Search Documents

By John Griffen

THEORY HYDRAULIC classification as explained by Rittinger and others was largely restricted to conditions wherein the free-falling velocities of the particles were conceived as governing the separations effected (see chapter 9). The laws governing classification under free-falling conditions have been summarized by Chapman and Mott as fo1lows:l Nomenclature r represents, in a particle of irregular shape, the round-hole screen through which the particle would pass, or some other linear dimension of the particle equivalent to d, the diameter of a sphere. s, the specific gravity of the particle. 1, the specific gravity of the water used as a medium. K, a constant. W, the velocity of the water. In an Upward Current of water 1. A particle will move upward if [V > K dr(s - 1)] and, by suit- ably regulating the speed of the water current, the larger and heavier particles may be made to fall downward against the current, leaving the smaller, lighter particles in suspension in the current. 2. Particles such that [- = -] cannot be separated in an upward- current classifier with any one velocity of current. Coal particles having a specific gravity of 1.35 cannot be separated from refuse particles of [2.5 - 1 2.5 sp. gr.] unless the ratio of diameters is less than [ 4.3 to 1, 1.35 – 1] and the raw coal must be screened to size limits within this ratio if they are to be separated. Cone-shaped vessels or vessels of other shapes that allow the use of different velocities of current at different points in the flow are used to modify this limitation.

Jan 1, 1943

By R. C. Gifkins, K. U. Snowden

The value of the index n in power ktivs for the stress sensitivity of minimum creep rale at lead is derived front results drawn from lite literature and from previously unpublished nork on commercial (99.99 pel) and high-purity (99.999 pel) lead polycryslalline and hi crystal specimens. In tests al 0.5Tm (22 to 50'C) for slvesses below 250 psi, n fulls to mily for poly-cr,yslullirle specimens, single crystals, and bicrystals, and toy grain boundary sliding in bicrystals. Between 250 and 500 psi there is a tyansilion range and, for the polycrystalline specimens al least, u high-stress regime for 500 to 1500 psi where n is 5 or 6. These results are such that none of the suggested stress taws can he used to extrapolate to very loir stresses. Meclianisms for deformation in Ike grains and toy grain boundary sliding in the low-strcss regime are outlined. In particular, the mechanism for grain boundary sliding involves sliding controlled by diffusion from tensile to compressire Ledges. predictions based on this model give promising numerical agree-nicul with experiment. II is suggested that the mechanism for grain boundary sliding may he important in other circumstances, e.g., in creep of ceramic materials or superplaslicity, because it can operate with lille or no dislocation aclirity. WhEN the stress dependence of secondary creep rate is represented by a power law the values taken by the stress exponent n are found to vary between 1 and 7, see, c.g., Garofalo.' In Eq. 1 11 u is the applied stress and A a constant. The case for accepting values of v = 1 rests principally upon tests at high temperatures (>0.9Tm) and there have only been isolated tests at lower temperatures (rather than plots of creep rate against stress) for which the creep rates are such that some form of Nabarro-Herring creep with n = 1 is applicable. Hanson5 and Greenwood and cole6 plotted creep rate against stress for tests made in the vicinity of 0.5Tw, and found a "creep yield", so that below a certain low stress the creep rate was linearly related to stress: these observations appear to have been subsequently ignored. Various models have been proposed which agree with a large body of experimental results in which n equals -5 at high stresses (e.g., weertman7 and McLean8). Various alternatives to Eq. [1] have been proposed principally as a means of unifying creep data, but sometimes, it seems, in order to obviate the necessity for assuming a series of regimes of deformation associated with the various values of n; further refer- ence to these will be made in the section on stress laws. This paper calls attention to extensive results which show n = 1 for the creep of lead at room temperature (0.5 T,). RESULTS Fig. 1 is a composite diagram based on figures in the literature6,9,10 with additional results obtained by the present authors and their colleagues11,12 in the course of a number of investigations not directly concerned with stress sensitivity. In Fig. 1 In creep rate is plotted against In stress. The curves show results for two kinds of material. Lead I is of commercial purity (99.99 pct Pb) and lead IT a specially refined material, hydrogen-purified to remove oxygen; it contains 99.999 pct Pb. Curve A is for lead I in polycrystalline form (grain diameter 0.02 to 0.05 cm) at room temperature (22' to 26°C). Curve B1 is for lead I, polycrystalline, tested at 50C. Curve B2 is for lead 11, polycrystalline (grain diameter 0.02 cm), tested at room temperature (22 O- Curves C to F relate to tests made of bicrystals of lead 11: all of the same nominal orientation ("Y" in Ref. 12). Curves C and V are for creep within the component crystals of the bi crystals at 22°C (AB and CD in Fig. 2). Curve E is for creep measured in a gage straddling the boundary, approximately 0.15 mm either side (BC in Fig. 2). Curve F shows rates of grain boundary sliding (as distinct from strain rates in the other curves), obtained by averaging the offsets of six marker lines on the bi-crystal boundaries. The principal feature of the results is that the stress sensitivity falls into two distinct regimes, according to whether the stress is below approximately 250 or above 500 psi (there is a transitional range between 250 and 500 psi). The new result is that below -250 psi two of the curves (A and BI) give a value of n 1, and the other curves also drop below n - 2 to -1.5 but do not extend to low enough stresses to show clear evidence of n 1. At very high stresses the curves tend to give values of n - 6, as previously determined in other investigations. Curve R2 for the high-purity lead in polycrystalline form at room tenlperature almost merges with B, and thus gives new significance to the values for stresses of 150 and 200 psi; previously'3 these points had seemed to fall away from the curve of slope -3, but they now can be seen as almost completing a transition to n = 1. It should be noted that there was originally considerable apparent scatter in the results for the high-purity lead. However, this was found to be associated with annealing conditions or variations in residual content of oxygen and curve B2 was constructed using the highest rate (i .e., the rate for the purest lead) determined for each stress during the course of various investigations over the years: altogether, some forty tests were used in constructing curve R2.

Jan 1, 1968

By M. E. Wadsworth

The chief value of a paper like this consists in its statistical tables, putting on record material useful to future inquirers. The data here given have been compiled from time to time as far back as 1874, and subsequently brought up to date. Much of the data could only be procured by personal inspection of the catalogues, as for example those relating to the Lawrence Scientific School, which were taken at that time from the catalogue of Harvard University, on file in the University Library, by the present writer, then an instructor in that institution. These tables of statistics were first prepared for publication by the present writer in 1888-1890 and published in his "Report to the Board of Control of the Michigan College of Mines " (Michigan Mining School) for 1886 to 1890. Later they were revised, enlarged and brought down to date in his reports to the same Board for 1890-92; and since that time they have been, at his request, revised, greatly enlarged and kept up to date by Mrs. Frances H. Scott, the efficient Librarian and Secretary of the Michigan College of Mines. Great credit is due to her for her devotion to this work and her untiring efforts to have the statistics complete as far as possible. The accompanying running commentary is given simply as a string to hold these statistics together, and in order to call attention to a few points. In compiling any tables like those accompanying this paper, one is confronted by serious difficulties, some of which render these results only approximate. In order to insure greater correctness and fullness in the statistics to be published the writer's reports for 1890-92 were sent to the president of every college, university, and technical school in the country, so far as known. Accompanying this was a personal letter which asked of each one his aid in correcting any errors, and in giving fuller statistics. But relatively few answers were obtained, and subsequently from one to many letters have been sent to each institution not formerly reply-

Jan 1, 1898

By A. Keil

TO measure the absolute conductivity of metallic specimens it is generally necessary to have exact geometrical shapes and good electrical contact with the test-piece. To overcome limitations of the standard methods, an electronic conductivity-meter* Trade name, Sigmatest; model Dr. F. Forster; Reutlingen, Ger-many. has been developed, which works on the principle of inducing high frequency eddy-currents in the specimens and measuring the reaction of these curients on a measuring coil.',' To attach the instrument to the test specimen, a flat area of about 10 mm diam is all that is necessary. The reading is taken off a scale calibrated in pet of International Annealed Copper Standard. The induced eddy-currents are propagated in a circular motion parallel to the surface. Thickness of the layer included in a measurement depends on the frequency used. With a frequency of 60 kc per sec, the penetration of the currents was 0.8 mm at the upper limit of the scale, and 2 mm at the lower limit. The method is limited to nonferrous metals and other applications have been described elsewhere." The object of the present investigation was to detect the formation and growth of surface layers of differing conductivity, and to determine the depth to which these changes could be observed. A well known phenomenon which illustrates the problem is the internal oxidation of certain silver alloys containing base metal solutes, such as copper or cadmium, when they are annealed in an oxidizing atmosphere.4, 5 Until now, the only methods available for following these phenomenon have been metallo-graphic examination and hardness tests.0, 7 Changes in mechanical properties of copper alloys by internal oxidation were recently discussed in a more general way by Martin and Smith." When measuring these conductivity changes it must be remembered that the only absolute values of conductivity are those of 1) the nontreated homogeneous specimen, and 2) the final values obtained with a surface layer of depth comparable to the penetration of the eddy-currents. All intermediate values refer to the mixed conductivities of the transformed surface layer and the untransformed alloy, and are thus readings of relative value only. Experimental Results Specimens were annealed for 1/2 hr at 800°C in hydrogen, and the internal oxidation was carried out by thermal treatment in air at 800°C. Fig. 1 shows the results of the first series of experiments. With internal oxidation of a solid solution of 8 pet Cd in silver, the conductivity rises continuously until the surface layer formed has become thick enough to be the deciding factor (about 400µ). Precipitates of CdO are mainly in the form of points, Fig. 2, and, as a result, the electric contact between the silver crystals is not distorted by them. Brine11 tests were run with a 1.25 mm ball and a 7.812 kg load. The specimen annealed in hydrogen and oxidized to a depth of 400µ had a hardness of 40 Bhn,

Jan 1, 1959

By Frederick Laist, H. J. Maguire

The ore from the Butte mines of the Anaconda company is quite siliceous; that is, it contains considerably less iron than is needed for the fluxing of the silica. The direct smelting of this ore, therefore, requires the addition of considerable fluxing material. The only flux available in sufficient quantity at Anaconda is limestone containing no metallic minerals. This necessarily makes the direct smelting of the ore so expensive that it is more profitable to subject the ore to a preliminary treatment by concentration. However, as the losses in the concentrator were very high, compared with the losses in the blast furnaccs, it was found, by calculation, more profitable to send ores containing more than a given percentage of copper to the blast furnaces, in spite of the higher costs of treatment. The dividing point was dependent on various factors, the chief of which was the prevailing market price of copper. It was customary, therefore, to segregate the ore as mined into two classes. Ore in the first class generally contained 5 per cent. or over of copper; this was sent directly to the blast-furnace department. Second-class ore contained less than 5 per cent. of copper, and averaged around 3 per cent.; it went to the concentrating department. With the introduction of the flotation process, it mas found possible to maintain an average recovery, as concentrates, of 96 per cent. At the same time, the cost of reverberatory smelting was very materially decreased by the use of pulverized coal. These two changes in practice made the blast furnaces unable to compete with the reverberatory furnaces on a cost basis. The distinction between first- and second-class ore was therefore abandoned, and the ore was treated by concentration. Obviously, on ores as high in iron as the Butte ores, the concentrator produces a product that is self-fluxing; in fact, it is possible to produce a concentrate containing more iron than is necessary to flux the silica. Under these conditions, the amount of basic fluxing materials required for the smelting operations became very srnall and the converter slag lost its former value as a blast-furnace flux. For this reason, a less expensive method of recovering the copper, silver, and gold contained in it than smelting in blast furnaces had to be found. It was not feasible

Jan 1, 1921

By Richard L. Ash

7.3-1. Introduction. All phases of mining competent materials are affected directly by the results achieved from primary blasts. It is imperative that their design suit each particular set of mining conditions. In general, the round design must provide an adequate tonnage of material, properly placed with suitable fragmentation, to ensure that loading, haulage, and subsequent disposal or processing are accomplished at the lowest possible cost. Blasting rounds are designed by the proper application of cratering relationships developed for the single, concentric, confined explosive charge. Blasting for surface mining and most open-cut heavy construction, however, is characterized by the use of rounds, composed of a number of explosive charges with relatively long lengths, which are placed in benches with specific finite dimensions. Therefore, modifications must be made to the classical, single point-charge cratering concepts. It is the purpose of this discussion to outline the basic principles, significant variables, and procedures for their integration in the design of rounds that are applicable to conditions characteristic of surface mining. Because relatively insensitive blasting agents will be used in most instances, particular attention must be given to priming, control of confinement, and selection of charge diameters that ensure complete explosive-reaction execution. 7.3-2. General Considerations. The primary requisites for any blasting round are that it ensure optimum results for existing operating conditions, possess adequate flexibility, and be relatively simple to employ. It is important that the relative arrangement of blastholes within a round be properly balanced to take advantage of the energy released by the explosives and the specific properties of the materials being blasted. There are also environ- mental and operational factors peculiar to each mine that will limit the choice of blasting patterns.

Jan 1, 1968

By M. Muskat

A theory has been developed describing the behavior of wells and reservoirs producing by the action of bottom water drives. It is assumed that the pressures are maintained above the bubble point, and that the permeability to viscosity ratio of the water in the flooded zone is the same as for the oil in the oil-saturated pay. Accordingly, the treatment is based on the homogeneous fluid potential theory. The effect of the difference in density between the oil and water is neglected. .4fter deriving the proper potential distrihutions, the nature of the rise of the water-oil interface below the producing wells is calculated. The primary clean-oil-production phase is expressed in terms of the displacement efficiency, defined as the fraction of the pay flooded out by the rising water table at tlle time of first water entry. The variation of this displacement efficiency is calculated as a function of the well spacing, pay thickness, the ratio of the horizontal to vertical permeability, and the well penetration. The important parameter, other than the well penetration, is found to be the ratio of the well separation to the thickness of the oil pay multiplied by the square root of the ratio of vertical to horizontal permeability. It was found that the displacement efficiency continually decreases as this parameter increases, and for values of the latter >3.5, the efficiency varies inversely as the square of the parameter. It also increases with decreasing well penetration. Perhaps the most striking result of this phase of the analysis is the conclusion that in order to explain the delay in entry of water in wells producing by bottom water drives for periods longer than a few days normal production, with drawdowns large compared with the differential density head between the oil and water, it is necessary to assume that the vertical permeability is a very low fraction of the horizontal permeability. An analysis is also given of the production history after the water has broken through, on the assumption that the production mechanism and details of the flow distribution continue to be the same as during the phase of clean-oil production. As is to be expected, it is found that the water cut will increase at an accelerated rate as production proceeds. However, the initial differences between systems of different well penetrations or well spacings with respect to the total clean-oil production gradually decrease in terms of the variation of the water-oil ratio with cumulative production. In particular, by the time the water-oil ratio has reached values of the order of 5 or greater the cumulative recoveries will generally differ much less among various producing systems than their corresponding clean-oil recoveries. Introduction On the basis of elementary geological principles, one may classify effective water-drive fields in two groups. In the first, the entry of water into the oil-producing formation may be characterized as an edge-water encroachment. This term is used to suggest that the motion of the water proceeds largely in a direction parallel to the planes of stratification. This type of water intrusion occurs usually in thin producing zones and in strata lying along structural flanks of appreciable dip. In the second group—"bottom water-drive" fields—the water-oil interface lies in a plane of zero or slight inclination to the

Jan 1, 1947

By M. Muskat

A theory has been developed describing the behavior of wells and reservoirs producing by the action of bottom water drives. It is assumed that the pressures are maintained above the bubble point, and that the permeability to viscosity ratio of the water in the flooded zone is the same as for the oil in the oil-saturated pay. Accordingly, the treatment is based on the homogeneous fluid potential theory. The effect of the difference in density between the oil and water is neglected. .4fter deriving the proper potential distrihutions, the nature of the rise of the water-oil interface below the producing wells is calculated. The primary clean-oil-production phase is expressed in terms of the displacement efficiency, defined as the fraction of the pay flooded out by the rising water table at tlle time of first water entry. The variation of this displacement efficiency is calculated as a function of the well spacing, pay thickness, the ratio of the horizontal to vertical permeability, and the well penetration. The important parameter, other than the well penetration, is found to be the ratio of the well separation to the thickness of the oil pay multiplied by the square root of the ratio of vertical to horizontal permeability. It was found that the displacement efficiency continually decreases as this parameter increases, and for values of the latter >3.5, the efficiency varies inversely as the square of the parameter. It also increases with decreasing well penetration. Perhaps the most striking result of this phase of the analysis is the conclusion that in order to explain the delay in entry of water in wells producing by bottom water drives for periods longer than a few days normal production, with drawdowns large compared with the differential density head between the oil and water, it is necessary to assume that the vertical permeability is a very low fraction of the horizontal permeability. An analysis is also given of the production history after the water has broken through, on the assumption that the production mechanism and details of the flow distribution continue to be the same as during the phase of clean-oil production. As is to be expected, it is found that the water cut will increase at an accelerated rate as production proceeds. However, the initial differences between systems of different well penetrations or well spacings with respect to the total clean-oil production gradually decrease in terms of the variation of the water-oil ratio with cumulative production. In particular, by the time the water-oil ratio has reached values of the order of 5 or greater the cumulative recoveries will generally differ much less among various producing systems than their corresponding clean-oil recoveries. Introduction On the basis of elementary geological principles, one may classify effective water-drive fields in two groups. In the first, the entry of water into the oil-producing formation may be characterized as an edge-water encroachment. This term is used to suggest that the motion of the water proceeds largely in a direction parallel to the planes of stratification. This type of water intrusion occurs usually in thin producing zones and in strata lying along structural flanks of appreciable dip. In the second group—"bottom water-drive" fields—the water-oil interface lies in a plane of zero or slight inclination to the

Jan 1, 1947

By A. W. Gauger

WITHOUT QUESTION the Commonwealth of Pennsylvania contains the most remarkable coal deposits of the whole world. Within its borders ,are to be found excellent coals ranging in rank from the high volatile bituminous of the western part of 'the state through the low volatile or semi-bituminous of central Pennsylvania to that aristocrat of solid fuels, anthracite, found in the East. . . . But while other states and even the Federa1 Government have recognized the needs of the coal industry, Pennsylvania has not. Though bituminous coal represents one of the most important industries in the state, far more important in annual productive wealth than agriculture, for example, hundreds, of thousands of dollars have been spent on agricultural research whereas little or nothing has been spent on coal investigation.

Jan 1, 1932

By T. A. Rickard

The Cripple Creek district occupies a cluster of foot-hills on the south side of Pike's Peak and is a portion of an extensive, though uneven, plateau which unites the eastern range of the Rocky mountains with the Sangre de Cristo. It is essentially a small volcanic area, of about 20 square miles, amid the granite of the Front range. But though, when regarded as a rich mining district, it may be considered as an isolated area,* yet, geologically, it is, as Whitman Cross has pointed out, only an outlying portion of a much larger volcanic region, which stretches to the south and west, around Silver Cliff and the Rosita hills, forming the picturesque country cut by the deep cañons of the Arkansas river and its tributaries. The mines are situated amid a volcanic complex, consisting of tuffs and breccias which have been penetrated by an extensive system of dikes and other intrusive masses. The prevailing formation is an andesite breccia, which lies upon the worn surface of the granite and fills the deep basin around a volcanic vent. The breccia, since its deposition, has been broken into by several eruptions of phonolite and, later still, by a series of thin dikes of basalt and other allied rocks of a highly basic composition. The successive sedimentary formatione which, elsewhere in Colorado, lie upon the basal granite, are not represented in the district; whatever sediments were laid down before the volcanic period must have been removed by erosion, and there is very little evidence which affords a datum-line whereby the geological age of the volcanic eruptions can be determined. Whit-

Jan 1, 1901

By R. J. Mechin

TOP-SLICING was introduced in the Pachuca district in 1917 by T. C. Baker, at that time mine superintendent, of the Santa Gertrudis mine. There then existed 1200 ft. (365.7 m.) below the surface, lying between the fourteenth and eighteenth levels (a vertical distance of 108 meters) a block of ore having a length of 295 ft. (90 m.), and an average width of 82 ft. (25 m.) and dipping at an angle of 65°. This block lay in the hanging wall of the vein and consisted of highly altered and fractured andesite, cut through with mineralized quartz stringers. On the foot-wall side, 26 ft. (8 m.) of old filling, left by former operators, was of payable grade. Stoping therein was first undertaken by the square-set filling system, but because of the extremely heavy hanging wall and loose dry filling in the foot wall, all square setting had to be accompanied by spiling, which made the operation exceedingly slow and costly. A system of mining was sought that would eliminate the difficulties inherent to the square-set system in heavy ground and that at the same time would effect the desired economies in mining. After several years, top-slicing has met all the conditions most satisfactorily, so that when similar conditions presented themselves in El Bordo mine, this method was adopted with necessary modifications. El Bordo mine is operated by the Santa Gertrudis company, and is situated about two miles north of Pachuca. Because of the diversity of the orebodies, a number of different mining methods are in use, among them top-slicing.

Jan 10, 1925

By L. D. Ricketts

AN older man looks back, perhaps wistfully, on a long and rather active experience, and possibly a popular and brief glimpse of some contrast between past and present may hold your attention for a few brief moments and prove useful. In the late nineties an engineer was .called on to de- sign and build two copper ore concentrating mills of 400 tons average daily capacity. There were larger mills than this at Washoe and elsewhere, but a 400 ton' mill was a large one as mills went over thirty years ago, and one might say a large mill of those days could crush a ton of copper ore in 216 seconds. In the mills I refer to steel construction and the conveying belts were introduced into the copper industry and rein- forced concrete came shortly after. Since then we in the West have ever been faced with a constantly de- creasing tenor in the grade of our copper ores and a constantly increasing demand for our product, and we have therefore been obliged to call for far larger castings and finished machines than were formerly used. The mechanical engineer has also enabled us to accomplish notable economies in power generation and distribution. Ore handling and crushing have been simplified and through the introduction of reagents to induce physical or chemical reactions, or both, our older methods have been vastly improved or even supplanted by new and better ones and our recoveries greatly improved.

Jan 1, 1929

By Lloyd Emory

THE region known as. Guyana or Guiana stretches along the north coast of South America from the mouth of the Orinoco River in Venezuela to the mouth of the Amazon River in Brazil. Politically, it is divided into British, Dutch, and French Guiana, extend¬ ing into Venezuela on the north and into Brazil on the south. Because the area is within the sweep of the northeast trade winds and of approximately the same latitude, plant' and animal life are fairly uniform throughout. The geology is very similar as far as the northern coast is concerned. The drainage is taken care of by a number of large rivers that flow northward directly into the sea. The Courantyne River, which roughly divides the area into half, is the eastern boundary of British Guiana.1 The lower reaches of this river are also the center axis of an ancient bay that at one time indented the coast-line at this point. The old shore-line and, in fact, successive shore-lines can be traced from near the present coast-line in, the northwest district of British-Guiana, south-east and inland, crossing the Essequibo River near Dahli, the Demerara near Christianburg, the Berbice at the mouth of the Kuruduni River and the Courantyne at Vaka-Kuyaha Falls. The line then swings around to the northeast and again approaches the coast near St. Lau-rent in French Guiana. This article will be confined to British Guiana and largely to the valley of the Demerara River, but for geographic names .and topographic details it might, however, apply to Dutch Guiana as well. British Guiana, which comprises about 90,000 sq. mi. and is as large as England, Scotland, and Wales combined, may be divided into three belts, the alluvial belt or coastal plain, the foot-hill area (often spoken of as the sand clay belt), and the hinterland.

Jan 1, 1928

By James M. Stapleton

It has long been recognized by blastfurnace men that correct top distribution of materials is very important in efficient and economical furnace operation. Thousands of experiments on top design, filling, sizing, and other operations have been carried out to improving furnace performance by securing uniform distribution. Many of these experiments have worked out satisfactorily and have been passed along to the industry. Many of them have been discarded and forgotten. It has been the custom to judge the results of such experimentation by the results shown in improved or lowered furnace efficiency. While the effect on furnace practice will have to continue to be the final criterion of experimental changes, it has always been a desire of blast-furnace men to ascertain the reason for failure or success. Efficiency in the blast furnace approaching the maximum can be measured in several ways: (1) by actual operating results as revealed in the coke rate and tonnage figures, and (2), in the degree to which the top gas approaches the limiting ratio of CO/CO2 for the reduction of iron oxide by CO gas. This ratio is shown in the equilibrium curve in Fig. I for the system Fe-O-C and CO2-CO-C. The closer the top gases approach this limiting ratio (set at 1.08 by Martin1 because of the effect of limestone calcination) the more efficiently we may expect a furnace to operate. The fact that low CO/CO2 ratios parallel eficient operating performance caused us to investigate the cause of good or poor distribution and the effect of filling and other changes on furnace operation. Heretofore it has been possible to take a sample of furnace gas (usually from the dust catcher) and from it determine how closely the reducing gases were to the ideal or limiting value as set by the equilibrium diagram. However, to find just where in the top area the distribution was distorted and the top-gas CO/CO2 ratios were distant from equilibrium values has been a difficult and expensive investigational procedure. In an effort to overcome this difficulty, apparatus was designed to take gas samples and temperatures across the top radius of the furnace. It was hoped that with the aid of this apparatus traverse sampling of the ascending gases could be simplified, and the cost of sampling substantially lowered. Routine experimenting could then be maintained and results checked with furnace operation. It must be emphasized that a traverse sampling is necessary for a true picture, as single samples at any one point are unreliable. This statement can be verified by an examination of Tables 3 to 6, showing results obtained at our furnaces in a large number of tests. Apparatus The design of the equipment for taking the samples was governed by the need for providing a simple, routine test that could be performed fairly quickly without adversely affecting normal furnace operation.

Jan 1, 1943

By James M. Stapleton

It has long been recognized by blastfurnace men that correct top distribution of materials is very important in efficient and economical furnace operation. Thousands of experiments on top design, filling, sizing, and other operations have been carried out to improving furnace performance by securing uniform distribution. Many of these experiments have worked out satisfactorily and have been passed along to the industry. Many of them have been discarded and forgotten. It has been the custom to judge the results of such experimentation by the results shown in improved or lowered furnace efficiency. While the effect on furnace practice will have to continue to be the final criterion of experimental changes, it has always been a desire of blast-furnace men to ascertain the reason for failure or success. Efficiency in the blast furnace approaching the maximum can be measured in several ways: (1) by actual operating results as revealed in the coke rate and tonnage figures, and (2), in the degree to which the top gas approaches the limiting ratio of CO/CO2 for the reduction of iron oxide by CO gas. This ratio is shown in the equilibrium curve in Fig. I for the system Fe-O-C and CO2-CO-C. The closer the top gases approach this limiting ratio (set at 1.08 by Martin1 because of the effect of limestone calcination) the more efficiently we may expect a furnace to operate. The fact that low CO/CO2 ratios parallel eficient operating performance caused us to investigate the cause of good or poor distribution and the effect of filling and other changes on furnace operation. Heretofore it has been possible to take a sample of furnace gas (usually from the dust catcher) and from it determine how closely the reducing gases were to the ideal or limiting value as set by the equilibrium diagram. However, to find just where in the top area the distribution was distorted and the top-gas CO/CO2 ratios were distant from equilibrium values has been a difficult and expensive investigational procedure. In an effort to overcome this difficulty, apparatus was designed to take gas samples and temperatures across the top radius of the furnace. It was hoped that with the aid of this apparatus traverse sampling of the ascending gases could be simplified, and the cost of sampling substantially lowered. Routine experimenting could then be maintained and results checked with furnace operation. It must be emphasized that a traverse sampling is necessary for a true picture, as single samples at any one point are unreliable. This statement can be verified by an examination of Tables 3 to 6, showing results obtained at our furnaces in a large number of tests. Apparatus The design of the equipment for taking the samples was governed by the need for providing a simple, routine test that could be performed fairly quickly without adversely affecting normal furnace operation.

Jan 1, 1943

By C. WIFLARD HAYES

(New Haven Meeting, February, 1909.) I DESIRE to make it perfectly clear at the outset that I fully realize the hazardous nature of any attempt to estimate the quantity of iron-ore or any other mineral in the ground. I should not have had the temerity to venture upon an inventory of the iron-ore supplies of the United States except for the requirements of the Conservation Commission. During the preparation of this inventory I have been impressed by the wide diversity in estimates of those best qualified to. hold an opinion, and I am therefore prepared in advance for criticism of my figures. Inasmuch as this report was prepared in large part for unprofessional readers, I considered it necessary to classify and describe the commercial iron-ores in a somewhat elementary manner, in order to explain the reasons for the large element of uncertainty in the estimates. I have therefore given a chemical and a geological classification of iron-ores, which place the commercial deposits in six classes: (1) magmatic segregations in basic igneous rocks; (2) contact-deposits formed in connection with igneous intrusions; (3) concentration-deposits; (4) replacement-deposits; (5) bedded-deposits, and (6) gossan-deposits. The iron-ores are further distinguished under two classes available and not available. This classification is in large measure arbitrary, and it, is evident that it will vary front time to time. In the available class are placed those ores which can be worked at a profit under conditions essentially as they exist at present. Since it depends wholly on the question of costs, the various factors which affect cost will determine the classification of any particular deposit. Actual production, * Abstract of Report prepared for the Conservation Commission. t Chief Geologist, United States Geological Survey. .

Apr 1, 1909

This discussion was prepared by members of the Phelps Dodge Corpn. staff who were designated to review the minutes. It is confidential but permission has been granted to distribute copies among those who attended the Conference. The minutes of the above conference contain numerous references to the plants and practices of Phelps Dodge Corporation. As many of these references are inaccurate, the following notes are made covering such points: Construction Magnesite Brick in Reverb. Arch (1) An.18" arch, 20 feet long, was built on one furnace with 5 feet on each side of magnesite brick, the center portion .being of silica brick. The furnace was put in operation February 13, 1930 and on April 23rd after 68.8 days' operation it was replaced due to failure of the silica brick forming the center of the arch. At this time, while the silica brick had completely gone, there was 14" of magnesite left. Bridgewall Tapping (2) Tapping matte through the burner wall was first tried at the Copper Queen Smelter in April, 1925. At that time, a copper casting with 1 ½ extra heavy pipes for water cooling cast in it, and having one taphole block was used. Later, on the other (old) furnaces, similar castings, but equipped with two tapholes, were used. We found with these furnaces that we could tap through the burner wall at the beginning of a campaign, but would subsequently have to go back to side wall tapping. This was the case until sometime in 1926. The new furnaces, that went in operation at the beginning of 1927, each had water. cooled castings with two tapholes. These have been used entirely and have been quite successful. Sometime after the furnaces were put into operation sidewall tapholes were put in, simply for the removal of any accumulation of matte that might be temporarily retained at the front end by bridges or dams in the furnace formed by overcharging locally.

Jan 1, 1930

Edward Halse, Puerto Berrio, Colombia, So. Amer. (communication to the Secretary*): The Taviche mining-district is generally known as " Taviches," being named from the two villages called respectively San Pedro Taviche and San Jero-nimo Taviche. It is so called by Jose G. Aguilera, in his paper on the Geographical and Geological Distribution of the Mineral Deposits of Mexico;' and in published reports by the late N. W. Rudston Read ;2 and by Juan de Dios Villarello3 The region is a large one, measuring about 24 miles long and 7 miles wide. Dr. Chance, in his interesting paper, tells us very little about the nature of the ores, and, with regard to the geology of the district, contents himself with observing that " the country, as a rule, consists of eruptive rocks; and no evidences of sedimentary strata appear near the mines." The latter part of the above statement is hardly correct. The formation is mainly

Jan 1, 1906

By J. C. Reed

CINNABAR was discovered in southwestern Arkansas on Little Missouri River in sec. 1, T.7S., R.26W., in April, 1930, and near Antoine Creek in sec. 28, T.6S., R.23W., some 15 miles farther east in May of the same year. It was not, however, until June, 1931, that cinnabar was identified as such in a specimen from the original discovery area sent to W. M. Weigel1 by Walter F. Hintze of Murfreesboro. Almost simultaneously2, in July, 1931, Moritz Norden of Hot Springs identified specimens from the Antoine Creek area as cinnabar. Immediate interest in the district followed the identification of cinnabar and by January, 1932, the district was known to extend as a mineralized belt about one mile wide trending east-northeast from sec. 13, T.7S., R.27W., in Howard County-across central Pike County and into Clark County to sec. 19, T.6S., R.23W., thence extending southeast into sections 33 and 34 of the same township. Since then, cinnabar has been found in sec. 6, T.7S., R.22W., thus giving a total east-west length to the district of approximately 30 miles. Interest focused mainly on the two discovery areas, with the result that mining development has progressed most rapidly in those localities. In the Antoine Creek area the Arkansas Quicksilver Co. has done con-siderable exploration work and has retorted the high-grade ore so .obtained. In the Little Missouri area the Southwestern Quicksilver Co. has had a 12-ton rotary furnace in more or less continuous operation since April, 1932, and has been the largest producer in the district.

Jan 1, 1935

By G. Derge, W. Peifer, J. H. Richards

INTRODUCTION A WIDE variety of metallurgical defects in steel have commonly been attributed to the presence of excessive amounts of hydrogen. These defects include flakes in rails and forgings, cracks in welds, and blisters in enameled ware. They have been related to hydrogen largely by circumstantial evidence because the proper sampling and analysis of steel for hydrogen has been known to be difficult and because no general agreement has existed with regard to the relative suitability and accuracy of available methods. The need for a direct approach to these problems has been widely recognized. This general situation has been well described in the publications of the British Committee on the Heterogeneity of Steel Ingots,1 and current approaches to the problem were reviewed in a recent symposium of the AIME.12 The plans described by the present authors at that meeting have now matured satisfactorily and will form the basis of this paper. The principle object of this paper will be to describe the methods of sampling and analysis which have been developed and to illustrate the usefulness and limitations of these methods by citing their application to a specific problem. The first problem selected for investigation was the behavior of hydrogen in rail steel. This was chosen because the occurrence of shatter cracks in rails has received a great deal of study over a long period of time. The defect can be controlled by the expensive procedure of slow cooling. However, it may be hoped that a better understanding of the factors influencing the hydrogen content of rails will lead to a more efficient control of this problem. Rails provide a good starting point for a more general study of hydrogen in steel because they provide a cross section large enough to develop cracks, yet small enough for convenient handling and sampling. Rails were also selected because they are made from plain carbon steel and it was felt that the initial work should not be complicated by the effects introduced by alloying elements. The considerations which determined the original planning of this study should be reviewed. The inherently complex nature of most hydrogen problems requires that a large amount of data must be collected for any particular case. This in turn means that any analytical procedure should be as rapid and simple as possible. The same objective of speed is indicated by the fact that it may finally become desirable to use hydrogen analysis in process control. It is also known that hydrogen is highly fugitive and that any procedure which facilitates early analysis of the sample without prolonged or irregular storage has distinct advantages. The most important previously reported methods of analysis may be classified into three general groups: (I) Vacuum fusion. (2) Vacuum extraction (without melting). (3) Total combustion.

Jan 1, 1948