Search Documents

By Ray W. Carpenter, Ralph Hultgren, Raymond L. Orr

Heats of formation of Au-Zn alloys of compositions Au3Zn and AuZn were rneasured at several temperatures by liquid tin solution calorimetry. The data for Au3Zn show that much smaller heat and entropy effects are associated with the a2- a1 transformation than for the a1 - a transformation. This result is consistent with reported X-ray diffraction studies which indicate that the a1 and (a2 phases have ordered structures which only slightly differ, whereas the a phase is disordered. The heat of formation of AuZn(ß') does not change significantly between 322o and 8000 K, confirming that the ß' alloy remains highly ordered to high temperatures. Not many measurements have been made of the energies of order-disorder transformations in alloy phases. In many cases these energies may be conveniently determined by measuring heats of formation as a function of temperature. Many alloy phases approximately obey Kopp's law of additivity of heat capacities; as a consequence their heats of formation do not change with temperature. In ordered alloys, however, a decrease in degree of order with increasing temperature will contribute an endothermic component to the heat of formation. Thus, for ordered phases where other anomalous contributions to heat capacity in the alloy or its pure components are absent, a measured change in the heat of formation may be attributed to the energy of disordering. A portion of the Au-Zn phase diagram1" is shown in Fig. 1. The composition AuZn(ß') has a well-ordered superlattice structure of the CsCl type at room temperature. The alloy is considered to remain ordered to its melting point,1 although, from X-ray diffraction data and electromotive force measurements of zinc activities, Terpilowski3 concluded that considerable disordering began at -673°K. The Au3Zn composition is a disordered fee solid solution (a) at high temperatures. Between 693o and 543oK, the ailoy orders to form the a1 phase, having a structure based on the L12(AuCu3) type, but with a regular distribution of ordering faults in the c direction, making it tetragonal. Below 543oK, the alloy orders further by means of slight atomic shifts, without diffusion, yielding a complex long-period orthorhom-bic superlattice structure, a2.4-7 Heats of formation of Au3Zn(a2) and AuZn(ß') were measured at 363°K by Biltz et al.8 by aqueous solution calorimetry. Heat capacities of several alloys between 14.9 and 38.4 at. pet Zn in the range from 373" to 723°K were measured by Iwasaki ef al.6 Stoichiometric Au3Zn, however, was not included in the alloys measured, the nearest composition being 26.1 at, pet Zn. Also, the heating rate used for the measurements, 2 deg per min, may not have permitted equilibrium to be reached in the neighborhood of the transformations. Heat contents of solid and liquid AuZn were measured between 488o and 1138°K by Kubaschewski.9 It was decided to determine the ordering energies of Au3Zn and to check on the possible disordering of AuZn by measuring the heats of formation of these alloys at several temperatures. The present paper reports measurements by liquid tin solution calorimetry of the heats of formation of the three phases of Au3Zn at temperatures within their regions of stability, and of AuZn at a low (322°K) and a high (800°K) temperature. EXPERIMENTAL Alloy Preparation and X-Ray Examination. Ten-gram ingots of Au3Zn and AuZn were prepared by melting weighed amounts of gold (99.95 pct Au) and zinc (99.99 pet Zn) together in sealed evacuated Vycor tubes at 1060°K, followed by rapid quenching. The resulting ingots were homogenized at 900°K for 10 days. The Au3Zn alloy lost no weight in preparation, the loss from the AuZn alloy was enough to introduce an uncertainty of only 0.1 at. pet in its composition. Filings for X-ray examination were taken from various parts of each ingot and strain-annealed at 723°K for 20 min in vacuo. The Au3Zn filings were quenched rapidly to retain the disordered phase. Diffraction patterns were determined with an X-ray dif-fractometer using copper Ka radiation.

Jan 1, 1968

By Verne C. Fryklund, S. Warren Hobbs

The Coeur d'Alene district in the panhandle of Idaho is one of the major lead-zinc-silver producing areas in the world. The value of recorded production to date has exceeded $2 billion. Country rock comprises six formations of the fine-grained, highly siliceous, and slightly metamorphosed Precambrian Belt Series. Small stocks of monzonitic rocks and several varieties of dikes intrude the sediments. The district is at the intersection of a north trending major anticlinal uplift and the west northwest-trending Lewis and Clark line of which the Osburn fault is the dominant feature. The district structure is complicated and comprises folds, some of which are overturned, and a complex of faults of diverse ages and directions of movement. Late Cretaceous stocks but are also probably Cretaceous in age. The productive veins are localized within a series of 12 subparallel, straight mineral belts that trend approximately N65°W and that appear to be controlled by deep fractures in the basement rocks. The mineral belts are in two groups, separated by 15 miles of post-mineralization movement on the Osburn fault. Veins and ore shoots are variously disposed within each mineral belt. Many crop out at the surface, but others apex several thousand feet beneath it. Local controls that influence the position of ore shoots within the mineral belts include the brittle character of host rock attitude of bedding relative to the mineralized fracture, and the amount and direction of movement on faults. Depth appears to have had little effect on the occurrence or type of ore. Ore occurs in a series of steeply dipping replacement veins of relatively simple mineralogy. Six periods of mineralization, ranging from Precambrian to Tertiary in age, are recognized. The productive galena sphalerite-bearing and tetrahedrite-bearing veins-of the main period of mineralization-are younger than the

Jan 1, 1968

The high-grade orebody at Miami was mined successively by top-slicing, shrinkage, stoping and under caving. The method described in this paper was developed to enable the low-grade orebody (36,000,000 tons assaying 1.06 per cent copper) to be mined at a low cost without further dilution of the grade. The method is clearly described and illustrated by drawings and photographs, and the original paper should be consulted as it is impracticable to abstract it, beyond noting that the mining cost is just under 40 cents per ton and the average grade of ore now being produced yields less copper than the mill tailing of 1915, the tons mined per day having increased from 4000 to 18,000 in the same period. Vertical and Incline Shaft Sinking at North Star Mine By Arthur B. Foote, Grass Valley, Calif. (Tech. Pub. No. 324: Class A. Metal Mining, No. 36) THE main shaft of the North Star mine is an inclined one following the main vein at an average dip of 26 deg., a vertical shaft intersects it at the 4000-ft. (incline) level, the incline continuing to the 6300-ft. level. At this point the vein was found to give out and a new vein, called the No. 1, was found to dip in exactly the opposite direction.

Jan 1, 1930

Alexander Forsyth, Southport, Me. (communication to the Secretary): In Mr. Irving's able and interesting paper he describes minutely the appearance of the wolframite and its association with the refractory siliceous gold-ore. He also describes this gold-ore, but fails to mention the important pockets of metallic gold found in the Lead City occurrence of it. I use the term " metallic " in preference to the more usual " free," for it has been found that this gold is not easily amalgamated. Metallic gold is comparatively rare in the refractory siliceous gold-ores of the Black Hills; hence its occurrence in considerable amounts in the Lead City wolframite district deserves notice. I possess a beautiful specimen from the Harrison mine. It is a lump of drusy, granular ore, about 6 in. in diameter. The gold .is " shot" through it in large and small pin-heads; and in two specially oxidized areas, each about 11/2 in. in diameter, it is peppered full. The famous " Grantz strike," made in the Lead City wolframite locality, produced many beautiful gold specimens. This district affords an excellent example of the repeated discovery of new mineral values upon old ground. By reason of its proximity to the Homestake vein, this wolframite deposit was inevitably traversed many times by experienced geologists, mineralogists and mining engineers, who evidently must have thrown aside, with no thought of wolframite, the lumps of " black iron " lying about. I have the admission of an able geologist that, six months before the wolframite was discovered, he visited some of the very mines where it occurred, and passed it by as magnetic iron-ore. At the time of the discovery, the mineral was scattered over the gold-mine dumps in no small quantities, having been culled as worthless out of the gold-ore. It remained for

Jan 1, 1902

By E. A. Peretti

BEFORE embarking on a detailed investigation of the system indium-antimony-bismuth, experiments were carried out to determine the existence of quasi-binary sections. The bordering binary systems are known1 and show the occurrence of three intermetallic binary species corresponding closely to InSb, InBi and In2Bi. Attention was focused on the low-indium end of the ternary diagram where the possible quasi-binary sections, excluding ternary compound formation, would involve the pairs: InSb-Bi, InBi-Sb and InSb-InBi. The latter pair revealed itself as a true quasi-binary, so it was investigated fully by thermal analysis, x-ray and microscopic examinations. All compositions were made by proper combination of three elements involved. The indium had a guaranteed purity of 99.97 pet; the antimony contained 99.99 pet Sb, and the bismuth had a purity of 99.99 pet. Alloys were made by melting together antimony, bismuth and indium in evacuated, sealed pyrex-glass tubes at a temperature of 600°C with vigorous agitation. The melts, weighing about 80 grams, were allowed to freeze in the sealed tubes and finally were transferred to glass tubes for the taking of cooling and heating curves. A protective atmosphere of helium was used, and the melts were stirred mechanically while cooling at rates of from 0.5 to 3°C per min. Temperatures were measured with a calibrated chromel-alumel thermocouple and were recorded graphically on a Minneapolis-Honeywell extended-range recorder working in conjunction with a Leeds and Northrup type K-2 potentiometer. Conventional polishing techniques gave satisfactory results in preparing specimens for microscopic examination. Etching was carried out with Vilella's reagent or aqueous mixtures of chromic oxide with either nitric acid or sulfuric acid plus dichromate. Conclusions deduced from the thermal analysis and microscopic examinations were confirmed by X-ray photograms using Co-K alpha radiation. The phase diagram is shown in Fig. 1. The liqui-dus consists of an uninterrupted line running from the freezing point of InSb (525°C) to a eutectic point experimentally indistinguishable from the freezing point of InBi (110°C). X-ray patterns of the InSb show a slight expansion of the lattice with the addition of InBi, and microscopic work indicated the solid solubility of InBi in InSb to be less than 0.5 pet at room temperature. Acknowledgment We wish to thank the Indium Corporation of America for the loan of the indium used in this investigation. References 1 E. A. Peretti and S. C. Carapella, Jr.: Trans. ASM., 1949, vol. 41, P. 947. T. S. Liu and E. A. Peretti: Trans. ASM, 1952, vol. 44, p. 539. Metals Reference Book, vol. 1, 2nd ed., AIME, p. 345.

Jan 1, 1959

By Walter E. Hopper

The Caddo oil-field, shown in Fig. 1, is located in Caddo parish, northwestern Louisiana. The known producing territory of oil is covered by townships 19 N, 20 N, 21 N, 22 N, and ranges 15 and 16 W., shown in Fig. 2. The center of the field may be taken as Oil City, 24 miles north of Shreveport, on the Kansas City Southern railway. Shreveport is the second largest city in the State, and is the connecting point of five railroad-lines. Drilling at the present time, however, is going on all over northern Louisiana, especially in Caddo and the neighboring parishes. During the winter of 1908-09 I spent 'four months in the Caddo field, under the direction of the Louisiana Geological Survey and the U. S. Geological Survey. II. History and Development. Natural gas escaping at the surface is found at numerous places in northwestern Louisiana. At Shreveport, the plant of the Shreveport Ice & Refrigerating Co. has been lighted by natural gas for 20 years. The well was drilled for water, but was abandoned on account of the gas. A test well, put down in 1905 near the western limits of Shreveport, was driven to 1,650 ft., and encountered indications of gas and oil at various depths, but did not succeed in finding enough to be profitable. Attention was first attracted to the Caddo field in 1895 by indications in water-wells from 40 to 60 ft. deep, in which the pressure of natural gas was noticeable. This indication of gas in a shallow well led to the drilling of the first well in the Caddo field, the old Savage Brothers & Morricell, or the Caddo Lake Oil and Pipe Line No. 1. The rig for this well was erected in May, 1904, and drilling began in June, 1904. The well was bailed Mar. 23, 1905, with a small amount of oil. It was deepened July, 1905, and converted into a "gasser" Jan. 3, 1906. It was abandoned January, 1907. In consequence of the finding of oil in the Savage well, drilling-operations were pushed with energy; and in April, 1905,

Jan 1, 1912

Charles H. Morgan, Worcester, Mass. (communication to the Secretary): In connection with Mr. Douglas's mention of the continuous charcoal kiln used at Kopparberg, some further data concerning this important invention may be of interest. Before giving these, however, I will say a word or two concerning other features of Swedish practice. In 1894 I spent two days at Soderfers with Mr. Tom Bergendal, the manager of the works, and was specially interested in the gas-producers and wood-drying kiln, illustrated in the paper contributed to our Transactions by Mr. Odelstjerna in that year.* The wood-drying kiln is, however, quite different in design and construction from Ljungberg's charcoal kiln. In the summer of 1894 it was discovered that by placing the gas-producer as close as possible to the open-hearth furnace, and working the producer hot, ordinary weather-dried wood, still containing a considerable percentage of moisture, could be used to advantage in the melting-furnace. Hence, the dryingkiln was needed for wet wood only. One of the iron-works of the Udeholm Go. was the first to adopt the Lundin saw-dust gas-producer and condenser, enabling them to make gas from saw-dust containing 45 per cent. of moisture, and convey the gas from the condenser through wooden pipes to the Siemens steel-melting furnace.† This sawdust gas gave very satisfactory results in iron-works; but the proprietors experienced much trouble by reason of the pollution of rivers by the tar-water from the condenser. On my visit, in 1894,I found that the Udeholm Co. had put in for their steel-melting furnaces the same wood-gas producers

Jan 1, 1899

By MARSHALL D. DRAPER

THERE are said to be about 150 operating companies in Kotchiu, most of these being small, corresponding in degree to lessees in western mines in the United States. Of the total number there are probably forty large companies having their own smelting plants equipped with one or two furnaces, slag crushing plant and other accessory equipment. A few plants, not more than ten, do custom smelting. There are in all about fifty smelting plants in Kotchiu. With little variation, the equipment and methods are the same. The plant usually consists of two furnaces, one being in operation while the other is being relined 01- re- paired. An adjoining house contains one or more of the large buffalo-drawn Chilean mills for crushing slag. A few houses for the working coolies, with more pretentious ones for the owners, complete the establishment, the whole being surrounded by a compound wall 8 ft. high.

Jan 1, 1931

By C. Kremer Bain

DURING the past several years of diamond drilling in Washington County, Mo., the St. Joseph Lead Co. has discovered a concentration of commercial lead-zinc ore at four different points within an area of 36 square miles. The largest and to date the most promising group of these orebodies is located in the Indian Creek area. It was considered to be of sufficient value to warrant development.

Jan 9, 1953

By J. C. Trantham, J. W. Marx

From 1955 to 1958 the Phillips Petroleum Co. conducted a series of small scale counterflow combustion field tests in a tar sand about 60-ft deep and 6 to 12-ft thick near Bellamy, Mo. A total of seven different well patterns, including conventional five-spots and seven-spots plus a 15-well line drive pattern and a 10-well radial pattern, were employed. Electric heaters, gas burners and wellbore fuel packs were tested as counterflow ignition devices. Direct drive ignition followed by reversal to counterflow operation was not possible in this case because of formation plugging by the semi-solid tar during the direct drive phase. Sustained counterflow burning was achieved with wellbore fuel packs under conirolled conditions which permitted close correlation of fire front velocity, air velocity, air-oil ratios and yields for a wide variation in process parameters. The tar in place was about 10' APl with a reservoir viscosity greater than 500,000 cp. The composite oil prodlcct was 26' API with a viscosity in the range of 5 to 15 cp. Vertical sweep efficiency in the line drive pattern was essentially 100 per cent, with no evidence of gravity segregation. Original tar in place ranged between 800 and 1,000 bbllacre-ft, specific rock permeability averaged about 800 md before burning and effective air pemeability with residual oil and water in place (at the time of ignition) averaged 250 md. The volume of oil recovered during stabilized line drive counterflow burning represented about 67 per cent of the volume of tar originally in place in the burned out zones. A minimum was found when air-oil ratios were plotted against formation air velocities, and a limiting air velocity existed below which the counterflow fire front reversed and burned back over its own trajectory, using the residual coke left behind. INTRODUCTION Early in 1955 the Phillips Petroleum Co. began preparations to field test counterflow underground combustion as a method for producing oil from high viscosity hydrocarbon deposits, such as bituminous (tar) sands. At that time all published information on the use of underground burning io increase oil recovery was based on the direct drive process, in which the fire front moved through the formatim in the same direction as the injected air stream. Such direct burning is not applicable to many heavy oil sands or to most tar sands because the heat-thinned native hydrocarbon congeals in the cold rock ahead of the fire front forming a gas permeability block which smothers the combustion. Laboratory experiments first demonstrated that this permeability blocking would not occur if the fire front and the air stream moved in opposite directions. In this counterflow (reverse) burning process the heated heavy oil or tar is driven back through the combustion zone. Here thermal cracking produces relatively light hydrocarbon products which pass through the heated rock behind the fire front (largely in the vapor phase) and are incapable of causing a gas permeability block.' Exploratory wring revealed that consolidated bituminous sandstones with a combination of tar saturation, permeability, thickness and depth favorable for experimental field testing existed at several points in western Missouri. By the fall of 1955, a test site for determining technical feasibility of the counterflow process under field conditions had been selected near Bellamy, Vernon County, Mo. — about fifty miles north of Joplin. The pay zone was too thin and too shallow to constitute a commercial prospect, but these same factors permitted controlled experimental operation with a small compressor installation and with a large number of monitor wells. These were needed for adequate observation of the underground phenomena at reasonable cost. RESERVOIR CHARACTERISTICS The reservoir chosen for the experimental field tests was a 124 thick section of tar sand extending from 49 to 61 ft subsurface, with shale and siltstone laminations sealing the top and bottom. This section was part of a larger 30-ft thick tar sand deposit which extended both above and below the test zone. Core analyses showed that the 12-ft sand was effectively subdivided into two approximately equal sections, with the lower zone being consistently more permeable than the upper zone. The most significant laboratory core data are summarized in Table 1. The line drive test which is the principal subject of this report utilized only the lower 6-ft thick zone, with the upper zone regarded as part of the 55-ft overburden. WELL PATTERNS The over-all field test program involved a total of seven different well patterns, including conventional five-spots and seven-spots plus a 15-well line drive pattern and a 10-well radial pattern. In some of the tests the full 12-ft zone was employed; in other cases only the more perme-

Jan 1, 1967

By G. M. Ault, G. C. Deutsch

The paper reviews the efforts made to utilize powder metallurgy to solve problems encountered when using alloys at high temperatures. The following subjects are discussed: comparison of wrought and sintered super alloys, sintered aluminum powder, porous materials for transpiration cooling, molybdenum, and cermets. TODAY, powder-metallurgy techniques are be-JL coming increasingly important, producing materials which at the present time cannot be made by any other method. Among these materials are high melting-point metals such as tantalum and tungsten, porous metals for filters and lubricant-containing bearings, electrical contacts and electrodes (i.e., tungsten-copper), cutting tools of the cemented carbides, and magnet alloys. In addition, the powder-metallurgy industry has grown because, through the application of its methods, shaped parts, such as gears, can be produced at tremendous rates with a low scrap loss in comparison with manufacture by casting or forging and machining. In the past few years, by utilizing powder metallurgy, several approaches to the problem of high temperature materials have been investigated. In this paper the authors will review some of the studies on application of materials having properties above 1350°F. Since their experience lies in the aeronautical field, possible uses of powder-metallurgy techniques in the production of aircraft en- gines will be emphasized. A large portion of the work is classified, but such a restriction has not eliminated any field from discussion, although limiting the amount of detail it is possible to present. The development of high temperature alloys from powders and porous metals for cooling will be discussed as well as research done on molybdenum and molybdenum alloys, cermets, and intermetallics. Some studies on the utilization of cermets will be considered along with special problems that have been revealed through these investigations. Special interest in certain factors of sintered aluminum powder (SAP) makes it desirable to discuss this material although its use temperature is below the 1350°F limitation set for this paper. High Temperature Alloys from Powders In general, components made from powders for room-temperature application have been investigated with the primary purpose of taking advantage of the high production rates and economies made possible by powder metallurgy. From the standpoint of properties, the ojective of the powder metallurgist has been to obtain a product comparable to the cast or wrought product that is to be replaced. Comparisons of the properties of alloys made by powder-metallurgy methods with those of similar compositions made by casting and forging are reported in the literature.12 In many cases equivalent

Jan 1, 1955

By J. M. Cases

Study of the normal interaction between flotation collectors and the silicates through measurement of the electrokinetic potential carried out by the streaming potential and flotation recovery methods indicates that the interaction is wholly 07 partly of electrostatic origin. In some cases, it partly consists of the chemical affinity of the polar head of the collector for the active surface sites. Reagents composed of a polar head and a paraffinic chain and forming micelles in solution were used as flotation collectors. They are sodium dodecylsulfate (anionic collector) and dode-cylammonium chloride (cationic collector). The adsorption isotherms on biotite of alkylamine chloride having 10 to 18 carbon atoms in their chain all show a sharp change in slope relevant to the condensation of alkylammonium ions into bidimensional phase.1-1 Condensation is possible because of the relative homogeneity of the adsorbing surface and of the very strong lateral binding forces through Van der Waals type bonds in the adsorption layer. The different isotherms are seen to coincide when, instead of the equilibrium concentration, the under-saturation ?µ = kT In C/C, is plotted in abscissa, C representing the concentration of the solution with which the adsorbed layer is in equilibrium and C, the saturation concentration of micelles in solution or. critical micellar concentration. More particularly, the undersaturation ?,u1*, corresponding to a surface coverage 6 of 0.5, is equal to Since silicates immersed in aqueous solutions show a surface charge which is a function of pH, it is of primary importance to study the influence of this parameter on the adsorption of collector ions acting as Strong electrolytes in the pH range where they are utilized. The aim of this present paper is to determine by studying electrokinetic phenomena and recovery curves effectuated with a cationic collector and a anionic collector, the nature of the normal adsorbate-adsorbent interaction. Tables 1 and 2 sum up part of the results previously obtained'H11 for the determination of the point of zero charge of the silicate studied by the streaming potential method. Throughout the remainder of this paper, the surface charge will be considered positive for all values of pH below the point

Jan 1, 1971

By W. P. Blake

One of the most remarkable iron-ore districts of the world is found in Southern Utah, in Iron County, about 270 miles south of Salt Lake City, and 10 miles west of Cedar City. This region has long been known in a general way; but, being at present somewhat difficult of access, it has been rarely visited by 'any of our members. Professor Newberry has published somewhere a short description. Last year, by the invitation of J. R. Walker, Esq., of Salt Lake City, one of our associate members, I formed one of a party, including Professor G. W. Maynard and W. S. Keyes, to visit and inspect the region. A special car was placed at our disposal by the courtesy of Hon. John Sharp, Superintendent of the Utah Central Railway. From the present southern terminus of the road at Milford, a drive of 55 miles took us to Cedar City, about 10 miles east of the iron region. The ores outcrop in a low range of hills or mountains, and stand out in such bold relief from the general surface, and are so massive and jet black, that they may be seen for miles before they are reached. These outcrops extend in long lines over the hills, and mark very . clearly the course of the beds, conforming generally to the inclosing stratified formations, probably of Palaeozoic age. These rocks are somewhat obscure, but there are large outcrops of limestone without much alteration. This, in places, appears to be the adjoining rock, at others the wall-rocks are porphyry, and at others apparently a quartzite and a fine-grained felsite. The beds of iron-ore are from 10 to 100 feet and more in thick ness, and some of the outcrops extend unbroken continuously for 1000 feet and more. It consists chiefly of magnetite and hematite,

Jan 1, 1886

F. E. Bachman, Port Henry, N. T. (communication to the Secretary*):—In discussing Mr. o.o.Laudig's paper, the Action of Blast-Furnace Gases Upon Various Iron-Ores,' I took the ground that Mesabi-ore explosions were entirely mechanical; but more observation and later experience has caused me to

Jan 1, 1905

By Harry C. Wiess

PETROLEUM has come to be one of the most important and essential of the mineral re- sources of the nation. It is the most advantageous source of mineral fuels and of lubricants, and as such it has provided in large measure for the phenomenal development in our modern means of travel and in the facilities for transportation by land, sea, and air. Without it the remark- ably rapid industrial and social progress in our country during the past thirty years could not have occurred. In view of its important place and the fact that petroleum is irreplaceable and existent in limited quantities in nature, its conservation is essential.

Jan 1, 1939

Between July 10 and August 15, 1918, the Secretary of United Engineering Society, of Engineering Foundation, and of Engineering Council visited 17 cities which are headquarters for large numbers of engineers. His mission was to tell men in all branches of the profession about "Centralized Activities of National Engineering Societies." Stops were made at Denver, Salt Lake City, Reno, San Francisco, Sacramento, Portland, Seattle, Spokane, Anaconda, Butte, Duluth,

Jan 10, 1918

By F. Z. Schellenberg

A recent visit with the engineering students of the Western University of Pennsylvania to the Keeling coal-mine on the south side of Pittsburgh furnished interesting matter to communicate, as may be the case, however, with regard to the striking features of any of our well-arranged larger collieries; for every mine surely appears unique as a whole, though description fails to give that impression, except in particulars.

Jan 1, 1900

By Frank G. Breyer

THE .following developments in the zinc field during 1935 are listed in the order of their importance. Each will he amplified in later paragraphs. In the field o f Metallic Zinc: (1) Construction of further continuous vertical retort smelting capacity in the United States and Germany. (2) Expansion of fractional distillation capacity in the United States. (3) Great expansion in the zinc-base die-casting industry in the United States and abroad. (4) Wide acceptance of heavy galvanizing by the steel industry. (5) Construction of the first commercial wire electroplating plant for putting on heavy coats of pure zinc. (6) Firm establishment and appreciable expansion of the practice of using zinc dust as a reducing agent in the organic chemical industry.

Jan 1, 1936

By Donald H. McLaughlin

ZEST in the search for new supplies of metallic ores and petroleum is difficult to maintain with stocks of raw materials accumulating and with over- production rightly or wrongly blamed for most of our industrial troubles. Enthusiasm over new methods of prospecting has consequently diminished and exploration programs in many fields have been drastically cur- tailed. Very naturally the effects have been felt with particular keeness in highly specialized phases of the work, such as geophysical prospecting, for the feverish scramble for new areas in which to drill beneath magnetic or electrical anomalies has abated, and there is even a lull in the firing in the battle over salt domes on the Gulf Coast. It is unquestionably an unhappy time for many of the organizations dependent on this work, but in certain respects the situation may be beneficial in correcting unsound practices that .have grown up through the necessity for haste and for quick decisions. With the restriction of the field to the more competent workers by the harsh rule of survival of the fittest, a general improvement, not only in technique but in business methods, can be expected which may go far in restoring public confidence. Geophysical prospecting in the short period that it has been utilized in North America, has suffered severely both from over-popularity and from excessive abuse. The former evil now

Jan 1, 1931

By H. A. Guess

A Discussion of the Paper by Mr. H. A. Guess, read at the Atlantic City meeting, February, 1904. MR. JOSEPH P. GAZZAM, Germiston, Transvaal, So. Africa (communication to the Secretary*) :-About fourteen years ago, in southeastern Missouri, I used a method for the wet determination of lead which closely resembles the modified sulphate-chromate method described by Mr. Guess. The principal difference, however, is, that after dissolving the lead chromate in hydrochloric acid, the chromic acid is determined by means of a standard solution of ferrous sulphate. The method, which I believe is still in use in southeastern Missouri, was found to be convenient and accurate for the determination of lead in the ores and various products of the mills and furnaces in that district, but it was never used for complex ores. A number of determinations of lead in mill-tailings were made in the year 1891; a few of these results are given in Table I.

Mar 1, 1905