgicos de qualidade e processo no lingotamento contínuo para auxiliar na construção e validação de um modelo matemático da solidificação de tarugos de aço. Uma vez que há na literatura diversas formulações para os coeficientes de transferência de calor na refrigeração primária (molde) e secundária (zona de sprays), foram realizadas análises – a luz dos critérios metalúrgicos – dos resultados simulados com nove combinações dessas formulações, sendo possível, ao final, determinar qual combinação melhor modela o processo (ou máquina) em estudo.

Aug 17, 2017

By A. An. Mushketov, A. Al. Mushketov, N. A. Sopina

"INTRIDUCTION At present, more and more metallized raw materials with a metallization degree of not less than 80% are used in the smelting of steel. The main quantity of this raw material is produced in furnaces of mine type. Advantages of this type of raw materials for metallurgical processing are low levels of harmful and slag-forming impurities and a high content of metallic iron. At the same time, the cost of smelting raw materials and obtaining high-quality steels are reduced. In addition to the undoubted merits of metallized raw materials, there are high requirements for the quality of iron concentrates, which are the starting material for metallization: the mass fraction of acidic oxides should not exceed 3%; The mass fraction of iron should not be less than 69%, mass fractions of harmful impurities (phosphorus, arsenic, sulfur, copper, etc.) should not exceed 0.02%. These requirements are dictated by the fact that the recovery of burned pellets is carried out by gas in a solid phase. In this case, the empty rock and harmful impurities from the metal are not separated and sent to the steelmaking unit, increasing the heat consumption for heating and worsening the quality of the steel. The combined production of high-quality concentrate and metallized raw materials requires a large capital outlay from the enterprise, which in the future can be compensated for by increased profit from the sale of more expensive marketable products. At present, in the territory of Russia and the CIS countries Lebedinsky mining-and-processing integrated works is the only enterprise that carries out the entire chain of operations for the production of metallized raw materials, starting with the production of high-quality magnetite concentrate with a mass fraction of iron of 69.5% and ending with the production of a metallized product in the form of hot briquetted gland. JSC «SSGPO» is the largest iron-processing enterprise in Kazakhstan, which processes about 40 million tons of ore per year and receives 16 million tons of concentrate per year with a mass fraction of iron 66.0-66.5%. The technological scheme existing at the concentrator of JSC ""SSGPO"" includes the crushing of the feed ore to the size of 20-0 mm; dry magnetic separation operation; three reduction stages to a fineness of 90-95% kl-0.071 mm; operation of desliming, wet magnetic separation and filtration of the concentrate. Dry magnetic separation of the feed ore makes it possible to remove from the process of 19.6% of the tailings with a mass fraction of the total iron 12.5%, of magnetite 2.2%. The first reduction stage is carried out in rod mills with the volume of 40 m3 to a size of -1.6 + 0.0 mm. The first stage of wet magnetic separation is carried out in counterflow magnetic separators PBM-P-150/200L. The magnetic product of the first stage of WMS is classified in hydrocyclones; sands enter the second reduction stage into central discharge ball mill 3600 × 5000. Runoff of mills enter on the second enrichment stage in counterflow magnetic separators PBM-P-150/200L. The magnetic product enters the classification of the second stage, forming a closed cycle. Mass fraction of the class -0.071 + 0 mm in classifications runoff of the second stage is 70-75%. The second stage classifications runoff is transported toWMS-III operation in semi-counter separators PBM-PP-120/300. The magnetic product of the third stage enters the classification of the third stage. Granular residue are transported to the reduction of the third stage into central discharge ball mill 3600 × 5000. The mill runoff enters the third stage of classification, forming a closed cycle. Classifications runoff of the third stage enters on deslimation. Deslimed product is sent for fine screening to the crasher «Derrick» 2SG48-60W-5STK with a cell size of 0.1 mm. Top size of crasher is sent to regrinding. Undersize with a mass fraction of the class -0.071 + 0 mm 90-95% is fed to the wet magnetic separation of WMS-"

Jan 1, 2018

By Afranio Marcio Costa

No lingotamento contínuo a busca pelo aumento de produtividade tem sido realizada com sequências longas, ou seja, várias corridas e muitas vezes com aços de diferentes composições químicas. Isso resulta na geração de placas de mistura e vários trabalhos buscam entender este processo. Este estudo tem como objetivo validar o modelo matemático de mistura existe no lingotamento da Gerdau Ouro Branco para garantir a correta aplicação da região de mistura, visando atender às especificações dos produtos, norma ASTM A36. Os resultados encontrados nas placas amostradas confirmaram a eficiência do modelo para estimar a zona de mistura. Além disso, para garantir a aplicação dessas placas na norma estudada foi utilizado o modelo de previsibilidade de propriedades mecânicas existente na laminação de chapas grossas. Finalmente, os resultados reais de composição química, limite de escoamento e resistência encontrados nas chapas avaliadas confirmaram as previsões dos modelos e atenderam às especificações do aço.

Oct 30, 2017

By Bruno Deves Flores

O presente estudo visou avaliar em escala laboratorial os efeitos da substituição de carvão importado por nacional em misturas típicas para fabricação de coque metalúrgico. Carvão da camada Barro Branco foi amostrado, beneficiado e caracterizado. Misturas entre carvões coqueificáveis importados, coque de petróleo e o carvão brasileiro foram produzidas de modo a permitir a avaliação da influência do carvão nacional na qualidade do coque. O coque gerado no estudo foi produzido em escala de laboratório e posteriormente avaliado a partir de testes de resistência mecânica e reatividade. Os resultados do estudo apontam que a substituição parcial de carvão importado por nacional é viável tecnicamente sem que ocorram prejuízos importantes à qualidade do coque gerado. As diferenças de qualidade dos coques produzidos com ou sem carvão nacional foram menores para misturas com alto teor de inertes, onde as características termoplásticas da mistura passam a controlar a qualidade do coque gerado.

Oct 30, 2017

Chile, which hosts around 30 per cent of the worldÆs copper resources, is now the largest producer and exporter of copper. Chilean copper output accounts for more than one-quarter of total worldwide production. An increase to around 40 per cent is forecast by the end of the century. In addition, Chile ranks eighth in silver production and 11th in gold output. In Chile, mining generates more than eight per cent of the countryÆs GDP and the total value of mineral exports is more than US $7.85 billion corresponding to more than 25 per cent of South AmericaÆs mineral production. The rate of growth of Chilean mineral production is indeed impressive. Table 1 shows that in the period 1969 - 1998, copper annual production increased 564 per cent from 667 000 t to 3 764 000 t. Gold production went up 27 times from 1827 to 49 770 kg. Silver output grew 1219 per cent from 95 650 kg produced in 1969 to 1 166 380 kg in 1998. Several facts explain this dramatic increase of production, but the most important was the success of exploration sustained over the same period. This resulted in the discovery of several world-class deposits which when developed into mines, account for much of the production increases. Therefore, this summary review shows the success of basic exploration carried out during the last 30 years in the Chilean territory. The review is based on data already published in different specialised mining books or magazines. It only includes those world-class discoveries not the lesser discoveries important at local scale. All figures were calculated using 1998 $US dollar and average estimated metal prices valid for 1999: copper $US 1653 per t ($US 0.75 per pound), gold $US 9452 per kg ($US 294 per ounce) and silver $US 177 per kg ($US 5.5 per ounce).

Jan 1, 1999

By Danilo de Castro Denúbila

Neste trabalho, foi avaliada a influência da temperatura de bobinamento após a laminação de tiras a quente em escala industrial na Usiminas, usina de Ipatinga, na microestrutura, na dureza e nas propriedades mecânicas em tração de um aço ARBL da classe de 800 MPa de limite de resistência mínimo. Verificou-se que a microestrutura, a dureza e as propriedades mecânicas em tração (limite de escoamento, de resistência e alongamento) foram pouco afetadas pela variação de temperatura de bobinamento na faixa estudada, entre 470°C e 680°C. Esse resultado está relacionado com o perfil de resfriamento aplicado no processo industrial, que gerou microestruturas formadas predominantemente por uma matriz ferrítica, com pequena quantidade de perlita e bainita. Como a temperatura de início de formação de martensita para o material estudado se encontra abaixo da menor temperatura de bobinamento aplicada, não houve formação significativa dessa fase.

Aug 16, 2017

By Song Yong Jin

The Jurassic coals at Datong are characterised by their strong, massive sandstone and conglomerate roofs which fail suddenly over large areas, crushing pillars and creating destructive windblasts, collapsed areas have exceeded 180,000m2 and windblasts have extended over one km underground and 200m on the surface and have been accompanied by subsidence troughs on the surface. Scientific analysis has researched premonitory signs of caving and the nature of windblasts leading to considerations of alternative mining methods and ways of dissipating the energy of windblasts to reduce their damage and danger.

Jan 1, 1992

By N. M. Steven, J. M. Moore, J. L. Kuyper

Mineral exploration and research has led to the identification of four types of tungsten mineralization in the NE-trending, Iargelyensialic, inland branch of the late Proterozoic/early Paleozoic Pan-African Damara Orogen. The mineralization (mainly scheelite) occurs in a terrane (the Central Zone) that is characterized by multiple deformation, greenschist/amphibolite-facies metamorphism and numerous peraluminous S-type granitic and pegrnatitic intrusions. The four major types of scheelite mineralization are (in ascending stratigraphic order of host rock): (1) thin (5 cm to 2 meter) quartz+plagioclase+diopside ± scapolite calc-silicate granofels with fmely disseminated scheelite (scheelite-bearing granofels; SBG) developed as discontinuous intercalations within the calc-silicate rocks of the Khan, Spes Bona, Oberwasser and Kuiseb Formations (Nosib and Swakop Groups); (2) gamet+pyroxene± vesuvianite+scheelite ± fluorite replacement skarns hosted by Okawayo, Karibib and lower Kuiseb Formation marbles in the aureoles of late tectonic, unrnineralized leucogranites; (3) metaturbidite-hosted scheelite- (and possibly wolframite-) bearing tourmalinites, both stratiform and crosscutting, in the Kuiseb Formation located in the &apos;cleavage fronts&apos; of late tectonic granitoids; (4) scheelite-bearing vesuvianite+quartz+garnet skarnoid rocks (several hundred meters in length) in the calcareous metaturbidites of the upper Kuiseb Formation. These scheelite occurrences were discovered by the follow-up of a large number of tungsten anomalies located during a regional stream sediment sampling program. Detailed mapping, ultra-violet surveys and rock sampling proved to be the most effective surface exploration techniques for locating mineralization; soil sampling and geophysics were of almost no use. The largest, continuous scheelite-bearing skarn of economic interest, Otjua, has a drill-indicated reserve of 250 000 tonnes at 0.53 wt5 WO3 and 8 wt% CaF2•

Jan 1, 1994

By Rafaela Pacheco Malvão dos Santos

O enxofre no aço é, normalmente, um residual indesejável, afetando negativamente propriedades como ductilidade tenacidade, conformabilidade, soldabilidade e resistência à corrosão. Desde os anos 1970 a prática mais comum é dessulfurar o gusa fora dos altos-fornos, evitando, sempre que possível, a dessulfuração do aço em forno panela. Isto permite vazamento de gusa com teores de enxofre mais elevados do alto-forno, reduzindo os custos de produção desde reator. Termodinamicamente, a dessulfuração do gusa é favorável, devido as condições redutoras e a interação do enxofre com o carbono. Operacionalmente, o gusa pode ser dessulfurado em carros torpedos ou em panelas de transferência, através da adição de diversos reagentes. Para controlar o processo de dessulfuração é necessário conhecer a cinética do processo. Este trabalho descreve estudos iniciais para a melhoria do modelo de controle da dessulfuração em carro torpedo na CSN através da injeção de carbureto de cálcio em pó.

Aug 16, 2017

By J. B. NEALEY

MANY nonferrous smelting plants have recently adopted natural gas as fuel with resultant economies, both in cost and efficiency of utilization. Not only has this fuel been used for roasting, reduction, sintering, drossing, and smelting, but also for power. All of the three big smelters near Salt Lake City, Utah, have been changed over from coal and oil firing to gas. Among these is the plant of the International Smelting Co., Tooele, an Anaconda subsidiary, smelters of both copper and lead ores. In the roasting division at Tooele are 32 MacDougall six-hearth roasters, each 16 ft. in diameter and 19 ft. high. Two gas burners are installed on each furnace. These burners are of the single-valve, automatic gas-air proportioning type using high-pressure gas at 10 lb.

Jan 1, 1933

By Michael E. Kelahan, Glenn A. Gruber

A review of recent phosphate beneficiation developments shows that Flotaire cells, ranging from 0.20 m to 2.44 m in diameter, have been examined in pilot scale and commercial plants. Applications of the column cells have included sized feed fractions using anionic and cationic reagent systems. In plants where the Flotaire was installed as a test unit or as an optional circuit, its use has been largely discontinued. On the other hand, when management committed to installing the Flotaire as an integral part of the flowsheet, the performance expectations were met or exceeded.

Jan 1, 1988

By Saulo Morais de Andrade

Aços de alta resistência mecânica têm sido aplicados largamente no setor automotivo para redução do peso veicular e aumento da segurança. O aço de alta resistência e baixa liga (ARBL) é um dos exemplos de materiais utilizados em peças estruturais e de reforço dos automóveis. Nesse trabalho foi avaliado o efeito das temperaturas de bobinamento e encharque nas propriedades mecânicas do aço ARBL laminado a frio microligado ao nióbio, com limite de escoamento mínimo de 410 MPa, produzido em escala industrial. De uma forma geral, foram observados queda nos limites de escoamento e resistência, e aumento do alongamento total do aço com a elevação das temperaturas avaliadas. Foi observado que a temperatura de encharque apresentou uma maior influência, ocasionando uma maior queda na resistência mecânica. Como não foram verificadas alterações significativas no tamanho de grão ferrítico, as variações nos valores de propriedades mecânicas podem ser atribuídas ao coalescimento de precipitados.

Aug 16, 2017

By Su-Ping Peng

Three dimensional (3D) seismic exploration has been carried out since the 1980s in the mining district of China, where it has been playing an indispensable role in the high yield and efficiency of coal mining. Unlike oil exploration, this technique uses high density seismic acquisition technology. In recent years, it has focused on wide azimuth 3D seismic acquisition. Evaluation of geometry moved away from depending on folds, azimuth and offset, toward being based upon a focus-ray beam. Conventionally, coalfield 3D seismic interpretation focused on time domain and was based on kinematics information, which is only suitable for less complex geological conditions. To achieve high-resolution processing for the complex topography and structure in coalfields, data processing shifted from poststack to prestack. The means to improve the accuracy of interpretation for complex geological conditions are 1) integration of multiple attributes and multiple disciplines, 2) combination of seismic and geological data, and 3) comprehensive combination of time domain and depth domain data. With the demand for lithological exploration, high-resolution data processing must also take into account the requirements of preserving amplitude in seismic data. Seismic attributes technology, seismic inversion technology, and dynamic tracking interpretation are key techniques in 3D seismic exploration. They greatly improve interpretation accuracy, produce better results in the goaf space description of the coal-bearing strata and coal seam structure, and effectively reduce exploration costs under complicated geological conditions. Therefore, these techniques will be the primary means employed in the future to deal with coalfield complex structure and lithological exploration.

Aug 1, 2013

By Vittorio Manassero, Antonello de Risi, Filippo Cavuoto

"This paper deals with an innovative mechanized method to bore and simultaneously line circular shafts, adopted in the Naples Metro project for the installation of 10 vertical shafts for ventilation purposes. With this method, excavation of shafts is carried out under a positive head of stabilizing fluid by a milling machine, temporarily set at the bottom of a permanent lining made of precast reinforced concrete segment rings. The debris is evacuated by inverse fluid circulation. The shafts in Naples are 4.5 m I.D., from 34 to 44 m deep and they are all located downtown in a highly urbanized area. They were bored and installed into volcanic soils under a hydrostatic head of up to 30 m. Displacements and groundwater level were constantly monitored to keep control of the effects on the surrounding buildings and utilities. INTRODUCTIONThe extension of Metro Line 1 in Naples (Italy) from the previous terminal of Piazza Dante to Piazza Garibaldi is also called the “low stretch”. Most of it runs along the coastline, encompassing the historical city center, the Greek-Roman Neapolis. The Metro Line crosses under densely urbanized areas for the whole way (Figure 1). It runs beneath Via Toledo, which follows the layout of the ancient Aragonese walls. The first station (Toledo) is located halfway along this street. Then, after a wide bend, the line reaches Piazza Municipio, where the second station is located. From there, the line moves along the axis of Via Depretis and Corso Umberto I, where the stations Università and Duomo are situated. The fifth station is in Piazza Garibaldi and the end of the stretch is located at the Naples Business Center. The twin single track tunnels were bored into volcanic tuff by TBM. This design choice simplified by far the construction of the tunnels and reduced to practically zero the interactions between tunnelling and surface buildings and utilities. Nevertheless, this choice entailed that the line had to be located at depths to the order of 35-45m below ground level and 30-35m below the water table. At each tunnel segment between stations, a pair of ventilation chambers were constructed (10 in total). Each ventilation chamber is connected to one TBM tunnel by a vertical shaft and a horizontal drift at the base of the shaft. The shafts, in addition to tunnel ventilation, provide a safety access/escape."

Jan 1, 2016