Search Documents

By S. S. Cole, H. Sigurdson

The melting points of mixtures of titanium dioxide and other titanates have been reported to a limited extent as binary systems and some results have been reported in conjunction with silicon dioxide. The limited data indicated that a low melting zone might exist in a ternary or quarternary system of CaO-MgO-TiO2-Al2O3, since the eutectics reported in the binary systems of MgO.TiO2-TiO2, Al2O3TiO2-TiO2 and CaO.TiO2-TiO2 were of about equivalent composition of TiO2. The importance of a low melting region with a high titanium oxide value in the developing of high titanium slags is fully appreciated by metallurgists. A comprehensive study was undertaken to establish basic information on low melting titanate mixtures. Compounds in the System CaO-MgO-TiO2 -Al2O3 Preparation of the titanates of CaO, MgO and Al2O3 confirmed reported data that the following compounds could be formed under oxidizing conditions in solid state reactions: CaO.TiO2, 2MgO.TiO2, MgO.TiO2, MgO-2TiO2 and Al2O3.TiO2. Under oxidizing conditions it was not possible to react MgO with TiO2 in mol ratios higher than 1:2 without having unreacted TiO2 in the product, nor was it possible to form calcium or aluminum titanates with a higher mol ratio of CaO and A12O3 to TiO2 than 1:1. By fusing mixtures of Al2O3-TiO2 and MgO-2TiO2 together a series of solid solution products were obtained, which showed an MgO-2TiO2 X ray diffraction pattern shifted to smaller inter-planar spacings. Range of Investigation Data in the literature1 indicated that these titanates had melting points which ranged from 1645 to 1860°C. Since the purpose of the study was primarily to provide useful data for smelting titaniferous ores, the work was restricted to the zone of the system which would include the crystalline phases present in the slags. The explored limits were bounded by CaO.-TiO2-MgO.TiO2-TiO2in the base plane. The system was extended to a fourth component Al2O3-TiO2 since many titaniferous ores contain appreciable amounts of A12O3. In the quarternary system CaO-TiO2-MgOTiO2-TiO2-Al2O3TiO2, a tetrahedron was used to represent graphically the components, with one component at each point of the tetrahedron. In the base plane, mixtures were pre- pared to represent fairly uniform changes of composition over the desired range expressed on a mol percent basis. Al2O3-TiO2 was brought into the system in increments of 10 mol pct up to 40 pct. Mixtures were then made up for each of the Al2O3-TiO2 planes. The ranges employed were then represented by five planes cutting the tetrahedron at 10 mol pct Al2O3-TiO2 intervals. Choice of Equipment Although it was necessary for all smelting work to be done in a strongly reducing atmosphere, it was decided that all melting point determinations should be done under oxidizing conditions. This decision was prompted by the fact that TiO2 reduced to lower oxides in a reducing atmosphere with consequent changes in melting points. The use of a micropyrometer and a platinum strip furnace for work of this type is adequately described in the literature.2 With modifications, equipment was selected which provided a fairly rapid method of determining melting points of refractory oxides. The final assembly, which was used, consisted of a platinum strip furnace and a Leeds and Northrup disappearing filament optical pyrometer attached to a special telescope which magnified the sample about 20 diam. The furnace assembly consisted of a platinum strip 0.005 X 0.3 X 2.2 in. mounted on brass posts on a refractory base. This was enclosed in a black steel shell which had a 2-in. opening at the top for purposes of sighting the telescope. The platinum strip was in series with two 0.04 ohm nichrome resistors connected to the secondary of a 2 kw transformer which supplied 17 volts. The current to the primary was varied

Jan 1, 1950

By A J. Minns

This paper addresses the question: how can the minerals industry remain viable; viable in the sense that we are able to access land for exploration and discovery, we are able to develop and operate mines (and processing plants) safely and profitably and we are able to close operations in a responsible manner, so that modified landscapes are restored to acceptable community standards?Many of the answers to this question can be addressed through the theme of this conference û that of eco-efficiency. The eco-efficiency concept is very useful, since it does help to translate principles of sustainability into business value at the operational level. To provide some context to how this can be achieved, the paper discusses what is happening at the international level, outlines some key industry initiatives within Australia and then discusses what work is being done within companies.

Jan 1, 2004

By Pramod C. Thakur

Methane drainage by cross-measure boreholes on retreat longwall faces can be a viable alternative to the vertical gob degas boreholes under favorable circumstances. The research was done in a mine working Pittsburgh Coal seam in Northern West Virginia under U.S.B.M. Co-operative Agreement No. 14-09-0050-3252. The study was the first application of this technique to Pittsburgh coal seam. A total of fourteen, small diameter, inclined boreholes were drilled over a retreat longwall panel from gate roads, to intersect the overlying coal seams. All boreholes were manifolded to a pipeline and the gob gas was extracted by an exhaust fan on surface. The methane capture ratio was poor at 7 to 18% at various stages of the longwall panel. A vertical gob degas borehole captured an additional 20% gas. Poor results were due to premature failures of the cross-measure boreholes leading to air leakage. For better performance the boreholes should be drilled from a point 30 to 45 m from longwall pillar over the largest chain pillar, the standpipe should be grouted for at least 6 m, and the entry containing boreholes and the pipeline must be supported to ensure access for maintenance, and optimization of methane capture. Coursing the ventilation air around longwall such that it forces methane-migration towards cross-measure boreholes can further improve methane capture. The optimum vertical inclination is 45° ± 10°.

Jan 1, 1983

By W. R. Bruce, R. W. Wittkopp, R. L. Parratt

Introduction The Relief Canyon gold deposit is about 24 km (15 miles) east of Lovelock at the south end of the Humboldt Range in northwestern Nevada. The deposit, is in the Relief-Antelope Springs mining district, which has historically produced silver, antimony, and mercury. There is, however, no mention in the literature of commercial gold production. Fluorite prospects at the gold deposit site have had no reported production. At Relief Canyon, the Late Triassic Grass Valley formation overlies and is in fault contact with the Late Triassic Natchez Pass formation. Epithermal disseminated gold mineralization is found within the various types of fault breccia between these two formations. Geology The Natchez Pass formation of Late Middle to Late Triassic age is composed of more than 300 m (985 ft) of massive gray to dark gray locally carbonaceous dolomitic limestone. Some minor beds of shale and siltstone up to 1 m (3 ft) thick are found in the project area. The limestone is locally silty or sandy. The color of this formation below the oxidation base ranges from gray to black and appears to be a function of carbon content. The Grass Valley formation of Late Triassic age is composed of more than 200 m (655 ft) of interbedded units of thinly parted argillite, hard gray to brown quartzite, siltstone, and shale. Within the oxidation zone, these units are olive gray. A few beds within this formation are slightly calcareous and a number of sections, especially those containing shale, are dolomitic. Below the oxidation zone, the quartzite beds are often slightly carbonaceous and the argillite, siltstone, and shale beds are often highly carbonaceous, giving them a black color. Two types of intrusive rocks have been recognized at the Relief Canyon deposit. Both appear to predate mineralization. Fine to moderately fine grained quartz monzonite dikes, up to 3 m (10 ft) thick, were encountered in several drill holes. In a number of intervals, these dikes have undergone either propylitic or argillic alteration. The age of these types of dikes is not known. It appears, however, that they are either Jurassic or Cretaceous. No gold mineralization has been found in this type of dike. Diabase dikes were also encountered in a number of drill holes. These dikes have almost always been propylitically altered. Although the exact age of the diabase dikes is not known, they are probably equivalent in age to the quartz monzonite dikes. Quaternary alluvium is found forming fans at the base of steep slopes and as recent fill in present day drainages. The alluvium is composed of either Natchez Pass limestone or Grass Valley quartzite and siltstone, depending on which unit served as the bedrock source. A significant portion of the Relief Canyon deposit is covered by Quaternary alluvium. Figure 1 shows a generalized geologic map of the Relief Canyon area. At the deposit's site, the Grass Valley formation appears to have been thrust over the Natchez Pass formation. The age of the thrust is probably correlatable with the Nevadan Orogeny, which gives it a Jurassic-Cretaceous age. The general strike of the thrust, referred to as the Relief Fault, is in a northwest direction. The strike of the bedding of both the Natchez Pass and Grass Valley formations roughly parallel the strike of the Relief Fault. The general dip of both the Natchez Pass and Grass Valley formations is in a southwest direction. The general dip of the Relief Fault, in the area of the Relief Canyon gold deposit, varies and has the appearance of a northeast-southeast striking anticline that plunges in a southwest direction. A small fold perpendicular to the plunge of this anticline forms a dome over the southerly portion of the Relief Canyon deposit. A number of northeast and northwest trending normal faults slightly offset the Relief Fault. Because of their small displacement, they are not shown on the generalized map. Gold Mineralization Gold mineralization occurs along the highly brecciated fault contact between the Natchez Pass and Grass Valley formations. Weak gold mineralization often occurs up to 2 m (6.5 ft) above the thrust in the Grass Valley formation. Most of the ore grade mineralization, however, is present below the Grass

Jan 11, 1984

By Alan G. Mayton, Jon C. Volkwein

The U.S. Department of the Interior, Bureau of Mines, in cooperation with an American firm, has been contributing toward the creation of a new highwall mining system for extracting coal in active, unreclaimed contour strip mines in the United States. The prototype system features the computer-based, remote control, video operation of a thin-seam continuous miner. Haulage is accomplished remotely also with a 76-m (250-ft) long multiple-unit continuous haulage (MUCH) conveyor system on rubber-tire vehicles. One aspect of this multi-faceted effort has been to design a ventilation system for removing dust generated at the face during the extraction process. The remote mining system eliminates the need for personnel in the mined workings. Ventilation is required to remove visible dust from the area inby two video cameras. These cameras are located approximately 6 m (20 ft) from the face, one on either side of a modified Jeffrey 102HP continuous miner. Removing the dust from this area provides the remote operator with constant visual monitoring of coal extraction at the face and thus, insures the effective operation of the mining system. A ventilation system was designed for use in a mine opening with a maximum cross-sectional area of roughly 4 sq m (44 sq ft) excluding the mining machinery. This paper describes the ventilation system and discusses how it was developed in view of the constraints imposed by the mining equipment, mining conditions, and the extraction process.

Jan 1, 1989

By Francisco Sena Leite, Raquel Sobral, Vinicius Gouveia de Miranda, Céu Jesus

"The urgent need for improvements in the control and mitigation of environmental and social conditions associated with the extraction and processing of raw materials is increasingly a demand imposed by legal entities and institutions. Therefore, this present article proposes an improvement of the estimation in the magnitude of the vibrations resulting from rock blasting methodologies in the surrounding areas,incorporating the heterogeneity caused by uncontrollable parameters, such as geological andgeotechnical characteristics. This methodology combines the use of empirical vibration attenuation lawscommonly known and with terrain discretization techniques using Voronoi’s decomposition. For thevalidation assessment of this methodology, the data set collected and compiled is composed by 87 vibration measures collected in 16 sample points in one area of study of which 2/3 of the samples were used to create the model and 1/3 for the validation. Using normality tests for statistical residue analysis,it is possible to infer that this present model has null residual mean, as well as a smaller sum of residualerrors. Comparing the methodology present in this paper with the procedures executed nowadays, areduction of the errors associated with the estimation is obvious, highlighting a better characterization of the behavior of the vibrations associated with rock blasting."

Jan 1, 2017

By J. G. Dunn, A. S. Ibrado, D. J. Hollbach

Gold production is one the most important mineral process­ing industries in Western Australia. The gold is usually found in either weathered oxidised zones, or associated with sulfides. In the latter case, oxidation is achieved by some form of chemical processing, such as roasting or more recently bacterial leaching. In all cases, gold is dissolved out of the oxidised matrix by cyanide solution. Pyrrhotite is an iron sulfide generally represented by the formula Fe1_,S where O x 0.125. Three different structural forms ofpyrrhotite are known to occur naturally, stoichiometric FeS (troilite), hexagonal pyrrhotite Fe1_xS and monoclinic pyrrhotite Fe7S8 [I]. Substitution of iron atoms within the pyrrhotite structure by other ions of similar atomic radius such as nickel, copper, cobalt and manganese is also possible [2], and often observed in natural pyrrhotite samples. Pyrrhotite is abundant in Western Australian sulfide mineral deposits which are commonly associated with gold bearing ores. It is generally believed that pyrrhotite has a detrimental effect on gold recovery from such ores, as it is commonly claimed to decompose in alkaline, aerated cyanide solutions to form iron cyanide complexes, thus consuming free cyanide, and to form sulfur/oxygen containing species such as sulfate, through oxidation of sulfur in pyrrhotite, which thus consumes oxygen. From information gleaned from the literature, claims about the high reactivity of pyrrhotite in cyanide appear to be based on early cyanidation studies performed on gold ore samples which have been poorly characterised, and contained impurities such as pyrite, arsenopyrite and chalcopyrite, which may have also contributed to the levels of species observed in solution [3-5]. In addition, the investigations do not take into account that iron atoms in the pyrrhotite structure may have been partially substituted by other atoms that influence the solubility of pyrrhotite in cyanide solution.

Jan 1, 1995

By Rocky Wu

Rock bursts are one of the greatest challenges to ground control in the mining industry. With increasing mining depth and mining scale, there are more and more industry requirements on yielding rock support. Since 2008, Jennmar has been conducting large scale research and development works to develop a technically reliable and cost-effective yielding rock bolt. This paper introduces a new yielding rock support: the Yield-Lok bolt. The bolt is characterized by the designed yielding ability to produce 150?250 mm (6?10 in) of deflection at 8?10 metric tons (MT) (7.9?9.8 t) loads for every 16.4kJ (12,096 ft lb) energy input. The bolt?s performance characteristics are consistent through multiple and varying amplitude of impacts. In this paper, the design criteria of the bolt and the principle of performance are described; the dynamic testing results are discussed; and the features and application of the bolt are presented.

Jan 1, 2011

By T. E. Mccandless

Detrital minerals of mantle origin have been found in the Green River Basin of Southwestern Wyoming (Figure 1). Pyrope, pyrope-almandine, and chrome-bearing clinopyroxene and orthopyroxene occur on the antmounds of Pogonomyrmex Occidentalis. These antmounds are a common sight throughout the western U.S., and were used by early paleontologists as fossil mammal collection sites. The mound is composed of two types of material; (1) soil excavated during the digging of the nest below the surface (maximum depth 3 meters) and (2) larger grains collected from the surface and placed on the mound, probably to prevent erosion. The selection of grains to armor the mound seems to be based largely on the mean diameter of the grain, with other factors such as weight, sphericity, roundness and composition in decreasing order of importance (Wheeler and Wheeler, 1963). The minerals of this study happen to fall within that mean diameter range. The garnets are found on the mounds as 3-6 mm diameter subrounded to subangular grains. The pyroxenes are also 3-6 mm in diameter and are most commonly subangular laths. The minerals themselves show evidence of abrasion, such as frosted surfaces and rounded edges. Orange peel texture is present on some of the grains, which suggests that kelyphitic rims were once present, but have been removed. Also, no similar minerals were found in sieved soil auger samples to depths of 2 to 6 meters taken near the antmounds. These observations imply a distal rather than proximal source for the minerals. Lamproitic rocks of upper mantle origin are found bordering the "Green River Basin. The best known are the Leucite Hills, a series of ultrapotassic volcanics found on the north flank of the Rock Springs Uplift (Carmichael, 1967). Minor occurrences of mica peridotite and ultrapotassic volcanics are also found on the western end of the Uinta Mountains in Utah (Best, et al, 1968). None of these rocks are known to contain minerals like those on the antmounds. The garnets are comprised of purple chrome pyrope, red chrome pyrope-almandine, and pink to orange low chrome pyrope/pyrope-almandine. Oxide statistics for these groups are summarized in Table 1. These three groups are distinct when their Cr203 values are plotted against magnesium number (Figure 2). The chrome pyropes are highest in Cr203 (1.28-2.66%) and have high, restricted Mg number values (0.781-0.826). The chrome pyrope almandines have similarly high Cr203 (1.29-2.62%) but a lower Mg number range. The low chrome pyrope/pyrope-almandines have the lowest Cr203 content (0.09-0.73) and the widest Mg number range (0.534-0.836). Using the classification scheme of Dawson and Stephens (1975) the chrome pyropes are most similar to garnets derived from kimberlite and from garnet lherzolite, websterite, and harzburgite xenoliths in kimberlite. The chrome pyrope-almandines and the low chrome pyrope/ pyrope almandines are similar to garnets derived from eclogite nodules (Figure 3).

Jan 1, 1984

By S. Eckert, M. Reuter, D. Obiso, S. Kriebitzsch, M. Akashi

The present paper focuses the application of CFD techniques to investigate the Top-Submerged- Lance (TSL) gas injection in liquid metal. Previous works of the authors have shown that up- and down- scaling procedures based on the modified Froude number have some shortcomings, as this approach does not take into account the interfacial and viscous forces. Indeed, surface tension and dynamic viscosity of the smelting slags (σ = 0.4-0.5 N/m, μ = 0.2 Pa·s) are higher than the operating fluids that have been used in literature (water, paraffin oil) to study TSL injection in down-scaled furnaces. In order to get closer to real systems, the authors study the TSL injection of Argon in a liquid metal. An experimental campaign was carried out in the X-ray lab at Helmholtz-Zentrum Dresden-Rossendorf (HZDR), where the eutectic alloy GaInSn was used as liquid phase. The alloy is liquid at room temperature, and X-Ray imaging is used to picture the multiphase flow in a quasi-2D vessel. The aim of the present work is to demonstrate the applicability of CFD techniques to model multiphase flows involving liquid metals, and validate the model using the data produced at HZDR. The commercial software ANSYS Fluent® was used together with the Volume of Fluid model to directly resolve the gas-liquid interphase. Some features of the flow, such as the void fraction distribution and bubble detachment frequency are tracked with CFD and compared to the experimental data. INTRODUCTION In the last thirty years the TSL smelting technology has increasingly been used for industrial non- ferrous smelting processes and is now one of the significant pyrometallurgical processes. Developed in the early 1970’s at CSIRO, the furnace is nowadays commercialized in different market sectors, including copper and lead smelting, zinc fuming, waste treatment and slag recovery (Floyd, 2005). Despite the wide application of these reactors in the pyrometallurgical market, some aspects of the process are still not fully clarified, since in-situ measurements and optical accesses are prohibitive because of the high temperatures and aggressive conditions. Phenomena such as the bubbling regime, the slag solidification and the submerged combustion still need a deeper scientific investigation to obtain a better understanding of the process.

Jan 1, 2019

By Hiroyuki Matsuura, Fumitaka Tsukihashi

"Emission of CO2 gas from steelmaking industry covers more than 12 % of total CO2 emission in Japan. Though many efforts have been made to curtail energy consumption and high energy efficiency of Japanese steel production process has been achieved so far, further reduction of CO2 emission is strongly requested to develop sustainable steel production process and produce “green material”. Recently, authors have proposed the innovative hydrogen production process, in which water vapor is reacted with discharged steelmaking slag to produce hydrogen gas. This reaction can be achieved without any external energy source and operated by huge thermal energy associated with steelmaking slag and FeO or unrecovered Fe droplets that are relatively rich in the slag. In this paper, thermodynamic calculation results with various initial conditions in terms of hydrogen productivity were presented. Laboratory-scale experiments were also conducted to clarify the validity of thermodynamic calculation and the reaction rate in realistic conditions.IntroductionIronmaking and steelmaking process from iron ore through blast furnace and BOF is an essential steel production route for Japanese steel industries to supply high quality steel products in large quantity to society stably. Blast furnace – BOF process requires huge amount of fossil fuels such as mainly coal, resulting the emission of considerable amount of CO2 gas. Since the emission of CO2 gas from steel industries, about 147 Mt (FY2011), accounts for approximately 12 % of domestic CO2 gas emission in Japan (FY2011),[1] it is an urgent issue for steel industries to develop environmental-friendly ironmaking and steelmaking process and reduce CO2 emission. Various kinds of gases and by-products generated from ironmaking and steelmaking processes have been recycled as much as possible at present. Enormous thermal energy is also generated from processes and released to surrounding atmosphere as various forms such as sensible heats of gases, molten steels or by-products, and as heat losses. However, these energies are not utilized before final dissipation to atmosphere. Although various technologies to utilize thermal energy from ironmaking and steelmaking processes have been attempted to develop, practical application of these technologies has not been achieved because the thermal energy is not always useful as an energy source. In steelmaking process by BOF, fluxing agent such as CaO is added during reefing and thus about 100 kg/t-steel of steelmaking slag are generated. Since the steelmaking slag is discharged at temperature range between 1873 and 1923 K after discharge of refined molten steel, it also has large thermal energy. Amount of generated BOF slag is 11.0 Mt/y (FY2012) in Japan.[2] Assuming the amount of steelmaking slag is 10 Mt/y and its average heat capacity from room temperature to 1923 K is 1 kJ/kg·K,[3] unutilized heat is estimated to be 16 PJ/y, which is equal to annual energy consumption of 420 thousand families in Japan.[4]"

Jan 1, 2014

By J Webb

Anoxic limestone drains (ALDs) have been widely used in the passive treatment of acid mine drainage (AMD), but their effectiveness has often been less than anticipated. Iron hydroxide often precipitates around limestone particles and inhibits neutralisation. To determine the conditions under which iron hydroxide precipitates, a small-scale laboratory ALD system was built to enable a detailed examination of the chemistry of iron within the drain. For one experiment, a mixture of limestone and quartz was introduced to the drain to assist in the determination of the key mechanism governing iron precipitation. Synthetic anaerobic acid mine drainage containing Fe2+ (~130 ppm), SO4 2- and H+ was pumped at a rate of 30 mL/min up a 90 cm tall, 15 cm diameter vertical column filled with limestone gravel of 98 per cent purity. Three sampling ports were fitted at equal intervals along the column; water was periodically extracted for analysis at the sampling ports over an 11-hour period. Experiments were run at influent pH levels of 2 and 4. Results show that acid neutralisation to pH greater than 6 occurred at the inflow end of the drain. The greatest amount of iron precipitation (19.5 per cent) also occurred in this area. The lack of iron precipitation on the quartz surfaces in the quartz/limestone mixture indicates that neutralisation is the key mechanism for the precipitation of iron hydroxide on limestone particles. A pe-pH stability diagram derived for the laboratory ALD system indicates that ALDs will not be effective for AMD with pH 2. Influent waters with pH 2 require a pe of -2 (Eh: -118.4 mV) to avoid Fe precipitation upon neutralisation. Influent waters of pH 4 require a pe between -2 and -4.

Jan 1, 2003

By Laurindo De Salles Leal Filho, Arthur Pinto Chaves

The Serrana Process was developed in the 60's to concentrate an igneous low grade phosphate/carbonate ore using tall oil as a collector and corn starch as a modifier in alkaline medium. Nowadays, although tall oil has already been substituted by a new amphoteric synthetic collector, starch hasn't been substituted yet. This study is an attempt towards understanding the role played by corn starch in this specific system. By means of bench scale flotation test, it was observed that corn starch was capable of promoting the flotation of apatite, phlogopite and dolomite. No effect over calcite was observed. The best efficiency of separation apatite/gangue minerals was yielded at the concentration ranges of 17 to 20 mg/l of starch and 13 to 17 mg/l of tall oil. The starch concentration showed a strong influence over the characteristics of the froth produced by the flotation tests, mainly over the volume of the froth and its mineralization.

Jan 1, 1993

By E. C. Harder

AT a Meeting of the New York Section, on May 23, 1918, the sole subject of discussion was the nature and occurrence of iron ores in certain parts of the world.? Owing to the importance of this subject, it has been deemed' advisable to publish the remarks made at that meeting in the form of a paper, for presentation at the Milwaukee Meeting, instead of in the usual place, under News of Local Sections. The remarks related to the following districts: Brazil, by E. C. Harder, of the U. S. Geological Survey; Scandinavia, by Waldemar Lindgren, of the U. S. Geological Survey; Cuba, by C. M. Weld, of the U. S. Bureau 'of Mines; Southern Europe, by A. C. Spencer, of the U. S. Geological Survey; China, by H. Foster Bain, of the U. S. Bureau of Mines; Alsace-Lorraine, by Sidney Paige, of the U. S. Geological Survey. BRAZIL By E. C. Harder During the years immediately preceding the war, the iron ores of Brazil were attracting the attention of iron operators both in Europe and in the United States. This was clue to the large quantities of practically undeveloped ore available, and to its great purity. It is reasonably safe to state that had capital not been diverted from the exploitation of these deposits to war purposes, Brazilian iron ores would probably now be offered in European and American markets. It is certain that after the war these ores will play a prominent part in the economic reconstruction of Europe and perhaps in the development of America.

Jan 9, 1918

By Douglas G. Hubert

To put coal in its proper perspective as a source of energy for electric power production, we must first compare it to other energy sources. A report of the Atomic Industrial Forum dated February 1958 records a number of authoritative though widely varying predictions. The most optimistic of these states that by 1968 there will be a total U.S. capacity of about 6000 megawatts of nuclear power, if growth continues at the present rate. Other sources indicate over 200,000 megawatts of total electrical capacity in utility plants by 1968. This is only 3% nuclear. Therefore, 97% of our total power production will be from non-nuclear energy. Fig. 1 shows the distribution of energy sources of electric utility product- ion in the U.S. as reported by the Federal Power Commission in 1954. Note that less than one quarter of the total is hydro and about one half of the total is coal. For 1957, the Edison Electric Institute reports that of the total steam- electric generation in the U. S., 68.6% was by coal, 7.9% was by oil and 23.5% was by gas. This is an increase for coal and a decrease for oil and gas in those three years. Thus we can conclude that two-thirds of the steam-electric power in the U. S. is now generated by coal. Fig. 2 shows the major markets for coal for 1947 vs 1957. The greatest in- crease has been in the electric utility market, where it has more than doubled in the ten years. One-third of the total coal produced goes to the utilities which now represent coal?s major market. Utilities used 160 million tons of coal in 1957, and the estimated quantity for 1967 is 275 million tons, and for 1977 is 525 million tons. It is predicted that 85% of steam-electric power will be generated by coal in 1975.

Jan 1, 1959

By D. M. Metcalf

MOST PEOPLE think of peat as an inferior substitute for coal as a fuel, and will be surprised to learn that it is extensively mined in this country for use as fertilizer rather than as a fuel. Some years ago the Florida Humus Co. began producing it at Zellwood, Orange County, Fla., in a small way for local use. When, however, the company secured an Institute member, M. H. Cuise, to apply his wide experience in mining to the problems here it was found possible to decrease production costs 70 per cent and increase output tenfold. The obvious way in which to decrease costs was to replace shovel-and- horse methods with machinery, much of which, in order to keep down-invested capital, was improvised by remodeling second-hand equipment, changing the design where necessary to meet the special conditions involved.

Jan 1, 1932

Paralleling recent experiments in the U. S., the Mines Branch of the Department of Mines and Technical Surveys in Ottawa has developed a laboratory process for recovering cell-grade alumina from aluminiferous shale. Mines Branch Research Report R45 (1959) entitled The Alum-Amine Process For The Recovery of Alumina From Shale by G. Thomas and T. R. Ingraham states " . . . With the recent resurgence in Canada, and in the United States, of attempts to recover cell-grade alumina from clays and shales, the Mines Branch undertook to review certain processes that had been tried with marginal success . . . In particular, it seemed quite possible that some recent developments in organic chemistry, relating to uranium technology, might be utilized for the removal of the last traces of iron from intermediate products to permit the attainment of a satisfactory grade of alumina." This introductory paragraph explains the authors' approach toward development of an alumina recovery process from shale. The following is an abstract of their successful laboratory experiments.

Jan 3, 1960

By D. Gaboury

Most hydrothermal gold deposits contain quartz with fluid inclusions that record composition and temperature of the mineralizing event. Quartz has strong chemical and mechanical resistances to weathering and abrasion. Hence, quartz fragments occurring on weathered surfaces or in till cover have the potential to be used for gold exploration as far as we know what is the signification of the volatile content of the fluid inclusions for gold mineralization. In this perspective, fluid inclusions were analyzed in pure quartz by solid-probe mass spectrometry from gold deposits hosted in the Archean Abitibi (Canada) and Paleoproterozoic Birimian (Western Africa) belts. This approach provides the relative abundance of volatiles from families of fluid inclusions decrepitating at specific temperatures (Td). Fluids in gold deposits are aqueous-dominated with CO2 and minor H2S in accordance with their fundamental role as gold-ligands (H2S) and for pH-buffering (CO2) of the gold-bisulfide solubility. However, there is no correlation between CO2 and H2S contents of fluid inclusions with the gold grade of the samples. This suggests that trapped fluids represent a marginal portion of the fluid history recorded by the veins. However, in barren quartz veins away from known mineralization CO2 or H2S are commonly absent. Wide ranges in H2O Td from 250 to 450°C and CO2-H2O Td offsets are common, indicating phase separation. The content of other volatiles seems to be more dependent on the geological setting. Helium content may suggest proximity to a crustal-rooted fault, a critical parameter for gold mineralization. Methane and especially C2H6 appear to be indicative of fluid buffering by organic-rich material such as graphitic-shale. These rocks may provide an important primary gold reservoir from sedimentary metal-rich pyrite. Nitrogen-bearing fluids may be related to a magmatic component but can also be derived from organic-rich sedimentary rocks. For gold exploration, quartz containing CO2- H2S-bearing fluid inclusions and having H2O-CO2-Td offsets within 250 - 450°C has strong vectoring potential.

Jan 1, 2011

In 1969, Queensland Mines Limited obtained two large Prospecting Authorities in Arnhem Land, Northern Territory, Australia. The Nabarlek uranium deposit containing some 12 000 t of U308 was discovered on one of these in June 1970. Mining and stockpiling of this deposit were completed in 1979 and processing to yellowcake, which commenced in June 1980, is expected to occupy an 8-10 year period. The continuation of exploration, essential for the company to become a longer- term producer, was inhibited in 1972 by a Federal Government "freeze" on exploration in Aboriginal Reserves in the Northern Territory. Subsequently, the procedure for explorers to gain access to exploration areas in Aboriginal land was radically changed by the proclamation of the Aboriginal Land Rights (Northern Territory) Act 1976. As a result of this Act and the associated administrative policies adopted by Governments, Queensland Mines Limited has not yet regained access to the exploration areas it formally held in the early 1970's.

Jan 1, 1986

By P. C. Benedict, J. A. Titcomb

"The following description of the geology of the Northern Empire mine is recorded by the senior author, but is based on the observations and complementary mapping of both authors.The Northern Empire mine is a mile east of Beardmore, and 100 miles northeast of Port Arthur, Thunder Bay district, Ontario.Production started in March, 1934, and terminated in September, 1941. The total number of tons milled was 425,866, from which 153,103 oz. gold was recovered. The lowest level from which ore was mined was the 1,900- foot, but considerable drifting was performed on the 2,075-foot and 800 feet on the 2,415-foot, the deepest level,The vein strikes about N.72°E. and has an average dip of80°S. In stoped sections the quartz averaged about 2 feet wide. On the 1,725-foot level it was drifted on continuously for more than 7,000 feet. In the mine as a whole, practically no commercial ore was found beyond points 1,400 feet west and 1,800 feet east of the shaft. Conspicuous wall-rock alteration extended throughout this section, but not much beyond these limits. There was some splitting of the vein and widening of the alteration halo on the lower levels. The average general colour of the quartz changes with depth .The vein is in 'Keewatin' lava flows, to which it is almost conformable. It lies only a short distance south from the 'Timiskaming-Keewatin' contact ( Fig. 2). This contact is marked by a black graphitic fault. So far as is known the fault is parallel, or nearly parallel, with the flows in strike, but dips at 72°S., which is 5° flatter than the average dip of the overturned flows. A post-vein, almost flat sheet of diabase about 550 feet thick cuts outthe vein from about the 650- to the 1,200-foot level ( Figs . 1 and 3). If it was intruded along a fault, the fault had only minor displacement. A strong alteration halo extends to 200 feet above and below the diabase. The vein was conspicuous but in large part it was below ore grade for 100 feet or more above and below the diabase.-"

Jan 1, 1954