Search Documents

By R. M. Treco

THE thermal expansion of pure beryllium was first investigated by Hidnert and Sweeneyl in 1925 on a single cast specimen stated to be of 98.9 pct purity. A study of the coefficients of expansion by X-ray methods has recently been made by P. Gordon' on powder obtained from the Brush Beryllium Co. assaying 97 wt pct beryllium with about 2 wt pct oxygen as an impurity. The present work pertains to about the highest purity metal obtainable from the Brush Beryllium Co. This metal was in the form of lumps which were remelted and cast in a high-vacuum induction furnace. Expansion data in this paper deal with beryllium extruded into bars of rectangular cross-section 4x1/2 in. and the anisotropic expansivity of a large cast single crystal. Analysis of the cast metal after extrusion indicated a beryllium assay of 99.28 pct. Impurities were 0.170 pct Fe, 0.140 pct Al, 0.014 pct Mg, 0.086 pct Si, 0.020 pct Cu, 0.020 pct Mn, 0.007 pct Ni, 0.007 pct Ca, 0.080 pct C, 0.179 pct 0, (as BeO). Part I—Extruded Metal Thermal expansion measurements were obtained with a fused quartz-tube differential type dilatom-eter3 on specimens cut from the extruded sections in longitudinal and transverse directions. Specimens were machined to a diameter of 0.250 in. and a length of 3.000 in. One sample from each direction was vacuum annealed for 1 hr at 800°C. The dilatometer tube was placed in a vertical tube furnace having a uniform temperature zone which was twice the length of the sample. Average time for a complete thermal cycle to 500°C was 18 hr. Temperatures were observed with two chromel-alumel thermocouples attached to the sample about 1 M in. apart. The accuracy of temperature measure-ment was ± 0.25°C. An argon gas atmosphere sur-rounded the specimen to prevent oxidation of the beryllium. Samples were identified as shown in table I. Results - The original plan included measuring expansion up to 1000°C, but the first two runs on sample No. 5 showed that a permanent contraction occurred from

Jan 1, 1951

By Juan L. Yarmuch, Gonzalo Sepulveda

Medium- and short-term mine planning holds immense significance in optimizing production and resource utilization. It serves as a vital link between the long-term strategic plans and the day-to-day operational activities of a mine. In this context, a mathematical formulation is proposed to incorporate mining width constraints into the production scheduling process, aiming to maximize the net present value (NPV) of the schedule while ensuring enough room for the operation of mining equipment.

Jul 1, 2024

By Peter J. Barnard

Mitochondria play a key role in the regulation of apoptosis (cell death) and in diseases characterised by abnormal apoptotic responses such as cancer. Mitochondrial membrane permeabilisation (MMP), regulated by the mitochondrial permeability transition pore complex, is widely accepted as being central to the process of cell death. As a result there has been considerable recent interest in targeting mitochondrial cell death pathways in the development of new chemotherapeutic agents.(1) There is potential to overcome the two overriding problems in cancer chemotherapy?the common occurrence of drug-resistant tumour cells and the lack of selectivity of cancer drugs in differentiating between tumour cells and normal tissues. Significantly, carcinoma cells have an elevated mitochondrial membrane potential relative to normal cells and lipophilic cations are concentrated within mitochondria in response to mitochondrial membrane potentials. There is potential for the selective targeting to tumour cells with compounds having optimal lipophilic-hydrophilic character. Research stemming from the early 1980?s points to two distinct classes of Au(I) phosphine antitumour agents where an antimitochondrial mode of action has been implicated: (i) neutral linear two-coordinate Au(I) complexes such as triethylphosphinegold(I) chloride and the tetraacetylthioglucose gold(I) phosphine complex, Auranofin; (ii) cationic tetrahedral bis-chelated Au(I) phosphine complexes related to [Au(dppe)2]+.(2) Recently it has been reported that Auranofin, at submicromolar concentrations, induces MMP observed as mitochondrial swelling and dissipation of membrane potential.(3, 4) Both events are completely inhibited by cyclosporin-A, the specific inhibitor of MMP. The permeability changes were shown to occur at concentrations associated with the selective inhibition of mitochondrial thioredoxin reductase.(3) Auranofin is a potent and specific inhibitor of this enzyme due to Au(I) binding to the active-site selenol group.(5) The redox state of mitochondrial thiols may be critical in the control of MMP.(3) In general, swelling is stimulated by thiol blocking or oxidising agents and is prevented by thiol reducing agents.(1) Mitochondrial thioredoxin reductase may play an import role in the redox control of the permeability of mitochondrial membranes.(3) Our interest is in investigating the antitumour potential of Au(I) phosphine compounds using a number of different approaches. In recent work we have evaluated a series of hydrophilic analogs of [Au(dppe)2]+ containing pyridylphosphine ligands which have demonstrated greater tumour selectivity than the parent compound. To investigate the possible antimitochondrial mode of action we are studying the effect of [Au(dppe)2]+ and related compounds on isolated rat liver mitochondria. To assess whether the lipophiliccationic nature of the compounds determines the antitumour activity, we have synthesized a series of novel Au(I) complexes based on heterocyclic carbene rather than phosphine ligands. The similar chemistry and structural features of the two classes of complexes allow us to assess whether the phosphine ligands are essential for the antitumour properties.

Oct 1, 2003

The extremely cold weather and heavy snowstorms of January and February in northeastern Pennsylvania--with frozen mining equipment, diminished preparation and lack of railroad cars--severely hampered the production and distribution of anthracite. As a result, the previous estimates for the 2 months have been revised. On March 1, 1977, at the Porter Tunnel of the Kocher Coal Company at Tower City, Pa., an underground flash flood, which apparently broke through the wall of an adjoining abandoned shaft, swept through the mine. As of March 9, 1977, four miners were reported killed, three injured, and five trapped in the wreckage. The Kocher Coal Company began operations at the Porter Tunnel in 1968 and has had no fatalities until this current tragedy. The mine employs 20 persons on the surface and 115 miners underground, producing 750 tons of coal per day. Of the 109 underground mining operations in the anthracite region, this is the one remaining large mine that employs over 100 men.

Jan 1, 1977

By E. L. Horner

"Srnoky River Coal is capable ofprocessing 3 million tonnes per year ofrun-of-mine coal at the Smoky River Coal preparation facilities to produce 2.1 million tonnes of high quality, low volatile coking coal for export markets. Multi-seam surface and underground mining operations are scheduled to maintain raw coal feed to the plant. Two beneficiating circuits wash the coal. A heavy medium cyclone circuit cleans the plus 0.5 mm coal and a froth flotation circuit cleans the minus 0.5 mm coal. Clean coal is thermally dried, loaded into unit trains, treated for dust suppression, and transported to west coast port facilitiesf or export. Plant by-products are used as thermal fuel Jn an adjacent power station. Quality control procedures ensure efficient resource recovery for a yield of uniform specification product, at a 7% ash level. Introduction Smoky River Coal operates surface and underground mines in the Smoky River coalfield. Approximately 3 million tonnes per year (mt/ a) of run-of-mine (ROM) coal can be processed at the coal preparation plant to provide 2.1 mt/ a of clean, high quality, low volatile bituminous coking coal. Coal is processed by heavy media and froth flotation cleaning circuits and is thermally dried.Raw Coal Characteristics The characteristics of the ROM coal, both in terms of quality and size consistency, vary with intrinsic seam qualities and mining methods employed. The two seams mined (No. 4 and No. 10) show distinctly different washability characteristics. Seam No. 4 contains relatively few middlings and can be readily cleaned by dense-medium cyclones and froth flotation to give a clean coal at specification ash content. Seam No. JO is more difficult to wash, and the ash content of the clean coal is higher than No. 4 seam at the same operating conditions. However, when the upper I m is excluded from the plant feed, the remaining lower section has washability characteristics similar to No. 4 seam. Coal mined by underground means sometimes contains caprock and consequently tends to be dirtier than similar coal mined by surface means."

Jan 1, 1985

By Waghorne E. P

The State Electricity Commission of Victoria is Australia's largest single coal producer. Approximately 19 Mt of coal will be produced in 1989 from the SEC V's newest mine, Loy Yang Open Cut (LYOC), which com- menced overburden stripping operation in October 1982. When the adja- cent Loy Yang Power Station is completed in the late 1990's, LYOC will supply between 35 to 45 Mt/a, depending on power station performance and demand of coal for non-power generation uses. LYOC has been a major challenge for the SECV. It is the biggest single open pit coal mining development undertaken in Australia, with a whole of life capital cost approaching A$1 billion. The mine has supplied a very rapidly growing demand for coal from the expanding power station while developing in breadth, length and depth. Coal demand has consistently been above the figures anticipated during the initial planning because of the substantially improved performance of the 500 MW units of the Loy Yang A Power Station. The superior performance of the LYOC and power station has generated additional electrical energy during the first 5 years of power station operation compared with the initial planning targets- at almost no additional capital cost. This has been a major benefit to the SECV. LYOC will continue to present major challenges for the SECV, particularly in achieving overburden removal and coal reserve targets as development of the open cut continues to full depth over the next 15 years.

Jan 1, 1989

By Stephen P. Signer

The U.S. Bureau of Mines is developing an intelligent system for roof' control that uses both an expert system and neural networks to improve the capability of mining engineers to evaluate roof support effectiveness for ground control in coal mines. The expert system com- pares roof support capacities with the support requirements estimated to be necessary to maintain entry stability. It does this by evaluating the results of tests on various types of roof support and establishing the maximum allowable load according to anchorage capacity and yield strength of the support. After the user enters geological information (rock properties, geometry of the opening, in situ stresses, bolt pattern parameters, etc. ), the expert system compares the predicted required loading to the roof support capacity and gives the operator advice on the adequacy of the design and how improvements could be made. A good source of the real-time data necessary to allow the expert system to make decisions will come from a roof bolting machine being developed by the Bureau of Mines. Researchers have collected data from a Western coal mine on drill bit position, penetration rate thrust, torque, and rotation rate. Using this information, two neural net- works were developed to identify different types of strata and features in a mine roof such as rock type, rock compressive strength and joint characteristics. The result is a system that can assist a mining engineer with design information that can be constantly updated as mining progresses.

Jan 1, 1992

By Noel A. Genco, Edward F. McCarthy, Robert J. Piniazkiewicz

Talc, when it can be isolated as a pure mineral, has a composition of 63.36% SiO2, 31.89% MgO, and 4.75% H,O. However, as a commercial commodity less than half of all talc sold has a purity exceeding 95%. Nevertheless, impure talc products find a multitude of uses and few substitutes in many industrial applications. Minerals commonly associated with and sold together in talcose mixtures are chlorite, dolomite, mica, magnesite, and tremolite. Steatite was originally a mineralogical term applied to pure talc. Today steatite usually denotes a high-talc ceramic body used as an electrical insulator, and the talc used in such applications is known as steatitic talc. Steatitic talc generally is found in massive, high- purity form and in the past was machined directly into electrical parts, which rarely is done today. Impure varieties of massive or block talc are still commonly termed soapstone. Soft massive talc, suitable for crayon manufacture, has been referred to as French chalk. It has been common practice to discuss talc, soapstone, and pyrophyllite under the same general heading. In the case of soap- stone and talc this is natural, since many different types of platy, soft minerals exhibiting a high degree of lubricity (commonly referred to as slip) have been grouped together and called soapstone or talc. Further, there are mineralogical relationships between pyrophyllite and montmorillonite and between talc and hectorite. Thus, talc and pyrophyllite are sometimes referred to as clay minerals. When finely divided talc or pyrophyllite are combined with water in proportions to make a slurry, the end product does have the appearance of a clay-water mixture. Soapstone for utensils and ornaments was mined by prehistoric Native Americans on Santa Catalina Island, CA. In the mid- 1800s soapstone from deposits along the western foothills of the Sierra Nevada Mountains was used by white settlers as building and ornamental stone and for the linings and foundations of furnaces (Anon., 1956). Previous to 1916 the annual recorded production in California did not exceed 1.8 kt. From 1912 to 1918, however, output rose sharply when the Talc City, Western, and Silver Lake mines were put into operation. From 1916 to 1935, the state's annual output of talc was in the range of 8.2 to 18.2 kt. There was another increase in the mid-1930s, when the use of talc in wall tile grew rapidly. In California the production of talc grew to 57.2 kt in 1943. The post-war building boom helped California's production to grow to 108.9 kt in 1951. Production stood at 149.8 kt in 1968, 13 1.6 kt in 1969, 167.9 kt in 1970, and 140.7 kt in 1972. In the mid-seventies and early eighties, however, California's talc production declined to approximately 20 kt in 1992 due to reserves exhaustion and the material's tremolite content, which raised significant product liability concerns at the time. Talc mining in New York State dates from about 1878, when a Colonel Palmer and associates opened the first commercial talc mine on the Nelson Freeman farm near Talcville. In 1893 this operation was sold to International Pulp Co., which changed its name to International Talc Co. in 1944. The company was acquired by R.T. Vanderbilt Co., Inc., in 1974. A new talc operation, Gouverneur Talc Co., owned by R.T. Vanderbilt Co., began operations near Balmat, NY, in 1948. The initial capacity of the processing plant was 180 tpd (Gillingham, 1950). Subsequent expansions have increased capacity to more than 725 tpd. Talc was discovered in the area of Johnson, VT, in 1902, marking the birth of the Vermont talc industry. American Minerals Co. initiated plant operations at Johnson in 1904. MagnesiaTalc Co. opened a plant at Waterbury, VT, in 1913 (Burmeister, 1963, Trauffer, 1964) and acquired American Minerals Co. in 1923. The Waterbury mine had a long history as a producer of talc crayons. Eastern Magnesia Talc Co. was formed in 1924 by the merger of Eastern Talc Co. and Magnesia Talc Co. In 1956 Vermont Mineral Co., with a talc mine at Hammondsville, VT, was also acquired. A new plant was then built at Gassetts to produce roofing products. In order to produce high grade products for several markets, Eastern Magnesia Talc Co. began operating a modem froth flotation plant at West Windsor, VT, in 1964. The ore was provided by the Hammondsville mine. This operation, known as Windsor Minerals, Inc., continued from 1972 to 1989 as a subsidiary of Johnson and Johnson Co. In 1989 Cyprus Minerals Co. acquired Vermont Talc, Inc. and Windsor Minerals, Inc.. thus consolidating the talc mining and processing operations at Hamm, Windham, Johnson, Chester, Ludlow, West Windsor, Troy, and Reading, VT, under one ownership. As the result of Cyprus' sale of its worldwide talc assets to the RTZ Group in 1992, its US talc operations are now part of Luzenac America, Inc.

Jan 1, 1994

By James H. Russell

The Bureau of Mines, U.S. Department of the Interior, in cooperation with the Department of Energy, has attempted to increase the activity of nickel catalysts for converting synthesis gas, derived from coal, to a substitute natural gas. This report describes the effects of low-level additions of B, Ca, Ce, Co, Mn, Mo, Pd, Re, Ti, Y, Zn, and Zr on the methanation activity of Raney nickel. The methanation rate at 320° C and the resistance to poisoning by 2 ppm H2S were used to compare catalysts. The effects of the additions were small, and the experimental variances were large, necessitating the use of statistical methods to identify significant effects. Co, Ti, Y, and Zn improved the resistance to H2S poisoning, but only Co improved the methanation rate In some individual catalysts containing Ca, Mo, or Mn, both the methanation rate and resistance to H2S poisoning were improved.

Jan 1, 1980

By Jared Onyirimba, Jim Viellenave, Hal Demuth, Dale Verran, Chad Sorba, Errol Lawrence, David Bronkhorst

As outlined within the Denison Mines Corp’s (“Denison”) Pre-Feasibility Study ("PFS") completed in late 2018, additional work is required to increase confidence and reduce risk associated with the application of the In-Situ Recovery (“ISR”) mining method at the Phoenix deposit, located on the Wheeler River Uranium Project (“Wheeler River” or the “Project”) in northern Saskatchewan. The successful application of ISR in any geological environment largely hinges on three fundamental requirements, 1) permeability (of the deposit), 2) containment (of the mining solution) and 3) leachability (of the mineralization). Denison has designed several staged technical programs to progressively reduce risk associated with these requirements as the Company advances the Project toward a Feasibility Study (“FS”) and Environmental Impact Assessment (“EIA”). This paper will discuss the scope and results of certain technical programs being undertaken as the Company aims to develop the first ISR mining operation in the Athabasca Basin.

Jan 1, 2020

By S. Dixon

The Peñasquito deposit in Mexico is one of the largest grassroots precious metal discoveries to be developed in recent years Minera Peñasquito, S.A. de C.V., a wholly owned subsidiary of Goldcorp Inc. has developed the Peñasquito property to produce an average annual production of 120 kilo tonnes of lead containing 0.5 million oz gold and 30 million oz silver and 250 kilo tonnes of zinc containing 20 thousand oz gold and 1.5 million oz silver.. The Peñasquito property covers a 39,000 hectare area in the western half of the Concepción del Oro district in the northeast corner of Zacatecas State, Mexico, approximately 24°45'N latitude/101°30'W longitude. The sulfide reserves are 1,009 million tonnes containing 3.33 million tonnes of lead, 7.26 million tonnes of zinc, 16.5 million ounces of gold and 1,000 million ounces of silver. This paper describes the work to justify the installation of HPGR to process the crushed SAG mill pebbles. The SAG mill-Ball mill and Cone crusher (SABC) grinding circuit is an accepted grinding circuit to optimize power consumption relative to throughput. The installation of a HPGR to process the Cone crusher product is the next step in optimizing the power consumption relative to throughput. The concern expressed by some on not moving on this change in grinding circuit was the capital and operating cost of a HPGR. The pebbles from the SAG mill can be the more abrasive and are the harder particles of the ore. Goldcorp investigated the wear and processing costs of installing a HPGR to treat the crushed pebbles. The conclusion was the installation would be a very positive economic factor in the operation of Peñasquito. This is the first application of the use of HPGR to process crushed pebbles. Minera Peñasquito and M3 Engineering selected Polysius to provide a Polycom 2417 with twin 3,000 kW drives. A comprehensive test program at Polysius has shown for 7% higher circuit power it is possible to get approx 23% higher tonnage. This coupled with full utilization of the SAG and Ball Mill available energies and with proper control of the transfer size from the SAG to Ball mill circuit there is the potential to achieve 65,000 mtpd per line or a 30% total capacity increase. The cost of power for this increase in grinding capacity is 4.8 kWh/tonne.

Jan 1, 2010

By Floyd C. Kelly

A. HUltgren, .Söderfors, Sweden (written discussion*).—From the results obtained in his own experiments as well as those of Austin and of Grube Mr. Kelley derives a general law, expressed tentatively in the following words: "whenever two metals are brought into intimate contact at a temperature at which diffusion takes place, a comparatively rapid, or abnormal, grain growth results." It is suggested that,, in order adequately to represent the facts, this definition should he restricted by the following qualifications: a and b are the two metals, b diffusing into a. A. At the temperature in question a should exist as phase a 1 having a limited solubility for b. B. The supply of b by diffusion should be sufficient, in view of the rate of diffusion into a 1, to increase the concentration of b above the saturation value in a 1 so as to cause a new phase a2 to form. (7. The phase a2 should have a range of solubility for 6, thus rendering continued diffusion possible. D. In order that the columnar grains may be preserved in the structure the phase a2 should, of course, not suffer transformation on cooling. The phenomenon thus defined may be described as progressive transformation by diffusion. Its mechanism would appear to he as follows: Fig. 17 shows a portion of the equilibrium diagram a-b, Fig. 18 the distribution of b in solution after various periods of diffusion, Fig. 19 represents the structure in cross-section of a cylindrical rod of a at the end of heating period 3. 1. The first effect of diffusion of b into a will be to establish a concentration gradient in phase a1 (1, Fig. 18). When the saturation value for the temperature of the experiment (m, Fig. 17) is reached at the surface, nuclei of, a2 of composition n will form here, and later develop into a continuous layer. Assuming that diffusion proceeds without irregularities and that transformation at any point sets in without lag—i. e., in the moment saturation is exceeded—the transformation a1-a2 will advance inwards on a cylindrical surface concentric with the surface of the rod. The discontinuity of composition at the transformation surface in the position it happens to have at the end of the treatment (3, Fig. 18) will be preserved at room temperature, if the cooling is not particularly slow, and be recorded in the structure as a marked, smooth line, in agreement with Grube's and the author's observations. The shape of the distribution curves in Fig. 18 is also corroborated by the analyses given by Grube. 2. During diffusion, since the secondary phase a2 is always in immediate contact with the saturated part of the primary phase a1, there should be very little lag in the transformation. This means that the first a2 grains formed should grow in preference to the formation of independent nuclei; in other words, columnar growth results. It does not seem necessary to assume, with Green,' whose conception of the phenomenon

Jan 1, 1929

By Floyd C. Kelly

A. HUltgren, .Söderfors, Sweden (written discussion*).—From the results obtained in his own experiments as well as those of Austin and of Grube Mr. Kelley derives a general law, expressed tentatively in the following words: "whenever two metals are brought into intimate contact at a temperature at which diffusion takes place, a comparatively rapid, or abnormal, grain growth results." It is suggested that,, in order adequately to represent the facts, this definition should he restricted by the following qualifications: a and b are the two metals, b diffusing into a. A. At the temperature in question a should exist as phase a 1 having a limited solubility for b. B. The supply of b by diffusion should be sufficient, in view of the rate of diffusion into a 1, to increase the concentration of b above the saturation value in a 1 so as to cause a new phase a2 to form. (7. The phase a2 should have a range of solubility for 6, thus rendering continued diffusion possible. D. In order that the columnar grains may be preserved in the structure the phase a2 should, of course, not suffer transformation on cooling. The phenomenon thus defined may be described as progressive transformation by diffusion. Its mechanism would appear to he as follows: Fig. 17 shows a portion of the equilibrium diagram a-b, Fig. 18 the distribution of b in solution after various periods of diffusion, Fig. 19 represents the structure in cross-section of a cylindrical rod of a at the end of heating period 3. 1. The first effect of diffusion of b into a will be to establish a concentration gradient in phase a1 (1, Fig. 18). When the saturation value for the temperature of the experiment (m, Fig. 17) is reached at the surface, nuclei of, a2 of composition n will form here, and later develop into a continuous layer. Assuming that diffusion proceeds without irregularities and that transformation at any point sets in without lag—i. e., in the moment saturation is exceeded—the transformation a1-a2 will advance inwards on a cylindrical surface concentric with the surface of the rod. The discontinuity of composition at the transformation surface in the position it happens to have at the end of the treatment (3, Fig. 18) will be preserved at room temperature, if the cooling is not particularly slow, and be recorded in the structure as a marked, smooth line, in agreement with Grube's and the author's observations. The shape of the distribution curves in Fig. 18 is also corroborated by the analyses given by Grube. 2. During diffusion, since the secondary phase a2 is always in immediate contact with the saturated part of the primary phase a1, there should be very little lag in the transformation. This means that the first a2 grains formed should grow in preference to the formation of independent nuclei; in other words, columnar growth results. It does not seem necessary to assume, with Green,' whose conception of the phenomenon

Jan 1, 1929

By Robert J. Timkp, James D. Noll, Peter Hall, Robert Haney, Linda McWilliams

Diesel particulate matter (D PM) samples from underground metal/nonmetal mines are collected on quartz fiber filters and measured for carbon content using National Institute for Occupational Safety and Health Method 5040. If size-selective samplers are not used to collect D PM in the presence of car-bonaceous ore dust, both the ore dust and D PM will collect on the quartz filters, causing the carbon attributed to D PM to be artificially high. Because the D PM particle size is much smaller than that of mechanically generated mine dust aerosols, it can be separated from the larger mine dust aerosol by a single-stageimpacto1: The SKC D PM cassette is a single-stage impactor designed to collect only D PM aerosols in the presence of carbonaceous mine ore aerosols, which are commonly found in underground nonmetal mines. Howeve1: there is limited data on how efficiently the SKC D PM cassette can collect D PM in the presence of ore dust. In this study we investigated the ability of the SKC D PM cassette to collect D PM while segregating ore dust from the sample. We found that the SKC D PM cassette accurately collected D PM. In the presence of carbon-based ore aerosols having an average concentration of 8 mg/m3, no ore dust was detected on SKC D PM cassette filters. We did discover a problem: the surface areas of the D PM deposition SKC D PM cassettes, manufactured prior to August 2002were inconsistent. To correct this problem, SKC modified the cassette. The new cassette produced, with 99% confidence, a range of D PM deposit areas between 8.05 and 8.28 cm2, a difference of less than 3%.

By Andrzej Luszczkiewicz, Magdalena Duchnowska, KGHM Polska Miedz S. A., Witold Pawlos, Jan Drzymala, Alicja Bakalarz, Przemyslaw B. Kowalczuk

Numerous data in the literature confirm that the chemical composition and consumption of grinding media influence electrochemical properties of flotation suspension as well as effectiveness and selectivity of upgrading processes. During a milling process, attrition of grinding media is observed. Depending on the susceptibility to abrasion, the grinding media influence, to a different extent, the redox potential, pH as well as flotation efficiency. As a result, different upgradeability of sulfide minerals is observed. The paper presents laboratory scale flotation results, obtained for the copper sulfide ore from Polkowice Region of KGHM Polska Miedz S.A. in Poland ground in the presence of forged steel, highchrome iron and stainless steel as the grinding media. The investigated flotation feed contained 36 g/t (ppm) of silver and 1.86 % of copper. Several flotation tests were conducted using fixed amount of frother and a mixture of sodium ethyl and isobutyl xanthates as the collector at three different doses of 75, 100 and 125 g/t. A comparison of the obtained results confirmed that the application of grinding media with different chemical compositions influenced the electrochemical properties of the suspension and recovery of silver and copper in the final concentrate. The highest values of redox potential were observed for the stainless steel as the grinding medium. Moreover, in the presence of this type of grinding media, regardless of the collector dosage, the best silver upgrading was observed. For the forged and high-chrome iron media, the recovery of silver depended on the collector dosage. It is indicated that higher levels of the redox potential, together with smaller amount of iron released from the grinding medium, improve the flotation of the silver-bearing mineral compounds from the copper sulfide ore.

Jan 1, 2016

By Shinichi Takagawa

The deep sea hydrothermal deposits are one of the most prospecting resources, and various works to develop these mines are now underway. There are also various methods for the pre-site survey of the mines: acoustic survey, electro-magnetic survey, and others. However, as a precise method at the final survey, drilling/coring is indispensable to confirm the three-dimensional distribution and to grasp the dignity of the ores for the final decision of industrialization. This drilling/coring at the final survey is done at many points with distance of 15~25m between each point for on-land deposits. This means that 1km by 1km square area requires (1,000m/25m)2 ~ (1,000m/15m)2 = 1,600 ~ 4,500 holes. The drilling/coring depths will be around 30m or more for the hydrothermal deposits. This depth seems very shallow, but because the stratum is very brittle and is very difficult to core, the average core recovery ratio is around 50%, and 0% core recovery happens very often. Thus, the indispensable work of coring for grasping the dignity of ores is a very difficult work although the coring depth is shallow, and also the required number of holes is enormous. Conventional drilling/coring method on the ocean is to use drillship. However, the cost is very huge. Recently a new technique has come out which is to use remotely controlled drilling machine on seafloor. This machine seems to have a very good performance. However, it is reported that the available inclination of the seafloor where the machine sits on must be less than 15 degrees. The sea floor inclinations of active hydrothermal vents area are usually very steep and slopes of 45 degrees or more are prevailing and it seems very hard to carry out drilling/coring for the machine at these steep slopes, although it is impossible to mine the ore at these areas because the temperature is too high to work there. The inclination of the sea floor at the dead or paused hydrothermal vents area where ore recovery is possible may be not so steep, and the machine may work well. However, the required number of holes is still a very heavy burden. In order to solve these problems, the author proposes a new concept of drilling/coring system operated from a conventional research ship. This concept is still a desk plan, but the author wants to realize this system at any means.

Jan 1, 2011

By D. A. Hayman, N. Rambuda, N. A. Sithole, C. Hockaday, J. D. Steenkamp

"Mogale Alloys operates two alternating current (AC) submerged arc furnaces (SAFs), and two direct current (DC) open bath furnaces. These furnaces are capable of producing two products, silicomanganese (SiMn) and ferrochrome (FeCr), with a total production capacity of 110 000 t/a. This paper focuses on the silicomanganese process specific to Mogale Alloys, with a two-furnace operation facility that produces 55 000 t of SiMn per annum.IntroductionMogale Alloys is situated in Krugersdorp in the West Rand District Municipality in South Africa’s Gauteng Province. The Krugersdorp facilities were initiated by Palmiet Chrome Corporation in February 1963 to produce charge chrome (Basson, Curr, and Gericke, 2007). Mogale Alloys bought the Palmiet Chrome facilities in 2005 from Samancor Chrome. The Afarak Group currently owns 90% of Mogale Alloys.SiMn is produced in two 20 MVA submerged arc furnaces (SAFs), which were originally built for chromite processing, and ferrochromium (FeCr) in two DC open bath furnaces rated at 40 MVA and 10 MVA. When this paper was compiled, the 10 MVA furnace was not operational due to the high cost of production, and one of the 20 MVA SAFs was recently converted to produce FeCr due to market constraints. Mogale Alloys has 290 permanent employees with four contracting companies on site. The paper presented here focuses on the production of SiMn at Mogale Alloys.The high-level process flow at Mogale Alloys is summarized in Figure 1, which details the raw material input and the products produced by the two 20 MVA furnaces. SiMn is produced by carbothermic reduction of manganese-bearing raw materials from four different sources, namely Wessels, Mamatwan, and UMK ores, and BHP sinter feed. The carbon sources are bituminous coal from Forzando and Msobo, local suppliers in Mpumalanga."

Nov 1, 2018

By J. P. McGee

As part of a joint U.S. Atomic Energy Commission-Federal Bureau of Mines program for using nuclear energy to supply process heat, a simulated nuclear loop has been constructed to test components. This loop has been operated for more than 1,800 hours at 100 p.s.i.g. Of this period, 23 hours were at 2,500° F. and higher; 540 at 2,000° to 2,500° F.; 840 at 1,500° to 2,000° F.; 200 at 1,000° to 1,500° F.; and 260 below 1,000° F. Leakage at flanges and welds was not a serious problem. A helium-recycle system with gas temperatures of 2,300° to 2,500° F. and a static pressure of 250 p.s.i.g. appears feasible. Difficulties were encountered with the recycle compressor due to thermal distortion of the impeller and shaft. The use of sealed bearings limits compressor operation to the life of the bearings.

Jan 1, 1960

By C. Zhou, C. C. Jobes, J. H. DuCarme

"Magnetic proximity detection systems (PDSs) are used with continuous mining machines (CMMs) to protect miners from striking and pinning accidents. Generators are used in a PDS to create magnetic fields covering the space around a CMM. The PDS determines the proximity of a miner relative to the CMM based on the magnetic flux density detected by a miner-wearable component (MWC) and simultaneously alerts the miner and stops the motion of the CMM if the miner is within a proximity that creates a striking hazard. A stable magnetic field is essential to the accuracy of the proximity calculations performed by the PDS. This paper presents the results of a systematic study of the magnetic influence of two types of steel structures found near a CMM—the body of the CMM itself and the wire mesh used for roof and rib control. The results show that the steel of the CMM body can change the magnetic field distribution and also alter electrical parameters of a PDS by changing its generator current. The study also shows that, depending on the distance between the wire mesh and a generator, the magnetic field can also be altered. INTRODUCTION Continuous mining machines (CMMs) can be up to 10 m (33’) in length and more than 3 m (10’) in width. These machines perform the coal cutting operations in underground room-and-pillar coal mines. Accidents during CMM operation accounts for an average of 250 injuries every year, and 43 miners have been killed by striking or pinning accidents involving CMMs in the United States from 1984 to 2015.Because of these fatalities and injuries, the Mine Safety and Health Administration (MSHA) promulgated a regulation in 2015 that requires the use of proximity detection systems (PDSs) on all CMMs with the exception of full-face machines (Mine Safety and Health Administration, 2015). Currently, there are five different proximity detection systems that MSHA has approved as permissible for use in U.S. underground coal mines (Mine Safety and Health Administration, 2013). All of these PDSs rely on a miner-wearable component (MWC) to detect the generated magnetic fields that PDSs produce around a CMM (Schiffbauer, 2002). These systems use the magnetic field strength readings in terms of magnetic flux density from the MWC to determine whether a miner is at a safe distance from the CMM. A stable magnetic field is essential for the accuracy of a PDS."

Jan 1, 2018

By L. E. Djingheuzian

Introduction Cylindrical grinding mills have been used for a long time, but during many years of testing no methods were established that gave consistent results. The work by both scientific investigators and operators led very often to contradictory conclusions, and each millman was very much 'on his own' when trying to find the limits for working of his ball-mills. Fred C. Bond, in the introduction to his paper on Wear and Size Distribution of Grinding Balls, freely states that the mathematical immaturity of the grinding process "is the cause of many inefficient designs and installations as well as of much poorly oriented experimental work", and evidently he sees the solution of all our grinding problems in the discovery of the fundamental laws "which can change the empirical art into a mathematically exact science". While the writer is in complete agreement with Mr. Bond that grinding is governed by fundamental laws which can be expressed by mathematical formulae, there are so many variables in grinding, all interwoven with each other and mutually influencing each other, that the coalescing and merging of all these variables into a harmonious mathematical whole appears to be a homeric job. However, a light appeared on the horizon when it was proposed that power be used as an index of the grinding operation. It is pertinent to quote Gow, Guggenheim, Campbell, and Coghill from their paper on Ball Milling, in which they say: "Much of the past literature devoted to the subject has been concerned with the Kick-Rittinger dispute over evaluating grinding, or with dissertations on ball paths and the closely allied impact versus attrition hypotheses or with the exclusive consideration of certain specific variables, such as mill speed or circulating load, irrespectve of the other factors in operation. Such subjects may be dismissed with but little discussion in what may be called, by comparison a new philosophy in the stud of ball milling. Briefly this 'new philosophy' consists ' of using power as an index of the mill operation, and investigating grinding from the standpoint of set and induced variables with emphasis on the latter". But it is safe to assume that it was the work by E.W. Davis, H. E. T. Haultain, F. C. Dyer, A: M. Gaudin, J. Gross, S. R. Zimmerley, and others, that cleared the path for the authors of Ball Milling and induced them and A. W. Fahrenwald to look farther afield and thus to establish a far-reaching relationship between the power and capacity and the diameter of the ball-mills.

Jan 1, 1949