Search Documents

The Pinto Valley, Arizona, plant of Cities Service Company is one of the newest copper producers in the United States, having started production in 1975. It is located a few miles west of Miami, Arizona, on the site of the Castle Dome Mine, a World War II operation which was shut down and its mill later moved and renamed the Copper Cities plant. The Pinto Valley concentrator uses six 18 ft (5. 5 m) diameter by 21 ft (6.4 m) long, 4000 hp, single-stage ball mills, taking crushed ore from four 7 ft (2. 13 m) standard and eight 7 ft shorthead crushers. It has a design capacity of 40,000 stpd but has higher tonnage capability for an expanded concentrator. The copper porphyry-ore is mined by two 15 yd and one 20 yd shovels (11.5 and 15.3 cu m) and is transported to the primary crusher by 150-ton trucks. The dump pocket is relatively shallow (14 ft or 4. 27 m deep); and because of the width necessary for the 150-ton trucks, it was designed to use the ore itself instead of manganese steel as an abrasion- resistant lining, although a heavy steel cap protects the dump pocket top edge. The pocket has a capacity of 300 tons of ore. Water sprays under the dumping positions direct a fog toward the truck being dumped for excellent dust control. Breaking of oversize is done by a hydraulic impact breaker mounted on a hydraulically operated articulated arm situated at the side of the dump pocket. Again because of the shallow pocket, no splitter is used to protect the spider of the 60 in. by 89 in. Traylor gyratory crusher, which is equipped with a hydroset mechanism. Crushed ore at 8 in. (203 mm) drops into the 360 st surge chamber lined with AR plate and then is fed directly to the 60 in. (1.52 m) stock- pile conveyor by an 84 in. by 20 ft (2. 13 m by 6.1 m) four-speed apron feeder at a rate of up to 4000 stph. Early in 1977, Cities Service will replace the four -speed electric drive with a hydraulic pump and motor with infinitely variable speed. They are also studying the replacement of the apron feeder with an 8 ft wide (2.44 m) belt feeder similar to those at Similkameen and Palabora. Peak crushing capacity would then be increased to 5000 stph. The AR plate in the crushed ore pocket was installed in large, rectangular sheets which required much less embedded metal to hold it in place than would the more conventional, smaller arid square pieces of cast manganese steel. For duty in the crushed ore pocket, where wear is not severe, the AR plate is a satisfactory material. The new Palabora Figure-8 crusher also uses this design.

Jan 1, 1978

By M. Gomo, L. S. Mokhahlane

"Underground coal gasification (UCG) is an unconventional mining method that converts coal in situ into a fuel gas that can be used for electricity generation. Residue products from UCG have the potential to leach into surrounding groundwaters. The geochemistry and leaching dynamics of these products are explored in this study. The products include char, ash, and the heat-affected zone in the surrounding rocks. Core samples from the pilot plant at Majuba are the first ever to be recovered from a UCG cavity in Africa, and they give key insights into the geochemistry of the gasification zone. Mineralogical and chemical analyses were performed on the samples, and acid-base accounting (ABA) was used to predict the acid-producing capacity of the gasification zone, particularly for char samples. Some of the char contained pyrite, although not all samples were acid-producing as determined by the ABA analysis. The ABA results showed that some of the unburned coal has moderate levels of sulphur, which could be the driving medium for acidic conditions. The ABA analysis indicated that water in contact with the gasification zone would eventually have a pH lower than 7, which could lead to acid rock drainage. These results form part of a preliminary investigation into the geochemistry of the reaction zone, post gasification. IntroductionUnderground coal gasification (UCG) is an unconventional mining method that converts coal in situ into a fuel gas that can be used for industrial purposes, including electricity generation. The gasification process leads to the formation of a cavity composed of char, rubble, and void space (Bhutto, Bazmi, and Zahedi, 2013). Residue products from UCG have the potential to leach into groundwater. These products include char (devolatilized coal), which can generate acid rock drainage (ARD). ARD is caused by the oxidation of sulphide minerals, which acidifies the leachate, thus increasing the solubility of some environmentally toxic metals (As, Cd, Hg, Pb, Zn, etc.) (Bouzahzah et al., 2015).The main source of ARD is oxidation of sulphide-bearing minerals due to interactions with oxygen, water, and microorganisms (Simate and Ndlovu, 2014; Kefeni, Msagati, and Mamba, 2017; Bouzahzah et al., 2015). Although ARD occurs naturally, it can be enhanced by mining activities that escalate exposure of sulphide minerals to water, air, and bacteria (Simate and Ndlovu, 2014). At the Majuba pilot plant, the unburned coal remaining in the cavity has been in contact with groundwater since the gasifier was shut down in 2013. It is possible that in a commercial UCG plant, most of the coal will be consumed and no unburnt coal will be left in the cavity. Most of the sulphur will be converted to H2S during the gasification process and transported with the syngas to surface, where it can be removed and captured as elemental sulphur."

Oct 1, 2018

By G. R. Morin, A. R. Leggett

"In 2010, closure of the Kidd metallurgical plants along with structural changes to the historical ratios of payable metals led to a review of the operating targets at the Kidd concentrator. Previous operating data indicated that there was potential for significant revenue improvements by lowering the copper concentrate grade. An extended plant trial was carried out in 2011 to quantify the revenue impact of lowering the copper concentrate grade from 27% to 25% Cu, as well as identifying the lower practical grade limit. Analysis of plant trial results indicated that the process change increased net concentrate revenue by $2 M to $3 M per year at current metal prices. Increased revenue was primarily associated with higher silver recovery to the copper concentrate while the marginally improved copper recovery was essentially offset by increased zinc losses and concentrate treatment and freight charges.Details of the plant test work results are discussed in this paper along with the financial analysis of the revenue improvements. Key areas covered are major revenue components of the concentrate contracts, validation of revenue improvements through plant testing and sensitivity of the improvements to market and plant variables.INTRODUCTIONThe Xstrata Copper Kidd concentrator commenced operations in 1966 treating ore from the nearby Kidd volcanogenic massive sulphide deposit in Timmins, Ontario (Thompson, Amsden, & Chapman, 1978). Over the years, up to four separate grinding-flotation divisions were in operation with throughput rates peaking at 4.5 million tonnes per year of ore in the mid 1980’s (Kelebek & Francis, 1998). As the mine production decreased and grinding throughput increased operations were gradually cut back and since 1998 two grinding-flotation divisions have been in operation treating Kidd mine ore. One of the idled divisions has been intermittently used for custom milling operations, most recently the Ni/Cu Montcalm deposit, which was milled from 2004 to 2009. Current budget throughput rates, limited by mine production, are 2.4 million tonnes per year of ore grading 1.7% Cu, 4.3% Zn and 55 g/mt Ag. Concentrate production rates are 150,000 tonnes per year of copper concentrate and 155,000 tonnes per year of zinc concentrate. The Kidd mine is the deepest base metal mine in the world with mining operations down to 9600 ft.In 2010 the copper and zinc plants at the Kidd metallurgical site, which previously treated the concentrate production from the Kidd concentrator, ceased operation due to a variety of economic and market factors. Following the metallurgical plant closures the Kidd concentrator products were shipped off site for treatment. The majority of the copper concentrate is now processed at the Xstrata Copper Horne smelter in Rouyn-Noranda, Quebec with the majority of the zinc concentrate processed at Canadian Electrolytic Zinc Ltd. in Valleyfield, Quebec."

Jan 1, 2013

By Ralph H. Sweetser

N Greenup and Carter counties, in the northeastern part of Kentucky, are the remains of many old charcoal furnaces built and operated during the period from 1818 to 1892. They were all included in what was called the Hanging Rock district. In the summer of 1930 I visited ten of these old blast furnaces, as follows:

Jan 1, 1931

By C. Sima, M. Legoabe

Keywords: Pyrometallurgy, furnace, platinum Mortimer Smelter is one of the three smelting operations in the Anglo Platinum Group. It is located in the Limpopo Province, approximately 100 km north of Rustenburg, and approximately 15 km west of Northam. The smelter operation is the smallest of the three smelting operations in the group, with a smelting capacity of 170 kt/annum. The operation consists of a Larox filtration plant, a Drytech flash drying plant, a modified Elkem / Hatch 19.5 MVA furnace, and a 60 t/h matte crushing plant. The operation does not convert its furnace matte, and hence the final sulphide rich matte is transported to and processed further at the Anglo Platinum Converting Process (ACP) within the Waterval Smelter Complex in Rustenburg. Furnace slag is granulated, and processed through a slag mill, or transported to a slag dump.

Jan 1, 2006

By John Watson, Tom Treleaven

This guide presents nur-nerous patterns that provide 8 millisecond separations between initiated charges. The guide is tabulated in seven sections to provide Quick reference by number of decks or bunch blasting. The pattern IS presented in the section where the highe!$ number of decks works. It should be noted that patterns applicable to multipledackshwtings are alsoapplicsblefor fewer decks.

Jan 1, 1995

By H. Zhu, Y. Sato, O. Takeda, K. Nakano

Recycling of rare earth magnet wastes is essential to insure the stable supply of rare earth resources. For the development of a novel recycling process, the removal of rare earth oxide from an off-spec alloy magnet was investigated by melting the alloy magnet at 1503 K together with fluoride flux, LiF-50 mol% NdF3 and LiF-?25 mol% NdF3-25 mol% DyF3. After melting, the separation of magnet alloy from the fluoride flux was achieved, and neither suspension of alloy in the flux nor suspension of flux in the alloy was observed. Oxygen concentration in the alloy decreased from 5000 mass-ppm to 160 mass-ppm by utilizing 1.5 times of equivalent amount of flux needed to completely dissolve the oxide. The investigated process is suitable for mildly contaminated waste such as a used (end-of-life) magnet because of its simplicity, low energy consumption and small limitation on location for operation.

Jan 1, 2014

By R. Carson Dalzell

The use of nuclear fission for chemical process heat offers the special advantage of high temperature, limited only by materials of construction. The process heat may be supplied economically at elevated pressures, since no compression of combustion air is required. For the initial effort in developing a high-temperature reactor, the indirect cycle, using helium as the heat-transfer medium, was chosen. The major problems are the design of high-temperature fuel elements, construction of an exchanger to transfer heat to process streams in the range of 2,500° F., and development of compressors capable of recycling helium at 1,000° F. and above. A conceptual design of a nuclear reactor to furnish process heat for coal gasification has been made. Spherical fuel elements utilizing a graphite structure, impregnated with uranium carbide fuel, were chosen, as spheres offer the possibility of easier loading and unloading of the reactor. Calculations of pressure drop and gas-pumping power for the system are included.

Jan 1, 1959

By Gary E. Sherman

This report presents a Bureau of Mines study on the cost of mine permitting and compliance with environmental regulations in Alaska. It discusses permitting requirements and procedures for placer and lode mines. Placer miners must comply with recently established (1988) water quality regulations and effluent treatment requirements. To estimate the impact differing treatment options (no recycle, 100% recycling, and flocculation) have on a placer mine's rate of return, three models (1,500, 1,000, and 500 yd3/d) were simulated. Rates of return for these models show a marked decrease as effluent treatment is increased. The incremental increase in operating cost from one treatment option to the next is relatively small; however the opportunity cost of lost production if' significant and accounts for the decreasing rate of return with increased effluent treatment. Lode mines face greater costs for permitting and compliance than similarly sized placer mines as a result of the impact of the operation. Direct permitting costs for lode mines range from 2 to 6% of total project cost, with 4% the most common figure cited by industry. Total costs for permitting and compliance are approximately double those for permitting. Indirect costs associated with compliance include mitigation, monitoring, and reclamation.

Jan 1, 1991

Jan 1, 1970

By K. G. Wheeland, J. E. Dutrizac, M. Wasserlauf, A. A. Condy

Numerous processes for the treatment of thiosalts in base metal milling effluents have been examined in the past decade. Flowsheets for thirteen processes are outlined, and cost estimates are presented for a base case of a 720 mi/h effluent flow containing 1400 mg/L thiosalts. The processes are ranked on the basis of Numerous processes for the treatment of thiosalts in base metal milling effluents have been examined in the past decade. Flowsheets for thirteen processes are outlined, and cost estimates are presented for a base case of a 720 mi/h effluent flow containing 1400 mg/L thiosalts. The processes are ranked on the basis of

Jan 1, 1988

By S. V. Rungan

Since 1994, South Africa has been the subject of international attention, especially in regard to its transformation initiatives, which aim to redress the post-apartheid imbalances. Mining, as a major employer and one of the major industries in South Africa, has been the focus of the government?s Black Economic Empowerment initiative with the introduction of the Minerals and Petroleum Resources Development Act and the Broad?Based Socio?Economic Empowerment Charter for the South African Mining Industry. The historical background to South Africa?s transformation and the role of the mining industry are pivotal to an appreciation of certain aspects of the Minerals and Petroleum Resources Development Act and the Broad?Based Socio?Economic Empowerment Charter for the South African Mining Industry. The issues around Black Economic Empowerment and the enabling of a smooth transition to the South African mining industry of the future are explored in this paper.

Jan 1, 2005

By S SSdbom

A comparison was made between chemical analysis and ocular mineral/rock classification in health-based risk assessment of historical mine waste produced between 1625 and 1975. Large parts of the mine waste are heavily weathered and secondary minerals are abundant. The field was divided into several areas from where composite samples were collected. Seventy-five mine waste samples were selected for chemical analysis (As, Cd, Co, Cr, Cu, Hg, Ni, Pb, V and Zn) and ocular mineral/rock classification (silicate, mica, granite/pegmatite, carbonate, iron oxide ore, sulfide ore, distribution between chalcopyrite, sphalerite and galena and distribution between pyrite and pyrrhotite). The waste has been produced in conjunction with mining a complex sulfidic ore with increasing iron oxide content (mainly magnetite) towards the northern part of the field. Elevated concentrations were found for Cd (average 26 mg/kg dw), Cu (average 3500 mg/kg dw), Pb (average 4100 mg/kg dw) and Zn (average 11 000 mg/kg dw). Large differences between average and median values indicated that the data was not normally distributed, ie the metals occur as discrete minerals (eg chalcopyrite, galena and sphalerite). The ocular classification indicated low carbonate content, chalcopyrite dominating over sphalerite and galena in most samples and an even distribution between pyrite and pyrrhotite. Both analytical and ocular mineral/rock classification data were combined into a common matrix that was evaluated using multivariate statistics. Principal component analysis (PCA) showed, for instance, that chromium and vanadium were mostly associated with harder minerals and rocks. PCA also indicated that a similar graphical picture could be obtained for chemical data and ocular mineral/rock classification data, respectively. The comparison indicates that ocular mineral/rock classification can replace or at least reduce the numbers of chemical analysis in health- based risk assessment of historical mine waste.

Jan 1, 2008

By W. C. PAGE

AS the pioneer operation treating the mixed lead- zinc-iron ores from the district tributary to the Salt Lake Valley, the International Smelting Co.'s plant has offered an extremely interesting and instructive opportunity to study some phases of this problem. Basically, there were two main reason for our attempting to work out a successful operation for the separation and concentration of the values contained in the rather widespread deposits of these so- called lead-zinc ores. In the first place, the time was ripe and demanded some method of curtailing the economic waste resulting from the costs of past and present practice of smelting ores of this character, or rather, those ores which could stand the charges inherent with smelting them. Secondly, but rather primarily with us, we believe that such a solution would greatly in- crease in general the production of lead in the district tributary to the Salt Lake Valley. It is generally known that there were and are three relatively large lead smelting plants in the Salt Lake Valley and the decreasing production of correspondingly clean lead ores was not efficient to justify the existence of all three. We could not hope for better lead smelting metallurgy nor more efficient business management than was being practised, so the only prospect was to at- tempt to work out some way to increase the primary production and thus widen the scope of operations.

Jan 1, 1926

By Arturo Ressi di Cervia

From the times when men in lacustrine environments drove wooden piles into the mud to elevate their dwellings, until the beginning of the twentieth century builders reacted to the conditions found in the location of their proposed structures by attempting to distribute their loads in ways that could be supported by the foundation's soils; or, if those were unsuitable, by moving the structure, whenever possible. While many major structures were built on stable ground (the pyramids were founded on rock), others were built on [ ]

Jan 1, 2000

By Warder A. Shaver

INTRODUCTION Mine No. 95 of the Consolidation Coal Co., a divi¬sion of Continental Oil Co., is located in Shinnston, WV. Mine No. 95 was opened in January 1967 and has been operating continuously since that time. The mine has 544 hourly and salaried employees. In 1974 this mine was the largest coal producer in West Virginia. Opera¬tions include two longwall sections and eight Marietta Borer continuous miners. Originally there were also two Jeffrey Heliminer continuous miners, but use of these was discontinued in June 1978. Production averages 12 727 t/d (14,000 stpd). Two portals now service the mine with a third portal proposed for 1978. GEOLOGY Mining takes place in the Pittsburgh coal seam which dips 0.04 rad (21h°) northwest. The working seam is steam coal with an average height of 2.2 m (86 in.). Immediately above the seam, the overburden is com¬posed of 6.1 m (20 ft) of shales followed by 6.1 m (20 ft) of weak sandstone and 51.8 (170 ft) of shaley limestone. The shale weathers when exposed to mois¬ture. Surface water has been a problem due to a fire¬clay floor which turns to paste when mixed with water. GENERAL DESCRIPTION The present mining plan for Consol's No. 95 mine has a proposed life of 35 to 40 years. One set of main headings has been driven in the north direction and one set in a western direction. These are the areas in which the majority of the virgin coal lies. The panels are driven off of the mains at 2134 to 3048-m (7,000 to 10,000-ft) intervals. The continuous mining sections are set up 133 x 610 m (600 x 2000 ft). Longwall sections are 259 x 1220 m (850 x 7000 ft). All of these mining sections are retreating uphill. Development is with continuous miners. A Marietta Borer miner is used for the main development work. These miners cut 4.1 m (13 ft 6 in.) wide and 2.1 m (7 ft) high, leaving an arch cut. Along with the arch, a 152.4-mm (6-in.) thick layer of roof coal is left in place to protect the roof from weathering. The combi¬nation of the self-supporting arch and the roof coal al¬lows the entries to be driven 30.5 m (100 ft) without bolting. Full bolting, however, is carried outby the last open crosscut. This bolting is done on 1.5 x 1.5-m (5 x 5-ft) centers using 1.5-m (5-ft) long roof bolts with tandem anchors and 152.4-mm (6-in.) steel washer plates. When needed, crib blocks with a 50.4-mm (2-in.) drill hole are used as supplemental supports. Three-hole steel channel with the ends curved down¬ward to conform to the borer arch may also be used. In the mining sections, a 14 BU loader is used be¬hind the Marietta miner to load two Torkar shuttle cars. These haul to Long-Airdox feeder breakers which load onto a 1.07-m (42-in.) wide conveyor belt. With the exception of the shuttle cars, which use 275-V d-c power, the face equipment operates on 550-V a-c power. The main power line is 7200 V ac. The same loading and hauling equipment is used with the Marietta Borer miner for driving both panel and development entries. In the retreat sections, the same equipment with the exception of the miner is utilized. Because of the advantage of a variable cutting hight, Jeffrey Heliminer ripper-type continuous miners were employed in these retreat sections. For longwall mining the first unit uses an Eickoff EDW 300-L double-drum ranging shearer. Drum di¬ameter is 1.69 m (66 in.) with a drum rotation speed of 45 rpm. The drum is equipped with 48 Carmet 34-L-1 bits. The 300-kW (400-hp) motor operates on 1000 V. Tramming of the shearer head is done through a hydraulically driven 26-mm wide chain. Maximum cutting speed is 7.93 m/min (26 fpm), and maximum tram speed is 12.8 m/min (42 fpm) with an average cutting speed of 3.66 m/min (12 fpm). Web cutting depth is 762 mm (30 in.) and the cutting height is 2.13 m (7 ft). The conveyor width is 686 mm (27 in.). It uses a single chain, 26 mm thick, with flights on 0.91-m (3-ft) spacing. The face conveyor speed is 64.3 m/min (211 fpm) when driven by two 112-kW (150-hp) 1000-V Louis Allis motors through torque convertors. The roof support used is Gullick Dobson chocks [6-legged 77.3 t (85 st) per leg, 463.6 t (510 st) total capacity] with double-acting leg jacks. The hydraulic pressure for the legs is 13.8 MPa (2000 psi), and the hydraulic pressure for rams is 6.8 MPa (1000 psi). The yield valves are set at 57.8 MPa (8500 psi). Each chock weighs 4.09 t (4.5 st). The stage loader is an Eickoff drive, with a 68-kW (90-hp), (00-V Reliance motor. A 26-mm thick single strand chain with flights on 0.6-m (2-ft) centers runs at 75.89 m/min (249 fpm). The stage loader is self-advancing and is connected to the belt tail piece with a special fifth wheel attachment so that the stage loader can advance and guide the tail piece. The hydraulic pressure for the roof support is supplied by two 45-kW (60-hp) Reliance motors op¬erating on 699 V, with 1.26 L/s (20 gpm) constant volume Gullick hydraulic pumps. Each pump services alternate chocks, with the two pressure lines connected at the tailgate by 25.4-mm (1-in.) hydraulic hoses, rated at 27.21 MPa (4000 psi). The 6.8 MPa (1000 psi) pressure rams advance is supplied by a 45-kW (60-hp), 600-V Reliance motor and a 1.26-L/s (20-gpm) con¬stant volume Gullick pump. Return lines are 35.5-mm (1.4-in.) diam hydraulic hoses with rated capacity of 27.21 MPa (4000 psi). The fluid used in the hydraulic system consists of 95% water and 5% Hy-chock fire resistant water soluble oil. Water is stored and mixed in a 6096-L (2000-gal) track-mounted tank and goes to a 655-L (180-gal) reservoir at the pump. The belt conveyor structure is 1.07 m (42 in.) wide with 0.47 rad (27°) idlers, bottom stands located on 3.05-m (10-ft) centers, top stands on 1.5-m (5-ft) centers, and is supported on a 19-mm (3/4-in.) diam

Jan 1, 1982

By Joel T. Werner

Tire costs represent one of the highest controllable costs in open-pit mining, accounting for approximately 10% of mining costs. Tire monitoring technology has evolved rapidly in recent years and is emerging as a viable tool for extending tire life and reducing costs. The majority of the major tire manufacturers and several independent companies are in various stages of developing monitoring systems that capture and store vital tire data. Previously this information had only been accessible when the vehicle passed a fixed point in the mine, or when mine personnel manually downloaded the data. Integrating this technology with a mine management system enables remote collection and management of trend and alarm data. Mine personnel can now monitor a tire?s health parameters at any time, anywhere on site, regardless of the vehicle?s location. Anomalous tire conditions can be detected early and corrective actions taken. This information can then be integrated with other major onboard systems, operating conditions, and geographical information. Tire monitoring no longer exists as a stand-alone technology, but has evolved into an important integrated tool for mine operators. This paper will review the current status and benefits of integrating this emerging technology with a real-time mine management system.

May 1, 2002

By Michael P. Hardy

The report described improvements and applications of the Hybrid Computer facility. Improvements implemented under U.S.B.M. Contract H0252035 included expansion of the capability to model nonlinear seam behavior, installation of a color video output display monitor, and further development of software capabilities. To demonstrate the capability of the system, firstly, the influence of nonlinear seam behavior response to the occurrence of coal mine bumps was fully investigated and secondly, the effect of improper mining sequence on bump occurrence was demonstrated. In addition, the system was applied to the analysis of a series of practical coal mine problems. Mines in three coal seams were analysed to investigate the parameters which contribute to the occurrence of coal mine bumps.

Jan 1, 1977

By M. L. Bakker

The ISASMELT? top submerged lance (TSL) bath smelting process was developed in Mount Isa, Australia by Mount Isa Mines Limited (now a subsidiary of Xstrata plc) during the 1980s. By the end of 2011, the total installed capacity of the ISASMELT? technology will exceed 8 000 000 metric tons per year of feed materials in copper and lead smelters around the world. Commercial plants, operating in Belgium and Germany, are also batch converting copper materials in ISASMELT? furnaces. This TSL technology is equally effective for continuous converting processes, in which role it is called ISACONVERT?. This paper presents the recently patented ISACONVERT? process for the continuous converting of nickel and platinum group metal (PGM) containing mattes using the calcium ferrite slag system. The paper focuses on the potential application of the ISACONVERT? technology to existing nickel and PGM smelting complexes.

Jan 1, 2011

By Fathi Habashi

"On August 3, 1888, German Patent No. 43977 entitled ""A Process for the Production of Aluminum Hydroxide"" was issued*. The discovery which led to the patent was made by the Austrian chemist Karl Josef Bayer (1847-1904) (Fig. 1) who was at that time in Russia, and the process became known as the Bayer Process in his honour(1)(2)- The process imediately achieved industrial success, displacing the pyrometallurgical process that had been used until that time to produce alumina. The Bayer Process involved the pressure leaching of bauxite with NaOH solution to obtain sodium aluminate solution from which aluminum hydroxide was precipitated by seeding. Today bauxite is not only the principal source of aluminum but also of gallium, both metals being effectively recovered by the Bayer Process. The purpose of this paper is to outline the historical background of this discovery and its importance to hydrometallurgy."

Jan 1, 1999