Search Documents

By Jim Belous

Fluid Dynamic Modeling (FDM) was used to develop solutions how to eliminate the fugitive emissions from the meltshop building and to comply with the EPA “6% opacity from the furnace operations” rule. Secondary Emission Control (SEC) system performance was simulated by an inverted 1:96 scale Plexiglas model of the entire meltshop, utilizing the negative buoyancy effects of saline solution in water. Test results show that with the installation of the internal partition wall which separates furnace aisle from the caster aisle, significant improvement of the SEC system is achievable, thereby avoiding large expenditure for the expanding a fume collection system capacity.

Aug 17, 2017

By Mário César Mantovani

The steel for gas turbine compressor discs (26NiCrMoV14.5) requires some mechanical properties like strength, impact, toughness, fatigue, and creep resistance in order to be used in such application. To achieve the properties required for the gas turbine compressor discs, the material should have very low contents of sulfur, phosphorus, antimony, tin and arsenic. The level of cleanliness should also be very high and this is possible by achieving low oxygen content keeping the deoxidation elements like silicon, manganese and even the aluminum in very low percentages. The main problem in refining such steel is to adjust a sufficiently low oxygen content to have a good desulfurization and at same time a good cleanliness without using silicon, manganese or aluminum as deoxidizers. Combination of initial selection material, steelmaking process control, forging sequence and heat treatment cycles can provide uniform mechanical properties throughout the gas turbine compressor discs. Villares Metals SA as a big player on special steels with complex process has been developing this kind of material for several years. The objective of this work is to show the process technology evolution involved in the production of this kind of steel under the discussed preconditions.

Aug 17, 2017

By Armando Vazquez

When water enters the EAF, some chemically dissociates to H2 while some remains as H2O vapor. Depending on operating conditions the levels of combustible gases (CO and H2) and H2O are continually changing throughout the course of any individual heat and on a heat-toheat basis. The EFSOP® system has been implemented in more than 80 installations as a powerful tool to reduce furnace operation costs but with water detection technology the off gas technology is a valuable solution to improve safety. This paper describes the latest results when using Tenova Goodfellow’s new standalone water detection technology that for the first time provides real-time analysis of both H2O vapor and H2 from start-to-end of a heat. It involves a newly designed water cooled probe and heated line that eliminates condensation during off-gas sampling and an analyzer equipped with a proprietary system for analyzing both H2O vapor and H2.

Jul 30, 2018

By Christoph Aichinger

The optimization and improvement of a modern integral iron and steel works gets more and more difficult as each individual plant is already operated at its best efficiency and at the lowest operational expenditures. However very often the individual plants are considered as stand-alone units and there are losses and inconsistencies on interfaces and take over points, which could be avoided and by that improving the overall performance of the iron and steel works as a holistic unit. Primetals Technologies looked into this subject extensively in the recent years and is now ready to offer new tools and services in order to assist operators to find further potential for improvement in processes, which seem to be fully developed at first sight.

Aug 17, 2017

By Mühlböck Marlene

Increasingly stringent global environmental regulations are forcing steel producers to continually improve the efficiency of sinter waste gas treatment. With the Selective Waste Gas Recirculation (SWGR) system from Primetals Technologies, lower production costs can be achieved and the size of downstream waste gas cleaning units can be reduced for investment savings. SWGR features the extraction and reuse of hot sinter off gas from selected wind boxes along the sinter strand, which contributes to improved energy efficiency and off gas treatment in the sintering process. With the next generation of SWGR, Primetals Technologies can provide an energy optimized, emission optimized and environmentally friendly solution that meet customer requirements and country specific regulations. This paper demonstrates the latest developments in selective waste gas recirculation, especially results from pot grate tests and comparison from lab to real plant data. Furthermore theoretical finding and mathematical modelling is presented.

Aug 16, 2017

By Levi de Oliveira Bueno

Constant stress testing was used for characterization of creep behavior of a 1Cr0.5Mo steel plate in the virgin condition. The tests were performed on creep machines equipped with Andrade-Chalmers type profiles, high sensitivity SLVC transducer extensometry, high stability temperature controllers, and facilities for monitoring the creep curves with an automatic data logging system. Ten creep machines of this type were used in this research, in an experimental work that lasted for one year. Three temperature levels were selected: 538, 565 and 593°C, with stress in the range from 69 to 258 MPa producing rupture times varying from 8 to about 4908 h. The creep curves were all followed with great scrutiny using data logger scanning rates which enabled storing thousands of readings in each case. The experimental analysis involved measurements of minimum creep rate, rupture time and final elongation at rupture. The data were analyzed according to the classical phenomenological / physical relations (Norton, Arrhenius, Zenner-Hollomon, Monkman-Grant) and also considering five traditional parameterization methodologies (Larson-Miller, Orr-Sherby-Dorn, Goldhoff-Sherby, Manson- Haferd and Manson-Succop). Comparisons are presented among the possibilities of data extrapolation from five different methodologies. Comparison is also made with creep results mentioned in literature for the same material in the virgin condition.

Aug 16, 2017

By D. F. Rodríguez-Pérez, J. Salinas-Reyes, Luis R. Salazar-Garza, C. A. Gómez-De-La-Garza

The Pickling Line Tandem Cold Mill (PLTCM) from Ternium Pesquería started in 2013. It is a line with 5 stands, 6 high; focused mainly on the exposed automotive market, with a wide spread of products with high quality requirements. In addition the operational continuity is very important, for this, one of the greatest challenges is to ensure operational discipline, the order of production, the quality of the input (hot band), operational interruptions, equipment failure, breakage of strip in the mill, among others. In relation to this, it has a strong impact on productivity, customer compliance, damage to equipment, rolls, safety, quality, reprocessing among others. Here is present the results obtained in the project "decrease of strip breaks" which focused on several fronts, discipline in the order of production, previous review of raw material in surface and dimensional defects with automatic inspection equipment in the hot mill, as well as in PLTCM, generation of logic in the redundant systems of alerts and prevention to avoid or minimize strip breaks that were high impact in the past. All these multidisciplinary actions led as a whole to a significant improvement in the performance indicators of the PLTCM, in productivity, compliance, reprocessing and quality in the cold rolled mill.

Oct 1, 2019

By Tiago de Abreu Siqueira

CO2 geological storage is one of the current technologies developed worldwide to reduce industrial emissions of carbon dioxide to the atmosphere. Two main mineral types of deep geological reservoir could be contemplated for CO2 storage: sandstone reservoirs and carbonaceous reservoirs. Geochemical reactivity of a dolomite-calcite mineral compound and magnesite pure mineral was studied with a set of nine experiments per crushed mineral phase with two saline solution and with mQ water and three temperatures: 50°C, 90°C and 150°C. Experiments were performed in batch reactors with 250 bar of CO2 partial pressure during 24h to assess the effect of temperature and salinity in constant CO2 pressure. Solid characterization was performed by XRD and solution analysis by ICP-OES. Acidification of solutions due to CO2 dissolution in water is the main source of reactivity in the system. Proton concentration increases and causes partial dissolution of initial dolomite, calcite and magnesite and release of Ca2+ and Mg2+ cations in solution. Bicarbonate anion (HCO3) concentration also increases due to CO2 dissolution in water and carbonate minerals dissolution. Temperatures of 90°C and 150ºC increase the kinetic of reaction and the dissolution of minerals and cations release in solution. New carbonate crystalline phase precipitates as a Ca, Mg solid solution between dolomite and calcite pure poles.

Aug 8, 2018

By Kengo Usui

The energy consumption of Iron-making, especially Blast Furnace (BF), is very large. In order to maximize the utilization of limited resource, it is essential to reduce energy consumption and recovering waste energy in BF. This paper introduces energy saving equipment based on NSENGI’s over 80 BF construction experiences since 1963. The first is the technology for the Top Charging System for low fuel-rate operation. One of the important factors to achieve such operation, the burden should be charged uniformly. Since 1974, NSENGI have developed and delivered over 80 Top Charging equipments for such purpose and nowadays, developed new type Top Charging equipment with improvement of charging precision. The second is the technology for Solely BFG Operation in Hot Stove, which means no use of other fuel gas such as LDG, COG. It is realized by high combustibility of NSENGI’s Top-Combustion Hot Stove with Metallic Burners, and large amount of heat recovery of Waste gas Heat Recovery system with heat medium. The third is the technology for effective energy recovery in TRT. With NSENGI’s latest Gas Cleaning System “Multi-Vessel Electrostatic Precipitator" (MVEP), TRT will be able to generate higher electrical energy by approx. 30% than that of wet-type. In comparison with dry bag-type, MVEP allows temperature fluctuation which lead to generate higher electrical energy by approx. 10% NSENGI therefore, will be able to accept and meet your request widely.

Aug 1, 2018

By Dustin Vickress

The premature failure of copper staves in the lower stack and bosh is frequently the cause for an interim blast furnace repair at great cost to the blast furnace owner. Protective accretions may form on the stave hot face, but when these accretions are lost the staves can begin to deteriorate both due to abrasive wear from exposure to the descending burden materials and due to thermal cracking from exposure to hightemperature process excursions. These mechanisms can lead to failure of cooling passages, which forces blast furnace operators to shut off these channels, accelerating the rate of copper stave wear. Finger cooler technology was developed to extend blast furnace life by restoring cooling to damaged staves. Evidence for their effectiveness is presented herein in the form of experimental test work and conjugate heat transfer (CHT) analysis carried out using computational fluid dynamics (CFD) simulations. These tests demonstrate that under typical blast furnace excursion conditions, a stave fitted with finger coolers will undergo half the temperature rise of a stave fitted with conventional cigar coolers.

Aug 17, 2017

By Fabiano Soares

Strand guide rolls in continuous casters are crucial components for guaranteeing an optimum process for the production of high-quality steel grades. The properties of these rolls greatly influence the quality of the slab produced. The most commonly used designs so far have been the axle roll and the solid roll. A quite new roll concept is the STEC-Roll®. It combines the advantages of the axle roll with those of the solid roll. This paper explains the development of this roll type and shows the current design. The characteristics of the STEC-Roll® are presented in greater detail and are underlined by a number of simulation results. Beside the design itself, the benefits for casting and maintenance are explained, including for example the easy assembly and dismantling or the use of the roll for dry casting. A brief examination is made of the TCO for the STEC-Roll® and an estimation is provided of the exchangeability of this roll. To conclude, an overview on the current applications is presented.

Aug 17, 2017

By Nicolás Ariel Zabala

During the make-up and break-out of the connections, threaded joints are exposed to intense mechanical and tribological solicitations. The connection performance is influenced by its geometry, material properties, surface treatments and thread compound. The aim of this work is to evaluate and characterize the tribological behavior of different thread compounds applied on manganese phosphated carbon steel under low speed and high pressure sliding contact. Four thread compounds were evaluated: one containing lead, zinc and graphite; other lead-free, containing copper and finally, the last two lead-free and containing non-metallic solids. The tribological behavior was analyzed by a block-on-ring tribotest. During the test, load varied linearly between 250 N and 7000 N; loading and unloading lasted 14 sec and were performed in opposite directions of rotation to simulate the make-up and break-out operations. Friction force and load as a function of time were registered. Upon completion of the test, wear surfaces were analyzed by SEM, optical microscopy and energy dispersive spectroscopy. The obtained results show that the lead and zinc containing thread compound displayed the best behavior, showing a wear reduction of approximately 20%. These results are in line with previously known oilfield experience. Average COF values around 0.15 were measured and no significant differences between dopes were observed; indicating that the wear behavior was influenced by the additive package.

Jul 31, 2018

By Ana Carolina Fernandes Reis

O objetivo do trabalho foi investigar a recuperação metalúrgica da flotação de sulfeto de ouro utilizando diferentes tamanhos de partículas, a partir de ensaios de moagem e flotação em bancada, visando analisar o melhor desempenho e seletividade do processo. O minério em estudo apresenta um teor médio de ouro de 5,28 ppm e 0,59% de S. Nos testes verificou-se uma correlação diretamente proporcional entre a recuperação mássica e metalúrgica, ambas mostraram-se inversamente proporcional a seletividade no concentrado. A granulometria com 90% passante na malha de 0,053mm obteve o melhor resultado de recuperação tanto do ouro como de sulfetos, em contra partida, apresentou o menor grau de seletividade.

Aug 16, 2017

By Claudio Marcio de Araujo

O trabalho apresenta o estudo e resultados da aplicação do dessulfurante micronizado Puresteel-1000, seus benefícios, economia e melhoria do processo de dessulfuração. Objetivando redução de custo e manutenção nos parâmetros operacionais a CSN desenvolveu junto a um fornecedor um dessulfurante a base de CaO que favoreceu o atendimento com redução de custo .A metodologia utilizada para o trabalho foi à avaliação do sistema produtivo da EDG-CSN, e o estudo de solução para o processo apoiado na revisão bibliográfica do tema. A implantação da aplicação do dessulfurante micronizado Puresteel-1000 obteve para a CSN ganho através da redução de custo de aproximadamente 30% no custo do dessulfurante, mantendo os mesmos parâmetros operacionais.

Jul 29, 2018

By André Emanoel Poroca Lins

O objetivo principal desse trabalho é produzir compósitos de matriz de alumínio AA1100, reforçado com um material cerâmico, o óxido de zinco (ZnO), utilizando o processo de metalurgia do pó e técnica de moagem de alta energia, compactação uniaxial a frio e sinterização em atmosfera de nitrogênio (N2). Microscopia Eletrônica de Varredura (MEV), Difração de raios X (DRX) e difração a laser foram usadas para avaliar as características dos pós processados e dos compósitos sinterizados. Os pós processados foram compactados e sinterizados visando obter pastilhas dos compósitos para a caracterização mecânica via ensaios de microdureza. Validou-se a técnica de Metalurgia do Pó (MP) como uma técnica bem sucedidada para a fabricação desses compósitos.

Aug 16, 2017

By Caroline Gomes de Oliveira

Os impactos causados pela exploração dos recursos naturais pelo homem geram uma crescente inquietação em relação futuro do planeta a longo prazo. Assim, as fibras naturais vegetais ganham destaque como material de reforço por suas boas propriedades mecânicas, baixo custo e por serem biodegradáveis. Umas das fibras que mais ganhou destaque nas últimas décadas é a fibra de rami, objeto de inúmeros estudos. Neste trabalho, analisou-se o efeitodo tecido produzido com a fibra de rami como reforço para a matriz epóxi sob esforços de impacto Charpy e Izod. A metodologia utilizada foi a produção de placas laminadas sob afeito de vácuo. Os resultados mostram notável diferença na resistência ao impacto do compósito comparado à matriz sem reforço.

Oct 30, 2017

By Ricardo Melo Pereira

Este trabalho tem como objetivo avaliar modelos de simulação, construídos através do software Talpac® em uma mina a céu aberto, a fim de analisar através de distribuições de probabilidade com o uso do software Minitab®, alguns parâmetros que influenciam diretamente a produtividade dos caminhões fora de estrada. Dentre estes parâmetros, os principais são: Carga média dos caminhões, velocidade média, número de viagens por hora de trabalho e tempo médio de fila na carga. Ao final, os dados de produtividade dos caminhões obtidos no modelo, serão comparados aos dados reais da mina, obtidos através do sistema de gerenciamento de frota Smartmine®, podendo este modelo ser validado ou não, tanto em termos de produtividade quanto dos demais parâmetros.

Aug 16, 2017

By João Vinícius de Souza Vares

O presente trabalho apresenta um estudo acerca da trefilabilidade de arames de aço semelhante ao SAE 1045, que são destinados ao atendimento da demanda do setor agropecuário. O trabalho envolveu a análise da produção dos arames a partir de matéria-prima advinda de aciaria elétrica, além das condições dos processos de conformação. O processo de trefilação foi mantido invariável, com as mesmas condições e parâmetros de reduções e lubrificação. Verificou-se a viabilidade de trefilação de ambos os materiais e a influência da maior fração volumétrica de perlita, através de análises conjugadas de propriedades mecânicas e condições microestruturais, resultando em valores mais elevados de resistência mecânica e menores valores de alongamento para os arames.

Oct 30, 2017

By Felipe Fardin Grillo

A cal e a fluorita são os principais componentes das escórias dessulfurantes. Entretanto, a busca por tecnologias consideradas menos poluentes vem tomando espaço neste setor. Dessa maneira, a necessidade de desenvolvimento dos processos faz com que as usinas siderúrgicas busquem melhorias no processo. Neste contexto, este trabalho tem como objetivo realizar um estudo de substituição da cal convencional por resíduo de mármore e também da fluorita por aluminato de cálcio. Os ensaios foram realizados a 1.600°C e as amostras foram retiradas periodicamente durante 25 minutos afim de se avaliar a dessulfuração ocorrida no metal. Os resultados indicam a viabilidade da utilização do resíduo e do aluminato de cálcio em escórias dessulfurantes para aço.

Aug 8, 2018

By Saul Garcia Hernandez

The research work objective is to study a new ladle shroud internal design to reduce the slag emulsification in the tundish during ladle transient periods. A 3D mathematical model of the tundish was created to solve the fundamental equations, a turbulence model, and a multiphase model. The results show that using a conventional ladle shroud, the fluid is delivered with an excessive amount of kinetic energy being dissipated inside the tundish bath, generating strong mixing flow patterns and entrapping a massive amount of slag. In the other hand, the proposed ladle shroud dissipates the kinetic energy before the fluid enters the tundish promoting less intense mixing patterns; thus, the amount of slag emulsification is reduced significantly. Consequently, if the internal design of the ladle shroud is able to dissipate the kinetic energy before the fluid enters the tundish, it shall be possible to reduce considerable the slag emulsification and the slag opening area.

Aug 17, 2017