Search Documents

By Walter R. Hibbard, Cyril Stanley Smith

IN 1929 one of the authors1 determined the constitution of copper-silicon-manganese alloys contailling over go per cent copper. Through a combination of circumstances the presence of the copper-silicon kappa phase was overlooked in both binary and ternary systems. In the binary system the omission has already been rectified.2,3 To establish the limits of this phase in the ternary system, the samples that had been heat-treated at the time of the original research have now been re-examined, using more careful technique. Full details of the compositions used and the temperatures and times of heat-treatment are to be found in the earlier paper.2 The etching reagent now used to distinguish the kappa phase had the following composition: hydrogen peroxide (30 vol.), 2o c.c.; water, 25 c.c.; 20 per cent potassium hydroxide solution, 5 c.c.; ammonium hydroxide (0.90 sp. gr.), 50 c.c. 'I'able I lists the newly observed structures. In virtually every case the constituents are the same as those previously recorded, except where kappa is now shown to be present as a result of the improved etching technique. X few other changes will be noted (No. 138 at 450°C., No. 147 at 550°C., Nos. 153 and 149 at 75o°C.). The change from liquid to beta in equilibrium with kappa in No. 137 at 800°C. is based upon newly heat-treated samples. The alloy is very near the solidus at 800°C. and probably there was a slight error in the old heat-treatment temperature. The isothermal phase diagrams shown in Figs. I to 6 were reconstructed on the basis of the new studies. The presence of manganese does not greatly change the composition limits of the kappa phase or cause the K-a + Y change to occur at a markedly different temperature. There is some uncertainty regarding the range of existence of beta, for alloys were not spaced very closely in composition. The proposed diagrams, however, are in accordance with the available experimental data and with the dictates of the phase rule. Theoretically necessary fields with no experimental points are delineated by dotted lines. The alpha boundaries at all temperatures are shown together in Fig. 7. This includes also some additional points on the alpha boundary at 300' and 350°C., which were obtained as a result of electrical-conductivity measurements. Two series of seven alloys with increasing manganese content but with silicon constant at 1.90 + 0.03 per cent or 2.42 ±. 0.05 per cent were cast in ingots of 3-in: diameter. These were hot-rolled, homogenized and drawn to wire, finished at 0.08-in. diameter with a 61 per cent reduction of area following annealing at 700°C. Conductivity determinations were made before and after annealing for 30 days at 300°C. or 21 days at 350°C. Figs. 8 and 9 show the change of conductivity produced by this annealing, plotted against manganese

Jan 1, 1942

By Leon Dominian

Page I. Introduction......................237 11. Coal..................239 (a) Western Asia Minor.........239 I-. Lignites of the Marmora-Bgean zone.239 2. The Black Sea basin.............241 (b) Eastern Asia Minor..........244 (c) Syria................246 (d) Mesopotamia................ 246 (e) European Turkey.'.....'..... 247 111. Oil and Allied Hydrocarbons...............248 (a) Early Use of Oil and Bitumen in Turkey........248 (b) Syria........................ 250 (c) Mesopotamia.................... 250 (d) European Turkey.................. 256 I. INTRODUCTION Apart from local needs in the country's development, the interest attached to Turkish fuels grows chiefly out of the importance of the railway industry in Asiatic Turkey. Geographical conditions make of the tracks in this region the most essential link in a chain of world-girdling lines. By its position Asia Minor can be likened to a bridge in the through routes destined to connect European factories with Asiatic and African markets. An uninterrupted right-of-way from points in central Europe to populous Indian cities must necessarily pass through the valleys of Anatolia. Crossing thence the Taurus Mountains, its natural passage is indicated as the Mesopotamian lowland and the shores of the Indian Ocean. Similarly, land connection between Europe and Africa can be obtained only by passage through Asia Minor, Syria and Palestine. The occurrence of fuel within an area of such significance from the

Jan 1, 1917

By Joseph G. Debanné

Foreword The three case histories and the liquid fuels planning scenario presented in this paper span a twenty year period, from the pioneering days of computers in the petroleum producing industry during the mid-fifties, to the energy crisis era of the seventies. Inasmuch as two of the main actors, Ian McKinnon and I, are featured in all three case histories, while I am currently involved in the fossil fuels scenario, this paper provides four related and personal spot readings along an evolutionary path: from the one dimensional technical domain to the multi-dimensional techno-socio-economic domain of computer applications in the petroleum industry. Coincident with this evolution in the direction of increasingly comprehensive and powerful computer applications, the evolution in hardware/software capability and in analytical power are also kept in perspective. The three case histories are: 1. The Bonnie Glen-Wizard Lake Case (Calgary, Alberta, 1955-1957); 2. The TransCanada-Great Lakes Gas Transmission Case (Ottawa-Washington, 1966); 3. The Westcoast Transmission - El Paso Pipelines Gas Export/ Import Case (Ottawa-Vancouver-Washington, 1966-1967). The liquid fuels planning scenario is a demonstration exercise rather than a case history; however, it represents an important point on the evolutionary curve and, provides a concrete example of tech-

Jan 1, 1977

By H. I. Meyer, D. F. Searcy

INTRODUCTION The analysls of our previous paper' on the behavior at two immiscible fluids separated by gravity into two dlstinct saturated zones in the porous medium was shown to be theoretically valid only if one of the two fluids was immobile. The practical problems associated with flow of both phases have so far been impossible of solution by these analytic methods. We, therefore, decided to resort to a simulator study to answer the following pertinent questions: 1. If the lighter fluid is produced from a point above the fluid-fluid interface, how long will it take for the heavier fluid to come up to the point where production of both fluids is taking place? 2. After steady-state two-phase production is established, what is the relative production rate of each phase, on what physical variables does this depend, and what are the boundary conditions at the outflow face? 3. A third question was at least partially answered in the course of this investigation: that of the shape of the interface under flow conditions. These questions are of fundamental importance in the fields of hydrology and the reservoir mechanics of oil and gas production. In order to simplify equipment used and still retain a fair physical representation of these phenomena, it was decided to use a Hele-Shaw type of analogy in which the flow took place between two vertically mounted pieces of plate glass. The advantage of this system is that it eliminates any surface effects between the matrix of the porous medium (e.g. packed sand) and also allows equilibrium conditions to be established more quickly. The principle disadvantage (apart from the obvious one of being one more step removed from the prototype) is that our equipment limited us to two dimensional flow studies. In spite of these limitations answers to the questions were obtained which seem adequate for our purposes. We would like to see more work of this nature done to verify and to improve our conclusions. DESCRIPTION OF EQUIPMENT AND PROCEDURE A drawing of the equipment used in this study is shown in Fig. 1. Fluid flow takes place between the two 36 in. x 12 in. pieces of plate glass held apart at the long edges by two spacers of cellulose acetate sheet (Kodapac IV) which is available in several thicknesses. This sandwich was clamped together by small c-clamps whose stress was distributed by long pieces of 3/8-in. keystock. Accurate spacing was obtained by tightening these clamps as indicated by micrometer measurements on the outside of the glass. At the upstream end of the plates a piece of 6-in. diameter pipe simulated an infinite reservoir, while at the downstream end a 2-in. Lucite cylinder with a small hole near the top of the flow region served to drain the fluid. Sealing was achieved by O-rings, the whole system being tightened by pressure on the Lucite tube provided by set screws (not shown in the drawing). The total head

Jan 1, 1957

By D. M. Jamieson, M. P. Pearse, E. R. A. Plumstead

In 1948 the shaft sinking record in the Republic of South Africa was held by the Van Dyk Consolidated Mines Ltd. for a ventilation shaft with a footage of 461 ft sunk during the month of August 1941. This record remained for some ten years; but in the ensuing nine years it was broken no less than 13 times. Table I gives shaft sinking records throughout the world for the 21 years, 1940 to 1960. History shows that the wide, deep, timbered rectangular shaft had passed its peak of popularity by 1948, although it still had a great deal to commend it, both from the sinking and operational points of view. In sinking, it is easy to clean manually, and water can be handled by bailing when wet ground has to be negotiated; its shape also lends itself to equipping concurrently with sinking. In operation it provides the most convenient "in line" hoisting arrangement, and if the ventilation requirements so demand, it offers the simplest solution in that it can be divided into upcast and downcast sections. Furthermore, in the case of a multi-level mine, the shaft compartments can be reduced conveniently if the full area of the shaft is not required to serve all levels.

Jan 4, 1963

By O. J. C. Runnalls, L. M. Pidgeon

J. M. Blocher, Jr. and I. E. Campbell (Battelle Memorial Institute, Columbus, Ohio)—Since the de Boer-Van Arkel process for making titanium metal involves a number of steps in a fairly compact unit, it is difficult to determine simply which of the steps is rate controlling. In any statement as to which step constitutes the rate-controlling process, qualifications appear to be in order. It is possible to design a reaction bulb in which any one of a number of steps is made to be controlling. I—With the filament removed some distance from the crude, as in the case of the authors' experiments, the interdiffusion of iodine and iodide may be controlling. 2—If, as is usually done, the crude metal is placed in a perforated cylindrical basket, or as a briquetted mass, in close proximity to the filament, the rate of deposition is increased (we obtained rates of deposition 5 to 10 times those cited in the authors' paper), and another rate-limiting factor, such as the reactivity of the crude, may take over. In this regard, we have noticed radically different rates of deposition with different crudes, and with crudes in various stages of exhaustion. 3—With a very reactive crude metal and with optimum practical geometry, still another process may be controlling. It is felt that this is a diffusion process in the immediate vicinity of the filament involving the fundamentally adverse situation of a net flow of particles away from the filament. The separate experiments on the reactivity of iodine with titanium are interesting but somewhat inconclusive. Data is still needed on the partial pressure of iodine in an operating decomposition bulb. A knowledge of the gradient of iodine partial pressure from the crude to the filament would be particularly enlightening. Optical absorption may be a useful technique here. Accurate measurements of the total pressure within a decomposition bulb under various conditions would be quite revealing. Preliminary measurements have been made at Battelle in following this line of attack. It is interesting to note that the authors' data on the temperature dependence of deposition rate indicate that the overall rate is not controlled by the kinetics of the decomposition reaction at the filament: TiI1 ? Ti + 4I Any reasonable estimate of the activation energy of this reaction would, if its kinetics were controlling, dictate a much greater temperature dependence than is observed here. The authors apparently attribute the drop in deposition rate (eventually to zero) with increased TiI4 pressure solely to a decrease in diffusion rate. However, there is an equilibrium factor involved here that must not be overlooked. As the partial pressure of TiI4 is increased, a point is reached where, due to the competing reaction of the tetraiodide with titanium to form lower iodides, the equilibrium partial pressure of titanium is reduced to the point that it equals the vapor pressure of titanium at the filament temperature and the deposition rate falls to zero. This effect would

Jan 1, 1953

By Pual M. Tyler

BLIZKRIEG tactics in the present war have consumed metals on such a profligate scale that some of the best-laid procurement plans for civilian and military needs of even a year ago seem in retrospect incredibly meager. Conservation of raw materials has reached an all-time climax in Germany, where metals are worth more than human life and throwing away an empty toothpaste tube may be legally punished by death. Even the United States and the British Empire, proud masters of nine tenths of the world?s known mineral reserves and processing plants, are being driven to metals and feverishly expanding production facilities that not long ago were deemed overbuilt. After the war is over and inevitable postwar readjustments are completed, it is reasonable to expect that purchasing power ? or at least the ability to procure the comforts and luxuries of life ? will be distributed among vastly larger population than ever before, accelerating the rising trend in demand for industrial raw materials in ever greater quantity and variety.

Jan 1, 1942

By R. J. Sherman, M. R. Achter

Creep rates have been measured for nickel at 1200°F in air and in vacuum, and related to the depth of surface cracks in the specimens tested in the two environments. The surface cracks were observed to grow faster in air than in vacuum in both short-time and long-time tests. Crack depths, however, could be correlated with creep rates only in the short-time tests. Although no cracks were observed in a relatively brittle Ni-Cr-A1 alloy creep tested at 1300°F, the appearance of alloy specimens fractured after interruption in creep indicated that there was a decrease of intergranular cohesion resulting from the diffusion of atmospheric gases into grain boundaries. PREVIOUS investigations1-3 have demonstrated that the effect of atmosphere on the high-temperature strength of nickel and nickel-base alloys may be reversed by changes in the stress or temperature of the test. At high stress and low temperature the creep-rupture life is longer in vacuum than in air, while at high temperature and low stress the relative strengths are reversed. A mechanism to explain this behavior was proposed based on two competing processes. Oxidation hardens and strengthens a metal, but adsorption of gas, by lowering surface energy, reduces the work required to propagate an intergranular crack. The controlling process is determined by temperature and stress. Basic to this mechanism is the concept that environment determines the ease of propagation of intergranular cracks and thus affects creep rate and rupture life. To explore the mechanism in greater detail, this investigation was undertaken to determine the effect of atmosphere on crack initiation and propagation rates in nickel1 and a relatively brittle Ni-Cr-A1 alloy.3 EXPERIMENTAL PROCEDURE The materials were the same as used previously. Nickel of 99.8 pct purity had the following impurity content: 0.02 pct Co, 0.03 pct Fe, 0.02 pct Mg, 0.03 pct Si, and 0.008 pct C. Rods were cold swaged from 1/2 in. to 3/8 in. in diam and machined into speci- mens with gage sections 1/4 in. in diam by 1-1/4 in. long. They were annealed in vacuum at 1600" F for 1 hr to achieve a grain size of 0.07 mm. The alloy was composed of 19.1 pct Cr, 3.6 pct Al, 1.7 pct Si, 0.57 pct Fe, 0.10 pct Mg, 0.027 pct C, 0.004 pct S, and the balance Ni. Sheet specimens of 0.500-in. width and 1.25-in. gage length were machined from 0.033-in.-thick strip and annealed in vacuum at 2000° F for 2 hr, resulting in a grain size of 0.036 mm. Large amounts of an intergranular phase were introduced as a result of the anneal. Creep tests on both materials, using equipment previously described by Shahinian; were conducted in air and in a vacuum of 1 x 10-5 mm Hg. They were continued to rupture and interrupted at various stages of the test. Although extensions were measured from dial gage readings of movement of the lever arm, it is considered that valid comparisons of creep rate may be made in this manner.l Two parameters were measured metallograph-ically* on longitudinal sections of nickel specimens interrupted during creep—the mean depth of surface cracks 2, and the density n as the number of cracks per unit length of surface. They were combined into one parameter by the relation p = n-d [1] As used here, p is equal to the total of crack depths per unit length of surface. RESULTS Nickel. It is well known that the incidence of intergranular cracking is increased with increasing rupture life. Indeed, it is evident in Tables I and I1

Jan 1, 1962

By Chu-Phay Yap

This is the first of a series of theoretical papers on the iron-carbon system. A simple critical analysis of the ordinary constitution diagram of the iron-carbon system yields valuable information regarding the nature of the equilibria in the liquid and solid states. It is shown, for example, that the solute in the melt is Fe3C, but in solid Fe (austenite) the solute is carbon. The thermodynamic laws of the depression in the freezing point of solid solutions have been developed and discussed. Using the usual method of plotting the logarithm value of the concentration of the solvent (in this case, the ratio of concentrations of the solvent in the liquid and solid phases) against 1/T, curves are obtained. A rigorous thermodynamic analysis of these curves has been shown to yield considerable information regarding the internal equilibria of the system, with which the phase rule does not deal altogether. In this way, it is shown again that the solute in the melt is Fe3C, but in the solid rFe the solute is carbon. Various heats of reaction (fusion and transition) and other thermal data have been derived: and discussed with a view to correlating the conflicting experimental data obtained by different investigators of the system.

Jan 1, 1931

By J. B. Newsorn

VERTICAL SHAFTS in the United States have heretofore been sunk by blasting and mucking. The blasting leaves uneven, shattered walls which usually must be supported. Even though the walls will stand, shaft lining is needed to furnish supports for the cage guides, pipes, and power conduits. The lining is generally timber, and as timber can be most easily framed into rectangles, rectangular shaft openings are the rule. The timber reduces the size of the cage floor. For example, if the Idaho Maryland company had put down No. 2 shaft by blasting and mucking, the cage area would have been about thirty per cent of the total shaft area. Besides a low percentage of useful area, an ordinary shaft is subject to fire hazard and to timber maintenance charges. It is also poor for ventilation because the timber ribs cause eddies which greatly reduce the speed of the air currents. A bored shaft does not have these disadvantages. The walls are smooth, circular, and not shattered by blasting, so lining is not required in most

Jan 1, 1936

By Walter R. Hibbard, Cyril Stanley Smith

IN 1929 one of the authors' determined the constitution of copper-silicon-manganese alloys containing over 90 per cent copper. Through a combination of circumstances the presence of the copper-silicon kappa phase was overlooked in both binary and ternary systems. In the binary system the omission has already been rectified.2,3 To establish the limits of this phase in the ternary system, the samples that had been heat-treated at the time of the original research have now been re-examined, using more careful technique. Full details of the compositions used and the temperatures and times of heat-treatment are to be found in the earlier paper .2 The etching reagent now used to distinguish the kappa phase had the following composition: hydrogen peroxide (30 vol.), 20 c.c.; water, 25 c.c.; 20 per cent potassium hydroxide solution, 5 c.c.; ammonium hydroxide (0.90 sp. gr.), 50 c.c. Table I lists the newly observed structures. In virtually every case the constituents are the same as those previously recorded, except where kappa is now shown to be present as a result of the improved etching technique. A few other changes will be noted (No. 138 at 450°C., No. 149 at 550°C., Nos. 153 and 149 at 750°C.). The change from liquid to beta in equilibrium with kappa in No. 139 at 800°C. is based upon newly heat-treated samples. The alloy is very near the solidus at 800°C. and probably there was a slight error in the old heat-treatment temperature. The isothermal phase diagrams shown in Figs. 1 to 6 were reconstructed on the basis of the new studies. The presence of manganese does not greatly change the composition limits of the kappa phase or cause the [K = a + ?] change to occur at a markedly different temperature. There is some uncertainty regarding the range of existence of beta, for alloys were not spaced very closely in composition. The proposed diagrams, however, are in accordance with the available experimental data and with the dictates of the phase rule. Theoretically necessary fields with no experimental points are delineated by dotted lines. The alpha boundaries at all temperatures are shown together in Fig. 7. This includes also some additional points on the alpha boundary at 300° and 350°C., which were obtained as a result of electrical-conductivity measurements. Two series of seven alloys with increasing manganese content but with silicon constant at 1.90 ± 0.03 per cent or 2.42 ± 0.05 per cent were cast in ingots of 3-in, diameter. These were hot-rolled, homogenized and drawn to wire, finished at 0.08-in. diameter with a 61 per cent reduction of area following annealing at 900°C. Conductivity determinations were made before and after annealing for 30 days at 300°C. or 21 days at 350°C. Figs. 8 and 9 show the change of conductivity produced by this annealing, plotted against manganese

Jan 1, 1942

By Nicholas J. Grant, H. C. Chang

EMPHASIS on the importance of grain boundary sliding as a mode of deformation at elevated temperatures has been presented elsewhere.' The extent to which boundary sliding occurs under certain creep conditions has been determined for high purity aluminum2,3 and aluminum alloys.' In general, boundary deformation extends quite far into the adjoining grains, resulting in a rather wide band of deformation along the grain boundaries. This has led some investigators to doubt that grain boundary sliding consists of shearing along the boundary surface; it has been contended instead that boundary sliding is a result of concentrated slip in the neighborhood of the deformed grain boundaries."' The purpose of this note is to present evidence that grain boundary sliding takes place by a bulk shear process. gh purity polycrystalline aluminum, wherever and whenever there is grain boundary sliding, boundary migration and concentrated deformation along both sides of the deformed boundary are associated with it. Therefore, it has been rather difficult to obtain unambiguous evidence of boundary sliding. On the other hand, it would be expected in certain alloys of aluminum, when tested under particular conditions. that the severity of the interfering effects of boundary migration and concentrated deformation along the deformed boundary might be reduced. Current research in this laboratory' shows that a 20 pct Zn-A1 solid solution alloy fractures in an intercrystalline manner during creep at 500°F with a small total elongation of not more than about 14 pct, and that it does so with extremely limited grain boundary migration. Accordingly, this alloy was chosen for the present study. The experimental procedure was similar to that used in previous work and has been presented elsewhere.' Two parallel flat surfaces were milled from a round specimen. The gage portion of the specimen was 1 in. x .09 in. x .17 in. The specimens, which were annealed at 1030°F for 24 hr, showed two to four grains across the width of the test bar. The specimens were subjected to creep at 500°F at stresses of 2000 to 5000 psi. The rupture times were from 10 sec to 3 hr. Appreciable boundary sliding occurred in all the tests. A typical example of boundary sliding is shown in Fig. 1. (The tension axis is vertical in the micrographs.) Sliding has taken place along the boundary between grains A and B unaccompanied by important boundary migration. The sharpness of the offset at the triple point can be clearly seen in grain C. As a result of sliding along the boundary between grains A and B, a new boundary surface between grains A and C was created. The offset at the triple point is about 0.07 mm. This boundary sliding is accompanied by the formation of rather sharp kinking bands and, of course, slip on several slip systems in grain C. This type of deformation has been referred to as fold formation' in previous work with high purity aluminum.

Jan 1, 1957

Jan 1, 1943

By T. S. Fuller

The tensile properties of steels at elevated temperatures have been studied by numerous investigatorsll primarily for the purpose of determining their suitability for structural uses. Tests with this objective have been confined largely to the temperature range of approximately 20" to 500' C., because of the rapidly decreasing tensile strength at the latter temperature. Tests have also been extended to higher temperatures2 for the purpose of determining the most suitable forging range. This temperature range is also of theoretical interest. The phenomenon if increased tensile strength and decreased ductility .in the so-called "blue-heat" range, approximately 200" to 300" C., is well known. It was suggested to the Bureau early in 1926 that a study of the properties of rail steels in this temperature range might prove of interest in relation to the studies of transverse-fissure failures in rails. There were available from another investigation3 several new rails from several different heats made to approximately the same specification requirements, the complete manufacturing histories of which were known. It was decided to determine, at least in the preliminary series of tests, only the ultimate tensile strength, elongation and reduction of area, because of the difficulty, time and cost involved in determining the proportional limit and yield point at elevated temperatures.

Jan 1, 1930

Jan 1, 1900

Jan 1, 1893

Jan 1, 1928

Jan 1, 1916

Jan 1, 1890

Jan 1, 1948