Search Documents

By Frank R. Field, Randolph E. Kirchain, Elisa Alonso

"There are a number of environmental incentives for increasing recycling, including the reduction of waste, energy and resource use. Recycling can also be advantageous for manufacturing firms in both the short and long term. Secondary material can substitute for primary material, potentially dampening primary material price increases and reducing the pressure for greater primary extraction. This paper examines the potential for and dynamics of recycling for the case of platinum using a dynamic, behavioral simulation model of the primary and secondary markets. Since the secondary supply of platinum depends on a supply chain separate from primary extraction, recycling can diversify the risks of primary supply instabilities. Over time, recycling can cut primary consumption, reduce overall costs to firms, and possibly reduce the impact of price fluctuations upon firms.IntroductionThe benefits of recycling, from the perspective of the environment, are many, and the environmental benefits of increased recycling are considered a step towards increased sustainability [1, 2]. Life cycle assessments indicate that obtaining materials from secondary sources generally requires less energy and has fewer environmental impacts than extraction and refining of primary materials [3]. Analyses of materials flows show that, in addition to landfill volume reduction, recycling reduces primary material consumption, affecting long term materials scarcity [4, 5].The benefits of recycling are not limited to the environmental. Firms can benefit from the lower energy costs of recycling, especially that of metals whose primary extraction and refining are particularly energy-intensive (e.g., aluminum). The routine participation by firms in secondary materials markets (e.g., www.recycle.net) shows that this advantage has not gone unnoticed.Recycling can also benefit firms whose costs can be significantly affected by changes in material prices resulting from material shortages and material scarcity, with potentially permanent effects upon firms [6-8]. This paper focuses on the impact of recycling in the face of platinum scarcity for supply chain downstream firms."

Jan 1, 2008

By Elsa Olivetti

Life cycle assessment (LCA) is used increasingly as a tool to provide quantitative metrics of environmental impact and inform early stage materials selection decisions. One common challenge in LCA stems from allocation of burden when multiple adjacent products share some of the same processes. A critical example of this is the partitioning of benefit or burden at product disposition in open-loop recycling scenarios. This work reviews the challenge of allocation and investigates the various methods proposed for allocating end-of-life (EOL) burden. Specifically this work examines whether these methods lead to different results and explores the trends in allocation method bias for or against particular materials classes.

Jan 1, 2010

By Igor Zh. Bunin

A model for developing electric discharges between sulfide mineral (pyrite) particles under high-voltage nanosecond pulses in a liquid medium (water) is considered. A possibility of electrical breakdowns of liquid gaps between particles under nanosecond pulses is shown. This probability and the energy released in discharge channels depend strongly on the sulfide conductivity.

Jan 1, 2010

By Tiezheng Li

Keywords: Laminate Composites; Mechanical Behavior; Damage Evolution The mechanical performance of Ti-6-4-Al3Ti metal-intermetallic laminate (MIL) composites synthesized by a reactive foil sintering technique was evaluated. Crack morphology of untested Ti-6-4-Al3Ti MIL composites has been characterized by optical microscopy. Mechanical tests were performed on Ti-Al3Ti metal-intermetallic laminate (MIL) composites and pure Al3Ti, and the principal mechanisms of damage initiation and accumulation were identified experimentally. The elastic properties and anisotropy of the laminates were calculated and successfully compared with Resonant Ultrasonic Spectroscopy (RUS) measurements. The effect of residual stress on the fracture toughness of the Ti-6-4-Al3Ti MIL composites was analyzed.

Jan 1, 2005

By Changqing Su

A batch incubation experiment has been carried out to investigate the optimal condition for the microbial remediation of hexavalent chromium (Cr(VI)) in soils contaminated by chromate ore processing residue at Hunan Iron-Alloy Factory in China. The optimal condition was obtained by comparing the remediation efficiency of Cr (VI) by indigenous bacteria under different culture media, the quantity of nutrient sources, the pH and the temperature. The results indicated that glucose and yeast extract was the optimal component of culture medium and the quantities of the above components were 8 g L-1 and 13 g L-1, respectively. The optimal temperature and pH value were 30_ and 10.0, respectively. A bioreactor was operated under the optimal condition to evaluate the efficiency of Cr(VI) remediation in the contaminated soil. The result showed that water soluble Cr(VI) in soils was reduced from 320 mg kg-1 Cr(VI) of the initial concentration to below detection limit after 30 h in a bioreactor. Thus, there is a large potential to make bioremediation for the reduction of Cr(VI) to Cr(III) by the addition of optimal culture medium under aerobic condition.

Jan 1, 2010

By Magnus Ek

After the installation of three new converters as part of the recent expansion of the Rönnskär smelter completed in 2000 work continues to further improve the converter operation. The converter upgrade led to an increase in blister copper taps from 150 tons per batch to more than 300 tons. The total cathode copper production increased from 130,000 tons in 1999 to 230,000 tons in 2001, the first year in full production. In recent years focus has been to improve operating practise, maximize the blowing time, extend the converter campaigns hence to reduce the specific brick consumption and improve the converter slag composition.

Jan 1, 2005

By David Norval

Ni, Co, Cu and Pt, mattes are common materials that require granulating and milling of the resultant granules for further processing. This route is acceptable if the material is brittle (friable) which is a property associated with the higher sulphur mattes. For lower sulphur levels, where the matte is less amenable to milling, the costs of the milling increases. This paper will compare water granulation with certain dry granulation processes and the downstream processes required for Hydrometallurgy. It will further introduce and expand on atomisation which offers a further safety benefit in the control of the metal flow into the 'wet zone' with the use of a tundish flow control also reducing the conversion from the matte to powder in one fairly straightforward operation.

Jan 1, 2006

The effect of rare earth element Y (0-2.0at.%) on the microstructure of TiAl alloys at the as cast and rapidly solidified conditions has been investigated. The results show that the addition of Y greatly refined the microstructure of TiAl alloys at both conditions. The refinement is more significantly with higher Y content. The refinement of Y in the cast alloys is attributed to that the strip-shaped Y-rich phase locating on the grain boundaries impedes the grain growth during solidification. In the rapidly solidified alloys, Y-rich phase dispersing uniformly as spherical particles in the matrix acts as heterogeneous nucleation sites which increases the nucleation rate of ??phase during the ????phase transformation, and produces a refined initial microstructure during solidification. Higher cooling rate restricts the grain growth during subsequent cooling.

Jan 1, 2010