Search Documents

By Clarence E. Jackson, George G. Luther

THE ever increasing array of information concerning the measurement of the effect of the welding process on the properties of a steel is an indication of the tremendous effort that is being expended in this field. The methods that have been considered may be divided into two groups: first, those that measure directly the effect of welding on the ductility of a steel, and, second, those that observe the change in some property, such as the hardness of the heat-affected zone, and assume a direct correlation between this change and the resultant ductility. The nick-bend test is a direct method designed for studying the effect of welding on the ductility of a steel. The test specimen (Fig. I) consists of a bar cut from a plate with a bead weld on the surface. The specimen is prepared with a saw-notch placed so as to restrict deformation to the heat-affected zone under the bead weld when tested as a static bend. Failure is caused by rupture of the low-ductility metal in the heat-affected zone. The angle at maximum load is used as an index of the effect of the welding process on the material. In the development of the nick-bend test considerable scatter was noted in some of the results, although the agreement of duplicate specimens welded at the same time and tested consecutively was excellent. Upon further investigation it was found that the change in ductility was dependent upon the interval of time between the welding operation and the testing of the specimen. For the six steels of Fig. a, the angle at maximum load in four cases was doubled and in one case was tripled. All steels that have been studied show an improvement in the angle of bend for longer intervals between welding and testing. This same behavior has been found in weldability tests using the Navy T-bend

Jan 1, 1945

By Charles Fulton

This paper describes experiments carried on at the Case School of Applied Science, together with their results. Their success led to the design of the larger furnace herein described, but which has not been built. A PREVIOUS article' by the authors contained a general description of the new roasting furnace herein described but it did not go into detail as to the metallurgical behavior or the results obtained. Believing that such information would be of great value, they have elaborated on the subject and have given many unpublished details. The furnace described applies the principle of roasting finely divided zinc-sulfide ores, now produced in large quantity by the flotation process, in gaseous suspension; that is, the ore particles are carried, in suspension, in a current of air and gaseous products of the roast. The relatively great fineness of flotation concentrate presents difficulties and problems of roasting in furnaces of the ordinary type; the fine ore is forwarded through the furnace in the form of a shallow bed and its very fineness leads to dense impervious bedding which prevents oxygen from reaching the interior of the bed, thus unduly lengthening the time of roasting and preventing the elimination of the last of the sulfur. The fineness of the concentrate, normally, should lead to a rapid and complete roast, for the speed of roasting is a function of the surface exposed to oxygen, which surface is greatest, per unit of weight, in very fine material. The difficulty in bed roasting is to get the oxygen to the particle. If the fine ore, during the roasting, could be freely suspended in oxidizing gases, full advantage could be taken of the great surface conferred by its fineness. This fundamental idea, of course, is not new, for the Stedtefelt furnace, familiar to the older metallurgists, is an example of it; but the manner in which this is accomplished may be new.

Jan 10, 1924

By M. L. Fuller

DURING the last several years many papers have appeared dealing with the structure of highly polished metal surfaces The awakening of interest in this subject is due to the applicability of the electron diffraction technique to the study of surfaces The original theory of Beilby1 considered the surface of polished metals as of the nature of a super-cooled liquid or a vitreous, amorphous solid The electron diffraction effects from polished metals have been interpreted by many to be a direct experimental proof of the correctness of the Beilby theory This interpretation has been strongly opposed by others, so that at the present time the subject is in an uncertain and controversial state In the present paper new, and hitherto unpublished, electron diffraction effects from polished zinc are described These observations indicate that the polished surface of zinc is crystalline PUBLISHED WORK Many papers2-10 have interpreted the electron diffraction evidence as proof of the Beilby amorphous theory All investigators agree that highly polished metals give rise to two diffuse diffraction haloes, similar to those obtained by the diffraction of X-rays in liquids and vitreous solids It is this similarity that leads to the amorphous-layer interpretation of polished metals Strangely, the interatomic distances calculated from these haloes are very similar for the various metals investigated, in spite of a rather wide range of such distances in the crystalline and liquid states The calculated atomic sizes are, furthermore, smaller than are experienced in the normal states of the metals In spite of these anomalies, the amorphous-layer interpretation has been adhered to by many One investigator, S Dobmski,11 differs from the others in his experimental results By polishing under benzene in order to avoid the possibility of oxidation, Dobinski obtains diffuse haloes of [radire] different from those previously obtained He thus obtains a more rational quantitative correlation of-the diffuse haloes with the amorphous-layer theory

Jan 1, 1938

By John McDonald

THE amount of published literature in the field of mechanical proper-ties of magnesium alloys is not great; particularly with respect to rolled alloys. Haughton and Prytherch1 have summarized most of the articles to 1937, including their own work on sheet. Although many papers can be found dealing' with the technology of magnesium and the alloys now in commercial use, there does not seem to be any work dealing exclusively with the variation in properties of rolled alloys as caused by changes in alloy composition. Comparison of published data reveals considerable discrepancies in, properties of alloys of the same composition, probably due to differences in the details of working and heat-treating followed by different workers. The purpose of this paper is to study the proper-ties of alloys in conditions where the effect of such differences have been eliminated. It is well known that the strength and ductility of metals are functions of the working and heat-treating they have received, as well as of their chemical composition. In comparing alloys with respect to these proper-ties, therefore, all possible combinations of the variables of the fabrication procedure ought to be carried out on each alloy. One or more of these treatments will produce the highest ductility, or strength, or both. These highest properties would then be selected as characteristic of each alloy, and alloys would be compared on the basis of those properties. Thus a separation of the effect of composition and that of working and heat-treating would be achieved. In this paper, however, a compromise with completeness has been made by carrying out a restricted number of treat-ments. As a consequence, the properties obtained are not necessarily the best that the alloy is capable of exhibiting; but since all alloys have been treated by the same method, the results ought to be comparable. The elements selected for the study comprise a class that will alloy easily with magnesium, and that are relatively cheap. Each was added in different amounts, up to a limit that varied with the element.

Jan 1, 1939

By Frederick Laist

While remodeling No. 1 section of the concentrator at the Washoe Reduction Works of the Anaconda Copper Mining Co. during the summer of 1912, for the purpose of ascertaining what additional metal recoveries could be made by improvements in concentration practice which had been developed by the staff of the Boston & Montana Reduction Department, at Great Falls, it was deemed advisable to carry on some experiments on the treatment of the regular mill tailings by roasting and leaching, to see whether the losses of metal values might not be still further decreased. In the course of these experiments about 5,000 tons of tailings were roasted, and of the resulting calcine about 200 tons were leached. The results were so satisfactory that it was decided to continue the work on a larger scale, particularly as regards the leaching end of the process, and construction work on an 80-ton roasting and leaching plant was accordingly commenced during the latter part of February, 1913, and is being pushed as rapidly as possible. 80-Ton Leaching Plant. This plant will consist of one 20-ft. roasting furnace of the Mac-Dougall type, specially adapted to the work of roasting for leaching; two leaching tanks, 32 ft. in diameter by 12 ft. deep, together with the necessary solution tanks, air lifts, precipitating launders, etc. It has been decided to precipitate the copper from solution on scrap iron, so as not to hamper the roasting and leaching departments by any weakness that might develop in the precipitating department. It is, however, the intention to experiment with a number of different methods of precipitation; for example, by electrolysis and by hydrogen sulphide. The acid required for the operation of this plant will be purchased, ad the quantity required is not sufficient to justify the installation of an acid plant. An acid plant will, however, be established in con-

Jan 1, 1914

By R. A. Hadfield

The present tribute to a great pioneer in the steel industry, with the accompanying remarks upon the town of Sheffield, which has remained to this day what his invention made it, an important center of that industry, originally formed a part of the paper on "Iron Alloys," prepared, at the invitation of the Council of the Institute, for the Chicago meeting of August, 1893. That paper, begun with the intention of dealing with many alloys of iron, became, of necessity, through the limitations of time on the part of the writer and of space in the Transactions of the Institute, mainly a discussion of the principal modern commercial alloy of iron, manganese-steel; and much introductory and general matter was consequently omitted. The Secretary suggested, however, that this particular portion would be interesting and appropriate as a separate contribution, and I therefore present it as such, offering the foregoing statement simply as an explanation of its incomplete character. If I had undertaken to write a paper upon this subject alone, I should have felt myself bound to bestow upon it more elaborate research and to treat it with more abundant details. It was in the immediate neighborhood of Sheffield that the first successful process for the fusion of steel on a commercial scale saw the light. The late Dr. Percy, a leading authority in general metallurgy, says: " Formerly, so far as I am aware, steel was never melted and cast after its production; and in only one instance, viz., that of wootz was it ever molten during its production.....Now, by the fusion and casting of steel after its production its heterogeneousness is remedied, and ingots of the metal may be procured of perfectly uniform composition throughout; and for the practical solution of this important problem we are indebted to Benjamin Huntsman, of Sheffield." As a recent American journal appropriately remarks: " Huntsman's patient efforts, at last rewarded with success, entitle him to an elevated niche among the heroes of industry. The invention of cast-steel was second

Jan 1, 1895

By E. T. Knight, John D. Gill

Much has been written and said concerning the alleged wasteful and uneconomic use of natural gas and petroleum. Espccially condemned has been the use of natural gas for the production of carbon black and the use of heavy fuel oil under steam boilers.' The critics of these usages of gas and oil have sought to make effective their verbal attacks on the industry by the repetitive expression of the words "inferior" and "superior" uses2 of petroleum. Thus, to employ natural gas for residential heating was to use it in a superior way; to use it for the production of carbon black was to use it in a wasteful and uneconomic way. To use petroleum for the production of automotive fuel was to use it in a superior way; to employ it as a residential fuel and as the prime source of power in an industrial plant was to use it in an inferior and uneconomic way. No doubt the objections to such employment of gaseous and liquid natural hydrocarbons originated in the belief that natural gas and petroleum are limited, nonregenerative mineral resources, and that the functions they perform can be just as well performed by other natural resources like coal13 of which practically unlimited reserves are known. The generations that have dominated each of the last four decades have counted reserves4 of petroleum in terms of a few years supply. Meanwhile, domestic demand for motor fuel rose spectacularly from a few million barrels in 1900 to more than 500,000,000 bbl. last year.5 The more imaginative and vocal critics drew startling word pictures of the catastrophe of 25,000,000 motor vehicles made useless and of the great automotive manufacturing and allied industries brought to an untimely end, and millions of workers left hopelessly unemployed by what they called the deplorably rapid depletion of the petroleum reserve. Many of the critics have been sincere advocates of the conservation of natural resources; many others, and in recent years probably the majority, have espoused the doctrine of conservation to promote their own self-interest rather than that of the public. The latest advocate of severe restriction in the use of petroleum for the alleged purpose of conserving the petroleum resource proposes to achieve that end by a bill,6 now before

Jan 1, 1938

By R. F. W. Pease, R. A. Ploc

A scanning electron microscope with a resolving power better then 100Å has been developed for the direct examination of surfaces. This instrument was used to study iron undergoing oxidation at 500°C. It was found that the electron current in the scanning electron microscope was low enough (about 10-atrzp) to have no observable effect on the growth of the oxide. "Armco " iron, when oxidized, exhibited an oxide film whose thickness and whiskey population varied with pain orientation; but purer iron, when oxidized, exhibited no such pain dependence and whisker occurrence appeared to be caused by impurities. UNTIL recently most surfaces of opaque specimens could either be studied with a light microscope or, if higher resolution was required, by viewing a replica of the surface in a transmission electron microscope. Direct electron microscopy of a surface has, in general, proved difficult owing to excessive foreshortening and the poor image quality obtained. The scanning electron microscope, however, offers an alternative method of directly viewing a surface without these disadvantages. At low magnification it offers a much larger depth of focus than the light microscope, and at high magnifications it offers much higher resolution (about 100Å). PRINCIPLE OF THE SCANNING ELECTRON MICROSCOPE A schematic diagram is shown in Fig. 1. The electron optical system consists of a gun followed by a series of lenses which focus the electron beam onto the surface of the specimen. The beam is scanned in a rectangular raster across the specimen surface and, by amplifying the secondary electron current from the 'pecimen, a picture of the specimen surface is built UP sequentially on the face of the display cathode-ray tube. The magnification of such a system is given by the ratio of the scan amplitude on the display cathode-ray tube to

Jan 1, 1965

By Frank Speller

WE are here to honor again the memory of Henry Marion Howe, one of the foremost metallurgists of his time, and it is indeed a great privilege to be called upon by the Board of Directors of .this Institute to give the memorial address this year. Professor Howe started active investigation of corrosion of iron from a metallurgical standpoint in 1887, and made several important contribu-tions to the subject from 1895 to 1908.(1) ? The papers named in the bibliography are only a few of his valuable papers, but in all his works he sets a high standard of scientific accuracy, together with a clearness and power of expression rarely equaled in engineering literature. There-fore it seems appropriate on this occasion to review the work on corrosion of this distinguished gentleman and then endeavor to make a brief inventory of what has been accomplished since his time. Howe saw the beginning of the steel industry in America and before he died (May 14, 1922) witnessed it develop to a production of 45,000,000 tons per year. He was naturally very much interested in the infant industry and was quick to see the importance of the question of corrosion. It was my privilege to discuss the subject of corrosion frequently with Professor Howe at various times from 1905 to 1908; in this, as in other metallurgical problems, he sought the truth without bias and always insisted on proving an opinion or conclusion before accepting it. We should remember that when Howe started his investigation of corrosion, in 1887, steel was rapidly supplanting wrought iron. Certain papers in the early eighties (now forgotten) claiming much greater durability for wrought iron than for steel aroused Howe's interest. He could not reconcile the statement that steel was intrinsically and incurably less durable than wrought iron with the continued and widening use of steel,

Jan 1, 1934

By J. H. Reynolds

The possibility of using a semiconductor, metal, semiconductor structure as a light detector is discussed. A brief theoretical argument is presented which predicts that this structure should have pho-toresponse characteristics similur to those of a metal-semiconductor diode, but with the magnitude of the current increased by a transistor gain factor. Measurements made at low frequencies on a particulur S-M-S device agree u~th this prediction aizd shoul that significant gain factors are attainable. The current gain is substantially higher than that predicted for the metal base transistor. It is proposed that the operation of these units is more closely approxinzated by the metal-gate model which predicts higher current gains. A qualitative discussion of its high-frequency performance indicates that detection of light modulated at microwave frequencies by a S-M-S deuice is possible. ADVANCES in the technology of chemical vapor deposition'-4 have made it possible to form a S-M-S structure consisting of a thin metallic layer sandwiched between layers of single-crystal semiconductor. It has been proposed5-7 that, if the metal layer is made sufficiently thin, this structure could be used in an amplifier having several advantages over presently available transistors including higher-frequency performance. Calculations8 predict that the maximum gain-bandwidth product is nearly an order of magnitude higher than that of a bipolar transistor having the same geometry. Maximum oscillating frequencies in the microwave range are predicted. Electrical measurements made on S-M-S devices have shown that, although the theoretical frequency characteristics are not presently attainable, current and power gain is obtained. Another possible application of the S-M-S structure is its use in a light detector. This structure is a three-layer relative of the metal-semiconductor diode. Light detection using M-S diodes is the subject of considerable present interest. They are known to have a short response time and the ability to detect light having a photon energy below the semiconductor bandgap. In this paper, the mechanism by which S-M-S photocurrent is generated is discussed. An expression is derived which shows that the response characteristics are similar to those of a M-S diode, but that the magnitude of the current is increased due to the transistorlike behavior of the device. The results of low-frequency response measurements on a particular S-M-S structure are presented. These agree with the theoretical predictions and show that significant gain factors are attainable. A qualitative discussion of the high-frequency characteristics is presented which predicts that detection of light at microwave frequencies by a S-M-S device is possible. THEORY In this discussion, the photocurrent, iT, measured across terminals attached to the semiconductor emitter and collector layers is related to the current pho-toemitted from the metal base layer. The latter will be referred to as the primary photocurrent. The behavior of the primary photocurrent is determined by the characteristics of the two metal-semiconductor diodes. The diode photoemission is illustrated in Fig. 1, which shows the emitter and collector potential barriers. The metal thickness has been greatly exaggerated. As will be discussed later, the actual barrier shape can be much more complex, but this diagram illustrates the essential features of the photoemission process. An absorbed photon having an energy greater than the barrier height can emit an electron into the emitter or collector. Since this process is discussed

Jan 1, 1968

By G. S. Rice

The subject of dust explosions in coad mines first appears in the Transactions of this Institute following the first great mine disaster that happened in…

Jan 1, 1915

By C. G. Bieber, R. F. Decker

The effects of minor constituents on the malleability of nickel alloys are described. These effects are related to the atomic diameter, valence, and position on the Periodic Table. The basic methods for removal or neutralization of deleterious elements are then reviewed. Finally, practical methods for melting nickel alloys are described in detail and related to minor constituent control. L HE first malleable nickel was produced by Fleit-man in about 1870 by the addition of manganese and magnesium to the molten metal to counteract the harmful effects of sulfur. Merica and Waltenbergl explained the mechanism by which these elements accomplished the desired result. They showed that sulfur in concentrations in excess of about 0.005 pct produced films of a brittle low melting eutectic of nickel-nickel sulfide which completely surrounded the grains. When manganese was added to molten nickel it reacted with the sulfur to form manganese sulfide which precipitated as widely scattered globules in the grain boundaries. The further addition of small amounts of magnesium converted the sulfur to a very stable sulfide of magnesium which was relatively insoluble in both the liauid and solid states and therefore occurred as finely divided particles within the grains where it had relatively little detrimental effect upon the malleability of nickel or its alloys. The practice of treating nickel with manganese and magnesium came to be called "deoxidation" and was employed without appreciable modification for the commercial production of wrought nickel and high nickel alloys (in this paper—50 pct or more nickel) until about 1930 even though the results were never entirely satisfactory. At that time a more extensive study was made of the effects of minor constituents on malleability and metallurgical quality. The results, small portions of which have been published,2-4 are presented here with other pertinent data. EFFECTS OF MINOR CONSTITUENTS UPON NICKEL Systematic additions were made of 0.5 pct or less of each of most of the elements of the periodic ta- ble. It was established in this study that some minor constituents other than manganese and magnesium were extremely influential. The malleability, as evaluated by the reduction of area in tension tests, depended roughly on temperature as shown in Fig. 1. Four temperature zones are of interest; the cold malleable zone (up to about 1000° F), the red short zone from roughly 1000° to 1500' F, the hot malleable zone around 2000° F and the incipient melting zone. Most of the malleability problems are associated with the red short zone and the discussion will concern this mainly. The reduction of area in normal tensile tests on high-purity nickel (see curve A of Fig. 1) appeared to have no

Jan 1, 1962

By Robert P. Burrows

In preparing this paper the object has been to set forth facts relating to illumination problems, which, judging from the results realized in the iron and steel and other industries somewhat similar to mining, will tend toward furthering safety, production, and contentment of employees, as well as economy of operation in mines. By applying the principles of illumination with the assistance of modern appliances, the full benefits in efficiency may be derived from improvements already made in other details of mine operation. The lighting of a typical coal mine may be*divided into four distinct parts: 1, The lighting of the buildings about the top; 2, the lighting of the working faces; 3, general illumination at the bottom; and 4, special applications of lighting. The lighting of buildings about the top may be treated in the same manner as that of any other industrial plant, for we have a boiler room, an engine and generator room, a forge, a machine shop, and a hoist room. These can be well and efficiently lighted by the use of 100-watt tungsten-filament multiple lamps with proper reflectors so spaced and suspended that a power consumption of from ¼ watt per square foot in the boiler room to 1 watt per square foot in the machine shop is obtained. The methods that apply to this kind of lighting have been ably treated by a number of authors,' and for this reason a detailed discussion is unnecessary. The lighting of the working faces is usually done by means of portable lamps, of which there are four types in use: The oil torch, the acetylene Iamp, and the oil and the electric safety lamps. The different types have been fully described in numerous papers and articles and will not be covered here, although a few figures on the cost of operation will no doubt be

Jan 1, 1916

By David E. Nicholas

INTRODUCTION In this paper, a numerical process for selecting a mining method, with the emphasis on underground mass mining techniques, such as caving, induced caving, and stoping, is proposed. In the past, selection of a mining method for a new property was based primarily on operating experience at similar type deposits and on methods already in use in the district of the deposit. Then, the chosen method was modified during the early years of mining as ground conditions and ore character were bet- ter understood. Today, however, the large capital investment required to open a new mine or change an existing mining system make it imperative that the mining methods examined during the feasibility studies and the method actually selected have a high probability of attaining the projected production rates. Although experience and engineering judgment still provide major input into the selection of a mining method, subtle differences in the characteristics of each deposit, which may affect the method chosen or the mine design, can usually be perceived only through analysis of measured characteristics. The parameters that must be examined when choosing a mining method include: 1) geometry and grade distribution of the deposit; 2) rock mass strength for the ore zone, the hanging wall, and the footwall; 3) mining costs and capitalization requirements; 4) mining rate; 5) type and availability of labor; 6) environmental concerns; and 7) other site-specific considerations. This paper encompasses a detailed look at the first two parameters since they, plus mining costs, have the greatest impact on the selection of a mining method. The proposed method selection process is for a project where drilling has defined sufficient geologic reserves, but little or no underground development has been done. Since each deposit has its own characteristic geanetry/grade distribution, and rock mechanics properties, mining method selection should be at least a two-stage process. In Stage 1, the deposit is described in terms of geometry, grade distribution, and rock mechanics properties. Using these parameters, the mining methods can be ranked to determine which are most applicable; they can then be considered in general terms of mining and capitalization cost, mining rate, type and availability of personnel, environmental concerns, and other site-specific considerations. In Stage 2, the most likely mining methods are costed out, based on a general mine plan. Mining and capitalization costs are used to determine a cut-off grade fran which a minable reserve can be calculated; economic comparisons can then be made to determine the optimum mining method and economic feasibility. During the mine planning phase of Stage 2, rock mechanics information would be used to provide realistic estimates of underground opening size, amount of support, orientation of openings, and caving characteristics, and open pit slope angles. If ground control or operational problems should be encountered with the methods being considered, modifications could be made. Although planning on paper extends start-up time, it is cheaper to err on paper than to find the error after mining has begun. METHOD SELECTION - STAGE 1 The main purpose of Stage 1 is to select those mining methods which should be considered in greater detail. The simplest way to do this is by defining those characteristics required for each mining method and then determining whether the characteristics of the deposit are suitable. However, no one mining method is so restrictive that it can be used for only one set of characteristics, as indicated by the classification system proposed by Boshkov and Wright (1973). In the mining method selection proposed, geometry, grade distribution, and rock mechanics characteristics are ranked according to their acceptability for ten general mining methods.

Jan 1, 1981

By H. M. Chance

(Butte Meeting, August, 1913.) ADEQUATE treatment of the difficulties surrounding the valuation of mineral lands requires that agreement be first reached defining value as understood for the purpose of appraisal. To define value as the price of a product is not sufficient, and does not assist us in using the factors that cause variations in values and in relative values. The real value of any product depends primarily upon its relation to the necessities, comforts and pleasures of mankind. As the necessities, comforts and pleasures of the civilized races differ from those of more primitive man, the value of products varies with the degree of civilization and the environment of the consumer. Coal has no value to the savages of warm climates, and arrow-head flint none to the residents of New York. It has long been recognized that what has been termed ? intrinsic value " must be limited to materials that are essential to existence-air, water, food. But "intrinsic value" cannot be measured in monetary terms. The intrinsic value of a bushel of wheat is due to the fact that it will support the life of an individual for a certain definite time, but this fact does not enable us to measure or to express that value in monetary terms. It has often been proposed to adopt as a measure of the value of any product the quantity of labor necessary to produce it, but this method is of limited application, and will not apply to what may be termed "intrinsic values." For many reasons it might be well, while assenting to the fact that any material may he intrinsically valuable, to abandon the use of the term " intrinsic value." One of these reasons is the tendency to confuse the idea of intrinsic value with a value that is conferred by economic conditions, that is purely artificial and that may be permanent or evanescent; Intrinsic value must from its nature be permanent and unchangeable.

Jan 7, 1913

By A. D. Hodges

The great mining region of Peru is a mountainous belt of country, running nearly the whole length of the republic, and comprising the two grand ranges of the Andes with the elevated table-lands between them. On the east of this belt are the extensive plains and fertile valleys of the Amazon and its tributaries. On the west is a narrow strip of coast 20 to 50 miles wide, for the most part a sandy desert, but producing abundant crops where irrigated ; and here are found petroleum (Department of Piura), salt (at Huacho and elsewhere), nitrate of soda in enormous amounts at the south, silver in a few localities (Province of Tarapaca), copper and other mineral products. The Western Cordillera, running nearly parallel with the shoreline, rises like a wall on the eastern side of the coast-belt, with passes from 15,000 to 18,000 feet high and peaks attaining 18,000 to 20,000 feet. Further east, at a varying distance, is the Eastern Cordillera, composed of broken mountain ranges which, considered as one group, have a general parallelism with the western chain, but individually vary greatly in direction, sometimes running nearly east and west, in places projecting out into the Amazonian lands, or here and there curving around to unite with the western ridge, and with this enclosing immense inter-alpine plains. These general features are indicated in Fig. 1. The surface of these plains is uneven and traversed by lower ranges of hills which surround large lakes, or rolling pampas, or fertile valleys; and through many of these last run rivers of considerable size. The whole country has a high altitude (averaging up to 15,000 or 16,000 feet), and slopes gradually north and east towards the Amazon, into which drain all its waters. Its bounding mountain chains are scored on all sides by narrow, picturesque and pre-

Jan 1, 1888

By Jos D. Weeks

On the extreme fringe of' the great Appalachian coal-basin is a long narrow detached coal-field, which is, in some respects, one of the most important in the United States. This field, about 90 miles long by 2½ to 16 miles wide, extends from the southwest corner of Somerset county, Pennsylvania, through Allegany and Garrett counties, Maryland, Mineral, Grant and Tucker counties, West Virginia, into Randolph county, West Virginia. In this distance four distinct sub-districts are recognized, the Wellersburg in Pennsylvania, the Cumberland-Georges creek in Maryland, and the Elk Garden and the Upper Potomac in West Virginia. The output of coal from the whole field including steam, domestic, smithing and coking-coal of the best quality, is about 4,500,000 tons annually. It is the nearest to tide-water of all the bituminous coal-fields which supply the great coal-markets of the Northern Atlantic seaboard ;

Jan 1, 1895

By S. A. Montague

Mica can claim a considerably greater importance than would be assumed from its comparatively small dollar volume, which came to about $37,000,000 for the United States industry as a whole in 1957. Mica is one of the strategic minerals. We must depend on imports from distant sources for virtually all of our requirements of high grade block and all of our mica splittings. Mica is essential and indispensable for vacuum tubes and high-performance condensers, two electronic components which are vital military necessities besides being nearly indispensable to civilization today. Composition and Properties Mica is the general name for a group of some nine different minerals, two of which, muscovite and phlogopite, are the minerals used by the mica industry as its raw material. Several of the other varieties are commercially useful-vermiculite, * used for heat insulation in expanded form, and lepidolite, used as an ore of lithium while the others-biotite, roscoelite lepidomelane, paragonite and zinnwaldite have little or no commercial importance. Biotite frequently occurs as an undesirable impurity in muscovite. Table 1 lists various properties and other data concerning muscovite and phlogopite. Chemically, mica is a complex silicate of sodium, potassium and aluminum. Most varieties of muscovite are higher in sodium, and of phlogopite in magnesium. There are no important uses of mica where the chemical analysis is important, except that in some uses of ground mica, the content of iron oxide present as an impurity must be kept to a very low limit. Muscovite occurs in a range of color from the so-called India "ruby" which is more closely a pinkish brown, to light and dark green, with numerous other intermediate shades. Ruby color is usually preferred by industry, especially in the better qualities. When split very thin the color in most [ ] micas disappears. Muscovite mica is frequently found containing black and red "stain" as a homogeneous part of the books or sheets. In most cases this stain or impurity is magnetite

Jan 1, 1960

By Earle E. Schumacher, W. C. Ellis, John F. Eckel

Copper-calcium alloys are of interest as materials for use in deoxidized conductors of high conductivity. That calcium is effective in deoxidizing and degasifying copper is well known. Brandenberg and Wiensl have described the use of calcium in the casting of sound copper and state that the deoxidation can be carried out without difficulty. The castings that they prepared were sound and sufficiently ductile to permit wire drawing. Pratt,2 in British Patent No. 1699 (1907), has claimed the use of calcium for the deoxidation and degasification of copper. Masing3

Jan 1, 1930

By Paul M. Tyler

MINOR industrial minerals included in this chapter are: the alum minerals, bromine, calcium chloride, epsomite and other natural magnesium salts, iodine, meerschaum, quartz, industrial crystals other than quartz (Iceland spar, tourmaline, fluorite, selenite, mica), and nonfuel gases (air, helium, carbon dioxide). ALUM MINERALS The alums comprise a series of double sulphates (or selenates) isomorphous with potash alum, which, according to a ruling of the Pennsylvania courts, is the only product commercially described simply as "alum." Common alum occurs in nature as kalinite (K2SO4- A12 (SO4) 324H2O). The mineral mendozite (Na2S04) 3.A12 (SO4)3- 24H2O) is soda alum; tschennigite (NH4)2SO4.Al2 (SO4)3.24H2O) is ammonium alum; and there are about a dozen other native alums and related double sulphates. Alunite (alumstone or alum rock) has the formula Al2(SO4) 3.K2S04.4A1 (OH)3 and alunogen, Al2(So4) 3.18H20. Saline residues, found wherever natural water is evaporated, may contain sulphate of alumina, which for most uses is the essential ingredient of alum. Mineral wells and springs that emerge from beds of pyritiferous shale are typically astringent and at times form local deposits of alum, generally as incrustations. Acid waters acting upon aluminous rocks may form sulphates of alumina. The alums of commerce, as well as aluminum sulphate (concentrated alum), are produced principally by treating bauxite with acid, but they have been made also on a substantial scale from clay, cryolite, pyritic slates, schists, lignites, alunite, and leucite. Alum shale-chiefly clay, pyrite, and (usually) carbonaceous matter-was extensively used in England as a source of alum for more than two centuries. In France, pyritic lignites mixed with sand and clay were burned in heaps to red ash, the leach Liquors from which, after treatment with ammonia, yielded alum and copperas. Processes have been developed for making alum or aluminum sulphate from such diverse materials as feldspar, aluminous phosphate minerals, greensand, and mixtures of mica and

Jan 1, 1949