Search Documents

By John J. Collins

[CONTENTS PAGE Purpose and scopeI Core samplingI Sludge sampling.....7 Combining core and sludge assays13 Deviation and surveying of drill holes17 Conclusions24 Acknowledgments25 Bibliography25] PURPOSE AND SCOPE The purpose of this paper is to review a few of the problems involved in the interpretation of diamond-drill core and sludge samples, with the hope that it will stimulate discussion and bring forth some of the information on the subject that has been accumulated by various organizations. The release of these data would benefit the mining industry as a whole. Particularly valuable would be the details of drilling programs that have been tested by actual mining operations, as most of the available published material is unsupported by production records. The scope of this paper is limited to a few of the commonest problems of interpreting diamond-drill core and sludge samples and the deviation of holes. It does not include the description of routine operations performed by the drillers, nor the estimation of ore reserves. The methods of calculating reserves have been described 25,26,31,32.50,65 but more information is needed on the results shown by actual mining operations. CORE SAMPLING The accuracy of diamond-drill-hole sampling depends in large measure on the percentage of core recovery. As a general rule, the longer the run, the poorer is the recovery. Although the longer runs allow cheaper drilling costs, the determining factor should be the percentage of recovery desired. The problem is one of balancing accuracy against costs. Holes of larger diameter may show improved recovery, except as Joralemon* points out that there are some conditions in which small holes give better core recovery than large holes. This is particularly true, he says, in rocks like shattered quartzite, where larger core tends to break in angular fragments and grind up, while the diameter of smaller core is less than the distance between joint planes and grinding is not so serious. In a large measure the length of the sample run should depend on the type of deposit. Favorable drilling may allow uniform sample runs of 5 ft., 10 ft., or perhaps 20 ft. In veins or beds of relatively narrow widths and changing characteristics, however, the ore zone may be overrun and ground in a core barrel full of waste rock. Generally it is desirable to break the sample at a change in the rock or ore. Such a change, often indicated by a color change in the sludge water, should be a signal for the driller to make a "dry" block and to pull out that run regardless of the length. Such a procedure permits the segregation of waste from ore samples so

Jan 1, 1946

By A. H. Daane, J. F. Haefling

BECAUSE of the wide use of platinum in industry and research, the physical properties of this metal, including its vapor pressure, have been studied in some detail.' The other members of the palladium-platinum group of metals have not been studied as extensively, and only qualitative information is available on the vapor pressure of palladium. Data given in literature by Vines1 and Brewer2 on the vapor pressure of palladium are based on the qualitative observations by Holborn and Austin3 and Crookes4 on the rate of volatilization of palladium filaments in various atmospheres. The general observation that palladium is the most volatile metal of the palladium-platinum metal group was corroborated by Bell, Love and Normand who studied the separation of isotopes of the platinum-group metals by a mass spectrometric method. We have measured the vapor pressure of palladium using the Knudsen effusion technique. In this work, the effusion vessel was suspended from a quartz-fiber microbalance into an induction furnace, and the amount of vapor effusing from the vessel was determined by direct weighing of the vessel during the measured heating times. This technique has been described in a report from this laboratory." The vapor pressure of palladium was calculated from these measurements using the equation P...... = 17.14 -W- (77m)'u [1] a t where ? is the weight loss in grams of vapor of molecular weight m from a vessel having an orifice of a sq cm, during t sec. The derivation of this equation from kinetic theory has been described in a previous report from this laboratory: as well as in texts discussing the kinetic theory of gases.%" Test Vessel—In the search for a suitable material for the effusion vessel, it was found that tantalum reacted with palladium metal to form intermetallic compounds, and graphite was readily dissolved in palladium metal to form what appeared to be a liquid phase at a temperature several hundred degrees below the melting point of palladium. On cooling, the graphite gathered into spherical balls in the palladium, with crystals extending radially from the center of these balls, some of which were a millimeter or more in diameter. However, palladium metal vapor did not attack the graphite vessel, so graphite could be used where it did not contact condensed palladium. Tungsten did not appear to react with palladium vapor or molten palladium at its melting point, but it was not convenient to use a tungsten-vapor pressure vessel because of the difficulty of fabricating this metal. Since the vapor-pressure range to be studied (10 2 to 10 ' mm) did not appear to extend above the melting point of palladium, a combination of tungsten and graphite served to provide a very satisfactory effusion vessel. The lower half of the graphite vessel was lined with some strips of tungsten foil and the sample of palladium consisting of a coil of sheet was placed in the tungsten liner; in this way, no contamination of the palladium by carbon occurred. Procedure After outgassing at 1500C, the tungsten-lined graphite effusion vessel was loaded with 300 mg of

Jan 1, 1959

By Morris Cohen

This paper deals with the calculation of the composition of the infinitesimal trace of alloy that transfers from the liquid to the solid state at each temperature during the equilibrium solidification of a binary solid solution, and which thereby enables the compositions of the coexisting liquid and solid phases to follow along the liquidus and solidus lines respectively during the cooling. A general expression for the composition (d) of the liquid-to-solid transfer at each temperature has been derived: d = ZLXL(XL - P) + Zsxs(P- ZL(XL - P) + Zs(P - Xs) where ZL and Zs are the slopes of the liquidus and solidus lines at the given temperature, XL and xs are the composi-tions of the stable liquid and solid phases at the same temperature, and P is the composition of the alloy under considera-tion. The d equation is valid for the process of equilibrium heating as well as cooling, and may be applied to vapor-to-liquid, vapor-to-solid, liquid-to-liquid, and solid-to-solid transfers if the corresponding equilibrium diagrams are known. The d -versus-temperature curves for two alloys Pl and P2 are shown in Fig. I. In each case, the liquid-to-solid transfer has the same composition as the stable solid FIG. I.-GENERAL SOLID SOLUTION DIAGRAM SHOWING S CURVES FOR ALLOYS P1 AND P2. phase only at the temperature of the be-ginning of solidification, and has the same composition as the stable liquid phase only at the temperature of the completion of solidification. At each intermediate tem-perature, the composition of the liquid-to-solid transfer differs by a finite amount from those of the two coexisting phases. Therefore, during equilibrium cooling, the transfers must merge into the solid phase from the liquid without forming a transition phase; otherwise the condition of equilibrium would be violated. At any given temperature during solidification, the composition of the liquid-to-solid

Jan 1, 1940

By J. R. CAIN

SAMUEL L. HOYT, ? Nela Park, Cleveland, Ohio (written discussion?). The work that Dr. Cain is doing on gases in steel should have a highly important bearing on investigational work in connection with steel-making practice. We found, for example, in our work in connection with the use of manganese in open-hearth practice that we needed expressions for the manganese efficiency and the "condition" of the steel. To get these figures we assumed that we would need to know the amount of FeO at different stages of the heat and the amounts of the gases present. This required simultaneous analyses of our samples for FeO and the gases and Dr. Cain seems to be the only investigator who has considered the analytical work from this point of view. That he has done so is very encouraging and it is to be hoped that his work will solve the mys-teries now surrounding this neglected phase of steel metallurgy. Those interested in the Ledebur method for use in connection with the efficiency of manganese as a "deoxidizing " agent will he disappointed to learn that more recent work at the Bureau indicates that Ledebur determinations are not reliable. The principal source of error seems to be due to the partial reduction of the ferrous oxide by the carbon present in the steel. However, it seems like an unnecessary criticism of the Ledebur method to state (p. 1319) that it proved of little value because it showed little differences in oxygen for a series of steels treated with ,various reagents and showing variations in physical properties and free-

Jan 12, 1919

By A. G. Metcalfe, A. Siede

The hardening of annealed copper during fatigue testing appears to be independent of the applied stress and to occur largely within the first 4000 cycles. Copper hardened by fatigue is more resistant to annealing than copper hardened by static means, and softens by a multistage process. Creep studies at 300°C show that copper hardened by fatigue also has greater resistance to creep than statically hardened copper. Some theoretical explanations are discussed. RECENT interest in the behavior of metals subjected to fatigue stems from observations of phenomena which could not be explained by current theories of the structure of metals. In 1953 Bullen et al.l showed that the hardening caused by fatigue at low stresses did not cause severe bending of the lattice as did hardening by static methods. This was later confirmed by Wood, 'and Broom and Ham.3 Clarebrough et al4 showed that as the stress level used in fatigue hardening was increased, bending of the lattice was introduced, eventually approaching that of metals deformed by conventional cold-working methods. The type of hardening introduced by fatigue has other interesting characteristics. Kemsley5 showed that copper fractured by fatigue at low stresses resisted annealing as compared to copper hardened an equal amount by static means. The work of Clarebrough etal, shows that the manner of energy release during annealing differs for fatigue-hardened and statically hardened metal in both magnitude and temperature range of release. In addition to hardening of the lattice, fatigue has been shown to cause softening in materials previously hardened by static methods,5 and also in age-hardened alloys.7 The superposition of a small fatigue stress on the static loading of high-temperature alloys has been shown to increase their resistance to creep.' The present work was an attempt to determine the relationship between fatigue hardening, resistance to annealing, and the creep properties of pure copper. EXPERIMENTAL PROGRAM The program described here was designed to answer three questions: 1) Can stress-cycle combinations well below the failure values give significant increases in hardness? 2) Does hardening, under different stress-cycle combinations, give increase resistance to annealing? And if so— 3) Does superior resistance to annealing confer superior creep properties over statically hardened material? Three-quarter hard OFHC copper was annealed in vacuo at 550°C for 1 hr to produce a strain-free material having a fine grain size and uniform hardness. (The standard deviation of the mean hardness of the annealed samples was less than + 1.9 Dpn). Annealing was performed after machining the fatigue specimens so as to avoid work-hardened surfaces. Jigs were used to avoid distortion. The fatigue properties of the annealed copper were determined using an accurately aligned Baldwin-Sonntag SF1-U machine operating at 1800 cycles per min. This limited the minimum number of cycles which could be examined to about 4000 stress reversals. Since failure resulted in specimen damage, hardness increase with number of cycles was measured by testing specimens fatigued to different fractions of the failure values. The results are shown in Fig. 1, and are superimposed on the S-N curve of the copper in Fig. 2. The resistance to annealing of fatigue-hardened material was compared to that of material hardened by uniaxial tensile straining. Specimens hardened to equal values by both methods were progressively annealed for 1 hr at temperature in vacuo. After each annealing treatment the hardness was measured using a Leitz Durimet hardness tester with a 500-g load. At least five tests were made for each hardness determination. The standard deviation for individual specimens varied from 0.26 to 1.48 hardness points. The results are shown in Figs. 3 to 5. The discontinuous nature of the annealing process has been brought out by drawing idealized curves through the data points. This can be justified by the consistency of the results as well as by general agreement with results of Kemsley.5 The creep resistance of fatigue-hardened and

Jan 1, 1960

By John J. Collins

Page Purpose and scope..................... 521 Core sampling......................... 521 Sludge sampling....................... 527 Combining core and sludge assays ...... 533 Deviation and surveying of drill holes. . . . 537 Conclusions........................... 544 Acknowledgments...................... 545 Bibliography.......................... 545 Purpose and Scope The purpose of this paper is to review a few of the problems involved in the interpretation of diamond-drill core and sludge samples, with the hope that it will stimulate discussion and bring forth some of the information on the subject that has been accumulated by various organizations. The release of these data would benefit the mining industry as a whole. Particularly valuable would be the details of drilling programs that have been tested by actual mining operations, as most of the available published material is unsupported by production records. The scope of this paper is limited to a few of the commonest problems of interpreting diamond-drill core and sludge samples and the deviation of holes. It does not include the description of routine operations performed by the drillers, nor the estimation of ore reserves. The methods of calculating reserves have been described,25,26,31,32,50,65 but more informa- tion is needed on the results shown by actual mining operations. Core Sampling The accuracy of diamond-drill-hole Sampling depends in large measure on the percentage of core recovery. As a general rule, the longer the run, the poorer is the recovery. Although the longer runs allow cheaper drilling costs, the determining factor should be the percentage of recovery desired. The problem is one of balancing accuracy against costs. Holes of larger diameter may show improved recovery, except as Joralemon* points out that there are some conditions in which small holes give better core recovery than large holes. This is particularly true, he says; in rocks like shattered quartzite, where larger core tends to break in angular fragments and grind up, while the diameter of smaller core is less than the distance between joint planes and grinding is not so serious. In a large measure the length of the sample run should depend on the type of deposit. Favorable drilling may allow uniform sample runs of 5 ft., 10 ft., or perhaps 20 ft. In veins or beds of relatively narrow widths and changing characteristics, however, the ore zone may be overrun and ground in a core barrel full of waste rock. Generally it is desirable to break the sample at a change in the rock or ore. Such a change; often indicated by a color change in the sludge water, should be a a for the driller to make a "dry" block and to pull out that run regardless of the length. Such a procedure permits the segregation of waste from ore samples so

Jan 1, 1946

Jan 1, 1947

Jan 1, 1947

By I. W. L. Finlay, H. R. Ogden, R. Jaffee, D. J. Maykuth

Aluminum has been found to be soluble in a titanium to about 26 pct, and to raise the temperature range of transformation from a to 8. Two intermediate phoses exist in the system, a new face-centered tetragonal phase, designated as 7, which occurs between 34 and 46 pct Al, and TiAI Metallographic and X-ray diffraction data were used to determine the diagram. ALUMINUM is one of the useful alloying additions for titanium-base alloys. It is an important constituent in two commercial alloys released in 1950, one containing 4 pct A1 and 4 pct Mn, and the other containing 3 pct A1 and 5 pct Cr as the metallic alloy content. It is probable that, in the future, other titanium alloys containing aluminum will be released. In the course of alloy development work, some of the features of the constitution of titanium-rich Ti-A1 alloys have been developed. These are described in the present paper. The only available information on the Ti-A1 system concerns the aluminum-rich end of the diagram. In summarizing the early work, Hansen' indicated that there is little solubility of titanium in aluminum, and that a two-phase region exists up to the intermediate compound, TiA1a (37.2 wt pct Ti), which has a congruent melting point at 1355°C. Fink' has reported that a peritectic reaction occurs at 665°C between the melt and TiA1³ to form the terminal solid solution of titanium in aluminum. The solubility of titanium in aluminum has been established at 0.24 pct at 510°C and is estimated to be between 1 and 1.5 pct at the peritectic temperature. No information has been published on the diagram above TiAl,, other than a statement- hat aluminum raises the a to ß transformation temperature of titanium. Materials and Preparation of Alloys Iodide-type titanium and high-purity aluminum were used in this investigation. Typical analyses of these materials are given in Table 1. Alloys were prepared by arc melting on a water-cooled copper hearth, using the techniques described previously for contamination-free melting.' Weight losses during melting were very low, ranging from 0 to 0.02 g in a 10 to 15 g charge, indicating that little or no loss of aluminum occurred during melting. This permitted the use of nominal compositions for these alloys. Alloy ingots containing from 0 to 7.5 pct A1 were rolled in air at 850°C to 0.040 in. sheet. Alloys containing from 7.5 to 16 pct A1 could only be rolled about 25 pct reduction at temperatures up to and including 1200°C. Alloys containing above 16 pct A1

Jan 1, 1952

By Everett G. Trostel

AMERICAN industry in 1943 emerged from the construction phase into the production phase, and American military operations passed from preparation into full action in the many theaters of the global war. The increased pace of industrial and military operations has resulted in a tremendous demand for petroleum and its products.

Jan 1, 1944

By Fun-Den, Wang

An open pit rock structure usually contains geological planes of weakness. They are formed by joints, faults, bedding planes, fractures, and cleavages. Rock slope failures often occur in the form of sliding of rock blocks along a plane or several planes. Such a rock block has three- dimensional geometry, and consequently a vector method of analysis has been found useful in evaluating its stability. Rock blocks of a tetrahedral shape with one free surface have been analyzed by Londe. Rock blocks formed by sets of parallel joints have been analyzed by Wittke. The present chapter presents the analysis of rock blocks formed by planes of weakness of arbitrary orientation, and of three-dimensional geometry.

Jan 1, 1972

The industrial might of the Bowen Basin is primarily the result of Utah Development Co.'s work- which has opened up the Blackwater, Goonyella, Peak Downs, and Saraji mines; built the Hay Point port; and is now developing the Norwich Park mine.

Jan 1, 1977

By C. Kremer Bain

DURING the past several years of diamond drilling in Washington County, Mo., the St. Joseph Lead Co. has discovered a concentration of commercial lead-zinc ore at four different points within an area of 36 square miles. The largest and to date the most promising group of these orebodies is located in the Indian Creek area. It was considered to be of sufficient value to warrant development. The Indian Creek area is in the center of the northern half of Washington County, 11 miles northwest of Potosi, Mo., the county seat. The location is readily accessible from Potosi by car or truck over the all-weather Missouri State Highway No. 114. The topography is one of rolling relief, varying from an elevation of 700 ft above sea level on Mineral Fork and Indian Creek to a maximum of 1176 ft at High Point Tower. It is divided in equal halves between the drainage to Mineral Fork and to Indian Creek. The shaft site at 1060 elevation is on the divide between the two drainage areas. The Indian Creek side is rough and heavily wooded, with only a few cultivated clearings. The slopes to Mineral Fork are more gentle and rounded, with much of the area cleared for farm land. Most of the surface is covered with Potosi and Eminence formations, which show little evidence of any structure. Ore structure was worked out by extensive diamond core drilling, with holes varying in depth from about 700 to 1300 ft. As of Oct. 1, 1950, 218 prospect holes had been drilled within the 36-square mile area. The ore is disseminated galena with considerable accompanying sphalerite in the Bonne Terre forma-tion in the shape of irregular blanket-type deposits. The main controlling structural feature of the outlined mineral zone is a buried pre-Cambrian rhy-olite-porphyry ridge extending partly through the Bonne Terre formation, which laps against the por phyry and also covers it. The mineralized zone parallels and forms an irregular halo around the porphyry ridge and is concentrated in the Bonne Terre formation where the La Motte sandstone is cut out by the porphyry ridge. This is a very common mineral occurrence in the southeastern Missouri lead belt district. The La Motte sandstone, which normally underlies the Bonne Terre formation, is thus cut out entirely. In this area the Bonne Terre is usually about 275 to 320 ft thick, the La Motte varying in thickness from zero up to 400 ft. Commercial concentrations of ore are indicated at several places, the most notable being at the shaft site where an orebody at least 4000 ft long with widths of 500 to 600 ft has been outlined. The total thickness of mineralized rock reaches 150 ft in some holes, although total ore thickness runs from 8 ft to about 60 ft, often in more than one layer. Preliminary Planning Ore reserves as outlined lend themselves to open-stope mining with trackless haulage and mobile loading machines and drilling equipment. This type of equipment has proved to be very efficient during recent years in the company's lead belt operations. After a study of bids for shaft sinking and an estimation of comparative costs, it was decided that the shaft would be sunk by St. Joseph Lead Co. personnel using company equipment. Since the plant site is about 26 miles from the company's nearest lead belt operations, it was necessary to plan a complete surface plant, including mill, shops, office, change room, and warehousing facilities. Immediately following the filing of an application for a certificate of necessity, a headframe was selected for which detailed drawings were already available. The order was placed for fabrication so that it could be delivered and erected in time to serve for sinking the shaft. This eliminated the expense of a temporary headframe. Drilling was started on two churn drill holes near shaft location, and two 1000-gpm deep well pumps

Jan 1, 1954

By Richard P. E. Hermsdorf

IN the nonferrous sessions this year, magnesium wiggled its way into a dace of prominence such as it has never before enjoyed. This was evidenced not only by the number of papers presented on that metal but by the attendance at the meetings. The atmosphere permeating these magnesium meetings was similar to that which exists in a family with a new baby. Everybody crowded around to see what it looked like and then wondered whether it would be a success and credit to the family. Well. magnesium appeared to be a vigorous youngster, full of life, and raring to go. A close relative of maenesium named " aluminum, although much more grown up, also attracted much attention. From the activity and spirit in these sessions

Jan 1, 1944

By Becket, Frederick M.

CHROMIUM is but one hundred and thirty years of age-a mere youngster as related to many metals that' have speeded world progress. It was Vauquelin of France who proved conclusively that the so called red lead of. Siberia contained a new element. The variety and characteristic colors of the compounds suggested the name chromium. He also succeeded in reducing oxide of chromium to the metallic form and described the product as very brittle, infusible, needle- like crystals on which acids had very feeble action. His metal was not pure chromium, of course; it must have contained appreciable carbon in the combined form as a result of reducing the oxide by carbon at high temperatures. Vauquelin's description in 1798 of this work is a gem-indeed, literally, he went so far as to discover the presence of chromium oxide in the emerald. The metallic product did not seem to interest Vauquelin greatly, but a new chemical industry began shortly after his discoveries.

Jan 1, 1928

By A. M. Rowe, I. H. Silberberg

A computer program was written to predict the phase behavior generated by the enriched-gas-drive process. This program is based, in part, on a new concept of convergence pressme, which is then used to select vapor - liquid equilibrium ratios (K-factors) for performing a series of flash calculations. The results of these calculations are the equilibrium vapor and liquid phase compositions which define the phase envelopes. The program was used to predict phase envelopes for 11 different hydrocarbon systems on which published experimental data were available. The predicted and experimental results compare favorably. INTRODUCTION The reservoir engineer is frequently faced with the problem of predicting what will happen if gas is injected into a reservoir. One aspect of this, general problem is predicting the phase changes that will occur when a non-equilibrium gas displaces a reservoir fluid. In particular, a "dry" gas, upon displacing a volatile oil, will pick up intermediate components from the oil. On the other hand, a "wet" gas, containing a high concentration of intermediates, will lose some of these components to a relatively low-gravity, non-eouilibrium1- crude. It is this latter Drocess. occurring in the enriched-gas displacement, which is treated in this paper. In the past, these phase changes have been determined experimentally and the results incorporated into various modifications of the Buckley-Leverett analysis.112 Such experimental work is time consuming, and the results are sensitive to numerous experimental errors. With the wide availability of high-speed digital computing equipment and numerous correlations pertaining to the vapor-liquid equilibria of hydrocarbon systems, it is now practical to calculate such phase behavior. This paper describes a computer program for performing these calculations. THE ENRICHED GAS DISPLACEMENT PROCESS Experimental results have shown that oil recovery can be significantly increased by enriching the displacing gas with intermediate hydrocarbon c0m~onents.3 The essential features of the phase behavior generated by this enriched-gas-drive process are commonly illustrated with ternary diagrams such as Fig. 1.4 In this figure, Gas D, which contains a high concentration of intermediate hydrocarbons with respect to the undersaturated Crude A, is injected into the reservoir. When D contacts A, gas goes into solution until the oil becomes saturated (Point. B). Further contacting of Gas D and saturated Oil B results in a Mixture C which separates into Vapor Y(c) and Liquid X(c). Liquid X(c) is contacted by additional Gas O, resulting in Mixture E which separates into Vapor Y(e) and Liquid X(e). Repeated contacts of the liquid by the injected gas will eventually result in Liquid X(4 of maximum enrichment existing in equilibrium with Gas Y(d). The equilibrium tie-line X(4 Y(4, when extended, passes through the Point D representing the enriched injection gas. For systems of more than three components, the predicted equilibrium states are dependent upon not only reservoir temperature and pressure, but also the compositions of the crude oil and injected gas. If the gas is sufficiently enriched, a miscible displacement is generated. Line If is tangent to the phas,e envelope at the critical point (Point Z) and represents the limiting slope of the tie-lines as the critical state is approached. Point 1 therefore represents the minimum enrichment of injection gas required to generate a miscible displacement. Point G represents the minimum enrichment required for initial miscibility of the injection gas with Crude A. Accra has presented a method to be used for prediction of oil recovery by the enriched gas displacement process.l To develop the phase behavior data needed, he designed the experimental procedure described in the following quotation from his paper: The original liquid was contacted by a volume of displacing gas and allowed to come to equi-

Jan 1, 1966

By L. R. MacLead

Delivery of tailing to any part of the area by gravity from the ridge was found practicable. Experiments with asbestos-cement pipe proved it possible to use level pipe across the dams if it is fed through an inclined section in which pressure could be developed. Use of pipe to transfer the tailing to the dams was not favored because of the possibility that choking might occur. Metal flume was not believed to have sufficient wear resistance on this material and wooden flume would not withstand damage by the weather so well- Flume -action made- of 26-in diameter asbestos-cement pipe, split before curing and molded to a specified cross section, were finally approved. The flume is connected to the 24-in. diameter tail in distribution pipe by heavy concrete lateral launders. Cascades of horizontal and vertical pipe sections are used at the top of the pressure leg where scouring by high-velocity flow of tailing might occur.

Jan 1, 1942

By S. A. TAYLOR

THERE is probably no other mineral industry of which the public has as much information and misinformation as it has of the coal industry. Unfortunately, however, the general public's knowledge of the coal industry, outside of the particular kind of coal it is accustomed to, by reason of use, is largely made up of information received from newspaper and popular magazine articles, in which the mine workers are depicted as overworked and mistreated men, and the coal operators as "coal barons." Those who have any specific knowledge of exact conditions in the coal industry know how unjust and un- fair such an opinion of the coal industry is, not only to the miner but to the operator as well. Many reporters and writers of magazine articles are misled by statements regarding the condition of the miners that are exaggerated and not founded on facts and, if an investigation of the conditions of the miner's work, his habitation and surroundings were fairly made, it would at least compel more truthful statements by those who write for public reading. That such an investigation would not reveal anything that was wrong, or anything to be censured or cured, no one, I think, would maintain, but I do think that any fair investigation of the facts would show that conditions in and around the newer and later-developed coal mines and communities would compare favorably with those of manufacturing districts, and that where the mines and com- munities are old and not very attractive places to work, or live in, they carry with them other considerations, compensating for these conditions, and cannot be remedied by reason of a lack of sufficient coal to warrant economically any costly changes.

Jan 1, 1926

By M. R. J. Wyllie

The relationship between the electromotive force (E.M.F.) across a shale barrier and the concentrations of sodium chloride solutions on either side has been investigated. It is shown that the action of a shale barrier is analogous to a glass membrane separating two acid solutions of different hydrogen ion concentrations. The shale behaves as a sodium electrode and is responsive to the activities of the sodium ions in the two solutions in such a way that the potential can be calculated by means of the Nernst equation. This conclusion is confirmed by laboratory experiments. In a borehole the total E.M.F. of a shale cell is the algebraic sum of the ~otential across the shale and a boundary potential. The relationship between total E.M.F. and the resistivity ratio of two sodium chloride solutions is indicated for a number of formation temperatures. The E.M.F. thus predicted is then compared with the .elf potential read from an electric log and good agreement is demonstrated. Based on both the self potential and resistivity curves of the electrical log. a method is given for calculating connate water content in a bed having in-tergranular porosity and containing both connate water and hydrocarbons. INTRODUCTION The first paper on electrical well logging by C. and M. Schlumberger and E. G. Leonardon in 1934' attributed the self potential curve principally to streaming potentials, i.e. to electroki-netic effects. Almost immediately great difficulties were encountered in reconciling many of the curves they obtained with this interpretation. and a ~econd paper' by the same authors soon appeared. In this second paper self potentials were attributed to the combined effects of streaming potentials and electrochemical potentials, the electrochemical potential being considered the result mainly of the interaction of fluids of differing salt concentrations, i.e. a boundary potential, and partly of potentials set up at the faces of impermeable materials. Some experiments involving a gray clay for the impermeable material were quated. The Schlumbergers and Leonardon deduced from the equation for a simple boundary ~otential that the electrochemical potential, as opposed to the electrokinetic potential, could be expressed in the form E=Klog- .......1 pe where K is a constant, pm the mud resistivity. p, the resistivity of the connate water in a porous bed. However, no general expression for the constant K was obtained. Although the literature between 1934 and 1943 contains a number of quotations of their results, the valuable work of the Schlumbergers and Leonardon was not extended so that the electrochemical potential has been generally attributed wholly to boundary potentials between the mud in the borehole and the connate waters in porous formations. Unfortunately, however, the fundamental premise of all these papers, that a boundary potential can give rise to current flow in a borehole, is thermodynamically untenable. As will be shown. the fact that the electrochemical potential can be fairly accurately express as E = K log pm/pc, a form in which a boundary potential may also be written, is partly fortuitous. The boundary potential is indeed an integral part of the expression for the electrochemical potential in a horehole, but in magnitude it represents only about 20% of the total potential. In 1943 an important step in the elucidation of electrochemical potentials was made by Mounce and Rust3 who showed that if a wall of shale separated two compartments which contained saline solutions of different concentrations, and if the two solutions were themselves brought into contact in the pores of a porous inert membrane (such as unglazed porcelain) a current flowed through the shale and saline solutions. The direction of positive current was from the shale into the more dilute solution. The paper of Mounce and Rust, while repeating some of the observations of the Schlumbergers and Leonardon, seems to be the first to show that the shale was the seat of a genuine electrochemical effect capable of causing current flow. In the same paper Mounce and Rust pointed out the similarity between the fundamental conditions of their experiment and the conditions which existed when a bed of shale in the ground was simultaneously in contact with a porous sand containing saline connate water and mud fluid of salinity different from that of the water in the sand. Since it is now generally recognized that the S.P. curve measures ohmic potential changes in the mud fluid in the well bore resulting from changes in current flow, it is apparent that currents having their origin in the electrochemical interaction of mud filtrate and connate waters with shale beds are a very important portion of the total S.P. The work of Mounce and Rusta and others appears to indicate that, in general, the electrochemical portion of a particular kick on a S.P. curve far exceeds any electrokinetic potentials resulting either from streaming potentials or Dorn effects. The Dorn effect, or sedimentation potential. arises when small particles are allowed to fall through certain fluids under the influence of gravity. a difference of potential being observe? between two electrodes placed at different levels in the stream of falling particles. The Dorn effect is unlikely to affect seriously the S.P. curve as now measured. A successful analysis of the electrochemical aspects of the S.P. log should

Jan 1, 1949

By M. R. J. Wyllie

The relationship between the electromotive force (E.M.F.) across a shale barrier and the concentrations of sodium chloride solutions on either side has been investigated. It is shown that the action of a shale barrier is analogous to a glass membrane separating two acid solutions of different hydrogen ion concentrations. The shale behaves as a sodium electrode and is responsive to the activities of the sodium ions in the two solutions in such a way that the potential can be calculated by means of the Nernst equation. This conclusion is confirmed by laboratory experiments. In a borehole the total E.M.F. of a shale cell is the algebraic sum of the ~otential across the shale and a boundary potential. The relationship between total E.M.F. and the resistivity ratio of two sodium chloride solutions is indicated for a number of formation temperatures. The E.M.F. thus predicted is then compared with the .elf potential read from an electric log and good agreement is demonstrated. Based on both the self potential and resistivity curves of the electrical log. a method is given for calculating connate water content in a bed having in-tergranular porosity and containing both connate water and hydrocarbons. INTRODUCTION The first paper on electrical well logging by C. and M. Schlumberger and E. G. Leonardon in 1934' attributed the self potential curve principally to streaming potentials, i.e. to electroki-netic effects. Almost immediately great difficulties were encountered in reconciling many of the curves they obtained with this interpretation. and a ~econd paper' by the same authors soon appeared. In this second paper self potentials were attributed to the combined effects of streaming potentials and electrochemical potentials, the electrochemical potential being considered the result mainly of the interaction of fluids of differing salt concentrations, i.e. a boundary potential, and partly of potentials set up at the faces of impermeable materials. Some experiments involving a gray clay for the impermeable material were quated. The Schlumbergers and Leonardon deduced from the equation for a simple boundary ~otential that the electrochemical potential, as opposed to the electrokinetic potential, could be expressed in the form E=Klog- .......1 pe where K is a constant, pm the mud resistivity. p, the resistivity of the connate water in a porous bed. However, no general expression for the constant K was obtained. Although the literature between 1934 and 1943 contains a number of quotations of their results, the valuable work of the Schlumbergers and Leonardon was not extended so that the electrochemical potential has been generally attributed wholly to boundary potentials between the mud in the borehole and the connate waters in porous formations. Unfortunately, however, the fundamental premise of all these papers, that a boundary potential can give rise to current flow in a borehole, is thermodynamically untenable. As will be shown. the fact that the electrochemical potential can be fairly accurately express as E = K log pm/pc, a form in which a boundary potential may also be written, is partly fortuitous. The boundary potential is indeed an integral part of the expression for the electrochemical potential in a horehole, but in magnitude it represents only about 20% of the total potential. In 1943 an important step in the elucidation of electrochemical potentials was made by Mounce and Rust3 who showed that if a wall of shale separated two compartments which contained saline solutions of different concentrations, and if the two solutions were themselves brought into contact in the pores of a porous inert membrane (such as unglazed porcelain) a current flowed through the shale and saline solutions. The direction of positive current was from the shale into the more dilute solution. The paper of Mounce and Rust, while repeating some of the observations of the Schlumbergers and Leonardon, seems to be the first to show that the shale was the seat of a genuine electrochemical effect capable of causing current flow. In the same paper Mounce and Rust pointed out the similarity between the fundamental conditions of their experiment and the conditions which existed when a bed of shale in the ground was simultaneously in contact with a porous sand containing saline connate water and mud fluid of salinity different from that of the water in the sand. Since it is now generally recognized that the S.P. curve measures ohmic potential changes in the mud fluid in the well bore resulting from changes in current flow, it is apparent that currents having their origin in the electrochemical interaction of mud filtrate and connate waters with shale beds are a very important portion of the total S.P. The work of Mounce and Rusta and others appears to indicate that, in general, the electrochemical portion of a particular kick on a S.P. curve far exceeds any electrokinetic potentials resulting either from streaming potentials or Dorn effects. The Dorn effect, or sedimentation potential. arises when small particles are allowed to fall through certain fluids under the influence of gravity. a difference of potential being observe? between two electrodes placed at different levels in the stream of falling particles. The Dorn effect is unlikely to affect seriously the S.P. curve as now measured. A successful analysis of the electrochemical aspects of the S.P. log should

Jan 1, 1949