Search Documents

By G. K. Manning, W. E. Few

T has been known for some time that both'inter-granular carbide and intergranular oxide phases cause brittleness in molybdenum. Parke and Ham' indicated that 0.0025 pct 0 present in molybdenum after solidification from the melt was sufficient to induce intergranular brittleness during forging. However, material containing 0.06 pct C could still be forged. However, adding this amount of carbon to insure deoxidation causes the formation of carbides on freezing. These carbides are precipitated at grain boundaries, and Rengstorff and Fischer' have shown they have an unfavorable effect on the room-temperature ductility of molybdenum. Take? in 1928 proposed that the solubility of carbon was a constant value of 0.30 pct from room temperature up to 1800°C. In 1935, Sykes, Van Horn, and Tucker' obtained X-ray data suggesting that the solid solubility of carbon in molybdenum was between 0.07 and 0.09 pct at temperatures from 1500" to 2100°C. The a-solubility line for carbon was included in the Mo-C diagram given in the Metals Handbook as a tentative line based on the data of Sykes, Van Horn, and Tucker. In order to determine the partial phase diagrams for these systems, it was necessary to construct a high-temperature furnace suitable for heat treating molybdenum at temperatures up to 4000°F. A molybdenum resistance furnace was built for this purpose in which samples could be heat treated in a purified atmosphere and quenched from any desired temperature.' Experimental Work Solubility of Carbon: Arc-cast molybdenum supplied by the Climax Molybdenum Co. and 18-gage molybdenum wire samples produced by powder metallurgy at the Fansteel Metallurgical Co. were used in determining the a-solubility line for the MO-C system. The cast molybdenum contained 0.032 pct C initially. Two lots of 18-gage wire were used, one containing 0.011 pct C and the other 0.005 pct C initially. All material contained a carbide phase as received. Fig. 1 illustrates the carbides found in the untreated material. Heat treatment in a purified hydrogen atmosphere was found to reduce the carbon content in the as-cast molybdenum. Purified argonT also decarburized molybdenum samples at temperatures above 3500°F; however, the carbon content remained constant during heat treatment in purified argon at lower tem- peratures. The argon was purified by passing it over titanium at 750 °C and then through a magnesium perchlorate drying tower. The hydrogen was purified by passing it through a commercial hydrogen deoxidizer, followed by a drying tower. Specimens having different initial carbon contents were heat treated in argon at 3500°F for periods ranging from 5 min to 5 hr and were analyzed for carbon. Samples of the same final carbon content had the same microstructures regardless of time at temperature. Furthermore, a gradient between center and surface in the amount of undissolved carbide particles present was never observed. It was concluded that at these low carbon levels, and at the high temperatures involved, diffusion proceeds so rapidly that the specimen is always substantially homogeneous in carbon content, in spite of the gradual loss in carbon. Based on the above findings, the following procedure was used to determine the carbon-solubility limit at 3000°, 3500°, and 4000°F. At each of these temperatures, a number of samples were heat treated, as shown in Table I, and rapidly cooled to room temperature. Since the samples lost carbon in proportion to the length of time heated, a series of samples were obtained of varying carbon contents. By use of a rapid cooling rate, the phases present at the high temperature were retained at room temperature. All samples were examined microscopically. Those found to contain either no excess carbide phase or only a very small amount were then analyzed for carbon. The samples actually analyzed for carbon

Jan 1, 1953

By W. E. Rice

THE ceramic industry has to do with forming or molding articles of clay, and imparting to them their characteristic properties of permanence, strength and color by subjecting them to heat treatment in kilns. This heat treatment is commonly known as "firing" or "burning." The art of firing clay ware antedates the industrial use of coal; hence wood was the fuel first used, and the earliest kilns were built to burn wood. The majority of the clay ware produced today is fired in periodic kilns that are essentially enlarged structures similar to the earliest enclosed kilns; a kiln consists of a large chamber 16 to 32 ft. dia. (or rectangular) in which the ware is charged and fired either in direct contact with flame or hot gases from the fuel, or in saggers which shield the ware from direct contact with the gases. The fuel is burned in a number of small furnaces built in the thick .wall that encloses the chamber; these furnaces are from 16 to 36 in. wide and from 3 to 5 ft. long; some of them have horizontal or sloping grates, but many have no, grates; the last are called "dead-bottom" furnaces. The temperature necessary to mature the charge in the kiln varies for different clays; for some it is as low as 1800°, and for others as high as 2700° F. Wood was an ideal fuel for the low temperatures that were used in early kilns; it burns freely and produces along, clean flame, which promotes uniform distribution of the heat in the kiln; it does not coke and so restrict the passage of air through the fuel bed; the ash does not melt in the fuel bed to form clinker; and the ash that is carried into the chamber and deposited on the charge does not contain iron and sulfur to discolor the clay. The extent of the ceramic industry now precludes the general use of wood in kilns, so that today this industry is one of the large users -of bituminous coal, burning more than eight million tons annually in kilns. Manufacturing plants usually are at or near the source of clay, with deposits of coal suitable for kilns occurring near the clay. The cost of coal is the largest single item of expense in the manufacture of clay ware, and, because all coals are not equally suitable for the process, the careful selection of coal is important. In this selection the desidera-

Jan 1, 1932

By Clement K. Chase, F. Milton Lewis, Roshan B. Bhappu

In situ extraction for copper, gold and uranium, generally involves several common alternative processes and techniques. These include dump leaching, heap leaching, leaching of fractured ore in-place or bore hole mining and unit operations such as cementation, solvent extraction, ion-exchange or carbon-in-pulp. Since the metallurgical effectiveness and economics of such processes and unit operations are well established, it would be possible to select the optimum alternative for extracting either copper, gold or uranium from their ores using in situ extraction technology. In this paper, efforts have been made to provide metallurgical evaluation as well as capital and operating costs for the various processes and unit operations. Attempts have also been made to utilize the above costs in preparing feasibility studies for in situ extraction of these metals.

Jan 1, 1976

By W. B. Devereux

I have observed three deposits of iron ore in Pitkin County, which present unusnal characteristics, and wliich seem to throw some light upon the genesis of iron ores under certain conditions. They occur in the precipitons mountain ranges, forming spurs on the Pacific slope of the main continental backbone. The first is a body of limonite, lying upon the side of a high mountain, which forms part of the base of Hayden's Peak. This limonite forms a sheet of considerable area, and is thin at the edges, and about 3 feet in thickness in the central portions. It is conformable with the slope of the mountain side, and rests upou the eroded rocks, but is not comformable to them. The ore is laminated and shaly in texture, and has the physical characteristics of the hard limonites, such as are found in the Marquette District, Lake Superior. It is covered with loose earth and rocks, from 1 to 2 feet in thickness. Much of the ore is filled with impressions of' spruce leaves, such as are found in the forests now covering the slope of the mountain. In the rocks forming the mountain, iron pyrites occurs in bodies, and this limonite probably owes its origin to such a body not far distant. Not far up the mountain large masses of conglomerate are now forming, the cementing material being a similar hydrated oxide of iron. The iron is

Jan 1, 1884

By William Vietti

WEST TEXAS and New Mexico has been overshadowed by the develop-ment in East Texas to such an extent that the area has been placed on a settled production basis by most of the operators. Considerable develop-ment work on both proven and unproven acreage remains to be carried on, but the incentive, a ready and profitable market, has been lacking. The main characteristics of the fields in this area are so well known that they are not described again in this paper, which thus resolves itself into a statistical review of the more important production features of the area. Proration has been in effect during the year and has been rigorously applied with the full cooperation of all producers. Proration in West Texas and New Mexico is based in the more pro-ductive fields on a potential and acreage distrbution of the allowance to the individual wells or acreage units. Potentials are determined generally by a short production test of from 1 to 4 hr.; and the hourly rate is multiplied by 24 to obtain the 24-hr. production or rated potential of the separate wells. The potential values thus set up have been questioned by many production men who are not willing to concede that the instantaneous (hourly) capacity of a well to produce is its potential capacity for a day with all other wells in the pool producing at their capacity. However, the potential of a well determined as above remains its chief rating as a measure of the permeability in place and as an indication of the possible reserve feeding that well. , The acreage factor has made it unnecessary to overdevelop properties in order to obtain an allowance proportionate to neighbors who are willing to drill an excessive number of wells on a piece of acreage in the hopes of a quick drainage and a corresponding profit. Proration has resulted in an orderly development of many of the pools in this area on the base as out-lined above, resulting in more reasonable spacing of wells and the more even withdrawal of oil and the ensuing expectation of high recoveries.

Jan 1, 1933

By Erwin Zodrow

An elaborate model for the magnetite distribution and genesis in the Smallwood mine, Labrador, based on factor analysis with orthogonal and oblique rotation of the factors, was proposed in an earlier paper. However, it is implicit in that model that variances of one variable shared with all others (communality) are estimated. To avoid the problem of communality estimation in the present investigation, a different type of factor analysis is used which (1) emphasizes the shared variances, and (2) attempts to eliminate, as much as possible, errors associated with the estimation of communality and sampling (unique variance). The samples for the present analysis are not the commonly employed oxide percentage variables, but counts of mineral species in specified areas of thin sections from drill core in the Smallwood mine: quartz, magnetite, calcite, and specular-hematite minerals. The counting procedure for mineral species is similar to modal analysis differing from it principally in the aspect of texture recognition. The constant area in which mineral species are counted is dependent primarily on

Jan 1, 1975

By M. D. Cooper

UNDERGRADUATES in mining engineering may be prepared for work by giving them sound instruction in the courses generally considered essential to the profession. The industry is not deeply concerned about the details of those courses. The average man in the coal industry does not wish to insist upon a rigid program. Therefore, he differs little from those in the teaching profession who evidently are not unanimous in their opinions, or all college catalogs would be alike. For the good of the profession, it is just as well that there should be differences in regard to details. It appears that students graduating in mining engineering from the accredited institutions receive similar instruction. It is taken for granted that the graduate will have a good understanding of English, mathematics, mechanics, electricity, chemistry, physics, geology, and surveying, in addition to his major courses in mining. Somewhat belatedly, industry hopes he will have had at least an introduction to the subject of labor relations, the importance of which is only too clear at present. The coal industry expects, of course, that students in mining engineering will be taught the strictly mining subjects by men who have had practical experience in the mines and who keep themselves well informed in regard to current methods. While the undergraduate is subject to the control of members of the teaching profession, industry expects him to be trained in certain ways that are not a part of his textbooks, but can be made an inseparable part of his development by the skillful supervision of his teachers. Of the desired characteristics, dependability is of the utmost importance. Probably most employers would overlook certain short-comings if the young graduate demonstrated that he was thoroughly dependable. If he always appeared at the right place at the right time with the proper equipment, he would soon be well established as a welcome member of his organization. The graduate who gets a reputation for being undependable will have little opportunity for advancement. Closely allied to dependability is loyalty. Athletic teams and social groups in college tend to develop loyalty which may well be carried over into industry. This does not mean that the graduate has to be satisfied with customary practices. The average manager is glad to see the graduate make constructive criticism as long as he demonstrates his loyalty at the same time. It is important that his loyalty keeps him alert arid ready to take helpful action for the benefit of his organization, and especially to stand with it during times of stress. With or without an introduction to labor relations in college, the graduate is expected to develop ability in this most important field. Beginning with himself, he will find it essential to deal agreeably with his immediate associates. Getting along in friendly fashion with his own small group will be a great help as his responsibilities increase and he is required to deal with larger numbers of persons. On a higher scale, his interest in his community may grow at the same time by voluntary work in any one of a great number of useful activities. Industry expects the graduate engineer to be a mature man at the time he gets his first job. Supposing that he has better than average intelligence, industry expects him to continue to grow intellectually and to fit himself for responsible jobs when they are offered to him. For this reason, employers are apt to look over his college record to see what he did that would indicate his fitness for leadership. There is interest in knowing what he did beyond the requirements. As evidence of his mental growth, it is expected that the graduate will do independent thinking; that he will not take too much for granted. When he reads a report, he should develop the ability to see whether the subject is new or whether it is just a description of an old method that has been superseded by something better. For the same reason, the graduate should be able to accept conditions that have been arrived at by sound experience rather than cling to something else that seems better in theory. In this connection, it may be remarked that the ability to operate successfully a personal budget will be noteworthy, as it may be assumed that a man who knows how to conduct his own affairs will be prepared to assume the larger responsibilities of industry. Membership in AIME will indicate to the employer that the graduate is interested in the mining industry as a whole. Therefore, it is good evidence of something more than a local outlook. Quite apart from college training and mental ability, the newly employed graduate will be expected to be willing to do hard manual labor for a time. This will give him an understanding of the actual conditions of work done by those he supervises later. He will gain their confidence and be able to see that the work is carried on in a safe and efficient manner. Part of this experience may be acquired in his summer vacations during his undergraduate career. Such work would make a favorable impression on a prospective employer, especially if the graduate showed a willingness to continue it until he was prepared for something better. To summarize, the man in authority in the coal industry will not quarrel with the professor of mining engineering over details of curriculum. He will be pleased if the school sends him graduates who possess a good foundation in the courses studied, and who may be depended upon to do their work faithfully and intelligently. Such men will be ready when the time comes to assume their places as leaders of an essential industry.

Jan 1, 1951

By M. D. Cooper

UNDERGRADUATES in mining engineering may be prepared for work by giving them sound instruction in the courses generally considered essential to the profession. The industry is not deeply concerned about the details of those courses. The average man in the coal industry does not wish to insist upon a rigid program. Therefore, he differs little from those in the teaching profession who evidently are not unanimous in their opinions, or all college catalogs would be alike. For the good of the profession, it is just as well that there should be differences in regard to details. It appears that students graduating in mining engineering from the accredited institutions receive similar instruction. It is taken for granted that the graduate will have a good understanding of English, mathematics, mechanics, electricity, chemistry, physics, geology, and surveying, in addition to his major courses in mining. Somewhat belatedly, industry hopes he will have had at least an introduction to the subject of labor relations, the importance of which is only too clear at present. The coal industry expects, of course, that students in mining engineering will be taught the strictly mining subjects by men who have had practical experience in the mines and who keep themselves well informed in regard to current methods. While the undergraduate is subject to the control of members of the teaching profession, industry expects him to be trained in certain ways that are not a part of his textbooks, but can be made an inseparable part of his development by the skillful supervision of his teachers. Of the desired characteristics, dependability is of the utmost importance. Probably most employers would overlook certain short-comings if the young graduate demonstrated that he was thoroughly dependable. If he always appeared at the right place at the right time with the proper equipment, he would soon be well established as a welcome member of his organization. The graduate who gets a reputation for being undependable will have little opportunity for advancement. Closely allied to dependability is loyalty. Athletic teams and social groups in college tend to develop loyalty which may well be carried over into industry. This does not mean that the graduate has to be satisfied with customary practices. The average manager is glad to see the graduate make constructive criticism as long as he demonstrates his loyalty at the same time. It is important that his loyalty keeps him alert arid ready to take helpful action for the benefit of his organization, and especially to stand with it during times of stress. With or without an introduction to labor relations in college, the graduate is expected to develop ability in this most important field. Beginning with himself, he will find it essential to deal agreeably with his immediate associates. Getting along in friendly fashion with his own small group will be a great help as his responsibilities increase and he is required to deal with larger numbers of persons. On a higher scale, his interest in his community may grow at the same time by voluntary work in any one of a great number of useful activities. Industry expects the graduate engineer to be a mature man at the time he gets his first job. Supposing that he has better than average intelligence, industry expects him to continue to grow intellectually and to fit himself for responsible jobs when they are offered to him. For this reason, employers are apt to look over his college record to see what he did that would indicate his fitness for leadership. There is interest in knowing what he did beyond the requirements. As evidence of his mental growth, it is expected that the graduate will do independent thinking; that he will not take too much for granted. When he reads a report, he should develop the ability to see whether the subject is new or whether it is just a description of an old method that has been superseded by something better. For the same reason, the graduate should be able to accept conditions that have been arrived at by sound experience rather than cling to something else that seems better in theory. In this connection, it may be remarked that the ability to operate successfully a personal budget will be noteworthy, as it may be assumed that a man who knows how to conduct his own affairs will be prepared to assume the larger responsibilities of industry. Membership in AIME will indicate to the employer that the graduate is interested in the mining industry as a whole. Therefore, it is good evidence of something more than a local outlook. Quite apart from college training and mental ability, the newly employed graduate will be expected to be willing to do hard manual labor for a time. This will give him an understanding of the actual conditions of work done by those he supervises later. He will gain their confidence and be able to see that the work is carried on in a safe and efficient manner. Part of this experience may be acquired in his summer vacations during his undergraduate career. Such work would make a favorable impression on a prospective employer, especially if the graduate showed a willingness to continue it until he was prepared for something better. To summarize, the man in authority in the coal industry will not quarrel with the professor of mining engineering over details of curriculum. He will be pleased if the school sends him graduates who possess a good foundation in the courses studied, and who may be depended upon to do their work faithfully and intelligently. Such men will be ready when the time comes to assume their places as leaders of an essential industry.

Jan 1, 1951

By O. U. Bradley

The extent of losses, due to evaporation, sediment, and water, in crude oil stored in steel tanks, is a very interesting question, and particularly so at this time, when every reasonable measure should be employed to eliminate all possible losses of this important natural product. Available information on this subject is incomplete; e.g., during the development of the Cushing Field, considerable surplus oil was stored in steel tanks, but from time to time, owing to changes in weather, some losses by evaporation and short storage room on the leases, these tanks were topped out, thus rendering inaccurate any system designed to determine the average rate of evaporation or other losses of the oil over a given period. Furthermore, the losses, as shown by the records at the time, as a result of hasty gages, failed to take into account the temperature and gravity of the oil. Losses may be classified roughly as occurring from evaporation, presence of sediment and water, and leakage. The coefficient of expansion and contraction of crude oil, in relation to temperature conditions, is of material importance; also, the rate of evaporation is dependent upon the gravity of the oil, as the escape of the lighter hydrocarbons in fresh Cushing oil, of from 40 to 42 gravity, on a warm day is considerable, and from available records of temporary storage, it is safe to assume that a loss of 1 to 11/2 per cent. in volume will easily occur in light crude oil of Cushing grade over a period of 6 months, including the summer season. The presence of sediment, water, and other impurities, in the oil will also cause more or less deterioration in quality, particularly when the fresh production is run direct from the gage tanks, or from the wells on the lease to steel storage, as is often the case when an oil field is being rapidly developed. The bad oil will settle to the bottom of the tanks and may be determined by thiefing and running a centrifuge test on the sample. The amount of water in the oil depends entirely on the conditions under which it is produced. Sometimes in large producing wells, with heavy gas pressure, some water may come in with the oil, particularly if the well has been drilled to the top of a water sand. Under these conditions, cut oil is often produced, which, if not settled out, is carried over into the steel tanks. The losses by leakage in steel tanks are difficult to determine, for

Jan 1, 1920

J. E. JOHNSON, JR., New York, N. Y. (communication to the Secretary*).-The discussion of Mr. Henrich's paper took place at a meeting from which I had the misfortune to be absent, and has just come to my attention. I do not wish to let the subject pass without contributing to it a little information which has come into my possession. In 1912, I published a brief note in the Transactions on The Effect of Alumina in Blast-Furnace Slags, giving in tabular form three typical slags used in iron blast-furnace practice, one of them the high alumina slag of, which Professor Richards speaks. That table is reproduced herewith. TABLE 1.-Composition of Slays. 1 3 3 4 5 6 7 CaO by Neutral Ratio Ratio Ratio Al2z03, SiO2, Differ- Substan- Cat Ca0 a A1203 Ratio Per Per ence, ces, CaO Cent. Cent. Per Per Al2O3 + Sioz Sit: SiO2 Cecil_ Cent. Virginia practice 6.5 36.0 54.0 3.5 1.27 1.6S 1.50 Lake-ore practice 13.5 33.0 50.0 3.5 1.08 1.92 1.51 Special experiment... 36.0 24.7 36.8 3.5 0.59 2.90 1.44 It supplies what seems to me convincing evidence that, for the purposes of the iron blast furnace, alumina can be regarded only as a neutral substance, dissolving in the slag and materially altering its viscosity, but not affecting its chemical activity. In subsequent experience with charcoal furnaces, I found the same rule to hold; that the chemical effect of alumina could be disregarded, providing the ratio of the lime and magnesia to the silica were kept constant. This is exactly the experience which Messrs. Dwight and Mathewson had in copper- and' lead-smelting furnaces. I have never seen any evidence or argument adequate to support the contention of Professor Richards-that the alumina acted as a base in the charcoal iron furnace and as an acid in the coke furnace, and that the function of alumina in iron-furnace slags is inherently different from that in copper- and lead-furnace slags-and I am compelled to differ absolutely with his conclusions in that respect.

Jan 9, 1917

By Dewitt T. Ring

Reliable and detailed data covering the enormous number of wells drilled and the long historical production of the state, many of which were never recorded until recent years, render it impossible to gather statistical material suitable for the Institute's standardized form. The total production of crude oil in Ohio for the year was 3,654,503 bbl., which is less than the total production in the United States for the peak day of August 1937. For a period of eight years, from 1895 to 1902 inclusive, Ohio produced more oil than any other state. During the year, 1271 tests were drilled in the state, or 114 more than in 1936. Of these, 317 were oil wells, with an initial production of 7088 bbl., an average of 22.3 bbl. per well; 503 were gas wells, with an initial open flow of approximately 222,441 M cu. ft., or 443 M cu. ft. per gas well drilled; 451 were dry holes, that is, 35 per cent of the total completions. A number of factors account for the steady decline of oil production in Ohio. In the state, at the close of thc year, there were fewer than 28,122 producing oil wells. In 1936, there were 30,150 operated oil wells with an average yearly production per well of 126 bbl. The production for 1937 averaged 130 bbl. per well. During the year, 2028 oil wells were abandoned. In other words, old wells are being abandoned more than six times faster than new ones are being drilled. Since the inception of the oil and gas industry in Ohio, between 150,000 and 160,000 wells have been drilled in the state; new potential territory, offering desirable locations for either oil or gas, is becoming increasingly more difficult to find; the dry-hole percentage will continue to increase. Prices Another factor directly affecting the crude situation during the year was the matter of price and proration of Pennsylvania grade oil. The posted price for Pennsylvania grade in Ohio on June 7 was $2.37 per barrel; at the close of the year, it was $1.70 per barrel, or a reduction of 28 per cent in price. In addition to this price cut, a 50 per cent pro-

Jan 1, 1938

By Lewis T. Wright

I have long been aware that ferruginous copper furnace-slags if fused in the electric arc will yield metallic iron containing copper, and in order to confirm this knowledge, and to obtain further information of the behavior of such slags in the high temperature and reducing conditions of the electric furnace, a number of samples of slag were fused in an experimental electric furnace. The results obtained, given in Table I., show that a very large amount of metallic iron was produced, and that this iron carried with it practically all the copper, gold, and silver, and more than 50 per cent. of the sulphur, of the original slag. The metallic buttons formed in the electric furnace were clean, hard, but not brittle.

Jan 1, 1911

By P. Duwez, L. Zwell

L. S. BUSCH—We have had presented two methods of measuring these variations in powder compacts. E. OROWAN—Tn connection with the rolling mill research work carried out at. the Cavendish Laboratory, Cambridge, with the help of the British Iron and Steel Research Association. Dr. E. A. W. Hoff, Mr. J. Los, and myself, have determined coefficients of friction at ex- treme pressures for a number of liquid and solid lubricants, both by direct measurement, and by calculation from measured values of the roll force. The most efficient lubricants at these high pressures (for the small amounts of sliding that, occur in rolling) were camphor and. in particular, borneol (Borneo-camphor). Perhaps such lubricants could be used with advantage in the kind of work described by Dr. Wulff. L. S. BUSCH—1 think Dr. Wulff has in the past mentioned experiments which have been performed in the extrusion and rolling of metals and which led to conclusions which can be applied to the compacting of metal powder. A. SQUIRE*—There have been some recent developments in the field of high pressure lubricants which indicate that boron nitride might be a very desirable material to employ as a die lubricant. At the present time its cost is prohibitive, but as the need arises for the material it will undoubtedly come down in price. The present price is $200. a pound. It is my understanding that one of the reasons for vacuum pressing both in ceramics and metal powders, is to prevent

Jan 1, 1950

By M. S. King, B. N. P. Paulsson

Four vertical boreholes in the vicinity of an electrical heater simulating a canister of nuclear waste in a granitic rock mass have been logged with an acoustic borehole sonde before and after thirteen months' heating. Excellent control of the structural geology and fractures present in the rock mass was provided by the considerable amount of oriented core recovered from the four boreholes used for acoustic logging and the large number of others used for a variety of rock mechanics instrumentation. Compressional and shear-wave velocities were measured as a function of stress on some twenty core samples, water-saturated and dry, which were recovered from the four acoustic logging boreholes. Further control was provided by a cross- hole acoustic monitoring program conducted before, during and after heating between the same four boreholes, and by measurements of acoustic velocities in an isolated block of granite in the same heater drift, which was subjected to an increase in temperature and to changes in uniaxial stress. It is concluded from the acoustic logging tests, taken in conjunction with the acoustic cross-hole and heated block experiments, that acoustic techniques: 1. Provide a means for locating and delineating systems of weakly- bonded or open fractures within the rock mass; 2. Provide a sensitive means for monitoring a rock mass for changes in moisture content or structural damage to the rock fabric induced by thermal or mechanical loading; 3. Together with the rock bulk density yield the elastic constants of the rock mass.

Jan 1, 1982

By Frank Hultgren

The influence of grain boundaries and polygonized subsructure on the flow stress of commercially pure aluminum has hem studied. A systematic inz-estigoti017 of grain size and subgrain size and mis-orientation was pursued; the contributions of pain boundary md substruture hardening were found to he additive fuiictions. Subgrain boundaries exert greater influence on hardening at room temperature than do grain boundnries. Both subgrain diameter and misorientation influence flow stress, but only to the extent that both contribute to the dislocation density. The flow stress due to substructure may he described by the equation of = abp1/2. THE origin of substructure hardening in metals has remained unclear for a long time. Lately, both theory and experimental techniques have become more exact and merit a closer examination of the subject. In the present work, the influence of polygonized substructure size and misorientation in commercially pure aluminum on mechanical properties has been systematically investigated. The influence of substructure on mechanical properties has been compared with that of grain boundaries. In addition, the works of several authors are compared with theoretical predictions of substructure hardening. EXPERIMENTAL TECHNIQUES Aluminum of 99.9 pet purity (0.04 Fe, 0.046 Si, 0.00 Cu) was employed. Various grain sizes were produced by heavy (over 90 pet reduction in area) cold drawing and recrystallization at various temperatures. A (111) fiber texture was observed in all specimens. Grain sizes were analyzed statistically. Substructure of varying size and misorientation was produced by prestraining specimens of various recrystallized grain sizes. Specimens for mechanical testing and substructure analysis were recrystallized, prestrained, and annealed together. The samples were prestrained from 5 to 25 pet in tension at room temperature and annealed at 200" to 370°C for 2 hr. All samples were rapidly cooled (in air) from the anneal to retain the subgrain wall structure developed at the annealing temperature. A clearly polygonized substructure was developed in all cases. Substructure size was measured by the Berg-~arrett' technique and analyzed statistically. Substructure misorientation was measured in the following manner. Individual grains in the polycrys-talline aggregate were isolated and their intensity distributions mapped using an X-ray goniometer and Geiger counter. From the observed profiles, the

Jan 1, 1964

By J. E. Miller, W. E. DeVaney, L. Stroud

During a recent phase study of a natural gas, two stable equilibrium liquid phases were observed at temperatures below —200°F and pressures above 200 psi. This paper reviews the published literature on the occurrence of multiple equilibrium liquid phases and presents analytical data for the vapor and two equilibrium liquid phases of the liquefied natural gas at five experimental conditions. In addition, data for 30 conditions of two-phase equilibria are included. INTRODUCTION The low-temperature phase behavior of gases, most of which contained helium, has been investigated in the laboratories of the Helium Activity for many years. Since 1952, experimental studies of these systems have been continuous as part of the research program at Amarillo, Tex. Because of their value to private industries interested in participating in the Helium Conservation Program, several "Open File" reports containing phase equilibria data for heliurn-bearing natural gases have already been released by the Helium Activity. A paper containing information on the general phase behavior, operating criteria and extensive vapor-liquid data for two helium-containing systems was recently published.2 Additional publications presenting experimental data on the phase relationships of various gas systems are now in process and will be available in the near future. PREVIOUS EXPERIMENTAL WORK Although the formation of multiple liquids has been reported for various systems, to our knowledge this paper is the only substantiated evidence of a vapor-liquid-liquid equilibria in a naturally occurring gas. In 1940, Vink, Ames, and others13 reported the presence of two liquid phases in a hydrocarbon system consisting of mixtures of crude oils, solvents and natural gas. Eilerts and co-workers; published data on the recombined fluids from a gas-condensate well. This condensed gas, containing approximately 76 per cent methane and 24 per cent ethane-plus, exhibited two distinct liquid phases. Weinaug and Bradley 14 observed "unusual" phase behavior in a reservoir mixture. These workers postulated that the anomalous phase behavior was due to the "imminent formation of a second liquid phase". Botkin, Reamer, Sage and Lacey 1 studied two California crude oils that exhibited multiple phases. Kohn and Kuratal0 recently reported two equilibrium liquid phases in the methane-hydrogen sulfide system. Roof and Crawfordl1 and Eakin, et a16 also have reported experiments with binary systems that formed two stable equilibrium liquid phases. APPARATUS AND PROCEDURE A U. S. Bureau of Mines Phase Equilibrium Apparatus was used in conducting this study. The apparatus and procedures employed in its operation have been previously described3 and will not be repeated in detail ill this report. Briefly, the apparatus consists of a windowed cell which can be maintained within ±0.5°F for temperatures between room temperature arid -320°F. Pressure within the cell can be maintained within 0.1 per cent of gauge reading up to 800 psig. Equilibrium vapor and liquid samples are obtained in special containers4 for analysis by a mass spectrometer. Although the accuracy of the analyzer is about ±0.1 mol per cent, the reproducibility of the phase-equilibrium apparatus is considered relatively poor. Values reported from methane and nitrogen are considered accurate to ±l.0 and ±0.6 mol per cent. Data for ethane-plus in the vapor are accurate within 0.2 mol per cent; liquid-phase data for this aggregate compolnent are accurate within 1.5 mol per cent. For helium in the vapor phase, the analytical data are accurate within 0.2 mol per cent; liquid-phase analyses for this component were obtained by the charcoal adsorption method described by Frost8 and are accurate within 0.006 mol per cent. All of these references to the accuracy of reported values are conservative estimates based upon a statistical treatment of reproducibility data obtained with the apparatus.

By T. M. Geffen, J. L. Sanderlin, F. F. Craig, D. W. Moore

Scaled reservoir models have been used to study the effect of gravity on oil recovery performance in frontal-drive operations; namely, water, gas, or solvent flooding. The difference in density between the reservoir oil and the injected fluid causes their segregation, resulting in a non-uniform advance of the fluid front. In the laboratory flow tests, which simulated both five-spot and linear injection operations in flat reservoirs, the viscous, capillary, and gravity forces present in these operations were scaled. Dyed fluids were used so that the gross movement of the injected fluid could be observed. The studies covered a range of injection rates, formation thicknesses, and rock and fluid properties normally encountered in field operations. The results of the model tests indicate that the volume of the reservoir contacted by the injected fluid at its breakthrough into the producing well is less than that expected based on information which neglects gravity effects. This difference can often be as much as 80 per cent by gas or water injection in uniform sand bodies. Preliminary flow tests on a non-uniform sand body indicate that the uniformity of the flood fronts may in some situations be influenced to a much greater degree by permeability variations within the rock body than by gravity effects. The magnitude of fluid segregation due to gravity is controlled by the average injection rate, rather than day to day or week to week variations. INTRODUCTION One of the important factors controlling the oil recovery from a frontal-drive operation, such as water, gas, or solvent injection, is the volumetric sweep efficiency. This factor is a measure of the gross portion of the reservoir that is contacted by the displacing fluid. The volumetric sweep efficiency is influenced by gravity effects, well arrangements, and variations in rock permeability within the reservoir. The gravity effects are due to the displacing fluid being of different density than the reservoir oil. This causes the displacing fluid to move preferentially toward either the top or bottom of the formation. Non-uniform advance of the flood front can be caused by the relative positions of the injection and production wells. Variations in rock permeability also result in an uneven advance of the displacing fluid. Gas zones, representing paths of low resistance, may result in non-uniform movement of the injected fluid. The more uneven the advance of the displacing fluid, the lower is the volumetric sweep efficiency and thus the lower the oil recovery efficiency. The effects of well arrangement and permeability variations, upon the gross movement of the injected fluid have been the subjects of extensive investiga-ti0ns.1,2,3,4,5,6 Gravity effects have been recognized as being present in frontal-drive operations'.' but there has been little quantitative measure of their magnitude. Very likely the reason gravity effects have not been studied is that this problem does not lend itself to simple experimental or mathematical analysis. The development of reservoir modeling techniques has made possible a quantitative determination of the effect of gravity on fluid segregation and thus upon the oil recovery performance of frontal-drive operations. This paper presents a progress report on a laboratory investigation of gravity effects in fully liquid-saturated, horizontal, uniform as well as non-uniform systems. These results were obtained from scaled experiments on both linear and five-spot systems within the range of conditions normally encountered in secondary recovery operations. This study is concerned with the gross movement of the injected fluid to the time it first reaches the production wellbore. Therefore, it should be emphasized that the results of this paper can not be used to determine the effect of gravity segregation on oil recovery efficiency at abandonment conditions. MODEL SCALING The science of scaling models is relatively new as applied as petroleum production problems, Many of the scaling techniques have been adaptions of those used in basic studies of heat and fluid flow. There are

Jan 1, 1958

By William F. Harris, Joseph Easha

FOR many years basic control of refinery operations depended on visual observation of small chill specimens poured at various intervals during processing. The oseto of these samples was related to the physical and chemical properties of the metal. Since the =setn is dependent on many factors other than oxygen content, this method, while giving a general indication of the condition of the copper, does not accurately measure the oxygen content. For the last 3 years a modified vacuum fusion procedure which enables the operator to determine the oxygen content of the copper within 1 5 min of sampling has been in use at the Westinghouse Copper Mill. For use with this apparatus a sampling technique has been developed which gives oxygen values representative of the oxygen content of the wire bar. The sampling technique is based on a statistical study, which compared the oxygen content of the laboratory sample of copper poured at the same time a wire bar was being poured, with the oxygen content of the wire bar. The apparatus used for the determination of oxygen in copper is shown in Fig. 1 and is essentially the same as previously described but with one important modification. A very porous fritted glass disc has been inserted in the tubing between the manom- eter and 40/50 ground glass joint. The fritted disc retains the copper vapor and copper particles in the furnace section and prevents contamination of the mercury in the manometer. Without the disc the manometer became difficult to read after a few weeks of operation. In earlier work1 it had been established that the simplified vacuum fusion apparatus used at the Copper Mill gave essentially the same results as a con-vential vacuum fusion apparatus. However, for this study it was necessary to determine the difference, if any, between the oxygen content of the wire bar and the oxygen content of the small chill sample used for the oxygen analysis. This correlation was established by taking a chill sample at the same time wire bars were being poured. The wire bar being poured at the time the chill sample was taken was marked and removed for further analysis. The copper is sampled at various times during refining and cast into laboratory size samples with the mold shown in Fig. 2. The mold is made of cold rolled steel and is 2 in. high and 2 1/2 in. in diam. The large upper portion of the cast sample is used for measurement of the conductivity of the copper, The lower portion which is a rod about 1/4 in. diam by 3/4 in. long is used for determination of the oxygen content. This portion of the sample weighs about 5 g which is approximately the size sample used for the analysis. The only preparation neces-

Jan 1, 1962

By John T. Galey

In all, 210 wellst were completed in southwestern Pennsylvania during 1939, which is 59 more than were drilled during the preceding year. Of this number, 137 were gas wells, which is a considerable increase from the 81 completed during 1938. Only 25 oil wells were completed, as against 28 in the previous year, and 28 dry holes, 6 more than last year. Shallow Development—Gas The increase in the number of gas wells is largely the result of a search for additional gas in Armstrong and Indiana Counties. Although a considerable number of wells were drilled in the latter county, the majority of them produced less than 100 M cu. ft. initial open flow. In Armstrong County, a new pool was opened in Cowanshannock township, producing from the third Bradford sand. Several large wells were obtained there, one of which produced an initial of nearly 12 million cu. ft., with a reservoir pressure of 1100 Ib. However, the productive area has been fairly well outlined by further drilling and shows that the pool covers only about 800 acres. The sand is 20 to 30 ft. thick, and probably has 5 to 6 ft. of pay. Thus this reserve is not an important one. Several wells were found in Menallen township, Fayette County, where the Big Injun sand has been having a play for the past three years, but the activity there is much less than a year ago. Oil On the west side of the Bradford sand gas pool, Cowanshannock township, Armstrong County, a well was drilled which flowed 100 bbl. the first day from the Tiona sand. The probability is that this well is a freak, as the Tiona has been drilled within a fairly close distance on every

Jan 1, 1940

By John T. Galey

In all, 210 wellst were completed in southwestern Pennsylvania during 1939, which is 59 more than were drilled during the preceding year. Of this number, 137 were gas wells, which is a considerable increase from the 81 completed during 1938. Only 25 oil wells were completed, as against 28 in the previous year, and 28 dry holes, 6 more than last year. Shallow Development—Gas The increase in the number of gas wells is largely the result of a search for additional gas in Armstrong and Indiana Counties. Although a considerable number of wells were drilled in the latter county, the majority of them produced less than 100 M cu. ft. initial open flow. In Armstrong County, a new pool was opened in Cowanshannock township, producing from the third Bradford sand. Several large wells were obtained there, one of which produced an initial of nearly 12 million cu. ft., with a reservoir pressure of 1100 Ib. However, the productive area has been fairly well outlined by further drilling and shows that the pool covers only about 800 acres. The sand is 20 to 30 ft. thick, and probably has 5 to 6 ft. of pay. Thus this reserve is not an important one. Several wells were found in Menallen township, Fayette County, where the Big Injun sand has been having a play for the past three years, but the activity there is much less than a year ago. Oil On the west side of the Bradford sand gas pool, Cowanshannock township, Armstrong County, a well was drilled which flowed 100 bbl. the first day from the Tiona sand. The probability is that this well is a freak, as the Tiona has been drilled within a fairly close distance on every

Jan 1, 1940