Search Documents

By Martin E. Chenevert

The early work of Terzaghi1 showed that the true stress state of a rock can be expressed by the principle of effective stress. This principle states that effective stress is equal to total applied stress minus the pore pressure. Since the introduction of this principle, a great effort has been made to measure the pore pressure of rocks so that the true stress state can be determined. For clean, permeable sandstones, it is usually found that the effective stress principle can easily be applied. Direct measurement of the pore pressure is achieved with a hydraulic pressure device and the effective stress state thereby computed. However, for fine-grained rocks which contain large amounts of clay (referred to herein as shales), pore pressure measurements are usually quite difficult because of the adsorptive forces of the clay platelets, which produce negative internal pressures. No suitable device is known for measuring internal pressures of dry shales; the effective stress approach is therefore not feasible and data are usually presented in another form. As an example, data from compressive strength tests are presented as a function of rock wetness, rather than effective confining stress. The work of Belopoloskii2 and Colback and Wiid3 are examples of such data. It was pointed out by Lambe and Whitman4 that a better way must be found to express the effective stress of argillaceous rocks. The information presented herein is an attempt to fill that need. Various authors have been able to measure moderate negative pore pressures (0-240 psi) within rather wet, argillaceous rocks by means of various pore pressure devices. In 1961 Lambe5 resented information which shows that pore pressures in argillaceous rocks are indeed negative ; he presented values of suction pressure as low as - 14 psi. Likewise,

Jan 1, 1970

By T. A. Read, H. K. Birnbaum

STRESS-induced twin boundary motion in the AuCd ß'phase (52.5 at. pct Au 47.5 at. pct Cd having an orthorhombic structure (space group D h)' was discussed for the case of transformation twins.' Mechanical twinning, i.e., introduction of new twin orientations by the applied stress was sometimes observed in the ß' phase which contained two transformation twin orientations. (See Ref. 2 for experimental details.) The transformation twins terminated at the mechanical twin boundary; the two initial orientations having been twinned to the new orientation as shown in Fig. l. In a "hard" tensile instrument, formation of each mechanical twin was accompanied by a sharp drop in load (and an audible click) resulting in a typical serrated load-extension curve. The mechanical twins increased in width and additional twins were nucleated as the load increased until the entire specimen was occupied by the mechanical twin orientation. A restoring force2 caused the mechanical twin and transformation twin boundaries to return towards their initial configuration on releasing the load. In a stabilized specimen* the total strain introduced by mechanical twinning was recovered on releasing the applied stress. Initial and final microstructures were identical. After decreasing gradually to a critical width, mechanical twins suddenly disappeared accompanied by audible clicks and sharp increases in load (measured at a constant rate of crosshead motion in a "hard" machine). Mechanical twins could be stabilized in any position by maintaining the applied load for a sufficient time, indicating a decrease in restoring force with time similar to that observed for transformation twins.' Orientation relationships for mechanical and transformation twins were determined and are shown in Fig. 2. The mechanical twin, T3, was twin related to transformation twin, T,, by reflection in (1ll), and twin related to transformation twin, T2, by reflection in (111)T, . T, was related to T, by reflection in(ll1)T1 . The "average" mechanical twin composition plane lay several degrees from (1ll), . In every specimen which mechanically twinned, orientation T3 was most highly favored by the applied stress, i.e., it was the twin orientation which provided the greatest change in length compatible with the direction of applied stress

Jan 1, 1961

By C. G. Dunn

WITH respect to theories of recrystallization in metals plastically deformed, it has been said that the present status of this subject is far from satisfactory.1 It may also be said that before any mechanism of recrystallization for metals and alloys can be set forth in a satisfactory manner, there must be made available considerable data on orientation changes that occur during the deformation and recrystallization processes. Although extensive data have been published on recrystallization in single crystals and in polycrystalline specimens, more results of a type that can be classified according to simple orientation changes would be desirable in this complex field. It might even be said that before classifications are made according to types of orientation changes, it may be possible to classify a considerable amount of data into certain kinds of orientation states if groups of common or nearly common orientation occur. Methods for computing the probability of occurrence for various types of groups have been published2 and it has been pointed out in particular that it should be possible to analyze orientation data for high-order twin relationships between old and new grains even when agreement is not at all exact. In this connection, work on recrystallization in silicon ferrite reported in a paper concerned with complex groups of annealing twins' indicated that some data were consistent with primary nucleation occurring according to a second-order or a third-order twin transformation. However, further work in this latter direction was definitely needed. It is, therefore, the purpose of the present paper to report data and analyses for primary nucleation in silicon ferrite following small deformations that have been carried out at the Pittsfield Works' Laboratory of the General Electric Co. Analyses have been made with the aid of standard groups of twins that are reported elsewhere .4 PREPARATION OF SPECIMENS AND EXPERIMENTAL PROCEDURE The material used in the present investigation was taken' from the same heat of steel as that used in a prior report.3 The finished strip in both cases was made by the Allegheny-Ludlum Steel Corporation according to methods that produce a high degree of preferred crystal orientation. Samples with large grains had the following composition: 3.45 per cent Si, 0.003 C, 0.008 P, 0.020 S, 0.075 Mn, 0.031 Al and 0.072 Cu. Thickness of specimens was 0.012 inches. Plastic deformation was produced by cold-rolling the samples on a mill with

Jan 1, 1945

By F. F. McINTOSH

STEEL is a general name applied to the alloys of iron and carbon. These alloys always contain , other elements such as manganese, silicon, sulfur, and phosphorus. Manganese and silicon are usually considered to be alloying elements. Sulfur and phosphorus are regarded as impurities. Tradition has damned them both and, in addition to classifying them as impurities, has established the general impression that many of the ills of steels are the result of the presence of one or both of these elements. Metallurgists are inclined to question the soundness of this tradition. The fact that one blast-furnace plant is devoted entirely to the production of ferro-phosphorus which is used to rephosphorize basic open-hearth steel, and that sulfur is added to many heats of steel, indicates that these so- called impurities might also be classed as alloying elements, and that the tradition which damns them may not be altogether fair and well founded. A critical search through the technical literature on the effect of phosphorus on steel will disclose many references to its harmful effect. Most of these are general in character, but there has been a strong tendency to accept this traditional belief in the harmful effect of the element.

Jan 1, 1926

By F. C. Langenberg

IT is the purpose of this paper to present a limited amount of experimental data obtained on the Charpy impact machine. Several concrete examples will be given showing the relation existing between the results obtained upon the Charpy impact machine and the behavior of the parts tested when in service. Although it is pointed out by G. Charpy and A. Cornu-Thenard1 that it is first necessary to determine a satisfactory working process before studying the correlation between the results of these tests and the behavior of the parts tested in service, this ideal course cannot be strictly adhered to. If a certain part repeatedly fails in service and the available tests give no indication of its cause, advantage must be taken of any possible means that will solve the problem; therefore, even though the reliability of the results obtained by the Charpy impact machine have been questioned by many, it was necessary to use this instrument without giving careful consideration to its possible sources of error. It would seem that the conclusions arrived at by Charpy and Cornu-Thénard justify the assumption that the precision obtained by this machine is comparable to that obtained by, the other more common forms of testing. The second general conclusion arrived at by them, namely, that the impact test upon notching does not offer any direct correlation to the ordinary tests, is also borne out by many hundred determinations made in the laboratories at Watertown Arsenal. This statement, however, should be qualified as follows: Other ordinary tests include the static tensile test from bars taken in a longitudinal .direction and the Brinell hardness. The author agrees that no law is yet known for the computation of the energy absorbed in the rupture of bars of the same material but of different dimensions. Although Charpy and Cornu-Thénard do not refer in their valuable article to the use of the Charpy machine in industrial practice, it should be stated that this instrument has been in constant use in the laboratory at Watertown Arsenal for several

Jan 8, 1919

By F. S. Young, K. E. Gray

Drilling tests with a 11/4-in. diameter roller bit were performed on Berea and Bandera sandstones and Leuders limestone using water and two conventional drilling muds as circulating fluids to evaluate the influence of dynamic filtration on penetration rate. The muds possessed widely differing API fluid-loss properties. Mud filtrate was constrained to flow beneath the bit; no filtrate flowed radially through the borehole wall. Rock pore pressure at three different locations ahead of the bit, cumulative filtrate volume, borehole pressure and bit location were monitored during drilling. The rock samples, cored in three orientations with respect to bedding planes, possessed a wide range of liquid permeabilities. and were drilled at borehole-to-formation pressure differentials of 0, 250, 500 and 1,000 psig. The effect on penetration rate of API fluid loss, borehole pressure and rock permeability was studied. Rock permeability damage and pore pressure gradients beneath the bit were evaluated. The importance of borehole-to-formation pressure differential was illustrated for each drilling fluid and rock permeability combination. Penetration rates decreased with increased borehole pressure and reduced fluid loss. The observed penetration rate reduction due to changing fluid Ioss was attributed to decreased filtrate flow and improved mud cake plastering hy the low fluid-loss mud. The reduction in filtrate flow could not be related to spurt-loss phenomena. Rock permeability influences penetration rate through particle invasion ahead of the hit, which damage leads to high pressure gradients. Penetration rate variance with sample orientation was evident for water-drZled samples but less obvious for mud-drilled rocks. Permeability damage beneath the bit ranged from 1 to 3 cm. Maximum damage occurred in the first 0.1 cm. Pressure gradients varied with API fluid 10.s.s and could be correlated with penetration rate. The pressure gradient was found to influence penetration rare in rocks of all permeabilities tested. INTRODUCTION Early microbit and small-scale drilling experiments proved to be invaluable contributions to understanding the mechanics of drilling at depth. For example, the effect of borehole-to-pore pressure differential on drilling rate was demonstrated conclusively by Murray and Cunningham', Eckel' and others .' However, the effects of various drilling fluid properties on drilling rate, particularly filtration, have not been studied extensively on a laboratory basis. Microbit correlations of penetration rate with different viscosity and API fluid-loss muds led EckelV o conclude that viscosity and density. more than API fluid loss, were the most important fluid properties in controlling drill bit penetration rates. Ferguson and Klotz6 studied filtration beneath the bit and stated that the maximum amount of filtrate which could conceivably flow beneath a drilling bit could be described by a potential function associated with flow from a moving disc source. and be characterized by a depth-of-filtrate invasion. Invasion depth is a function of penetration rate, formation porosity and permeability, flooding efficiency, pressure difference between borehole and formation and borehole radius, assuming that no filtrate flows through the borehole walls. Electric analog and experimental measurements were obtained, assuming no plugging of the formation pores. Theoretically, filtrate invasion was predicted to extend from 1- to 15-hole radii beneath the cutting surface; experimental results indicated that the extent of invasion was only Y2 in. Comparing these data with results of core-plugging experiments by Norwak and Krueger' led Ferguson and Klotz to state that the drilling operation apparently contributes to higher filtration rates than are observed in nondrilling core filtration tests in which the core face is jetted and scraped. Glenn and Slusser: in describing a linear filtering system in which a rotating bit continuously scraped mud cake from the surface but did not penetrate Alundum cores, stated that mud-solids invasion and permeability damage of the cores were most severe in the first 2 to 3 cm. The filtrate flow rate through the core was found to stabilize after sufficient time had elapsed for the formation of an internal mud cake whose effective permeability was estimated to be 50 to 300 times as high as that of bulk filter cake. Krueger and Vogel reported core permeability damage depths up to 12 in. during a 5-day exposure period in which filter cake buildup was prevented. Havenaar pointed out that the discrepancy between reported and calculated values of filtrate volume obtained in the experiments of Ferguson and Klotz was due, among other things, to failure of the reported API fluid loss to truly represent filtration beneath the bit. Williams," Pro-koplz and others"" have shown that dynamic filtration tests (where a flow of fluid parallel to the filter surface continually erodes the deposited filter cake until a dynamic equilibrium between wall-shearing forces and normally directed compaction forces is attained) yield higher filtration rates than do static tests. Cunningham and Goinss reported results of drilling tests in impermeable shales. They found that by reducing

OFFICERS AND COMMITTEES OF LOCAL SECTIONS AIME Committee on Local Section Affairs Roger Pierce, Chairman Carleton C Long Thomas C Frick AIME Committee on Student Chapter Affairs John P Nielson, Chairman John C Calhoun, Jr J R Van Pelt, Jr Council of Section Delegates A A Burr, Chairman (Hudson-Mohawk) Ralph A Watson, Vice-Chairman (North Pacific) L G Neely, Secretary (West Central Texas) INTERIM COMMITTEE M O Langham (East Texas), Fulton J Olivier (Delta), L W Smith (Niagara Frontier), G R Spindler (Central Appalachian) LOCAL SECTIONS (There are 78 Local Sections in the United States, 9 Foreign) ADIRONDACK Established June 18, 1952 Official year begins in April Meets fourth Saturday monthly, April through October Seven meetings annually Local Section Dues AIME Members $2, Nonmembers $3 Charles F Dievendorf, Chairman Severn P Brown, Vice-Chairman George E Erdman, Secretary-Treasurer Gouverneur Talc Co , Inc Gouverneur, N Y Malcolm V Lowry, '60, Section Delegate Committees Membership David J Crawford, Chairman Program Brower Dellinger, Chairman Student Affairs Eugene A Eastman, Chairman

Jan 1, 1959

By S. C. Termes, R. L. Wilfong

As part of an effort to provide basic data on the fundamental scientific and engineering principles of minerals beneficiation, the Bureau of Mines is conducting research on the flocculation of mineral fines. This paper presents results of studies using cross-linked starches containing carboxyl, diethanolamine, iminodiacetic acid, and xanthate groups to flocculate hematite, goethite, chromite, manganite, pyrolusite, cuprite, and cassiterite fines. The carboxyl and xanthate derivatives flocculated all minerals except cassiterite; the latter was flocculated by only the diethanolamine derivative. The imlnodiacetic acid derivative flocculated hematite, goethite, chromite, cuprite, and pyrolusite fines. Zeta potential measurements were made to help define the reaction mechanism responsible for flocculation. These measurements indicate that electrostatic attraction probably is not involved, except possibly in the case of the diethanolamine derivative. The separation of hematite from quartz by selective flocculation with chelating crosslinked starches under two pH conditions and with two dispersing agents is described. Best recoveries and grades were found when either the carboxyl or xanthate derivatives was added at the natural pH of the pulp in the absence of a dispersing agent.

Jan 1, 1984

By R. D. Russell, R. M. Farquhar

ISOTOPIC tracers have become an important aid in following the progress of chemical processes in the laboratory. It has recently been found possible to utilize a system of naturally existing isotopic tracers to obtain information about the geo- logical history of lead ores. Common lead, such as is found in lead deposits, is a mixture of four stable isotopes having atomic weights 204, 206, 207, and 208. Of these, the last three are identical with the lead isotopes produced as stable end products of the radioactive decays of uranium and thorium: the first, lead-204, is not known to be produced on the surface of the earth by any process. Since uranium and thorium occur in the surface regions of the earth in amounts comparable with lead, and since the half-lives of uranium and thorium isotopes are of the same order as the age of the earth, they produce the radiogenic lead isotopes in amounts com- parable to the amount of nonradiogenic lead present. Every significant exposure of a sample of lead to uranium and thorium will therefore lead to the permanent alteration of the lead isotope ratios in that sample.

Jan 5, 1957

Detailed Geology of Certain Areas in the Mineral Hill and Warm Springs Mining District. By A. L. Anderson. T. H. Kilsgaard and V. C. Fryklund. Jr. Idaho Bureau of Mines and Geology. University of Idaho. 73 P. Maps, Illus.-Divided into three parts, this pamphlet covers the geology and ore deposits of the Hailey-Bellevue Mineral Belt, the Triumph-Parker mine mineral belt, and the ore deposits of the Mayflower Area. Numerous maps and illustrations are included for each area. Government Administration of the Copper Industry, World War 11. By John W. Douglas. 1950.51 P. $1.-This pamphlet covers in detail all the steps relating to control and operation of copper and copper products, and is of particular interest to primary producers, brass mills, wire mills, and foundries. Of particular current interest is the booklet's coverage of the steps leading to the Controlled Material Plan, into which industry is now once again heading. Copies can be obtained for $1 from John W. Douglas, Republic Foil & Metal Mills Inc., 55 Triangle St., Danbury, Conn.

Jan 12, 1951

By L. Bombardieri, H. F. Mills

Iron King mine, producing gold-silver-lead-zinc-ore, is 10 miles east of Prescott, Ariz. At present the 1806 level is being developed. The echelon pat tern of ore deposit continues at depth but is less pronounced, and the orebody is now more or less continuous over 2600 ft of strike length, with widths 5 ft to as high as 26 ft where overlapping of lenses occurs in one section of the mine. Better continuity of ore at depth has encouraged systematic mining and improved plant facilities to offset higher operating costs. With favorable persistence of ore at depth, the three-compartment No. 6 hoisting shaft appeared inadequate to handle increased tonnage from greater depths, and in 1952, a four-compartment steel and concrete shaft was started. This is now at a depth of 1906 ft, and shaft pockets and loading cartridges are being installed on the 1806 level. Ore from the new shaft, hoisted in 5 ½ -ton Jeto bottom dump skips, is dumped into a 500-ton shaft bin, from which it is fed to a 16x30-in. gyratory crusher and conveyed 415 ft through an undersurface concrete gallery to the secondary crusher and conveying system supplying the 900-ton mill. Lead, zinc, and pyrite concentrates are floated, and the flotation tailings are cyanided after desliming. Waste from the new shaft is dumped into a 250-ton surge bin, fed from this bin to a 24-in. conveyor, and discharged into the glory hole above the block cave. The new shaft is served by a double-drum 400-hp hoist used for ore and waste; the No. 6 shaft conveys men and material.

Jul 1, 1956

By F. Keller

SOME PHRASEMAKER has aptly said that nature made aluminum light but research made it strong. Research has been a vital element in the past progress of the aluminum industry and its future growth likewise depends upon the application of the results of research. The role of aluminum products in World War II is well known and this metal will certainly be increasingly important in the postwar world. Some of the principal developments in the war years were in the field of high-strength aluminum alloys. New and stronger alloys were developed which enabled designers to get increased speed and performance in our fighter planes and bombers. The aircraft industry will continue to use these new materials for peacetime passenger and cargo airplanes. High-strength alloys will also find structural applications in trucks, buses, trains, ships, and bridges.

Jan 1, 1946

By E. W. Enqelmann

DURING January, 1933, burlap or coco matting was placed in the bottom of launders handling various products of the flotation plant of the Magna mill of the Utah Copper Co., with the hope of increasing the total recovery of gold. This was soon followed by placing various materials, such as coco matting, cotton twill, and common 10-oz. burlap on the bottom of the main tailing launder. The burlap was found to be the most economical material to use. The test was first conducted in an old wooden launder, 40 in. wide and 2000 ft. long, with 10-oz. burlap fastened

Jan 1, 1935

By James W. Wade

THIS discussion of the future supply of lead refers only to the next ten-year period. Beyond that no prediction can be made that would be of sufficient accuracy to serve any purpose. When any commodity is by an unsatisfied demand forced to a higher price level, and the profits of those who are able to produce the commodity are greatly increased, there is awakened a new interest in the commodity on the part of both producer and consumer. The consumer attempts to reduce his costs by developing substitutes or assisting in the development of new sources of supply. Lead is now going through this stage. The lead producer is increasing development expenditure and searching for new mines. The consumer is developing substitutes as illustrated by the increasing use of zinc oxide as a pigment, and the use of dry batteries in radio sets. The search of the Ford interests for lead, by prospecting in Missouri and Idaho, is induced by the effort to develop a new source of supply. Considering the index figures of the Department of' Commerce, it is evident that lead is on a substantially higher price level. For February, 1926, the index figure of lead is 209, while the general commodity price index is only 156, 100 being taken as the base for 1913.

Jan 1, 1926

By Carl Zapffe

JUST as 85 per cent of the total ore produced annually in the United States comes from the Lake Superior region, so does one of its six producing districts-the Mesabi --dominate that region both as to production and total reserves; also in ore Treatment, Mesabi practice is dominant. Therefore, in discussing future reserves or ore treatment one may visualize one big district with five smaller districts as so many satellites. In considering the future less thought need be given to processes than to, economic policies. For thirty years experimental work has now been in progress and every possible ore-treatment process now known has been given attention. This work was started when there was no recognizable danger of running short of ore because of rapid consumption. Thirty years ago the annual production had just progressed beyond the twenty-million bracket for the first time. Today fifty million tons is considered a small production, and last year the aim was for 65 million. At the recent rate of production the life of the estimated reserves of good ore is about 35 years. All who know the local terrain are convinced that, unlike thirty years ago, the chances for discoveries of new big deposits are nil; treatment of lean ores obviously is to become an all-important topic.

Jan 1, 1938

By Sadtler, C. B.

IT is generally assumed that in most metals and alloys a given tensile stress produces a given deformation irrespective of the length of time during which the stress is applied. This assumption is justified in most of the important engineering applications of metallic materials; however, in the case of some metals and alloys used or tested at temperatures over or slightly under that at which recrystallization can occur the assumption is not warranted.1 This paper deals with the variations of deformation produced by a constant tensile stress acting for varied lengths of time in the special case of thin aluminum alloy sheet of the duralumin type, which had been subjected to different thermal and mechanical treatments. The material investigated was in the form of a sheet approximately 0.002 in. thick, which had been cold-rolled from a thickness of 0.020 in. It has been found that at a sufficiently high constant tension such material deforms continuously with the elapse of time and that the rate at which this deformation occurs is greatly influenced by the previous thermal and mechanical treatments.

Jan 1, 1927

IN speaking, on the subject, "Engineer-Citizens," at the Lehigh Valley Mineral Industries Conference dinner, on April 26, at Easton, Pa., George Otis Smith, Director of the United States Geological Survey and President of the American Institute of Mining and Metallurgical Engineers, said in part: "It would be carrying coke to Connellsville to bring to the Lehigh Valley the idea that mineral resources are the foundation of national prosperity. Unfortu-nately, however, this obvious, fact is not everywhere recognized. Too many of our economists, journalists, statesmen and other dopesters of present business con-ditions stress the human factor so strongly that they overlook the material with which men work out their destiny. To them the financial psychology of Wall Street and the political logic of Capitol Hill and the business commonplaces of Main Street all loom far larger than the geology of the Lehigh Valley or the engineering triumphs of Bethlehem, or, the creative thinking at Lehigh and Lafayette. "The present situation in the industrial and .business world is a complex of interacting causes and reacting effects not easily itemized and entered on our trial balance sheet. But, chief among the liabilities of today is the excess of production capacity in most branches of industry. The farmer has no. monopoly in his desire for relief. Whether your professional connections are with steel or cement, coal or oil, copper, or zinc, you; know too well that for, the moment America is over-engined, and you keenly realize the ever-present hazard of industry speeding up regardless of the curves or grades just around the corner.

Jan 5, 1928

By B. W. Frazier

At a recent meeting of the North of England Institute of Min ing and Mechanical Engineers, during a discussion upon the com pression of air, attention was called to an apparent anomaly in the phenomena attending the compression. At a subsequent meeting this apparent anomaly was explained by Prof. Herschel, and all the facts observed shown to be strictly in accordance with the laws of thermodynamics. Upon reading the report of the discussion in the published transactions of the society, it occurred to me that an attempt to determine mathematically the amounts of energy (whether in the form of heat or of work) expended and absorbed in compressing air, and causing it to perform work by expansion, might prove of use to some who have not access to any treatise upon the application of the laws of thermodynamics to the compression of air, and who have not the time or the inclination to make such application for themselves. The apparent anomaly noticed was this: If air be compressed, and at the same time, by the sufficient application of a cooling medium, kept at a constant temperature, the indicator diagrams in the

By J. M. W. Mackenzie

A microelectrophoresis technique has been used to measure the zeta potential of quartz over a range of pH and ferric iron concentration. The results have been discussed in terms of the adsorption of ferric cations and ferric hydroxide to the quartz surface. Possible relationships between the experimental results and the flotation of quartz have been examined. The adsorption of multivalent cations at the surface of quartz has been studied by many investigators who have used a variety of experimental techniques ranging from streaming potential 1 to radiometric2 measurements. Two possible mechanisms of cation activation of quartz have emerged from the results of these investigations viz: the adsorption of the cation to the negatively charged quartz surface, followed by adsorption of the collector anion to the adsorbed cation site, or: formation of a cation-collector complex which is then adsorbed to the quartz surface. In many natural and industrial systems one of the most prevalent activating species for quartz is ferric iron, this is especially so in the acid-circuit, anionic flotation of iron ore. The adsorption of ferric iron to the quartz surface is complicated by the ability of ferric iron to form complexes with anions, a phenomena which is of minor importance in one of the most widely studied quartz activation processes, ca ++ activation.* *The pK value for [ca(oH)+]/ [ca2+] [oh-] is 1.46 indicating that the influence of Ca (OH)+ ions will be minor in all but strongly alkaline solutions. In order to obtain a better understanding of quartz activation by ferric iron the zeta potential of quartz in the presence of ferric iron has been measured over a range of pH and ferric iron concentration. EXPERIMENTAL METHODS Materials: Selected samples of "rock clystal" quartz from New England, N.S.W., were ground in a pebble mill, washed for three hours in boiling concentrated hydrochloric acid, washed in hot chromic acid and then washed repeatedly with distilled water until the washing water gave no trace of chloride ion.

Jan 1, 1967

By David W. Brunton

Mine-drainage and the ever-increasing demand for water on the plains have within the past few years necessitated the driving of a great number of adits and tunnels, including many of considerable size and great length. In most instances, existing conditions have called for extreme rapidity of execution; and this necessity, coupled with the high altitudes at which most of the work has been carried on, excessive freight-rates, and difficulty of access, has involved many complex and interesting problems. One of the most rapidly executed undertakings of this class is the Laramie tunnel, recently completed for the Laramie-Poudre Reservoirs & Irrigation Co. This tunnel is driven through Green ridge, a spur of the Continental Divide, which separates the Laramie river from the Cache-la-Poudre in Laramie county, Colo. Green ridge is extremely persistent, and further northward in Wyoming is known as Sherman hill, the highest point on the Union Pacific railway. At the point where the tunnel is driven, two opposing bends bring these streams within 2.5 miles of each other, with a difference in elevation of 500 ft. The rock exposed on the banks of the two rivers does not differ materially in hardness; and, without a geological study of the conditions involved, it would appear that the difference in the depth of erosion of the two streams is due principally to the greater volume of water at this point in the Cache-la-Poudre, which has a drainage-area above the tunnel-portal of 110 sq. miles, as against 30 sq. miles of natural drainage for the Laramie. To increase the water-supply at the tunnel, however, this latter amount has been augmented by two side collection-canals, which bring the available drainage-area up to 84 square miles. The nearest railroad shipping-point to the eastern portal is

Jan 1, 1913