Search Documents

By Maria D. Salazar-Villalpando, Anthony Cugini, Bryan Reyes

"The electrochemical reduction of CO2 was performed in a laboratory-made, divided Htype cell. A copper electrode was used as the cathode. An Aldrich Nafion 117-type ion exchange membrane (0.18mm thickness) was used as the diaphragm. NaHCO3 and KHCO3 were studied as the catholytes. Hydrogen evolution from water reduction and products from CO2 electrochemical conversion were recorded. Higher CO2 reduction enhancement was observed by KHCO3 as compared to NaHCO3. The main conclusion of this work is that in fact CO2 can be electrochemically reduced with copper electrodes.1.-INTRODUCTIONThe direct electrochemical reduction of CO2 may allow for a simple process and, by avoiding high temperature reactors, would enable the process production rate to be quickly varied to follow the time of day availability of surplus electricity [1]. Temperature has a major effect on the electrochemical conversion of CO2 since its solubility increases when temperature decreases [2]. The electrical potential applied to the electrochemical reacting system will have an influence on the product distribution, as well. For example, a narrow potential range during cyclo-voltagraphic studies will determine the detection of a lower number of products. A recommended potential range to study the electrochemical reduction of CO2 is -2V to 2V. Moreover, the reaction rate on the electrode is governed by various processes, such as the kinetics of electron transfer, adsorption/desorption at the electrode surface, and diffusion of CO2 to the Cu electrode. The availability of active species, CO2 for electro-reduction, is extremely low at the vicinity of the electrode surface and it seriously interferes with the rate of mass transfer. In batch type electrolytic reactors, depletion of CO2 at the surface takes place first. CO2 from the bulk then has to diffuse to the electrode surface, resulting in mass transfer controlled kinetic phenomena. During the above process, several other competitive side reactions could suppress the primary reaction even though the cathode has good electro catalytic properties for reduction of carbon dioxide. When the dynamic supply of specific active species is ensured to electrode surface, the mass transfer effects are minimized to certain extent. Hence it is envisaged that a continuous flow reactor is more efficient for the electro-reduction of CO2 in CO2 saturated aqueous electrolytes. The primary reactions that occur at the copper electrode during the reduction of CO2 are listed below (with the standard potentials calculated using formation energies [1] :"

Jan 1, 2010

By L. S. Richardson, N. J. Grant

Iodide-grade titanium, two oxygen alloys, and two aluminum alloys were studied by means of creep-rupture tests from 1000° to 2000°F. From the test information an evaluation was made of, 1) the relative creep-rupture strengths of the u (hexagonal-close-packed) and 0 (body-centered-cubic) forms of titanium and some of its alloys; 2) the effects of solid-solution strengthening by oxygen and aluminum on the u and 0 structures; and 3) the extent and effect of atmospheric oxygen alloying on rupture life in tests above about 1000°F. THE use of titanium alloys at temperatures above 1000° F has been considered unlikely by most investigators because of low creep strength (based on a requirement for room-temperature ductility, formability, and weldability) and low oxidation resistance. The results of this testing program do not entirely uphold this pessimism in terms of strength and oxidation resistance. The observations described below are based entirely on stress-rupture results, although some creep tests were also carried out on these alloys. Three items of primary importance are covered: 1) Stress-rupture data in the form of the Larson-Miller parameter curves for several titanium alloys at temperatures up to 2000°F; 2) The relative strengths of the hexagonal-close-packed a structure and the body-centered-cubic 0 structure; 3) The effects of solid-solution alloying on the creep-rupture properties of titaniu'm at elevated temperatures. Only two investigatons have reported the creep- rupture properties of titanium at temperatures above 1000° F. Lunsford and rant' tested iodide titanium; their values are also utilized in the paper. EXPERIMENTAL PROCEDURE After a few tests had been made in a conventional creep-rupture test machine, it became clear that some sort of atmospheric protection would be necessary for short-time tests conducted at temperatures above 1600°F, or for times greater than 100 hr at 1200°F or above. Several furnace units and test machines were constructed, the most successful of which is shown in Fig. 1. Certain experimental difficulties peculiar to titanium were encountered; for example, the use of molybdenum holders was dictated because titanium forms low melting-point eutectics with conventional high-temperature alloys containing appreciable amounts of iron, nickel, or cobalt. This same difficulty made the use of chrome l-alumel thermocouples in direct contact with a test specimen impossible, above about 1500" F. The high-temperature high-vacuum furnace shown in Fig. 1 was capable of maintaining a vacuum of better than 10"5 mm of mercury at 2000°F (pressure measured in cold part of system) and 5 X lo-' mm at room temperature. Most of the tests eonducted in vacuum were at temperatures

Jan 1, 1960

By Washington Luiz Mafra

Every year the conventional direct reduction processes ? Midrex and HYL III ? increased their market share in the world steel production, even though they are only economically feasible in countries where natural gas is available at competitive prices. In this context, the new Midrex projects are based on large reactors (Megamod - 1.5 to 1.8 Mt/y of DRI), reduction temperatures of the metallic burden up to 850oC, with bustle gas temperatures between 960oC e 1050oC. Thus, the requirements of metallic burden performance, as well as the evaluating methods, usually based on ISO standards, need to be reviewed. It is well known that the standards usually applied to quality evaluation do not reflect the performance of metallic burden inside the reactors. This paper describes the different methods of evaluating the disintegration under reduction of DR pellets based on ISO 11257 standard. This is the most important method used by pellet producers and customers for evaluating DR feedstocks. The different methodologies tested to evaluate the disintegration under reduction had varying results, evidencing the relevance of the method and the quality of the pellet. Nevertheless, validating the method in an industrial reactor is still fundamental.

May 1, 2007

By R. G. Reddy

The effect of solid particles on viscosity behavior of Na2O-O-B2O3-SiO2 melts of composition XSio2/XNa2o =0.5 and in the temperature range of 900- 1150 K was studied. Samples were analyzed by X-ray diffraction and optical microscopy. The results showed that a crystalline phase (NaBO2) was formed and its amount increases with decrease in X,, from 0.50 to 0.25. The experimental viscosity values were compared with the predicted values using our viscosity model developed earlier. At low temperatures, for low content of B2O3 , the experimental values exhibits a large deviation from the predicted values. It was concluded that the deviation was due to the formation of solid particles in the molten slags. The existence of these solid particles increased the viscosity values significantly. A new viscosity model was developed to include the effect of solid particles.

Jan 1, 1993

By H. E. Powell

The magnetic susceptibilities of 34 manganese-bearing minerals were determined. The source of each sample and petrographic, spectrographic, and chemical analyses are given. Included are values for ismorphous series showing wide ranges of composition and for a few high-purity synthetic minerals.

Jan 1, 1968

By L. C. IlsLey

The Burrell methane indicator developed by Col. G. A. Burrell in 1915 was modified during 1918 to the " insulated type " Burrell indicator . Though this instrument has been used in mines since its first introduction , it was not formally approved as safe and efficient for use in gaseous mines until March , 1922. The indicator is built by the Mine Safety Appliances Co. , Pittsburgh , Pa . Approval No. 800 has been assigned to this company covering the device in the form approved . The principle of the Burrell indicator is fairly well known . It works on the same principle as the Haldane apparatus - measuring by means of a graduated scale , the contraction resulting from burning the methane content of an air and gas sample . A given aniount of the mine atmosphere to be tested for methane is taken into the indicator . This sample is then thoroughly shaken with the water in the indicator for one minute . The methane in the sample is now burned for two minutes by a heated platinum coil , which is energized by a small storage battery containing two Edison cells connected in series . After the glower or coil has burned for two minutes , it is disconnected from the battery , and the indicator is again shaken for The amount of contraction observed by reading the height the water rises in the U- tube of the indicator , which is calibrated to register the percentage of gas in the sample . The indicator as approved by the Bureau of Mines is equipped with an Edison M- 8 mine- lamp battery , and with a glass and scale graduated from zerɔ tɔ four per cent methane . The approval of a corbination service that is , an attachment for giving illumination from the same battery from which the platinum glower is operated has been withheld pending the development of a battery with larger capacity . - Under laboratory operating conditions , a single glower was capable of making at least 20 determinations if proper precautions were observed with respect to the use of freshly charged batteries . A battery should be allowed to stand off charge several hours before using in an indicator , as the peak voltage of a freshly charged Edison cell is abnormally high and is likely to send enough current through the glower to melt the platinum wire . Fifty-seven satisfactory operations were obtained from a completely charged battery . The point where the voltage of the cell fell below 2.3 volts with the glower attached was taken as the lower limit of successful operation . A voltage less than 2.3 does not permit the lower to burn at a temperature that will completely burn the gas in the air , thus giving a false indication .

Jun 1, 1922

By Fuqiang Zheng, Yufeng Guo, Guanzhou Qiu, Tao Jiang, Xiaoming Qu

MxTi3-xO5 is the main titanium-bearing mineral in the titanium-bearing electric furnace slag (TEFS), which is produced by direct reduction-electric furnace smelting process with vanadium titanomagnetite concentrate in Panzhihua-Xichang region of China. In order to effectively utilize the titanium resource in TEFS, the thermomechanical analysis and conditions for the growing up of MxTi3-xO5 grain were investigated, which emphasized on the effects of CaF2 and cooling rate on the crystallization of MxTi3-xO5 in the melting process. The mineral phase and morphology of titanium-bearing slag were determined by XRD and electron microscope technique, respectively. The results indicated that the average grain size of MxTi3-xO5 grown up from 30 to 92 lm and the area fraction of MxTi3-xO5 reached about 66% from 61% under the conditions of 5 wt% CaF2 and cooling rate at 1 °C/min.

Mar 1, 2017

By Jiangtao Li, Zhongwei Zhao, Xingyu Chen, Xuheng Liu

In tungsten ion-exchange process, excessive sodium impurity enters into ammonium tungstate solution. However, the Na content of the final ammonium paratungstate (APT) product must be strictly controlled. Consequently, it is necessary to remove Na from the ammonium tungstate solution during processing in order to obtain the required purity of APT. In this study, porous Na specific absorbent, Na1+xAlxTi2−x(PO4)3, is used to remove Na from the ammonium tungstate solution. Through experiments, the effect of reagent concentration of Na1+xAlxTi2−x(PO4)3, reaction time, reaction temperature and Na concentration on the Na removal were investigated. The results showed that under optimal reaction conditions of reagent amount of NATP 1.0 times of theoretical amount, reaction temperature 25 °C and reaction time 15 min, the Na removal from commercial (NH4)2WO4 solution can reach 98%. Na1+xAlxTi2−x(PO4)3 has a good applicability to different Na+ concentrations. The obtained APT product reaches the national standard purity of zero level.

Jan 1, 2014

By Jr. Hill

Laboratory metallurgical treatments of three high-iron bauxite ores from Arkansas were conducted to determine the relative effectiveness of experimental methods for recovering alumina and a commercially acceptable iron concentrate. The standard for evaluating recoveries from experimental processes was the Al2O3 recovery from Bayer digests of the crude ores; recoveries from digestion of the three ores were 74.1, 87.4, and 88.7 percent. Flotation, magnetic separation, or various combinations of digestion, calcination, and reduction-sintering, leaching, and magnetic separation of leach residues failed to produce Al2O3 recoveries as high as the standard. A high-iron-bearing fraction, containing between 68 and 78 percent of the total iron, was produced in a three-phase treatment involving a caustic, lime reduction-sinter of the crude ore, water extraction of Al2O3 from the sinter, and magnetic separation of the leach residue.

Jan 1, 1967

By L. H. Levenson, Charles S. Barrett

Numerous determinations1-' of the texture of cold-rolled polycrystalline iron, steel, and ferritic alloys have been made with good agreement among the various observers as to the principal features of the texture common to all, but there has been no adequate explanation of the texture in terms of, the behavior of individual grains. This study presents an explanation of the texture based on the observed rotation of single crystals when deformed in a manner similar to a grain in the aggregate, a method we have found useful in leading to a better understanding of compression and tension textures;8,9,10 in particular, the aim has been to determine experimentally the end orientations of rolled single crystals of iron. These are discussed in connection with the point of view of Weverl and of Boas and Schmid2 that the rolling texture is a simple compression texture (compression normal to the rolling plane) superimposed on a simple tension texture (tension in the rolling direction), and the point of view of Kurdjumow and Sachs3 that three ideal end orientations exist. Experimental Method The single crystals used were in the form of disks cut from a stock of crystalst pre- pared in this laboratory by a strain-anneal method from mild steel decarburized and purified in hydrogen, the details of which have been described elsewhere.11 To ensure maximum elongation in the rolling direction and to simulate approximately the rolling of a grain in an aggregate, lateral flow was constrained by placing each crystal in a close-fitting hole in a plate of copper or iron of equal thickness and rolling the plate and crystal together. About one-third of the crystals were rolled in a "sandwich" pack by adding top and bottom cover plates. The two-high mill used had 8-in. diameter rolls and was operated at 15 r.p.m. The initial diameter of the crystals was between 1/4 and 1/2 in., while the starting thickness varied from 0.031 to 0.376 in. With a single exception, which was rolled 63 per cent, the crystals were rolled to a final reduction in thickness of 82 to 97 per cent in 20 to 40 passes, alternately changing the sense of the rolling direction. The initial orientations of the crystals were determined either by X-ray back reflection12 or by optical reflectionl3 from etch pits; the mean final orientations were determined by X-ray Laue photograms using molybdenum, silver, or tungsten radiations, by optical reflection, and in many cases by both methods. Results Twenty-six crystals were studied. It was found that there were three typical be-

Jan 1, 1941

By Charles S. Barrett, L. H. Levenson

Numerous determinations1-' of the texture of cold-rolled polycrystalline iron, steel, and ferritic alloys have been made with good agreement among the various observers as to the principal features of the texture common to all, but there has been no adequate explanation of the texture in terms of, the behavior of individual grains. This study presents an explanation of the texture based on the observed rotation of single crystals when deformed in a manner similar to a grain in the aggregate, a method we have found useful in leading to a better understanding of compression and tension textures;8,9,10 in particular, the aim has been to determine experimentally the end orientations of rolled single crystals of iron. These are discussed in connection with the point of view of Weverl and of Boas and Schmid2 that the rolling texture is a simple compression texture (compression normal to the rolling plane) superimposed on a simple tension texture (tension in the rolling direction), and the point of view of Kurdjumow and Sachs3 that three ideal end orientations exist. Experimental Method The single crystals used were in the form of disks cut from a stock of crystalst pre- pared in this laboratory by a strain-anneal method from mild steel decarburized and purified in hydrogen, the details of which have been described elsewhere.11 To ensure maximum elongation in the rolling direction and to simulate approximately the rolling of a grain in an aggregate, lateral flow was constrained by placing each crystal in a close-fitting hole in a plate of copper or iron of equal thickness and rolling the plate and crystal together. About one-third of the crystals were rolled in a "sandwich" pack by adding top and bottom cover plates. The two-high mill used had 8-in. diameter rolls and was operated at 15 r.p.m. The initial diameter of the crystals was between 1/4 and 1/2 in., while the starting thickness varied from 0.031 to 0.376 in. With a single exception, which was rolled 63 per cent, the crystals were rolled to a final reduction in thickness of 82 to 97 per cent in 20 to 40 passes, alternately changing the sense of the rolling direction. The initial orientations of the crystals were determined either by X-ray back reflection12 or by optical reflectionl3 from etch pits; the mean final orientations were determined by X-ray Laue photograms using molybdenum, silver, or tungsten radiations, by optical reflection, and in many cases by both methods. Results Twenty-six crystals were studied. It was found that there were three typical be-

Jan 1, 1941

By B. McFadzean, P. E. Ngoepe, P. P. Mkhonto, J. Taguta

The adsorption of heterocyclic collectors such 2-mercaptobenzothiazole (MBT), 2-mercaptobenzoxazole (MBO), 2-mercaptobenzimidazole (MBI) and their derivatives on pyrite form a basis in understanding the flotation reactivity that may be applicable in a wide range of sulphide minerals. This study uses a computational and experimental approach to determine the heat of adsorption of MBT, MBO, MBI and modified MBT collectors onto pyrite surfaces. Computational calculations found that the adsorption energies were in the order: MBO > MBI > MBT. The heterocyclic collectors were adsorbed in their thiolate form on the surface. In the case of the pyrite (100) surface, the MBT adsorbed through the exocyclic sulphur atom, while MBO and MBI adsorbed through the exocyclic sulphur and N atoms onto the 5-coordinated Fe atom. The (111) surface was found to be more reactive and different adsorption mechanisms were predicted, where the MBT exocyclic sulphur atom bridged on the 5- coordinated Fe and surface 2-coordinated sulphur atoms, while the N atom adsorbed on the 5-coordinated Fe atom. In the case of MBO and MBI, dissociation of the exocyclic sulphur atom from the collector occurred with subsequent interaction with the surface 5-cordinated Fe and 2-coordinated S atoms. This resulted in the collector carbon atom adsorbing on the surface 2-coordinated S atom, while the N atom adsorbed on the 5-coordinated Fe atom. The adsorption of the modified MBT was found to be more exothermic than the MBT, which showed that introduction of a –CS2 group on the exocyclic sulphur atom improved the affinity of MBT on the surface, and was thus a better flotation collector. The computational results were supported by experimental enthalpy of adsorption measurements and microflotation tests. The chemistry of the heterocyclic thioamides is complicated by the fact that they can exist in a number of tautomeric and ionic forms at different pH’s. This is discussed in relation to the flotation and calorimetric data.

Jan 1, 2018

By R. P. Carreker, J. C. Fisher

Cheep tests are normally constant load tests. Such tests approximate some types of service conditions and therefore are justified from the engineering point of view. Coupled with this consideration is the advantage of simplicity inherent in constant load tests, as contrasted with the comparatively complex requirements of a constant stress test. It is not surprising that the vast majority of creep tests reported are of the constant load type. Despite the enormous amount of accumulated creep test data, plastic flow is by no means completely understood. The widespread use of constant load tests is at least partly responsible for this lack of understanding. Any attempt to analyze deformation must involve the more fundamental quantity stress, rather than load. It is possible to predict constant load behavior from known constant stress data, but the reverse is much more difficult. When a metal specimen elongates, as in a creep test, the cross section decreases, maintaining constant volume. Thus For a constant stress test the force on the specimen must be decreased as the cross section decreases, that is, this force must be inversely proportional to the elongation of the specimen. An-drade has described three methods of obtaining the constant stress condition,l-3 each of which is relatively complex. The most recent proposal,³ suggests a major simplification which maintains the simplicity of the constant load test while approximating quite closely the desirable condition of constant stress. Andrade's device is admittedly more accurate but the method described below has definite advantages Consider a specimen in the form of a "V" supported at its ends. If a weight be applied at the vertex of the angle, the stress in each leg of the "V" If this stress causes an elongation ?1 in each leg of the "V," the angle decreases from a. to a smaller angle a1. The quantity sec — thus decreases with specimen elongation while the quantity 1/A increases. By selecting proper initial conditions it should be possible to hold S/So very nearly constant at unity. The proper initial conditions are realized when a0 is made equal to approximately 90°. Fig 1 compares the ratios of S/S0 for a0 = 85, 90, 95, 100°, with a0 = 0, that is, a straight speci- men, for true strains up to e = 0.10. It may prove convenient to measure X, the movement of the vertex, rather than the true elongation 1. Contour lines of X/lo are also plotted in Fig 1. The method for obtaining constant stress described above is especially suited to the testing of small wires, but may easily be extended to rods of any diameter through the use of a suitable grip which serves as the vertex joining two identical rods forming the legs of the "V." References 1. E. N. da C. Andrade: On the Viscous Flow in Metals, and Allied Phenomena. Proc. Roy. Soc., A, 84, 1, (1910-11). 2. E. N. da C. Andrade and B. Chalmers: The Resistivity of Polycrystalline Wires in Relation to Plastic Deformation, and the Mechanism of Plastic Flow. Proc. Roy. Soc., A, 138, 348, (1932). 3. E. N. da C. Andrade: A New Device for Maintaining Constant Stress in a Rod Undergoing Plastic Extension. Proc. Phys. Soc., 60, (3). 304, (March, 1948).

Jan 1, 1950

By Rainer Antretter

The city of Garmisch-Partenkirchen in southern Germany is located at a main transit road to Tyrol in Austria and suffers of a very heavy traffic load. Therefore, the Kramertunnel as a by-pass tunnel is built to release/mitigate the traffic through the city centre. The 3,600 m long single tube road tunnel is designed with a parallel but smaller emergency tunnel and with cross passages, fitted with single- and doublesided emergency bays, a vent shaft, and an intermediate ceiling to separate fresh air supply from the road traffic. The tunnel, concrete lined along its entire length provided the challenge to find smart formwork solutions for quick set-up, repositioning, setup and pouring. Three particularly specific sections are discussed in this paper.

Jun 13, 2023

By John Snowberger III, J. Brent Hiskey

The electrochemical dissolution of super alloys containing different amounts of rhenium was investigated. The initial part of the investigation focused on the anodic dissolution of rhenium from second-generation (3% Re) and third-generation (6% Re) nickel based alloys. Exploratory electrochemical tests were conducted to evaluate solution chemistries and to establish fundamental dissolution behavior of the alloys. These included rotating disc electrode (RDE) cyclic voltammetry, linear sweep voltammetry, and chronoamperometry tests. Electrolytes comprising sulfuric acid, hydrochloric acid, and ammonium sulfate were examined. Of these, a 0.1 M HCl solution proved to be extremely effective for electrochemical dissolution of samples of CMSX-4, CMSX-10, and SC-180 alloys. This paper discusses in detail the electrochemical behavior of these alloys.

Jan 1, 2014

By Edwin T. Myskowski, Alfred H. Hesse

THE development by the U. S. Bureau of Mines of a process for purifying manganese by electrolysis has stimulated interest in manganese alloys. While recent publications have shown some alloys of manganese and copper to possess rather unusual properties, none have included information on tensile properties, which have an important bearing on the usefulness of the alloys. Manganese-copper alloys can be heat-treated, since the single phases that exist at high temperatures may be retained by quenching. According to Persson,1 when quenched alloys containing from about 30 to nearly i00 per cent manganese are reheated, alpha manganese is precipitated (Fig. I). Calculations based on Persson's X-ray data indicate that this decomposi¬tion is accompanied by a change in volume of as much as S per cent. The reason that this large volume change has not been noted probably is the slow rate at which equilibrium is reached by these alloys. In an investigation on hardening by cold-work and heat-treatment, Dean and Anderson3 found that quenched alloys increase in hardness with manganese content and that high-manganese alloys harden very slowly with cold-work, while high-copper alloys harden much more rapidly. Heat-treatment has little effect on manganese-copper alloys containing less than 40 per cent Mn, and affects those alloys containing more than 40 per cent in accordance with their manganese content and heat-treating temperature. Dean and Anderson4 also found that cold-work increased electrical resistance of alloys containing from 50 to 80 per cent Mn, and that heat-treatment of alloys containing from 40 to 96 per cent Mn altered the electrical resistance considerably. Dean, Anderson and Potters have shown that the high vibration damping capacity that characterizes manganese-copper alloys containing 40 to g0 per cent Mn. is affected by cold-work and heat-treatments. Highest vibration damping capacity at low stresses was obtained by heating for 2 hr. at 450°C. (842°F.) after quenching from solution temperatures. Preparation of Alloys.-The alloys for these tests were melted in a 17-lb. basic-lined high-frequency induction furnace using electrolytic manganese, grade A ingot copper and a 70-30 Cu-Mn master alloy (69.80 per cent Cu, 0.12 Fe, 0.04 Si, 0.006 S, 0.07 C, balance Mn). The manganese was heated slowly to expel excess dissolved gases and melted before the addition of copper. No fluxes or covers were used. The melts were cast in tapered iron molds and the ingots were reduced go per cent when forged to ½ in. rounds. These rods were given 2-hr. solution treatments at temperatures that depended upon the composition (Table I). Tensile Tests.-The tensile specimens, 0.313-in. diameter (1.25-in. gauge length), which were enclosed in evacuated Pyrex

Jan 1, 1942

By N. I. Tyushkova

This is a brief survey of the technological solutions for deep cleaning of baddeleyite?s concen-trate. Baddeleyite is part of kamaphorite of composite apatite-magnetite ore in alkaline-ultrabasic mountain range of Kola Peninsula. Baddeleyite?s concentrate, which is being produced by Kovdorsky GOK (ore mining and processing enterprise) contains 97.5%~98.5% (Zr?2 + ?f?2) and also scandium oxide (0.05%). It is usually used without any chemical processing. World demand for zirconium oxide is constantly on the rise. Its consumption grows in ceramic industry and in high-tech spheres. That?s why the demand for its purity is very important nowadays (additional cleaning from phosphorus, silicon, iron, aluminium). The mechanism and kinetics of interaction of activated bad-deleyite with sulphuric acid has been studied as well. While applying method of mathematical mod-eling it was confirmed that the mechanical activation is effective for the intensification of sulphation process of baddeleyite?s concentrate with the aim of purifying it from dirt. The use of the calculated optimal regimes allows to reduce such technological operation factors as: temperature, the du-ration of process, the sulphuric acid consumption. It also allows to determine the conditions of anticipatory abstraction of scandium and main dirt in solution in comparison with zirconium oxide.

Jan 1, 2014

By Rak-lun Choi

Plasma-induced damage of InGaN/GaN multiple quantum well (MQW) light-emitting diodes (LEDs) has been studied in terms of forward turn-on and reverse breakdown voltages, together with etch rate and surface morphology. The physical degradation of sidewall along with rough surface morphology of n-GaN caused by increased ion scattering induced the deterioration of the forward and reverse voltages. It was found that the turn-on voltage is sensitive to the surface roughness of the etched n-GaN and the breakdown voltage is strongly affected by the sidewall contamination. Annealing under nitrogen after the mesa etching improved the electrical properties of the InGaN/GaN MQW LEDs. Efficient blue light-emitting diodes (LEDs) were fabricated using InGaN/GaN triangular MQWs. The LEDs with triangular QWs showed a lower operation voltage and 2.4 times higher light output power than those with the rectangular MQW LEDs at 20 mA and 20 °C. The intensity of electroluminescence (EL) at 20 mA was almost independent of ambient temperature in the triangular QW LED, but decreased substantially in the rectangular one.

Jan 1, 2003

By S. Vimalnath

The bioremediation capability of Pseudomonas aeruginosa cells was investigated for the biosorption of lead ions from aqueous solution. The various parameters such as pH, kinetics, biomass loading and concentration of lead affecting the biosorption process were studied. Complete bio removal of lead could be achieved for an initial concentration of 12.4 mg/L at pH 6.2, corresponding to typical industrial effluents. The biosorption isotherm followed Langmuirian behavior and the Gibbs free energy (?G) was determined to be-30.8 kJ/mole, indicative of chemisorption between the functional groups of the bacterial surface and lead. The biosorption kinetics adhered to a pseudo-second order model. The possible mechanisms of interaction of lead with the bacterial cells are discussed. A carbon paste electrode with a coating of biomass was developed for lead ion detection in aqueous solution using cyclic voltammetric technique. Concentrations of lead up to 5x10-5 M could be successfully detected using cyclic voltammetry, which could be improved to a detection limit of 1x10-8 M adopting differential pulse anodic stripping voltammetry (DPASV). Keywords: Pseudomonas aeruginosa, bioremediation, lead, voltammetry

Sep 1, 2012

By Robert Kimutis, Ke Yang, Yi Luo, Jianwei Cheng

"Surface subsidence processes, especially those associated with a longwall mining operations, could cause operational and/or safety problems to railroads. For railroads with normal amounts of traffic, both the limited time window between traffic and the limited space available make the efforts to return the railroad back to its original state nearly impossible. In order to ensure the safe operation of a subsiding railway, the partial lifting method has been developed and applied. This paper describes the principle and application of the method. A case of applying this method to mitigate subsidence effects on a long section of railway has been demonstrated.INTRODUCTIONMaintaining an operational railway as it is experiencing a longwall subsidence process is not an easy task. The subsidence process may induce sufficient strain and curvature to cause problems to the railroad structures. Localized subsidence-induced slope often is significantly larger than the permissible ruling gradient of 0.7% for a locomotive to haul a loaded train reliably. In order to ensure safe operation, it would be ideal to instantly lift the railroad track back to its original level as it is subsiding. However, it is often impractical to do so due to the limited time windows available between railway traffic and the available space on the railroad base.A partial lifting method has been developed to keep the railroad operational under such limitations. The subsiding railroad track is raised by only a determined, partial amount of the occurred subsidence at a given time. By making such a determined adjustment, the railroad track can be maintained on a smooth and operational profile, and the high strain and curvature on the railroad structures can be reduced as well. To define a smooth railroad track profile in a subsided section the following two conditions should be met: (1) the maximum railroad gradient should be less than the permissible ruling gradient, and (2) the recommended amount of adjustment should be able to be made by the repair crew within the available time windows between scheduled railway traffic.The subsidence effects on a long section of railroad over two longwall panels have been successfully mitigated using the partial lifting method. The railroad experienced a maximum subsidence 89 of about 5 .0 ft (1.5 m) with the average subsidence along the entire length being about 3.45 ft (1.05 m). However, the average adjustment due to lifting that was made along the entire length of the subsidence-influenced railway was only 0.5 ft (152 mm)."

Jan 1, 2010