Search Documents

By I. E. Campbell, R. I. Jaffe

Oxygen, nitrogen, and hydrogen are known to be absorbed by titanium at elevated temperatures. Ehrlichl reports that about 30 at. pct oxygen can be dissolved in solid solution by alpha-titanium. Nitrogen also has a solid solubility in alpha-titanium, but there is no information as to its extent. The solid solubility of hydrogen in titanium also is high. Kirshfeld and Sieverts2 report 50 at. pct soluble, while Hägg3 reports about 33 at. pct hydrogen to be soluble in alpha-titanium. General statements are made in the literature that oxygen, nitrogen, and hydrogen embrittle titanium, but no quantitative measurements have been made of the effect of these gases on the mechanical properties of the metal. One reason for this is the lack of a source of titanium pure enough to be considered a suitable starting material. Iodide-refined titanium, made by thermal decomposition of titanium iodide vapor on an incandescent wire,4 contains small amounts of carbon, silicon, iron, and aluminum, but is very low in oxygen, nitrogen, and hydrogen content, and, therefore, was used in this work. A further reason for the lack of quantitative information on the effect of these gases, particularly oxygen, is the difficulty of carrying out accurate analytical determinations at the low concentrations of interest in this work. For this reason, the oxygen, nitrogen, and hydrogen were added in measured amounts as gases, and diffused into the titanium, to avoid the necessity of chemical analysis. The purpose of the work reported here was to isolate and measure the effects of oxygen, nitrogen, and hydrogen on titanium of the highest purity available at the time. The concentrations studied were 0.25, 0.5, and 1 at. pct in each case. Experimental Work One-half of a 24-in. hairpin of iodide-refined titanium was available for this work. The rod was approximately 0.25-in. in diam and had a 0.003-in.tung sten core. From chemical and spectro-graphic analyses, the purity of the sample was estimated to be between 99.80 and 99.95 wt pct. The chief impurities (aside from the tungsten core) were iron (0.04 pct), silicon (0.01-0.1 pct), aluminum (0.05 pct), carbon (0.03 pct). The tungsten core constituted 0.05 pct by weight of the sample. Although some alloying undoubtedly took place between the tungsten and the titanium during the deposition reaction, the core remained substantially intact in the deposited metal. The initial average hardness of the titanium as deposited was 105 Vickers (10-kg load). The maximum hardness was 116 Vickers and the minimum 91 Vickers. The metal was somewhat harder than that currently being obtained by the iodide process, that is, 75-90 Vickers. The rod was cold swaged to ¼-in. diam and then cold rolled in diamond shaped rolls to about 0.080-in. square, using reductions of 15 pct in area per pass. The 0.080-in.-square wire was cut into 6-in. lengths for the preparation of the alloys by the gaseous absorption and diffusion method. ADDITION OF OXYGEN, NITROGEN, AND HYDROGEN TO TITANIUM A modified Sieverts' absorption apparatus, shown in Fig 1, was used in

Jan 1, 1950

By W. M. Courtis

. There seems to be a well-established belief that there is an indescribable something in the appearance of gold-quartz not to be learned from books, that enables those who are fortunate enough to have acquired the power to recognize this characteristic, to pronounce at once that a certain quartz will or will not pay. The stronger this claim is made, the more certain is the claimant to be one of the self-styled practical miners. After several years spent among the gold-mines of California with practical and professional gold-miners, I have come to the conclusion that very few care to risk an opinion on a piece of quartz until some of it has been "horned out." Nevertheless, there is what the miners call a " kindly " appearance, that is more often followed by good results than is a vitreous, water-wet-looking quartz. A dark, resinous quartz seems to be most in favor, but there are so many exceptions that even quartz as " white as a hound's tooth " produces gold in some mines.. The ribbon-quartz, a laminated variety, separated by thin talc or chlorite partings, has a well-known good name. The slides of rich quartz specimens show that this parallelism is a microscopical characteristic of the only macroscopical distinction that, as a rule, these quartzes show. This is shown by Nos. 12 and 13, photographs of the richest quartz, that averaged $65 per pound. It is noticeable, also, in Nos. 7 and 9, and others. Dr. Hensoldt, of Columbia College, who prepared, excellently, a large number of my slides, and whom I have to thank for descriptions and suggestions, says of Nos. 12 and 13: "This variety of quartz differs considerably, microscopically, from the others of your locality, and is, in more than one respect, remarkable. Like the

Jan 1, 1890

By Emil Gathmann

Steel as it is poured, or teemed, into the mold for forming the ingot may be broadly separated into two divisions; i.e., effervescing or gassy steel, also termed evolution steel, and non-effervescing or killed steel, also termed solution steel. Between these primary divisions there are various types having the characteristics of both divisions but really nut belonging to either; such steels are termed semi-piping, rising, or wild, as the type may be. True effervescing steel should contain large volumes of gases, which are evolved while the metal is being teemed from the ladle nozzle into the mold, and continue to escape while the temperature of the steel is falling prior to its solidification the top of the ingot remaining liquid, due to the evolution of gases, until an ingot skin of considerable thickness has been formed. These gases consist principally of hydrogen, carbon monoxide, nitrogen, and ammonia. It is generally understood that nitrogen gases are the first evolved and these form the skin blowliolcs, troublesome at times, in the solidifying ingot. Ingots made of effervescing steel will always contain a large number of blowholes. Such blowholes are not deemed objectionable in certain products if they occur well inside the ingot where they will not be subjcct to oxidation upon cooling, reheating, and rolling or forging of the ingot. Very little top or bottom discard is taken from this type of ingot, as pipes, or large shrinkage cavities, at the upper portion of the ingot do not usually occur, the difference in volume between the liquid and the solid steel (6 to 10 per cent.) being compensated by the innumerable blowholes distributed throughout the body of the ingot. Of the 40,000,000 tons of steel made in the United States during the year 1919, at least 35,000,000 tons of ingots were made of gassy or semi-gassy steel. Killed, or solution, steel is termed true piping steel from the characteristic pipe or shrinkage cavity that usually occurs in the uppermost central portion of the ingot.

Jan 1, 1922

By C. W. Hall

Owing to its isolation and comparatively small tonnage, the Yoquivo district is not widely known; though financially important and, geologically, quite interesting. San Francisco dc Yoquivo, the center of the mining district, is in the western part of the state of Chihuahua, Mexico; about 35 miles west of. San Juanito, on the Kansas City, Mexico & Orient R. R. The town can be reached from the railroad by a good trail over a rugged country. The elevation of Yoquivo is 6500 ft., and peaks surrounding the town are 2000 ft. higher. The mining towns of Concheno and Ocampo are 25 miles northwest, and Uruachic is 20 miles southwest. The climate, temperate and healthful, is almost ideal. The rainy season begins in July and ends the latter part of September. There is usually, though not always, some precipitation in all months except April, May, and June: The mountains are covered with pine and scrub oak. Water, wood and lumber are plentiful for all ordinary purposes, and hydroelectric power is available for. about six months of the year, when wood for steam, power is utilized as an expedient. The district has been worked: recurrently for over 60 years. The Yoquivo province lies on the steep western-slope of the Tara-humara division of the Sierra Madre range of mountains. The province is traversed by many deep canyons, most of which flow west. The town is situated on the San Francisco arroyo, which makes a confluence with the Huevachic stream 212 m. southwest; the Huevachic in turn joins the Candemeña river farther down and these two drain the western flank of the Tarahumara mountains and form the headwaters of the Mayo river. The claims of the Yoquivo Development Co., which, is the only organization in the district with a record of any considerable production,: lie within an area roughly 112 m. square. The area extends from the, San Francisco arroyo north, and from the Dolores arroyo west, and is confined to the andesitc formation.

Jan 2, 1926

By Emil Gathmann

Steel as it is poured, or teemed, into the mold for forming the ingot may be broadly separated into two divisions; i.e., effervescing or gassy steel, also termed evolution steel, and non-effervescing or killed steel, also termed solution steel. Between these primary divisions there are various types having the characteristics of both divisions but really nut belonging to either; such steels are termed semi-piping, rising, or wild, as the type may be. True effervescing steel should contain large volumes of gases, which are evolved while the metal is being teemed from the ladle nozzle into the mold, and continue to escape while the temperature of the steel is falling prior to its solidification the top of the ingot remaining liquid, due to the evolution of gases, until an ingot skin of considerable thickness has been formed. These gases consist principally of hydrogen, carbon monoxide, nitrogen, and ammonia. It is generally understood that nitrogen gases are the first evolved and these form the skin blowliolcs, troublesome at times, in the solidifying ingot. Ingots made of effervescing steel will always contain a large number of blowholes. Such blowholes are not deemed objectionable in certain products if they occur well inside the ingot where they will not be subjcct to oxidation upon cooling, reheating, and rolling or forging of the ingot. Very little top or bottom discard is taken from this type of ingot, as pipes, or large shrinkage cavities, at the upper portion of the ingot do not usually occur, the difference in volume between the liquid and the solid steel (6 to 10 per cent.) being compensated by the innumerable blowholes distributed throughout the body of the ingot. Of the 40,000,000 tons of steel made in the United States during the year 1919, at least 35,000,000 tons of ingots were made of gassy or semi-gassy steel. Killed, or solution, steel is termed true piping steel from the characteristic pipe or shrinkage cavity that usually occurs in the uppermost central portion of the ingot.

Jan 1, 1922

By A. K. Burton

This paper reviews transportation trends in large base metal open-pit mines in recent years. Particular attention is paid to the unprecedented increases in the cost of oil and its effect on operating costs. Fuel conservation and measures to improve trucking efficiency are considered. The paper also discusses viable alternatives for reducing or eliminating the use of trucks. Various advantages and disadvantages of using conveyors to transport shot rock from the mine are reviewed. The paper concludes with some observations on current policies and trends primarily aimed at mitigating the high cost of energy.

Jan 1, 1983

By Morris Cohen

WITHIN the past two years, a number of publications have called attention to the double peaks, or stages, that appear in the hardness and strength curves of certain aging alloys. The author has shown the existence of double hardness peaks during the aging of a high-purity silver-copper alloy;' and on the basis of electrical resistance, microscopic, dilation and lattice-parameter measurements, he concluded that the initial hardness peak occurs prior to precipitation while the secondary hardening is due to precipitation. It was suggested that the general mechanism of age-hardening involves two consecutive processes, the first consisting of nucleus or knot' formation, and the second consisting of actual precipitation and particle growth. It was further held that the two stages are interdependent, but because of nonuniform precipitation they may overlap each other to an extent that increases as the aging temperature is raised. At high aging temperatures, the effect of the first stage cannot be detected because of the rapid occurrence of precipitation. . The general theory of age-hardening recently presented by Dr. M. L. V. Gayler3 is in close agreement with the picture outlined above. With reference to work done on duralumin, copper-beryllium and copper-silver alloys, Dr. Gayler also concluded that age-hardening takes place in two consecutive steps: first, diffusion (in which the solute atoms migrate to certain crystallographic planes), and then precipitation. However, W. L. Fink and D. W. Smith4 have shown that the double aging peaks that appear in the strength curves of high-purity aluminum-copper alloys may be explained without recourse to pre-precipitation phenomena. By means of very careful metallographic technique, Fink and Smith demonstrated that during aging the precipitation takes place at an accelerated rate along the grain boundaries and slip planes as a result of the plastic deformation caused by the drastic quench from the solution heat-treatment temperature. † The general precipitation occurs at a

Jan 1, 1938

By G. D. Van Ardsdale, A. W. Hudson

Heap leaching, as practiced at Rio Tinto, Spain, while one of the oldest, and probably one of the cheapest, methods of extracting copper from its ores, has not had, until recently, other than experimental application in this country. This has been due partly to a mistaken idea that the Rio Tinto ores possess some obscure and mysterious quality that renders them alone suitable to the process, partly to the fact that tests properly made meant the expenditure of large sums of money and several years time, and partly to the fact that favorable commercial and other conditions are not often found. This paper gives some views on the chemistry and mechanism of the method, an account of the preliminary experiments, and the final plans adopted for a large-scale installation of the method by the Phelps Dodge Corpn. for treating low-grade ore from Sacramento Hill, Bisbee. If results comparable with those obtained from the test heap are to be had from the large plant, this plant will operate on the lowest-grade sulfide ore now being treated commercially in the country. The method has several advantages: The installation cost is low. Interest charges must, of course, be made both on the cost of the ore delivered to the plant and for the plant itself, but as these are low, there is considerable advantage in the ability to regulate output by more or less complete shutdowns in accordance with market and other conditions. The amount of labor needed is small, and the cement copper produced may be considered nearer a finished product than the sulfide concentrates from a mill, and certainly means less installation cost per ton to put into final form by present methods. At Bisbee, conditions were favorable for a trial of the method for, in the preparation of the Sacramento Hill orebody for steam shoveling,' a large amount of material below concentrating grade had to be moved to

Jan 1, 1923

By J. F. Myers, F. M. Lewis

THE selection of the proper type of flotation machine involves the consideration of a wide variety of factors. Under any condition, all types of machines will promote some kind of separation. Obviously, the correct way of deciding which type of machine is best suited for a particular problem would be to set up all types of machines and test them out in a competitive manner, but the vast number of small concentrating plants are unable to make such complete and exhaustive tests. The experience of the authors of this paper indicates that if all the factors involved in any particular problem can be determined, and if all the flotation-machine characteristics are understood, some basis for selection could be arrived at other than actual comparison. This paper is presented to show how the process factors and machine characteristics have been combined at the mills of the Tennessee Copper Co. from studies of several types of flotation machines. At the two mills of the Tennessee Copper Co. in the Ducktown Basin of Tennessee, four distinct flotation separations are made on the complex sulphide ore. Three different concentrates are produced from the ore-in the order of their importance: iron concentrate, copper concentrate, and zinc concentrate. Four different types of flotation machines are used. The selection of these four machines, for the plant operation, was based upon the study and operating experience of the machine units shown in the following list: Fagergren machine; square cell, size 56 inches Fagergren machine; level type, size 56 inches Denver machine; conical disk impeller, size 24 inches Denver machine; receded disk impeller, size 24 inches Minerals Separation Sub-A, size 24 inches Munro-Pearce deep cell, pneumatic Southwestern air machine, Hunt principle To date the study of flotation machines has been confined almost entirely to the rougher circuits. The various cleaning operations, being relatively a much simpler matter, have not been investigated so thoroughly. Table 1 shows a typical analysis of the two ores as well as of the mineral content. []

Jan 1, 1944

By A. W. Hudson, G. D. Van Ardsdale

Heap leaching, as practiced at Rio Tinto, Spain, while one of the oldest, and probably one of the cheapest, methods of extracting copper from its ores, has not had, until recently, other than experimental application in this country. This has been due partly to a mistaken idea that the Rio Tinto ores possess some obscure and mysterious quality that renders them alone suitable to the process, partly to the fact that tests properly made meant the expenditure of large sums of money and several years time, and partly to the fact that favorable commercial and other conditions are not often found. This paper gives some views on the chemistry and mechanism of the method, an account of the preliminary experiments, and the final plans adopted for a large-scale installation of the method by the Phelps Dodge Corpn. for treating low-grade ore from Sacramento Hill, Bisbee. If results comparable with those obtained from the test heap are to be had from the large plant, this plant will operate on the lowest-grade sulfide ore now being treated commercially in the country. The method has several advantages: The installation cost is low. Interest charges must, of course, be made both on the cost of the ore delivered to the plant and for the plant itself, but as these are low, there is considerable advantage in the ability to regulate output by more or less complete shutdowns in accordance with market and other conditions. The amount of labor needed is small, and the cement copper produced may be considered nearer a finished product than the sulfide concentrates from a mill, and certainly means less installation cost per ton to put into final form by present methods. At Bisbee, conditions were favorable for a trial of the method for, in the preparation of the Sacramento Hill orebody for steam shoveling,' a large amount of material below concentrating grade had to be moved to

Jan 1, 1923

By J. A. Danko, C. D. Pears, L. D. Schmidt, J. P. McGee

This paper describes a pilot plant built on the campus of West Virginia University by the Federal Bureau of Mines station at Morgantown, West Virginia, for gasifying pulverized coal in a mixture of oxygen and steam at pressures in the gasifier up to 450 psig. The work upon which this report is based was done under a cooperative agreement between the Bureau of Mines and the West Virginia University. The goal of Bureau of Mines work at Morgantown is development of a low-cost process for producing mixtures of carbon monoxide and hydrogen for the modified Fischer-Tropsch synthetic-fuel plants, which may be shifted to produce hydrogen for coal-hydrogenation plants. Gasification with oxygen offers the inducement that the gas may be generated at the pressure at which the gas will be utilized in a gas-synthesis plant. Since the optimum pressure for the synthesis appears to be about 400 psig, the gas should be produced at approximately 450 psig to take care of pressure drops in the purification train and control valves. If the gas is generated at the pressure of utilization, only the oxygen need be compressed, not the raw synthesis gas. This means a saving in power of 5 hp per hour per 1000 cu ft (CO + H2), which is approximately a saving of 4 cents per gallon of gasoline. For example, consider a commercial plant generating 18,000,000 standard cubic feet per hour of raw gas that would produce approximately 10,000bbl of liquid product per stream-day. Assume that this gas would be 85 pd CO + H2 and that the oxygen required would be 320 cu ft per 1000 cu ft of CO + H2. The following estimate is based on a commercial centrifugal compressor. If the 18,000,000 std cu ft per hour of synthesis gas is compressed to 450 psig with 74 pd efficiency, 107,000 hp is required for compression. If the synthesis gas is generated at 450 psig pressure, only

Jan 1, 1953

By W. A. Hoyer

A pulsed high-energy neturon-induced spectral logging tool has been built and field-tested. The reaction of deuterium on tritium is used to generate pulses of 14-Mev neutrons. By detecting only the prompt gamma rays produced by neutron inelastic reactions in the formation, the presence and relative abundance of carbon, oxygen, calcium, silicon and other important elements may be ascertained from a gamma-ray spectrum. Gamma-ray spectra obtained in a shallow test well and in experimental field use show that it is possible to identify formations and their contained fluids. INTRODUCTION The penetrating gamma rays from naturally occurring radioactive elements in subsurface formations have been used for a number of years in well logging as a means of characterizing and distinguishing strata. Still another nuclear logging method which has been employed for some years consists of the bombardment of strata with neutrons and the measurement of the number of gamma rays produced by neutron capture reactions involving elements in subsurface strata.' Since one of the principal elements entering into capture reactions is hydrogen, the latter procedure essentially results in a hydrogen log, whether the hydrogen be in combined form in either oil or water; thus, the log gives an indirect measure of porosity. These methods, with various refinements, have been developed to such an extent that they have become routine procedures in formation evaluation. Neither gamma-ray logging nor conventional neutron logging, however, yields sufficient information to permit unequivocal identification of the mineralogic composition of formations, and neither method gives information which may be used for the positive identification of hydrocarbons in strata. Accordingly, a number of efforts have been made in recent years to gain additional information from nuclear logs. Brannon and Osoba have shown that it is possible to identify naturally occurring radioactive elements in subsurface formations by spectral analysis of gamma rays emanating from these elements. Such an identification is of value in the characterization of strata. A simplified form of spectral analysis of gamma radiation resulting from neutron capture reactions between elements in earth materials and bombarding neutrons has been used with some suc- cess under favorable conditions to differentiate between petroleum and water. This method relies upon the relatively high energy of gamma radiation from neutron capture by chlorine and, in effect, furnishes a chlorine log. In areas in which interstitial water is of sufficiently high salinity, this log can give valuable information on water saturation and, thus, indirectly on hydrocarbon saturation. Still another approach to obtaining more information by nuclear techniques is "activation logging", in which certain elements yield short-lived radioactive isotopes on neutron activation and, thus, can be detected by gamma-ray spectral analysis. From the standpoint of determining by nuclear logging methods the mineralogic composition of strata and the presence or absence of hydrocarbons, it is essential that information be obtained on the presence and relative amounts of several elements such as carbon, oxygen, hydrogen, calcium, silica and others. Some elements, such as hydrogen, chlorine and sulfur, can be determined by spectral analysis of gamma radiation resulting from neutron capture reactions."" Others — carbon and oxygen, for example — do not enter readily into capture reactions but do yield gamma rays of characteristic energies from inelastic scattering reactions with high-energy neutrons. Accordingly, the latter reactions are of particular interest as a means of identifying hydrocarbons in subsurface strata. Several years ago it was recognized that information requisite to the identification of subsurface strata and of contained fluids could be obtained by pulsed operation of a subsurface neutron generator and associated gamma-ray detector. It was contemplated that pulsed operation would be effective in discriminating in time that gamma radiation which results predominantly from inelastic scattering reactions from that gamma radiation arising from neutron capture reactions. Accordingly, research was continued and construction of such a device was initiated. Although many problems were encountered, they were solved successfully. The following sections describe the tool which has evolved, its performance and the results which have been obtained with it to date. THEORY OF OPERATION OF NEUTRON-INDUCED GAMMA-RAY SPECTRAL LOGGING TOOL THEORY OF INDUCED NUCLEAR REACTIONS Of fundamental importance is the fact that an element, when bombarded with neutrons, emits gamma radiation of energy characteristic of that element. In theory, therefore, an element may be identified by

By W. D. Lowry

As most of the industrial activity of Oregon is centered in the Portland area, the foundries there consume the bulk of the foundry sand produced in Oregon. Although a number of the larger towns scattered throughout the state have gray-iron foundries, the sand used by most of them is of local origin: The yearly consumption of foundry sand of all types for the past few war years in Oregon is estimated to have been approximately 40,000 tons valued at about $285,000, of which an estimated 18,000 tons was shipped in from the Ottawa, Ill., district for use largely by the steel foundries. Until 1945 much of the silica sand consumed by the steel foundries in the Pacific Northwest, approximately 50,000 tons in 1944, came from Ottawa, Ill. and surrounding regions. Although some silica sand was shipped in from Belgium in the past, none is known to have been imported in recent years. Early in 1945, a very promising high-grade silica sand being produced near Eugene, Oregon, was introduced, and all but two of the Portland steel foundries are using this new sand. Until a few years ago, the search for good local (Oregon) foundry sands was carried on largely by the foundry supply houses. Recently the Oregon Department of Geology and Mineral Industries has investigated a number of deposits and has carried on and fostered research on the most promising deposit near Eugene, about 120 miles south of Portland. High-grade silica foundry sand from this deposit is now being marketed in Oregon, Washington, and British Columbia. The Eugene sand is one of the very few outstanding western steel-foundry sands. Field investigations by the Oregon Department show that there are relatively few deposits of sand in Oregon suitable for foundry use. A knowledge of the geology of the state makes this readily understandable. The only major primary sources of the quartz present in sandstones in Oregon are the intrusive masses of granite, granodiorite, and quartz diorite of late Jurassic or early Cretaceous age found in the Siskiyou Mountains of southwestetn Oregon, a part of the old Klamath Mountain highland, and in the Blue Mountains of northeastern Oregon. Transportation militates against the development of any possible deposits of foundry sand found east of the Cascade Mountains in central and eastern Oregon because few railroads traverse that area. East of the Cascades, which separate western from eastern Oregon, many of the older sediments of Paleozoic and Mesozoic age have either been metamorphosed or contain much volcanic eruptive material, and even if some of the Mesozoic sediments are highly quartzose in places, they are in relatively inaccessible areas. All the Tertiary sediments there are of continental origin and contain much ash and other volcanic debris, for there was great volcanic activity during much of that period. In western Oregon much the same is true of the Paleozoic and Mesozoic rocks

Jan 1, 1947

By O. Jantti, Erkki Laurila, R. T. Hukki

INVESTIGATION of the methods of analyses for magnetite and ilmenite in the Otanmaki iron-titanium ore and respective mill products has resulted in certain improvements in the methods conventionally employed. The outcome of the investigations is summarized as follows: 1—Development of a diamond-drill core analyser for the determination of magnetic susceptibility of drill cores containing magnetic minerals. 2—Development of a magnetite-ilmenite analyser for pulverized products. 3—Development of a potentiometric method of chemical analysis for the determination of iron, vanadium, and titanium in succeeding steps from one test sample. 4—Proposal for a continuous and automatic magnetite assay method. Diamond-Drill Core Analyser The conventional method of assaying diamond-drill cores consists of splitting the cores, pulverizing them and running chemical analyses on representative samples. The physical properties of magnetic minerals, however, offer an entirely different approach to obtain similar final result by the measurement of respective magnetic susceptibilities in a properly designed instrument. This instrument is shown in Fig. 1. Essentially it consists of a magnetic unit, A, and of a meter unit, B. On top of A is a slot where a piece of diamond-drill core C is visible. The magnitude of disturbance in the original magnetic field caused by the magnetic minerals in the drill core can be observed from the microammeter. This reading is a function of the combined susceptibilities of all magnetic grains in the magnetic field. The magnetic unit is built of E-sheets of a shell transformer, as shown in Fig. 2. The primary coil and two identical secondary coils are wound around the central leg and end legs, respectively. The drill core under examination is placed into one of the air gaps as shown in Fig. 2. The number of ampere-turns of primary coil excited by 50 or 60-cycle ac give a maximum induction of about 600 gauss in the air gaps. The secondary coils are connected in series in the opposite direction. Thus their voltages compensate each other if no drill core exists in the air gap or if the susceptibility of the drill core is equal to zero. As soon as the susceptibility becomes greater than zero, the balance of the magnetic circuit is disturbed, resulting in increased voltage in the terminals of coil 1 and in a respective decrease of voltage in the terminals of coil 2. The voltage difference thus produced is a function of the effective susceptibility of the drill core. If the magnetic grains in the drill core are unevenly distributed, the voltage difference varies as the core is rotated around its own axis. The voltage difference is measured with a Bren-tan0 tube voltmeter. If extreme sensitiveness is desired, the established symmetry of the magnetic circuit does not allow reduction of the 0-voltage difference far enough. Therefore a compensatory voltage of a correct phase taken from the terminals

Jan 1, 1952

Prof. G. W. MAYNARD, New York City (communication to the Secretary): Prof. Christy, in his admirable paper on "The Growth of American Mining Schools," has overlooked the work done by the Rensselaer Polytechnic Institute in its department of mining and metallurgy. This oversight is naturally due to the fact that the department was, for lack of money, discontinued in 1871. It was organized by the writer in 1867, starting with ten students, who had already completed the first two years of the civil engineering course in the Institute. The course covered two years, specifically devoted to mining, metallurgy and assaying, which, in connection with the two years' drill in the civil engineering department made a four years' course. During the four years of the existence of the department, thirty-five students took the course, of whom twentyfive graduated; and of this number eight have been members of the Institute of Mining Engineers, and the majority of them have occupied high positions in the profession. The equipment of the department was, at that time, second only to that of the Columbia School of Mines. As Prof. Christy has cited other institutions which are not distinctively mining schools, but in which the ruining course was subordinate to other courses, it seems to me that the work in this line carried out by the oldest engineering school in the country may very properly be referred to. In addition to the regular mining course, a special course in assaying was given; and many young men were here prepared for positions in the mines and metallurgical works of the west. PROF. George F. Swain, Boston, Mass.: I have listened with great interest to Prof. Christy's valuable paper, but there is one conclusion at which he arrives that appears to me entirely unjustifiable, and to which I desire to take exception. Prof. Christy finds that of the total wage-earners in the United States in 1880,10.41 per cent. were employed in " trade and transport;" 20.24 per cent. in " manufactures and mechanics," and 1.83

Jan 1, 1894

By T. G. Chapman

The writer has carried on experimental work for several years with respect to the simultaneous dissolution of gold by cyanide and the adsorption of the dissolved gold on activated charcoal in ore pulps, followed by the recovery of the charcoal by flotation. The results of this experimental work have been sufficiently encouraging to suggest a new process based on the principle of simultaneous dissolution and adsorption of gold, applicable to certain ores and tailings that cannot be treated to advantage by countercurrent decantation or filtration. Applications for patents have been filed and The Dorr Company, Inc. has the exclusive right to license the use of the process. The purpose of this paper is to describe such a process, state its possible advantages and immediate field, and give some results obtained on a laboratory scale. Early Experimental Work In the early stages of the experimental work attempts were made to precipitate soluble gold from cyanide solutions with zinc and aluminum in ore pulps followed by flotation of the precipitated gold, but since the results were not promising enough to continue with these precipitants attention was directed to carbon. The first experiments with carbon comprised the addition of cyanide and alkali to the ore pulp, the addition of carbon at or near the end of the dissolving period, and the recovery of the carbon by flotation. With this method of procedure the assumption was made that carbon functioned as a precipitant of gold from cyanide solutions and as such should be added as are other precipitants, including zinc and aluminum; namely, at the end of the dissolution period. The assumption was then made that carbon functioned as an adsorbent, and that if such assumption proved to be correct, it could be added with success to the ore pulp at the time of adding the cyanide. The first experiment along this line was successful in that the feasibility of the dissolution of gold by cyanide and the simultaneous extraction of the dissolved gold by carbon in ore pulps was demonstrated, at least with respect to such treatment on a laboratory scale.

Jan 1, 1939

By T. G. Chapman

The writer has carried on experimental work for several years with respect to the simultaneous dissolution of gold by cyanide and the adsorption of the dissolved gold on activated charcoal in ore pulps, followed by the recovery of the charcoal by flotation. The results of this experimental work have been sufficiently encouraging to suggest a new process based on the principle of simultaneous dissolution and adsorption of gold, applicable to certain ores and tailings that cannot be treated to advantage by countercurrent decantation or filtration. Applications for patents have been filed and The Dorr Company, Inc. has the exclusive right to license the use of the process. The purpose of this paper is to describe such a process, state its possible advantages and immediate field, and give some results obtained on a laboratory scale. Early Experimental Work In the early stages of the experimental work attempts were made to precipitate soluble gold from cyanide solutions with zinc and aluminum in ore pulps followed by flotation of the precipitated gold, but since the results were not promising enough to continue with these precipitants attention was directed to carbon. The first experiments with carbon comprised the addition of cyanide and alkali to the ore pulp, the addition of carbon at or near the end of the dissolving period, and the recovery of the carbon by flotation. With this method of procedure the assumption was made that carbon functioned as a precipitant of gold from cyanide solutions and as such should be added as are other precipitants, including zinc and aluminum; namely, at the end of the dissolution period. The assumption was then made that carbon functioned as an adsorbent, and that if such assumption proved to be correct, it could be added with success to the ore pulp at the time of adding the cyanide. The first experiment along this line was successful in that the feasibility of the dissolution of gold by cyanide and the simultaneous extraction of the dissolved gold by carbon in ore pulps was demonstrated, at least with respect to such treatment on a laboratory scale.

Jan 1, 1939

By E. V. Potter, H. C. Lukens

INTRODUCTION IN general, during all electrowinning processes, large volumes of gas are liberated at the cathodes of the electrolytic cells. Most of this gas escapes from the electrolyte, but much of it may be absorbed or entrapped in the metal being plated. In many cases, this is not objectionable, but since it is liberated when the metal is heated, it is a potential source of trouble where the metal has to be heated or melted. Since this gas is principally hydrogen, in escaping from a melt it may cause minor explosions and scattering of the molten metal, while in other cases it has been reported to make the metal rise in the molds when cast. Therefore such metals would be more generally useful if all or most of the gas were removed before they were used. In an earlier investigation' the gas content of electrolytic manganese was determined and methods found for removing most of it without detrimentally affecting the properties of the metal. In this paper results of a similar investigation on electrolytic chromium are presented. APPARATUS The apparatus used in these investigations is essentially the same as that used in the manganese work' and is shown in Fig I. It consists of sample chamber A, vacuum or pressure gauge B, volume gauge C, vacuum pump D, hydrogen container E, auxiliary gas chamber F, and furnace G. The pressure in the system is measured by the mercury manometer B. Changes in ' gas volume are measured by volume gauge C which is essentially another mercury manometer in which . the volume of the mercury column is large and can be varied by raising or lowering the well H. In this apparatus the tube had a volume of 100 cc for a 61 cm length. Larger changes in gas volume can be accommodated by auxiliary containers attached to the system at F. The sample is heated by furnace G, the temperature of which is regulated within ± 5°C by an automatic controller. The only change in the apparatus was the sample container which was made smaller because of the chromium metal's containing more gas than the manganese metal and a smaller sample was used. METHOD The measurements were made as follows: The complete system when cold was evacuated and refilled with H2 until all the air was removed. It was then refilled with H2 to the desired pressure, as indicated on manometer B. The temperature was then raised to the desired value and as gas was either liberated from or absorbed by the sample, the height of well H was changed to alter the volume of the system so as to keep the pressure constant. In determining rates of liberation of gas, volume readings were taken at convenient time intervals depending on the rapidity with which the gas was liberated. In determining total volumes, the specimen was held at constant temperature and pressure until

Jan 1, 1948

By Thomas E. Garnar

Zirconium and hafnium are curious elements because they are almost always found together in nature. Zirconium was discovered by Klaproth in 1789 and isolated 35 years later by Berzelius. Because hafnium's chemical properties are so close to those of zirconium, it was not discovered until 1923 when Coster and Von-Heresey detected it using x-ray spectrographic analysis. These elements occur most commonly in nature as the mineral zircon (ZrSiO4) and less commonly as the oxide baddeleyite (ZrO2). They also are found as a variety of other silicates. Zircon was identified as a component in alluvial and beach sands in 1895, but it was not produced in any quantity until 20 years later. Zircon is always a coproduct from TiO2 mining and processing. During World War I it was produced as a coproduct of beach sand mining for titanium minerals just south of Jacksonville Beach, FL, and was patented as a refractory. It was not until the 1930s when Zircon Rutile, Ltd. began mining at Byron Bay on the east coast of Australia that zircon was first used as a foundry sand. Later in the 1940s, NL Industries, Humphreys Gold Corp., and E. I. du Pont de Nemours & Co., Inc. began production of zircon sands from fossil beaches in northeast and northcentral Florida. Baddeleyite first became available as a commercial product in 1916, but never in the quantity of zircon. Zircon holds a unique position as an industrial mineral because it is used for both its physical and chemical properties as well as an ore of zirconium and hafnium metals. Australia is the major zircon producer followed by South Africa and the US. Zircon is also produced in India, Sierra Leone, Sri Lanka, Malaysia, China, Thailand, and Brazil. Undeveloped heavy mineral beach sand reserves containing zircon are known to occur in Egypt, Malawi, Senegal, and Tanzania. Locations are shown in Fig. 1. Mineralogy Zirconium and hafnium are always present together in naturally occurring compounds. Most commonly they form as the silicate sometimes containing iron, calcium, sodium, manganese, and other elements. Less commonly they are found as oxides in combination with titanium, thorium, calcium, and iron. Zircon is the most common form. It is extremely resistant to weathering, therefore, often it is present in ancient beach sands and placer deposits. Although resistant to alteration from external sources, it is vulnerable to internal alteration as the result of thorium and uranium substituting for zirconium either in the zircon lattice or in solid solution. Alteration to the metamict state takes place as radioactive emanations from these elements disorder the crystal lattice, accompanied by hydration, reduction in specific gravity, and changes in color. The mineralogy of zircon and baddeleyite and variation of physical and chemical properties are shown in Table 1. The effects of zircon's internal alteration and darkened color can be corrected by heating to 1000°C for 30 min or so. A certain time-temperature relationship makes it possible for decolorization and reordering of the crystal lattice to take place when heating at higher temperatures for shorter periods or at lower temperatures for longer periods. After heating, x-ray diffraction patterns are sharper, the grains may be harder, and except for particles of malacon, the grains will be white or colorless in the absence of grain surface coatings. The color change is only temporary and the particles slowly darken with time. Zircon fluoresces light yellow in shortwave ultraviolet light. If exposed to ultraviolet light for extended periods of time, white (calcined) zircon turns purple. With time the induced color begins to fade and eventually disappears (e.g., calcined Florida zircon exposed to ultraviolet light for 24 hr still retains faint, but discernible, purple color after six months).

Jan 1, 1983

By J. V. N. Dorr

THE Elko Prince mine is in the Gold Circle district, Nevada, about ½ miles(2. 4km.) from the town of Midas, 55 miles (88.5 km.) west of Battle Mountain and 50 miles (8.5 km.) northeast of Golconda. The district is described by Emmons in U. S. Geological Survey Bulletin 408, 1910. Little was said of the Elko Prince, however, as only a small amount of work had then been completed. The geological structure of the region is simple. The oldest exposed formation, covering most of the area, is rhyolite, which has a light-colored devitrified groundmass enclosing phenocrysts of feldspar, quartz, and magnetite. It has been somewhat weathered and partially stained with oxide of iron. There are several outcrops of andesite which cut the rhyolite. The ore deposits occur as fissure veins, replacement veins, and sheeted zones. The Elko Prince vein is of the first type. The rhyolite near the veins is silicified, stained with oxide of iron, and, at some localities, replaced by ore, or is so permeated by metals as to be classed as ore. The vein filling consists chiefly of quartz, and the values consist entirely of gold and silver. Part of the gold exists as the native metal and part is associated with pyrite. Silver occurs free and its argentite in handed streaks through the vein. These veins trend in a northwesterly direction, with dips varying from 65° to vertical.

Jan 8, 1918