Search Documents

By G. K. Burgess

§ 22. THe results published in Professor Howe's paper10 of our determinations on the Ac3 and Ar3 points for a series of commercial carbon steels " containing manganese in varying proportion, represent the average temperatures found by taking several (4 or 5) heating and cooling curves. The accompanying curves, Figs. 6 and 7, are, for each steel, the first heating and cooling curves as obtained by the inverse-rate method of Osmond, using a cylindrical chronograph sensitive to 0.1 sec. for recording time. Simultaneous observations were also taken by the differential method with a platinum neutral and plotted by Rosenhain's derived differential method and gave substantially the same results, the curves having sensibly the same contours in both cases.12 The observations were taken in vacuo on cylinders 5 by 1 in. in length bored to center with a 1/8-in. hole to receive porcelain insulated thermo-couple, and inclosed in an out- and in-glazed Berlin porcelain tube heated electrically by platinum foil wound on the tube. The vacuum was usually better than 0.1 mm. The heating and cooling of the furnace was automatically controlled by a salt-water rheostat with shaped electrodes, giving a uniform rate of heating and cooling.

Jan 1, 1914

By J. Hunter

LouisiaNa ranks fifth among the oil-producing states. In 1941 the state-wide production was slightly in excess of 118,000,000 bbl. of crude oil and conden-sate—an increase of 15,000,000 bbl. over the total production for the year 1940. During 1941, south Louisiana produced approximately 90,900,000 bbl. of oil, while north Louisiana produced approximately 27,000,000. South Louisiana, therefore, produced about 3¼ times more oil than north Louisiana. During the past year, 574,800,000 M cu. ft. of natural and casinghead gas were produced in Louisiana; thus 1941 gas production exceeded the 1940 production by 104,900,000 M cu. feet. Completion records for the year 1941 show that 1512 wells were completed in or adjoining producing fields. These wells, which were drilled to extend known producing areas or were located within producing areas, are not considered as wildcat wells. Of the total number of field wells drilled, 1152 wells found production; the remaining 360 were junked or dry and abandoned. This means that 76 per cent of the wells drilled were successful. Considering the precarious nature of oil-field development, this percentage of new producing wells is exceedingly satisfactory. Of the total number of field welis com-pleted as producers, approximately 86 wells found new and distinct producing sands. During the past year, 30 new fields were found. Four parishes—namely, Caldwell, Catahoula, Orleans, and Natchitoches— entered the ranks of oil-and-gas-producing parishes in the state during that period. This brings the total number of oil-and-gas-producing parishes in the state up to 48. Thus, 75 per cent of the parishes in Louisiana now contain one or more oil and/or gas fields. Although sufficient data are not available to list the addition reserves found in Louisiana during 1941, it is felt that such reserves undoubtedly exceed twice the total production for that year, or at least 200 million barrels. In reserves, therefore, Louisiana ranks third among the various oil-producing states. South Louisiana Although 16 new fields were found in south Louisiana, the outstanding developments in that part of the state were not limited to new discoveries. In fact, most of the increase in reserve in that area has been most consistently accumulated through extensions of known producing sands and through the finding of new sands in already productive fields, especially at depths below the presently producing sands. Since data concerning most of the new extensions and sands are too extensive for discussion here, the more important developments arc briefly outlined below: Abbeville, Vermilion Parish.—Production extended ½ mile to the west. Anse La Butte, St. Martin Parish.—New oil sand discovered at 9400 ft., thus extending production to east flank. West flank defined by dry holes. Barataria, Jefferson Parish.—New oil sand discovered on east side of field at 7620 ft. New

Jan 1, 1942

By J. Hunter

LouisiaNa ranks fifth among the oil-producing states. In 1941 the state-wide production was slightly in excess of 118,000,000 bbl. of crude oil and conden-sate—an increase of 15,000,000 bbl. over the total production for the year 1940. During 1941, south Louisiana produced approximately 90,900,000 bbl. of oil, while north Louisiana produced approximately 27,000,000. South Louisiana, therefore, produced about 3¼ times more oil than north Louisiana. During the past year, 574,800,000 M cu. ft. of natural and casinghead gas were produced in Louisiana; thus 1941 gas production exceeded the 1940 production by 104,900,000 M cu. feet. Completion records for the year 1941 show that 1512 wells were completed in or adjoining producing fields. These wells, which were drilled to extend known producing areas or were located within producing areas, are not considered as wildcat wells. Of the total number of field wells drilled, 1152 wells found production; the remaining 360 were junked or dry and abandoned. This means that 76 per cent of the wells drilled were successful. Considering the precarious nature of oil-field development, this percentage of new producing wells is exceedingly satisfactory. Of the total number of field welis com-pleted as producers, approximately 86 wells found new and distinct producing sands. During the past year, 30 new fields were found. Four parishes—namely, Caldwell, Catahoula, Orleans, and Natchitoches— entered the ranks of oil-and-gas-producing parishes in the state during that period. This brings the total number of oil-and-gas-producing parishes in the state up to 48. Thus, 75 per cent of the parishes in Louisiana now contain one or more oil and/or gas fields. Although sufficient data are not available to list the addition reserves found in Louisiana during 1941, it is felt that such reserves undoubtedly exceed twice the total production for that year, or at least 200 million barrels. In reserves, therefore, Louisiana ranks third among the various oil-producing states. South Louisiana Although 16 new fields were found in south Louisiana, the outstanding developments in that part of the state were not limited to new discoveries. In fact, most of the increase in reserve in that area has been most consistently accumulated through extensions of known producing sands and through the finding of new sands in already productive fields, especially at depths below the presently producing sands. Since data concerning most of the new extensions and sands are too extensive for discussion here, the more important developments arc briefly outlined below: Abbeville, Vermilion Parish.—Production extended ½ mile to the west. Anse La Butte, St. Martin Parish.—New oil sand discovered at 9400 ft., thus extending production to east flank. West flank defined by dry holes. Barataria, Jefferson Parish.—New oil sand discovered on east side of field at 7620 ft. New

Jan 1, 1942

By J. S. Marsh

Joseph Priestley prepared oxygen on Aug. I, 1774, and noted with great surprise "that a candle burned in this air with a remarkable brilliant flame." On Aug. 2, 1774, some ironmaker possibly began to wonder if this substance could be used to increase his rate of production; at any rate, there is no disputing the fact that the notion of using oxygen for steelmaking in concentrations greater than that available in great abundance—as air—has been in existence for years. Action was delayed by the lack of enough oxygen at a cost within reach of the steelmaker. Within the last several years enough has been available to permit large-scale tests of its use for both combustion, with which this paper is concerned, and for decarburization. The literature is now enormous and easily available; it is sufficient here to cite three items of historic importance in that all are about 25 years old and in that all are remarkably consistent as far as they go, with what is known today.1,2,3 Significance of High-temperature Heat The principal function of the open-hearth furnace is to supply sufficient high-temperature heat to melt the charge and then to increase its temperature to a range suitable for tapping, ordinarily in the neighborhood of 2900°F. That heat is required to make steel is understood by everybody; however, there seems to be some confusion now and then about the significance of high-temperature heat. Transfer of energy—and heat is energy— is always from a point of higher potential to a point of lower potential and, other things being equal, the greater the potential difference, the greater is the rate of transfer of energy. In the open hearth the flame, of course, is the high-potential source. Perhaps the most satisfactory approach is through the notion of theoretical flame temperature, which is the ratio of heat input to the heat content of the combustion products,* the former is composed mainly of heat of combustion of the fuel plus sensible heat of the fuel plus sensible heat of the combustion air. Thus, flame temperature can be increased by increasing the value of the numerator, by decreasing the value of the denominator, or both. The first method is as old as the open-hearth process and, of course, makes use of preheated air; its possibilities have been by no means exhausted. The second method can be put into effect only by changing the composition of the combustion air, since the combustion of a given quantity of fuel produces a definite quantity of product, and since the denominator includes the non-reactive fraction of the air, principally nitrogen. In other words, the denominator consists of the volume of exit gas multiplied by its heat capacity and that volume consists of carbon dioxide and water vapor as reaction

Jan 1, 1949

By J. S. Marsh

Joseph Priestley prepared oxygen on Aug. I, 1774, and noted with great surprise "that a candle burned in this air with a remarkable brilliant flame." On Aug. 2, 1774, some ironmaker possibly began to wonder if this substance could be used to increase his rate of production; at any rate, there is no disputing the fact that the notion of using oxygen for steelmaking in concentrations greater than that available in great abundance—as air—has been in existence for years. Action was delayed by the lack of enough oxygen at a cost within reach of the steelmaker. Within the last several years enough has been available to permit large-scale tests of its use for both combustion, with which this paper is concerned, and for decarburization. The literature is now enormous and easily available; it is sufficient here to cite three items of historic importance in that all are about 25 years old and in that all are remarkably consistent as far as they go, with what is known today.1,2,3 Significance of High-temperature Heat The principal function of the open-hearth furnace is to supply sufficient high-temperature heat to melt the charge and then to increase its temperature to a range suitable for tapping, ordinarily in the neighborhood of 2900°F. That heat is required to make steel is understood by everybody; however, there seems to be some confusion now and then about the significance of high-temperature heat. Transfer of energy—and heat is energy— is always from a point of higher potential to a point of lower potential and, other things being equal, the greater the potential difference, the greater is the rate of transfer of energy. In the open hearth the flame, of course, is the high-potential source. Perhaps the most satisfactory approach is through the notion of theoretical flame temperature, which is the ratio of heat input to the heat content of the combustion products,* the former is composed mainly of heat of combustion of the fuel plus sensible heat of the fuel plus sensible heat of the combustion air. Thus, flame temperature can be increased by increasing the value of the numerator, by decreasing the value of the denominator, or both. The first method is as old as the open-hearth process and, of course, makes use of preheated air; its possibilities have been by no means exhausted. The second method can be put into effect only by changing the composition of the combustion air, since the combustion of a given quantity of fuel produces a definite quantity of product, and since the denominator includes the non-reactive fraction of the air, principally nitrogen. In other words, the denominator consists of the volume of exit gas multiplied by its heat capacity and that volume consists of carbon dioxide and water vapor as reaction

Jan 1, 1949

By T. M. Geffen, F. F. Craig

Laboratory model flow tests have been made to simulate field conditions of partial pressure rnaintenance by dispersed gas drive on rocks having sandstone-type porosity. In this production method there is a significant saturation gradient between injection and production wells. A means of calculating relative permeability characteristics. from partial pressure rnaintenance flow tests has been developed. This method takes into account the saturation gradient. These kg/ko characteristics are identical to those for solution and external gas drives. This method of calculation, which has been proved experimentally, has limitations; however, it is valid for cases likely to be encountered in field prediction of partial pressure maintenance performance. The production performance of a hypothetical reservoir has been calculated for several different injection programs, involving both full and partial pressure maintenance. Results indicate that the maxinum oil recovery by these gas injection programs is obtained by full pressure mainte- nance at the original bubble point. Correspondingly lower oil recoveries are obtained by postponing gas injection and/or by reducing the degree of pressure maintenance. INTRODUCTION Dispersed gas injection is an important method of recovering additional oil beyond that obtainable by pressure depletion alone. The injected gas acts as a source of additional energy to displace oil from the rock formation as well as to retard oil shrinkage in the reservoir. In practice, gas injection is usually started after the reservoir pressure has fallen below the original bubble point. For various reasons sufficient gas is generally not injected to completely maintain the pressure in the reservoir. So, injecting gas at a declining reservoir pressure results in a combined external and solution gas drive. These two oil displacement processes are characterized by different gross saturation distributions in the reservoir. The external gas drive, like all frontal drive processes, inherently results in an oil saturation which increases from the injection wells to the producing wells. In the solution gas drive there is essentially a uniform oil saturation throughout the reservoir, provided the field is being depleted uniformly. It has been customary to predict oil recovery performance under partial pressure maintenance by a method which does not take into account the saturation gradient1. It has been shown2 that neglecting the presence of a saturation gradient can cause considerable error. It is the purpose of this paper to develop and present an improved method of predicting partial pressure maintenance performance of reservoirs including, where necessary. the effects of well arrangement. From the laboratory standpoint, this problem involves the measurement of the basic flow behavior (relative permeability characteristics) under partial pressure maintenance conditions. Recent research- as shown that for rocks having sandstone-type porosity, the relative permeability characteristics are identical for solution gas drive and complete pressure maintenance external gas drives. Since both solution and external drives have the same basic flow behavior, it was speculated that partial pressure maintenance, being a combination of the two, would also

Jan 1, 1957

By J. S. Marsh

JOSEPH PRIESTLEY prepared oxygen on Aug. 1, 1774, and noted with great surprise "that a candle burned in this air with a remarkable brilliant flame." On Aug. 2, 1774, some ironmaker possibly began to wonder if this substance could be used to increase his rate of production; at any rate, there is no disputing the fact that the notion of using oxygen for steelmaking in concentrations greater than that available in great abundance-as air-has been in existence for years. Action was delayed by the lack of enough oxygen at a cost within reach of the steelmaker. Within the last several years enough has been available to permit large-scale tests of its use for both combustion, with which this paper is concerned, and for decarburization. The literature is now enormous and easily available; it is sufficient here to cite three items of historic- importance in that all are about 25 years old and in that all are remarkably consistent as far as they go, with what is known today.1,2,3 SIGNIFICANCE OF HIGH-TEMPERATURE HEAT The principal 'function of the open-hearth furnace is to supply sufficient, high-temperature heat to melt the charge and then to increase its temperature to a range suitable for tapping, ordinarily in the neighborhood of 2900°F. That heat is required to make steel everybody; however, there seems to be some confusion now and then about the significance of high-temperature heat. Transfer of energy-and heat is energy is always from a point of higher potential to a point of lower potential and, other things being equal, the greater the potential difference, the greater is the rate of transfer of energy. In the open hearth the flame, of course, is the high-potential source. Perhaps the most satisfactory approach is through the notion of theoretical flame temperature; which is the ratio of heat input to the heat content of the combustion products,* the former is composed mainly of heat of combustion of the fuel plus sensible heat of the fuel plus sensible heat of the combustion air. Thus, flame temperature can be increased by increasing the value of the numerator, by decreasing the value of the denominator, or both. The first method is as old as the open-hearth process and, of course, makes use of preheated air; its possibilities have been by no means exhausted. The second method can be put into effect only by changing the composition of the combustion air, since the combustion of a given quantity of fuel produces a definite quantity of product, and since the denominator includes the non-reactive fraction of the air, principally nitrogen. In other words, the denominator consists of the volume of exit gas multiplied by its heat capacity and that volume consists of carbon l is understood by dioxide and water vapor as reaction

Jan 1, 1948

By Nelson Severinghaus

Mineral fillers have been defined as inert materials that are included in a composition for some useful purpose. Because this definition and the scope of this review are not specific-indeed, exceptions abound-accurate total statistics are unavailable. One source estimates the total production in the United States in 1979 at 11.3 Mt (12.5 million st) valued at $534 million, averaging $49.19 per ton. Included are a broad group of minerals-asbestos, barite, bentonite, ground limestone and dolomite, clays, diatomite, feldspar, micas, silica, talc. Additional references will be made to synthetic mineral-derived fillers such as aluminum hydrate, precipitated calcium carbonate, and pyrogenic and precipitated silicas and silicates. A section on related uses at the end of this chapter covers absorbents and filters. Mineral fillers can be included in compounds to accomplish a variety of final results. Hardness, brittleness, impact strength, compressive strength, softening point, fire resistance, surface texture, electrical conductivity, and a host of other physical characteristics may be modified by the inclusion of fillers. These effects are the result of properties of the fillers, including chemical activity, hardness, particle size, shape and distribution, surface structure, color, density, and refractive index. To facilitate an overview of the mineral filler industry, this chapter will review the general usage of fillers, the inherent characteristics that intensify their utilization, and similarly their manufactured characteristics. Major using industries will then be examined in detail. Specific information on deposits and processing for industrial minerals will be found in the appropriate commodity chapter. All of these same minerals have additional significant uses based on their chemical composition or other characteristics. References will be found in other use chapters and summarized in commodity chapters. The chart in Table 1, updated from the 4th edition of Industrial Minerals and Rocks, illustrates the major mineral fillers (both natural and manufactured) and their more important end uses. Use of Mineral Fillers Archaeologists have found that more than 5000 years ago, bitumen used for mortar and waterproofing contained mineral contaminants that acted as fillers. Since that time man has added mineral products to compounds to improve certain characteristics. Perhaps the most common objective of filler usage is reduction of cost of the end product. Certainly the inclusion of a filler that costs 2¢ per 0.45 kg (lb) will reduce the cost of a plastic product whose resin costs 50¢ per 0.45 kg (lb). But the decision to use a specific filler is not that simple. It may "soak up" binder, making a compound more viscous and perhaps preventing its flow into a mold as an injection molding compound, but similarly will give good anti-sag characteristics to putty, caulking compound, or undercoating. Fillers may be incorporated to modify: 1) Cost 2) Physical characteristics 3) Flow characteristics 4) Fire resistance 5) Density 6) Heat conductivity 7) Color or brightness and opacity 8) Hardness, brittleness, impact strength 9) Deformity, viscosity, softening point 10) Processing problems 11) Electrical conductivity 12) Surface texture 13) Thermal expansion characteristics 14) Abrasion resistance

Jan 1, 1983

By James J. Scott

INTRODUCTION This paper presents the basic principles which must be followed to create a truly inherently safe mining system. The need to relate the support mechanism to be employed to the ground reaction curve and basic rock mechanics principles will be pointed out. The support system must function in concert with the deformations that are inherent in the selected mining system. Following the support selection, the mechanics for installing support must be developed. This is best done through a cooperative effort between mine engineers, mine operators, safety personnel, equipment sup- pliers, and government inspectors both state and federal. Accident statistics, near miss statistics, review of equipment used by others, geologic features, etc. will necessarily have to be studied. The goal of equipment development and selection should be to develop inherent safety by removing the miner from the hazard area or by providing absolute protection for the miner if he must work in close proximity to the potential fall of ground. The role of good productivity in reducing the numbers of men exposed to hazards is emphasized as a good safety measure ROCK MECHANICS PRINCIPLES A thorough understanding of the ground reaction curve surrounding openings to be created is essential in the

Jan 1, 1982

By Chester T. Sims

RECENTLY, a new type of superalloy material called TD Nickel* has been marketed.' It is a sim- ple, two-phased alloy, consisting of thoria particles dispersed in nickel of rather high purity (Ni-2 pct Thoz). Its mechanical properties appear relatively superior to previous experimental material attempting to use the oxide nonmetallic dispersion concept (except SAP), and superior to conventional nickel-base alloys at high homologous temperatures. This is derived from an interesting method of creating the dispersion, arising during chemical processing of the nickel and thorium salts in solution while reducing the nickel to metal. An evaluation of the thoria phase was conducted at this laboratory. Material and Procedure. TD Nickel was made available, consisting of several inches of 0.470-in. rod, extruded at a ratio of 64: 1, straightened, and centerless ground. Property determinations on this rod by the supplier at 1800°F showed an ultimate tensile strength of 11,400 psi, yield strength of 9600 psi, and 6 pct elongation. Specimens were removed from the rod for as-extruded metallography, and two 1/2-in. lengths supported on high-purity Al2O9 bricks were placed in a laboratory muffle furnace for exposure at 2000° F. The furnace door was left cracked to allow a slight amount of circulation. One specimen was removed at 200 hr for examination; the other was left for 2000 hr. Metallography. The micro structures obtained for the three conditions of exposure are shown in Fig. 1. Elongation of the grain structure in the extrusion direction is readily evident. The grains appear to be up to 0.001 in. (0.003 cm) long, with a length/width ratio of about 10: 1. Allowing for modest local in-homogeneities in structure, no significant change in thoria particle size or nickel alloy grain size occurred during the 2000°F exposure. However, etching depth varies slightly from one specimen to another, changing the number of particles visible. The thoria dispersion appears to be in the order of 0.01 (min) to 0.5 (max) p diam. The minimum diameter is difficult to estimate at X10,000, and may be less. Interparticle spacing appears to be about 0.1 p. Etching effects can be seen, depending upon grain orientation. A cubic etch-pit pattern appears in certain grains, apparently when etching is started by an anodic particle of thoria, Fig. l(c). The cubic pattern appears related to crystallographic orientation, and is prominent when the [ l00 ] direction is perpendicular to the plane of polish. The grains which present a ridged appearance in the photograph appear to be oriented with the [110} direction perpendicular to the plane of polish. Analysis. The thoria particle size was measured by a line intercept method perpendicular to the extrusion direction. Only particle sizes measuring 0.001 in. at X10,000 or larger could be extimated. Within limits of experimental error, particle size distribution appears to be unaffected by exposure, Fig. 2. To check structural stability further, a grain-growth evaluation was made. The number of grain-boundary intersections was counted at X500 on each of several traces normal to the extrusion direction for each condition. It can be seen from Table I that grain diameter appears unchanged by the 2000°F exposure. The slightly finer grain diameter after 200 hr may be attributed to variations in grain size from area to area in the original extrusion. From the present rather limited study of Ni-2 Th on, it appears that: 1) for time-temperature exposure up to 2000 hr at 2000°F (Larsen-Miller parameter = 57, homologous temperature = 0.8) thoria particles of the size studied are highly thermally stable; they do not significantly react, agglomerate, or diffuse; and

Jan 1, 1963

By G. R. Love, M. L. Picklesirner

THE use of color adds a new beauty, power, and versatility to metallography. This has been amply demonstrated in a number of public exhibits and on the walls of corporate, government, and university metallographic laboratories around the world. Indeed, in a number of cases, the color not only is of esthetic value but is scientifically essential to the competent examination of particular samples and systems. Optical strain analysis,' determination of true grain size in U-A1 alloys: phase identification in Nb-base alloys,3 analysis of transformation rates in heat-treated Nb-Zr alloys,4 measurement of solidification segregation in cast Nb-Zr alloys,' study of the intermediate phases in Nb/Sn diffusion couples,6 investigation of the oxidation kinetics at various surface orientations in single crystals,7'8 and a number of other research efforts9'10 would have been vastly more difficult without the extra clarity and distinction introduced by color—either the colors resulting from particular polarized light techniques or the interference colors obtained by oxidation. It is unfortunate that the beauty of colored micro-structures cannot be shared more widely, but the economics of publishing a technical magazine apparently prohibits color plates except under extraordinary circumstances. It is doubly unfortunate that no convenient, general method exists for communicating the information available in colored microstructures to the scientific community. True, in some instances the color changes observed are dramatic enough that direct black and white photography is adequate. In photoelastic stress analysis, several orders of interference fringes may be produced and it is frequently desirable to suppress the color effects (use monochromatic light) to simplify interpretation. On the other hand, relatively minute color variations may be readily detectable by eye, be of considerable assistance in interpreting a structure, and yet be enormously difficult to reduce to an unambiguous black and white print. In order to illustrate a possible compromise or solution to the above problems, we wish to show three black and white photographs of the same region of an Nb/Sn diffusion couple whose interpretation depends heavily upon use of color techniques. These micro-structures were obtained from a section through a rod consisting of commercial-purity niobium tubing filled with 99.995 pct Sn (melt-filled in 10"6 Torr vacuum). The composite rod, measuring 500 mm long, was bent into a hairpin shape and inserted into water-cooled copper grips in a vacuum high-temperature furnace. The rod was outgassed for 2 hr at a furnace temperature of 800°C and was further heated by self-resistance using a 2.2-kva ac power supply. The rod was raised to 1910°C over a 4+-hr period, held for 15 min, slow-cooled to 1500°C over a -hr period, and free-cooled to room temperature (all temperatures were measured with W5Re/W26Re thermocouple). Throughout the heat treatment the ambient pressure was kept below 8 x lo-' Torr. Metallographic preparation of the sample was completely conventional except that it was necessary to extend the grinding steps to remove damage in the brittle NbsSn phase introduced by sectioning. No satisfactory chemical or electrochemical etch has been found for these diffusion couples; of those which have been tried, any that attack the niobium-rich phases at all attack the tin-rich phases disastrously. However, the final polishing steps did produce a slight relief effect and this, coupled with anodizing, yielded excellent clarity in the microstructures for direct observation. The anodizing voltage was chosen to give maximum change in color per unit change in composition. In this case, indeed normally, this maximum sensitivity occurred in the blue-to-red color range. The pure niobium tube wall anodized to a relatively bright blue

Jan 1, 1967

By W. P. Rawles

In the foreword by C. K. Leith, Chairman of The Mineral Inquiry, it is pointed out that the ordinary mineral production tables do not show the commercial control, and that some knowledge of the situation is desirable as a background for the consideration of problems involving mineral raw materials. The report consists principally of tables, accompanied by a brief text, giving the production and an analysis of the control, according to nationality, of 18 minerals: aluminum, chromite, copper, iron and steel, lead, manganese ore, mercury, molybdenum, nickel, nitrates, petroleum, potash, silver, sulfur, tin, tungsten, vanadium, and zinc. For the most part, the production figures for 1929 and the latest figures for reserves have been used. When feasible, the control has been shown at the various stages of production; mining, smelting and refining. American capital was dominant in the production of 10 mineral commodities, including six of the most important; British capital, in four instances; while Spanish, German, Chilean or Chinese interests cach led in the control of one. British, French, German, and Dutch capital occupied second place in the control of most of the important minerals. Between two-thirds and three-fourths of the world's mincral production is controlled by British and American capital.

Jan 1, 1934

By Roy McLellan

THE slags derived from the smelting of lead and copper ores are composed essentially of silicates. The problems arising from the smelting of these ores consequently involve the study of silicate fusions. In the absence of specific knowledge concerning the compounds occurring in slags, it has been the practice of metallurgists to treat them in terms of their total chemical composition. Slags have been classified as monosilicates, bisilicates, sesquisilicates, and subsilicates according to the relative amounts of oxygen in the acid and basic radicles of the hypothetical salt produced. While this has been a useful guide to metallurgists in computing the furnace charges, it falls far short of a basis for the scientific investigation of slags. In order to understand the nature of a slag as a whole it is necessary to learn the physical and chemical properties of the mineral compounds which go to make up that slag. The efficiency with which an ore is smelted in a furnace depends primarily on the physical properties of the compounds formed during the operation. When the melting points and fields of stability of each of the mineral compounds in slags have been established, it will be possible to determine the properties of any given slag by examining the nature and amounts of its mineral constituents.

Jan 1, 1930

By W. R. Davison, C. A. Brown, J. P. Carstens

INTRODUCTION The phenomenon of heat-weakening of rock with 10.6 micron radiation from a continuous-wave C02 gas laser has been investigated in detail at the Massachusetts Institute of Technology for over 5 years. The programs at MIT have explored the basic nature of the heat-weakening phenomena and rock fracture caused by heating (e.g., Refs. 1 and 2), and have resulted in quantitative estimates of the relationship between the amount and parer level of heating and the resulting decrease in the modulus of rupture of a rock beam in a three-point bend test (Ref. 3). Results of the tests reported in Ref. 3 indicate a greater than 90% reduction in the modulus of rupture for granite beams heat-weakened by a laser. These results prompted the U. S. Department of Transportation to seek an assessment of the expected feasibility of employing the heat- weakening concept in a full-scale tunnel boring operation. Present- day continuous rock-tunneling machines have demonstrated tunneling time and cost savings over drill-and-blast methods, when used in rock types that are easily broken by the cutters. However, cutter bits have not yet been developed which can easily penetrate very hard rock

Jan 1, 1971

By George B. Clark

THE geological data emphasized so successfully in prospecting for new deposits, that is, structural controls, strength of solutions, and type of mineralization, are basically those required for successful exploitation. In the mining of newly discovered deposits the most economical methods should be employed as early as possible to keep the overall cost per unit produced at a minimum and to permit maximum extraction of valuable minerals. A crucial question is: How can geological data be translated into useful quantitative results which will aid in achieving this end? H. E. McKinistry1 has suggested that a solution may be reached in one of two ways: 1-the usual approach, use of judgment based on experience; or 2-mathematical calculations and tests on models, both subject to certain limitations. He also suggests that in addition to better use of geology more case data and theoretical data are needed on which to base sound judgment. Further research, therefore, is necessary. Perhaps in this field the emphasis should be on more specialization in mining methods and ground movement by men with thorough training in physics, engineering, geology, and underground mining. These specialists would be equipped to point out the most economical and scientific methods of exploitation.

Jan 8, 1954

By C. R. Watts

The feasibility of producing composites containing nickel or molybdenum fibers in a beryllium matrix was inrestigated. The composties studied were jabricaled by powder mallurgical techniques. The 1-mil-diarr nickel fibers reacled completely below 900°C, converling the fibers .from nickel to Ni5Be2,. As the /LO/-pressing temperalure as raised above 1110oC, tlie nickel diffused outward from the beryllide fibers. The solid solubility of nickel in beryllium was clboul 20 wt pet at the 1100°C pressing temperature a1 the zone-fiber interface. The 1.5-mil-diam molybdenum fibers slzolred no evidence of reaction and little evidence of diffitsion after pressing at 900°C. Between 1000° and 1050°C pressing conditions, the fibers began lo react , producing 1ayers of MoBe2 and MoBe12, respectively surrounding the molybdenurn core. The struture remained the same at 1100°C with no evidenre of solid solubility of the molybdenum in the berylium or vice versa. In recent years a considerable amount of attention has been devoted to the determination of methods for improving the mechanical properties of materials through the use of fiber or whisker reinforcement. Previous work with metal matrix composites indicates that the study of the chemical compatibility of the fiber and matrix is an area requiring greater understanding. The metal-metal or ceramic-metal interface is frequently subject to chemical reactions that may result in the formation of hard brittle intermetal-lic compounds and/or low melting point eutectic compositions. The reaction products may reduce both the low-temperature and elevated-temperature strength of the composite by weakening the fiber-matrix bond, producing premature failure at the interface. It is well-known that most metal-metal systems and many metal-ceramic systems of interest for structural composites are thermodynamically unstable,'-" particularly at elevated temperatures. If, however, the rate of reaction under the conditions of fabrication is sufficiently low. composites can be fabricated that can be used efficiently for indefinite periods at low temperatures and for short periods at elevated temperatures. This paper presents the results of a series of tests to determine the compatibility of nickel and molybdenum fibers with beryllium at various hot-pressing temperatures. Nickel was selected as a candidate fiber material primarily because the relatively ductile fibers might be useful as crack arresters in applications such as ballistic impact where crack growth can result in catastrophic failure. The high density and the reactivity of nickel were primary factors detracting from its selection as a possible reinforcement. Molybdenum with a modulus of elasticity of 52 Xlo6 psi is one of the few metallic materials having a modulus higher than beryllium (42 X lo6). Its high modulus, coupled with its refractory characteristics, made molybdenum an attractive candidate for a relatively stable fiber reinforcement for beryllium. Its density, being higher than that of nickel and over five times that of beryllium: detracted from its other characteristics. EXPERIMENTAL PROCEDURE The specimens were prepared from beryllium powder with a dispersed phase of fibers by powder metallurgical techniques. P-20 grade powder, Table I, from Berylco was used as the matrix material. Short lengths of 0.001-in.-nominal-diam nickel fibers supplied by the Sigmund Cohn Corp. and 0.0015-in.-nominal-diam molvbdenum fibers obtained from the General Electric Co. were used as the dispersed phase. The composite constituents were combined under an argon atmosphere by mechanically mixing the powders and fibers. The compositions used were nominally 1 vol pct fibers. After mixing. the composites were hot-pressed into a-in.-diam pellets under an argon atmosphere at 900°, 1000". 1050". and 1100°C at a pressure of 6000 psi with no hold time at these temperatures so that a comparison could be made between the resultant microstructure and hot-pressing temperature. The billet was heated at a rate on the order of 30°C per min to the desired temperature and then cooled at a somewhat slower rate. The microstructure obtained should be considered as characteristic of the integrated time-temperature history of the sample, as well as the maximum temperature attained. Upon removal from the hot-pressing dies. the specimens were cut. mounted. and polished by standard procedures. No etchant was used in specimen preparation. Photomicrographs, electron microprobe scans, and electron back-scatter pictures were made. X-ray dif-fractometer patterns were made of several of the specimens. but only the lines for beryllium could be resolved. Specimens for optical and electron microprobe examination were selected partially for the roundness of the cross section. A round cross section was taken to indicate that the body of the fiber was approximately normal to the surface and that therefore effects due to fiber material immediately below the surface could be neglected. RESULTS AND DISCUSSION The microprobe scans indicated that nickel reacted as low as 900°C, converting the entire fiber cross section to NisBe21. Fig. l(a). There was no evidence of further reaction from the optical or the back-scatter pictures, Figs. 2(n) and 3(a).

Jan 1, 1970

By V. M. Lovell

The recovery of apatite from the phoscorite ores occurring in the Transvaal, Republic of South Africa, involves a flotation process that is particularly difficult to characterize from a fundamental point of view. However, the reagents used, (tall oil fatty acid, nonylphenyltetraglycol ether, sodium silicate, and sodium hydroxide) can successfully bring about a separation of apatite from dolomitic calcite, which is the most troublesome gangue component. Recently, it has been demonstrated with some flotation feeds that the addition of certain polysaccharides can improve the flotation significantly. It has been shown that the metallurgy obtained is closely linked to the nature of the froth, and this, in turn, is influenced, often dramatically, by the presence or absence of certain of the reagents. The character of the froth depends less on the inherent frothing ability of these reagents than on the presence or absence of fine mineral particles in the froth, and on their surface characteristics and state of aggregation. The polyglycol ether and the polysaccharides have been shown to affect these properties, and it is suggested that a major function of these reagents is to modulate the properties of the fine particles in the pulp, thereby changing the character of the froth and giving rise to improved results.

Jan 1, 1976

By J. A. Cahill, A. D. Kirshenbaum

Using an alumina or zirconia crucible with an alumina sinker or a molybdenum sinker coated with zirconium dioxide, the density of liquid iron was determined by the immersed-sinker method over the temperature range of 1800" to 2500°K. The density, with respect to temperature, is ex-Dressed by the equation Dg/cm = 8.523 - 8.358 X 10 T'K The molar Volumes and thermal coefficients of expansion were calculated. Iron, upon me1ting, was found to expand 3.5 pct. A basic knowledge of the physical properties of materials at high temperatures is becoming increasingly important. A check of the literature shows, that in spite of the importance of iron, very few measurements have been made of its physical properties in the liquid state. Density measurements have been made by Benedicks and his collaborators1g using the method of balanced columns, by Desch and smith4 using the immersed sinker method with an alumina sinker, by Lucas using the maximum bubble method5 and by Stott and endall' who used an alumina pyknometer. In the method of balanced columns, the difference in level of molten iron in two arms of a U-tube, together with the corresponding difference of pressure had to be measured. The formation of gas bubbles in one or both arms was a great source of error. These values are very erratic. They vary from 6.83 to 7.45 g per cm3 at the melting point (1805"~) and from 6.45 to 7.15 g per cm3 at 1890°K. Stott and Rendall determined the density at 1837"K, with a reproducibility of *0.2 pct. They used an alumina pyknometer fired to 1973°K. The vessel was filled in a vacuum furnace by immersion in the liquid metal. When thermal equilibrium was attained, the pyknometer was withdrawn, cooled, the ingot removed and then weighed. The chief disadvantage of the method was the difficulty of inserting the pyknometer without cracking it. The authors have been able to determine the density of liquid iron from its melting point up to 2500°K, by using the immersed-sinker method, with A1203 or ZrOz crucibles and A1203 or molybdenum sinkers coated with Zr02, Fig. 1. EXPERIMENTAL Apparatus. In these studies the source of heat was the carbon tube resistance furnace with an argon atmosphere described previously.7 Experimental runs were made using either Ala3 or ZrOz crucibles. The sinkers used were 1) pure A1a3 and 2) molybdenum coated with ZrOz. The crucible, 2 1/8 in. in diam and 3 in. high, was centered in the furnace on an Ala3 of Zr02 pedestal. The sinker, 1/2 in. in diam and 1 1/2 in. long, together with a counter weight, was suspended from an analytical balance into the melt by a molybdenum wire. Procedure. The procedure, as described previously,' consisted in measuring the weight loss of the sinker in the liquid iron while determining simultaneously the liquid iron temperature by means

Jan 1, 1962

By J. L. Brimhall, R. A. Huggins, M. J. Klein

IN a recent paper1 it was shown that small additions of magnesium, copper, and oxygen decrease the stacking fault probability in plastically deformed silver. Correlation of :X-ray data with measurements of the twinning frequency and metallographic observation of slip lines indicated that this effect may be due to an increase in the relative stacking fault energy. It is the purpose of the present note to report experiments on these alloys of known stacking fault probability that relate to the stacking fault contribution to electron scattering in silver. There has been a considerable amount of disagreement in the literature concerning the contribution of dislocations to electrical resistivity in metals. Calculations relating to the scattering of conduction electrons by the dislocation core, its strain fields, and related effects have been made by several authors.2-5 In addition, experimental work on Cu,3,6-10 Ni,11 and Ni-Co alloys1:! has shown that dislocations in those materials exert an anomalously large effect on resistivity, this effect being related to the presence of extended dislocations. The problem of the scattering due to the stacking fault region between partial dislocations has been treated theoretically using several different procedures.13-'0 The results of these calculations show a wide range of predicted values, from rather large to completely negligible, due to the models and the approximations involved. Almost all of this work has been applied to the specific problem of scattering in copper. The more complete theoretical treatments depend rather critically. on the shape of the Fermi surfaces and the effective mass parameters. The scattering from stacking faults might therefore be expected to vary significantly from one metal to another. Unfortunately, sufficiently accurate information is not available .which would allow one to have any confidence in a theoretical prediction of the scattering in the case of silver. Resistivity measurements were made on small wire specimens of vacuum melted high purity silver and several dilute alloys. These measurements were made at approximately 20°C, with great care being given to temperature measurement and corrections. At such temperatures phonon scattering is significantly greater than imperfection scattering. However, the experimental technique was such that measurements on similarly treated samples were reproducible to better than 2.4 X 10-9 ohm-cm, which was satisfactory for this work. Values of the stacking fault probability and the increase in resistivity after severe plastic deformation are given in Table I. The increases in resistivity resulting from plastic deformation agree quite well with previous work on silver.14,21-26 In addition, it has been previously found that interetitials and vacancies in silver anneal out well below room temperature, so that the residual imperfection scattering in these experiments could be expected to be primarily associated with dislocations;. It is seen from the data in Table I that large changes in stacking fault probability are accompanied by differences in resistivity due to imperfection scattering of only a few percent. If the scattering of conduction electrons by extended dislocations is primarily due to the area of the stacking fault region independent of the stacking fault energy, and not the core and strain fields associated with partial dislocations, the resistivity increase should be proportional to the product of the dislocation density and the stacking fault width, as is the stacking fault probability. Therefore, the imperfection scattering caused by plastic deformation of the alloys should be considerably smaller than that found in the pure silver. Since this was not observed, these results sugegest the possibility that stacking faults do not themselves contribute appreciably to the electrical resistivity of silver deformed at room temperature. An alternative explanation of these observations is that the scattering by the stacking fault is roughly proportional to the stacking fault energy, rather than being determined by the total area of such faults. Sufficient evidence is not yet available to separate these two possibilities. This work was supported by the Office of Naval Research.

Jan 1, 1962

By AIME AIME

FEW mining engineers-noted as the profession is for migratory predilections.--can point to as varied a record as Scott Turner, director of the U. S. Bureau of Mines and newly elected vice-president of the Institute. His record as printed shows that from the time of his graduation from the Michigan College of Mines in 1904 until he went to the Bureau in 1925, he worked for 21 different companies. Geographically the record is no less imposing, although one reason for this is the fact that he was field engineer for several exploration companies. Virtually every important mining state in the Union is represented in addition to Canada, Alaska, Panama, and several countries each in South America and Europe. In addition to all of the common metals he has mined tin and coal. He opened and operated for five years a group of coal mines in 73" 13' S. Lat., on the Island of Spitzbergen. This was 825 miles north of the Arctic Circle on No Man's Land, where Mr. Turner claimed and maintained pos- session under the American flag of an area of 600 square miles. Incidentally, he was a survivor of the ill-fated Lusitania, sunk by a submarine in May, 1915.

Jan 1, 1930