Search Documents

By A. Yoshikawa, T. Sugeno

To detenmine the origin of the sharp fatigue limit in many ferrous metals, S-N curvces were determined in push-pull fatigue at 18.6 kc per sec at room temperature and - 67°C for various kinds of iron. These differed in carbon and nitrogen content and grain size (25 and 2500 grains per sq mm). Sharp knees appeared in the S-N curves of fine-grained specimens with high interstitial content at both temperatures. In coarse-gruined specimens, knees were not sharp .regardless of the interstitial content and the testing temperature. It is concluded from these results that the controlling factov for the appeavance of the sharp fatigue limit is not strain aging but grain size. It has already been mentioned that iron and some iron alloys show fatigue curves characterized by a more or less sharp knee and a fatigue limit.' Explanations of the origin of this characteristic behavior of fatigue in iron appear to fall into two broad classes. One is concerned with interstitial impurities through the aging or locking effect and the other is based on intrinsic plastic properties of iron. Levy and sinclair2 and Lipsit and Horne3 have suggested that the fatigue limit observed generally in iron and steel is due to interstitial solute aging during the course of fatigue. On the other hand, Thompson and wadsworthl have suggested that the fatigue limit may be analogous to the sharp yield point, in the sense that alternating stresses above the fatigue limit are necessary to break down the dislocation locking. However, there are some experimental results which cast doubt on the general validity of these suppositions.4-8 Ferro and Montalenti' have recently suggested that the typical form of the fatigue curve of iron seems to come from an intrinsic plastic characteristic of the iron structure. This suggestion is based on the experimental result that pure iron containing an insufficient amount of interstitial solute to alldw appreciable strain-aging effects still showed a fatigue limit at room temperature. Although systematic investigations on the effect of grain size are scarce, it is thought that this effect is important in relation to the sharp fatigue limit. In fact, sensible differences were observed by Oates and Wilson4 in fatigue behaviors of a low-carbon steel depending on grain size. Ideally, the fatigue limit will be defined as the upper limit of stress amplitudes at which the life is infinite. This ideal fatigue limit can never be determined because of the limited time available for experiments, and moreover scattered data points often leave the construction of S-N curves somewhat arbitrary. And, it is usually stated that a material has a fatigue limit when its statistical S-N curve becomes apparently parallel to the N axis with a more or less sharp knee. The meaning of the fatigue limit and the sharp knee will be discussed in detail in relation to the construction of S-N curves. The origin of this sharp knee was investigated by determining S-N curves of iron for various interstitial contents, testing temperatures, and grain sizes. EXPERTMENTAL PROCEDURE The material as received was a commercial-grade low-carbon steel in the form of 4-mm-diameter rods with the following composition in weight percent: C, 0.09; Si, 0.017; Mn, 0.43; P, 0.006; S, 0.012; Cu, 0.11. Five different groups of specimens were tested. The grain sizes and interstitial contents in each group are given in Table I. The specimens of group C-02 were decarburized by annealing for 100 hr at 700°C, followed by an additional 100 hr at 850°C in wet hydrogen. Specimens of groups N-2 and N-9 nitrided in a mixed atmosphere of ammonia and hydrogen after an initial treatment identical to group C-02. The specimens of group C-9 were prepared in a manner similar to those of group C-02, except heat treatment was carried out in a vacuum. After polishing their surface with emery paper, the specimens of all groups were given a final anneal for 30 min at 930°C and air-cooled in an evacuated quartz tube. For group C*-9 this

Jan 1, 1965

By Leandro Scheffer Cipriani

A microestrutura e as propriedades mecânicas de um aço de alta resistência submetido a resfriamento rápido empregando equipamentos (Roller Quench e CLC - Continuous On-Line Control), presentes na linha de laminação a quente da Usina de Ipatinga – Usiminas, foram avaliadas nesse estudo. A microestrutura obtida foi composta por bainita e ferrita, com frações desses constituintes variando em função do equipamento utilizado. Devido a essa diferença, os valores de limite de escoamento e de resistência foram maiores no aço submetido a resfriamento via CLC. O resfriamento imposto via Roller Quench propiciou ao aço uma maior tenacidade, medida pela energia absorvida em ensaio de impacto Charpy.

Oct 30, 2017

By Amanda Cristina Medeiros da Silva

Este trabalho tem o propósito de avaliar a temperabilidade de um aço SAE 1040 através da utilização do ensaio Jominy e posteriormente promover tratamentos térmicos, gerando nos corpos de prova condições de arrefecimento diferenciadas para avaliar a influência da severidade de têmpera da salmoura e óleo. A curva de ensaio Jominy gerada apresentou um comportamento coerente para um aço com médio teor carbono. Já os tratamentos térmicos que foram realizados posteriormente revelaram que o meio que gera o maior acréscimo nas propriedades mecânicas é o resfriamento em salmoura, haja vista que os corpos de prova submetidos a este resfriamento apresentaram o maior de dureza.

Aug 16, 2017

By Rafael Eduardo Gomes Ribeiro

O fenômeno de degradação granulométrica de minérios devido à crepitação se apresenta como uma fonte geradora de finos que em excesso prejudica a permeabilidade da carga e diminui o rendimento da produção. Neste trabalho, realizou-se um estudo da crepitação de minérios de ferro da Sidermin (Siderúrgica Mineira) para dois períodos diferentes de 8 dias cada, num primeiro período o mecanismo de secagem do minério estava ativo e no outro seguinte não estava. Os resultados para crepitação foram satisfatórios pelo processo de pré-secagem do minério de ferro com gás de topo, pois resultou num aumento de produção por amenizar o fenômeno de crepitação.

Aug 7, 2018

By Matheus Sexto Alexandre Pereira

Controle e centralização de informações referentes ao processo industrial são imprescindíveis e considerando-se que na cadeia de suprimento o maior valor agregado costuma estar na produção, faz todo sentido investir em sistemas que possibilitem a otimização do fluxo, controle e qualidade do processo. O novo Sistema de Controle de Panelas (SIPAN) implantado na CSN permitiu monitorar em tempo real todo o ciclo operacional utilizando novas tecnologias de desenvolvimento de software web, além de melhorar o gerenciamento, comunicação com outros sistemas e rastreabilidade de todo o processo. O sistema implementado conseguiu melhorar a qualidade de informação para a equipe tornando mais rápida e assertiva a tomada de decisão.

Jul 30, 2018

By A. H. Bromly

The small agricultural village of Santa Barbara, in the State of Guanajuato, has been the center of spasmodic tin-mining operations during recent years. The deposits, so far as I know, are unique, and a few brief notes may be of interest. Santa Barbara, about 12 miles west of San Felipe station on the Mexican National Railway, and at an elevation of 2,400 m. above sea-level, is situated in a flat valley extending east and west, and bounded north and south by broken rugged hills rising about 330 m. above the general level of the valley. Tin-mining operations have been conducted at the Queensland mine, near this village. A small concentrating-mill was erected and attempts were made to smelt the ore in reverbera-tory furnaces. The country-rock of the district for many miles is rhyolite of great thickness. There are some local variations due to differences in cooling, or subsequent alteration or impregnation; but throughout the whole district the principal constituents of the rocks remain the same, viz., free silica, orthoclase-feldspar and sanidine. The latter is especially marked. The crevices and joints of the rock are frequently filled with calcedonic and opalescent quartz. The ore-formation at the Queensland mine is of an unusual nature, consisting of cracks in the rhyolite which have been filled with clay. This phenomenon is largely developed over a width of from 80 to 100 m., in which the principal fissuring follows an approximate direction of north and south. The average dip ranges between 70 and 80 degrees. Some of the fissures hold sufficiently true for a time to afford the impression that they are due to dynamic causes, or earth-movement. This may be true of some of the north by south fissures; but considering

Jan 1, 1906

By Steven Derycke, Stephen C. Tadolini, Anand Bhagwat

"The tensile and shear strength of intrinsic bolting support systems has always been a major concern of designers. A comprehensive laboratory testing program was designed to evaluate the tensile and shear strength of individual wires and completely wound PC-strand cables. PC-strand cables with smooth wires and the recent anchorage enhancement innovation of indentation were evaluated and compared. The testing protocol detailed in ISO Standard 15630 utilizes a mandrel system that was investigated at 3 different diameters which alters the wire to mandrel ratio from 2:1 to 9:1. The results demonstrate that the difference between smooth and indented wires is statistically insignificant when larger diameter mandrels are used, and that indentation does not adversely affect strand properties and performance. Insight into the shearing mechanism and evaluation techniques are discussed with the introduction of triaxial loading to describe the PC-strand tensile and shearing mechanisms. Another important result indicates that the shear strength of PCstrand cable bolting systems has a greater shear strength value than traditional steel bar bolting systems.INTRODUCTIONPC-strand cable bolts have proven to be a global cost effective ground control solution in metal/non-metal and coal mines. The inherent strength to weight ratio of cable supports, combined with flexibility has been used in underground entries that range from 20 to less than 1.2 m in height (65 to 4 ft). In coal mining, the systems are used as primary and secondary support installed both passively or actively with installation tensions that range from 38 to over 178 kN (8,500 to 40,000 lbs) . While cable can be specified in several diameters, the most predominant sizes in the US remain 15.2mm (0.6 in) and 18mm (0.7 in). The capacity of the systems defined in the ASTM 432-13 is 90% of the minimum strand strengths of 260 kN (58,600 lbs) and 320 kN (72,000 lbs), respectively.Cables are not only suitable to support vertical loads, but are also often used to effectively support fractured and jointed materials and can be exposed to shear forces across the wound PC-strand structure. In fact, Goris et al. reported that cable bolts placed across jointed surfaces could more than double the shear resistance. These results were duplicated for both smooth and rough jointed surfaces (Goris et al., 1996). An example of tensioned cable bolts used to support a fractured and sliding roof in a longwall tailgate entry is shown in Figure 1."

Jan 1, 2015

By Edward Estabrook

THIS paper gives a brief account of the geologic and production problems encountered in the Grass Creek oil field, the methods used in their solution, and the beneficial results obtained from the work. The author wishes to acknowledge the assistance received from J. H. Pearson and Miss Ninettta A. Davis in the collection of the data and the preparation of the cross-sections. Permission for its publication was given by the officials of the Midwest Refining Co. and the Ohio Oil Co. The Grass Creek oil field is located in Ts. 98-99 W., R. 46 N., Hot Springs County, Wyo. The productive area includes about 2 1/2 mi. (4 km.) on the apex of a great anticlinal fold occupying more than 150 sq. mi. Fig. 1 shows the structural contours of the field. Oil was dicovered in the field in June, 1914; development proceeded rapidly and production rose to a maximum in 1918. The marketed production has been approximately as follows: BARRELS BARRELS 1915 94,073.5 1918 2,946,774.27 1916 1,404,183.97 1919 2,000,584.84 1917 2,780,697.51 1920 1,485,080.94 About 350 wells, 800 to 1500 ft. (243 to 457 m.) deep have been drilled to reach the upper oil sands; two companies, the Ohio Oil Co. and the Midwest Refining Co., operate the entire field.

Jan 2, 1922

By Bastiawarman Rifki, Nugraha Nico, Priatna Anton

The Deep Mill Level Zone (DMLZ) is one of the underground mines operated by PT Freeport Indonesia (PTFI). DMLZ is located approximately 1,500 m below ground level, where dominant rock types are skarn and diorite. The DMLZ mine and layout was designed based on the previous mine located above ground, the Deep Ore Zone (DOZ). The DOZ mine, located approximately 1,000 m below ground level, was a proven success, with a maximum capacity of 80K tonnes per day. During the production ramp up, which started in 2015, the DMLZ experienced several seismic events. The most significant event occurred in January 2018 with a recorded magnitude of more than 2.0 Mw, which resulted in a 14-month delay of the undercutting until March 2019. The significant event in January 2018 required the DMLZ to apply several adjustments related to the mining plan to help ensure it could continue development and achieve production target safely. This paper will describe the changes in the DMLZ mine plan as a response to the seismic activity at the mine, the reason behind the decisions being made to change the mine plan and strategy, as well as strengths and weaknesses between the previous plan compared with the new plan.

Apr 26, 2022

By Akira Usui

Occurrence of hydrogenetic ferromanganese crusts has been well documented over inactive seamounts in the central and southern Pacific Ocean. It has been thus believed that the hydrogenetic crusts develop preferentially at water depths between about 800 to 2500 meters. In fact, according to the Manganese Crust Database (F. Manheim, 1988), only two occurrences are known at water depths below 5000 m out of 819 occurrences cited in the database. Unexpectedly, we found typical hydrogenetic ferromanganese crusts from deep-sea floors; 1) outcropping old volcanic basement over the Philippine Sea Plate (abandoned spreading centers and subducting old oceanic crusts) and 2) one from the slope of an abyssal hill in the Central Pacific Basin (Cretaceous deep-sea basin) at water depths ranging between 5200 to 6100 meters. We report their occurrences with submersible observations from Shinkai 6K, physical parameters (such as thickness of crusts about 2-4 cm in maximum), chemical composition, petrology of substrate, and results of Be-10 dating for some samples in comparison with typical Co-rich manganese crusts from the Central Pacific seamounts. The preliminary chemical and mineralogical analyses reveal that they are of typical hydrogenetic origin, and typical of iron-manganese oxide mineral, vernadite, slow and probably continuous growth, and lower content of Co than the Central Pacific seamount crusts. The occurrences and nature of the crusts indicate that deep-sea floors are also optimal for the growth of hydrogenetic crust even at 5000 m water depth or deeper, only if oxygenated deep waters are supplied and the sea-floor morphology keeps stable enough for significant geological time period. Additional details of chemical analyses will be prepared by November and to be shown in the conference.

Jan 1, 2001

Ancient volcanogenic Cu-Zn-Pb-Ag-Au massive sulfide ores commonly have associated with them along strike and in the immediate hanging wall a distinctive sediment that is thin, usually cherty and metal enriched, and generally referred to as an "exhalite horizon" or "tuffaceous exhalite". Typical examplks include the 13 Ma tetsusekiei of the Kuroko deposits of Japan (Kalogeropoulos and Scott, 1983, Econ. Geol.) and the 2700 Ma contact tuffs of Noranda, Canada (Kalogeropoulos and Scott, 1989, Can. J. Earth Sci.) and Key Tuffite of Mattagami, Canada (Liaghat and McLean, 1992, Explor. Min. Geol.). Attempts to use trace element distributions as lithogeochemical guides to ore have been largely unsuccessful. Exhalites have been considered to be the products of seafloor hydrothermal activity that is peripheral to the main ore-producing vents. However, large actively-forming polyrnetallic sulfide deposits at the Explorer mid-ocean basalt spreading ridge (1 850 m depth) in the NE Pacific and the eastern Manus back-arc dacitic spreading center (1650 m depth) in the western Pacific have demonstrated that the exhalite horizons are more likely produced by fallout of particulates from the main hydrothermal plume. In a typical hydrothermal plume, grains of >27 µm represent up to 97% of the mass (although only 2% of the population) of the particulates and are calculated by Stokes equations to fall from the plume to the seafloor within a few krn of their source. The particles are primarily composed of anhydrite, barite, amorphous silica, iron oxyhydroxides and metal sulfides and oxides. Plumes are subject to bottom currents which push them in preferred directions, just like smoke plumes in the atmosphere are subject to the vagaries of wind direction. Bottom currents in the deep ocean can be 50 m/min or

Jan 1, 1993

By J. Kalliokoski

As part of a funded project we have completed a comparative literature survey of the US regional Proterozoic geology. For our com¬parative study model we used the geological settings of the very large pitchblende deposits in Saskatchewan, Canada and the Northern Terri¬tory of Australia. These occur in a variety of Archean and Lower Proterozoic host rocks, at and below a regional unconformity that is capped by subhorizontal Middle to Upper Proterozoic conti¬nental sedimentary rocks. We find that there have been recorded in some parts of the US similar unconformable sequences of Middle to Upper Proterozoic continental sedimentary rocks that overlie older basement rocks.

Jan 1, 1979

Flat jack stress determinations in selected colliery roadways have revealed a range of measured stress from 330-p.s.i. tension to 3,750 p.s.i. compression. Photoelastic examination of loaded plastic and actual rock mo.odel mine openings has shown that the primary horizontal stress required to attain these measured stresses would be from one to three times the superincumbent vertical load.Examination of roof movement with a. borehole oxtensumeter and a series of anchors at various horizons to 30 feet in a. vertical roof borehole showed that when a standing face waa.s advanced the roofmovement was practically confined to the lower two feet. The ma.j ority of this movement occurred during the 36 hours after mining at this face commenced.The use of a. radioactive isotope and a. scintillation counter in a. pair of parallel bcreholes promises to be sensitive and accurate method of roof bedding plane crack detection.

Jan 1, 1963

By Robinson T

The paper describes a spreadsheet system that enables selection of projects and companies that meet the user's corporate exploration and/or acquisition philosophy. A regularly maintained commercially available database has been used as the basis for this system. It provides an easily accessible efficient com- prehensive search method. The technique enables ranking by various criteria, both technical and financial, to provide groups of projects/companies that are of interest. Initially, target size parameters such as reserves, production and mine life are applied together with geological criteria such as age and deposit type; the significance of the targets in the context of the Australian gold industry is addressed.

Jan 1, 1988

By D. Papazoglou

This work was undertaken to investigate the thermodynamic and kinetic feasibility of using hot sulfur dioxide bearing gases from smelting processes to selectively sulfate the nickel in nickel laterite ores for subsequent extraction in water. The environmental benefits of this approach, as opposed to releasing the gas to the atmosphere, and the economic benefit of directly utilizing the SO2 rather than converting it to sulfuric acid are strong drivers for such a process. A thermodynamic analysis indicated that selective sulfation of the nickel could be feasible under appropriate conditions and these were explored through a series of laboratory scale experiments. Laterite samples were reacted at temperatures between 500 and 800°C with an equilibrated mixture of sulfur dioxide, oxygen and nitrogen in a fixed bed reactor. Tests were conducted on saprolitic ore from Bulong, Western Australia:, limonitic ore from New Caledonia and gamieritic ore from Indonesia. Nickel extractions were highest from the limonite and relatively low from the other ores. The maximum selective extraction of nickel from the limonite in a single stage sulfation was 73%. Sulfation of other elements present in the laterites was also examined. A two-stage process was also identified which involved sulfation using a strong sulfation potenrial followed by weaker sulfation potential to attempt to convert ferric sulfate formed in the first stage to ferric oxide. This increased the extraction for the limonite ore to around 84% Ni, 95% Co and 2% Fe. Direct sulfation of laterite could be feasible in locations where sulfide smelting or roasting operations are relatively close to laterite deposits.

Jan 1, 2003

By Y. C. Liu, R. H. Richman

The effects of gel,manium and tin on the deformation and 9-e-crystallization textures of copper have been explored in detail with in the copper-rich terminal solid solutions. Addition of solute to copper produces a change in deformation texture from the copper type to the 70 :30 brass type. This transition has been measured quantitatively The types mid proportions of recrystal-lization components have been determined as a function of com-position, and correlation of recrystallization components with specific deformation components is discussed. On the basis of information available in the literature, it has been suggested that the effect of solute elements on the recrystallization texture of copper

Jan 1, 1961

By Moxon N. T

The detonation pressure of ANFO can be significantly reduced by the addition of low density materials such as polystyrene, bagasse, swadust or perlite. Laboratory and field test results have shown that homogene- ous mixtures of these low density explosives can be produced in a bowl truck and loaded into a blasthole without segregation. The detonation pressure of the mixture can be altered to be more compatible with the material in which it is being used by varying the quantity of low density additive incorporated into the mixture. Field results have shown that these low density explosives can lead to significant cost savings without com- promising fragmentation or production.

Jan 1, 1989

By B. M. Thethwayo

Graphite blocks are currently used in the concentrate - slag zone in primary PGM smelters, and can possibly be extended to the matte zone. This project evaluates the interaction between synthetic matte and graphite blocks on a laboratory scale. Static crucible tests were performed where graphite crucibles (prepared from standard and high-grade graphite) were filled with synthetic matte (27.7 per cent S ? 46.1 per cent Fe ? 17.0 per cent Ni ? 9.2 per cent Cu) and heated to 1550°C for different time periods (1?5 days). Matte penetration was evaluated using a SEM, while graphite dissolution was evaluated by measuring the carbon content of the matte with a LECO carbon analyser. Matte penetrated into standard grade graphite up to approximately 2 mm, while matte infiltration into the high grade graphite was limited to the immediate hot face. The saturation solubility of graphite in the synthetic matte at 1550°C was 0.43 per cent. Copper, iron, nickel, and sulphur were detected in an accretion that formed in the water-cooled part of the furnace. This accretion consists of mainly Cu-S and Cu-Fe-S based phases.

Jan 1, 2012

By Tamilis Rodrigues Braga

Embora a indústria de fundição recicle toda espécie de sucata metálica, usada como matéria-prima no processo, é uma grande geradora de resíduos sólidos, devido, principalmente, à elevada quantidade de areia empregada no processo. As fundições precisam adotar alternativas que minimizem o descarte das areias. A reciclagem interna, por meio da recuperação mecânica, se estabelece como uma opção com benefícios econômicos e ambientais. Neste trabalho foi avaliada a influência da utilização da areia de cura a frio recuperada nas propriedades mecânicas do molde e no acabamento do fundido. Verificou-se que é possível a utilização de até 50% de areia recuperada no processo de moldagem, mantendo propriedades adequadas de desempenho.

Oct 30, 2017

Cyanidation tests by bottle agitation were conducted on an oxidized lead-silver ore containing approximately 12% Pb and 500 g/t Ag. Over 60% of the silver was leached when the ore was ground to 100% passing 0.15mm, whereas 50-60% of the silver was leached when the ore was only ground to 100% passing 0.5mm. Slurry handling and dewatering at the fine grind size were very difficult due to the high clay content of the ore, however this problem was greatly reduced at the coar- ser grind size. The silver recovery at the fine grind size was very dependent on cyanide solution strength with stronger cyanide sol- utions (containing more than 0.1% NaCN) re- sulting in lower solution silver contents. This was thought to be due to the precipi- tation of leached silver by zinc, which was also leached from the ore by the higher cyanide levels. There was a critical zinc level in solution of approximately 1000ppm, above which the silver recovery fell markedly. Cyanide and lime consumptions for this ore were high (typically 5 kg/t and 40 kg/t respectively), hence the processing of this particular ore by cyanide leaching is un- economic at current silver prices.

Jan 1, 1987