Search Documents

By H. A. Bedworth

ALLOYS of copper and silicon have been known for one hundred years or more but the commercial development of this type of alloy has taken place during the past few years. In 1905, Sperry1 proposed the use of copper-silicon alloys for springs and other purposes for which copper-tin bronzes were used. Some attention was given to this proposal at the time but no one succeeded in producing a practical alloy containing more than a fraction of a per cent. of silicon. The equilibrium relations of the copper-silicon system were studied first by Rudolfi2 and later by Sanfourche3 and Corson.4 The constitution of the system has also been recently investigated by Matuyama,5 and in the laboratories of the American Brass Co. by Smith.6 Some of the physical properties of the copper-silicon alloys have been investigated by Norbury7 and by Geiss and Van Liempt.8 Summarizing the results of various investigators of, the constitution of copper-silicon alloys, the solubility reaches its maximum value, 6.7 per cent. silicon, between 721° and 782° C. At 852° C. the solubility is 5.25 per cent., while at 400° C. it is only 4.1 percent. silicon. The copper-silicon alloy begins to get so hard at about 3 per cent. silicon that it is difficult to manage. It was found by Jacobs that the addition of manganese to this alloy considerably improved the working

Jan 1, 1929

By R. A. Morse, W. W. Owens, D. R. Parrish, T. M. Geffen

Laboratory studies of several factors affecting measurements of relative permeability were made using the three-section plastic-covered core technique. Results show that the core assembly, properly constructed, will perform as a single unit, and that the testing technique will, under suitable conditions of pressure gradient, gas expansion, and migration of partial water saturation, permit measurement of flow characteristics not affected by technique. Wettability equilibrium is readily established in cores exhibiting strong wetting preference to water or oil when initially saturated with water. Laboratory tests must be conducted so that saturation changes represent those that occur in the reservoir. Immediate implications of saturation history are (1:) that the possibility exists of increasing the displacement efficiency of solution gas drive reservoirs over the natural process, and (2) residual gas saturations following water flooding in gas or gas condensate reservoirs will be 15 to 50 per cent pore space rather than 1 to 11 per cent as generally believed. INTRODUCTION Solutions of petroleum reservoir problems pertaining to production performance require the use of true relative permeability characteristics. 'This relationship of fluid conductivity and saturation has been obtained by reservoir engineers in four ways, namely: 1. From past gross reservoir performance and the extrapolation of this data based on experience,1,2 2. By using published fluid flow relationships obtained in laboratory studies on general type porous materials,3, 4, 5 3. By attempting a mathematical derivation of flow behavior," using some experimentally obtained characteristics of reservoir rocks, and 4. By laboratory flow tests using representative rock samples of a reservoir. The first three methods listed above have shortcomings which make their use limited or questionable. Production characteristics of only certain processes are obtained from field data and these are not available at the beginning of a reservoir's producing life, at which time they are desirable. It is fortuitous if general fluid flow characteristics obtained experimentally have accurate application to specific field problems. Also, it is felt that at this time there is not sufficient knowledge of the flow behavior of oil, water, and gas in porous materials to enable applicable analytical description of this to be made based on other measured rock characteristics. Measurement of relative permeability in the laboratory offers the only direct method subject to adequate checking for determination of flow characteristics applicable to field problems. Primarily, this paper deals with laboratory experiments to establish the effects of several factors on the measurement of relative permeability and the practical significance of this knowledge. Laboratory flow tests are essentially model studies; the gross reservoir being represented by a small rock sample. It is necessary to simulate in experiments all the factors of importance which influence flow in the reservoir, as well a.; to eliminate effects peculiar to the model studied to assure measurement of valid flow behavior. Factors which affect the measurement and behavior of fluid flow in porous materials have been studied by other investigators.3,7,8,9,10,11 This analysis is not intended to evaluate fully all factors involved, but to establish first the validity of measurements by the technique used and then study flow behavior under various conditions. The studies reported are as follows: 1. Effects of pressure gradient, 2. Effects of gas expansion in tests conducted at near atmospheric pressure, 3. Effects of migration of a partial water saturation in oil-gas-water systems, 4. Effects If wettability characteristics of the system. and 5. Effects of the fluid saturation history. The first three are important only in laboratory measure-

Jan 1, 1951

By D. R. Parrish, T. M. Geffen, R. A. Morse, W. W. Owens

Laboratory studies of several factors affecting measurements of relative permeability were made using the three-section plastic-covered core technique. Results show that the core assembly, properly constructed, will perform as a single unit, and that the testing technique will, under suitable conditions of pressure gradient, gas expansion, and migration of partial water saturation, permit measurement of flow characteristics not affected by technique. Wettability equilibrium is readily established in cores exhibiting strong wetting preference to water or oil when initially saturated with water. Laboratory tests must be conducted so that saturation changes represent those that occur in the reservoir. Immediate implications of saturation history are (1:) that the possibility exists of increasing the displacement efficiency of solution gas drive reservoirs over the natural process, and (2) residual gas saturations following water flooding in gas or gas condensate reservoirs will be 15 to 50 per cent pore space rather than 1 to 11 per cent as generally believed. INTRODUCTION Solutions of petroleum reservoir problems pertaining to production performance require the use of true relative permeability characteristics. 'This relationship of fluid conductivity and saturation has been obtained by reservoir engineers in four ways, namely: 1. From past gross reservoir performance and the extrapolation of this data based on experience,1,2 2. By using published fluid flow relationships obtained in laboratory studies on general type porous materials,3, 4, 5 3. By attempting a mathematical derivation of flow behavior," using some experimentally obtained characteristics of reservoir rocks, and 4. By laboratory flow tests using representative rock samples of a reservoir. The first three methods listed above have shortcomings which make their use limited or questionable. Production characteristics of only certain processes are obtained from field data and these are not available at the beginning of a reservoir's producing life, at which time they are desirable. It is fortuitous if general fluid flow characteristics obtained experimentally have accurate application to specific field problems. Also, it is felt that at this time there is not sufficient knowledge of the flow behavior of oil, water, and gas in porous materials to enable applicable analytical description of this to be made based on other measured rock characteristics. Measurement of relative permeability in the laboratory offers the only direct method subject to adequate checking for determination of flow characteristics applicable to field problems. Primarily, this paper deals with laboratory experiments to establish the effects of several factors on the measurement of relative permeability and the practical significance of this knowledge. Laboratory flow tests are essentially model studies; the gross reservoir being represented by a small rock sample. It is necessary to simulate in experiments all the factors of importance which influence flow in the reservoir, as well a.; to eliminate effects peculiar to the model studied to assure measurement of valid flow behavior. Factors which affect the measurement and behavior of fluid flow in porous materials have been studied by other investigators.3,7,8,9,10,11 This analysis is not intended to evaluate fully all factors involved, but to establish first the validity of measurements by the technique used and then study flow behavior under various conditions. The studies reported are as follows: 1. Effects of pressure gradient, 2. Effects of gas expansion in tests conducted at near atmospheric pressure, 3. Effects of migration of a partial water saturation in oil-gas-water systems, 4. Effects If wettability characteristics of the system. and 5. Effects of the fluid saturation history. The first three are important only in laboratory measure-

Jan 1, 1951

By A. W. Furbank

IN reviewing the aerial cameras produced in different countries, it becomes apparent that in nearly all of them an attempt has been made to secure the greatest possible angle of view. This angle, of course, is determined by the objective. The objectives most commonly in use in aerial cameras have a maximum angle of 65º. The objective developed for this new Zeiss camera combines freedom from distortion and brilliant definition, with an angle of 95º. Aerial mapping, it is claimed, has been placed on a different economic basis, and new possibilities presented, particularly in connection with automatic stereoscopic plotting instruments, to which some short references are made. One way of enlarging the angle of view is to couple several instruments with their axes convergent, thereby producing a multilens camera. Typical of cameras of this sort in the United States is the Bagley four-lens camera, which later was developed into the five-lens camera (T3-A) of the U. S. Air Corps. More recently, in order to get away from the unfavorable Maltese cross image field of the five-lens camera, and to obtain a more practical form, two five-lens cameras were combined. By using them in tandem and rotating them by 45º relatively to each other, a ten-lens camera was produced, covering an octagonal ground area, with a total angle of view of 140º. Similar designs have been evolved in other countries. In all of them, however, a number of difficulties have arisen, quite apart from their large weight and high cost. Because of their complex mechanism, numerous shutters and magazines, and the high precision with which these parts must be interadjusted and synchronized, these cameras are far from dependable Moreover, a multilens camera by itself does not yet constitute a complete outfit for producing pictures suitable for photogrammetric survey. Because all the component pictures, except the central one, are obliques, it is always necessary to employ rectifying apparatus which transforms the marginal views to the perspective of the central one. In multilens cameras with many individual magazines, it is not convenient to

Jan 1, 1938

By William Kelly, Frederick Laist

The slow, tedious and costly method of reducing copper matte to metallic copper in the reverberatory furnace, commonly known as the Welsh process, was displaced by the rapid and inexpensive converter process about fifty years ago. The art of refining copper was for many generations a carefully guarded secret among the Welsh furnacemen and was handed down among them from father to son. An attempt was made to apply it at Butte when the smelting of copper ore first started there but it proved too difficult and expensive under local conditions, and until the introduction of the converter process the entire output of copper was shipped to Swansea in the form of high-grade (60 per cent) matte. Before the construction of the Manhes converter, attempts had been made to reduce copper matte in the bessemer steel converter, but these failed, chiefly because the air was blown through the bottom of the vessel. The air holes became clogged with chilled copper as soon as the reduction started. Manhes partially overcame this difficulty by placing the tuyeres in the side of the vessel, some, distance above the bottom, thus allowing space beneath them for the copper to accumulate. Nevertheless the first attempts to operate such a converter at Butte were not successful, as no means had been provided for clearing away obstructions, which formed to some extent in front of the tuyeres. This difficulty was overcome by drilling holes in the outside wall of the air chamber directly opposite the holes in the shell and lining, so that these could be punched

Jan 1, 1934

By E. H. Sellards

PHOSPHATE rock like most other mineral substances is found in nature in varying degrees of purity. Of the impurities that are present some are constituents of the rock itself; others are inclusions of a foreign substance within the rock; while still others represent merely associated materials or minerals, either clinging to the rock or found in cavities and natural depressions, and hence largely removed in mining. Some of these impurities are distinctly deleterious to the processes of manufacture for which the phosphate is mined, while others, although neutral in action or nearly so, yet by their presence reduce the average grade of the rock and thus acid useless bulk to the shipment. It is the object of refined processes of mining to bring the product, as delivered from the mine, to the highest possible grade consistent with the market requirements and demands. This, however, is not accom-plished without actual loss in the form of discarded phosphate. It is evident, therefore, that the devising of methods for reducing this loss in mining, and yet maintaining the grade of the rock which the market requires, is one of the serious problems that the producers have to face.

Jan 9, 1914

By Henry G. Granger

It still rains in the Choco! I well remember one evening a dozen years ago, while traveling toward the town of Negua in a small champa or dug-out canoe, the rain fell so heavily that I had to work my hardest to bail out the water with a large totuma or gourd in order to keep the canoe afloat, the native boatman meanwhile plying his paddle in the stern. If any one thinks bailing is easy work, let him scoop out a quart or more at a stroke, 40 times a minute for half an hour, and I venture that he will change his opinion. These small canoes required only one paddler to make the 3 miles an hour which is the standard rate of aquatic progress on the Choco. Another time, on the Atrato river, about six o'clock in the afternoon, the rain fell so heavily that an empty gourd, 9 in. in diameter and 4.5 deep, was filled to the brim in 90 sec., timed by a watch. Such downpours are typical, but unless caught in one it is not specially noticed. These downpours seldom last more than an hour, and frequently cover only a limited area, occasionally falling on one bank of a river and not on the other. During the night-time, the rain, if gentle, will usually last until dawn, and sometimes an intermittent drizzle will keep up all day as well, although, as a rule, it rarely rains during the day. The rise of the rivers, due to the rain-fall, varies from a few inches to several feet. One night in August, 1899, the spuds of the dredge Margaret, operating on the Atrato river, showed a rise of 16 ft., and for 3 days thereafter occurred the greatest flood known in that district for 32 years. The dredge had all three spuds down, and the 2-yd. shovel dragging 011 the bottom. A 0.75-in. cable fast to a stout tree, 700 ft. away, stretched tight

Jan 1, 1909

By Victor Lenher

The interest shown recently in selenium and tellurium has brought many requests for an assembling of the analytical chemistry of these two elements. The intention of this paper is to discuss all of the chemical principles utilized in the detection and quantitative determination of these elements, as well as to describe the works methods actually followed by producers of tellurium and selenium in the United States. These methods have been furnished by S. Skowronski of the Raritan Copper Works, H. D. Greenwood of the United States Metals Refining Co., F. F. Colcord of the U. S. S. Lead Refinery, and E. W. Rouse and A. E. Hall of the American Smelting and Refining Company. Occurrence Selenium is found associated with sulfur, to which in many respects it is quite similar. Occasionally deposits of native sulfur, notably those in the Lipari Islands, Kilauea, and Japan, show a red-brown coloration, I which is readily distinguished from that of other sulfur; this red-brown * sulfur contains a small amount of selenium. Not infrequently, the , sulfides of the heavy metals are accompanied by selenium and tellurium, • presumably as selenides and tellurides. The Scandinavian pyrite, which is one of the large sources of European sulfuric acid, when roasted has fur- - nished a large part of the selenium that has come to the United States; it I was in flue dust from the roasting of Scandinavian pyrites that the element was discovered by Berzelius in 1817. Greek and Spanish pyrites also

Jan 1, 1923

By Victor Lenher

The interest shown recently in selenium and tellurium has brought many requests for an assembling of the analytical chemistry of these two elements. The intention of this paper is to discuss all of the chemical principles utilized in the detection and quantitative determination of these elements, as well as to describe the works methods actually followed by producers of tellurium and selenium in the United States. These methods have been furnished by S. Skowronski of the Raritan Copper Works, H. D. Greenwood of the United States Metals Refining Co., F. F. Colcord of the U. S. S. Lead Refinery, and E. W. Rouse and A. E. Hall of the American Smelting and Refining Company. Occurrence Selenium is found associated with sulfur, to which in many respects it is quite similar. Occasionally deposits of native sulfur, notably those in the Lipari Islands, Kilauea, and Japan, show a red-brown coloration, I which is readily distinguished from that of other sulfur; this red-brown * sulfur contains a small amount of selenium. Not infrequently, the , sulfides of the heavy metals are accompanied by selenium and tellurium, • presumably as selenides and tellurides. The Scandinavian pyrite, which is one of the large sources of European sulfuric acid, when roasted has fur- - nished a large part of the selenium that has come to the United States; it I was in flue dust from the roasting of Scandinavian pyrites that the element was discovered by Berzelius in 1817. Greek and Spanish pyrites also

Jan 1, 1923

By Arthur F. Wendt

The earliest knowledge of copper-ores in the Southwest was derived from the Mexicans, who, in the latter part of the last century, discovered and worked the Santa Rita copper mines, now situated

Jan 1, 1887

By H. S. Price, D. A. T. Donohue

The system of equations describing displacement of a hydrocarbon liquid by a hydrocarbon vapor in a porous medium where mass transfer takes place between the phases is solved numerically for a variety of gas injection processes. Even though the method of solution is quite general, only systems with three hydrocarbon components are considered. Computer simulations of displacement processes wherein mass transfer between phases is both considered and neglected are compared, and it is shown that neglecting mass transfer can give pessimistic displacement efficiencies. INTRODUCTION The role of the gas displacement process in the recovery of petroleum has been subjected to a series of detailed analyses; as a result, a number of predictive models have been published in the literature. However, because of major simplifying assumptions, most of these models do not completely represent the physical system. As a result, the effect of making the simplifying assumptions is unknown. Therefore, a complete representation of this process — one without major simplifying assumptions —should lead to a fuller understanding of the process, and perhaps to methods of improving it. The general method of developing a model for two-phase fluid flow in a porous medium is to solve simultaneously the continuity equation, the energy equations and the equation-of-state for each phase under the prescribed initial and boundary conditions. For an isothermal system, the energy equations reduce to the momentum equation. Darcy's law. However, since natural gas is the vapor state of the reservoir liquid, interphase mass transfer may take place with concomitant changes in both the intensive and extensive thermodynamic properties of each phase. It is this phenomenon that has often been omitted in previous mathematical models. An additional relation, then, which accounts for mass transfer between the phases, must be included with the other equations to specify a complete model. Completely formulating the equations to be solved is not a difficult task1 but obtaining their solution has been intractable up to now. Availability of large-memory, high-speed digital computers now makes an attack on this formidable problem possible. This paper presents a preliminary study of the problem. Since this investigation is intended to be exploratory, it is restricted to the linear, horizontal, isothermal, two-phase viscous flow of oil and gas in an oil reservoir. In the early development of predictive models of this process, the reservoir system was considered as a unit and various forms of the material balance equation were proposed.2-4 Pressure and saturation gradients were then added in the Buckley-Leverett model.5 The Buckley-Leverett formulation considered the fluids to be incompressible; thus, the mathematical model reduces to a steady-state system. In the 1950's, studies incorporating numerical techniques were being published.6-9 These mathematical models differed in the efficiency of finite difference techniques, the inclusion or exclusion of capillarity or the number of space dimensions considered. To solve these nonlinear, partial differential equations, each phase was considered to be homogeneous with time; therefore, mass transfer between phases was neglected. The effect of mass transfer on the gas displacement process was first reported by Attra. 10 He simulated the one-dimension flow system by a series of cells in each of which the fluids were equilibrated during a time step. In addition, the pressure throughout the system during each time step was predetermined and constant-phase velocities were calculated according to the Buckley-Leverett incompressible fluid flow model. Welge et al.11 developed a model for the displacement of oil by an enriched gas where composition is considered to be a dependent variable. Fluid

By B. M. Bird

DURING the past four years the experimental work in coal washing carried on by the U. S. Bureau of Mines and the University of Washington has been devoted mainly to the development of special methods for the tabling of fine sizes of coals that are difficult to wash. One important outgrowth of this investigation has been the application of hindered-settling classification to coal tabling. Although used for many years in ore dressing, the term "classification" as used here may be new to many readers. It may be defined as the separation obtained when a bed of particles is held in a uniform state of suspension in an upward current of water, either continuous or pulsating, just sufficiently strong to keep the bed in a mobile condition. A common example of this type of separation is a jig in which there is no suction stroke. When the hindered-settling classifier is used with the coal-washing table, the fine-size raw coal, instead of being fed direct to tables, as is the prevailing practice, is first fed to the classifier and grouped, according to the rate of settling against the upward current of water, into perhaps six separate products. After dewatering, each of these except the sixth, a refuse product, is elevated to a seperate feed bin and washed on a separate table. This paper gives a brief discussion of the basis for the use of hindered-settling classification of a table feed; a description of the experimental work; a comparison of the results obtained with and without classification; and a discussion of the application of the classifier in commercial coal washing.

Jan 1, 1928

By C. H. Mathewson

Discussion of the paper of C. H. MATHEWSON and ARTHUR PHILLIPS, presented at the New York meeting, February, 1916, and printed in Bulletin No. 109, January, 1916, pp. 1 to 50. ZAY JEFFRIES, Cleveland, Ohio (communication to the Secretary*).¬The authors are to be congratulated for this interesting and valuable contribution. The paper as a whole shows very careful experimentation coupled with rare judgment in drawing conclusions. I have been working along similar lines for the last two years with other metals and alloys. In a short conversation with Dr. Mathewson about July 1, 1915, he mentioned the fact that different degrees of cold work greatly affect the temperature of recrystallization on annealing, Later I determined the recrystallization temperatures of iron, mild steel, and copper, with different degrees of cold work and found that the greater the degree of cold work, the lower the temperature of recrystallization on annealing. In the course of these experiments, I conceived practically the same ideas regarding the reasons for recrystallization as those advanced in the article under discussion. After a metal has been reduced by cold work to about one-fourth of its original area, the differences in orientation of different parts of a given grain can be seen plainly at a magnification of about 1,000 diameters. It is interesting to note that in Fig. A, Plate I, the lines of deformation are not parallel. For example,. in the large grain at the lower left corner of the micrograph, if the lines of deformation about 3g in. from the left edge are continued in a straight line, this line will intersect a straight line drawn as a continuation of the lines of deformation on the extreme right of the grain, at an angle of about 20°. Similarly, if the lines of deformation at the extremities of the large grain in the right central portion of the micrograph are extended, the lines intersect at an angle of about 35°. The individual lines of deformation are not straight. In some of these the parts of the broken lines intersect at angles as great as 15°.

Jan 5, 1916

By Charles T. Van Winkle

Until the advent of the porphyry coppers and the introduction of flotation which soon followed, crushing and grinding for many years proceeded along somewhat stereotyped lines, without important alteration in type of machinery. For the finer crushing and grinding, stamps, rolls, and various patterns of Huntington and Chilean mills were in general use. Ball-mills were in use abroad, but owing to their small capacity and the high cost of screens and steel, they never obtained much footing in the United States. Tube-mills were first introduced into the crushing departments of cyanide plants when it was found that for crushing finer than 30-mesh other types of crushing machinery were not efficient. In order to crush with one pass, these mills were made 18 to 22 ft. (5.5 to 6.7 m.) in length. Pebbles were used as a grinding medium and the mills were lined with either silex blocks or fragments of quartz or flint pebbles set in cement. While the cylindrical tube pebble-mill had been used to some extent in small installations of concentration mills, the first instance of its use on a large scale was at the concentrating plant of the Miami Copper Co., where 8-ft. by 22-in. (2.5-m. by 55.9-cm.) Hardinge mills were tried out against Chileans. The results of these experiments led to the gradual replacement of the Chilean by the Hardinge mill. Robert Franke published an article' describing the work done, comparing the two types of mills. At the same time, according to Franke, a test was run using a 6-ft. (1.8-m.) Hardinge ball-mill as a substitute for rolls for intermediate crushing on 1/2-in. material. According to Franke, this mill was soon discarded, since it was found that to obtain the desired product the mill must be limited in capacity. The Miami Copper Co. made no test with other types of ball- or pebble-mills. Following this example, others installed the conical type; and when the Inspiration Consolidated Copper Co. decided to build a concentrator, it adopted the conical mill. As the requirements for mills would be very large, it purchased manufacturing rights in the State of Arizona from the

Jan 1, 1918

By Kenneth K. Humphreys, J. W. Leonard, T. S. Spicer

INTRODUCTION Reasons for Thermal Drying The continuing increase in the percentage of - '/4 in. ( -6.3 mm) coal produced as a result of the increased use of mechanical mining methods has, over the years, tended to shift considerable portions of the work of producing salable coal to the fine coal cleaning section of the preparation

Jan 1, 1979

By Francis Rich

BEFORE the world-wide depression, the primary purpose of most blast-furnace operators was to produce a maximum tonnage of pig iron per day for each furnace in blast. Some attention was paid to the conservation of labor and raw materials, but the idea was well established that low-cost pig iron was attainable only when each furnace was pro-ducing a high tonnage. After the depression had set in, the picture changed considerably. Each blast-furnace operator was forced to run his plant in a manner that best fitted the economical set-up of his company. A great deal of thought was expended on the different methods of operation, always with the idea of making each product in a way that would best serve his company financially. Because of this abnormal condition, the blast-furnace man was compelled to indulge in various practices of which many had been believed to be next to impossible up to that time. The ultimate purpose of these innovations was either one or a combination of the following: 1. To produce only enough pig iron for immediate consumption at a minimum cost. 2. To produce gas for boiler or mill use to supplant some higher priced fuel. 3. To consume the coke produced at the coke plant, which was often viewed as a byproduct. 4. To protect the cash position of the company. These conditions were met by diverse methods, some of which were: 1. Slow or decreased wind. In some instances the blast blown was held as low as 25 per cent of the normal volume. 2. Intermittent operation, in which the furnaces were shut down or "fanned" at frequent intervals.

Jan 1, 1935

By John P. Harmon

This paper was written with two objects in view: (1) To describe in detail what has been done toward the ventilation of the main unit of the Portovelo mines and the results; (2) to give information that may be useful to anyone who may have to make a preliminary mine ventilation survey, with recommendations for the improvement of the existing system and finally the maintenance of the improved system. General Description The mining operations of the South American Development Co. at Portovelo, Province of El oro, Ecuador, are described here only briefly, as a full discussion does not fall within the scope of this paper. The orebodies are of the steeply dipping, gold quartz vein type, averaging about 2.0 meters wide. As shown in Fig. 1, the ore chutes are relatively far apart, making considerable development work necessary before connecting raises can be driven between the levels. Faulting' on a large scale and a parallel vein system have made long dead-end drifts and many crosscuts necessary in the exploration of veins. The ventilation of these dead ends is described under Auxiliary Ventilation. The method of mining2 is the filled rill stope method, similar to the method that is largely employed at the Butte mines. The main shaft of the mine is in the Amarillo Valley, on either side of which mountains rise abruptly to a height of several hundred feet above the collar of the shaft. Entrance is made to the mine: (1) Through the American shaft, which extends vertically from the surface to a depth of 1100 ft., of which only the first 700 ft. are in active use at the present time; (2) levels are driven from the American shaft at intervals of 30 m. (100 ft.), of which only the third, fifth and seventh levels need be considered in the ventilation problem; (3) adits at intervals of 30 m. (100 ft.), with a few exceptions, above the collar of the American shaft.

Jan 1, 1931

By F. J. Plecity, W. C. Leslie, F. W. Aul

During isothermal recrystallization, the rate of grain growth in dilute Fe-hlo alloys decreased rapidly with increasing Mo content, up to -0.04 at pct, and less rapidly therea-fter. Rate of growth also decreased sharply with time at constant temperature. The observed rates of boundary migration did not cor,espond to predictions of the Lucke-Detert theory. It is proposed that the growth of recrystallized grains is inhibited by clustering of solute atoms at inzperfections in the unrecrystallized matrix. It is now firmly etablished" that the rate of re-crystallization of cold-worked metals, i.e., the rate of growth of recrystallized grains into the deformed matrix, is greatly inhibited by the presence of alloying elements in solid solution. The effect is greatest with the first very small quantity of alloying elements, and additional increments cause much less pronounced retardation of growth. The early papers on this subject were reviewed in Ref. 6. The mechanism of retardation of growth is not clear; only one theory, due to Lucke and Detert? has been advanced. This assumes an elastic interaction between grain boundaries and solute atoms which tends to increase the concentration of the latter in the grain boundaries. Except at very low solute concentrations or at high temperatures, the mobility of the boundary is assumed to be controlled by the rate of diffusion of the accompanying solute atoms. Abrahamson and Blakeney2 have noted a correlation between "recrystallization temperature of binary alloys of iron and the number of d-shell electrons in the solute atoms. There is need for considerably more experimental data on the effect of solute elements on the rate of migration of grain boundaries into the deformed matrix, to provide the basis for an understanding of the annealing process in metallic solid solutions. Only a start has been made in this direction. To avoid unnecessary complications, alloys in which precipitation does not occur should be used, but to produce the maximum effects it is desirable to select alloys with a large difference between the sizes of the atoms of the solvent and solute. For these reasons, alloys of iron and molybdenum sen for this study. MATERIALS AND PROCEDURES A 30-lb. ingot of iron and four similar ingots of Fe-Mo alloys were vacuum melted in magnesia crucibles and poured into cast-iron molds. The molybdenum contents were planned according to the results of Abrahamson and Blakeney2 sothattwoalloyswould fall in the region of rapid change of recrystallization kinetics with change in composition (0.006 to 0.015 and 0.030 to 0.045 at. pct Mo) and two alloys would fall in the region of gradual change (0.18 to 0.24 and

Jan 1, 1962

By Fred Wise

THE Getchell mine, a comparatively recent gold discovery, is in the old Potosi mining district, Humboldt County, Nevada. All ore is mined from open pits using Diesel shovels and gasoline trucks. Two types of ore are mined, oxide and sulphide. Oxide ores are siliceous or shaly; sulphide ores either gougy, siliceous or shaly. In mining, the sulphide ore is segregated into hard and gougy ore, because the gouge must be dried before it can be crushed, The oxide ore is not segregated. GENERAL METALLURGY The oxide ore is the leached outcrop that overlies the sulphide ore body. All of the iron and arsenic sulphides found in the sulphide ores have been thoroughly oxi-dized, The sulphur and arsenic have been leached out while the iron is present as hematite and limonite. The oxide ore is amenable to direct cyanidation, and although no visible free gold is present it is released at a comparatively coarse grind. The sulphide ore is more refractory, since the gold is all of micron size and some of it is locked in fine sulphides. It has been established microscopically that the free gold is coated with an impervious shell, which is probably some form of iron compound. The sulphide ores contain from 1.5 to 2 per cent of arsenic, which is present as orpiment and realgar with minor amounts of arsenopyrite. The orpiment and realgar are of a later mineralization than the gold and are barren. Roasting and washing of the sulphide ore prior to cyanidation is necessary to eliminate the arsenic, to alter the gold coating from an insoluble form to a soluble form, and to release the gold associated with the fine sulphides. Washing the ground calcine in weak sulphuric acid, trona, or hot water are beneficial in the order named, but to date the water is the best from an economic standpoint. Metallurgical tests as well as plant practice indicate that a certain amount of gold cannot be recovered even by going beyond economic practices, On this basis metallurgical results are viewed in the light of an optimum tailing rather than a per-centage of extraction.

Jan 1, 1940

By T. G. R. Rawlins, L. E. Brosselard

Direct platinum carbon replicas have been used to study substrates prior to growth and after initial nu-cleation of the layer. Replicas have been directly stripped and correlations have been made with other replica techniques. Mechanically polished substrates are very flat with occasional areas of "dirt", which is apparently silicon. When such substrates are etched in hydrochloric acid gas, scratches and hexagonal defects (thought to be polishing compound) are revealed, together with areas of apparent redeposition. Chemically polished substrates are much less flat although much more homogeneous in appearance. Heat treat)nents have no effect. Nuclei deposited on these surfaces, using a normal silicon tetrachloride system, have been examined. Nuclei on mechanically polished subsrates occur in random areas only, whereas on chemically polished surfaces they are more uniformly distributed. THE interest in the study of thin films and now their rapidly expanding use in many fields has increased over a period of years. Much of this current interest, particularly in the field of single-crystal or epitaxial thin films, has derived its stimulus not only from possibilities for application but also from fundamental electron-microscope studies which have indicated the manner of growth of such layers from the initial nuclei.1-5 Previous work involving study of growth processes may be divided into three categories. First, vacuum deposition, primarily of metals, on a variety of substrates has been studied by electron microscopy and electron-diffraction techniques. These have shown the three-dimensional aspect of nucleation and the remarkable liquidlike behavior of the growing nuclei which coalesce to form a complete layer. More recently this work has been expanded in two ways: by growth inside the electron microscope this has obvious advantages for kinetic studies; and by growth in ultrahigh vacuum—much of this work has been done on semiconductors.8-11 It is of interest to note that metals, specifically gold deposited on rock salt, will form only polycrystalline layers in ultrahigh vacuum unless the substrate surface is contaminated.12 In general the mode of growth for vacuum-deposited semiconductor films is the same as that for metal films. The second method of growth that has been studied is that of electrodeposition.13,14 The little that has been published suggests that the mode of growth is similar to the vacuum case, except that irregularities may perturb the electric field and disturb the growth process. The third and last primary method of growing epitaxial layers is by use of chemical methods. These techniques have generated much interest and much has been published on them. Considerable electron-microscope work has been done on the defects in the layers; however comparatively little work has been undertaken on the initial nucleation and early stages of growth. Confining ourselves now exclusively to the case of silicon, Charig et a1.15 have considered the growth of silicon on silicon substrates by hydrogen reduction of trichlorosilane, and studied the films by means of replica and transmission techniques. Subsequently they have studied the same system for growth on quartz,16 and with the addition of pyrolysis of silane on quartz and alumina.17 Also Manasevit el al. have studied deposits using silane and silicon tetrachloride on sapphire.18-14 Finally, in this volume studies of deposition on beryllia and sapphire are reported. Although Revesz and Evans20 have examined complete layers, grown by means of the widely used silicon tetrachloride reaction, no detailed examination similar to that published by Charig and Joyce21 for the trichlorosilane system has been given. Therefore this investigation has examined substrate surfaces prior to growth and then nucleation on these surfaces for the silicon tetrachloride system. EXPERIMENTAL In this work the surfaces have been studied by means of standard replica techniques. Because of the very real problems associated with artifacts introduced,22 different replicas and different cleaning

Jan 1, 1967