Search Documents

By R E. Otterness, M S. Stagg

The U. S. Bureau of Mines conducted 22 full-scale blasts to determine the effects of delay and explosive type on fragmentation. The shots were conducted over a period of 7 years in three limestone quarries and one granite quarry. Hole diameters, bench heights, and number of holes varied from 6.4- to 14-cm, 6.7- to 14-m, and 4- to 24-holes, respectively. Explosive performance and actual firing times were measured and screening was used to assess the fragmentation.

Jan 1, 1995

By X. Q. Cao

As the second largest phosphate resource in the world, Chinese phosphate ores generally grades with low of P2O5. The presentation of beneficiation test on the low grade of phosphate rock in this paper may be used for a reference for development and utilization of the similar reserves. The ore is a marine sedimentary phosphate rock containing low grade of P2O5 and high content of MgO and R2O3; The banded structure shows its suitability for heavy medium separation. The laboratory heavy liquid testing results indicate that as specific gravity of the heavy liquid is 2.85 g/cm3, a rougher concentrate assaying 28.71% P2O5 could be obtained while the rougher tailings contain only 4.47% P2O5. When the combined process with heavy liquid separation followed by direct & re-verse flotation is employed to treat the feed containing 21.15% P2O5, 3.79% MgO, 1.86% Fe2O3, 3.66% Al2O3, 23.75% A.I, and specific gravity of heavy liquid is 2.84 g/cm3, the optimum mesh of grind is 67.5% minus 200 mesh, a phosphate concentrate contained 32.51% P2O5, 0.48% MgO, 0.81% Fe2O3, 1.69% Al2O3 can be produced at a yield of 55.24%. The concentrate P2O5 recovery is 85% with which quality comply with the Class A specifications for production of phosphate fertilizer.

Jan 1, 2014

By Elmars Ence, Harold Margolin

The titanium-aluminum system has been investigated in the composition region 0 to 34 pct Al in the temperature range 800" to 1450°C. The phases encountered in this region were: a,ß, TiAl3, The reactions observed are as follows: 13 ; L - 6T. A1, 0 (15 pct Al) + 6 (18 pct Al) - yTi Al (16.5 pct Al) at -1170°C andP (7 pctpct Al) + y (9.2 pet Al) - ah(9 pct Al) at - 1060°C. A eutectoid reaction: y — a +d belm 700°C is postulated. THE Ti-A1 system has been the sub.ect of a number of investigations. Several of these1-3 have indicated extensive solubility of A1 in both a and ß titanium. Ence and Margolin, as a result of work on the Ti-A1-0 system:'5 have shown that the a solubility ofalumi-num is considerably restricted, and found that a compound, Ti2A1 existed in the region formerly designated as Q a This structure was identified as hexagonal with c/a = 0.803. Pietrokowsky confirmed the existence of this phase7 and pointed out that the structure was isomorphous with Ti3Sn.8 Although the existence of Ti,A1 has been confirmed by others,9-12 there has been considerable disagreement regarding the composition and mode of formation. A detailed reinvestigation of the Ti-A1 system has been published by Sagel et al.13 The tentative diagram indicated two phases, a, and e, occurring in the former all a region. The a, phase has the same structure as Ti2A1 and was indicated as having a broad region of solubility. Epsilon, a tetragonal phase, was shown to form within the a, solubility region. AS a result of unpublished work,14 Ence and Mugy3 olin disagreed with the interpretation of Sage1 et al., although some common features existed. The present study was conducted in an attempt to clarify prevailing uncertainties. EXPERIMENTAL PROCEDURE Alloy Preparation—Alloys were prepared from iodide titanium (99.9 pct Ti with less than 0.01 pct Zr) or Bureau of Mines electrolytic titanium (BHN-73) and high purity aluminum (99.99 pct). Alloys were arc-melted in argon or helium atmosphere as 15-g buttons in the composition range up to 34 pct Al. Depending on need, alloys were made in increments varying from 0.25 to 2 pct Al. Up to five 15-g buttons of some compositions were made. Weight losses during melting did not exceed about 1 pct of the charge and chemical analysis revealed that both titanium and aluminum were evaporated. In general, nominal and analyzed compositions agreed within 0.5 pct and therefore nominal compositions were used in plotting the data. Unavoidably, some overlap of composition occurred, particularly where small increments of A1 were used. The small increments were primarily used to obtain alloys which would fall into the narrow a -, r region and this purpose was achieved. In general, the data obtained from Bureau of Mines base titanium and iodide titanium alloys were in agreement. Forging—Both as-cast and forged samples were employed. Samples were heated for hand forging by an oxygen-hydrogen torch to the region 1200" to 1300°C. A titanium anvil and cover plate were used to prevent any iron pick-up and consequent formation of a low melting point compound. Frequent reheating kept the temperature in the desired range. Under these conditions, alloys containing up to 15.5 pct could be successfully forged. To check on the depth of contamination, forged alloys were heated slightlybelow the ß transformation temperature. Metal was removed to a depth below the contaminated surface so revealed, and the subsequent results obtained from these samples agreed closely with those secured from as-cast material. Heat Treatment—Prior to heat treatment, all alloys were vacuum annealed to remove hydrogen. Samples

Jan 1, 1962

By Jie Ma, Bo Wang, Jieyu Zhang, Jian Zhao, Zheng Chen

"In this paper, solidification process of steel ingot was simulated by ProCAST software, based on cellular automaton-finite element (CAFE) model. A 22 t steel ingot was divided into continuous small zones (100x150x180 mm) in radial direction, then the temperature field, shrinkage cavity and porosity, particularly, the microstructure were simulated. The results show that: there was a columnar-to-equiaxed transition in microstructure on radial direction. Zones, closing to the center of the ingot, had a more developed and fined equiaxed zone, while zones closing to the periphery of the ingot had a more developed columnar zone. It indicated that temperature gradient has a great influence on microstructural morphology. Thus, the simulation results were highly agree with the experimental results, verifying the feasibility of this simulation method. It significantly reduces the time of simulation, and has important significance for predicting the microstructure of large steel ingot.IntroductionSolidification microstructure of steel ingot have a significant effect on the quality of the final steel products. Although many experimental works have been carried out in order to obtain the optimum condition for solidification process of continuous casting, it is also very desirable to establish mathematical models to simulate the evolution of solidification structure. The simulation methods can be divided into deterministic models and stochastic models, which have been developed rapidly over the last couple of decades. Cellular automaton method is one of the stochastic models. Rappaz and Gandin [1, 2], Nasatac and Stefanescu [3, 4] are the earliest researchers engaged in the this field. Moreover, Rappaz and Gandin simulated the solidification structure and CET (columnar grain to equiaxed grain transition) of metals using the CAFE method (cellular automaton-finite element method) for the first time [1, 2]. Recently, the CA (cellular automaton) model also considered the effects of fluid flow on the solidification process. Zhu, et al. [5-11] improved method of CA , they used the KGT model to describe the undercooling needed during the growth of the dendrite tip."

Jan 1, 2014

By Luiz Henrique Accorsi Gans

First, this works carries an experimental evaluation for austempered ductile iron (ADI) as a gear material. And second, in order to provide a better understanding of the microstructural effect on the stress state of subsurface regions, a finite element method approach was considered using the submodeling tool in ANSYS 11.0. For this, ADI gears were produced from continuous cast iron bars, heat and thermochemical treated and tested in FZG test rig. The results were compared to those of carburized steel AISI 8620 and induction hardened steel AISI 4140 gears. The wear experiments were performed at the temperature of 90ºC with two torque stages: 135 N.m (running-in) and 302 N.m (steady-state). The time for pitting and spalling on the gears surfaces were measured using image analysis. The results showed a very good potential of using ADI for manufacturing gears, replacing induction hardened steels. Also, the ADI gear with smaller nodules showed higher life for pitting. In contact fatigue tests with severe load, the carburized AISI 8620 steel proved more adequate than the austempered ductile iron, showing that the mechanical properties are critical in the resistance to damage in gear contact. The austempered ductile iron with smaller nodule size showed to be very competitive with wear resistance similar to AISI 4140 steel induction hardened. With ANSYS, it was verified that the nodule size affects the gears life independently of the mechanical properties of the matrix. The results showed that the nodules indicate the presence of a concentration stress, but their size doesn’t affect the contact fatigue life as much as the total amount of nodules, regardless of the ductile iron microstructure. The size and number of nodules affects both the nucleation and the propagation stage of cracks. ADIs with higher amount of nodules have a greater wear resistance. Also, compared to the Hertz contact theory (isotropic material), the presence of graphite nodules indicates a non-isotropic material and made the maximum shear stress point moves toward the surface.

Jul 31, 2018

By W. C. Leslie, R. M. Fisher, K. G. Carroll

A nitride, believed to be Si3N, has been separated from three nitrided silicon steels. Germanium nitride, Ge3N4, has been prepared from pure germanium. Comparison of the diffraction patterns indicates that the two nitrides are isomorphous; on orthorhombic structure is suggested in place of the rhombohedral structure previously reported for Ge3N4. THE possibility that a nitride of silicon may, under appropriate conditions, precipitate in silicon steels or in steels killed with silicon makes it desirable to have some positive means of identifying such a compound. One such means is the X-ray or electron diffraction pattern of the nitride. A review of the meager data in the literature indicates that the nitride most likely to form is Si3N4, a conclusion supported by the results of a study of nitrided silicon steels to be published shortly by L. S. Darken and R. P. Smith, of this Laboratory. Unfortunately, there is available no diffraction pattern for this nitride. Data have been reported, however, for Ge3N4 which, judging from the similarity between germanium and silicon, might be expected to be isomorphous with Si3N4. An effort was made, therefore, to form such a silicon nitride, to determine its composition and diffraction pattern and, if possible, its structure. To this end a series of three silicon steels was nitrided under controlled conditions with the resultant formation of nitride particles which yielded an electron diffraction pattern in situ. The particles were then extracted from the steel and an attempt was made to determine their chemical composition. X-ray and electron diffraction patterns were also obtained from the extracted particles, which indicate that the nitride is isomorphous with Ge3N4, although a complete determination of the structure has not been possible. These results show that a silicon nitride with a well-defined diffraction pattern can form in silicon steels, and they suggest that this nitride is Si3N4. Materials and Procedures The sillicon steels investigated were In the form of thin sheet or strip and had the composition shown in Table I. The 0.58 and 1.21 pct Si steels were nitrided by holding them at 1110°F in an H2-NH3 atmosphere containing 3 pct ammonia for 48 hr. The nitride particle size was increased by subsequent heating at 1500°F for 13 1/2 hr in helium. The resulting microstructure is shown in Fig. 1. The steel containing 3.20 pct Si was nitrided at 1200°F for 16 1/2 hr after which it was held in helium at 1500°F for 4 hr. Its structure as seen under the electron microscope is illustrated by Fig. 2. As would be expected from the higher silicon content and the shorter holding time at 1500 °F, the nitride particles are smaller and more numerous than those in the 1.21 pct Si steel. The ammonia-hydrogen treatment reduced the carbon content of the steels to a very low level, so no interference was encountered from carbon or carbides. In the case of the 3.2 pct Si steel, the carbon was reduced to 0.003 pct before nitriding by heating in dry hydrogen. Attempts to obtain an X-ray diffraction pattern from polished and etched surfaces of the 1.21 and the 3.20 pct Si steels were unsuccessful. However, an electron diffraction pattern was obtained from the surface of the steels. The interplanar spacings obtained from these patterns arc shown in Table 11, col. 5. The nitride particles were then extracted from all three steels by dissolving the ferrite matrix in bromine-methyl acetate, the solution used in the Beeghly method for the extraction of aluminum nitride from steel. X-ray diffraction patterns of these residues, obtained by means of a spectrometer and by a 57 mm Debye-Scherrer powder camera using filtered cobalt or chromium radiation, are given in Table II along with the pattern obtained by

Jan 1, 1953

By L. Lichty, R Bhappu, R. Rowan, G. Ramadorai

Treatment of refractory gold ores containing arsenic have always presented a major problem in their processing to recover the contained precious metal values. The major difficulties are concerned with lower recoveries, production of hazardous fumes, effluents and residues. Because of'these arsenic related problems, many otherwise economically attractive precious metal deposits and dumps all over the world are not exploited. In recent years, treatment processee for refractory gold ores and concentrates have been explored and a few commercial operations employing roasting or pressure leaching have resulted. Roasting has limitations due to environmental constraints related to off gases. Pressure leaching involving high temperatures (180% to 200%) and pressures (400 psi) is accompanied by high capital and operating costs. An alternate route to roasting for treating pyrite and arsenopyrite ores and concentrates ia the "lime-oxygen hydromet" process carried out at a moderate temperature (100%) and pressure (100 psi). A simplified process for treating such arsenic containing ores and concentrates utilizing low temperature and pressure oxidation is presented. This low cost treatment with compressed air and lime renders arsenic as an inert component in the residue, meeting all the requirements of the EPA Toxicity Test. The precious metal values are then extracted from the autoclaved residue by standard cyanidation. This paper discusses this new development.

Jan 1, 1990

By William J. Douglas

Defining Productivity Productivity is a principal concern to all organizations - industrial, commercial, government, and academic. As a ratio of output to input, productivity measures the efficiency of an industrial process, much as thermodynamic efficiency measures the useful work obtained from the available energy consumed. However, there is one important difference. Whereas thermodynamic efficiency is a dimensionless a ratio of energies, productivity output and input are usually measured in different physical units. Nevertheless, the resulting ratio is a normalized expression for unit of output per unit of input to the process. In the early days of coal, mining was essentially a hand loading operation. There was little expenditure of alternative forms of energy within the process. Loading required expenditures of human energy on the order of 1.2 MJ/t (1,000 Btu per st). And if we accept the conventional value "you load 16 tons," the output to input ratio is 14.5 t (16 st) per manshift. In energy terms, it is on the order of 116 MJ/t (100,000 Btu per st) produced per labor Btu expended. However, the latter measure of efficiency was not meaningful in economic terms, while the 14.5 t (16 st) per manshift was significant. Since labor was the principal component of cost, it represented a direct relationship to the cost of production: [ ] Furthermore, when workers were paid directly on the basis of tons produced, the labor cost per ton was specified directly by this rate. With the introduction of mechanized loading, significant increases in productivity occurred, when measured on the basis of tons per manshift. Electric power consumed about 11.6-116 MJ/t (10,000-100,000 Btu per st). This makes the 29-GJ/t (25 million Btu per st) coal output/input ratio between 100 and 1,000. That is one or two orders of magnitude lower than hand loading. However, electric energy was quite inexpensive compared to labor, which made the mechanization economically efficient. The accepted productivity measure continued to be tons per manshift. This measure includes some of the effects of mechanization: namely, the additional manpower needed to maintain the machines and support the equipment that uses electrical energy. However, it does not consider the capital and operating costs that relate to mechanized equipment. As a result, the concept of tons per machine-shift has emerged as an accepted measure of shift productivity. The only appropriate measure that encorporates the productivity of men and machines is an economic one. The output is the tonnage per shift and the impact is the cost per shift. [ ] This is simply the inverse of the cost per ton. In addition, much flexibility is available in allo¬cating costs to the three categories. This adds a level of intangibility to the measure. The amount of information needed to obtain all of the required costs is appreciable compared to the simple matter of counting tons and workers. Furthermore, financial information relating to production costs is closely held by mining companies, so historical statistics on economic productivity are not publicly available. To extend the concept further, consider the value of the tonnage produced, to obtain a dimensionless ($/$) measure of economic productivity.

Jan 11, 1983

By M Chen, Q D. Gao, Y G. Hu, P Yan, W B. Lu

The safety and stability of construction structures are often affected by blast-induced waves. Investigating the generation mechanism of shear wave (S-wave) during blasting is important, because it has a strong effect in blasting damage. In this paper the generation mechanism and verification of S-wave was studied analytically and numerically. Under the finite velocity of detonation (VOD) of cylindrical charge or the compression wave (P-wave) communicating with the interface of different media during the propagation, the generation mechanism of S-wave was analysed. Propagation of blasting wave in cylindrical charge was simulated with the elastic model, and the generation of S-wave induced by finite VOD was proved. To compare with different numerical methods in simulating the generation of S-wave, the blasting process of instantaneous detonation was simulated by using the elastic model, elastic-plastic model and smoothed particle hydrodynamics and finite element method (SPH-FEM) coupled model. Results demonstrate that the S-wave could not be found in middle section of the charge if the elastic model is employed. But when using elastic-plastic model and SPH-FEM coupled model, the generation of S-wave could be verified. Under the SPH-FEM condition, the amplitude of S-wave is larger and the arrival time difference between P-wave and S-wave is closer to theoretical results.CITATION:Gao, Q D, Lu, W B, Hu, Y G, Chen, M and Yan, P, 2015. Comparison of the generation of shear wave with different simulation approaches, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 79–88 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By P. C. Thurston, T. Setterfield, D. H. Watkinson

"The Maybrun copper deposit IS In a succession of pillowed basaltic flows in the Wabigoon sub-province, northwestern Ontario. The rocks have primary flow morphologies and remarkably well-preserved crystallization textures, including quench-textured plagioclase, in spite of metamorphism to the amphibolite facies. The sulphide assemblage chalcopyrite-pyrrhotite-cubanite with minor sphalerite and pyrite is primarily in interpillow spaces and is stratabound. Basaltic rocks immediately enclosing the copper sulphide minerals have an enrichment in Fe, Mg and K and depletion in Ca and Na relative to surrounding flows. The Maybrun deposit is interpreted to have formed contemporaneously with volcanism and alteration, and was subsequently metamorphosed with the enclosing basalts.IntroductionThe association o f significant base metal accumulations with mafic submarine flows in the Archean is as yet poorly documented. Such deposits, where noted, have typically been small, and are therefore commonly over looked. The Maybrun Mine, a 2.6 x 106-tonne copper deposit in pillowed basalt, has many similarities with large, well-documented volcanogenic deposits. Given the interpretation of the Maybrun Mine to be volcanogenic in origin, there is n o reason why similar processes could not produce large deposit s. This is an important realization in an area where Archean submarine mafic rock s are very common, but frequently are examined only superficially. As gold commonly occurs in deposits such as Maybrun, even modest-sized deposits may be economic. The basalts at Maybrun are remarkable for amphibolite-facies rocks because of their extremely well-preserved delicate volcanic textures, including quench textures.The Maybrun Mine is one kilometre south of Atikwa Lake, in the Wabigoon sub-province of the Superior structural province, 75 km southeast of Kenora, northwestern Ontario, at longitude 93°35'W, latitude 49°25'N (Davies, 1973). Archean metavolcanic and metasedimentary rocks and intrusions underlie the area. Goodwin (1970) concluded that the mafic and minor felsic metavolcanic rocks, as well as the overlying metasedimentary rock s, were an eastward extension of the lower cycle of the Keewatin type section for the Lake of the Woods area. He estimated that the stratigraphic thickness of Keewatin rock s in this area is about 6900 m, of which 87% is basalt. The flows contain numerous interlayered sills, predominantly of basaltic composition; they have been extensively folded, faulted, metamorphosed to amphibolite facies and intruded by numerous felsic bodies, most importantly the Atikwa Batholith."

Jan 1, 1983

By J. A. Gay

BRITISH success in extracting significant quantities of germanium from gas works flue dusts has been one of the prime forces in promoting similar research in the United States. Pittsburgh Consolidation Coal Co. and Pennsylvania Coal & Coke Co. are two of the larger U. S. firms with germanium from flue dust research programs. British interest in germanium started in 1933 when V. M. Goldschmidt reported that some coals from the Yard Seam of Northumberland and Durham contained 30 to 50 ppm of germanium.

Jan 8, 1953

By James P. Bennett

The U.S. Bureau of Mines investigated the role of imported natural flake graphites in dolomite-carbon refractories used in steelmaking processes and evaluated carbon fibers as a potential substitute. Varying quantities (1.5-30 pct) of natural flake graphite and carbon fibers were added to test samples. The effect of the additions on modulus of rupture (75°-2,750° F), deformation under load (2,750° F), and air-slag-metal resistance (3,000° F) was studied. Carbon purity of natural flake graphite additions did not influence hot strength, deformation under load, or air-slag-metal resistance. When the quantity of 90-pct-carbon graphite addition varied between o and 30 wt pct, hot strength was highest, deformation under load lowest, and air-slag-metal wear the least at 10 wt pct. As test temperature increased from 500° to 2,750° F, the hot strength difference became less. Carbon fiber additions were limited to 1.5 pct in dolomite-carbon brick. At this level, physical properties were generally comparable to those obtained with natural flake graphite, but were below values obtained with 10-pet-f1ake graphite additions. Carbon fibers are not considered a satisfactory substitute for natural flake graphite.

Jan 1, 1989

By K. Th. Mavrommatis

Cleanness of steel is justified, measured and estimated in steelmaking process through different concepts which are mainly based on operational, empirical or semiempirical parameters and describe ?cleanness as a state?. In this work a theoretical concept is developed, considering ?cleanness as a process? and introducing a dynamic aspect into the quantification of cleanness of a steel melt, linking operational parameters with physicochemical variables, which are based on first principles. This concept and the here derived and developed variables and parameters are based on the earlier defined agglomeration index (AI) of a steel melt, the ratio of the mean inclusions diameter (MID) to the mean inter-particle distance (MIPD), which is shown to be a measure of the agglomeration tendency of the melt after deoxidation, and can serve both, to monitoring cleanness during steelmaking operation and to be useful as a basis for mathematical modelling of cleanness and of the metallurgical measures in plant, associated with production of clean steels.

Jan 1, 2006

By E. Dadzie

This paper will review some methods used to manage geotechnical risk at Damang Pit Cutback. The pit depth is designed up to 250m with push back on the eastern and western walls of the existed and depleted Railway Cutback (RCB) pit. The geotechnical design was presented by SRK Perth, focussing on the optimisation of the bench face angle which finally evolved with ?steep slope strategy?; 24m at 800 and 24m at 750 on the eastern and western walls respectively. The east wall was designed strategically to optimise the proximity of the tailings dam to the final pit crest of the push back. The pit has experienced failure in the weathered profile transgressing through the transitional material into the fresh rock at different location of the east wall since development in July 2005. To ensure stability and to minimise ore loss, the east wall has been redesigned using 700 batter angles and reduced berm width of 4m compared to 800 and 8.5 berm width of 24m bench height. The paper will also discuss how slope failures to the east wall had been sustained, managed and monitored to enhance production. Emphasis is placed on slope management at Damang which includes the principles of wall control blast, visual inspection, slope depressurisation and the state-of-the art of slope monitoring using Autoslope automated prism monitoring. Future slope monitoring is considering the use of 3D Laser and Radar to provide early warning so that evacuation could be effected. The intension is to provide mine personnel the means to identify risk areas during mining activities.

Jan 1, 2008

By R. M. Briney

A RETURN to nonwar conditions characterized the year 1946. The acquisition and forced use, under Government auspices, of low-grade and uneconomic ores, both foreign and domestic, ceased in 1945, but there was some carry-over into the early months of 1946. The world shipping situation delayed the procurement of some foreign ores, but conditions were improving by the end of the year. No actual shortage of any important alloy was experienced, hence the industry was able to make prompt shipment of orders placed. Price levels of ferroalloys, which had remained virtually constant through the war years, were forced upward, with increases on specific products as conditions necessitated. Standard ferroman-ganese and low-carbon ferrochrome were notable exceptions in that their price did not change. No new ferroalloy smelting plants were constructed. The Defense Plant Corp.. sold the works at Ashtabula, Ohio, to the Electro Metallurgical Co. A new type of ferroalloy furnace was described at the Birmingham meeting of the Electrochemical Society. Known as the "Elkem Rotary Furnace" it is distinguished by a rotating shell. The whole furnace, including shell, refrac-

Jan 1, 1947

By J. C. Reid

Computer-aided lithogeochemistry was used to "prospect" for stratabound scheelite (a tungsten ore) that occurs in many Precambrian clastic and chemical rocks, northeastern Brazil; The district is a metallogenic province covering about 5000km2. Exploration bedrock lithogeo-chemistry was applied at regional, local, and mine scales to identify regional tungsten trends and dispersion halos associated with economic tungsten mineralization. Regional coarse-mesh sampling (Cu,Mo,W) in 25km2 cells "found" all major mines and significant prospects using objective and cost objective computer mapping of bedrock geochemical data. The method is efficient ; of the 3600km2 study area only 9% of the original area remained after the initial pass. Of this area, the geo- chemically highest ranked (4%) cells contained the mines and prospects. Similar computer-aided treatment was applied to Cu,Mo,W,F, and Be lithogeochemical data from several mining concessions and prospects with outcropping and subsurface W mineralization. At a local scale out-cropping W mineralization was recognized at a distance of 500m. Fracture zones through which hydrothermal solutions traveled were identified; these were related to W mineralization at a depth of 200m.

Jan 1, 1986

By R. L. Russell

Production at Freeport Indonesia's Ertsberg open pit copper/gold mine started in 1972 at a rate of 7500 t/d. Mill throughput remained at that rate for a number of years until the discovery of the Ertsberg East (GBT) orebody. This discovery prompted three successive expansion stages from 1981 to 1988 that boosted production to 20,000 t/d. The discovery of the huge Grasberg porphyry copper deposit in 1988 launched a new era of much larger expansions. The first of these involved installation of a fourth primary mill in 1989 to bring production up to 32,000 t/d and was immediately followed by an expansion of the crushing and screening plant and the addition of a new south concentrator to bring production to 57,000 t/d in 1991. The addition of a primary ball mill and the changeout of the original Denver flotation cells in 1993 has served to optimize current production at a level of 66,000 t/d. A major expansion is now in progress. This includes construction of another new concentrator to house a SAG mill circuit and large Wemco flotation cells in an area created by the removal of 6,000,000t of glacial material. This current expansion, with a planned completion in 1995, will take production to 115,000 t/d. This paper describes the evolution of the Freeport Indonesia (FI) concentrator to-date and will then go into an in-depth discussion of the 66,000 and 115,000 t/d expansions.

Jan 1, 1994

By G. P. Pilling

The use of magnetic ore in the blast furnace is a subject of increasing importance. The end of the deposits of lake ore is in sight, although not imminent, and unless some new field is discovered, the use of magnetites will be an increasing factor in the iron production of the country. Enormous deposits of magnetic ore in the country that have been practically untouched contain ore of sufficient richness and purity to prolong materially our ore supply without extensive importation of foreign ores. Magnetic ores can be divided into three general classes: Fine un-sintered, or raw ore; raw lumpy ore; fine ore that has been sintered. Fine Unsintered Ore Typical analysis and screen test of this class of ore from the Adirondack region is as follows: Per Cent. SCREEN TeST pER Cent. Fe.................... 58.00 Remaining on 4 mesh........... 7.50 SiOz.................. 7.50 Through 4 on 8 mesh........ 13.75 Al,O,................. 1.60 8 on 10 meah........ 3.75 Baseg................. 2.77 10 on 20 mesh........ 22.50 P.................... 1.00 20 on 40 mesh........ 27.50 Mn................... 0.13 40 on 60 mesh........ 2.50 S..................... Trace 60 on 80 mesh........ 10.00 80 on 100 mesh........ 2.50 100 mesh........ 10.00 100.00

Jan 1, 1923

By G. P. Pilling

The use of magnetic ore in the blast furnace is a subject of increasing importance. The end of the deposits of lake ore is in sight, although not imminent, and unless some new field is discovered, the use of magnetites will be an increasing factor in the iron production of the country. Enormous deposits of magnetic ore in the country that have been practically untouched contain ore of sufficient richness and purity to prolong materially our ore supply without extensive importation of foreign ores. Magnetic ores can be divided into three general classes: Fine un-sintered, or raw ore; raw lumpy ore; fine ore that has been sintered. Fine Unsintered Ore Typical analysis and screen test of this class of ore from the Adirondack region is as follows: Per Cent. SCREEN TeST pER Cent. Fe.................... 58.00 Remaining on 4 mesh........... 7.50 SiOz.................. 7.50 Through 4 on 8 mesh........ 13.75 Al,O,................. 1.60 8 on 10 meah........ 3.75 Baseg................. 2.77 10 on 20 mesh........ 22.50 P.................... 1.00 20 on 40 mesh........ 27.50 Mn................... 0.13 40 on 60 mesh........ 2.50 S..................... Trace 60 on 80 mesh........ 10.00 80 on 100 mesh........ 2.50 100 mesh........ 10.00 100.00

Jan 1, 1923

By C. M. Smith

DELEGATES from 26 Local Sections and- Divisions of the Institute had three stimulating sessions during the Annual Meeting, a few topics still remaining to be discussed after the two Monday sessions.. The final session was held on Thursday morning. An abstract of the discussion will be transmitted to each delegate present. The topics included: Student relations. Section operation, membership, employment, MINING AND METALLURGY, a new nonmetallic minerals Division. licensing of engineers, and increased allotments of money to Local Sections. Some of the Sections felt that the present limit of $250 allotted to them - from the national treasury was insufficient to carry on their activities, and that this maximum should he increased. A resolution to this effect was passed for transmission to the Board of Directors.

Jan 1, 1935