Search Documents

By R. Maddi, I. R. Kramer

C. S. Roberts (Dow Chemical Co., Midland, Mich.)— In this study we have seen another example of how modern electronic instrumentation can be of great value to metallurgical research. The authors have shown much ingenuity in their experimental work. However, I wish to point out that anelasticity theory tells us that we must be cautious when we use pulse methods for measurements which are to be correlated with knowledge of static stress-strain behavior. The basic stress calibrations used by the authors depend on the use of static moduli combined with the pulsed strains. No recognition of a possible modulus defect has been indicated. The general agreement of critical resolved shear stresses may indicate that a

Jan 1, 1953

By Frank H. Macpherson

Few people realize the tremendously important part that Saline and Pulaski Counties in central Arkansas have played in the winning of the war The present favorable war situation might have been very different if we had not had the bauxite produced during the past two years from these two small areas, a total Of about 15 square miles. As a general statement, it can be said that the Arkansas bauxite deposits are, individually, relatively small, irregular in thickness, somewhat scattered and, therefore, compared with coal or iron-ore or open-pit copper deposits, relatively ill adapted to a rapid and drastic expansion in output. A few years ago it would have seemed an impossibility for these two counties to produce over six million long dry tons of bauxite in one year. However, with the cooperation of the operators, that is what happened in 1943, when the state of Arkansas achieved the seemingly impossible with a production of 6,020,684 1 long tons (dried equivalent) of bauxite ore during the calendar year, compared with an average annual production of 323,7252 tons in the period 1931 to 1941. It became apparent early in the year '94' that the united States soon might be drawn into the war, and, therefore, that an immediate study of the domestic metal situation was necessary. Aluminum is by far the most important metal used in the manufacture of aircraft and many other implements of war and it was evident that there would have to be a tremendous increase in the domestic production of bauxite, which is practically the only present source of this metal. AS more than 95 per cent of the known bauxite reserves of the United states was in Arkansas, careful preliminary studies were made in that state by representatives of the united States Bureau of Mines, the United States Geological survey and the War Production Board in the summer of 1941 Reserves in other states also were studied. The result of these studies was a recommendation by the War Production Board that mining in the bauxite.producing areas of Arkansas be geared for maximum production, in order to supply sufficient ore for this country's war requirements and, if necessary, to supply the war needs of Canada as well. The annual goal of eight million long tons (dry weight) set for Arkansas by the war Production Board was exceeded in 1943, when in August the output reached a rate equivalent to more than 8,300,000 long tons, dry basis. Because of the comparatively small tonnage of bauxite reserves, Congress appropriated funds for an extensive drilling program to be carried out by the Bureau of Mines in cooperation with the Geological Survey. Drilling began in May 1942 but owing to delay in delivery of drills, and trucks upon which the drills were mounted the program did not get into peak operation until early in 1943. By the end of July 1944, the Bureau of Mines records indicated an addition to the Arkansas reserves of 10,000,000 long tons (wet basis) in place,

Jan 1, 1946

By B. C. Allen, W. D. Kingery

Surface tension and its temperature dependence have been determined for pure liquid Fe, Cu, Co, Ni, and Sn and for Fe-C, Co-C, and Ni-C alloys. The temperature coefficient of surface tension is negative for all these liquids. The surface tension and wetting behavior of tin and tin-titanium alloys on A120,, Si,N,, MoSi,, and Sic, as well as the behavior of titanium-containing nickel alloys on A1 20, have been determined over a wide temperature range. For all the solids investigated titanium additims markedly lower the contact angle. Some limits for the solid-surface energies have been calculated from liquid surface tension and wetting behavior. SURFACE tension and interface energy are important variables in a number of metallurgical and ceramic phenomena, and have been discussed at some length in connection with determining micro-structure of polyphase systems,' solid-state sintering,' thermal etching of grain boundaries, heats of solution and fine powders,'1 grain-growth phenomena,' the mechanical behavior of fine foils and fibers, nucleation, soldering and brazing,' and other phenomenz of academic or practical interest However, until recently few quantitative data have been available for high-temperature systems. Among available data are some indicating positive temperature coefficients for the surface tension of liquid copper,*,11,'2 cast iron,l3 and iron-carbon14 alloys. Although carbon was found to be not surface active in iron at 1570" some preliminary studies had indicated the possibility of a positive temperature coefficient for the eutectic composition at lower temperatures.16 One part of the present study has been largely concerned with determining the temperature coefficient of surface tension for several metals at elevated temperatures, In addition to surface-tension studies, the wetting behavior of alloys containing titanium has been investigated over a wide temperature range. Previous measurements indicated that titanium was selectively adsorbed from nickel at a liquid nickel-solid alumina interface,17 and the use of titanium hydride or titanium-alloy techniques for metal-ceramic soldering is well known. In the present study, previous data have been extended to new alloy systems, and measurements have been carried out with other oxidation-resistant ceramics. EXPERIMENTAL The sessile-drop method was employed to measure liquid surface tension and contact angle between liquid and solid, utilizing apparatus and techniques which have been described previously.'g The shape of a sessile drop depends on equilibrium between forces of surface tension tending to form a spherical surface of minimum area and forces of gravity tending to flatten the drop. Typical sessile drops are shown in Fig. 1. From precise measurements of maximum drop diameter and drop height the surface tension and drop volume were calculated. Four solid materials were employed as supporting plaques for the liquid-metal drops. Aluminum oxide (99.9 pct, J, T. Baker, reagent grade) was pressed and sintered at 1800°C. Molybdenum-disilicide powder (99.0 pct, Electro Metallurgical Co.) was pressed and sintered at 1650°C. Plaques were cut from silicon carbide (99.4 pct, hot-pressed at Alfred University) and silicon nitride (95.1 pct, with Al, Fe, 0 as major impurities, Norton Co.) rods. All plaques were polished, cleaned, and dried prior to use. A number of metals and alloys were employed. Chemical analyses of vacuum-melted ingots of iron, nickel, cobalt (National Research Corp.), commercial nickel-base alloys, electrolytic copper (International Smelting and Refining Co.), and tin (Mal-linckrodt Chemical Works) are given in Table I. Alloys were prepared in the laboratory by vacuum melting the base metal with either titanium hydride (Metal Hydrides, Xnc.) or spectroscopic-grade carbon (National Carbon Corp.). Nickel-titanium alloys contained between 0.001 and 0.005 pct oxygen and the ferromagnetic metal-carbon alloys contained 0.001 pct. Cylindrical metal specimens (1 to 2.5 g) were machined and bevelled at the bottom to insure a uniform advancing contact angle on melting. Before use the samples were acid-etched, cleaned with acetone, and rinsed in petrol ether.

Jan 1, 1960

By M. C. Udy, P. C. Rosenthal

THE use of minute boron additions to steel has been given considerable attention in recent years. Comparisons made between boron-free and boron-containing heats of otherwise identical analysis have indicated, beyond a doubt, the potent effect of boron for increasing hardenability. The actual hardenability increase has been expressed as a multiplying factor, or in terms of the percentage of other alloying elements boron might replace, The present study presents the results of a systematic survey of. the use of boron as an addition to two types of alloyed steels and as a replacement for various percentages of molybdenum in these steels, Both cast and wrought steels of the two basic compositions were prepared. Molybdenum, because of its scarcity at the time the investigation was started, was selected as the element to be replaced by boron. Attention was also given to the effects of boron on other properties of the steels, particularly their notched-bar toughness, to investigate other advantages or limitations of this element as an alloy addition. EXPERIMENTAL WORK Steels Investigated The two basic compositions used in this survey of boron as a replacement for molybdenum are given in Table I. The cast steels were higher than the wrought steels in silicon content to improve the casting quality. [ ] Each of these base steels, both cast and wrought, was made with molybdenum contents of o, 0.10, 0.20, 0.30, or 0.40 per cent, the total comprising 20 steels. In addition, each of these 20 compositions . was prepared with boron additions in amounts of 0.0015, 0.003, and o,006 per cent as ferroboron; and in amounts of 0.002 and 0.005 per cent as two com¬mercial intensifier alloys, designated alloys A and B. The boron-treated steels totaled 100, and the entire series 120, Test Procedure Each steel was melted as an individual heat in a 50-lb., magnesia-lined induction furnace. Ingot iron scrap or mixtures of ingot iron and steel scrap were used for melting stock. Deoxidation was carried out in the furnace with o.10 per cent aluminum. The aluminum addition was

Jan 1, 1946

By George Rice

THE A.I.M.E. Ground Movement and Subsidence Committee, pro-posed in 1920, held its first technical meeting in February 1923, under the able chairmanship of Mr. H. G. Moulton. The following list of papers and discussions, indicating the scope of the problems and relation to various conditions and method of mining, were given at that meeting by the distinguished mining engineers: J. Parke Channing, on Subsidence at Miami, Arizona; Howard N. Eavenson, on Mining an Upper Bitu-minous Seam after a Lower Seam Has Been Extracted; J. J. Rutledge, on Subsidence in Two Oklahoma Coal Mines; Benjamin F. Tillson, on Caving Cracks at the Franklin Mine, New Jersey; Dr. F. W. McNair, on the Dome Theory; William Kelly, on disadvantageous effects in Mining and Back-filling Working Upward a Steep-Pitching Iron-ore Bed; Eli T. Conner, on the good results of Back-Filling by Hydraulic Means in Preventing Destructive Subsidence in the Anthracite District; Thomas H. Claggett, on the merit of Systematic Pillar Drawing in Preventing Cracks in an Upper Seam; Henry H. Otto, successful results in the anthracite district in Mining Lower Seams before Upper Seams; Douglas Bunting, on Leading Factors Incident to Successful Mining of an Overlying Seam; Edwin Ludlow, on there being "less damage to buildings when there was complete removal of coal with complete packing than when room and pillar is used without extracting the pillars"; Edward O'Toole on "bumps" in eastern Kentucky mines, which he thought were the result of geologic stresses: H. A. Buehler, on Upheaval of Surface in an Illinois Case in Advance of the Face; and R. Dawson Hall, on The Mechanics of Subsidence from Mining. The author of this paper discussed various Winds of problems of ground movement and subsidence in both metal mining and coal mining; the production of great landslides by workings near an outcrop, as at Turtle Mountain, Alberta, Canada; and general

Jan 1, 1939

By George Rice

THE A.I.M.E. Ground Movement and Subsidence Committee, pro-posed in 1920, held its first technical meeting in February 1923, under the able chairmanship of Mr. H. G. Moulton. The following list of papers and discussions, indicating the scope of the problems and relation to various conditions and method of mining, were given at that meeting by the distinguished mining engineers: J. Parke Channing, on Subsidence at Miami, Arizona; Howard N. Eavenson, on Mining an Upper Bitu-minous Seam after a Lower Seam Has Been Extracted; J. J. Rutledge, on Subsidence in Two Oklahoma Coal Mines; Benjamin F. Tillson, on Caving Cracks at the Franklin Mine, New Jersey; Dr. F. W. McNair, on the Dome Theory; William Kelly, on disadvantageous effects in Mining and Back-filling Working Upward a Steep-Fitching Iron-ore Bed; Eli T. Conner, on the good results of Back-Filling by Hydraulic Means in Preventing Destructive Subsidence in the Anthracite District; Thomas H. Claggett, on the merit of Systematic Pillar Drawing in Preventing Cracks in an Upper Seam; Henry H. Otto, successful results in the anthracite district in Mining Lower Seams before Upper Seams; Douglas Bunting, on Leading Factors Incident to Successful Mining of an Overlying Seam; Edwin Ludlow, on there being "less damage to buildings when there was complete removal of coal with complete packing than when room and pillar is used without extracting the pillars"; Edward O'Toole on "bumps" in eastern Kentucky mines, which he thought were the result of geologic stresses: H. A. Buehler, on Upheaval of Surface in an Illinois Case in Advance of the Face; and R. Dawson Hall, on The Mechanics of Subsidence from Mining. The author of this paper discussed various kinds of problems of ground movement and subsidence in both metal mining and coal mining; the production of great landslides by workings near an outcrop, as at Turtle Mountain, Alberta, Canada; and general

Jan 1, 1939

By Y. C. Liu, H. Margolin

Investigation of martensite habit plane in water-quenched Ti-Mn alloys was carried out in the range of manganese contents between 4.35 and 5.25 pct. On the basis of 22 measurements, the poles were observed to fall into two groups, indicating the existence of two habit planes. The Miller indices of the poles close to these two groups were found to be <334>ß and <344>ß. TITANIUM has an allotropic transformation at 882.1° ± 0.5C1 by which the high temperature ß (body-centered cubic) phase changes to a (hexagonal close-packed) phase. It is well known, as in the case of low carbon steel, that the unalloyed high temperature ß phase cannot be retained no matter how rapid the cooling rate. However, the addition of alloying elements usually lowers the transformation temperature continuously and stabilizes the ß phase to a temperature much lower than the allotropic transformation temperature in pure titanium. A typical example of this behavior is found with manganese-alloying of titanium. Fig. 1 shows the titanium-rich Ti-Mn equilibrium diagram as established by Battelle Memorial Institute.&apos; The addition of manganese lowers the ß transus line and the eutectoid reaction takes place at 550°C, the eutectoid composition being 20 wt pct Mn. However, upon quenching to room temperature from the ß field, the ß phase can be completely retained with much less manganese, see Fig. 2. If the composition is less than that required to stabilize the ß phase completely, a plate-like structure, similar to that of martensite in other alloy systems, appears as shown in Fig. 3. Much lower alloying content merely intensifies the amounts of these transformed structures, as shown in Fig. 4. This paper presents the results of an investigation of the habit plane of these martensitic structures in Ti-Mn alloys. Experimental Procedure Investigation of the pole of a given platelet was made using the two-surface method of analysis." In order that a given martensite trace on two surfaces be readily recognized both at low and high magnifications, it is desirable that only a small amount of martensite be present. From a review of the data obtained at Battelle Memorial Institute4 on quench hardening in Ti-Mn alloys and the results of Duwez" on transformation in Ti-MO alloys, it was decided that the most appropriate Ti-Mn composition for this study would be about 6 pct Mn. A group of alloys containing from 3 to 10 pct Mn was made to bracket this composition. The choice of the 6 pct alloy was apparently proper, since it was later learned that approximately 5.5 to 6 pct Mn is required to stabilize the ß phase on water quenching.

Jan 1, 1954

By A. S. Michaels, R. S. Timmins

A study of the effect upon oil recovery from an un-consolidated porous medium of chromatographic transport of selected reverse-wetting additives during water displacement is described. Flow tests were performed on hydrocarbon oil-saturated sand columns (containing connate water) into which small volumes of short-chain aliphatic amine solutions were introduced during water flooding. Concurrently, meusurements of oil-silica contact angles, oil-water interfacial tensions and oil-water distribution coefficients were measured us a function of additive concentration. Certain treatments were found to cause a slight reduction in oil recovery, while others produced a significant increase (up to 50 per cent of the normtzl irreducible rninimum oil saturation). Recovery eficiency was correlated most satisfactorily with the maximum degree of reverse wetting produced during additive transport; conditions which resulted in only mild oil wettability of the sand reduced recovery, while those favoring strong oil wetting increased recovery. A mechanism of reverse-wetting additive action during chromatographic transport is developed which ascribes the results to transient changes in oil-solid contact angle during flow, with consequent release of oil trapped by capillary forces. Implications of these observations with regard to improved waterflood efficiencies are discussed. INTRODUCTION The need for finding improved methods of oil production is amply illustrated by the large volume of oil considered economically unrecoverable by existing production practice. Water flooding has long been an excellent method of secondary recovery. However, even in those areas of a formation which are well swept by a water flood, 20 per cent or more of the oil remains trapped within the formation and is not recovered. This trapping of oil within the pores of the rock structure results primarily from interfacial forces. If these interfacial forces were altered, it is possible that the trapped oil could be released and recovered. The addition of surface-active agents to a water flood to alter the interfacial properties of the oil-water-solid system has received considerable attention as a method of increasing oil recovery. Studies of surfactant treatment have yielded varied and, in some cases, apparently conflicting results. Increased oil recovery using surface-active agents has been reported by a number of investigators. Others have found that use of surfactants in a water flood either has no effect upon oil recovery or decreases it. Since surface-active agents tend to alter the formation wettability and oil-water interfacial tension simultaneously, several investigators have tried to determine the role these two factors play in oil recovery. Data have been presented which indicate that the most desirable condition for the solid surface is strongly water-wet. Other results indicate that, although breakthrough recovery may be less, the greatest ultimate recovery is obtained when neutral wettability prevails.", " The desirability of low interfacial tension seems to depend upon the wettability of the formation. Reports of higher recoveries, when the interfacial tension is high in a water-wet system and low in an oil-wet system, are at odds with reports of increased recovery in water-wet systems when surfactants which decrease the interfacial tension are added to the water flood. A review of previous work studying the effects of using surface-active agents in a water flood shows that these agents produce widely different effects and that opinions as to the role of the various interfacial properties are diverse. The consensus, however, is that the interfacial properties are quite important in the displacement of oil from a porous medium by water. Even in those investigations where appreciable increases in oil recovery resulted from treatment with a surface-active agent, economic considerations generally made practical application of the treatment unattractive because surfactants tend to be adsorbed within the formation. This adsorption would necessitate using large quantities of surfactant if all of the flood water were treated to contain a given surfactant concentration, even if this concentration were quite low. Preston and Calhoun suggested that the principles of chromatography could be applied to the use of surface-active agents as a means of increasing oil recovery. A small volume of surface-active material is injec-

By Elbert Rowland

THE widespread interest in the alloys of beryllium with copper is due principally to the fact that certain compositions show very favorable precipitation-hardening characteristics and are, in fact, the strongest nonferrous alloys known at the present time. Investigations have been conducted by Masing and Dahl and others on the physical characteristics of ternary beryllium alloys, in an attempt to produce precipitation-hardening effects with a smaller amount of beryllium than that required in the binary copper-beryllium alloys (2.0 to 2.5 per cent Be). The results of these investigations show that ternary alloys of beryllium with Cu-Sn, Cu-Al and Cu-Zn, among others, exhibit promising improvements in physical properties after precipitation-hardening treatment and, while the increases in properties obtained are not as high as those realized from the binary copper-beryllium alloys, excellent properties are obtained with beryllium contents averaging about one-half the amount required in the binary alloys. This paper presents the results of an investigation of the equilibrium relations of certain alloys containing copper, tin and beryllium. The alpha-phase boundary of the ternary system is given for alloys containing from 0 to 1 per cent beryllium. The equilibrium conditions beyond the alpha-phase boundary are presented for alloys containing up to 32 per cent tin and 1 per cent beryllium. The data were collected by means of

Jan 1, 1935

By Donald Barton

THE theory of gravitation is based on Newton&apos;s law that any two bodies exert a mutual attraction which is proportional to the product of their masses and inversely proportional to the square of the distance between them; i. e., A = K MM/R2 (1) where K is a constant, M and m are the respective masses of the two bodies, and R the distance between them. In the earth&apos;s gravitational system, the earth is one of the bodies; the other may be any body within or without the earth. In theoretical discussions and calculations in regard to gravity, that other body usually is taken as a unit of mass: in the C. G. S. system, a body of one gram in mass. GRAVITY AND LEVEL SURFACES Gravity is defined in geophysics as the force of attraction exerted by the earth, towards itself, on a body of unit mass. The intensity of gravity is usually expressed in dynes of force or in centimeters of acceleration. In geophysical work in America, most commonly it is expressed in dynes (per gram) with the "per gram" understood and not directly expressed. In geophysical work in Europe, most commonly it is expressed in centimeters per second per second (cm./sec 2) and less commonly merely as centimeter-gram-second units (C. G. S.). At sea level, the intensity of gravity amounts very nearly to 980 dynes. The vertical is the direction along which the attraction of gravity is exerted at any point. In most cases, it is very nearly, but not quite, perpendicular to the earth&apos;s surface. The path that would be taken by a body falling freely through space toward the earth is vertical at each point and may be spoken of also as "the vertical," or as the line of the vertical, or as a line of force of gravity. At the earth&apos;s surface it commonly is very nearly, but not quite, a straight line.

Jan 1, 1928

By Augustus Locke

In 1900, when. the public first heard of "secondary enrichment," the Butte chalcocite seemed clearly supergene. Mining, through successive regions of leached capping, bonanza sulfide, and sulfide less rich, had paused at lean bottom levels which, though chalcocite-bearing, suggested the waning of copper. The deepest chalcocite, at 1500 ft., was yet too shallow to disturb the supergene hypothesis. But, with deeper mining, lean levels yielded to fat ones. Here and there they showed, within the same vein, an inverted distribution, chalcopyrite above and chalcocite below. To the miners&apos; astonishment, they carried chal-cocite, unaffected by cross faults, on an independent course to the depth of 2500 ft. The pattern of ore distribution, hitherto revealed only in fragments, was now appearing in perspective, and, in the depth of the chalcocite, was beginning to make Butte differ from all districts where the chalcocite is indubitably supergene. The idea of hypogene origin at length came into favor; by 1913, when Sales&apos; advocated this origin, the argument had become a powerful one. This argument rested on field evidence; but, already, there was beginning to emerge microscopic evidence not included in this argument. Especially pertinent was the proof that (1) the deep chalcocite lies in-mixed with bornite, often microscopic; (2) the deep chalcocite often replaces bornite; and (3) replacement of bornite by chalcocite is accomplished more easily than that of pyrite, enargite, or chalcopyrite. The microscopic evidence has been accumulating for ten years and it demands

Jan 1, 1924

By Donald Barton

THE theory of gravitation is based on Newton&apos;s law that any two bodies exert a mutual attraction which is proportional to the product of their masses and inversely proportional to the square of the distance between them; i. e., A = K MM/R2 (1) where K is a constant, M and m are the respective masses of the two bodies, and R the distance between them. In the earth&apos;s gravitational system, the earth is one of the bodies; the other may be any body within or without the earth. In theoretical discussions and calculations in regard to gravity, that other body usually is taken as a unit of mass: in the C. G. S. system, a body of one gram in mass. GRAVITY AND LEVEL SURFACES Gravity is defined in geophysics as the force of attraction exerted by the earth, towards itself, on a body of unit mass. The intensity of gravity is usually expressed in dynes of force or in centimeters of acceleration. In geophysical work in America; most commonly it is expressed in dynes (per gram) with the "per gram" understood and not directly expressed. In geophysical work in Europe, most commonly it is expressed in centimeters per second per second (cm./sec.2) and less commonly merely as centimeter-gram-second units (C. G. S.). At sea level, the intensity of gravity amounts very nearly to 980 dynes. The vertical is the direction along which the attraction of gravity is exerted at any point. In most cases, it is very nearly, but not quite, perpendicular to the earth&apos;s surface. The path that would be taken by a body falling freely through space toward the earth is vertical at each point and may be spoken of also as "the vertical," or as the line of the vertical, or as a line of force of gravity. At the earth&apos;s surface it commonly is very nearly, but not quite, a straight line.

Jan 1, 1928

By William G. Kranz

Discussion of the paper of WILLIAM G. KRANZ, presented at the San Francisco meeting, September, 1915, and printed in Bulletin. No. 101, May, 1915, pp. 927 to 930. M. PETINOT, Niagara Falls, N. Y. (communication to the Secretary*). -I have read this paper with considerable interest and agree perfectly with Mr. Kranz that steel for castings made in an electric furnace is not necessarily, because of that fact, all good steel, and also that the qualities which he mentions, such as absence of segregation, elimination of `sulphur, great tenacity, etc., can be obtained in an electric furnace if operated under proper metallurgical conditions. An unusually low content of sulphur in steel for castings is not, of course, an absolute necessity and the range of this element usually obtained in steel made in basic open-hearth furnaces is sufficiently low to meet all physical requirements. The main factor in making steel for castings, regardless of the process, is the complete deoxidation of the bath to prevent the formation of

Jan 12, 1915

By J. W. Rutter, K. T. Aust

The temperature dependence of the rate of grain boundary migration was measured in bicrystals of zone-refined lead containing from 20 to less than 1 ppm by wezght of tin. The apparent activation energy in the temperature range from 320" to 200oC is markedly dependent upon the solute tin concentration and upon the orientation relationship of the grains adjacent to the grain boundavy. The quantitative experimental observat~ons are compared with the predictions of various theories of grain boundary migration. In previous work.&apos;?&apos; the mobility of individual grain boundaries was studied as a function of impurity concentration and type of boundary. Grain boundary migration occurred at the expense of dislocation arrays which were introduced into the specimen during solidification. Boundary mobility in zone-refined lead at 300°C was markedly decreased by small additions of tin. 0.004 wt pct being sufficient to decrease the rate of grain boundary migration by a factor of 1000. The mobility of grain boundaries having polar orientation relationships near 38 and 22 deg about <Ill>, and 28 deg about <100>, was much less sensitive to tin concentration in the range studied. As a result, these boundaries have relatively high mobilities. The present paper is a continuation of the above study. Data are now presented on the temperature dependence of the motion of individual grain boundaries in zone-refined lead as a function of solute tin concentration and orientation relationship of adjacent grains at the grain boundary. The experimental observations are compared with the predictions of a number of theories of grain boundary migration3-8 which, prior to the present experimental investigation, could not be critically evaluated. EXPERIMENTAL PROCEDURE The striation or lineage structure of melt-grown single crystals of zone-refined lead, containing various additions of tin, was utilized to provide a driving force for grain boundary migration, as previously described.1,2 Each grain boundary under study separated the striated single crystal from another grain which was introduced by localized plastic deformation and recrystallization of a small region of the sample. The speed of migration of grain boundaries in dilute alloys of tin in zone-refined lead was investigated as a function of 1) tin concentration from < 0.0001 to 0.002 wt pct, 2) temperature in the range of 200" to 320°C, and 3) orientation relationship of the adjacent grains at the grain boundary. The substructure driving energy available for grain boundary migration was estimated to be about 4000 ergs per cu cm, within a factor of two, from specimen to specimen.&apos; The specimen dimensions, and growth and alloying procedures for the preparation of striated single crystals of lead of known tin composition, were as described previously.&apos; Each bicrystal was carefully wrapped in aluminum foil, and annealed in a well-stirred salt bath consisting of 50 pct NaNO2 and 50 pct KNO3, for known periods of time at a series of constant temperatures (*2°C). The grain boundary positions, before and after each anneal, were determined by etching lightly in a solution of 5 pct nitric acid in methyl alcohol, in order to follow the motion of the boundary and determine its rate of migration. Thus, the rate of motion of the grain boundary in a single specimen was measured at various temperatures. The above procedure was carried out for each grain boundary in seventeen different bicrystal specimens.

Jan 1, 1960

By W. H. Davitt

While it is true that taxes, especially income taxes, whether they be federal, state, or local, are not usually thought of as a "cost" of doing business, it is equally true that these tax costs do reduce the distributable profits just as much as the cost of power, supplies, or labor. Therefore, the consideration given to taxes is often as important as that given to other costs. Hopefully you will recognize that, within certain limits, taxes can be controlled to an economic advantage. The tax laws as now imposed are quite complex. Many of these laws and the regulations thereunder involve many factual determinations, technical considerations, and specialized valuations that can best be made by people trained in the specific area concerned. A substantial amount of a tax liability turns on the proper consideration given to issues involving facts and principles which are peculiarly engineering in nature. The importance of these "engineering" issues in tax administration has been significantly increased in recent years by our rapidly advancing technology, automation, stepped-up mineral and oil exploitation, new industries such as electronics and nuclear power, and the extension of percentage depletion to all minerals. These specialized requirements incorporated in the law are so technical that full consideration can not be given by people with a non-engineering background.

Jan 7, 1974

By M. B. Ramachandra Roa

This paper records the results of the earth resistivity surveys made in the Godavari River in connection with the Ramapadasagar project. After describing the topographical and geological features of the area, the results of the investigation at the several sites have been mentioned. Further, a detailed account has been given of the resistivity methods adopted, the apparatus used and the interpretation of the curves. The resistivity measurements carried out over the water course have been specially outlined, and a review of the verification of the electrical indications by drilling in a number of cases, has also been presented. Introduction The Government of Madras has under consideration the Ramapadasagar project which is estimated to cost some Rs.660,-000,000 (about two hundred million dollars). The most essential feature of this project is the construction of a high dam across the Godavari near Polavaram for impounding the waters of this great river of South India, whose maximum discharge is 2 million cu secs in flood time. It is estimated that when the proposed reservoir is constructed, about one million tons of rice could be produced annually under irrigation. To those who have had any acquaintance at all with the recent distressing famine conditions which India has passed through and is still undergoing, the Lounteous effects which this project will bring about to the country in the future, are obvious. In the region of the proposed reservoir, the river flows for several miles through a hilly tract, hemmed in between flanks of hard, solid rock; but the river bed is mostly sandy. A few bore holes put down in this sandy bed touched rock at a depth of 180 to 200 ft. The river bed is about jo ft above the mean sea level (m.s.l.) and the bedrock was found at —125 to —160 ft m.s.l. The crest of the dam is proposed at +162 ft m.s.l. The proposed dam mould therefore be about 120 to 130 ft above the river bed, and the foundations would have to reach down nearly zoo ft below the bed at the deepest part. A number of alternative sites were proposed for investigation, and it became necessary to quickly ascertain the bedrock topography at these sites. Dr. M. S. Krishnan,* who was consulted in the matter, furnished a detailed account of the geological features of the region and suggested a geophysical investigation which the writer carried out from February to April 1944, employing solely the electrical resistivity methods. The total length of the survey lines for the electrical measurements amounted to 62,600 ft and the number of resistivity determinations was about 2500. Altogether nine alignments for the dam were inten-

Jan 1, 1949

By R. V. Norris

IRving Ariel Stearns died at his home, 60 South River St., Wilkes-Barre, Pa., on Tuesday morning, Oct. 5, 1920, of pneumonia, after an illness of about a month. In his death, the Wyoming Valley loses one oflits most eminent and best loved citizens, and the loss of so strong a participant in the activities of the Valley will leave a gap most difficult to fill. Despite his more than three score and fifteen years, Mr. Stearns, at the time of his death, was president of the Wilkes-Barre City Hospital, Wyoming National Bank, and the Wyoming Historical and Geological Society, chairman of the Board of the Vulcan Iron Works, and a director of the Spring Brook Water Supply Co., and of the Wilkes-Barre Lace Manufacturing Co. Mr. Stearns came of New England stock, a descendant in the eighth generation of Charles Stearns who was admitted freeman in Watertown in 1646. Irving Ariel Stearns was born Sept. 12, 1845, in Rushville, N. Y., a son of George W. and Miranda (Tufts) Stearns. He was graduated from the Rensselaer Polytechnic Institute of Troy, N. Y., in the celebrated Class of 1868. After graduation, he was assistant professor of chemistry in charge of the analytical laboratory for a year, then went to Wilkes-Barre in 1869, as engineer in the office of R. P. Rothwell, at that time the leading mining engineer of the region. From 1871 to 1872, he was superintendent of the McNeal Coal & Iron Co. of Schuylkill County, Pa. and in 1872 succeeded to Mr. Rothwell&apos;s business when the latter became editor of the Engineering & Mining Journal of New York. From 1872 to 1885, Mr. stearns was in private practice as a mining engineer, handling a great amount of business in the anthracite region, including the building of the bridges at Shickshinny and Pittston, and the surveying and mapping of many of the individually operated mines. His practice extended throughout the country, with numerous examinations and reports upon mining properties in Pennsylvania, Virginia, West Virginia, Arkansas, Colorado, California, Wyoming, Idaho and Utah; he was responsible for the design and execution of the Lehigh Valley Railroad Co.&apos;s great Tifft Farm improvements at Buffalo, N. Y. including canals, docks, coal stocking plant, etc. He was commissioned Quartermaster of the Ninth Regiment, N. G. P., March 29, 1880, was promoted to Major on May 15, 1884, and resigned Apr. 1, 1885. He always retained his interest in the National Guard and was trustee and president of the Ninth Regiment Armory Association.

Jan 1, 1922

By R. V. Norris

IRving Ariel Stearns died at his home, 60 South River St., Wilkes-Barre, Pa., on Tuesday morning, Oct. 5, 1920, of pneumonia, after an illness of about a month. In his death, the Wyoming Valley loses one oflits most eminent and best loved citizens, and the loss of so strong a participant in the activities of the Valley will leave a gap most difficult to fill. Despite his more than three score and fifteen years, Mr. Stearns, at the time of his death, was president of the Wilkes-Barre City Hospital, Wyoming National Bank, and the Wyoming Historical and Geological Society, chairman of the Board of the Vulcan Iron Works, and a director of the Spring Brook Water Supply Co., and of the Wilkes-Barre Lace Manufacturing Co. Mr. Stearns came of New England stock, a descendant in the eighth generation of Charles Stearns who was admitted freeman in Watertown in 1646. Irving Ariel Stearns was born Sept. 12, 1845, in Rushville, N. Y., a son of George W. and Miranda (Tufts) Stearns. He was graduated from the Rensselaer Polytechnic Institute of Troy, N. Y., in the celebrated Class of 1868. After graduation, he was assistant professor of chemistry in charge of the analytical laboratory for a year, then went to Wilkes-Barre in 1869, as engineer in the office of R. P. Rothwell, at that time the leading mining engineer of the region. From 1871 to 1872, he was superintendent of the McNeal Coal & Iron Co. of Schuylkill County, Pa. and in 1872 succeeded to Mr. Rothwell&apos;s business when the latter became editor of the Engineering & Mining Journal of New York. From 1872 to 1885, Mr. stearns was in private practice as a mining engineer, handling a great amount of business in the anthracite region, including the building of the bridges at Shickshinny and Pittston, and the surveying and mapping of many of the individually operated mines. His practice extended throughout the country, with numerous examinations and reports upon mining properties in Pennsylvania, Virginia, West Virginia, Arkansas, Colorado, California, Wyoming, Idaho and Utah; he was responsible for the design and execution of the Lehigh Valley Railroad Co.&apos;s great Tifft Farm improvements at Buffalo, N. Y. including canals, docks, coal stocking plant, etc. He was commissioned Quartermaster of the Ninth Regiment, N. G. P., March 29, 1880, was promoted to Major on May 15, 1884, and resigned Apr. 1, 1885. He always retained his interest in the National Guard and was trustee and president of the Ninth Regiment Armory Association.

Jan 1, 1922

By C. H. Chou, Albert Sauveur

The following experiments were conducted in order to study the influence of the rate of cooling through and below solidification on the dendritic structure (macrostructure) and microstructure of some hypo-eutectoid steel. The steel selected was of commercial grade and had the following composition: C, 0.40 per cent.; Mn, 0.85; Si, 0.70; P, 0.099; S, 0.043. After melting in vacuum in an Arsem furnace, the various samples were allowed to solidify and to cool to room temperature as indicated in Fig. I. Samples were thus obtained representing all possible combinations of slow and fast cooling through the various ranges of temperatures indicated, namely: (I) zone of solidification or primary crystallization, (2) zone of granulation, and (3) zone of secondary crystallization. The location of the different temperature zones in the iron-carbon equilibrium diagram is shown in Fig. 2. The authors adopted Belaiew&apos;s notations. The designations of the various samples readily indicate their treatment, as will be apparent from Table 1. Sample SSS.—This sample was slowly solidified and cooled to room temperature in the crucible in which it was melted. The dendritic (macro) structure is shown in Fig. 3. The dendrites an: sharp and dis-

Jan 1, 1930

By Donald L. Ball

The equilibrium of boron nitride, gaseous nitrogen, and solute boron was investigated in Fe, Fe-C, and Fe-Si rnelts by the Sieverts technique. The free ellergy of dissociation of boron nitride, involving -the implied standard states, was evaluated in the range 1400" to 1600°C as: ?Fo = 38,000 - 23.5T, cal ber mole The solute-solute interaction coefficients eBB, ecB , and eg were determined as 0.058, 0.22, and 0.078, respectively. BORON is an important ingredient in some types of steel and cast iron. It was employed at a particularly high level, 0.01 wt pet, in the as-cast malleable iron "CentraSteel".1 In this material, the boron concentration was critical in order to assure graphite, and avoid primary cementite, in the as-cast structure. One possible function of the boron in this alloy was the nucleation of graphite through the agency of boron nitride, which, conceivably, precipitated from the melt during cooling. A research program was instituted to assess the validity of this proposed mechanism. The first undertaking, reported here, was a determination of the thermodynamic possibility of boron nitride precipitation. Data available in the literature on the activity coefficient of solute boron in iron-base melts are inadequate for the present purpose. They will be reviewed briefly, however, so that comparison can be made, when

Jan 1, 1968