Search Documents

By F. H. Newell

In 1888 the United States Geological Survey began a systematic examination of the water-resources of the West, comparable in character and scope to the study of the deposits of ores or coal. As experience was acquired, the surveys were extended to the East, until now they embrace representative localities in all parts of the United States. The object to be attained is to note and record the distribution of water-supply, and to learn, as far as practicable, the laws governing its fluctuations.

Jan 1, 1901

By Wei-Kao Lu

A general rate equation is derived for gas -solid reactions in metallurgical processes by considering the contributions of chemical reaction at inter-phase boundaries and diffusion through the solid product layer simultaneously. This equation takes care of the whole range continuously from purely diffusion control to purely chemical reaction control. The parabolic law,' McKewan's equationa derived with the assumption of interface area control and the equation derived by Kawasaki et al. with the assumption of purely diffusion control are found as the limiting cases of the corresponding forms of the general rate equation. Many metallurgical processes involving gas-solid reactions have been extensively studied. The common examples of these processes include the reduction of oxides to metallic products, the roasting of sulfides to oxides or chlorides and the oxidation of metals. Gas-solid reactions consist of at least two kinds of steps; one involves the transport of reactant and product to and from the reaction zone and the other is the chemical reaction taking place at the interphase boundaries. In the limiting cases one or the other of the above mentioned steps will be much slower than the other and is then rate controlling. For example, the oxidation of metals is diffusion controlled and obeys the parabolic law.' On the other hand, if the diffusion rate is much larger than the chemical reaction rate then it will be controlled by the chemical reaction rate. This latter case occurs for the reduction of iron oxides studied by McKewan. If the rate of diffusion and of the chemical reaction have the same order of magnitude, a more detailed analysis is necessary. Thus at the beginning of the reaction when the solid and gaseous reactants are in direct contact, the reaction should be chemical reaction rate controlled as no diffusion process is involved. At the other extreme as the reaction zone moves further into the solid, the diffusion distance becomes greater and the diffusion rate continuously decreases. Eventually, therefore, for a sufficiently large sample the rate must become diffusion controlled. As the transition from one controlling step to the other must be continuous, we cannot describe this transition period by either of the two limiting cases. In this paper the author attempts to derive a general rate equation for gas-solid reaction systems. This is effected by considering the rates of diffusion and chemical reaction simultaneously from the state of pure diffusion control to pure chemical reaction control. I) DERIVATION The system under consideration is made of at least three phases, namely the gaseous one, the solid reactant, and the solid product as shown in Fig. 1. The notations are listed at the end of the paper. The mass transfer process involves the diffusion of reactants and products across the solid product layer. It is reasonable to consider that no chemical reaction will take place in the solid product layer with respect to both gaseous reactant and product. For the characteristics of local equilibrium of the system, the diffusion process is really in a quasi-steady-state. It will be proved in the following paragraphs. Then we can invoke the law of conservation of mass valid for all chemical species passing through the layer. The solid reactant sphere has an initial radius, ro, after a fraction of completeness of the reaction, the unreacted core has a radius ri, where r, is in the solid product region. Let Cg be the activity of gaseous reactant in the

Jan 1, 1963

By William P. Blake

The adaptation of aluminum to the construction of portable instruments of precision, where lightness is important, is well illustrated by the double reflecting and repeating circle, the invention of Captain Charles Hervey Tomnshend, of New Haven. One of these instruments, now exhibited to the members, has just been completed by Stackpole & Bro., of New York, and is made of aluminum, with the exception of a few minor pieces and a portion of the handle. This instrument is intended for use in a boat, and to be held in one hand like a sextant; and as it is a complete circle, lightness of the material becomes more important. The whole instrument, as shown, exclusive of the eye-pieces and the handle, weighs only one pound, or about one-third of the weight of a sextant of the usual construction. The circle, about nine inches in diameter, was cast in one piece from metal furnished by the Pittsburgh Company.

Jan 1, 1890

By N. Brown, J. Washburn, E. R. Parker

MOST previous quantitative work on creep of single crystals has been concerned primarily with developing empirical equations for the creep curve. Although the equations used by Cottrell and Aytekin¹ and Tyndall² represented the data quite well, it was often necessary to use different values of the constants for different specimens even though they were apparently tested under identical conditions. In the course of previous work on the effect of surface coatings on creep of zinc single crystals," it was found that equal resolved shear stress frequently did not produce equal creep rates in different specimens. The work of Chalmers' in the very

Jan 1, 1954

By R. Haynes

ON the basis of compositional changes of a phase observed in a eutectoid Cu-Al alloy1 it has been suggested that mechanisms for the decomposition of the ß phase proposed by earlier workers2-5 were incorrect. These data are reinterpreted in conjunction with lattice parameter data obtained on an alloy containing 12.2 pet Al, whose isothermal transformations have been reported elsewhere.5 The a Lattice Parameters of a 12.2 Pet A1-Cu Alloy—~iffraction patterns of completely transformed specimens were obtained in a back reflection camera using copper Ka radiation. Lattice parameters of

Jan 1, 1959

By Archibald Macmartin

THE Königin-Marien-Hütte is the only works in Germany where the Bessemer process is carried on by the direct method. The Besserner plant there, is arranged after the true English type, and the only resemblance to the Swedish mode of procedure is the dispensing with the use of spiegeleisen at the end of the "blow." In a new department of the establishment, started within three years, each of the converters is turned by means of a very neat and compact reversible engine, the steel shaft of which is an endless screw, which turns against the oblique cogs of a large wheel attached to the shaft of the vessel. An advantage which this arrangement possesses over the ordinary English hydraulic arrangement, is the fact that the endless screw suffices to turn the vessel, in either direction, any number of complete revolutions; while even the latest American improvements, so clearly explained to us by Mr. Holley at the opening session of this meeting, do not secure even one complete revolution without changing the angle of inclination of the hydraulic piston. In the endless screw arrangement, there being no limit to the working of the motor in either direction (no return-stroke necessary), the vessel can always, unless outside reasons demand the contrary, be turned around to any desired position by the shortest cut, whether backwards or forwards. Also, the diameter of the cog-wheel attached to the vessel can be made sufficiently great to avoid all unevenness of motion. In the old department the motive-power still continues to be hydraulic. If reports be true, the new department produces spiegelized steel, for the manufacture of all-steel rails. But the old department is still,' as from the beginning, devoted to the production by the direct method of steel for steel-headed rails. The most remarkable fact connected with this direct steel is the ease with which it welds to the iron' of the rail-packets, although no borax or other fluxing agent is used to facilitate the welding. It is very rarely that an exception occurs, and an ingot or a charge is discarded by the rail-mill. The mixture of pig-iron used for the production of this steel is melted in cupolas of very interesting construction (not to be de

Jan 1, 1874

By David J. Mack, T. V. Philip

The effects on the Cu-A1 eutectoid transformation of the addition of a third element from the second long period and from Group IIB of the periodic table, were studied by isothermal transfomation techniques. The valency of the third element shows the most pronounced effect on the eutectoid decomposition. With some exceptions, the atomic size factor of the third element shows some consistent effects on pearlite nucleation and growth. The atomic concentration or the electronegative valency of the third element shows wo consistent effect on the eutectoid decomposition. Addition of the third element helps spheroidization of pearlite. SINCE the pioneering work of Davenport and Bainl on the eutectoid decomposition in steel by the isothermal transformation technique, an enormous amount of data has been accumulated on the eutectoid transformation characteristics of commercial steels. While the eutectoid reaction in steel is of tremendous industrial importance, it appears to be quite unique among the eutectoid reactions. Though the metal-lographic structures developed in the Fe-C and Cu-A1 eutectoids are similar, it is now evident that the two eutectoid reactions are quite dissimilar. The eutectoid decomposition in the Cu-A1 system is more complicated partly due to the appearance of transitional phases in addition to the equilibrium phases. * The first isothermal studies of aluminum bronzes were made by Smith and Lindlief2 and later by Mack,3 Klier, and Grymko,4 and recently Hayne 5,6 A few other systems, structurally analogous to the above, have been studied by the same technique.7-10 Kasberg and Mack1' studied the effects of iron on the transformation of commercial aluminum bronze. The effects of manganese and nickel on this aluminum bronze and those of iron, manganese, and nickel on the binary Cu-A1 eutectoid have been recently studied.12 The object of the present investigation was to study, by isothermal transformation techniques, the effects (with respect to the fundamental factors of alloy formation) of the addition of a third element on the transformation of a Cu-Al eutectoid alloy, 11.8 pct Al. The third elements chosen for the purpose were silver, cadmium, indium, tin, and antimony from the second long period, and beryllium, zinc, and cadmium from group 11B of the periodic table. They were added in nominal amounts of 0.5, 1.0, and 2.5 pct by weight to a eutectoid Cu-A1 alloy. These third elements were expected to show the effects of electron valency, atomic size factor, and electronegative valency effects on the binary eutectoid transformation. PFLEPARATION OF ALLOYS AND PROCEDURE All alloys were made as 400-g heats by induction melting in a graphite crucible with a graphite lid. The molten alloy with a layer of graphite powder on top was stirred at regular intervals by a graphite rod. When the melt was judged to have acquired sufficient superheat, a pinch of common salt was sprinkled on top and any crust scraped off to one side. It was then chill cast into a 5/8 in. rod. The alloys with silver were prepared by remelt-ing the high-purity Cu-A1 eutectoid alloy used by Mack3 with high-purity silver (99.99 pct pure from Hardy and Harmon, Inc.). In the preparation of all the other alloys, polished electrolytic copper shot (from Belmont Smelting and Refining Co.) and high-purity aluminum (99.99 pct pure from Aluminum Co. of America) were used.

Jan 1, 1962

By Hans S. Carlsson

Like most industrial processes, nuclear power production creates wastes, which have to be handled and ultimately disposed of in a safe manner. Some of the wastes contain very long-lived radioactive substances and have to be isolated for very long periods of time before they have decayed to harmless levels. Sweden, like many other countries with similar geology, intends to use crystalline rock for isolating the high-level nuclear waste from the biosphere. The suitability of a rock mass for a repository needs to be investigated extensively. Apart from the political and practical considerations for a site selection, a detailed study has to be performed in terms of geology, hydrogeology, geophysics, geochemistry and rock mechanics. The responsibility of the site selection studies in Sweden is entrusted to the Swedish Nuclear Fuel Supply Company, Division KBS (SKBF/KBS) . The paper gives a brief presentation of the "Standard Program" for the studies that will be carried out during 1980-1990. Modifications of the program are justified on the basis of gained experience or specific circumstances for each site. The program is compiled by the Geological Survey of Sweden (SGU) in cooperation with KBS.

Jan 1, 1982

By J. P. Dunlop

The fact is not.ablc though probably little known that thc Unitcd Statcls is the only nation obtaining and distributing through its Govcrn-ment burcaus any data pertaining to waste metals and drosses. Some foreign goverrlnlents do issuc reports relating to rnine or smelter production of prirrlar~ metals, but none gives in scope and detail t'he information published now by the U. S. Bureau of Mines and formerly by the U. S. Geological Survey; and this is despite the fact that the funds annually allotted for those purposes are insignificant in comparison with allotments for the preparation of data relating to other industries of like importance. The earliest data on the production of metals from secondary sources in the United States were contained in a press bulletin issued by the U. S. Geological Survey on Jan. 4, 1909. The information published was that for thc year 1907 obtained ant1 compiled by C. E. Siebenthal, who was one of the first to visualize the growing importance of the scrap-letal indust,ry. Thc Nationd Conscrvation Commission had emphasized its opinion that the known domestic supply of certain kinds of the morc important irietals was being rapidly marketed and that while there was no immediate cause for concern it was best to conserve such resources. Not only had there been a lanlentable lack of any data regarding the quantity of scrap inetals available or used but also gross carelessness and indifference in the segregation, collection, and effective use of scrap material. Siebenthal realized that even approximately correct statistics of recoveries from the more important base-metal scrap and drosses wcrc nearly as essential t,o both producers and consumers as the stat'istics of the output of primary metals. There were not then nor are there now sufficient funds for complete collection of data, nor was it considered the province of the Geological Survey t'o do more than determine approximately the recovery of secondary metals for use in supplementing those given for the primary metals. Undoubtedly the first bulletins issued did not give the full output, for it takes time to establish contacts for an inquiry covering so

By R. G. Ward, John Henderson

It has been shown1 that the observed density1-' of liquid iron silicates in contact with solid iron depends upon whether nitrogen or argon is used to protect the experimental system from oxidation. These densities have been measured by the maximum bubble-pressure method, in five different labora-

Jan 1, 1965

Key elements of open-pit design fixing the ultimate pit limits are stripping ratio, pit slope angle, and grade cutoff. Results of exploratory and development drilling should be reduced to horizontal sections corresponding to level spacing. It is advisable to interpolate the actual drillhole values to a uniformly spaced 50-ft grid system. Vertical sections can be and are used to approximate the fixing of pit limits, but horizontal sections must be used to optimize a pit design. To develop a pit design requires the establishment of the break-even stripping ratio. This ratio is applied only at the surface of the final pit and must not be confused with the over-all ratio, which is always less; otherwise there would be no profit in the operation. The break-even stripping ratio is determined by the formula: [ ]

Jan 10, 1967

By Carle Hayward

THE effect of copper on steel has been studied by numerous investigators. Before modern testing methods had been developed, blacksmiths noted red shortness in iron, the cause for which was ascribed to the presence of copper. Numerous papers have been published on the corrosion of steels containing various amounts of copper, and a few writers have discussed the effect of copper on the mechanical properties of steel. The purpose of the investigation described in the following paper was to obtain additional data on the mechanical properties of medium-carbon steel containing small quantities of copper. Among those who have published results of mechanical tests on copper steels are Ball,1 who states that copper increases the tensile strength and 'hardness but lowers the elongation. Stead2 states that copper steels closely resemble nickel steels containing equivalent percentages of nickel,, as regards tensile strength, resistance to shock, corrosion and hardness. Wigham 5 found that copper in small amounts had no injurious effect on steel. Breuil4 found that with 1 per cent. carbon, copper lessened the brittleness of steel and in low-carbon steel it increased the tensile strength and lowered the ductility slightly. H. H. Campbell 5 states that copper up to 0.25 per cent. slightly raises the elastic limit, elongation and reduction of area.

Jan 1, 1918

By D. J. Mack, J. A. Mullendore

MUCH work has been reported in the literature on the separation of individual phases in steels, particularly carbides, for the purpose of structural and chemical analysis. The methods usually involve separation of the particles from the matrix by chemical or electrochemical methods. Another .group of alloys ideally suited for selective removal of one phase is the commercial aluminum bronzes. Al-

Jan 1, 1959

By J. L. Gregg

A study of copper-base and silver-base alloys was made with the object of finding, if possible, useful alloys subject to dispersion hardening. These studies led to the discovery of several alloys showing considerable dispersion hardening, the most important of which, the alloys of copper with iron, nickel, cobalt and chromium silicides, have since been very ably reported by M. G. Corson.l This paper is offered as a few notes covering alloys other than those described by Corson and some further data on the silicide alloys. Copper Alloys For the purpose of making a rapid survey of copper alloys that might show useful dispersion-hardening phenomena, various alloys were prepared containing 3 per cent. of additional elements added in such proportion that possible compounds could be formed without an excess of either added element. These alloys in the form of rolled or forged pieces were quenched in water from a temperature of 871" C. (1800" F.) and subsequently aged at various lower temperatures for l-hr. periods. The comparison of the Rockwell hardness of the quenched alloys with the maximum hardness of the alloys after aging was used as a measure of the dispersion hardening. Table 1 shows the Rockwell "E" hardness 1/8-in. ball, 100-kg. load) of the quenched alloys, together with the maximum hardness resulting from aging. The reheating temperature given in this table is the aging temperature at which maximum hardness resulted from a l-hr. sojourn. From this table it may be observed that only the silicide alloys showed significant dispersion hardening. Of these, the only one not described by Corson is the Cu-Be-Si alloy. This alloy contained 1.35 per cent. beryllium and 1.78 per cent. silicon, which is approximately equivalent to 3 per cent. Be2Si. It had a yellow color and scaled much less than the other silicide alloys upon heating. It could be worked easily either hot or cold but hardened very rapidly on cold working. The annealed alloy upon drawing from a diameter

Jan 1, 1929

By J. L. Gregg

A study of copper-base and silver-base alloys was made with the object of finding, if possible, useful alloys subject to dispersion hardening. These studies led to the discovery of several alloys showing considerable dispersion hardening, the most important of which, the alloys of copper with iron, nickel, cobalt and chromium silicides, have since been very ably reported by M. G. Corson.l This paper is offered as a few notes covering alloys other than those described by Corson and some further data on the silicide alloys. Copper Alloys For the purpose of making a rapid survey of copper alloys that might show useful dispersion-hardening phenomena, various alloys were prepared containing 3 per cent. of additional elements added in such proportion that possible compounds could be formed without an excess of either added element. These alloys in the form of rolled or forged pieces were quenched in water from a temperature of 871" C. (1800" F.) and subsequently aged at various lower temperatures for l-hr. periods. The comparison of the Rockwell hardness of the quenched alloys with the maximum hardness of the alloys after aging was used as a measure of the dispersion hardening. Table 1 shows the Rockwell "E" hardness 1/8-in. ball, 100-kg. load) of the quenched alloys, together with the maximum hardness resulting from aging. The reheating temperature given in this table is the aging temperature at which maximum hardness resulted from a l-hr. sojourn. From this table it may be observed that only the silicide alloys showed significant dispersion hardening. Of these, the only one not described by Corson is the Cu-Be-Si alloy. This alloy contained 1.35 per cent. beryllium and 1.78 per cent. silicon, which is approximately equivalent to 3 per cent. Be2Si. It had a yellow color and scaled much less than the other silicide alloys upon heating. It could be worked easily either hot or cold but hardened very rapidly on cold working. The annealed alloy upon drawing from a diameter

Jan 1, 1929

By L. P. Bayvel

The method of spectral transparency was investigated. A device for measuring particle sizes based on this method was developed, tested and applied. The device affords measurements of particle size distribution in the range from 0.1 to 4 µm. It proved possible to measure sizes not only of spherical particles but also of non- spherical ones. The spectral range in which it is necessary to determine transparency for particle size measurements was found.

Jan 1, 1980

By R. A. Vandermeer, C. J. McHargue

The (001) fiber-texture component, found in aluminum rods extruded at subzero temperatures, consists of particles of various sizes having extremely irregular shapes dispersed in a nonuniform way throughout a matrix of the (111) orientation. Apparently the (001) texture component is not a result of recrystallization but rather is due to the presence of reimanents of the original grains which fragmented from the main body of material as it reoriented towards the (111) orientation during the extrusion process. Both X-ray line-broadening measurements and electron-microscopic observatwns indicate that, after extrusion, regions having (001) orientations are in a state of relatively less strain and distortion than (111) regions, suggesting that the former have undergone less plastic deformation. A (001) fiber-texture component is also found after complete recrystallization of extruded specimens. Approximately one third of the recrys-stallized volume has this orientation. The (001) fragments, formed during the extrusion process, act as nuclei for recrystallization; i.e., the pain boundaries separating these fragments from the matrix are capable of migrating during annealing. Electron-transmission microscopic observations and X-ray line-broadening measurements indicate that (001) regions recover at a much more rapid rate than (111) regions at annealing temperatures up to 187°C. DURING the extrusion of a rod or the drawing of a wire the individual grains comprising the piece tend to reorient towards a preferred orientation (texture) which is of the fiber type where a particular crys-tallographic direction, (uvw), in each crystallite tends to be aligned parallel to the longitudinal axis

Jan 1, 1964

By William P. Blake

The salt-beds at Salton, on the line of the Southern Pacific railway, in San Diego county, California, have been successfully worked for many years by the corporation known as the East Liverpool Salt Co., and the salt has been largely used upon the Pacific coast generally and in the interior. But the industry has lately been destroyed by the overflow from the Colorado river. The salt is dissolved, and the waves of the Salton sea now roll 50 ft. above the site of this once thriving and growing business. The salt-bed was evidently the residual accumulation from the waters of an ancient lake, which I have named Cahuilla, from the name by which a large part of the valley—the home of the Cahuilla tribe of Indians—is known. The deposit covered a comparatively small area in the lowest part of the valley, 280 R. or more below the sea-level. This depressed area is now generally known as the Colorado desert, but has a soil of wonderful fertility wherever water can be had on its surface. The deserted beaches, and the water-lines, only a few feet above tide-level, upon the rocks of the bordering mountains, as well as a great abundance of shells in the soil, all bear decisive testimony to the former occupation of the valley by water. The depression is topographically the northern end of the Gulf of California, from which it is now separated by the delta of the Colorado river, extending practically from the mouth of the Gila river across the valley to the coast mountains on the

Jan 1, 1908

By Kenneth L. Zonge

Recently, extensive field use has been made of a digital minicomputer incorporated into a modified geophysical prospecting method. This is a generalized induced polarization (IP) system called complex resistivity (CR) and has been successfully used in sulfide mineral exploration. The ease of use, portability and cost effectiveness of this computer-controlled method has provided a viable exploration tool based on a complex data acquisition system. Without the computer, this method would still be relegated to tedious laboratory measurements and theoretical studies.

Jan 1, 1976

By T. C. Craig

During the year, there were 570 oil wells completed for a total daily initial production of 365,352 bbl. The daily oil potential of the field, effective Jan. 1, 1935, as established by the Texas Railroad Commission, was 306,102 bbl. with a daily allowable of 58,800 bbl., whereas, on Dec. 31, 1935, the potential was 587,376 bbl. with a daily allowable of 57,800 bbl. Because of the limited market demand, the allowable decreased although the potential increased. In August, the five-day test for determining the potential production of a well was replaced by a 24-hr. test. The reason for this change was that some of the oil-pur-chasing companies contended that too much oil in excess of the limited market demand was produced during the five-day tests. Dry Gas.—During July, the Texas Railroad Commission supervised the first complete and accurate field-wide test of open flows that has been made in this area. The total open flow as determined at that time was 16,426,085,000 cu. ft, There were 79 gas wells drilled in '935, with a combined open flow of 2,408,000,000 cu. ft. and 50 depleted oil wells were plugged back for gas with a total open flow of 529,800,000 cu. ft. The total new gas production for the year was, therefore, 2,937,800,000 cu. ft. The 17 natural-gas pipe lines drawing on the Panhandle supply of fuel gas withdrew a daily average of 420,497,507 cu. ft., or a total of 153,481,-590,000 cu. ft. for the year. The 44th Texas Legislature passed a statute known as House Bill No. 266, which was designed to prohibit waste and protect correlative rights by compelling the ratable production of gas. The part of the law relative to withdrawal of sweet gas became effective Aug. 1, 1935, and the part referring to withdrawal of sour gas became effective Oct. 1, 1935. Three of the major pipe line companies attacked the validity of the ratable production feature of the new law and a preliminary injunction was granted by the Federal District Court. The final hearing on the incrits of the case is scheduled for the early part of January. Natural Gasoline.—Forty of the 42 natural-gasoline extraction plants in the Panhandle operated throughout the year. One plant discontinued

Jan 1, 1936