Search Documents

By E. V. Crane

A tremendous volume of the metal rolled annually into sheets strips and coil stock finds its way to a host of stamping and manufacturing plants which are the quantity production units of the country. Considerable in volume, too, are the rolled and extruded rods which go into forging and manufacturing plants for conversion into the same general line: those widely sold metallic necessities and luxuries of the household, the office, transportation, farming and building construction. Yet, in spite of its age and its importance, the stamping trade has been doing its "engineering" largely by trial and error. Its distinctive method is shearing out and plastically working metal to finished shape in a few quick strokes with high loads and expensive tools which are warranted only by large quantities to be produced. The principal operations have many features In common with rolling and wire-drawing methods. Combinations of stresses are diffcrent, however, and details of operations are infinite in variety. An engineering study of the subject begins with stress analysis, but must go back to metallurgy for its foundation. A grouping of pressed-metal working operations according to whether the metal is (1) sheared, (2) bent, (3) drawn or (4) squeezed has proved useful. All of these groups include instances of both hot and cold operations. For discussions of metal working properties, the division between hot and cold working is taken as the recrystallization range of temperature. This, of course, brings tin, lead and often zinc into the hot-work range at or near room temperature. The outstanding hot-working press field is in forging: particularly of brass; all of which is included in the squeezing group. Shearing Operations The shearing group of operations, including blanking, piercing, trimming, shaving, slitting, shearing, notching, parting and numerous variations and combinations of these enters once or more into the production schedule of practically every stamped or forged article. The transverse stress, set up in shearing, as shown in Fig. 1A, is a combination of an angular compressive thrust and a tensile stress which is also at an

Jan 1, 1931

By C. W. Pritchett

Several years ago, during a trip from Jojutla to Huauatla, in the abate of Morelos, Mexico, I was told by my guide of the ruins of an old smelter near by, and my curiosity was excited to such an extent that I went out of my way several miles to see them. I found them very interesting; and, as I fortunately

Jan 1, 1902

By Frank W. Harris

The strength of hard drawn copper wire is a question of considerable importance to both manufacturer and consumer. Unlike steel and alloy wires, in which strength is governed by both chcniical and physical considerations, t,he high conductivity required for copper wire in the clcc-trical industry generally precludes the possibility of obt,aining tensile strength through the use of alloys. Consequently, this strenglh is largely a rnatter of the ~hysical structure, and all factors known to affect this structure, such as rolling temperature, die contours, lubricants, drawing speeds, etc., arc matters of prime importance. The experiments described here have becn carried out dl~ring the past year at the Baltimore plant of the American Smelting & Refining Co., in connection with a general investigat,ion of sorne of the questions mentioned above, with the object of studying thc physical ~t~ructure of hard drawn copper wire and the influence of ccrtain factors on t,hat st'ruct.ure. The work has been of an exploratory nature, rather than con~prehensivc., but it was thought that the result,s might prove of sr~fficient general interest tjo warrant their publicatlion. The bulk of the hard drawn coppcr wire used in places where strength is an important factor is rnanufacturcd to strict specification, based USU-ally in the United States on thab of t,he Arrlerican Society for Tcst'ing Materials (B-1-23). This specification calls for almost as high a, valuc of t,ensilc strength, consistent with elongation, as it is possible pract'icnlly to obtain, and only physically perfect mlaterial can be relied on to lliect such a specification. Obvious defects, such as laminat'ions protluc:etl through fins in bhe original rods or brittleness duo lo ovt~rdrawing, arc. usually recognized and need only passing refercncc. Laminatlions can be detected by twisting and untwisting the wircx several times; they will show up on the surface in the form of fins. Pig. 1 shows a very bad example of this defect. Thc wire may bc perfectly smooth before twisting hut, when such larrlinations arc3 prcstmt they will readily show up under this treatrncnt. This trouble is caliscd by sirriilar defects in the original rod produced by overfills in rolling. Fig. 2 shows the cross-section of the rod from which thc wire in Fig. 1 was drawn.

By F. N. Rhines, A. H. Grobe

At elevated temperatures the oxide of silver is unstable in the air at atmospheric pressure, consequently no external oxide scale forms upon pure silver under conditions of high-temperature annealing. When small quantities of certain alloying elements are present in the silver, the formation of a thin external scale is possible1 and in addition there may form a subscale composed of the oxide of the solute element precipitated within the body of the silver. Norbury2 and Leroux and Raub3 have reported internal oxidation (subscaleiormation) in alloys of silver with 2, 7.5, and 30 per cent of copper. The presence of the subscale is believed to be responsible, at least in part, for the objectionable "fire mark" in Sterling silver.4 Several other alloys of silver, after oxidizing heat-treatments, are known to exhibit undesirable polishing characteristics that may be the result of internal oxidation. Except for the absence of an external scale of silver oxide, it is to be anticipated that silver alloys will prove to be very similar in their oxidation behavior to the alloys of copper, the oxidation characteristics of which have been studied in some detai1.5,6 The present research confirms this anticipation. The oxidation of a series of 20 dilute alloys of silver has been studied metallographically; some types of subscale not encountered among the copper alloys have been found. Instances of internal oxidation in alloys of most of the metals of the 1-6 and VIII groups of the periodic system are on record, but evidence of this type of oxidation in alloys of the metals of the intermediate groups is lacking. A number of the metals of the intermediate group, among them cadmium, lead, tin, and zinc, appear to provide the conditions essential to subscale formation; i.e., they form oxides with a relatively low negative free energy of formation, they dissolve other metals that form more stable oxides, and, presumably, oxygen will diffuse through them. In a study of 40 alloys of these white metals only a few cases of internal oxidation have been found. The probable reasons for this difference in behavior will be discussed presently. Experimental Procedure Silver.—The silver alloys employed in the oxidation studies were prepared in heats of 30 grams each from high-purity silver (99.993 per cent Ag)* and the purest avail-

Jan 1, 1942

By A. H. Grobe, F. N. Rhines

At elevated temperatures the oxide of silver is unstable in the air at atmospheric pressure, consequently no external oxide scale forms upon pure silver under conditions of high-temperature annealing. When small quantities of certain alloying elements are present in the silver, the formation of a thin external scale is possible1 and in addition there may form a subscale composed of the oxide of the solute element precipitated within the body of the silver. Norbury2 and Leroux and Raub3 have reported internal oxidation (subscaleiormation) in alloys of silver with 2, 7.5, and 30 per cent of copper. The presence of the subscale is believed to be responsible, at least in part, for the objectionable "fire mark" in Sterling silver.4 Several other alloys of silver, after oxidizing heat-treatments, are known to exhibit undesirable polishing characteristics that may be the result of internal oxidation. Except for the absence of an external scale of silver oxide, it is to be anticipated that silver alloys will prove to be very similar in their oxidation behavior to the alloys of copper, the oxidation characteristics of which have been studied in some detai1.5,6 The present research confirms this anticipation. The oxidation of a series of 20 dilute alloys of silver has been studied metallographically; some types of subscale not encountered among the copper alloys have been found. Instances of internal oxidation in alloys of most of the metals of the 1-6 and VIII groups of the periodic system are on record, but evidence of this type of oxidation in alloys of the metals of the intermediate groups is lacking. A number of the metals of the intermediate group, among them cadmium, lead, tin, and zinc, appear to provide the conditions essential to subscale formation; i.e., they form oxides with a relatively low negative free energy of formation, they dissolve other metals that form more stable oxides, and, presumably, oxygen will diffuse through them. In a study of 40 alloys of these white metals only a few cases of internal oxidation have been found. The probable reasons for this difference in behavior will be discussed presently. Experimental Procedure Silver.—The silver alloys employed in the oxidation studies were prepared in heats of 30 grams each from high-purity silver (99.993 per cent Ag)* and the purest avail-

Jan 1, 1942

By J. D. Price, G. V. Woody

MANY producers of by-product coke have spent considerable time and given considerable thought to the use of a substitute for low-volatile coal as an admixture with high-volatile coking coal for charging high-temperature by-product coke ovens. Generally speaking, there are two principal reasons for this, one being occasioned by the lack, in certain localities, of low-volatile coal delivered at a cost sufficiently low to permit its use, and another being the desirability of finding a substitute product with a delivered cost lower than the cost of the low-volatile coal. It was for the first of these reasons that the Colorado Fuel and Iron Corporation was particularly interested in this subject. This paper deals with the experimental work and the results obtained by that company in producing and using low-temperature char. OVERCOMING DEFECTS IN COKE FROM COLORADO COALS Colorado coking coals are all of the high-volatile type and were all laid down during he Cretaceous period, which makes them something like 80 million or so years younger, geologically, than eastern coals. They behave, when coked alone, something like the Pittsburgh-seam coals. They make a very brittle, highly cross-fractured, fingery coke of fair shatter value but quite low in resistance to abrasion. Mixed with a low-volatile coking coal such as Pocahontas or certain Oklahoma coals, they make a coke that is equal to virtually any of the eastern cokes. The inferior quality of Colorado coke has long been recognized, and a considerable amount of time, effort and money has been spent upon investigations of means for improving its physical properties. While it has been found that some improvement in quality of coke can be secured by the adjustment and control of such variables as pulverization, moisture content, oven temperature and bulk density of charge, and through the addition of certain inert materials such as pulverized coke breeze, pitch, high-volatile noncoking or semicoking coal, the benefits so gained have been comparatively small. There are no low or medium-volatile coking coals available within a reasonable freight-cost distance. Therefore a substitute for low-volatile coal was developed through low-temperature carbonization-or, more correctly speaking, through the partial devolatilization-of high-volatile coals. The blending of this lower volatile char with the high-volatile coking coal distinctly improves the quality of coke made from Colorado coal. There is nothing especially new about this idea. In 1908 a Japanese patent was taken out by Kotaro Shimomura, whose claim was: The method of making a nonfingery coke out of bituminous coals, without using natural coals of low-volatile matter; according to which a certain coal is heated at a temperature between about 300°C. and about 600°C. so as to leave about 15 to 25 per cent volatile matter in the coal; this coal is mixed with the

Jan 1, 1944

By L. W. Strock

Metallurgists handling lead and zinc ores have long been familiar with the spectrograph as a routine analytical tool, as its earliest regular use by American industry was in controlling impurities of zinc metal and its alloys. This application has been extended to other metal industries on an extensive scale, accompanied by refinements of procedure to such an extent that a large part of some metals produced, especially magnesium, aluminum and steel, are checked only by spectrographic methods for conformity to specifications. The spectrographic analysis of ores and other poorly conducting powdered solids presents difficulties not encountered with metallic samples, which can be arced or sparked as self-electrodes or can be readily dissolved, so that their solutions can be analyzed, as in the American Society for Testing Materials standard methods for zinc and zinc-base alloys. Spectra of powdered solid samples can be prepared by using carbon electrodes provided with a crater of suitable size, into which the sample is packed. Ore samples and many other powdered solid materials usually analyzed in the chemical and metallurgical laboratory are more complex and varied in composition than samples of metals produced in large tonnages. 'lore preliminary work therefore is usually necessary in devising a spectrographic method for analyzing a given type of powdered sample than for analyzing metal samples, in order to use that method with confidence. The howledge that the standard samples and unknowns produce equivalent line intensities at equal concentration is the fundamental basis of any quantitative spectrographic method. On the other hand, powdered samples have an advantage over metals in that any desired number of chemical compounds can be mixed dry in any desired ratio to produce a synthetic standard. Expcrience has shown, however, that spectra of elements in finely divided compounds introduced into a standard in preparing a synthetic ore sample do not always behave in the electric arc in a manner that produces spectral line intensities similar to those observed at the same concentration in a natural mineral. In ore samples minor elements frequently are contained in the crystal lattice of larger particles of an abundant ore mineral. Their dissociation and volatilization from the sample into the arc then proceeds differently in the standard and sample, with resultant differences in intensity. During the past 10 years I have devised and applied several quantitative spectrographic methods for determining various elements in rocks and minerals in connection with studies on their geochemistry,' but the incentive has gradually changed since the summer 0. 1940 to the specific practical problem of searching for domestic sources of rare and stratcgic metals. The

Jan 1, 1949

By A. W. Gauger

Coal as mined contains varying quantities of inorganic components (mineral matter) which, on combustion, produce the residue known as ash. It has long been realized that the weight of this residue does not equal the weight of the mineral matter originally in the coal, because of the chemical changes that take place during the ashing process. Moreover, the ordinary ash analysis presents the ash as a mixture of oxides with little or no clue to the identity of the mineral species originally present in the coal. It is only for pyritic sulfur that an attempt is made to determine a mineral component. So far as the authors are aware, there are practically no experimental data in the literature as to the percentages of the different mineral species present in coal. The oft-quoted table of Marson and Cobb1 cannot rightly be considered as data, since the authors merely state that the table "shows the probable forms in which these ash constituents exist in coal." In view of the attempts to calculate analyses and determinations of the calorific equivalent of coal to the mineral-matter-free basis, as well as the importance of the mineral species in clinkering, combustion and coking, it seems strange that so few data are available on this phase of coal technology. For example, numerous empirical corrections for use in the scientific classification of coal have been suggested to compensate for the losses from the mineral matter during ignition of the coal to ash. These include multiplication of the ash percentage by various factors such as l 1/10 and 156, the use of the Parr unit coal formula (1.08 A + 22/40 S, where S = total sulfur) as well as certain modifications of the Parr formula that attempt to correct for the organic sulfur present in the coal. Although many experiments have been made to determine the loss on ignition of the clays associated with the coal measures and correction

Jan 1, 1934

By S. A. Mersol, C. T. Lynch, F. W. Vahldiek

The room-temperature Knoop hardness of single -crystal titanium diboride has been determined. Variations in microhardness have been correlated with orientation and structural imperfections in the crystals. Maximum differences in hardness values of 750 kg per sq mm with respect to orientation and 450 kg per sq mm with respect to substructure were found. The effects of etchants, load on indenter, and degvee of cracking of indentation were studied. The average hardness was determined as 2800 kg per sq mm on the as-grown crystals. Annealing increased the average hardness to 3375 kg per sq mm. ThE microhardness of polycrystalline titanium diboride approximating the stoichiometric composition TiB, has been studied by several investigators. The values for the Knoop hardness number range from 2710 kg per sq mm (Khn = 2710 kg per sq mm) to 3400 kg per sq mm.'-4 Samsonov et al.' reported a Vickers hardness number of 3400 kg per sq mm (Vhn = 3400 kg per sq mm) at 120-g loads for a 98 pct Ti + B material of 96 pct theoretical density. Recently Dunegan measured the Vickers hardness and obtained 2060 kg per sq mm with a 10-g load (Vhnlo = 2060 kg per sq mm), 1425 kg per sq mm for Vhnloo, and 1320 kg per sq mm for Vhnlooo. We have obtained a Khnloo = 3000 * 350 kg per sq mm for hot-pressed polycrystalline TiB2 that was 99.1 pct Ti + B and 96.6 pct of theoretical density. The present investigation has been made on single-crystal titanium diboride boules, and is believed to be the first such study on TiB, crystals of known orientation. EXPERIMENTAL The single crystals were prepared by a Verneuil-type process using an electric arc by the Linde Division of Union Carbide Corp. The largest specimens were 6 mm in diameter by 12 mm long. The crystals were of theoretical density (4.50 g per cm3) with a Ti + B content of 99.8 pct. The major impurities present were: 0.03 pct (by weight) 0, 0.06 pct C, 0.01 pct Si, 0.05 pct Fe, 0.01 pct Cr, and 0.01 pct Ni. The crystals were boron-rich, the average boron content being 31.S7 wt pct (stoichiometric value is 31.12 wt pct), and titanium-poor, the average titanium content being 68.2 wt pct (stoichiometric value is 68.88 wt pct). Titanium was determined gravimetrically by cupferron precipitation and boron by titration of H3B03 from a NaOH-fused specimen after removal of titanium with BaC03. The outer edge of the boule accounted for some of the excess boron. An electron-microprobe analysis showed that the titanium content increased from 60.0 wt pct at the edge to 68.5 wt pct at D, ~ 1000 p, where D, = distance from outer edge (see Fig. 5). X-ray measurements indicate that the boules are single crystals with considerable substructure. Upon etching this structure is seen in the form of a Widmanstatten-type rhombohedral line pattern in the basal (c) plane and a parallel "lines" pattern in the prism (a) planes. A typical WidmanstHtten-type pattern is seen in in Fig. 1. Electron microscopy reveals that the lines are less than 1 p across, which does not allow direct electron probe or microfocus X-ray determination of their composition. The identity of the second phase has not been established. It might be a higher boride or a nonstoichiometric TiB2. On annealing above 2200°C the precipitate is dispersed and dissolves in the matrix. The best etchants found were HF/HNO/HO, KF(CN)$NOH/HO (Murakami's Etch), and A large number of other etchants were previously Studied. The acidic etchant produced an acicular or "needles" pattern in the (a) planes which is an etchant effect on the "lines" pattern.

Jan 1, 1965

By T. P. Harrington, P. G. Doctor, K. A. Prisbrey

Crushing and grinding ore consumes so much energy that it represents a major component of total processing costs. While it has been estimated that only about 0.6% of the total energy expended in grinding is actually used to create new surfaces, accurate measurement of this quantity is difficult. If energy expended in crushing and grinding could be more directly measured, alternatives for increasing efficiency of the processes could be evaluated more effectively. Since the energy intensity associated with rock fracture is related to fracture sonority, it should be possible to use this sound (acoustic emission) to measure the actual energy expended. However, it is difficult to apply this approach because the mill environment is so noisy. To make the approach practical, a method for differentiating acoustic emissions caused by rock fracture from those caused by extraneous noises must be found. Pattern recognition analysis may provide such a method. This paper presents the results of pattern recognition analysis to make two types of differentiations: acoustic emissions caused by crushing two types of minerals (quartz and chrysocolla) and those caused by two extraneous noise sources, and acoustic emissions produced by each mineral.

Jan 1, 1982

By J. L. Lamont, W. Crafts

Studies of the effect of composition of steel on hardenability by Grossmann,' and as-quenched hardness by Field2 and by the authors, have made it possible to predict the results of quenching when the composition and cooling rate are known In order to extend the application of the hardenability calculation to the quenched and tempered condition in which steel is finally used, a survey has been made of the hardness changes caused by tempering. From this study a method has been developed for the prediction of hardness and tensile strength of steel in the tempered condition. The method of calculation was developed from Rockwell C hardness tests on quenched and tempered Jominy specimens and is expressed in Rockwell C hardness units. It is of an additive type in which the degree of softening from as-quenched hardness is estimated. Tem-pred properties may be calculated within about plus or minus 5 Rockwell C hardness or plus or minus 15,000 lb. per sq, in. tensile strength. This degree of accuracy is less than that necessary for the control of heat-treatment, but is adequate for the comparative evaluation and selection of alloy steels. The formula indicates that tempered hardness is primarily dependent on as-quenched hardness and, as in the hardening reaction, the progress of tempering is controlled mainly by the carbon content. Alloys tend to retard softening by a secondary hardening mechanism in which the alloy appears to migrate from ferrite to the carbide phase. The factors for the effects of alloys in tempering vary so much from the effects of alloys in hardening that different steels of equivalent hardenability may, after like heat-treatment, differ considerably in tensile strength. Procedure In developing the method for calculating tempered Rockwell C hardness, simple and complex steels were tested over a range from 0.08 to 0'65 per cent carbon and up to 2.68 per cent manganese, 2.18 silicon, 3.50 chromium, 4.94 nickel, and 1.06 molybdenum. The steels were made as small induction-furnace heats at the Union Carbide and Carbon Research Laboratories, Inc' The accuracy of the method was finally checked on a variety of carbon, low-alloy and high-alloy types of heat-treating steels produced under commercial conditions. The method was based on a study of tempered Jominy bars, and its validity was tested by correlation with the center hardness and tensile strength of oil-quenched and tempered bars from 1/2 to 4 in. in diameter. The method of calculation was derived from the differences in Rockwell C hardness between as-quenched and quenched and tempered Jominy specimens. Prenormalized Jominy hardenability speci-menS quenched from a normal temperature for austenitizatios were used to obtain a range of as-quenched Rockwell C

Jan 1, 1948

By W. Crafts, J. L. Lamont

Studies of the effect of composition of steel on hardenability by Grossmann,' and as-quenched hardness by Field2 and by the authors, have made it possible to predict the results of quenching when the composition and cooling rate are known In order to extend the application of the hardenability calculation to the quenched and tempered condition in which steel is finally used, a survey has been made of the hardness changes caused by tempering. From this study a method has been developed for the prediction of hardness and tensile strength of steel in the tempered condition. The method of calculation was developed from Rockwell C hardness tests on quenched and tempered Jominy specimens and is expressed in Rockwell C hardness units. It is of an additive type in which the degree of softening from as-quenched hardness is estimated. Tem-pred properties may be calculated within about plus or minus 5 Rockwell C hardness or plus or minus 15,000 lb. per sq, in. tensile strength. This degree of accuracy is less than that necessary for the control of heat-treatment, but is adequate for the comparative evaluation and selection of alloy steels. The formula indicates that tempered hardness is primarily dependent on as-quenched hardness and, as in the hardening reaction, the progress of tempering is controlled mainly by the carbon content. Alloys tend to retard softening by a secondary hardening mechanism in which the alloy appears to migrate from ferrite to the carbide phase. The factors for the effects of alloys in tempering vary so much from the effects of alloys in hardening that different steels of equivalent hardenability may, after like heat-treatment, differ considerably in tensile strength. Procedure In developing the method for calculating tempered Rockwell C hardness, simple and complex steels were tested over a range from 0.08 to 0'65 per cent carbon and up to 2.68 per cent manganese, 2.18 silicon, 3.50 chromium, 4.94 nickel, and 1.06 molybdenum. The steels were made as small induction-furnace heats at the Union Carbide and Carbon Research Laboratories, Inc' The accuracy of the method was finally checked on a variety of carbon, low-alloy and high-alloy types of heat-treating steels produced under commercial conditions. The method was based on a study of tempered Jominy bars, and its validity was tested by correlation with the center hardness and tensile strength of oil-quenched and tempered bars from 1/2 to 4 in. in diameter. The method of calculation was derived from the differences in Rockwell C hardness between as-quenched and quenched and tempered Jominy specimens. Prenormalized Jominy hardenability speci-menS quenched from a normal temperature for austenitizatios were used to obtain a range of as-quenched Rockwell C

Jan 1, 1948

By D. E. Hawk, R. F. Burdyn, F. D. Patchen

Earlier work on a mud separator for barite recovery is extended to the design and construct ion of a rugged field unit. Problems associated with scale-up for field use include the me of dilution water and its effect on capacity, power requirements and pressures developed. Equations for these quantities are derived and applied in maximizing the beneficial effects of dilution and minimizing the power required. Tests on the full-size rotor show that its performance can be predicted by theory. The completed unit is compact and lighter than current decanting types. Its capacity is from 10 to 22 gal/min with corresponding barite recovery efficiencies of 92 to 86 per cent. INTRODUC'TION In an earlier publication a new type of centrifugal device was described for solid-liquid separations.l In that paper an operating equation was derived, and its validity demonstrated in laboratory scale experimentation. Some of the features apparent in this new device seem particularly well suited to the conservation of barite in field drilling-mud systems, hence the development was extended to the design and construction of a field unit. In the present paper the design problems associated with scale-up are considered. A full-scale, rugged self-contained field unit is described, and test results discussed which verify that the performance of the large field unit can be described by a simple operating equation. PRINCIPLE OF OPERATION OF SEPARATOR In principle, the new device is simply a perforated cylinder rotating within a body of fluid which is contained within a stationary case, as in Fig. 1. The frictional drag generated by the rotating cylinder causes part of the fluid to rotate. At the surface of the cylinder, assuming no slip occurs, the angular velocity of fluid and of the cylinder are identical. If there are suspended particles present of greater density than the fluid, the centrifugal force acting on these particles causes them to move radially away from the cylinder at some velocity vp . Where the Stokes settling equation holds, this velocity may be expressed as:2 d2 ?p rw2 If the case is provided with openings at both ends, a suspension can be pumped in at one end at a fixed rate. Part of the suspension can then be removed at a fixed rate at the other end of the case as underflow, and the remainder forced through the perforations and hollow shaft of the rotor to appear as effluent, also at a fixed rate. The radial component of the flow velocity of this stream as it reaches the rotor surface, is simply effluent flow rate divided by cylindrical surface area: Because up is a function of particle size, for some particular particle size, the velocities vp and v, will be equal in magnitude. This is defined as the critical particle size and represents the size above which all particles appear in the underflow and below which all particles appear in the effluent. For this equilibrium condition at the rotor surface, Eqs. 1 and 2 combined give

Jan 1, 1966

By John Philip Zannaras

John Philip Zannaras (Registered Professional Engineer, Congress, Ariz.)- The authors show in their [Fig. 4] the cumulative results of grinding with two sizes of bails, one 30 mm and the other 20 mm. The Gaudin-Meloy probability for breakage for a single fall used by the authors in their paper is given by their [Eq. 6]. Another form of [Eq. 6] is given by Gaudin-Meloy in their paper as follows: [ ] From the definition of A given by Gaudin-Meloy it is obvious that A30 is greater than A., it therefore follows from the foregoing equation that according to the Gaudin-Meloy formula the probability of breakage for a single fall of all the balls in the 20-mm experiment was more than 2.25 times the probability of breakage in a single fall of all the 30-mm balls which is contradicted by the authors' experimental evidence in [Fig. 4] in which is shown that much more grinding took place with the 30-mm balls. In fact the authors present convincing evidence that the Gaudin-Meloy work is erroneous because their work is based only on a geometric configuration and on ambiguous and uncertain definition of A and disregards the fact that the distribution of fracture depends on other important and indispensable factors including the intensity of stress caused on the feed grain by the balls. That there is an immense and chaotic variation of stresses caused on the feed grains by the balls is shown by a formula, derived by this writer and published in 1955. The derivation of this formula is given in the Appendix of this discussion; it contains the variables in the operation of ball mills and is based on the science of mechanics-not on probabilities. [ ] where T is the unit stress in pounds per square inch produced by the moving load, h is the height in feet through which P has fallen, E is the modulus of elasticity of the rock, P is weight of one ball, and L is the size of the grain (assumed to be a cube of side L). It will be shown by this writer's formula that when a 30-mm ball strikes any size of feed grain it will cause 1.837 times higher stress than the 20-mm ball when striking the same size grain. It will be shown that when the 30-mm ball or the 20-mm ball strikes a feed grain of 0.1 mm it will cause 90 times more stress on the grain than when it strikes a 2-mm grain.

Jan 1, 1974

By Samuel B. Christy

" The man is always greater than his work." The training of the men who are to develop the mineral resources of the world is the most important problem connected with mining engineering. It becomes ever more important to civilization as the mineral wealth of the earth approaches exhaustion. I have therefore decided to consider a few of the more important problems arising in the training of the mining engineer, and especially those arising in America. , The Peculiar Nature of Mineral Wealth. Mining and Agriculture are the two fundamental arts. Without the latter our existence would be precarious; without the former, our civilization impossible. Agriculture furnishes that regular supply of food and raiment which leads to the growth of large communities in which cultivated leisure first becomes possible; while mining furnishes the metallic thread from which is woven that complex fabric we call civilization. But in these two arts the conditions for success are widely different. Most of the crops that the farmer reaps may be harvested year after year, and the proper fertilizers being added, he may continue the annual harvest indefinitely, while, as a result of cultivation, his farm becomes yearly more valuable. But the crop the miner reaps can be harvested but once in the history of the race. Our mineral wealth has taken unknown ages to mature in the bosom of the earth. The ripened fruit can be plucked but once. There are no fertilizers for worked-out mines. It never pays to work over a mine that has been

Jan 1, 1906

By Gerhard Derge, Arthur H. Grobe, Harold Markus

The high corrosion resistance possessed by tin under most circumstances, combined with its generally satisfactory appearance and useful physical properties, has led to many and varied uses for the metal. These uses have been partly limited by the fact that tin is an expensive metal, therefore many applications have been developed in which tin has been employed in combination with lead, either by coating, as in tin-lined collapsible tubes, or by the formation of alloys containing various proportions of tin-rich and lead-rich phases, as tcrne plate. A detailed knowledge of the corrosion characteristics of the tin-lead couple therefore is of general interest and has become specially important at the present time, when every effort is being made to conserve tin as much as possible. The present study has been limited to carbonate solutions with a pH range from 8.4 to 11.2 so that the results may be related to earlier work on the corrosion of tin and its alloys. 1-3,6 In these papers, the effects of a number of anion and cation additions to these solutions have been observed. Apparatus and Method The electrodes for the corrosion cell were cut from rolled sheet about 1/16 in. thick. The length of all specimens was held constant at 7 in., while the width was varied from M to 2 in. These electrodes were fastened to brass electrode supports, which were attached to rubber stoppers fitting into tall-type one-liter Pyrex beakers that contained the electrolyte. The lead electrodes were prepared from Omaha pig* and the tin was rolled from a slab of Chempur.† After cutting to size, the sheets were polished with No. I emery paper and cleaned with carbon tetrachloride. The edges, back and upper parts of the specimen were coated with a synthetic lacquer, which was supplemented with beeswax for the lead electrodes. The binding posts were coated with beeswax after the electrodes had been clamped. The pH of the electrolyte was controlled by adjusting the ratio of carbonate to bicarbonate. Approximately 600 ml. of electrolyte was used in each beaker. The entire assembly was placed in an oil bath thermostatically adjusted to operate at 30°C. + 0.1". Potentials were measured against a saturated calomel electrode connected to the cell by an agar-agar salt bridge. The carbonate solution used in the salt bridge was the same as that used in the corrosion cell. Currents were measured with a milliam-

Jan 1, 1942

By Harold Markus, Arthur H. Grobe, Gerhard Derge

The high corrosion resistance possessed by tin under most circumstances, combined with its generally satisfactory appearance and useful physical properties, has led to many and varied uses for the metal. These uses have been partly limited by the fact that tin is an expensive metal, therefore many applications have been developed in which tin has been employed in combination with lead, either by coating, as in tin-lined collapsible tubes, or by the formation of alloys containing various proportions of tin-rich and lead-rich phases, as tcrne plate. A detailed knowledge of the corrosion characteristics of the tin-lead couple therefore is of general interest and has become specially important at the present time, when every effort is being made to conserve tin as much as possible. The present study has been limited to carbonate solutions with a pH range from 8.4 to 11.2 so that the results may be related to earlier work on the corrosion of tin and its alloys. 1-3,6 In these papers, the effects of a number of anion and cation additions to these solutions have been observed. Apparatus and Method The electrodes for the corrosion cell were cut from rolled sheet about 1/16 in. thick. The length of all specimens was held constant at 7 in., while the width was varied from M to 2 in. These electrodes were fastened to brass electrode supports, which were attached to rubber stoppers fitting into tall-type one-liter Pyrex beakers that contained the electrolyte. The lead electrodes were prepared from Omaha pig* and the tin was rolled from a slab of Chempur.† After cutting to size, the sheets were polished with No. I emery paper and cleaned with carbon tetrachloride. The edges, back and upper parts of the specimen were coated with a synthetic lacquer, which was supplemented with beeswax for the lead electrodes. The binding posts were coated with beeswax after the electrodes had been clamped. The pH of the electrolyte was controlled by adjusting the ratio of carbonate to bicarbonate. Approximately 600 ml. of electrolyte was used in each beaker. The entire assembly was placed in an oil bath thermostatically adjusted to operate at 30°C. + 0.1". Potentials were measured against a saturated calomel electrode connected to the cell by an agar-agar salt bridge. The carbonate solution used in the salt bridge was the same as that used in the corrosion cell. Currents were measured with a milliam-

Jan 1, 1942

By Charles B. Dudley

DEAR SIR: It is now nearly three years since my first report to you on the subject of steel rails was written. That report, as you will remember, dealt principally with the question of the relation between the chemical composition and physical properties of steel rails end their power to resist crushing and fracture in actual service. Other matters were referred to or touched upon in that report, but the main question was, Why do some rails crush or break in service while others do not? Yon will doubtless remember that the principal conclusion arrived at was, that the softer rails are less liable to Crush or break in service than the hard ones. Or, in other words, so far as conclusions could be drawn from the chemical analysis and physical test of 25 samples of steel rails which had actually been in service, these conclusions were that those rails which have the smaller amounts of carbon, phosphorus, silicon, and manganese are less liable to crush or break in service than those which have larger amounts of these elements. Or, again, looked at in the light

Jan 1, 1881

By Sidney Powers

CONTENTS PAGE Distribution of fields 4 History of development 6 Origin of oil 7 Structure,, accumulation and migration 8 Reservoir rocks 9 Methods of drilling and exploration to Oil-field statistics 12 Description by regions: United States: Appalachian region 12 East-central states 17 Kansas 18 Oklahoma 19 Texas 24 Arkansas 32 Louisiana 33 Mississippi -.. 34 Rocky Mountain region 34 California : 37 Canada 41 Mexico 43 Cuba 46 Bibliography 46 THE purpose of this brief account of the occurrence of petroleum in North America is to make available to those who have a knowledge of geology, but who are not engaged in the petroleum industry, a few salient facts about the location of oil and gas fields, their productivity, the important structural types of accumulation and the age of the rocks containing petroleum. A few useful data and statistics are furnished, yet not complete statistics that are available elsewhere. Geology has been treated in simple terms because the reader is presumed to have little interest in the names of formations and of oil sands. Mineral deposits are more or less analogous. Whether oil or metals, minerals are found in rocks, largely in sedimentary rocks which carry water or have at one time carried it. A genetic or accumula-

Jan 1, 1931

By A. K. Mukherjee, J. E. Dorn

A modified Peierls model is Presented for the rationalization of the asymmetric plastic behavior of single crystals of bcc metals. The model assumes that the asymmetry of slip arises from a tendency toward asymnetric splitting of the a/2[111] screw dislocation. The approach differs from former theories however insofar as it assumes that the splitting is so minor ttut only the core energy is modified and that no real partial dislocations exist. As a consequence, the concepts of a line energy of a partial dislocation, interaction between partial dislocations, constriction energies, and stacking fault energies are not invoked. Instead the present analysis is based on a specialization of the Peierls mechanism which assumes an asymmetric dislocation core which is modified by the effective stress and permits cross slip. The theoretical predictions on the stress-temperature -strain rate and orientation relationship agree qualitatively with the limited experimental data that are currently available. Additional experimental work over wider ranges of conditions is suggested to provide more complete evaluation of the possible validity of this theory. RECENT experimental investigations on the low-temperature thermally activated deformation of bcc metals have confirmed the existence of several unique orientation effects. These will be described with the aid of the standard stereographic projection shown in Fig. 1. If slip were determined exclusively by crystal symmetry, the deformation characteristics would be symmetrical about X; = 0 and independent of whether the specimen were subjected to a tension or a compression stress, regardless of what combinations of slip planes might be operative. Experiments, however, reveal that neither of these symmetry based predictions are valid. A schematic representation of the commonly observed asymmetry of both the yield stress and the plane of slip is shown in Fig. 2. A reversal of the direction of stressing results in an inversion of the asvmmetric behavior. 1) Asymmetry bf Yielding. A detailed investigation on the asymmetric yielding in an Fe-2.7 pct Si alloy was repoEted by Tabka, Tikeuchi, and Furubayashi,1 Similar trends have been observed by Keh and Nakada on iron,' Stein on molybdenum,3 Bowen, Christian, and Taylor4 on columbium, Sherwood, Guiu, Kim, and pratt5 on Ta, Cb, and Mo. The degree of asymmetry not only depends on the atomic number and alloying but, in all cases that have been examined, it also increases with a decrease in the test temperature. 2) Asymmetry of the Slip Plane. Asymmetric $I-~: curves of the type shown in Fig. 2 have been found for several Fe-Si alloys6-8,1 and columbium.4 There is general agre_ement that near X: = 30 deg slip occurs by the [111](211) mode so that ?1 = 30 deg. As X; decreases it appears that [111](211) to [111](101) cross slip takes place leading to slip band traces on intermediate planes. And as xi approaches 0 deg, sharp

Jan 1, 1970