Search Documents

By W. TRINKS

RAPID progress has been made in the automatic control of open-hearth furnaces in the past few years and many firms today\supply such control apparatus. It is somewhat surprising that so little was heard about open-hearth control up to about, 1928, and that thereafter the practice of automatically controlling open-hearth furnaces spread very rapidly. Before discussing the reasons for this it may be advisable to list the quantities that can be controlled. One of the easiest quantities to be controlled in the open-hearth furnace is pressure. The reasons for controlling it are plain. If there is excess pressure in the furnace, products of combustion leak out around .the .door and through all the cracks in the brick-work. The stability of the piers between the doors is seriously endangered, and front wall repairs become frequent. Furthermore, hot gases are lost that might be usefully employed in heating the checkerwork. If there is a slight vacuum in the furnace, cold air entering through the doors and cracks cools the interior, slowing down the reactions and making it impossible to secure the highest degree of preheat from the checkerwork.

Jan 1, 1931

By Wayne Loel

THE application of aerial photographs to all phases of geologic mapping is set forth, indicating the advantages to be gained in different types of country and under varying climatic conditions, Methods of field and office procedure are given from a geological point of view, as well as suggestions regarding the best methods of aerial mapping for different uses and under varying field conditions, including the study of submarine geology. Aerial photographs with accompanying geologic maps are shown to illus-trate the appearance from the air of different geologic features under varying climatic and topographic conditions.

Jan 1, 1938

By William R. Chedsey

ALTHOUGH few changes can be reported in educational methods at the mineral technology schools during 1940, other events have taken place of direct interest to, and that will have a profound effect upon, mineral industry education on the United States. In the erection of new buildings, some notable changes have been made on the campus, The U.S. Bureau of Mines Experiment Station at the University of Utah, Salt Lake City, was dedicated on May 20. The construction and equipment of this building cost between $300,000 and $400,000. It will be the general headquarters for the metallurgical division of the Bureau and will have a pronounced effect upon the mineral industries research program at the University.

Jan 1, 1941

By H. B. FERNALD

THE first year to which the Revenue Act of 1936 has applied is now passed. It is appropriate to try to give some calm thought to the plan of Federal income taxation as now imposed and what it will mean to the business and industry of the country if this plan of taxation is continued unchanged. Whether or not we like to pay these taxes is beside the point. Taxes are high and may be expected to be high for many years. The important question is whether the taxes to be imposed will destroy or injure business enterprise and development, and, in so doing, lower the standards of employment, living, comfort, and welfare of our people. The power to tax is the power to destroy. That destruction may come suddenly as a cyclone, or slowly as dry rot. What, if any, features are there in the present plan of Federal income taxation that have these destructive tendencies? A few of the points follow that seem to call for consideration.

Jan 1, 1937

By Leo F. Reinartz

Part II of a four-part series on the history of steelmaking in the US, points out the inadequate safety and living conditions that existed in steel mills at the turn of the Century. Also defined are furnace and process developments. OPERATIONS in steel plants today are highly mechanized. Men work in light, clean, orderly melting shops, making it difficult for old timers to convince young men that primitive, hazardous conditions existed in steel plants at the turn of the century. Working conditions then were very poor as compared to present day standards. In small plants especially, sanitary, locker, and washroom facilities, first-aid practices and stations were un- known Accidents were frequent and severe. Workers had a fatalistic attitude toward getting hurt. He who had an accident was looked upon as a hero. A dirty bandanna often served as a bandage. Infections were frequent. Electric cranes were in their infancy and broke down often Cables had not as yet replaced chains. Pig iron and scrap iron were loaded by hand in the stockyard, and stockyard locomotives were un- known; mules served as the usual motive power. It was not unusual to see recorded a delay of ½ hr in charging a furnace because of a balky mule. Furnace operations A few plants had primitive charging machines, but most furnaces were charged by placing scrap or pig iron on the paddle of a long peel, which rested on a bar across the furnace door opening. Laborers at the handle end of the peel, using the bar as a fulcrum, would heave the material into the furnace by a down and sideward motion of the peel handle. In time they became expert in placing these materials in the furnace, but it was hard, hot work, and a long time was required for charging. Cold charges of 25 tons required more than 12 hr for melting and re- fining the steel. Ports, doors, and frames were not water cooled. The charging and working area in front of the furnace was covered with steel plates. They were hot and often warped by the intense heat of the un- insulated checker chambers directly below. In the summer, working conditions on the charging floor were almost unbearable. Silica refractories were of poor quality. Because of this, and the inadequate training of furnace men in fuel control and furnace operations, roofs, front and back walls, and ends burned out rapidly. Dolomite machines were unknown; consequently, furnace banks and hearths were fettled with dolomite by the use of hand shovels. The round system required six or more men. Each man took a shovelful of dolomite and, in his turn, deposited it on the back wall and bank by a dexterous forward swing and twist of the shovel. The upward swing of the shovel partially protected his face from the searing heat of the furnace coming out through the wide-open door. Considerable skill and stamina were required to do this job properly. Reverse valves, usually of the cast-iron butterfly type, were located below the charging floor. They were operated by long levers on the charging floor level men they became warped, because of heat and abuse, great strength and skill were required to reverse them. Furnace operations were difficult. The quality and quantity of producer gas coming from irregularly stoked, hand-operated gas producers was uncertain and unreliable. Furnace Linings and ports were quickly burned out. Poor bottom and side-wall refractories, indifferent and inexperienced crews, as well as irregular re-

Jan 1, 1961

By Arthur Phillips, E. S. Davenport

The purpose of this paper is to present certain data and observations resulting from a series of experiments dealing with the heat treatment and microstructure of commercial white cast iron and its derivative, malleable iron. In planning the experimental work, particular pains were taken to secure for the tests white cast iron of "normal" composition; i.e., within the composition limits commonly prescribed by manufacturers of malleable castings. A review of the literature leads us to believe that much data of a fragmentary character treating of the graphitization of white cast iron have been of little value, mainly because of the diversity in chemical composition of the materials employed in the tests. Moreovcr, when feasible, annealing periods at least comparable to those of current practice have been adopted. We wish to acknowledge our indebtedness to the members of the research department of the Eastern Malleable Iron Co. for the white cast iron used in the test's and, particularly, for their active cooperation during the experimental stage of the work. In this paper the following subjects will be discussed in the order indicated: Data on the thermal critical points of white cast iron and malleable iron. Changes produced in tensile properties and microstrue.-ture of white cast iron by annealing at different temperatures within the, range, 760 to 1100° C. Relation of thickness of wall section of hard iron to microstructure and tensile properties of malleable iron obtained under normal annealing conditions. Notes on mechanics of graphitization of normal white cast iron as observed in specimens quenched after various periods of anneal at approximately 800" C.

Jan 1, 1922

By Arthur Phillips, E. S. Davenport

The purpose of this paper is to present certain data and observations resulting from a series of experiments dealing with the heat treatment and microstructure of commercial white cast iron and its derivative, malleable iron. In planning the experimental work, particular pains were taken to secure for the tests white cast iron of "normal" composition; i.e., within the composition limits commonly prescribed by manufacturers of malleable castings. A review of the literature leads us to believe that much data of a fragmentary character treating of the graphitization of white cast iron have been of little value, mainly because of the diversity in chemical composition of the materials employed in the tests. Moreovcr, when feasible, annealing periods at least comparable to those of current practice have been adopted. We wish to acknowledge our indebtedness to the members of the research department of the Eastern Malleable Iron Co. for the white cast iron used in the test's and, particularly, for their active cooperation during the experimental stage of the work. In this paper the following subjects will be discussed in the order indicated: Data on the thermal critical points of white cast iron and malleable iron. Changes produced in tensile properties and microstrue.-ture of white cast iron by annealing at different temperatures within the, range, 760 to 1100° C. Relation of thickness of wall section of hard iron to microstructure and tensile properties of malleable iron obtained under normal annealing conditions. Notes on mechanics of graphitization of normal white cast iron as observed in specimens quenched after various periods of anneal at approximately 800" C.

Jan 1, 1922

By R. I. Jaffee, F. C. Holden, H. R. Ogden

Ti-Mn alloys were studied in order to determine the factors affecting the mechanical properties of &stabilized titanium alloys. The principal compositional factors have been found to be solid-solution strengthening, the martensitic transformation, and instability of the P phase. Structural factors, such as grain size and shape, were found to have more influence on ductility and toughness than on strength. THE alloys of titanium with the &stabilizing elements offer the chief hope for developing useful heat treatments. Conversely, the heat-treatment response possible with the p-stabilizing elements causes difficulties such as weld embrittlement and thermal instability during service at elevated temperature. Therefore, it is of considerable technical importance to understand the factors that govern the heat-treatment responses in these alloys, so as to be able to soften the alloys if they are embrittled by an adventitious heat treatment, to render them stable in service, or to harden them while maintaining adequate ductility and toughness. The Ti-Mn system is a good example with which to demonstrate the factors that govern strength and heat-treatment response in. a P-stabilized system. The region of the a-j3 transformation, after the work of Maykuth, Ogden, and Jaffee,' is shown in Fig. 1. The a solubilities are low. This means that, in the two-phase a-p field, partition of manganese between the two phases occurs practically only to the P phase. The solid-solution effects are therefore chiefly the result of solution in the ,8 phase. The eutectoid occurs at 20 pct Mn and 550°C, and proceeds very sluggishly. It can be ignored in heat treatments in hypo-eutectoid alloys, except for long-time storage at low temperatures below the eutectoid temperature. Even here, there is some question that diffusion proceeds far enough to involve eutectoid decomposition. Three compositional factors bear on the mechanical properties and structure of titanium a-P alloys. These are: 1—solid-solution strengthening, 2—mar-tensite transformation, and 3—P instability. Combined with the purely structural factors of grain size and shape, these govern the properties of the alloys. Perhaps the most important factor is solid-solution strengthening. The facts that manganese dissolves in a titanium to a maximum of only 0.5 pct and most of the manganese partitions to the p phase dominate the structure and properties of the a-/3 alloys. Because of the overwhelming preference of manganese for the ,3 phase, the P phase is harder and the a phase is softer. The relative amounts of both phases may be modified by heat treatment in the a-P field as application of the lever rule in the two-phase field clearly shows. A critical temperature in the Ti-Mn diagram is 800°C. This is the P transus temperature of the 6.4 pct Mn alloy, which has the lowest manganese content which will form all retained-P phase on quenching to room temperature. Any quench performed from below 800°C will produce a structure consisting of only a, a plus retained P, or retained p, for alloys of the compositions used in this work. For alloys containing less than 6.4 pct Mn, any quench from above 800°C will always result in structures

Jan 1, 1955

By WILLIAM BOWIE

THE development of the isostatic idea during the last century would make an interesting paper in itself. But the various steps in the development have been covered in a number of papers and books which are readily available. Therefore this short paper should not give space to. the historical phases of the subject. Isostasy is really an old idea, but it is only in the last few decades that it has taken on any great prominence or importance in the study of earth phenomena. It is really remarkable how closely Dutton' sensed the isostatic principle 40 years or more ago. His general principles of isostasy as outlined by him have stood the test of time and fit in closely with the general ideas held today. It would seem, however, that some of his views with regard to the application of isostasy to geological processes must be modified or abandoned.

Jan 1, 1930

By A. B. Kinzel

IT is with sincere appreciation and a deep sense of responsibility that I accept the honor of delivering the Howe Memorial Lecture. In our time metallurgical research has delved into phenomena ever more complex in character, so that much of this work must be done by organized teams. We, of the Union Carbide and Carbon Research Laboratories and the Electro Metallurgical Co., are truly a team and the lecture which is to follow is due largely to a few of the outstanding members of that team here cited and well known to you in their own right: John Lamont, whose work deserves special recognition, Walter Crafts, William Forgeng, William Binder, Robert Fowler, and David Swan. Thus it is a fitting pleasure to accept this honor for the research institution which I represent. Henry Marion Howe was truly inspirational and his breadth of view was such that he could use either the method of rigid proof or implied mechanism to further the broad understanding. But perhaps his outstanding characteristic was his sound judgment and his ability to weigh observations. The following is replete with observations and judgment as to their implication. We would like to feel that it is the type of dissertation which Howe, himself, would have enjoyed. Chromium carbides in stainless steel have, in a sense, been a key to the progress of the stainless steel industry. Brearley's first stainless steel, containing approximately 0.30 pct C, was successful because it differed from previous Fe-Cr alloys in that the carbides were present in such amount and form as to provide the stainless and cutting properties. Again, the 12 pct Cr die steels with a carbon content of 1.5 pct or more achieved their properties by virtue of the form and distribution of the chromium carbides. In the straight chromium steels with from 12 to 25 pct Cr, chromium carbide amount and distribution are once more the determinants with respect to physical properties and corrosion resistance. In each of the cases just cited the role of the carbide is in essence similar to that of iron carbide in carbon steel and this story is so well known that we need not dwell on it. In the austenitic stainless steels, the chromium carbide plays only a minor positive role with respect to mechanical properties, and for corrosion resistance the objective is to achieve maximum homogeneity. Thus the tendency has been to ever lower the carbon and correlatively the chromium carbide content of the austenitic steels. Today stainless steels with carbon less than 0.03 pct are beginning to find their true place, and this is being aided in major degree by our Company's introduction of a new type of ferrochromium having negligible carbon. The role of carbon in these austenitic steels has long been recognized, and a truly enormous amount of research has been devoted to the subject. Much has been learned about corrosion resistance, but the attack on the problem from the point of view of carbide precipitation and the nature thereof has left much to be understood. Because of its fundamental importance to the future of stainless steels, further study of the mechanism of carbide formation in austenitic steels is of interest. In the 18-8 Cr-Ni steels, which are typical of the austenitic class of steel, carbon is soluble in the aus-tenite to the extent of approximately 0.15 pct at 1832°F (1000°C). The solubility becomes less with decreasing temperature, so that at 1652°F (900°C) the solubility limit is approximately 0.06 pct, at 1472°F (800°C) it is about 0.03 pct, and at 932°F (500°C) it is approximately 0.01 pct. Obviously this is the ideal situation for the classical precipitation phenomenon. It is true that, in a sense, 18-8 austenite resulting from annealing is in a metastable state, and the phenomenon of ferritic precipitation from this austenite should be considered. However, in a so-called fully austenitic 18-8 steel this is secondary with respect to the carbides and can be neglected. A wide variety of chromium carbides is known. Only one chromium carbide, Cr,,C,,, frequently referred to as Cr,C, has been found in unmodified low carbon 18-8 steel. This, fortunately, simplifies the study of the precipitation phenomena. For this study an A.I.S.I. type 304 stainless steel of commercial quality was selected. Analysis showed C 0.07 pct, Mn 0.49 pct, Si 0.33 pct, Ni 9.34 pct, Cr 18.91 pct, and N 0.033 pct. As expected with this composition the steel was homogeneous after annealing except for a few pools of ferrite, which were disregarded in that their location was not coincident with subsequent carbide precipitation areas. On corrosion testing the steel was normal and typical of good commercial quality. Specimens 1/2xlx4 in. were annealed and subjected to precipitation heat treatment for 100 hr at 100" temperature intervals from 1000° to 1500°F and for ten selected intervals ranging from 5 min to 64 hr at 1300°F. These blocks were then cut into small pieces for metallographic studies. The first problem

Jan 1, 1953

By Edward H. Robie

PONCA CITY proved an ideal selection as a place of meeting for the Petroleum Division this fall. The accommodations at the Conoco Club were just what was required for such a gathering; the committee having the arrangements in charge functioned with the efficiency of veterans and the enthusiasm of neophytes; and the members and guests followed the speakers with close attention, entered the subsequent discussions with gusto, and divulged the "low-down" at private conferences. No one minded the drizzling rain on the first day, which only served to keep up the attendance in the auditorium; the weather then cleared up in time for a group picture before the gathering went their separate ways.

Jan 1, 1932

Adams, John H., Pres. & Mgr., Alabama Lime & Stone Corpn., 1302-4-8 First Ave., Birmingham, Ala. '14 Adams, L. W., Otis Steel Co., Riverside Plant Cleveland, Ohio. '15 Adams, Leland D., Min. Engr., Mgr., Signal Mines Co., Goldbanks Quicksilver Co., 485 California St., San Francisco, Cal. '14 Adams, R. L., Min. Engr., Old Ben Coal Corpn., Mine 12 Christopher, III. `19 Adams, Robert M., Robert M. Adams Co 1201 Fidelity Bldg., Duluth, Minn. '20

Jan 1, 1925

By W. H. Class

The embrittling effects of oxygen, ozone, nitrogen, air, and surface residues, on NaCl has been investigated. The embrittlement by ozone and oxygen was found to be associated with the formation of a NaClO3 surface compound. In these cases the initial crack that was responsible for fracture (in a bend test) always nucleated at the corners between the tension and side faces. The behavior of air was very erratic and on certain days did not produce enzbrittlement. During these periods, crystals that had become embrittled by the ozone treatment completely recovered their ductility after a short exposure to the ambient atmosphere, It was established many years ago1 that considerable ductility could be obtained in NaCl single-crystal specimens if the crystal surfaces were dissolved in water either during or immediately prior to the test. The original interpretation of this effect by Joffe attributed the enhanced ductility to the removal of surface microcracks by dissolution. Later investigations2'3 have suggested that the exclusion of air from the specimen surface is the criterion for extensive plastic flow prior to fracture. The air em-brittlement in this later work was attributed to the diffusion of gaseous atoms into the surface layers of the crystal, thereby impeding the movement of dislocations. This model satisfactorily accounts for the reembrittlement observed after further air exposure subsequent to the water dissolution treatment. However, the situation has recently become more complex by the observations in several laboratories4-t that under certain conditions air exposure does not impair the ductility of NaC1. It has also been recognized5 that improper drying operations after water dissolution can leave surface precipitates that lead to embrittlement. Cleavage defects on as-cleaved crystals can often be another source of embrittlement. In the present work the effect of the gaseous atmospheres nitrogen, argon, air, oxygen, and ozone, on the ductility of rock salt was studied extensively. The embrittlement resulting from oxygen and ozone exposures was found to be associated with the formation of a NaC1O3 surface film. It is suggested that certain atmospheres, one of which often can be ambient air, which inhibit the formation or favor the decomposition of this compound, can promote ductility. Thus one aspect of the Joffe effect is certainly related to the removal of surface compounds or complexes by water dissolution. The effect of surface precipitates that remain after drying operations and of cleavage defects were also studied. In neither of the latter cases was the embrittlement as severe as that found with a NaClO3 surface layer. PROCEDURE AND SPECIMEN PREPARATION The nature of the embrittlement produced by the agents mentioned above was studied by means of microscopy, mechanical testing, and X-ray diffraction. Specimens were cleaved from large crystals of optical quality sodium chloride obtained from the Harshaw Chemical Co., and, except for those tested in the as-cleaved condition, were given a 15- to 20-sec immersion in distilled water followed by a rinse in absolute methyl alcohol. The specimens were then blotted on a soft, absorbent paper, and dried by a few seconds exposure to a stream of warm, dry air. Such a procedure was found to give a control surface which was microscopically free of residues. (A few crystals were intentionally painted with a concentrated NaCl solution in order to investigate the effect of surface residues). All specimens were of 0.140 sq in. cross-section. Crystals prepared in the above manner were immediately placed in a gas train where they could be exposed to the desired gases for preselected periods of time. For the oxygen and nitrogen exposures, pure reagent-grade gases were employed. The ozone was provided in the form of an ozone-oxygen mixture (approximately 10 pct ozone) prepared by passing commercial grade oxygen over a strong ultraviolet light source. All gases were dried prior to their introduction into the train. Since argon was found to be completely inert in its behavior (i.e., residue-free specimens that were exposed to argon were not embrittled), it was periodically utilized to check the control specimen surfaces as well as the condition of the gas train used for aging the specimens. After exposure to the gaseous media in question, the crystals to be used for the measurement of the strain to fracture were transferred from the gas train to a protective oil bath (without further exposure to the atmosphere) where the tests were conducted in three-point bending. The apparatus was so adjusted that the load could be applied at a constant, continuous rate. Other Snecimens from the gas train were deformed

Jan 1, 1962

By M. R. Lorenz

Efficient visible light emission from p-n junctions in semiconductors is currently achieved in the four materials, Sic, GaP, ]Ga1-xAs and GaAs1-x,. Recent advances in materials preparation and p-n junction formation are briefly reviewed. The radiative recombination processes in the different materials depend largely on the band structure and the impurity states of each material. The spectral distribution of the emission ranges from the blue in Sic, to green in Gap, yellow in Sic and red in Gap, Ga1-x AlxAs and GaAs1-x Px. The origin of the various processes are discussed. The conversion of the electrical power into optical power and the measurement of the conversion efficiency are reviewed. The currently maximum quantum efficiencies at 300°K are: 3 pct in GaP(red), 1 pct in SiC(yellow), 0.1 pct in GaP(green), 0.2 pct in Ga1-x AlxAs at 66001, and 0.1 pct in GaAs1-x Px at 6800. The brightness and the interplay of the quantum efficiency and the luminous efficiency are given detailed consideration. VISIBLE light generated by the application of a direct current to a semiconductor crystal was first observed by Lossev1 in 1923. Light emission came from naturally occurring junctions in Sic crystals but little was known then with regard to the mechanism of charge transport and light emission. Some nearly 30 years later and with a vastly increased understanding of semiconductors the phenomenon of electroluminescence was studied in more detail, for example in p-n junctions of germanium.2 In these early studies, the efficiency of converting the electron current into a photon current was very low and therefore aroused little interest toward practical application. More recently it became apparent that in certain materials, for instance GaAs, and under certain conditions, the conversion efficiency was not low at all.3 The subsequent discovery of the p-n junction laser4-6 provided the impetus for increased studies of electroluminescence. Light emitted from GaAs occurs in the infrared region of the electromagnetic spectrum and is not visible to the eye. At nearly the same time the use of GaAs1-xPx led to laser action at low temperatures which was visible to the eye.7 Later a red light emitting diode, made from Gap, was reportedS which emitted incoherent radiation at 300°K with an external quantum efficiency of about 1.5 pct. The fact that such efficient devices were obtainable led to a more concentrated effort in the search for highly efficient room-temperature semiconductor light sources. It is some of this later work on p-n junction luminescence with which we will be concerned here. Since our aim is centered on visible light, with hv =1.8 ev ( ?=7000?), only the wider band gap semiconductors are of interest, i.e., Eg 1 1.8 ev. Although many compounds meet this criterion, only a limited number of those are also good semiconductors, i.e. contain low resistance n and p regions. Some of the more promising candidates are listed in Table I. We will only be concerned with light generation from a p-n junction. This limitation excludes essentially the group II-VI binary compounds, although we will briefly review the case of ZnTe and the solid solution ZnTe1-xSex. As we will show they may contain a p-n junction but only of a special kind. Most of the discussion will deal with the four materials, Sic, Gap, Gal-xAlxAs, and GaAs1-xPx. These appear to be at the present time the best visible light emitting semiconductors. In the following sections we will briefly consider: 1) the electrical properties of p-n junctions; 2) some recent advances in materials preparation; 3) the formation of p-n junctions; and then in somewhat greater detail we will consider: 4) the various radiative recombination processes; 5) the measurement and observation of the external quantum efficiency; 6) the luminous efficiency; 7) the brightness of light emitting diodes (LED'S). THE P-N JUNCTION The p-n junction in a semiconductor crystal is the interface between two differently doped regions. More specifically the p region is doped predominantly with acceptor impurities and the n region contains predominantly donor impurities. The energy band structure of a degenerate p-n junction at thermal equilibrium is shown in Fig. l(a). The excess electrons on the n side of the junction are confined to this region by the barrier potential Eg. Similarly the excess holes on the p-side of the junction are confined to the p-region by a similar potential barrier. If we now apply a dc voltage V such that the p region is made positive and the n region negative, the barrier potential EB is reduced by the applied voltage, V and the junction is said to be forward biased. With the barrier potential lowered, electrons and holes can drift toward the p region and n region, respectively, see Fig. l(b). The current voltage characteristics of p-n junctions in most wide band gap materials can be described by the relation: J = Joexp(eV/BkT) [1] where the functional form of Jo is determined by the recombination mechanism. Jo is generally a complicated parameter which depends on a number of different factors including temperature, junction width, bias voltage, and carrier lifetimes. The parameter B also depends on the recombination mechanism but

Jan 1, 1970

By Charles E. Wait

The old laboratory at the School of Mines was among the notoriously bad ones, being situated in apartments of the main collegebuildings not originally intended, and conspicuously unfit, for the use to which they were put; while, as in many of our schools and colleges, the assaying was done in the basement of the college. Prominent among the disadvantages of such an arrangement are insufficient light, poor ventilation, and little or no provision to carry off offensive gases. It is not my intention now to present a complete description of this building. I wish merely to call attention to a few points in its construction and equipment, which may prove of interest to those who contemplate erecting buildings for snch work, and who may be, as we were in this instance, limited as to funds. In this laboratory every room is well lighted; all rooms used by students are well ventilated, and are provided with closed hoods for

Jan 1, 1887

By E. W. Engelmann

RAPID progress has been made during the past year in the copper mills throughout the country. Particular efforts have been made to increase the fine-grinding efficiency by the installation of larger classifying units operating in closed circuit with ball mills, such as the 78-in. high-weir Akins installation at the Phelps Dodge plant at Ajo, Ariz.; also the Type "FX" Dorr classifiers of Nevada Consolidated at McGill. Nev. and the "FX" Dorr bowl classifier of the Braden Copper Co. in Chile. Some of the copper milling plants in the Southwest, such as Chino in New Mexico and Ray Con. in Arizona, have replaced rolls operating wet in their fine-grinding circuit by rod mills. At Hollinger primary rod mills were formerly used in open circuit followed by pebble mills in closed circuit with classifiers. They now have primary ball mills in closed circuit with large extra heavy classifiers and no secondary mills. This new installation is producing the same grinding on 5000 tons per day with a reduction in cost of nearly 4c. per ton. At the Braden plant, in Chile, short-head Symons crushers have replaced 54-in. rolls, thereby in- creasing crushing capacity with some saving in maintenance cost.

Jan 1, 1939

The following list contains the names of members whose death notices have been printed in MINING AND METALLURGY from March 15, 1947 through March 15, 1948 Biographical sketches published in MINING AND METALLURGY are indicated in the last two columns Year of Election - Name - Date of Death - Issue Containing Biography - Page 1938 ABERNATHY, G E , (M) Feb 6, 1948 April 1948 266 1935 ARCHER, M T, (M) Oct 26, 1947 Dec 1947 633 1947 ATIKINSON, JAMES E, (S) Feb 6, 1948 June 1947 309 1940 AYRES, VINCENT L, (M) Oct 14, 1947 Jan 1948 59 1915 BABCOCK, JAMES E , (M) April 1, 1947 June 1947 309 1942 BAGGALEY, WILLIAM BLAIR, (A) Aug 28, 1947 Jan 1948 59 1897 BUIN, II POSTER, (M) Mar 9, 1948 April 1948 219 1945 BAMPFIELD, A E (M) Unknown Mar 1948 215

Jan 1, 1952

J. E. Johnson, Jr., Glen Wilton, Va. (communication to the Secretary*):—Mr. Meissner announces early in his paper that one of its purposes is the discussion of my paper entitled, Notes on the Physical Action of the Blast-Furnace,' with which he disagrees in part; and as the second stage of the discussion of this important subject has centered around his paper, some reply by me may not be amiss. Unfortunately, Mr. Meissner has not indicated a single statement or conclusion in my paper that he wishes to controvert; but as there is evidently a difference of opinion between us I will disregard this fact, and will discuss those conclusions of his that seem to me not to be justified by the facts of general practice, or even by the data which he produces to support them. Let me say, however, that I am a believer in the dry-air

Jan 1, 1908

By Robert Linton

SPECIFICATIONS for clays serving raw materials in the ceramic industry usually contain the following items: (1) Chemical analysis, sometimes with mineralogical structure determined by microscopic investigation. (2) Maturing temperature and firing range, usually expressed in terms of pyrometric cone equivalent. (3) Shrinkage (drying and firing shrinkage separately). (4) Degree of plasticity. (5) Color after firing. Clays may be classified, according to the purpose of the classification, in several different ways, based on (1) Geological occurrence-transported, altered An place, indurated (shales). (2) Physical properties-plastic (bonding clays, ball clays) and nonplastic (flint clays, kaolins or china clays, bone clays). (3) Color. (4) Use. A common classification of clays for commercial designation, and one fol-

Jan 1, 1936

THOSE MARKED THUS * ARE MEMBERS, MARKED THUS ?ARE ASSOCIATES. THESE SIGNS DOUBLED INDICATE LIFE MEMBERS AND ASSOCIATES RESPECTIVELY. THE FIGURES AT THE END OF THE ADDRESS INDICATE THE YEAR OF ELECTION. HEAVY-FACED TYPE SIGNIFIES HONORARY MEMBERSHIP. *AARONS, J. BOYD, Vivian Gold Mining Co., Ltd., Harris, West. Australia. '05 *ABADIE, EMILE R., Cons. and Min. Engr., 214 Union Savings Bank Bldg., Oakland, Cal. '76 ?ABBÉ, MAX F., Prest., Abbé Engineering Co, 220 Broadway, New York, N.Y. '07 *ABBOTT, CHARLES W., Min. Engr. Pioche, Nev. ?08 *ABBOTT, JAMES W., Min. Engr: Ploche, Lincoln Co., Nev. '94

Jan 1, 1917