Search Documents

By James F. Reynolds

Introduction There are 1.4 Gt (1.5 billion st) of recoverable coal under less than 914 m (3,000 ft) of cover in Colorado in pitching seams. Snowmass Coal Co., in cooperation with the US Department of Energy, introduced the longwall mining method in pitching seams to North America. This venture is a coal mining research program directed toward the profitable production of coal under difficult mining conditions as found in pitching seams of the western US. Snowmass Coal classifies pitching seams into the following categories for longwall on the strike in seams 3 m (10 ft) or less thick: • Flat = 0 to 10°: Normal continuous mines and shuttle cars work efficiently. • Slight = 10° to 22°: The maximum pitch that rubber tired equipment will function. • Moderate = 22° to 40°: The angle of repose of mined coal. • Steep = 40° to 60°: The limit of safe use of this roof support. • Vertical = over 60°. The longwall roof support covered here will work in all pitches except vertical. The shearer and conveyor will work in flat through moderate conditions. Longwalling across strike with this equipment in seam pitch over 60° could be accomplished with an inclined face. Development of the first longwall panel began in 1979 and was completed in 1981. The longwall equipment was installed and mining began on Aug. 11, 1981. Mine Planning and Development The original mine plan took advantage of old works abandoned in the 1960s. The gates were developed on a two-entry system with the entries rising 2° to the strike, allowing water to drain from the face. The mining method was by Alpine F6A road header continuous miners with bridge conveyor type coal transport into 5.4-t (6-st) bottom dump coal cars hauled on 1.1-m (42-in.) gauge track by 7.2-t (8-st) battery locomotives. The initial concept was to haul coal from the longwall by battery locomotive. Lack of discipline, however, was shown in the irregular direction of the gate entries, and local rolls in the coal seams severely limited the capacity of battery locomotives. Current mining law prohibits using an intake escapeway for belts or trolley locomotives. A two-entry system is the simplest method of panel development in a pitching seam. A continuous miner cannot be trammed from one entry to another because of steep "X" cuts. Thus, the development requires a continuous miner in each entry. The configuration of the old mine works resulted in a first panel longwall block of three 108 m x 1.6 km (355 ft x 5,400 ft). In panel development, the use of battery locomotives for coal hauling became evermore costly. When the panels were completed and the setup room finished, the lower gate entry was changed to a belt entry and battery locomotives were abandoned. A new slope was driven and the mine supply system was converted to rubber tire diesel supply. The latest generation of roadheader and standard high powered shuttle car-to-belt system is now used for development. Selection of Longwall Equipment Longwall mining across the strike on pitching seams is currently practiced in many nations. Equipment similar to that used by flat seam longwalls is available for pitching seam use in Great Britian and Germany. Face equipment includes a twin outboard armored face conveyor. It was selected to give maximum retention of coal on the conveyor due to flight rigidity and to prevent coal from sliding down the face and jamming the lower belt gate. Also selected was a 22-mm (0.9-in.) Dowty twin-outboard face conveyor for a 106-m (350-ft) face with a single 112-kw (150-hp) drive

Jan 12, 1983

By R. H. Watson

A paper read by J. A. H. Church before the Northern Alberta Branch last February described a method of working thick inclined coal-seams from the dip upwards, with the view to preventing fire risk by using water for the stowage of waste workings, and extinguishing a conflagration should such break out, was favorably received; but there was some doubt as to the cost of such a method, as it involves a retreating system, which might prove too expensive for practical adoption. Let us consider a typical leasehold such as we are familiar with in the Rocky Mountains. The leasehold is crossed at one end by a mountain river, which is cut by the outcrop of a seam of coal, 30 feet in thickness, pitching as shown on the drawing herewith, which also shows the general line of the outcrop in elevation through the leasehold, which is two and a half miles long and contains 1,500 acres. The average lift is about 600 feet above river level and drilling has proved that the coalseam can be tapped at a depth of 1,500 feet, 2,000 feet down the pitch from the outcrop in the river, all as shown in the illustration, which is typical enough of our mountain conditions to serve the purposes of comparison of methods. We take up the leasehold and invest $30,000 to pay for drilling and prospecting; $30,000 more for the price of the lease to locator or holder, and say $100,000 to pay for a railway spur (it might cost twice this sum, but we are only comparing two methods in the same location) and "now we are ready to consider equipment and the cost of development.

Jan 1, 1924

By Sidney A. Swensrud

Much has been said and written about uneconomic and evil marketing practices in the oil industry, including such factors as loaning of equipment, price cutting and secret prices, commercial discounts, abuses of credit cards and coupon books, and so forth. It is not my purpose here to add to the discussion of those problems, but rather to attempt a discussion of some of the more basic factors in the general distribution economies of the industry. The economics of distribution in the oil industry cannot be regarded apart from the general economics of the industry as a whole. The attempt to regard them as separate has led many people into the fallacy of believing that the responsibility for the apparent evils in the marketing end of the business lay entirely at the door of the marketing end. Such a view fails to take cognizance of many underlying factors; we can only expect to understand the distribution economics of the industry if we understand its general economics. We must realize also that the oil industry today is essentially the gasoline industry. The oil industry may be said to have begun about 60 years ago. At the outset it was concerned chiefly with the manufacture and sale of kerosene, lubricating oils and greases. Gasoline was then a most obnoxious by-product. The early oil-marketing company was engaged almost exclusively in refining and marketing—it did not concern itself with production but bore the relation to it merely of a purchaser. It may be said that the urge of marketing development in those days, therefore, came from the refining and marketing end of the business. The raw material had not yet begun to exert its enormous pressure, nor had the producer of crude oil acquired a direct interest in the sale of the ultimate finished products. Since then great changes have taken place. With the development of the automobile came a vast new demand for the raw material from which gasoline could be made. No longer could the refining and marketing companies be indifferent to the source of that raw material, particularly in view of the pessimistic outlook then presented as to the probable quantity of oil in existence. And despite the complete overturning of those early estimates, made before the bounty of nature and the skill of

Jan 1, 1931

By N. V. Nayak

Maharashtra State Road Development Corporation Ltd., has initiated a scheme for construction of 55 flyovers in Mumbai in India. To ensure speedier completion of projects several new technologies were adopted to save time without compromising on safety and reliability. Many of the flyovers involved large diameter pile foundations carrying loads ranging from 3500kN to 1375kN. Significant time would have been lost in using conventional load testing procedure to check pile capacity apart from the difficulty in mobilizing the load and the obstruction to site movement and traffic on the adjoining roads. High Strain Dynamic Testing was introduced on the project sites in lieu of static load testing after conducting numerous co-relation studies on various project sites. A total of seven co-relation studies have been conducted till date and based on these data static testing has been replaced by dynamic testing on numerous flyovers. The paper presents the results of such studies. CAPWAP analysis was also conducted on the data to evaluate the percent skin friction and end bearing so as to improve future design parameters.

Jan 1, 2000

By R. D. Parks

DESPITE the handicap of reduced production in many districts, the mining industry in 1938 forged steadily ahead toward solution of its minor technical problems and has of-defected major advances in several fields. In California hydraulic mining for gold, shut down for forty years, will shortly be resumed following revision of restrictive laws. Disposal of hydraulicked ground is to be regulated by settling dams so as not to interfere with agriculture. Gold mining has been aided also by the development of a new high-efficiency dry amalgamator which applies the Ramsay mercury separator to the original de Phily process. Based on the principle that crushed ore will follow a rod into a mercury bath, this simple device is primarily adapted to dry areas and is to be available in small, multiple units suitable

Jan 1, 1939

Societal influences, needs, and uses for recyclable materials are becoming increasingly important business and economic factors in the traditional natural resource companies. Several metals (such as steel, aluminium, zinc, lead and cadmium) are amenable ro recycle which eliminates solid waste generation and decreases the depletion of natural resources. In recent years, the non-ferrous industries have begun to recycle more materials and the next decade will see even larger recycle efforts. In addition to the traditonal recyclable materials, existing metallurgical plants are, or should be, able to handle and recycle materials viewed as 'hazardous'. Unfortunately, some national and regional regulations hinder, and in some cases prevent, the recycling of certain materials. Zinc Corporation of America (ZCA) is currently the largest producer of zinc metal in the USA and one of the world's largest producers of value-added zinc products. Over the last few years, ZCA has become one of the world's largest recyclers of zinc from various diverse materials. ZCA considers these recyclable materials as valuable 'land mines' that provide economic alternatives to the depletion of natural resources while serving society in the minimisation of solid waste disposal. Using the current production facilities of ZCA as a model, this paper overviews the recycling of zinc-bearing materials with special emphasis on: 1. the amenability for recycle within ZCA's pyrometallurgical and hydrometallurgical operations, 2. the quantities and economics of recycle, 3. the problems of recycling hindered by current national and regional regulations, 4. the concepts of total recycle rather than just recovering zinc while generating a modified solid waste, and 5. the motivators for recycling.

Jan 1, 1993

By Najdat I. Aziz

There are different schools of thoughts about the influence of gas pressure on coal strength. Researchers have reached contradictory results with regard to the effect of confining gas pressure on tensile strength of coal. Accordingly, this paper re-examines the influence of gas pressure on the strength of coal. A specially designed precision drill capable of drilling in a pressurised chamber was used to drill coal samples under both atmospheric and increased gas pressure environment. The drill cuttings were examined for particle size distribution using a laser controlled Malvern Mastersizer S particle size analyser. Petrographic analysis of the sample examined the effect of gas pressures on the maceral structure and the composition of coal. The paper demonstrates that there is a definite variation in the range of particle size distribution with particles obtained from drilling coal samples not subjected to gas pressures, in comparison with those obtained from samples drilled under confined gas pressure. Also observed were the changes in the rate of drilling in soft coal obtained from geologically-disturbed zones compared with other coal samples. Some variation on the maceral compostion of coals were also observed in relation to increased gas pressures and gas type.

Jan 1, 1996

By J. C. Haptonstall

The Bismark Mine is located in northern Chihuahua, Mexico, 150 km (95 miles) southwest of Ciudad Juarez (Fig.1). The ore deposit was discovered in 1979 and was placed in production in 1992. The production rate is about 2.4 kt/d (2650 stpd) from an ore reserve of 8.5 Mt (9.3 million st). Grades currently average about 8% zinc, 0.5% lead, 0.2% copper and 50 g/t (1.46 oz/st) silver. Substantial inflows of water into the underground mine complicate the operation. Complex metallurgy poses another challenge for the operators. Bismark is a joint venture with 90% participation by Minas Penoles, SA de CR of Mexico City and 10% participation by Promociones Industriales Banamex, S A de C V (PIB S A) of Mexico City. Anew company, Minera Bismark, SA de CV was formed to operate the property. Cyprus Minerals was a 40% participant in the joint venture but, in early 1993, sold its share to Minas Penoles. The Bismark Mine is one of the largest new underground mining projects built in Mexico during the last 10 years. It is the country's fifth largest underground metal mine and provides about 1 % of the world's zinc supply at about 50 t/a (55,000 stpy). Bismark is a trackless operation with overall productivities of 7.6 t/manshift (8.4 st/manshift). The 2.4-kt/d (2650-stpd) concentrator started up in March 1992.

Jan 1, 1994

By By Staff

"Acid mine drainage can be controlled by water treatment, retardation of the pyrite oxidation reaction system, or enhanced prediction that allows preventive action to be taken. The Bureau of Mines is conducting research in each of these areas; the results of this research are summarized in the eight papers that comprise this volume. Field work to evaluate overburden analysis, alkaline injection, and bactericidal control of acid formation is described, along with two new inexpensive methods to treat acid mine water. These papers were prepared for an acid mine drainage technology transfer meeting held in Pittsburgh, PA, on April 3 and 4, 1985. INTRODUCTIONAcid drainage from coal mines is one of the most persistent industrial pollution problems in the United States. Over 5,000 miles of streams and rivers are adversely affected, primarily by underground mines that have been abandoned for decades. Meanwhile, at active mining operations and at sites where mining occurred after 1977, discharge water must be treated to meet fairly stringent regulatory limits--at a cost to the industry of over $1 million per day.The Bureau of Mines has a special responsibility to facilitate integration of mining and mineral processing with environmental safeguards. This responsibility is twofold: the development of techniques to reduce or eliminate environmental degradation, and the improvement of existing pollution control processes to make them more efficient and more cost effective. Research in acid mine drainage exemplifies the Bureau's concern for these environmental aspects of mining.This collection of papers summarizes much of the Bureau's recent research on acid mine drainage and will give the reader a sense of where the research is headed, in addition to providing details regarding new technology and recently acquired knowledge. The research papers address four basic objectives:"

Jan 1, 1985

By Stephen P. Quin

One of the most prospective undeveloped greenstone belts in Canada, the Hope Bay greenstone belt extends over 80km in a north-south direction and is between 7 and 20km wide. The belt lies on the arctic coast and comprises mafic meta-volcanic and meta-sedimentary rocks that are bounded by Archean granite intrusives and gneisses. The greenstone package has been deformed during multiple events and is transected by major northsouth trending shear zones that appear to exert a significant control on the localization of mineralization. The Hope Bay belt contains a number of significant gold deposits hosted in a typical Archean greenstone belt and which occur in several geologic settings, including shear-hosted, lode-style and breccia-associated. Combined, the deposits host a measured and indicated resource of 1.6 million oz of gold averaging 15.7 g/t plus an inferred resource of 2.7 million oz of gold averaging 12.3 g/t. All deposits remain open to expansion. Exploration in the period 2000-2002 by Miramar includes more than 110,000m of drilling to more fully define the nature of the known deposits, while regional exploration has focused on identifying and evaluating new targets. In carrying out its programs, Miramar uses a number of techniques to improve its chances of exploration success. Activity in 2003 includes 43,000m of drilling focused on expanding resources in the Madrid area, testing the Boston deposit at depth and continuing the hunt for more discoveries. Meanwhile Miramar is advancing one of the deposits towards a production decision, based on a low capital, high return development scenario.

May 1, 2003

By Kissell F. N, Volkwein J. C

The U.S. Department of Interior's Bureau of Mines has the opportunity to visit many U.S. mines, including some that claim 2 to 5 times the national average of 334 raw tonnes/unit shift (tps) from a continuous miner section. In a project to assess the reasons for this high production, the Bureau conducted two studies. The first study focused on the 25 highest producing continuous miner sections. What stood out during the visits-was the quality of the labor-management relations. In each of the mines there was a positive labor/management relationship based on mutual trust and a sense that the employees were the company's most valuable resource. Discussions with labor revealed a universally positive attitude toward the company. Interviews with the mine superintendents invariably ranked the quality and attitude of workers as more important than anything else. Also during the mine visits of the 25- mine study, no engineering factors obviously stood out. Time at the face was greater than average, most were in coal over 1.52 m and the roof was generally good. Also, none of the 25 mines had to contend with high methane levels. Because this study found that a high percentage of mines were in seams less than 1.52 m thick, the second study examined thin seam mines only.

Jan 1, 1988

By V. Budinsky

In recent years the global mining industry has addressed its social and environmental responsibilities and numerous factors have contributed to this. Corporate Social Responsibility (CSR) is an important part of mining company strategy for practical implementation of the goals of sustainability, transparency, accountablity and good relationships with stakeholders:- investors, employees and communities. A key stakeholder for all mining companies is the local community which is affected by the mining operations. Companies must identify the emerging social and environmental trends, study the interests and concerns of various communities, address their needs and maintain a positive relationship. The CSR programmes of Czech coal mining companies are focused on surrounding community initiatives and sustainable responsible business. Mining in the Czech Republic is subject to strict rules and regulations and supervised by the State Mining Authority. Mining projects undergo rigorous approval procedures which encompass all operational measures at the different planning levels ? such as public participation in the authorisation process for mining projects, the application of the Environmental Impact Assessment Directive, environmental sustainability programmes, innovative solutions and flexible options offered by the mining company. One very important part is the preparation of the mining-technology preconditions and developing the integrated planning process in which all socially and politically relevant subjects in the mining operation surroundings are included. In an in-depth debate, all stakeholders may jointly develop the concept, in accordance with democratic principles. The optimally conducted dialogue process needs broad communication bases, including setting up theme-related joint taskforces, together with good moderation and the highly qualified support of technical experts. Using a case study of Severoceske doly a.s. Chomutov (SD Company) and the Czech Coal Group ? Czech leaders in the extraction of brown coal, this paper aims to examine the community development approaches and the CSR effectiveness of large scale mining companies. This paper brings a review of CSR and other such voluntary initiatives in the mining industry's proactive steps to contribute to societal well-being in a meaningful way. Key studies are provided by the projects ? Region with Better Perspective?, ?Stop Dust for Healthy Brezno Village?, ?Clever Heads for the North? and ?Coal Safari?. CSR issues are managed throughout all stages of the mine operation and beyond, long after the mine closes (e.g. post-closure programmes of new landscape, alternatives for reclamation including generation of lakes in former surface mines, conceptualization of industrial heritage). Communities need to be given the opportunity to help themselves through participation in CSR projects rather than being recipients of financial gifts from the company. A fair balancing of interests is the basis of any successful cooperation.

Aug 1, 2013

By Steve Kral

A near-record crowd of mining history enthusiasts made the trip to Leadville, CO in September to attend the National Mining Hall of Fame and Museum’s 19th induction banquet. Dressed in Victorian garb, black tie tuxedos and formal gowns, the 268 people honored four distinguished men who made a lasting impact on the U.S. mining industry. They joined 188 other inductees. The first induction banquet took place in 1988, with about 500 people attending.

Jan 1, 2007

By L. Echeverri

Research studies have shown that the flow within feedwells displays a vortical structure and high velocities at the locations where standard tangential inlets force its way into the feedwell swirling flow, producing high local shear rates and flow non-uniformities. These hydraulic deficiencies can be attributed to the discrete feeding through a few entrances, usually one or no more than a few tangential feedpipes, which practically project jets into the vortex within the feedwell. The main consequences are unequal flocculation with aggregates subjected to different amounts of shear and a non-uniform discharge from the feedwell. This paper presents results on the application of CFD and small-scale models to develop a new design that overcomes these problems by using an involute shaped inlet that converges around the feedwell. The result is a new feedwell with enhanced hydraulics that perfectly couples with the FLSmidth E-Duc® Feed Dilution system by protecting the flocculated aggregates that have been carefully produced upstream, and that favors uniform sedimentation conditions within the thickener thanks to a uniform discharge, while maintaining a practical and trouble-free geometry with excellent turndown.

Jan 1, 2012

This manual provides instructions for installing, operating, and maintaining a protective canopy on the Joy Mfg. Co. shuttle car. These instructions are based upon actual installations made in the mine on two shuttle cars, model 21SC-2E. The parts list and engineering drawings for the protective canopy are included at the end of the manual. And a discussion of some alternative design concepts is also included. The manual can also be used for retrofitting other shuttle cars with similar protective canopies. Skilled mechanics can determine if the instructions hexein would he applicable to the other shuttle cars and can determine any necessary modifications if they are not.

Jan 1, 1973

By S a m u e l D e a n

The author's written response to previous discussion was presented at the North of England Institute of Mining and Mechanical Engineers general meeting held in Newcastle-upon-Tyne, 8 April 1916, followed by further comments by Hare S. in support of his view that the conditions in English mines were the reason for less satisfactory results being obtained with heading machines and brief comments by Greener T.Y., President

Dec 1, 1916

By N. D. L. Burger

An effective prototype face support system to minimize rockfalls in rockfall-prone mines was developed and patented during a project sponsored by the Mine Health and Safety Council (MHSC). An experimental development model (XDM) roof support unit was developed and evaluated. Mines with rockfall problems in the face areas can use the roof support system to reduce fatalities and injuries in the face area of stopes. The roof support system consists of two similar support units connected to each other via two crank mechanisms. Each unit consists of a headboard supported by a ?wishbone? structure (top and bottom leg). In the first design a threaded bar with struts similar to a scissors jack keeps the legs apart. (In the final version that was field trialed, the threaded bar mechanism was replaced with a hydraulic cylinder). All the components are manufactured from steel. To move the system forward the first support unit is collapsed, the second remaining in the loaded position. The first unit then hangs from the second unit to which it is connected. The first collapsed unit is then manually cranked forward and prestressed. If the required position is still not achieved, the other unit is released and moved forward. The specification for the system was determined and presented at a workshop with industry participants. Different concepts were developed and evaluated against the system specifications. A technology demonstrator was then developed and tested on surface. The technology demonstrator development process included detail design, building and testing of components and subsystems, design reviews and the building and commissioning of the technology demonstrator. The testing of the technology demonstrator was done in a 500-ton hydraulic press, in a mock-up stope and underground. A risk analysis, in which technical, logistical and economic aspects were assessed, was done to determine the critical areas of the system. During the next phase of the project working prototypes were developed for underground tests and evaluation. This process indicated that it was necessary to adjust the system specifications and a redesign was called for. In an iterative process test units were built for purposes of evaluation, specification verification and field trialing. After the successful conclusion of the trials the equipping of a complete production stope started for purposes of integrating the system into the current mining process.

Jan 1, 2008

Base metal skarns have provided most of South KoreaÆs Pb-Zn production since the end of the Korean War, with the bulk of production coming from the Yeonwha group of mines. Currently only the Kumho Zn-Pb mine remains in production, while magnetite skarns are mined as iron ore at the old Yomisan and Ulsan base metal deposits. Base metal skarns within Korea fall into two groups; those hosted in Cambro-Ordovician limestone sequences, situated mainly in sub-basins in the northeast of the peninsula and those hosted within carbonate volcaniclastics of the Cretaceous Gyeongsang Basin, in the southeast. Sulphide mineralisation is dominated by sphalerite, lesser galena, arsenopyrite and pyrrhotite, with subordinate chalcopyrite and molybdenite with Ag-Co credits. Skarns are composed of pyroxene-clinopyroxene-garnet-carbonate-quartz and magnetite, grading into silica-chlorite hornfels. Most of the significant deposits display both pipe-like and stratabound morphology. In the Hwanggang district, a zoned distribution of Ordovician carbonate hosted, polymetallic Mo-W and Zn-Pb-Cu-Ag base metal deposits is observed around the margin of a Cretaceous granite intrusion. Similar polymetallic zoning is recognised in the Sangdong district, where deposits include Sangdong (W), Abisan (Au-As) and Yomisan Northwest (Zn-Mo) and Yomisan Southeast (Zn-Cu-Co), hosted in Ordovician carbonates in proximity to Cretaceous quartz porphyry intrusives. The Taebaeksan district hosts the largest deposits at the Yeonwha group of mines. Although production ceased in 1993, significant resources remain, hosted in Ordovician limestone and dolomite that have been intruded by Cretaceous quartz porphyry dykes. Deposits in the Cretaceous Gyeongsang Basin consist of bedding concordant, vertically stacked base metal skarn mineralisation at several stratigraphic horizons, connected by carbonate-base metal veins with a pipe-like geometry. Evidence such as massive sulphide layers and restricted proximal carbonates suggest mineralisation was initially partly syn-depositional, with both base metals and carbonate venting onto a lake floor, being reconstituted to skarns by later magmatic activity. Skarn mineralisation is universally closely associated with the Cretaceous Bulgugsa Series acid intrusive activity. A common intrusive-structural relationship is recognised at some deposits, with bedding plane and imbricate thrust faulting, introducing felsic intrusives as sills. These intrusions probably introduced the base metals, carbonate, boron, heat and silica, which metasomatically reconstituted the carbonate lithologies to form skarn assemblages. The Korean base metal skarn deposits are regarded as Zn-Pb chimney-manto skarns and display similarities to the Mexican manto type deposits.

Jan 1, 1999

By Tapio Leskinen

"l. IntroductionA reliable sampling system is the basis for an on-stream analyzer. This was realized in Outokumpu company when the development work of the Courier 300 On-Stream X-ray analysis system was started. Because Outokumpu Oy is a mining and mineral processing company, its engineers have been able to thoroughly test sampler prototypes in actual operating situations. The sampler development has been going for several years in close co-operation between company's concentrators, the Institute of Physics and the Instrument Division of Outokumpu Oy. The most active part of the work was done between 1969- 1972. Besides the reliable operation of a sampler special attention was paid to the representatively of the samples taken by the samplers. 2. The Courier 300 Sampling SystemThe sampling system comprises up to fourteen sampling circuits in one Courier analysis system. Each circuit consists of the following components:1. Primary sampler 2. Secondary sampler 3. Cleaner screen 4. Feeding tank5. Sample cell6. Timer-controlled sampler7. Pumps, sumps and pipesSecondary samplers, cleaner screen and feeding tanks are included in the secondary sct1npling system. The sample cells are located in the spectrometer cabinet of the analyzer."

Jan 1, 1976

By William T. Reid

Low-temperature carbonization of coal in Japan served as an important source of liquid fuels during the war. Six plants operating in Japan Proper produced 203,069 KL (53.7 million gallons) of liquid fuel from 1940 until the end of the war in August 1945, while four additional plants in Karafuto and Korea produced 211,943 KL (56.0 million gallons) for a total of 415,012 KL (109.7 million gallons) of liquid products. Semicoke produced in these plants was used for domestic fuel, for gasi- fication in portable gas producers on automotive vehicles, and to replace imported low-volatile bituminous coal in the manufacture of metallurgical coke. Since 1936 one plant had produced more than 300,000 metric tons of semicoke for blending with bituminous coal to form coke, while the total production of semicoke since the beginning of the industry in 1923 is approxi- mately 2,000,000 metric tons. Despite an apparent annual carbonizing capacity of about 2,000,000 metric tons of coal for the entire country, the maximum amount of scmicoke produced during the peak year, 1943, was 468,446 metric tons. The equipment used is primarily of Gorman design. Just before the end of the war, 6 plants using 20 Lurgi carbonizers were operating with a total rated capacity of more than 1,500,000 metric tons of coal per year, while 2 Koppors units had a combined annual rated capacity of 400,000 metric tons of coal. One plant using the Japanese-designed Mimura system was in service but with so much mechanical trouble that its output was small, while in another plant 4 Wanisht carbonizers of Japanese design but based on an early German development were running satisfactorily, and carbonizing about 100,000 metric tons of coal per year. A single installation of 15 American-designed Knowles ovens was operating near Tokyo but was carbonizing pitch for electrode carbon. ..! No true low-temperature process used in Japan could carbonize strongly. caking coals satisfactorily. The Mimura process designed for this purpose was unsuccessful, as was the Shimomura process before it, while the Lurgi, Koppers, and Wanishi systems operated only with noncaking or very weakly caking coals. The Knowles ovens, really a medium-temperature process, could carbonize-caking coal without difficulty...

Feb 1, 1948