Search Documents

By D. F. Toner, P. E. Gage, D. J. Mack

MUCH work has been done on the decomposition of the p phase at the eutectoid composition, 11.9 pct Al, in the Cu-A1 system by Smith and Lind-lief,' Mack,' Klier and Grymko,3 Haynes,4 and others. In all of the mechanisms proposed by these workers for the decomposition of the ß phase, it was stated that the a phase must precipitate rich in aluminum with respect to the equilibrium composition of 9.4 pct A1 at 565°C. To check this hypothesis, it was necessary to have a master curve relating equilibrium aluminum content of a to lattice parameters of a. A number '' binary Cu-Al alloys of increasing amounts of aluminum were prepared by Ampco Metal Inc. These alloys, received as-cast, were given a 30 pct reduction of area by hot-working and then annealed at 900°C for homogenization and slowly cooled in the

Jan 1, 1956

By Marsh S. Watson, Robert A. Howard

An electrolytic model study has been made of the relative productivity of perforated casing. The results show that the relative productivity is roughly one-half to two-thirds of that predicted from point-sink calculations. This discrepancy can he satisfactorily explained on the basis of casing interference. The relative productivity was found to he insensitive to spatial arrangement of the perforations. INTRODUCTION The relative productivity of wells with perforated casing has been treated mathematically by Muskat.' In his treatment the perforations are represented by small spheres, thus enabling him to approximate the flow by that to point sinks. By neglecting interference between the flow into the various spheres representing the perforations, one may deduce the approximate formula Qu 1/rp - 1/rw • (1) I + b/2n _________ 2n In re/rw Where Q is the flow rate into spherical sinks located in the median plane of the sand laver Qo is the open hole flow rate (uncased hole of radius rw) b is the thickness of sand layer under consideration (always one foot in this paper) n is the number of spherical sinks in the sand layer rp is the radius of a spherical sink rw is the well radius re is the drainage radius of the well. Fig. 1 is a comparison of values calculated from equation (1) with Mus-kat's values. It will be observed that the approximate values are in error by less than 21/2 per cent. The disturbing effect of the casing on the flow line; is not explicitly taken into account by Muskat, but he reasons that interference between the flow pat- terns from the various point sinks will result in a negligible flow in the region within the well radius, and that no appreciable error will result from not explicitly excluding flow from this region. This line of reasoning is open to question, however, as the flow impedance, in the immediate vicinity of the well, of a hemispherical cavity in contact with an opening in the casing is twice that of a spherical sink in a continuous sand layer. There will be a difference, moveover, between the flow into a hemispherical cavity and that into a circular hole in the casing. .This latter difference can best be appreciated by comparing the flow from a semi-infinite medium into a hemispherical cavity at the edge of the medium with the flow out of a circular opening of the same radius as the hemisphere and which is also on the edge of the medium. In this case2 ------= —2, showing that the difference in flow rates into differently shaped cavities is quite appreciable. It was the purpose of the investigation reported here to determine to what extent flow into circular perforations in casing departs from the values calculated by Muskat. For this purpose an electrolytic model was used.

Jan 1, 1950

By J. W. Spretnak, V. Kandarpa

Stress -induced ordering of carbon atoms is studied in a series of Fe-Mn-C alloys. A prominent peak is found in the vicinity of 280°C at frequencies of the order of 1.0 cps, with an associated activation energy of 37 kcal per mole. The height of the peak is linearly rekzted to the concentration of carbon in solution. The distortion of octahedral holes by manganese atoms appears to be predominant over carbon-carbon pair interactions. RELAXATION by stress-induced ordering of point defects is expected whenever the introduction of these point defects produces distortions which have a lower symmetry than that of the lattice. Under zero stress, the isolated point defects occupy the crystallographic-ally equivalent positions in the lattice, as these represent states of equal energy. However, if the defect sites are asymmetric, application of an uniaxial stress will split the energy states, and a redistribution of the defects among various states will take place. This is the case of the internal friction peak called the Snoek peak,1 resulting from isolated interstitials in bcc metals. The interstitial sites in this case have tetragonal symmetry. In the case of fcc and hcp lattices, such an effect is not expected from isolated point defects because of the symmetrical nature of the interstitial sites. However, internal friction peaks arising from interstitial diffusion have been reported both in hcp2,3 and fcc4-8 lattices. These peaks are often explained on the basis of stress-induced ordering of interstitial solutes, caused by the deviation of interstitial sites from their cubic symmetry through the presence of nearby defects. In the case of fcc lattices, evidence for interactions of both the substitutional-interstitial4,6,13 and interstitial-interstitial types5'798'14 have been presented by various investigators. The purpose of the present investigation was to study the internal friction peak attributed to the diffusion of interstitial carbon atoms in high purity austenitic manganese steels and to account for the peak in the light of the existing models. MATERIALS The Fe-Mn-C alloys used in the present investigation were made in two different ways, designated as Type I and Type 11. Type I alloys were made from high purity Fe-Mn alloys obtained in the form of 0.04- in.-diam wires from Materials Research Corporation, Orangeburg, N.Y. These alloys were carburized to different levels using gas mixtures of H2 and CH4 at 1000°C. Type I1 alloys were made in this laboratory starting with zone refined iron, spectrographically pure manganese, and spectrographically pure carbon. They were melted in an argon arc melting furnace and drawn into 0.04-in.-diam wires. All the wires were annealed at about 900°C for 3 hr prior to the internal friction experiments. After the measurements of internal friction, the phases in the samples were identified by X-ray diffraction and the carbon determined by the combustion method. EXPERIMENTAL PROCEDURE In the present work, a classical Ke-type pendulum was used. The details of the equipment were described previously by D. T. Peters.9 Dry helium at 40 torr was used in all the experiments. The internal friction, measured as the logarithmic decrement of the torsion amplitude of vibration was determined as a function of temperature, from ambient to about 500°C. The background internal friction was assumed to have the form of the exponential of the inverse temperature and was subtracted from the raw data. The height of the peak was measured at the position of the maximum in the plot of the internal friction versus temperature. The activation energies of the peaks were measured by the peak shift method. The internal friction values for an alloy were obtained as a function of temperature at different frequencies of vibration. The position of the peak changes with frequency, the higher the frequency the higher the peak temperature. The activation energy of the process associated with the peak is obtained using the formula

Jan 1, 1970

By K. O. Stamm, B. A. Rogers

Because it is the basis of the economically important operation of hardening steel by quenching, the A3 transformation in iron has been the subject of numerous investigations. Although the contributions to this subject are interesting, no general review will be given here. Readers who care to follow the matter further are referred to the comprehensive summary by Cleaves and Thompson,l which covers the literature to about 1935. Their references to 53 papers on the subject suggest that further investigation is hardly justifiable. However, considerable interest has devel oped recently concerning the reversibility of the transformation. From thermo-dynamic considerations, the transition ought to occur at the same point on heating or cooling, if the change of temperature is sufficiently slow. Yet all of the earlier investigators found a difference of several degrees. Burgess and Crowe,2 who used thermal methods, obtained average temperatures of 912" for Ac3 and 900°C. for Ar3 on electrolytic iron. Their data indicate a considerable range of temperature over which the change occurs, both on heating and on cooling. Terry3 measured the susceptibility in the critical range and estimated from the steepest parts of his curves that Ac3 came at 9I8° and Ar3 at 903°C. Ishiwara4 was one of the first investigators to report a shorter interval between the temperature of the change in the two directions. He measured the change of susceptibility of kaolin-coated samples of steel, in a hydrogen atmosphere, at rater of heating and cooling so low that about 3 or 4 hr. were required for the transformation to complete itself. His results show some variability between samples, but indicate that the difference between Ac3 and Ar3 is in the vicinity of 6°C. Roberts and Davey5 measured the space lattice in pure iron in the vicinity of 900°C. and concluded that a change occurs reversibly between 907' 3" and 910" 3°C., probably between 907" and 910°C. Wells, Ackley, and Meh16 made dilatometric determinations of the Ac3 and Ar3 points in samples of hydrogen-treated carbonyl iron maintained under a vacuum. They used three rates of heating and cooling: 2°, ½°, and .?°C. per min. and found the spread between the two points decreased with low rates. At the slowest rate, the Ac3 transition occurred at 909° to 909. 5°C. and the Ar3 change at 907°C. in three of the samples believed to contain the lowest percentages of alien elements. They concluded that if the rate of temperature change and the content of alien eiements were low enough, the A3 transformation would be completely reversible at 909.50 + 1°C. The question of reversibility is an interesting one and when some iron with especially small percentages of alien elements became available the opportunity to conduct an investigation was welcomed. This iron was prepared by the Division of

Jan 1, 1942

By B. A. Rogers, K. O. Stamm

Because it is the basis of the economically important operation of hardening steel by quenching, the A3 transformation in iron has been the subject of numerous investigations. Although the contributions to this subject are interesting, no general review will be given here. Readers who care to follow the matter further are referred to the comprehensive summary by Cleaves and Thompson,l which covers the literature to about 1935. Their references to 53 papers on the subject suggest that further investigation is hardly justifiable. However, considerable interest has devel oped recently concerning the reversibility of the transformation. From thermo-dynamic considerations, the transition ought to occur at the same point on heating or cooling, if the change of temperature is sufficiently slow. Yet all of the earlier investigators found a difference of several degrees. Burgess and Crowe,2 who used thermal methods, obtained average temperatures of 912" for Ac3 and 900°C. for Ar3 on electrolytic iron. Their data indicate a considerable range of temperature over which the change occurs, both on heating and on cooling. Terry3 measured the susceptibility in the critical range and estimated from the steepest parts of his curves that Ac3 came at 9I8° and Ar3 at 903°C. Ishiwara4 was one of the first investigators to report a shorter interval between the temperature of the change in the two directions. He measured the change of susceptibility of kaolin-coated samples of steel, in a hydrogen atmosphere, at rater of heating and cooling so low that about 3 or 4 hr. were required for the transformation to complete itself. His results show some variability between samples, but indicate that the difference between Ac3 and Ar3 is in the vicinity of 6°C. Roberts and Davey5 measured the space lattice in pure iron in the vicinity of 900°C. and concluded that a change occurs reversibly between 907' 3" and 910" 3°C., probably between 907" and 910°C. Wells, Ackley, and Meh16 made dilatometric determinations of the Ac3 and Ar3 points in samples of hydrogen-treated carbonyl iron maintained under a vacuum. They used three rates of heating and cooling: 2°, ½°, and .?°C. per min. and found the spread between the two points decreased with low rates. At the slowest rate, the Ac3 transition occurred at 909° to 909. 5°C. and the Ar3 change at 907°C. in three of the samples believed to contain the lowest percentages of alien elements. They concluded that if the rate of temperature change and the content of alien eiements were low enough, the A3 transformation would be completely reversible at 909.50 + 1°C. The question of reversibility is an interesting one and when some iron with especially small percentages of alien elements became available the opportunity to conduct an investigation was welcomed. This iron was prepared by the Division of

Jan 1, 1942

By H. L. Overton, J. B. Lipson

The concept of sodium single-ion equivalent activity as developed by Gondouin, Tixier and Simard,' was used to determine the filtrate resistivity-activity relationships for 150 laboratory and 49 field drilling muds. With the exception of the native and phosphate high-resistivity muds and the calcium-treated muds, the filtrate resistivity-activity relationships were found to be within 20 per cent of that for pure sodium-chloride solutions. Gondouin, et al,* previously suggested a method of treating the high-resistivity muds in quantitative electrical log analysis. A new treatment is presented which uses the P-alkalinity of the filtrate as a correlating parameter in handling the calcium-treated muds in quantitative electrical log analysis. INTRODUCTION Gondouin, Tixier, and Simard in 1957 introduced new interpretive procedures for analyzing the self-potential curve of electric logging. They re-emphasized the previous work of the Schlumberger brothers, Wyllie and others, and re-defined the activity concept in terms of a number which they termed the effective resistivity. Their procedures are particuarly effective when the connate-water resistivities are less than 0.08 ohm-m or greater than 0.3 ohm-m. For gyp muds where the calcium content is known, a procedure was presented which allows calculation of the connate-water resistivity with improved accuracy. These procedures assume that one of the fluids in the system is a pure sodium-chloride solution, but they are not limited by the assumptions. For the fresh and saline connate waters, for instance, it is assumed that the drilling mud filtrate is a pure sodium-chloride solution. For the gyp mud interpretive procedure, it is assumed that the connate water is a pure sodium-chloride solution. Brown,' on the other hand, has suggested that it would be extremely fortuitous if drilling mud filtrates could all be treated electrochemically as sodium-chloride solutions, and he cites some examples where discrepancies exist. A study has been made of the deviations of sodium single-ion equivalent activities, an of drilling mud filtrates from that of pure sodium-chloride solutions. Drilling fluids in common use on the Texas and Louisiana Gulf Coast and laboratory-controlled muds were investigated. Using a cell patterned after Gondouin, et al, (Fig. I), the equivalent activities were measured. It should be remembered here that the activity measured is merely an index which uses numbers that represent the sodium single-ion equivalent activity a,., of the mud filtrate. The membrane potential developed across the cell was determined with a null-type potentiometer. The resistivities of the solutions were measured by the four-electrode method. The resistivity system was calibrated by using saturated KC1 solution as a standard. Chemical properties of the drilling fluids studied were measured with standard API-approved equipment for the particular property in question. For the activity measurements, two shale discs were chosen to serve as cationic membranes. These two discs were both 1 1/4 in. in diameter and, respectively, 1/4 and 1/8 in. in thickness. The membrane potential, Em, was determined using the shale discs as cationic selective membranes separating two standard sodium-chloride solutions of known mean activity. Then by comparing the constant Km in the following equation, with the theoretical value of — 59 mv at 75OF, the perfection of the membrane was determined. The variation of Km for the two membranes used in this experimental work, as well as one of the many unsuitable membranes, is shown in Fig. 2. The measurement of the activity of mud filtrate involves the balancing of its combined individual activities against a standard solution of known mean activity. At the point where there exists zero potential across the membrane cell, the activity effects may be assumed equal for all practical purposes. The mechanics of making a null reading of this sort requires having a large number of different mean activity solutions. A more practical method involves

By C. L. Bulow

In this discussion of stress-corrosion cracking of widely used copper-base alloys, no attempt has been made to prepare an extensive review or bibliography since this has been quite ably covered by other investigators. An excellent bibliography was published by H. P. croft(1)2 in connection with his studies of stress-corrosion cracking in mercurous nitrate solutions and his analyses of the magnitude and distribution of stresses in brass parts. We are reporting on a few of the results which have been obtained to date in connection with an ammonia vapor test and an alternate immersion test. These are accelerated corrosion tests for determining the susceptibility of materials to failure from season or stress-corrosion cracking due to the presence of moist ammonia and oxygen so prevalent in nature. Our experiences with the ammonia test seem to indicate that it is a more searching test, than the mercurous nitrate test.

Jan 1, 1945

By Bernard E. Weichman

The oil shales of the Green River formation were deposited in an inland lake which contained abundant plant and animal life. A high percentage of sodium bicarbonate existed in the lower water layers. Digestion of the kerogen-rich mud accumulating on the lake floor lowered the pH of the interstitial waters and precipitated the sodium minerals dawsonite and nahcolite in the kerogen-rich mud. After about five million years of existence, uplift of land areas around the lake caused an influx of clastic sediments which filled up the lake. Continued tectionics gently folded the basin and caused fracturing of the kerogen-lean oil shale. Nahcolite existing in the fractured lean oil shale was dissolved by subsurface waters leaving a tremendous aquifer in a portion of the oil shale. The extent and porosity of the "Leached zone" aquifer is dependent upon the percent of kerogen and nahcolite originally deposited in the oil shale.

Jan 1, 1975

By R. L. Rickett, W. C. Leslie

The influence of deoxidation practice, prior thermal history, and aging time and temperature on the strain-aging behavior of low-carbon open-hearth steels was investigated. The criterion of aging employed was the increase in yield strength in the tensile test, after straining and aging. Composition, prior heat treatment, and aging conditions were all found to be important in governing the strain-aging characteristics of these steels. THAT deoxidation changes the strain-aging propensities of low-carbon steels has been known for a long time, but there has been little agreement, and even contradiction, between results obtained by different investigators and between results obtained in the laboratory and in the mill. This investigation was begun in the hope that some of the uncertainties connected with the strain aging of commercial steels could be eliminated. In considering this problem, it was necessary to define strain aging and to examine the methods used to measure this property. Strain aging can be defined as the changes in properties of a metal or alloy with time, after cold working. The rate at which these changes occur increases as the temperature is raised above atmospheric. The requisite plastic strain is the principal distinction between strain aging and quench aging, the latter being due to precipitation from supersaturated solid solution. Strain aging is also characterized by rapid attainment of maximum hardness at high aging temperatures and lack of softening (overaging) at low aging temperatures. Several possible criteria of strain aging have been listed by Sachsl and by Davenport and Bain.' Because changes in mechanical properties are the most easily measured and the most commonly used, consideration of methods to be used in this investigation was confined to three tests: tensile, notch-impact, and hardness. Hardness tests are the most economical and easiest to perform, but produce only one measure of strain aging. Also, as pointed out by Felmly, Hartbower, and Pellini,³ hardness changes due to aging are not pronounced for steels containing more than 0.15 pct C. Notch-impact tests require careful preparation of large numbers of specimens. Above and below the transition temperature the test lacks sensitivity; furthermore, it is extremely difficult to impart a uniform strain to the specimens, followed quickly by aging and final testing; machining must generally take place after straining. For these reasons, the tensile test was selected for use. Although this test requires a considerable expenditure of time, labor, and money in preparation of the specimens and performance of the test, more information can be gained than from any other single mechanical test, information which includes upper and lower yield points, yield-point elongation, tensile strength, strain-hardening exponent, reduction of area, and elongation. Low and Gensamer' and Schwartzbart and Low5 lso used the tensile test, taking the increase in flow stress after straining in tension and aging as a measure of strain aging. In our work, as in theirs, each specimen was strained an arbitrary amount, sufficient to pass through the

Jan 1, 1954

By O. Bilharz

The rules laid down by Peter von Rittinger in his classic Lehrbuch der Aufbereitungskunde (Berlin, 1867, p. 513) concerning the designing of dressing-works still possess authority for such works and their operation. Nevertheless, some modifications and additions suggested by practice may be of value at the present time. Rittinger says: "I. Choose the apparatus and machines which can be, under the existing con-' ditions, easily constructed and kept in running order!' This rule contemplates the construction of apparatus (mostly of wood) on the spot, with the command of good sbops and especially of good workmen in wood. But in many cases, particularly for the sake of a prompt supply, the construction of apparatus is now left to special manufactories, which pay more attention in the choice of materials to durability and strength than to easy manipulation and erection. Nevertheless, here,as in many other instances, simplicity of construction and solidity of execution are to be recommended. Especially important is the convenient and cheap replaceability of

Jan 1, 1894

By Akira Ishizu, Nobuo Matsui, Hideo Yamamoto, Tatsuya Nagahama

At Kamioka Mine of Mitsui Mining & Smelting Co., Ltd., Japan there are three mills, treating a total of 6400 t/d of lead-zinc Ore. In the lead-zinc bulk differential flotation at Shikama Mill the addition of reagents is automatically controlled by the feed rate, the lead and zinc content in feed, froth and tailing, the pH and the concentration of cyanide ion in the pulp. As the zinc thickener overflow at Shikama Mill contains CU(CN)3--, ZnS, CdS, CN-, xanthate and frother, all the ingredients in the over- flow other than CN are floated by using the Nagahm flotation machine, and the water containing only CN- is effectively recycled to the lead- zinc differential flotation circuit. In the lead-zinc straight differential flotation at Mozumi Mill, the overflow of tailing pond is recycled especially to the cleaning flotation circuit by decreasing the pulp density. Thus the integrated recycling of wastewater greatly reduces environmental problem and in addition, it generates sizeable profit.

Jan 1, 1977

By A. D. Mutch

This contribution is prompted by the fact that the writer has recently published an article" which has in part the same general conclusions as B. S. Butler's, namely, the form of the standard mineral paragenesis in hypogene deposits and the parallel transition from early high temperature acid to late low temperature alkaline or neutral solutions. Since the writer also recognizes that he is not fully qualified to discuss the formation of ore deposits as a chemical problem, this discussion will be limited to summarizing other observations and will suggest how Butler's Table II might be made more effective. The form of Butler's table is not unlike that widely used by European geologists30 in which the various minerals are related to the types of ore fluids-pegmatitic, pneumatolic and hydrothermal. Thus the decrease in temperature and change in pH of the ore- bearing fluids as recognized by Butler may also be paralleled by perhaps even greater changes in composition, density, and character.

Jan 5, 1958

W. N. Triplett (Geology of the Silver-Lead-Zinc Deposits of the Avalos-Providencia District of Mexico, P. 583) was born in Tecumseh, Mich., and attended the University of Michigan and Massachusetts Institute of Technology. From 1912 to 1917 he worked for Moctezuma Copper Co., a Phelps Dodge subsidiary at Nacozari, Sonora, Mex. He served in Army as Second Lieutenant Field Artillery from 1917 to 1918 and from 1919 to 1922 returned to Moctezuma Copper Co. From 1922 to 1952 he has been with Compania Minera de Penoles, S. A., a subsidiary of American Metal Co., Monterrey, N. L., Mexico in Unit Dept. as chief geologist and at present is consulting geologist. Mining geology and operation is of particular interest to Mr. Triplett. He presented a previous paper before with M. W. Hayward entitled, "Occurrence of Lead-Zinc Ores in Dolomitic Limestones in Northern Mexico." Besides being an AIME member, he holds membership in Society of Economic Geologists. Fishing, hunting and photography are his favorite hobbies.

Jan 1, 1952

By T. E. Seidel, A. U. MacRae

The dependence of the electrical and crystalline properties of silicon containing ion implanted boron atoms have been studied as a function of the incident dose, substrate temperature, and annealing tempera-ture. Hall effect studies show that the compensation due to defects is negligible after annealing at and above 500°C for a dose of 1013 ions per sq cm. Steps occur in the isochronal annealing curve for the sheet resistance at 300°C and 800°C and the mechanisms responsible for these steps are discussed. The range of the ions at 150 kev is 3500 * 5001. Electron diffraction studies on samples implanted with 150 ker ions show the existence of damaged (polycrystalline) silicon closer to the surface than the range of the ions. Etching and subsequent annealing of etched and unetched specimens suggest that the poly crystalline silicon is closer to the surface than the bulk of the distribution of ions. THE purpose of this study is to investigate some electrical and crystalline properties of ion implanted boron in silicon. Sheet resistance, Hall measurement, depth distribution by chemical staining, thermal probe and electron diffraction have been used to study the properties of samples implanted in a random direction with ions having energy up to 150 kev. The boron-silicon system has been the subject of considerable study'-7 due to its possible application in the fabrication of electronic devices. The implanted ions produce considerable crystalline damage to the substrate crystal before they lose most of their primary energy and come to rest. Fortunately, most, if not all, of this damage can be removed by subsequent annealing or by holding the substrate at an elevated temperature during the implantation process. Sheet resistivity measurements of the p-type layers produced by boron implantation into room-temperature silicon, reveal that the annealing occurs in a two-step process: the first occurring at -300°C and the second at -800°C.' Electron-microscope and low-angle electron diffraction studies of this damaged material indicate that the bombarding ions produce an amorphous silicon region about the trajectory of each ion.' At high doses, these damaged regions overlap and an amorphous surface layer results. Furthermore, the 800°C annealing step, appears to be associated with the elimination of this gross damage. The depth distribution of the as-implanted and also the annealed samples have been studied by an angle lap and staining technique as well as by Hall measurements.3-7 We find the experimentally determined ranges of the boron are less than those calculated by the Lindhard-Scharff-Schiott theorys (hereafter referred to as the LSS theory). Our results are in essential agreement with pre- vious results. In addition, we have made Hall measurements on samples bombarded with a low dose (2 x 1013 ions per sq cm) to minimize impurity banding effects, and find that deep ionized levels influence the carrier concentration and room-temperature hole mobility until the sample is annealed at temperatures above 500°C. Above this temperature, the data corresponds to that obtained when silicon is doped with boron by conventional techniques. We have also made a depth distribution determination of the crystalline damage due to the implanted boron by using glancing angle electron diffraction techniques. It was found that the gross damage depth distribution of heavily implanted samples is closer to the surface than the depth distribution of the electrically active boron. By removing this gross damage, without affecting the distribution of the implanted boron, we have determined that the 800°C annealing stage is not exclusively due to the improvement in the crystalline perfection of the amorphous material but also appears to be associated with the annealing of some point defects. These results and their relation to previous results are discussed in the following sections. IMPLANTATIONS Boron ions were implanted into silicon samples using an accelerator capable of operating from 10 to 150

Jan 1, 1970

COLUMBIA LOCAL SECTION STANLY A. EASTON, Chairman, FREDERIC KEFFER, Vice-Chairman, L. K. ARMSTRONG, Sec.-Treas., P. O. Drawer 2154, Spokane, Wash. The fifth annual meeting of the Columbia Local Section was held in Wallace, Idaho, November 19-20, 1915, with headquarters at the Samuel Hotel. The afternoon session scheduled for November 19, was adjourned to give the members an opportunity to hear the testimony in the case between the Alameda and Success mining. companies on trial in the Superior Court of Shoshone County. The Success Company offered some excellent mine models and maps and furnished some interesting testimony. In the evening a technical session was held at which Stanly A. Easton presided in the absence of the Chairman and Vice-Chairman of the Section. The following papers were read: Progress in Ore Dressing By D. W. Buckby,.. Mine Accounting for Small Mines, By J. E. Chapman. Zinc Smelting and Smelter Rates, By W. E. Henry.

Jan 2, 1916

By J. Bruce Clemmer, P. E. Churchward, Carl Rompacek

The paper describes a cyclic method for processing manganese ores using sodium sulphate as the basic reagent. Sodium sulphate is electrolyzed in a diaphragm cell to give an anolyte sodium sulphate acid and a catholyte containing caustic soda, a part of which is carbonated in a cyclic manner to form soda and reduced ore is leached with the anolyte to dissolve the manganese and the impurities are precipitated by addition of catholyte. Manganese in the pregnant solution is precipitated as synthetic rhodochrosite with a carbonated catholyte, and sodium sulphate is regenerated. Calcining the manganese carbonate site a high-grade product and the carbon dioxide is returned to the carbonation step. the results of laboratory tests using cells equipped with synthetic fiber diaphragms and permselective membranes which permit transfer of using or cations during electrolysis are described. The article from which the above abstract is reprinted appears in Trans. AIME (1955) 203, p. 51; Journal op Metals (January 1955).

Jan 1, 1956

By A. W. Schlechten, C. M. Hsiao

The apparent vapor pressures of a number of metal sulphides were determined by measuring their rate of weight loss when they were heated under vacuum. The calculated pressures are due in some instances to the volatility of the sulphide and in others to the decomposition pressure. FIE direct reduction of metallic sulphides, as in the precipitation method for lead or antimony, is not a widely used process today. However, it might be employed for the production of a number of metals if the operation were carried out under reduced pressures. Two general procedures are possible; the reducing agent could form a stable nonvolatile sulphide from which the valuable metal could be removed by volatilization or liquation. The other approach would be to choose a reducing agent which would form a sulphide that could be volatilized away from the valuable metal. A vacuum operation would serve to protect the sulphides and metals from oxidation and would increase the evaporation rates. A related process is the separation of metallic sulphides by selective volatilization either at atmospheric pressure or under vacuum. This procedure is already used commercially for the elimination of lead and cadmium as PbS and CdS from zinc calcines; it might well have other applications. To predict such processes it is necessary to know the relative volatilities of the metallic sulphides and to know whether they volatilize as sulphides or whether the predominant weight loss is due to decomposition. Such data would also be of value in studying problems such as the use of sulphides for refractories, as described by Brewer,] or in the evaluation of the theory of ore deposition from the vapor state, as proposed by Brown.' Qualitative statements concerning the volatility of metallic sulphides can be found frequently in the literature and are well summarized by Mellor, but accurate determinations of rates of evaporation or vapor pressures are very scarce. Kelly" lists vapor pressure data only for PbS; his reference being to the work of Schenck and Albers,4 who measured the vapor pressure of PbS by a dynamic method between 850" and 995°C. More recently Veselovskii5 has determined the vapor pressures of the sulphides of antimony, lead, cadmium, and zinc at temperatures ranging from 360" to 1000°C using Knudsen's method. A second Russian worker, Pogorelyi,6 determined the vapor pressures of CdS and ZnS at temperatures from 900" to 1250°C. The results obtained by these workers are shown in subsequent graphs in comparison with the data of this paper. Brewer and coworkers1 have studied some of the metallic sulphides to determine their suitability as refractories in vacuum. Veselovskii's determinations on PbS checked well with those of Schenck and Albers, and his determinations of CdS check almost exactly with Pogo-relyi. For the vapor pressure of ZnS the data of Veselovskii and that of Pogorelyi are in fair agreement, as shown in Fig. 1, but it should be pointed out that Lumsden7 has discovered that the equation given by Veselovskii for the vapor pressure of ZnS: - 14,200 log P9.495 is in error by a factor of ten when compared to the experimental data. In contrast with the scarcity of data on vapor pressures, the decomposition pressures of many metal sulphides have been determined and are summarized by Smithells.8 Theoretical Considerations The experiments described in this paper consisted of determinations of the rate of weight loss of certain metallic sulphides under very low pressures at different temperatures. These data plus observation and analyses of the products reveal the mechanism of the weight loss and also provide a basis for the calculation of the vapor pressure or apparent vapor pressures of the sulphides.

Jan 1, 1953

Discussion of the paper of GEORGE K. BURGESS and SIR ROBERT A. HADFIELD, presented at the New York meeting, February, 1915, and printed in Bulletin No. 98, February, 1915, pp. 455 to 468. ALBERT SAUVEUR, Cambridge, Mass.-There is a definiteness and finality in the investigations that have been conducted by the Bureau of Standards and in the method of presenting the results that is most satisfactory and refreshing.. A year ago Dr. Burgess and his co-workers investigated the question of critical points in carbonless iron, and they settled the question once for all. No one can now claim that the thermal point A2 in carbonless iron does not exist. At the past meeting of this Institute in Pittsburgh, Dr. Burgess showed the worthlessness of the shrinkage clause. To my mind after his demonstration no one can again claim that the shrinkage clause renders any service. He also showed us that it was a practicable proposition to use pyrometers in steel work in order to ascertain the finishing temperatures of rails. No one can again come before this body and make the claim that it is not a practical proposition. And now Dr. Burgess shows us that steel ingots can be made in a commercial way, practically free from pipe, from segregation, aid from blow holes. It places again before us in a very clear manner the question of piped ingots and of segregation, a question which has been debated for 20 years or more. I know very well the attitude of the standpatters in the matter. They claim that most of the pipe is removed in the discard, and that if a little is left it is so thoroughly welded that it does no harm. I for one am not convinced of the soundness of the argument. I do not believe there is any one present who would claim that, given an ingot free from pipe, free from segregation, and free from blow holes, better rails will not be made out of that ingot than out of the ordinary piped or segregated metal which is used by almost all of our steel mills. In my opinion, if we give our sanction to the casting of steel in the shape of piped or segregated steel ingots, we are guilty. If we give our sanction to the rolling of rails from such metal, we are guilty. It is our duty as experts, as steel makers, and as steel consumers to make and to use the best steel obtainable on a commercial basis, for the manufacture of rails. Now, we have been shown that sound ingots can be produced from which superior rails can be made. If we do not insist upon these sound ingots, then we fail in our duty. I think that the art of casting steel ingots has advanced to such a point that the casting of steel ingots piped and segregated ought no longer to be tolerated.

Jan 5, 1915

By Henry M. Howe

This paper may be regarded as a report of progress of an investigation into the influence of prior exposure to different high temperatures, under different conditions, on the properties of steel after it has been cooled completely. The following are the chief divisions: II.—Experiments on toughening manganese-steel by sudden cooling. III.—A study of the critical points of common or carbon-steel, chiefly by examining the spontaneous retardations which occur in heating and cooling it, and by examining the ductility of pieces of steel which have been cooled suddenly from different temperatures by quenching them in water or brine. IV.—A brief note on Osmond's theory. V.—A study of the critical points by examining the ductility of pieces of steel which have been cooled slowly from different temperatures at, above, and below them. VI.—A description of the furnace used, with notes on thermoelectric pyrometry. It remains to throw further light on the questions studied by ascertaining the condition of the carbon and the hardness proper, and by studying the microstructure and the fracture of the many pieces treated. I hope to present later the results of experiments in some of these directions. With few exceptions, the experiments have been performed in my private laboratory. I tender sincere thanks to my assistant, Mr. William Haskins, S.B., on whom most of the labor has fallen, for his zealous and intelligent co-operation; to the Sterling Steel Co. for their extra hard steel, Series 17; and to Mr. Joseph Hartshorne and the Pottstown Iron Co. for their soft basic steel. Series 8, 9,10, and 18 were supplied by Messrs. Spaulding, Jennings & Co., of the West Bergen Steel Works; to them also my thanks are due. The temperature of the pieces treated has been very carefully

Jan 1, 1894

By L. D. Jaffe, D. C. Buffum, F. L. Carr

SINCE the temper brittleness of steels is generally considered to be a grain-boundary phenomenon¹,² it would be expected that austenitic grain size would affect temper brittleness. Several investigators"" reported that temper brittleness, as measured by room-temperature impact tests, increased as the austenitiz-ing temperature was raised. It was subsequently pointed out that conclusions as to temper brittleness based upon room-temperature impact tests are likely to be misleading.1,6 Hurlich7 used a range of testing

Jan 1, 1954