Search Documents

By G. M. Molinda

Ground Penetrating Radar (GPR) is being investigated for the potential to determine roof hazards in underground mines. GPR surveys were conducted at four field sites with accompanying ground truth in order to determine the value of GPR for roof hazard detection. The resolution of the current system allows detection of gross roof fractures (>63 cm (s1/4 in) zone) or rider beds in coal measure roof. Data quality is not yet sufficient to detect small bed separations or subtle lithologic changes in the roof. Differences in data quality are discussed, as well as suggestions for collecting improved data.

Jan 1, 1996

By Moyle F. J

This paper describes an apparatus which was developed to study solid-vapour equilibria and presents results which were obtained during a study of the FeCI3-AlCI3-CI2 system. Analysis of the results showsthat fractional desublimation might offer a means of achieving a useful separation of the iron and aluminium chlorides produced by the chlorination of bauxite. The results, presented in the form of isothermal vapour pressure curves covering the range of temperature 160-200°C, support the earlier findings of Semenenko et al (Dokl Akad Nauk SSSR, 154: 42-43 (1964)) that the solid phase contains two terminal solid solutions.The equilibrium constant for the formation of the mixed dimer, FeAICI6, was approximately 4. The latent heat of sublimation of aluminium chloride varied from 18 to 26 kcal/mole AI2CI6 for solid compositionsfrom 0.9 to 0·5 mole fraction FeCls3.

Jan 1, 1979

By Kameron Ray, Ruilin Yang

This paper compares the modeling results obtained by using a single seed waveform (SS) versus multiple seed waveforms (MS) as inputs to the Multiple Seed Waveform (MSW) blast vibration model. The field data for the comparison was collected at a coal mine. The results of the comparison showed that the MSW model yields more accurate predictions and significantly higher correlation to field measurement when using MS as input. When using a single seed waveform as input, different seed waves result in different predictions of PPV. In contrast, using the multiple seed waveforms as an input, more consistent results are obtained.

Jan 1, 2013

By R. V. Ramani

"A computer simulation model of a dragline has beer developed for the study of alternative dragline deployment schemes for varying geological and mining conditions. In this paper, the mathematical aspects of the model, the input data and output results are discussed. An application of the model to a coal mine in eastern Kentucky is presented.IntroductionDraglines are very productive machines. To extend their operating ranges, they are operated in several modes such as advance benching, key cut, extended benching and pullback. Unfortunately, these variations result in low machine productivities. Appropriate methods to operate these machines must be developed on the basis of detailed analyses of dragline performance under varying geological and mining conditions. There are several standard engineering procedures for the selection of dragline, and design of a dragline pit (Ramani, Iroegbu and Manula, 1976). However, the complex interrelationship which exists among equipment, methods and natural conditions can be quantified only through orderly and systematic experiments.Computer simulation is well suited to studying these types of equipment selection and method layout problems. Several alternatives can be analyzed in a relatively short time by the modification of input variables. Also, the application of computer simulation models can significantly reduce the manpower and cost required for such analysis."

Jan 1, 1985

By H. Conrad

The strain hardening associated with the creep of magnesium single crystals at room temperatu.Je was investigated by shear tests in which the direction of stressing was reversed a number of times after creep in a <100> direction. The strain hardening was strongly anisotropic; the largest amount occurring in the direction of flow and the least 180 deg to this. The time law for creep changed from a parabolic type to logarithmic for the first and subsequent reversals of stress. For a given stress the creep strain decreased significantly for the first and second reversals and then only slightly for subsequent reversals. The logarithmic creep constant a changed in a similar manner. A linear relationship was observed between the creep strain for a given reversal and the stress. The slope for the third reversal yielded a strain hardening coefficient 12 to 16 times greater than that observed for unidirectional flow. Al-though no recovery was observed upon resting at room temperature, the hardening resulting from stress reversals could be completely removed by heating to 450" C. PREVIOUS work1.&apos; indicated that the creep rate of magnesium single crystals tested in the temperature range of 78" to 364°K decreased with time. This was attributed to an increase in internal stress resulting from an accumulation of dislocations at internal obstacles. The object of the present investigation was to further evaluate the nature of this hardening by conducting tests in which the direction of stressing is changed after previous creep in shear in a given slip direction. Previous to 1950 three investigations indicated that a Bauschinger effect3 occurred for single crystals as well as polycrystals brass in tension compression,

Jan 1, 1960

By H. Lawson

The Mine Safety and Health Administration (MSHA) issued Program Information Bulletin P09-03in April of 2008, providing formal guidance on using programs that model the redistribution of stress during underground mining of coal. A key part of this guidance is visual observation and mapping of ground conditions. If a correlation between ground conditions and model output can be established, the model is considered to be verified, and can be used to guide mine design in similar ground. A simple scale is recommended for ranking observed roof, rib, and floor conditions. This paper discusses optimization and implementation of a ground condition rating scheme in the gateroads of a deep underground longwall coal mine. Roughly 80% of each gateroad length deteriorated in a fairly uniform manner. However, this manner varied between gateroads, as did pillar size. The implementation of a ground condition mapping program, similar to that recommended in PIB 09-03, was successful in characterizing the ground response to mining in gateroads of a longwall coal mine.

Jan 1, 2012

By K. P. Stricker, H. Keddeinis, K. Grebe

Recent investigations by Mannesmann Research have shown that disintegration of sinter with widely varying quality levels is subject to a much more complex set of influences than was previously assumed. It was confirmed that disintegration at temperatures between 300° and 600°C (570° and 1,110°F) is triggered by the degradation of hematite. The specific tendency of hematite to disintegrate is, however, not constant: sinters containing the same amount of hematite can show widely differing disintegration tendencies, depending on structural homogeneity, porosity, and gangue quantity. Sinters with heterogeneous structures transmit stress to the hematite phase and this favors disintegration. Another factor is the brittleness of the glassy silicate phase, which can be influenced even by small modifications of minor gangue constituents.

Jan 2, 1984

By Lane White

The 1989 Annual Meeting and Exhibit of SME in Las Vegas, NV, February 27 - March 2, 1989, was the largest ever, drawing more than 4000 regis¬trants and 240 exhibit booths. Technical sessions included presentation of nearly 500 papers, including symposia on Biotechnology in Minerals and Metals Processing, Surplus Capacity in the International Metals Industry, and APCOM `89 - the 21st International Symposium on Application of Computers and Operations Research in the Mineral Industry. Technical sessions covered the gamut of minerals industry interests; however, the proximity of the meeting to recently surging gold development in Nevada drew special attention to gold operating practices. Several of the papers on gold processing are reviewed below. To keep pace with the strong world- wide interest in gold development, SME has scheduled three additional upcoming programs that will focus specifically on gold: World Gold &apos;89 - Gold Forum on Technology and Practices will be held November 5 - 8, 1989 in Reno, NV, as a joint meeting and exhibit between SME and the Australasian Institute of Mining and Metallurgy. Technical sessions will encompass a full program of papers covering geology and exploration, mining, and mineral and metallurgical processing. Cooperating sponsors for this meeting include the Canadian Mineral Processors Division of CIM, The Institute of Metals, The Institution of Mining and Metallurgy, The Mining, Geological & Metallurgical Institute of India, and The South African Institute of Mining and Metallurgy. Gold &apos;90 - Salt Lake City, UT, February 26 - March 1, 1990, will be a symposium held in conjunction with the 1990 SME Annual Meeting. Current research on the processing of refractory gold ores will generate innovative papers on process mineralogy at this symposium, with special emphasis on gold with pyrite and gold with carbon. Other sessions are planned for gold exploration and mining, gold metallurgy, gold plant design and practice, and gold in scams. Advances in Gold and Silver Processing Conference, October 1 - 3, 1990 will be held in Reno, NV. Preliminary planning calls for technical sessions on heap leaching practice, refractory ore processing, non-traditional lixiviants, bioleaching, metal recovery from solution, and the environmental aspects of processing operations. PLANT DESIGN, OPERATION Technical sessions organized by the Minerals and Metallurgical Processing Division of SME at this year&apos;s meeting in Las Vegas covered a wide range of gold operating practices. Eight papers relating to gold plant design, operation, and equipment are summarized here. Preprints of these papers are available by writing to Publications Sales, PO Box 625002, Littleton, CO 80162-5002 ($2.50 per paper for AIME members, $4 for nonmembers). Continuous elution process A. M. Stone, of Bechtel Australia Pty. Ltd., described the "Development of the Continuous Elution Process for Extraction of Gold from Carbon" (pre-print 89-75). Developed by Bechtel Pacific Corp. for Ok Tedi Mining Ltd., the Continuous Elution Process uses the same reagents as batch processes for elution of gold from carbon, while yielding significant savings in stripping vessel size and energy consumed in comparison with equivalent batch processes. The process is also simpler to operate than batch processes. Other advantages include reduced maintenance costs, higher average eluate grade, and near steady final eluate grade. Pilot testing for the Continuous Elution Process was conducted at Western Mining&apos;s Kambalda gold plant beginning in December 1982. The Continuous Elution Process is a continuous countercurrent system operating in a pressure vessel at elevated

Jan 1, 1989

By J. Oyunaa, P. Munkhbaatar, A. Sarnai

"The molybdenum mining process used at Mongolia Erdenet Company is a selective flotation of molybdenite from the copper porphyry ores in which the extraction of molybdenum comes as a byproduct of the ongoing copper production.The mineralogical composition of molybdenum concentrate is 99.4% molybdenite (MoS2), 0.09% molybdenum oxide (MoO3), 0.52% powellite (CaMoO4) and wulfenite (PbMoO4) and content 47.76– 47.92% molybdenum, 1.5–2.67% copper, 0.04% renium.From compared solvents sodium and carbonate and ammonia are like extracted molybdenum than hydrochloric acid, which contained 96.23–97.72 p.c. of its total amount. Hence to take into consideration abundance, cheap and suitable for analysis and processing the molybdenum concentrate ammonia is choosing as a basic solvent. By direct evaporation of ammonia extract solution, we obtained ammonium ortomolybdate, which contains 73.47% MoO3. INTRODUCTIONMolybdenum occurs in the earth’s crust in an abundance of about 10–14%, mainly as molybdenite, MoS2. Small quantities are also associated with other metals having similar chemical properties. Thus wulfenite (PbMoO4) is found in oxidized parts of sulfidic lead deposits in many regions of the world; powellite [Ca(Mo,W)O4] is a calcium molybdate usually formed from the modification of molybdenite in deposits containing tungsten as scheelite (CaWO4) and tungsten substitutes for molybdenum up to about 10%. Ferrimolybdite (Fe2Mo3O12·8H2O) is the product of oxidation of molybdenite in the presence of iron (III) compounds. Molybdenite is the primary source of molybdenum. Should demand for molybdenum rise so that additional sources become necessary, wulfenite, powellite, and ferrimolybdite may become commercially significant. Molybdenum ore is mined by underground and open-pit methods. A typical primary molybdenum ore body contains 0.05–0.25% Mo, and secondary ore bodies (copper porphyry ores) average 0.3–1.6% Cu and 0.01–0.05% Mo. Flotation remains the preferred and almost exclusive method of upgrading the molybdenite mineral to an industrial-grade molybdenite concentrate containing 90–95% MoS2, the balance being gangue (Habashi, 1997)."

Jan 1, 2016

It has been proven theoretically and experimentally that the use of 10 - 30 per cent DRI in blast furnace along with iron ore or sinter results in lower coke rate and higher productivity. However, to-date this remains unpractised on a regular basis mainly because of economic reasons. The DRI produced by several methods are expensive and difficult to store/handle in large quantities because of its reactive nature and thus DRI in blast furnace remains unacceptable.

Jan 1, 1999

By Greg Sheppard, Eduardo Nebot

Australian researchers have developed new technologies aimed at improving safety and productivity at openpit mines. A data acquisition and feedback system for electric rope shovels has been shown to substantially reduce cycle times and decrease excessive machine duty caused by stalls. This data acquisition system was developed by the Cooperative Research Center for Mining Technology and Equipment (CMTE). It has been tested on a P&H 4100A shovel at Coal & Allied’s Hunter Valley operations and a P&H 4100XPB at BHP Billiton Mitsubishi Alliance’s Goonyella Riverside Mine in Central Queensland. In addition, CMTE member P&H Mine Pro Services has used the technology to acquire field data from a P&H 4100XPBrope shovel at RAG’s Belle Ayr Mine in Wyoming’s Powder River Basin.

Jan 1, 2002

By Jerry Bennett

This report describes the results of a survey of current blast area guarding procedures at surface and underground metal/nonmetal mines. It features five case histories (two surface and three underground mines) of blast guarding methods considered to represent the best systems in use in the U.S. Mining Industry. Elements of an effective blast guarding system are presented along with recommendations for improvements in current blast guarding practices. Industrial and military surveillance and detection technology was reviewed to determine if parallel technology exists for immediate application to blasting site security. While it is concluded that immediate transfer of industrial security technology will be limited, a number of recommendations are advanced for new research to adapt some of that technology for application to the mining environment. Two research areas considered to offer the most potential for improved blast guarding are presented. They are, computerized personnel tracking and blast area intrusion detection using infrared, microwave or E-field type detection systems.

Jan 1, 1981

By D J. Brake

There has been a strong trend over the past decade in hard rock mines towards the use of very high powered auxiliary (or secondary) fans; in many mines, the installed power for the secondary ventilation system now exceeds that of the primary ventilation system. This also reflects the trend to use two-stage auxiliary fans pushing air into a single ‘trunk’ duct that in turn splits into multiple branches with multiple outlets feeding multiple workplaces. This often produces a poor result in terms of face flows due to the high resistance, high leakage and badly managed duct outlets, as well as high fan capital and operating (power) costs, which in turn also results in a higher cost for the underground power reticulation/distribution systems. This paper explores the reasons why this trend exists and what ventilation practitioners can do to utilise less expensive systems that simultaneously deliver better workplace conditions. It includes a case study.CITATION:Brake, D J, 2017. Auxiliary ventilation design – why and how mines waste so much power on inferior systems, in Proceedings Australian Mine Vent Conference 2017, pp 27–34 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By M. L. Leblanc, J. F. Burzynski, D. J. Mossman

A strong heterogeneity in the distribution of Sb+/-Au deposits exists within the North Atlantic Acadian-Hercynian domain. This is reflected in the regional disparity in Sb production among the various producing countries. This work focuses on the nature and distribution of Sb+/-Au occurrences in the Acadian-Hercynian domain. A summary listing of the general features of Sb-Au deposits found in this area is given

Dec 1, 1991

By Clarke E. Schuetze

This project had as its objective the experimental investigation of water capsule production utilizing the Southwest Research Institute&apos;s submerged nozzle encapsulation apparatus (U.S. Patent 3,389,194). Initial efforts on this project involved nozzle configuration and shell formulation optimization. The shell formulation developed on a prior program was modified during the course of the project to obtain the best balance of capsule breakage resistance and water retention. Subsequent effort centered on determining operating conditions which would produce the best quality capsules for each candidate shell formulation as determined by laboratory tests. Some preliminary work was done to increase the production capacity of the encapsulation equipment. The program was extended with major emphasis concerned with scale-up studies of capsule production capacity and the treatment of problems associated with grouting cartridge fabrication. During the course of the program, water-containing capsules were produced which have good long-term water retention, block resistance and adequate strength. Using a single-nozzle design, a production capacity of 15.9kg (35 pounds) per hour was demonstrated to give acceptable capsules based on initial results.

Jan 1, 1978

By Koehler Stout

Many hydraulic backfills are deposited at low density and provide less than optimum support strength to stope walls. This laboratory study shove that fill strength can be considerably increased. Placement methods used to increase the fill strength were the head, vibratory, cementation, double-planed (dblplod), and combinations of these methods. An experimental facility van designed to study the placement cathode and resultant strengths of the fills. Physical property tests made on the fills included laboratory penetration and vane shear plus several supplementary tests, such as grain size distribution and relative density. Test results were compared to fills planed by conventional methods and to those results reported by other investigators. When compared to fills placed by conventional methods, the penetration modulus was increased by 4.3 tines when the uncemented-vibrated-head concept was used and 71 times when the cemented-vibrated-head-dblplod concept was used. Apparently, hydraulically fill strength can be substantially increased. Conceptual mining plans are also included on suggested ways of placing and using high-modulus backfills.

Jan 1, 1979

By R. J. Kline

Most accidents are the result of risk taking. They can happen anywhere. Our coal industry categorizes accidents by type, occupation, commodity, age, every way you can imagine. We now know, how many were injured and when, for all the different types of accidents. We have ask ourselves many times, why are we having accidents, how can we stop the accidents and fatals in our industry? Present numbers and projections do not show that this will happen. Serious accidents can result in fatalities. Fatal accident can be prevented, and the coal industry can achieve zero fatalities. How soon this happens, depends on a great number of factors. I will discuss accidents and reasons for us having accidents in an attempt to get to the root causes. The historical perspective will be touched on, and the risk and analysis of accidents will be probed.

Jan 1, 2000

By Svato Prochazka

Content: ? commonly used drive systems ? drive system efficiency ? introduction to SR technology ? SR drive system advantages Commonly Used Feeder Drives Technologies ? VFD + induction motor ? hydraulic drive + hydraulic motor SR drive + SR motor

May 1, 2010

By D. J. Parker

In attempting to discuss a subject of this character it should be clearly understood at the outset that the purpose is not to emphasize the mere fact of occurrence of such catastrophes, the memory of which time has largely relegated to oblivion, but rather to stress the means of their prevention, available not only subsequent to but also at the time of occurrence. A careful, conscientious, unbiased study of the causes of mine explosions leads inevitably and definitely to the conclusion that the human element is the most important factor. The human factor should however, be evaluated in terms of responsibility--responsibility on the part of the employer to recognize the existing hazards and take the necessary remedial action, and on the part of the employee to perform his duties faithfully, diligently, scrupulously, and in strict conformity with State mining laws and company rules or other regulations.

Jan 1, 1933

Mr R. C. J. Goode (President) was in the Chair. There were also present one hundred and thirty-six Members, including Messrs R. J. Adamson, Dr J. M. Bereza, Messrs M. Barcza, H. Britten, H. E. Cross, J. K. E. Douglas, G. W. Holl, Dr J. P. Hugo, Messrs C. J. Irving, P. Lambooy, Prof J. de V. Lambrechts, Mr D. G. Maxwell, Dr J. T. McIntyre, Prof R. P. Plewman, Messrs J. F. Reid, V. C. Robinson, H. Simon and P. W. J. van Rensburg (Council Members), G. Abdinor, C. B. Anderson, H. F. Allan, E. L. Atkinson, V. C. Barnes, J. F. Bennet, W. W. Bath, R. E. Barnes, C. L. Berrange, J. P. Buds, Dr W. Bleloch, Dr L. A. Bushell, Messrs D. L. Carson, D. D. Cornier, R. S. Cooke, R. R. M. Cousens, J. P. Coetzee, W. L. Cousens, J. Daniel, R. Daniel, D. G. Davies, S. K. de Kok, V. S. Dillon, B. S. Dykhouse, Dr H. G. Denkhaus, Dr R. S. J. du Toit, Messrs J. I. L. Edwards, R. C. Espley-Jones, J. C. Ferguson, D. T. Fourie, A. Frost, W. R. Flook, Dr N. P. Finkelstein, Messrs D. F. H. Grave, J. M. Gosnell, E. K. Gibson, R. W. Grout, E. W. Gray, J. S. Hay, F. G. Hill, H. N. Hepker, J. P. Hoffman, C. G. Hodges, D. M. Jamieson, Dr D. G. Krige, Dr N. P. Lategan, Messrs J. E. Laschinger, J. Levin, C. P. Linsell, J. O. Kempe, F. Q. P. Leiding, A. I. Lee, D. G. Malan, W. Malan, H. W. McCulloch, R. D. R. Munro, C. S. Macphail, Dr T. F. Muller, Dr A. J. Nel, Messrs S. C. Newman, G. G. Nicolson, G. Y. Nisbet, J. A. Papenfus, E. Pavitt, W. H. Pittie, P. C. Pirow, P. G. D. Pretorius, N. F. Peverett, R. P. Plaskett, M. P. Pearse, W. Pilkington, T. K. Prentice, Dr R. E. Robinson, Messrs R. B. Richardson, R. St. J. Rowland, R. J. Rouillard, F. O. Read, W. T. Ruhmer, D. Savile Davis, E. F. Statham, K. Smith, H. Simon, G. B. Stern, C. D. Storrar, Dr N. B. Strydom, Messrs J. H. Talbot, A. H. Taute, J. H. Taylor, G. W. Thiel, K. A. Tweedie, W. E. Vance, Dr H. J. van Eck, Messrs L. W. P. v. d. Bosch, P. A. von Wielligh, N. B. Vinson, S. J. Venning, W. M. Walker, D. T. Watt, Dr H. J. R. Way, W. T. L. Wayman, R. G. Williams, L. G. S. Wright and C. F. Ziervogel. Thirty Associate Members, including Messrs E. Collier, G. Douglas, D. H. Gray, H. G. Gericke, R. Hemp, N. M. Hayne, A. Hazell, P. M. Johnston, D. E. Love, Miss V. E. Marting, Messrs R. G. Matthews, P. Malpage, D. Nicolle, R. Pendreigh, J. J. Rosslee, R. W. Shearer, R. F. Taylor, G. C. Thompson and D. A. Viljoen. Three graduates, Messrs G. S. Giles, J. P. Hatfield and J. A. Jones. Five Affiliates, Messrs A. C. Collie, E. Collier, A. B. Cook, W. Jacobs and G. M. Thain. Two Students, Messrs C. J. Bircher and R. P. Henrard.