Search Documents

The construction, commissioning and operation of a continuous pilot-scale selective agglomeration (oil agglomeration) unit are described. This plant has been used to recover fine coal from an effluent stream that is produced by a jig plant which scalps the coal from a New South Wales (Australia) colliery. The reject slurry is extremely fine (66.5% minus 53 um) and has an ash content of approximately 40%. The pilot plant can treat up to 0.3 tonne/h of this slurry, producing average product ashes as low as 9.1% and tailings ashes greater than 80%. The average yield observed was62%, which corresponded to a recovery of coal material of 88%. The operation of this pilot plant yielded data that enabled an economic assessment of this type of processing to be carried out. This study showed that selective agglomeration is an economically viable process for eliminating the substantial losses of coal to tailings ponds and minimizing consequent disposal and environmental problems. A commercial plant has been constructed and commissioned on the basis of the data obtained from this pilot-scale operation.

Jan 1, 1979

By A C. Carter

The increasing need for alternative energy sources as well as the less clearly perceived but equally increasing demand for non-fuel minerals has resulted in extensive exploitation of near surface deposits. Many such deposits have depleted reserves and mining corporations are increasingly turning their attention to deposits, with thicker overburden, less competent materials, steeper dips and more complex structure. These deposits pose mine layout, geotechnical and equipment problems as well as the need for large outputs to achieve economies of scale. The paper describes the major problems and operational solutions for such deposits using continuous excavation and transport equipment.

Jan 1, 1980

By Waldemar Lindgren

THE following pages present data accepted by many geochemists and geologists regarding the succession of minerals and the temperatures of formation in ore deposits affiliated with igneous rocks. They also present the individual views of the author on the composition of the solutions that were active and on the mode of deposition. He does not regard these views as speculations or hypotheses but as forming a well motivated and consistent theory. It is not certain, however, that all investigators will subscribe to them.

Jan 1, 1936

By Loui Geoffroy, Philippe Gaultier, Martin Piotte, Claude Coache, André Drouin

"Automatic driving at high speed of an underground truck was tested at Brunswick mine in September 1995. Modifications to the truck included: a remote interface to control actuators, front and back video cameras to follow a roof mounted optical guide and proportional hydraulic controls on the steering.The mathematical model of the hydraulic system was adjusted using least square regression. The steering data, used in calculating the regression parameters, were acquired from the moving truck. The automatic steering control used three measured variables: lateral deviation, angular deviation and steering angle. Lateral deviations are obtained using the cameras, which are in continuous view of the guide, while steering angles are acquired from an extensiometer placed at the articulation point of the vehicle. Gain scheduling was used to compensate for vehicle speed and available hydraulic flow. Non-linear characteristics of the modeled hydraulic system were offset using open loop compensation.Speeds up to 23 km/h in forward direction and 13 km/h in reverse were achieved deviaduring continuous testing along one of the mine’s production drifts. Proportional steering was essential in achieving high speeds, as it enabled more precise positioning of the vehicle’s steering direction while reducing the abuses on cylinder and cylinder pins via diminished oscillations about the optical guide at high speeds."

Jan 1, 1997

Mining Systems and Technology - Synchronous Electric Drives for Grinding Mills

Sep 13, 2010

By C. H. Johnson

The Big Jim mine of the United Eastern Mining Co. is at Oatman, Mohave County, Ariz. Oatman is in the foothills on the western side of the Black Mountains, at an elevation of about 3,000 feet. It is on a paved highway about 30 miles west of Kingman, the principal distributing; center for mining supplies in the district, and 25 miles from Topock, en the Colorado River. Both latter towns are stations on the Santa Fe Railroad; Oatman has no roil connection. Mining conditions are typical of western Arizona; water is scarce, no mine timber is available locally, and the winters arc mild and the summers hot. The supply of a killed labor is usually adequate, but in 1933-34 it w not more than sufficient for the restricted operations. Wages have been $4.00 to $4.50 for miners. Electric power was supplied from Kingman and cost about 2.6 cents per kilowatt-hour.

Jan 1, 1935

By R. L. Whiting, H. J. Ramey

The basic study from which this paper was prepared was started as the result of the growing need throughout the world for increasing quantities of energy in all forms. Quite obviously, natural forms of energy that are readily available at low development cost are those in greatest demand. The underdeveloped countries — and particularly those having little or no petroleum resources — are the countries in which the most interest is being shown in the newer energy sources. One of the least expensive energy sources is natural geothermal steam.'-* Although this form of energy has been recognized for centuries, it has been only during the past 20 years that serious efforts have been made to harness it. Natural geothermal steam energy in Italy, New Zealand, Mexico, Japan, and California is now being produced through wells to drive turbines and generate electricity. Further, active exploration for natural geothermal steam is being conducted in Hawaii, Fiji, Taiwan, Chile, Russia, Greece, and Katanga. It is surprising to find that most geothermal steam exploration is in the "steam seep" stage. That is, surface studies are made and exploratory wells are drilled in the general area of steam seeps. However, in the larger geothermal steam areas, there have been efforts to apply the most modern geological and reservoir engineering principles in order to define the reservoir parameters, particularly those relating to estimates of reserves and future productivity. This paper is concerned with the development of appropriate equations and techniques to facilitate these estimates. Production of natural steam or hot water presents problems different from those experienced in the production of oil and gas. For example, steam or hot water systems may be essentially single-component systems, while hydrocarbon systems are most frequently multicomponent fluid systems. Heat effects are much larger for water than for hydrocarbon systems; and the natural steam production may or may not be isothermal, while production of petroleum reservoirs is considered normally to be isothermal. Petroleum reservoir engineering principles may be applied to natural steam or hot water reservoirs if the inherent differences in the systems are considered. The basic considerations involved in geothermal steam reservoir engineering are: thermodynamics, physical and thermal properties of water, materials and energy balances, fluid influx, and performance matching and predicting. Thermodynamics Fig. 1 is a pressure-temperature diagram for the liquid-vapor region for pure water, showing the critical point and five other points representing possible initial conditions for a geothermal steam reservoir. To generate a physical appreciation for the mechanics of natural steam production, it is helpful to consider

Jan 1, 1970

By R. H. Wallis

Weighted moving-average contour maps have been constructed for molybdenum, copper and zinc using 7850 stream-sediment samples from 5430 square miles (14,063 sq. kms) of south-central British Columbia. Regional trends for molybdenum and zinc are northeast, north and northwest and those for copper are north and northwest. These trends are interrupted by zones markedly low in metals . The metal-rich trends cross rocks of different lithology and age and thus appear to be structurally controlled. The northeast trend may have exerted control on metal distribution at two different times.

Jan 1, 1978

By P. J. Hancox

Heavy mineral deposits have been known from Liberia since the1950s from both river and beach placers. The heavy mineral content of beach sands ranges between 28?62% and the suite includes ilmenite, rutile, zircon and magnetite. These occur together with kyanite, sillimanite, staurolite and garnet. The average ilmenite content is 82% with minor zircon (11%), rutile (6%) and monazite (1%). The ilmenite is, however, of poor quality with haematite intergrowths and a titanium content ranging from10?42.4% (average ±25% TiO2). The amounts of rutile and zircon, while of suitable quality, have also previously been deemed too low for economic exploitation.

Jan 1, 2000

By K. Huessener

INTRODUCTION THIS paper attempts a survey of the principles involved in the com¬bustion of blast-furnace gas in boilers and stoves. I do not expect to be able to give much information which is actually new, since the laws and methods of calculation pertaining to this problem are contained in a number of handbooks; but, so far as I am aware, they have nowhere been treated exclusively with reference to this one problem of gas economy. The road which I follow is less that of strictly scientific research than that of the practical engineer, faced by operation problems which require a. quick solution by easily accessible means without a prolonged search in scientific handbooks. For this purpose I give a number of tables and diagrams, as well as the results of many years' practical working experience as combustion engineer, which I trust will prove useful to my readers. HISTORICAL Considering the tremendous efforts made during the last 15 years to increase the efficiency of all kinds of power plants, it is highly surprising that until a comparatively very recent period, progress in the economical combustion of blast-furnace gas has been so slow. The explanation generally put forth, that fuel has been so cheap that it was hardly worth while to bother about this economy, will not hold good, for the greatest trouble was taken to improve the combustion of coal and to reduce the consumption of steam. The most plausible explanation appears to be the general impression, held as an accepted fact, that gas, especially hot, uncleaned, blast-furnace gas, was not a good boiler fuel. Many managers of high repute had tried unsuccessfully to improve the conditions of its use, and the dictum went forth that efficiencies of over 60 per cent., particularly with high loads, were impossible. This was the situation not only in the United States, with very cheap fuel, but also in Europe, where fuel prices are twice and three times as high.

Jan 2, 1916

By D. W. Loucks

There is plenty of evidence to indicate that at least one of man's chief interests in life is to make himself as comfortable as possible. If you doubt this, just watch the fellow next to you for the next half hour trying to find the most comfortable position that a hard chair has to offer. Comfort, however, does not always mean an easy chair. To some, it may mean a wealth of money: to another, freedom from worry. But to most of us, it means first of all a comfortable atmosphere in which to live, and to a great many of us it probably also means freedom from that annoying task of firing the furnace. Today more than ever before, automatic heat is one improvement that is placed high on everyone's list. Perhaps this is because automatic heating is becoming relatively cheaper. Perhaps it is because of a good publicity campaign on the part of the oil and gas men or maybe it is just that we are getting lazier day by day. At any rate, almost every issue of Better Homes and Gardens, House Beautiful, or your other favorite home magazine carries an article extolling the virtues of this or that automatic heating system.

Jan 1, 1949

Mining education has received almost continuous discussion since its inception and most people engaged in the mining industry and in mining education feel at some time the urge and necessity to express their views. This paper is not a comprehensive survey of past and present practices and accepted principles, but a personal opinion of the form mining education should take at university level. It is expressed because of a dissatisfaction with the existing courses offered to students. It is hoped to provoke discussionand bring forth guidance to those engaged in mining education. After all, students spend four or five years at a university and it is desirable that the graduate should be something more than just those many years older at the end of his course.POST GRADUATE EMPLOYMENTThe first problem confronting the university should, be to discover what the mining industry wants and expects or graduates. This must influence the university course and yet universities have done little to seek this information, and if suggestions have been offered by industry; universities appear to have made little use of them. University mining curricula are basically what they were 50, 100 and even 200 years ago. (See Appendix.) Whether this reflects the unchanging problems of mining the wisdom of early professors, the conservatism of subsequent professors or inability to apprectate necessity for changes, is debatable.Unfortunately there is no uniformity in the type of employment offered to new graduates: Some mining...

Jan 1, 1959

By M. I. Brittan

Cyanide leaching of two West African gold ores was studied in multiple laboratories to provide process-engineering data for plant design purposes. Unusually slow leach extraction kinetics were observed using routine cyanide leach test procedures with pregnant solution monitoring. Carbon-in-leach testing, however, showed normal rapid kinetic behavior, with the same ultimate gold extractions being reached in much shorter elapsed times. Kinetic curves based on washed solids assays also exhibited more typical leaching characteristics. The results bore all the hallmarks of some equilibrium inhibition of the leaching. It was surmised that ore gangue components were responsible for weakly adsorbing gold-cyanide complex reaction product, thereby holding up soluble gold in the solid phase. The term ?preg-borrowing? was coined to describe the reversible phenomenon and distinguish it from irreversible preg-robbing. The two ores investigated may represent an extreme form of a more general effect that in most instances might pass unnoticed. The effect can lead to misinterpretation of kinetic leach curve data and underestimation of calculated ore head grades.

Jan 1, 2008

By H. Copur

Experimental studies for quantification of force and brittleness indices relevant to rock cutting performance are presented. A simple interpretation method is developed, which quantifies the force-penetration response obtained from indentation tests. Basic parameters of the quantification are force increment and decrementrates, force increment and decrement periods, and number of increment and decrement data points. Blocks of eleven different rock samples were collected from different operating mines in Turkey and subjected to indentation tests to calculate the indices. The samples included harzburgite, serpentinite, trona, limestone, claystone, two different sandstone samples, siltstone and three different chromite ore samples. The concept was validated by a set of full-scale linear cutting tests using a conical cutter for measuring the cutting performance in relieved and unrelieved conditions, i.e. cutter forces, specific energy, size distribution of rock cuttings. The rock cuttings were sieved to determine coarseness index, indicates coarse chip generation characteristics, and size distribution. The force index is moderately correlated with the cutting performance and mechanical properties of the rocks, and poorly correlated with the coarseness index and size distribution of cuttings. A general and moderate trend is observed between the brittleness index and the coarseness index, cutting performance for unrelieved cutting conditions and mechanical properties of the rocks. However, additional data is required to fill the data gaps and to potentially establish relationship between the brittleness index and all other parameters.

Jan 1, 2003

By Geoffrey Birch

A skilled and efficient workforce is a pre-requisite for the success of modern construction companies. The drive for improved performance, innovation and best value must be matched by the enhanced skills of the construction personnel. Training has been accepted as one of the essential cost effective elements to achieve these goals. The foundation industry demands particular specialist skills and requires focused training for its dedicated operatives. The introduction and development of specific training qualifications for the foundation sector is providing significant benefits.

Jan 1, 2000

By A. H. Cronk

This paper is one of a series being prepared by the United States Bureau of Mines on mining methods and costs in the different mining districts. The mining methods described in this paper are employed by one of the large mines in the Illinois fluorspar district. The mine is located at Rosiclare, Ill., and shipments are made over the Illinois Central Railroad: and by barge on the Ohio River.

Jan 1, 1930

Coal cleat and faulting influence failure, gas release, and choice of preferred mining directions, locations, and sequences. Unfortunately soil and younger rock cover restrict direct mapping of these structures ahead of mining operations. Aerial photographs of cover contain indirect indications of concealed structures in arrays of linear photostructures. These arrays are commonly too complex for interpretation by simple visual inspection.Analytical techniques applicable to complex arrays are illustrated for a covered part of the Galilee Coal Basin, Queensland. These techniques are: optical determination of sets in arrays of photostructures; correlation of these sets with sub-surface structures; filtering of m-rays for particular sets; detection of anomalies associated with concealed structures in the density distributions of particular sets; fitting filtered arrays to trajectories; correlation of trajectories with the regional directional variations of concealed structures; contouring of ratios of sets to discriminate anomalies associated with concealed fractures and variations in the total and bed thicknesses of cover; kinematic and dynamic inference on the basis of fracture-trace angular and spatial relationships.

Jan 1, 1979

THE flotation plant at Mount Lyell was erected, primarily, for the treatment of ore from the Lyell Comstock mine. These workings are situated over a mile in a direct line north of the North Mount Lyell mine, and are connected with the Reduction Work at Queenstown by a 2-ft. gauge steel tramway via the Queen River valley a distance of 7 miles. The property was purchased from the Mount Lyell Comstock Copper Co. After the disastrous fire in the North Mount Lyell mine in October, 1912, steps were immediately taken to make Lyell Comstock ore available for treatment, in order to relieve distress caused by any prolonged stoppage of work, and subsequently 13,032 tons of ore, averaging 3.38 %copper, 0.28 oz. silver, and 0.034 oz. gold; were smelted. When operations were resumed at the North Mount Lyell mine, it was evident that there was no economic advantage in smelting Lyell Comstock ore as compared with the higher value North Mount Lyell ore, which was also a better flux for the Mount Lyell pyrites, and that the future of the Lyell Comstock ore depended upon cheap mining and successful concentration of the ore. Therefore, extensive trenching and diamond-drilling was carried out, and a sufficiently large quantity of ore proved available for cheap extraction by open-cut methods. At the same time bulk tests by flotation were carried out at the Minerals Separation testing plant in Melbourne on different classes of ore from the Mount Lyell Comstock mine proper, followed by laboratory tests at Queenstown on all classes of ore available. All these tests demonstrated that the ore was amenable to the process, provided that it was ground finely enough. Plant erection was delayed by the general dislocation of business at the outbreak of war, but finally it became...

Jan 1, 1920

By J. H. Zietsman

It has previously been observed that industrial high-titania slags display a compositional invariance, remaining close to stoichio-metric M3O5. The present study focuses on this invariance and the phenomena which may cause it. The invariance was studied using thermochemical calculations and a mechanism is proposed for the observed behaviour. The mechanism suggests that a combination of thermochemical equilibrium and transient slag solidification and melting results in the observed compositional invariance. The proposed mechanism provides new insights and prompts questions about other mechanisms in the smelting process.

Jan 1, 2004

By J. Danoczi

Specially designed X-ray machines are used extensively on diamond mines for the recovery of diamonds from ores. These machines are extremely expensive and, at present, there are no reliable methods of determining if the equipment is performing efficiently. The objective of this work was to manufacture translucent X-ray diamond simulants, which would emit varying but known luminescence signals when exposed to X-rays. These X-ray diamond simulants could then be used to determine the efficiency of diamond recovery operations.

Jan 1, 2008