Search Documents

By William L. Rice

This Bureau of Mines Open File Report on nickel is one of a series of minerals availability commodity deposit abstracts. Nonconfidential information from the Minerals Availability Program data base covering domestic and foreign nickel properties and deposits has been abstracted for use in this report. Abstracts include applicable data on location, published reserves and resources, geology, mine and beneficiation systems, and operation information.

Jan 1, 1984

By Enrique Touceda

FOR a number of years prior to the world war, the firm of Geo. H. Thacher & Co., of Albany, N. Y., was engaged in the manufacture of marine and other gray-iron castings. At -the outbreak of the war the firm decided to specialize in the manufacture f propeller wheels. It attacked the problem, therefore, from a foundry point of view, seeking to produce a casting that would be so accurate that no subsequent machining would be required on the blades, also from the point of view of the ship builder. There were two general methods f manufacture, the shortcomings of which have been freely acknowledged. In the sweep method, the nowel, or bottom half-mold, for each blade is swept up by a spindle beam and pitch race, while the top half-mold for each blade is built up individually. In the pattern method one individual blade, with the hub or hub portion, is mounted on a spindle and the individual -blade mold formed, the pattern is then rotated on the spindle to the position- for the next blade, etc. In rare cases wheels were made from a solid pattern. Owing to the cost of the pattern, its failure in many instances to be correctly made, and (when made of wood) its early and sure distortion the disadvantage of this practice is obvious, while metal patterns in most instances were prohibitive in cost. In these methods both green-sand and loam molding was practiced. The casting produced by either method can be considered only as a blank from which the propeller must be machined. The back surface f each blade must be chipped too the templet and through this procedure chipped to such accuracy, as will be required for a static balance. Inasmuch as the' work done by the machine tool is confined to the driving face of the blades, not only is perfection most difficult, but corrosion will be greater because of the removal of the dense skin f the casting and the local strains set up by the pneumatic tool in chipping. To produce a finished 9-ft. propeller for a Navy destroyer required from 8 to 21 days f foundry work and about the same length of, time for the machining. Through the use f the Thacher process, only as many hours are required, besides it is possible to produce a finished casting in perfect conformity, with any particular propeller-wheel design,

Jan 4, 1921

By Ralph Harris, Qi Xia

"Gold cyanidation rates are known to be limited by the rate of oxygen dissolution in the cyanidation tanks. The effect of solids loading on the oxygen dissolution rates is not obvious and the results of previous studies are ambiguous. The present paper presents an analysis of oxygen dissolution rates using a ""spent"" commercial gold slurry diluted to various levels of solids loading. It was found, in an 170 litre stirred tank reactor using an inverted cone sparger, that under certain high loading conditions, there was a decrease of as much as 50 %, i.e., there was a halving of the rate of oxygen dissolution as compared to that in clean water. In particular, it was observed that, due to gas flooding of the impeller, there was a drop in kLa even with an increase of gas velocity. Gas holdup reached a maximum value of only 1.7 %. The total power consumption was between 0.06- 0 .10 kw/m3 within the range of gas velocity before flooding occurred. The decrease in oxygen dissolution rate with increased solids loadings is believed to be mainly due to the increase in the apparent viscosity which reduced the turbulence and shearing effect and resulted in larger bubbles and hence reduced the reaction area a. The interrelations between solids loading, gas holdup, flow pattern, power consumption, and liquid mass transfer coefficient are discussed.IntroductionThe reactors generally used in gold cyanidation are Stirred Tank Reactors (STR). Compared with other types of reactors like fluidized bed reactor and column reactor, STR is of particular importance due to its wide application in industry. It is reported that the stirred tank reactor is used for more than 50 % of the world's chemical production (Xu and McGrath, 1996)."

Jan 1, 1997

By R. R. Faddick

Properties of coal-water slurries were studied in two separate phases: a rheological phase and a pipeline phase. The purpose of the study was to investigate the rheology of fine coal slurries to determine the effect of fine particles in a coal-water mixture on the economic and operational aspects of a slurry pipeline. The slurries consisted of 6x10, 100x200, and 200x0 mesh coal in water. A fourth slurry consisted of a mixture of the 6x10 and 200x0 mesh coal. Brookfield and Stormer rotational viscometers were used to obtain or simulate rheograms for a range of fine coal concentrations, temperatures, and particle sizes. All the slurries were pumped through a 1-inch diameter acrylic pipe. The fine coal slurries were found to encompass four distinct rheological models. The narrow size distribution of the coal slurries was apparently responsible for the high pipewall friction losses, more so than the particle size. A scale-up method applicable to Bingham plastics was found satisfactory for predicting pipeline headlosses of fine coal slurries from rheology data.

Jan 1, 1974

By M. W. Von Bernewitz

Corduroy is used for saving gold in small Land large milling plants throughout the world. Investigations by the Metallurgical Division of the Bureau of Mine indicate that corduroy blankets, used with or without a trap or jig in the mill classifier circuit, often are effective in concentrating gold and sulfides, especially if the gold does not amalgamate readily and if not enough sulfides are present to warrant the use of a shaking table, flotation cells, or cyanide plant. Most cold-mining countries include several or many small miner, that produce siliceous ores low in sulfides and gold, which can easily be amalgamated or caught in traps or jigs or on corduroy and shaking tables. At these mines the ore is crushed by stamps or bill mills, and the flow sheets include plates, flotation cells, and cyanide treatment, yet probably nearly as much of the pair minerals may be recovered by the less expensive plant. A well-known western maker of mine and mill equipment asserts, as the result of considerable observation of installed plants, that old and other valuable minerals should be caught as soon as they have been released by a mill, end recommends jigs to do this. A supplier of corduroy has informed us that at some mines this material is being replaced by jigs that catch gold as fine as 400-mesh. But for the small operator, inexpensive equipment such as a corduroy table may be better adapted and give a good recovery of gold and associated minerals.

Jan 1, 1939

By R. Ciccu, P. P. Manca, A. Bortolussi, G. Massacci

Tool performance and the unit cost of cutting depend on a number of operational variables (peripheral velocity, pull-back force, water injection rate, angles of the sections of wire outside the rock) as well as on the geometric features of the cut itself (area and shape). Cutting rate and wire productivity are also influenced by the type and number of diamond beads per unit length of wire and by the characteristics of the rock (granite or marble). A computer program aimed at handling a problem of this complexity has been developed and tested with the use of available field and laboratory data and has been found acceptably reliable. Discrepancies between current industrial data and some of the results suggest future lines of research, while the simulation should also be extended to include different types of rock and tool and a variety of bench face geometries

Aug 1, 1994

By James A. West

Near East region countries continued to supply a large share of the world's energy requirements in 1965. The area accounted for nearly 27 percent of estimated total world crude oil output and for about 60 percent of world exports of this commodity. Also, it was the source of more than 40 percent of the world's petroleum refinery products exports. Although other mineral industry activities remained relatively in? significant in comparison with petroleum, regional production and export of certain metallic and nonmetallic mineral commodities were of world significance. Of these commodities, chief in importance were chromium, copper, mercury, antimony, boron, potash, and phosphate Tack. The Near East region contains the largest and most productive oil resources in the world. Petroleum exploration and development operations during 1965 resulted in crude oil reserve additions of almost 8 billion barrels to increase proved reserves to 219 billion barrels at yearend, an amount equal to nearly 68.5 percent of the world's proved oil reserves. Near East countries' production of crude oil averaged a record 8.337,575 barrels per day in 1965, an increase of nearly 11 percent over that of 1964. On an annual basis, Kuwait continued as the leading oil producer in the Near East; however, Saudi Ayabia was a close second and its rate of production in late 1965 exceeded that of Kuwait. The major oil producing nations and their percentage of total area crude oil output was Kuwait, 26.0; Saudi Arabia 24.3; Iran, 22.3; and Iraq 15.9.

Jan 1, 1967

By Tuncel M. Yegulalp

The objective of this study was to categorize mining operations in the stone, and sand and gravel industries into areas of similar ground control functions and define initial factors affecting operational safety in each area, by means of utilizing publicly available data, telephone interviews and on site observations. The findings and recommendations presented in this report are based on the information collected during the two phases of the project. They also contain, in part, the collective qualitative opinion of the operators with respect to government rules and regulations on ground control safety and the implementation of these rules and regulations by government inspectors.

Jan 1, 1981

There is a significant amount of historical mining and exploration information available. This information is often distributed throughout a number of reports or plans, available from a variety of sources, and in many differing formats. The ability to capture paper-based historical information in a modem digital format provides mining and exploration companies with valuable information that can be used in a number of ways; for example, reassessments of exploration or mining work previously undertaken, or used in conjunction with current exploration information.   The purpose of this paper is threefold. Firstly, to present the paper-based historical information; highlighting some of the problems encountered, solutions to those problems, and any assumptions used. Secondly, to present the historical data in digital format, and demonstrate the tools available to analyse geological and associated information, and finally, to illustrate some of the potential future applications of the information, including mining optimisation, mine design and scheduling.   The Glenorchy scheelite/gold prospect has been used as an example. Within the overall prospect two smaller areas were selected. The Mount McIntosh and surrounding areas, focuses on exploration and surface excavation information. The Mount Judah area (State and Kelly-Taylor workings) focuses on underground mining and exploration information.  

Jan 1, 2001

By Glenn Adkins

This report characterizes pivoting joints in the structures of mining machinery and how the wear on the various components, i.e., pins, lugs, yokes and bushings, may affect the safety of mine personnel where these components are allowed to wear excessively before repair or replacement.

Jan 1, 1979

By A Paz, H Lehto, M +stholm, I Roitto

Nowadays, the demand for a finer grind in minerals processing has set new challenges within the industry, particularly for grinding technology. Apart from a finer grind, energy efficiency is also a key driver in optimising comminution technology.Stirred milling technology, already proven in many other industries, delivers a modern, sophisticated, flexible and energy efficient grinding solution for fine and ultra fine grinding in minerals processing. Fine grinding technology is utilised particularly in concentrate regrinding to complete the liberation of valuable minerals after the first stage of concentration. Maintaining the correct particle and particle size distribution of the regrind product is crucial for downstream process performance. Stirred milling technology offers the unique possibility for online control and optimisation of the regrind product particle size. This paper describes the basis of this online control possibility and discusses the implementation of stirred milling technology in minerals processing, particularly in regrinding applications. The paper will also outline management and control of fluctuations in feed rate tonnages as well as particle size fluctuations in concentrate regrinding.CITATION:Roitto, I, Lehto, H, Paz, A and +stholm, M, 2013. Stirred milling technology - A new concept in fine grinding, in Proceedings MetPlant 2013 , pp 190-201 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By Paul Headland

The Washington Suburban Sanitary Commission (WSSC) has recently completed design for the Bi-County Water Tunnel Project. The project will include a 10-foot diameter, 5.3-mile long hard rock tunnel located within the Piedmont Physiographic Province in Montgomery County, Maryland. The rock formations present along the alignment are comprised of igneous and metamorphic lithologies. This paper presents the steps taken to characterize the complex geology along the tunnel alignment into a single ?Engineering Unit? based upon the intact rock and rock mass properties. The Rock Mass Rating (RMR) system is planned to be used as the basis for dividing the ground into three ?Excavation and Support? classes. This RMR approach was selected to establish contractual baselines as presented in the Geotechnical Baseline Report (GBR) and is intended to facilitate management of the ground support characterization during construction.

Jan 1, 2008

By C. H. Bloomster

This study estimated (1) radon and radon daughter emissions from underground uranium mines; (2) the reduction in radon that would be released to the surface by using control techniques such as bulkheads, sealants, backfilling, and positive pressure ventilation; (3) the cost for radon and radon daughter removal from total exhaust air; and (4) total radon and radon daughter discharge for lower occupational exposure limits. For 13 large underground uranium mines, estimated yearly radon emissions from each mine ranged from 900 to 3,400 Ci. The estimated age of air emitted from the mines ranged from 11 to 37 min. Potential radon removal methods for the total mine exhaust were evaluated. The cost of these methods was prohibitive. Diurnal and seasonal changes may affect radon emission over short periods of time, but do not affect the total emissions over the long run. Radon and radon daughter emissions would be little changed by increased ventilation requirements needed to achieve lower occupational exposure limits. The concentrations in the exhaust would be lower, but the total release would be the same

Jan 1, 1984

By R. Benito

This paper describes the application of modern data-analysis tools, such as data mining, to determine a representative cost driver for haulage activity. This cost driver was subsequently used to trace incurred haul costs by bench for openpit optimization. For this purpose, large amount of previously unused cost and production data from an open pit mine was extracted, loaded, transformed and integrated into a data warehouse. Predictive modeling was performed using Microsoft Decision Trees algorithm to compute expected unit haul costs by bench for future mine expansions. Finally, a sensitivity analysis was carried out to determine the effect of two cost drivers (if any) for incremental haul costs in the final pit outline process.

Jan 1, 2008

By F R. M Pires, R M. Carvalho

Supergene processes in banded iron formation (BIF) result in important dissolution, material transport and simultaneous disorder of the residual bands. The rock physical properties such as density, porosity and rheology change during the weathering attack. The itabirite, Paleoproterozoic metamorphic BIF from Quadrilßtero Ferrffero (QF) û Brazil, shows several weathered facies. Strong linking between topographic surface, rock density and iron grade occurs within the weathered zones. This linking is due to partial dissolution of silica and carbonate from itabirite and gravitational rotation and break of the remaining blades, generating kink-like slump structures. The original itabirite density, 3.7 t/m3, decrease at the first leaching steps, until 2.7 t/m3, and increase at the end of the leaching process until 3.6 t/m3. Iron grade increases from 38 per cent to 68 per cent and depressions (sinkhole), subsequently filled by Cenozoic basinal sediments, are developed over the enrichment zones. The formation of important supergene iron ore deposits of QF is intimately related to such a process. Several iron deposits at QF, such as Pico do Itabirito, Fßbrica Nova, Casa de Pedra, Tamanduß, -gua Claras, Cappo Xavier, etc., reveal the aspects related to the proposed evolution, implying that the formational process of the soft iron ores had a regional character. Granular medium model helped in the understanding of the development of the structure and the formation of the deposits. A numerical model has been developed in order to simulate a leaching system in a two-dimensional matrix, composed of two types of materials: leachable and unleachable. Equal volume proportion and vertical banding were considered. Drilling data was used as multipoint attractors to remove leachable matrix nodes.

Jan 1, 2002

By C. W. Davis

This is the first of a series of papers being; prepared as the work progresses in a study of the hydrometallurgy of manganese. The investigation is being made in an endeavor to make possible the utilization of lour-grade domestic manganese ores. The value of a hydrometallurgical process for manganese depends on the present and future uses for manganese products.

Jan 1, 1930

By M. U. Khan

"Underground mine diesel equipment generally offers more flexibility as compared to electric powered systems. Diesel exhaust is an adverse agent which affects the health of underground miners. The National Institute of Occupational Safety and Health (NIOSH) regard diesel exhaust as carcinogenic. The NIOSH 5040 method is an established technique for measuring Diesel Particulate Matter (DPM). This process inherently involve a lag time before an accurate exposure determination can be made during which miners are potentially overexposed to DPM. This issue can be addressed by using realtime DPM monitors. This paper presents underground mine shift average based and realtime monitored DPM values monitored in US mines. A FLIR Airtec instrument has been used for realtime measurement whereas shift average based DPM has been determined by the use of NIOSH 5040 method. A log of diesel equipment movement was kept. DPM concentrations versus time were plotted and analyzed. High DPM sources were identified and the FLIR Airtec was demonstrated to be satisfactory for realtime DPM measurements. INTRODUCTION The use of diesel equipment in mines is an attractive option due to its ability to convert a large fraction of available energy into useable work. Diesel engines are rugged, dependable and fuel efficient. It is very common for diesel engines in heavy duty trucks to have a life of 1,600,000 km [Anon, 1999]. Generally in underground mines compared to electric powered equipment, diesel equipment provides more maneuverability. It can be assumed that the underground mining industry will maintain its reliance on diesel powered equipment keeping in mind the recent developments in other energy alternatives [Anon, 2001a]. A harmful aspect to the use of diesel as a fuel is its resultant emission as an adverse environmental exposure agent. Generally diesel particles are approximately one order of magnitude smaller than respirable dust aerosols in underground mines (typically less than one micron in size) [Kittelson, 1998]. Force of gravity has less effect on DPM due to its small particle size. The phenomenon of less gravitational attraction increases the settling and residence time of DPM in the mine atmosphere. High residence time of DPM as compared to other mechanically generated particles increases the chances of diesel particles deposition in the human respiratory tract. The small sized diesel aerosols penetrate deeply into regions of the human lung [Morawska. et al. 2005], which increase the health risks associated with long term exposure to diesel aerosols. Published studies documented the adverse health effects of DPM exposure [Walsh M.P., 1999]. Continuous and long term DPM exposure can result in respiratory disease, lung cancer, reduced lung capacity, and heart disease. NIOSH has declared that the reductions in DPM exposure would reduce cancer risks. In underground mines DPM determination is a challenging task and it is becoming a matter of serious concern due to the harmful health effects associated with the exposure of DPM. The current study involves the determination of realtime and shift averaged based DPM in underground mines of United States of America (USA). Realtime DPM was measured using FLIR Airtec monitors and shift averaged based measurement was performed by the MSHA approved NIOSH 5040 method. FLIR Airtec uses laser scattering approach to measures the Elemental Carbon (EC) component of the DPM. The results from the FLIR Airtec were compared with the results of NIOSH 5040 method and its performance was found satisfactory."

Jan 1, 2015

By Ramin Motamed, Joseph A. W. Toth

Evaluation of the capacity of large-diameter drilled shafts using current load test methods present challenges when considering the magnitude of loads required to fully mobilize their capacities. Often, these full scale tests do not fully mobilize the capacity through side resistance. Therefore, the need for innovative solutions to extrapolate side resistance and interpret nominal capacity are of key interest. In this study, we evaluate three methodologies for extrapolating unit side resistance based on bi-directional load test data. Fellenius (2001) presented these methods for interpretation of pile capacity using static load tests. Our interpretations are based on the evaluation of 116 load tests. Unit side resistance was calculated and reviewed for each load test and categorized using three criteria of mobilization; (A) full, (B) partial and (C) linear. This study specifically focuses on load tests that showed fully mobilized unit side resistance behavior (Criteria A). The three methodologies were applied assuming Criteria (A) load tests were mobilized to 50% of their measured values. Subsequent comparisons of each extrapolation were then compared against the full measured values for each test and generally showed good agreement. INTRODUCTION It is widely accepted that conducting load tests such as standard top-down tests or bi-directional (i.e. O- cell) tests can help designers understand load-settlement behavior and the nominal resistance of drilled shaft foundations. These load testing methods provide the advantage of confirming design assumptions as well as improving the reliability of the foundation design. The potential cost savings from the application of these methods for mid to large size projects is self-evident. For example, in a recent project in Northern Nevada, an O-cell test on a 6.9 ft diameter, 114.8 ft length drilled shaft imposed an initial cost of $125k to the project, resulting in a 15% reduction on the total foundation cost; equivalent to $1.3 million in overall savings (Pease, 2014). However, the costs of implementing such methods on smaller projects can be prohibitively expensive (Hagerty et al, 2016). Despite the clear advantages of drilled shaft load testing, the current practice is not without limitations. Performing load tests on large-diameter drilled shafts with high capacities is a challenge considering the significant loads required to fully mobilize the capacity of such foundations. In some cases, the feasibility of these tests is impractical because the associated initial cost is not guaranteed to outweigh the final savings. As a result, large scale load tests are sometimes ruled out from the design phase of projects. Furthermore, in the majority of load tests the magnitude of loads applied are specifically selected to not approach failure, so the shafts can be used in the future foundation system (i.e. production shafts). This practice of field testing restricts our knowledge of the true capacity of the drilled shaft at failure; hence the nominal resistance remains unknown.

Jan 1, 2018

By John F. Gamble

Paper 1?South African experience with asbestos-related environmental mesothelioma: Is fiber type important? Neil White, Gill Nelson, Jill Murray The purpose of this review was to illustrate the importance of the type of asbestos in environmental mesothelioma. South Africa is a logical place to assess fiber type. The three major types of asbestos (crocidolite, amosite and chrysotile) were mined (all asbestos mining stopped in 2002) in South Africa. The association between asbestos and mesothelioma was discovered in South Africa. The occupational literature indicates high mesotheliomagenic potential for crocidolite, less for amosite and less still for chrysotile. Since South Africa has been a major source of crocidolite, relatively high rates of mesothelioma in the mining population is not surprising. High rates of mesothelioma due to environmental exposure is surprising, except perhaps when the authors? point out potential sources for community exposures (e.g., mine tailings used for road surfacing, golf courses, brick and plaster making; insulation in residential ceilings; children playing on fiber-rich waste rock). The authors? reviewed four studies reporting on mesothelioma cases and their sources of exposure and fiber type. Overall 23% of the known cases were attributed to the environmental (not occupational) exposure and about 90% were due to crocidolite asbestos. The proportion of environmental mesothelioma is considerably higher than in Western Australia where crocidolite is also mined. There the overall rate of environmental mesothelioma is about 6% (and less than 1% from residence in a crocidolite mining area).

Jan 1, 2007

By Alain Simard, André Gobeil, Sylvain Lacroix, Maurice Rive, Denis Racicot, Pierre Verpaelst

"The Abitibi volcano-plutonic belt forms the major portion of the Abitibi lithotectonic subprovince in the Superior Province. The Abitibi belt is composed essentially of"" (1) approximately 2.7 Ga old volcanic and sedimentary rocks; and (2) gabbro, tonalite, granodiorite and syenite intrusions occurring in well-defined prekinematic ( synvolcanic ), synkinematic and post-kinematic plutonic suites. Most of these rocks are metamorphosed to greenschist facies. Regional multi-phase deformation affects the volcano-sedimentary rocks. Deformation was initiated as these rocks were formed, and peaked at the end of the Keno ran orogeny with the emplacement of granitic batholiths.There are 145 former and current mines in the Quebec segment of the belt. To date, more than 420 Mt of ore have been extracted yielding 1,600 tonnesof Au, more than4,000 tonnesof Ag,4,400,000 tonnes of Cu and 5,300,000 tonnes of Zn. Mineral production is concentrated in geologic domains that approximately coincide with the boundaries of lithotectonic domains. We have compared the geology and mineral deposits of different domains to illustrate their distinct metallogenic signature. Certain domains are dominantly gold-producing (Cadillac-Malartic, Val-d'Or, Caopatina), others are base-metal producers (Matagami and Normetal), while others produce both gold and base metals ( Rouyn-Noranda, Chibougamau, Casa-Berardi-Joutel).Gold is extracted from quartz-rich vein deposits (for example, Val-d' Or), sulfide-rich veindeposits(Cadillac or Chibougamau) and from volcanogenic massive sulfide deposits ( Rouyn-Noranda). Base metals are generally mined from volcanogenic massive sulfide( RouynNoranda, Matagami, Normetal), although certain vein deposits yield base metals (Chibougamau) . Certain sectors are dominantly zincrich (Matagami, Normetal)."

Jan 1, 1990