Search Documents

By C. R. Sandberg, L. S. Gournay, R. F. Sippel

The effect of fluid-flow rate and fluid viscosity on oil-water relative permeability determinations was studied using the "dynamic flow technique." In this work relative per-nleability curves were obtained for homogeneous small core .samples from several sandstorle outcrop form-utions. Radio-tracers were used for the determination of fluid saturation and for the detection of saturation gradients. Cobalt-60 in the form of cobaltous chloride was used as a water-phase tracer in some of the experiments. Iodine-131 in the form of iodobenzene and Mercury-20-3 in the form of mercury diphenyl were used as oil-phase tracers in other experiments. Flow rates for each phase were varied within a range of 2.5 to 140.6 ml/hr. Oil-phase vis-cosities under flowing condition,> were varied from 0.398 to 1.683 cp. The relative permbilities ob-tained were found to he solely a function of saturation and independent of flow rare, provided there was no .Saturation gradient induced in the core sample by "boundary effect." Even though equilibrium with re-sped to flowing conditions was obtained at the lower flow rates, where a saturation gradient exists, this equilibrium is of a "contingent"-type rather than the "steady-state" equi-librium implicit in the relative per-meability concept. The only effect of increasing the oil or non-wetting phase viscosity was to decrease the flow rate required for the elimina-tion of the boundary effect. Fairly good agreement between experimentally determined and calculated values of the boundary effect was obtained when the non-wet-ring oil phase was the only Flowing phase. INTRODUCTION In the characterization of reservoir rock, as well as in the solution of reservoir production problems, it is most desirable to have reliablc rela-tive permeability measurements for the rock and fluids of interest. Many techniques have been developed for the laboratory determination of the relative permeability of both large and small core samples. In varying degree, difficulties attend the use of all of the methods. Each of the methods requires the metered flow of fluids of known viscosity through the core sample under conditions wherein the pressure drop in the individual flowing phases can be measured or closely approximated. Since the relative permeability is a function of the saturation and distribution of the flowing fluids, some means of obtaining such information is also required. The laboratory determination of the relative permeability of a sample should give the same relative permeability saturation relationship that would exist if the sample were in place in the oil reservoir. The attainment of this objective is complicated by the fact that the use of small core samples for laboratory measurements is usually necessary. As a result, errors in measuring the relative permeability arise from boundary effects at either the fluid input or output ends of the sample; no significant boundary effect is anticipated at the sides of the sample normal to direction of fluid flow. At the input end of the sample a boundary effect exists if the flow fluids are not com- mingled as they would be in the reservoir. At the output end of the sample a boundary effect exists as a result of discontinuity of the capillary properties of the system. Here the flowing fluids leave the small flow channels and enter a collecting system having much enlarged flow channels. Thus, there is a tendency for the wetting phase to be retained by the core sample because of the attraction of the core sample for the wetting fluid. No reference is made to these boundary effects in either Darcy's equation or in the relative permeability concept. As a consequence the saturation effect peculiar to the input end of the core sample may cause an error in the effective permeability measurement, since some portion of the core sample must be utilized for commingling of the flow fluids. At the output portion of the core sample a saturation gradient or a saturation change along the axis of flow results. Since relative permeability is a function of fluid saturation, this saturation gradient may cause a variable permeability measurement, especially since extent and character of the saturation gradient can vary with fluid-flow rate. The most convenient method of minimizing the boundary effect, especially at the output end of the sample, is to flow the fluids of interest through the core sample at such high rates that the capillary forces arc insignificant as compared to the viscous forces involved in the fluid flow. Since recent work of a preliminary nature has indicated that fluid dispersion in the porous medium increases with the flow rate, the high flow minimizes the boundary effect at the input end of the core sample by enhancing the mixing of the fluids.

By Charles White Merrill

Mankind's progress is measured in minerals. Man's emergence from prehistory is marked by passage through a Stone Age and a Bronze Age and into the present era, sometimes called the Iron Age or the Age of Metals. With the evolution of civilization and the development of a modem industrial economy, minerals become more and more important. Structures, roads, and machines are built largely of minerals; the energy to heat the structures and to drive the machines is mostly mineral; agricultural fertility is maintained by mineral fertilizers and water; and military strength is provided by fortresses, armaments, and munitions, largely of mineral origin. Thus in the material world, in the productivity of the economy, access to minerals has paramount importance. Every evidence indicates increasing dependence on minerals in the modem economy, particularly on the mineral fuels as energy sources to provide the power base for advancing industrialization. Both the total and the per capita consumption of almost every mineral is increasing in the industrialized nations. Moreover, nations with predominantly agrarian economies call themselves underdeveloped and universally strive to industrialize. Most mineral consumption trends in the more advanced economies have been greatly exceeding population growth-which itself has been advancing at an accelerating rate-and sometimes have surpassed the growth in real income. Some minerals have only recently been adopted or grown to importance in use. Titanium metal did not appear as a commercial product until 1948, and even coal seriously displaced wood as a source of heat less than two centuries ago. On the other hand, minerals have always played an important role in construction. The prehistoric megaliths that form the dolmens of Salisbury Plain are stone; the pyramids are andesite faced with limestone; and many other ancient structures are built of mineral materials. In modem times the whole course of architecture has been redirected by new building materials, mostly mineral. Most conspicuous is the sky-

Jan 1, 1964

By Augustus Locke

San Francisco Meeting, October, 1911.) Two Opposed Interpretations of the Tonopah Structure.-The important geological publications concerning the Tonopah mining-district are those of Spurr 1 and of Burgess.2 In these publications are presented fundamental differences of interpretation, which are the more interesting because both authorities have had ample opportunity for observation, and because both are geologists of proved ability. I was vastly puzzled to know which had the better of it, and in order that I might reach a conclusion in my own mind, I recently spent some time in the district going over the physical evidence. Surprising as it may seem, this evidence looks agreeably conclusive. A review of it will, I believe, be of interest to those who are familiar with the previous publications. The general geological features of Tonopah are shown in Fig. 1, and the differences of interpretation referred to are outlined in the accompanying notes. Briefly, Burgess regards the various rocks as flows, lying in the order of their deposition. Spurr regards them in part as flows, and in part as flat-lying intrusives. The disagreement, then, concerns the rocks regarded on the one hand as intrusives, and, on the other hand, as flows. These rocks are chiefly the so-called calcitic andesite, the upper rhyolite, and the lower rhyolite. Economic Importance of the Question of Interpretation.-The economic importance of the question of interpretation is, of course, limited to its bearing on the probable distribution of 1 Geology of the Tonopah Mining District, Nevada, Professional Paper No. 42, U. S. Geological Survey (1905). Report on the Geology of the Property of the Montana-Tonopah Mining Co. (1910). An abstract of this report is given in the Mining and Scientific Press, vol. cii., No. 16,p. 560 (Apr. 22, 1911). 2 The Geology of the Producing Part of the Tonopah Mining District, Economic Geology, vol. iv., No. 8, pp. 681 to 712 (Dec., 1909).

Feb 1, 1912

By Franklin R. Carpenter, W. P. Headden

TWO notes have already appeared in the Transactions concerning the columbite or tantalite of the Black Hills tin-mines. In vol. xiii., page 232, Prof. Schaeffer speaks of the mineral as tantalite, and concludes by saying that its separation from the tinstone "is a matter which will, I believe, prove puzzling to the wisest metallurgist." He also observes that he is unable to find by analysis in his specimens the least trace of columbic acid. Prof. W. P. Blake, in the same volume, at page 696, says: " Even if it [tantalite or columbite] were present to a considerable amount, it would not injure the tin in smelting. It does not alloy with tin, but carries a small percentage of tin, which would probably be liberated in smelting." He calls the mineral columbite from the fact that a great number of specificgravity tests invariably indicated that it should be so classed. We have made chemical tests as well as specific-gravity tests upon many samples from many different parts of the Hills. Our analyses have always shown the presence of columbic acid, and the specificgravity tests have always indicated columbite, as we have elsewhere shown.* As Prof. Blake has already observed, it is not found in such close association with the tin as to prevent separation by a rough handsorting, but it is usually present with the stream-tin. As Prof. Schaeffer says, it cannot be separated by ordinary concentration; and while, as declared by Prof. Blake, its columbic acid may not unite with the tin in any form, yet its iron and manganese oxides may be reduced, and thus lower the quality of the tin produced, as is also the case when the smelting charge contains wolfram. To determine the effect of columbite in the ordinary potassium cyanide assay, there were assayed at the Dakota School of Mines four samples containing different proportions of columbite. The results, published in the report of the school for 1888, seemed to indi-

Jan 1, 1889

By Charles H. White

Discussion of the paper of A. L. Sweetser, Tress., xxxviii., 236. CHARLES H. WHITE, Harvard University, Cambridge, Mass. (communication to the Secretary*) :-Those interested in leaching-processes gladly welcome contributions on either laboratory-tests, such as are reported by Mr. Sweetser, or mill-tests made on larger quantities of ore; and especially valuable are such reports, even with negative results, if the methods adopted are the outgrowth of an intimate knowledge of the conditions to be met. It seems very desirable, therefore, that as complete details as possible be given in reporting on such tests, particularly with respect to the character of the ore under examination. The questions of prime importance in the sampling of ore and in the making up of charges for laboratory-tests are those respecting its grade and uniformity. In Mr. Sweetser's paper the first of these questions is answered definitely, but the answer to the second, although apparent on inspection of the results, might be more strongly emphasized with advantage, since it is only on account of the extreme uniformity of the ore that the satisfactory results obtained could have been expected. It seems advisable to call attention to the fact that for average ores, and more particularly for uneven, or 11 spotted ores, the quantities used by Mr. Sweetser are not usually regarded as sufficient to insure satisfactory results. Let us examine the method somewhat in detail. The ore was crushed to pass a 5-mesh screen, and a sample of 45 lb. was taken out for assay and tests. The diameter of the largest grain of this ore, according to Richards,1 was 2.67 mm.-assuming here, as in the following cases, that the wire of the screen was of the largest size used for the purpose, thereby giving any possible advantage in this respect in favor of the method. The table in Richards's book, p. 852, shows that 45 lb. is a sufficient quantity for a fair sample with uniform ores, but not sufficient

Jan 7, 1908

By Gerard Matthes

ONLY in recent years has any practical headway been made in the application of aerial photography to geological problems, and up to the present time its principal value to the geologist and mining engineer has been in "areal geology;" i. e., the study of formations as revealed at the surface. The object of this paper is to set forth briefly the principal advantages that may be derived from aerial photographic data in geological work and to serve in a measure as a guide to those who may be con-templating its use. Geophysical prospecting has for object the locating of mineral under the surface. Inasmuch as the geologist's chief complaint in life is a dual one-inability to see under the surface and inability to visualize comprehensively what he does see on top of the ground-geophysical prospecting coupled with aerial photography should do much to lessen his burdens. To what extent aerial photography can be made a useful adjunct to geophysical prospecting remains to be proved, but the inference drawn here is that it holds many alluring possibilities. To avoid disappointments, it should be stated at the outset that to the :geologist or mining engineer an aerial photograph or mosaic is only a tool, the effecient use of which he must set out to master. Upon his skill and ingenuity in applying it to particular problems will depend largely the value of the results that he will obtain. Under the most favorable conditions an aerial mosaic or even a few loose photographs, because of the exceptionally comprehensive oversight which they afford of field data, such as dips and strike observations at isolated outcrops, local indications of faulting, mineral and fossil finds, greatly facilitate study and correlation, save much tedious foot work, and may repay their cost many times. Even so, types of country may be found where the most, skillful use of the best of pictures will produce results so meager as to render the cost of aerial photography entirely unwarranted.

Jan 1, 1928

By executive order of the President, dated June 25, 1918, the investigation of matters relating to gas warfare, which had been initiated by the Director of the U. S. Bureau of Mines early in 1917, and had been continuously maintained and improved since, that time, was transferred to the recently created Division of Gas Warfare of the War Department. On the occasion of this transfer, both the President and the Secretary of War took occasion to speak most highly of the efficient service that had been rendered by the Bureau of Mines. It gives us great pleasure to reproduce here a letter from the President and from the Secretary of War, bearing on this subject and also to append a brief review of the work of the Bureau of Mines, prepared by its Director, Mr. Van H. Manning. The White House, Washington. June 26, 1918. MY DEAR MR. MANNING: I have had before me for some days the-question presented by the Secretary of War involving the transfer of the chemical section established by you at the American University from the Bureau of Mines to the newly organized Division-of Gas Warfare in which the War Department is now concentrating all the various facilities for offensive and defensive gas operations. I am satisfied that a more efficient organization can he effected by having these various activities under one direction and control, and my hesitation about acting in the matter has grown only out of a reluctance to take away from the Bureau of Mines a piece of work which thus far it has so effectively performed. The Secretary of War has assured me of his own recognition of the splendid work you have been able to do, and I am taking the liberty of enclosing a letter which I have received from him, in order that you may-see how fully the War Department recognizes the value of the services. I am to-day signing the order directing the transfer. I want, however, to express to you my own-appreciation of the fine and helpful piece of work which you-have-done, and to. say that this sort of team work by the bureaus outside of the direct war-making agency is one of the cheering and gratifying evidences of the way our official forces are inspired by the presence of a great national task. Cordially yours, Dr. Van. H. Manning, WOODROW WILSON. Chief, Bureau of Mines, Department of the Interior. War Department, Washington, June 25, 1918. MY DEAR MR. PRESIDENT: In connection with the proposed transfer of the chemical section at. American University from the Bureau of Mines to the newly constituted and consolidated Gas Service of the War Department, which you are considering, I am specially concerned to have you know how much the War Department appreciates the splendid services which have been rendered to the country and to the Army by the Department of the Interior, and especially by the Bureau of Mines under the direction of Dr. Manning. In the early days of preparation and organization, Dr. Manning's contact with scientific men throughout the country was indispensably valuable. He was able to summon from the universities and the technical laboratories of the country men of the highest quality and to inspire them with enthusiastic zeal in attacking new and difficult problems which had to be solved with the utmost speed. I do not see how the work could have been better done than he did it, and the present suggestion that the section now pass under the direction and control of the War Department grows out of the fact that the whole subject of gas warfare has assumed a fresh pressure and intensity, and the director of it must have the widest control so as to be able to use the resources at his command in the most effective way possible. The proposal does not involve the disruption of the fine group of scientific men Dr. Manning has brought together, but merely their transfer to General Sibert's direction. Respectfully yours, NEWTON D. BAKER.

Jan 9, 1918

By Zay Jeffries

THE metallic products of today represent the temporary end point of the efforts and interplay of thousands of years of the human struggle for existence, for pleasure, for conquest, for defense, for improvement in the standard of living, and for the satisfaction of that irrepressible urge to discover and utilize the materials and laws of nature Each metal has gained its place in the sun in severe competition with all other materials, be they metallic or nonmetallic Each serves better than any other for certain purposes. The compromise between cost and properties usually determines the selection of a metallic product for a given use. There are exceptions, as in wartime when the availability at a certain place at a certain time may far outweigh the ordinary economic considerations. In many instances superior properties are vastly more important than cost. If this were not so, the metal industry, for practical purposes, would be the iron industry. The use of 38,000,000 metric tons of newly produced nonferrous metal during, the five-year period from 1940 through 1944 is ample evidence that the special properties of these many metals have great economic value. In fact, our extensive industrial advances would have been quite impossible without the great range and variety of properties and combinations of properties of the nonferrous metals. This observation is not made to detract in the slightest way from the dominant role played by iron and steel. During the past century the production of pig iron has constituted well over 90 per

Jan 1, 1947

By Walter McDermott

THIS machine is an improvement on the well-known endless traveling belt used for dressing slimes in many mills ; the chief point of difference, and constituting the essential advantage of the present over the old form, is the application to the machine of a secondary agitating or shaking motion, in addition to the ordinary progressive motion of-the belt. In the machine as heretofore made, the inclined belt or apron moved slowly up against a thin stream of water and ore, depositing the concentrations carried over in a tank placed below, through which the belt travelled, of course, in a reversed position. By reference to the accompanying drawings, it will be seen that in this main principle the new modification does not differ materially; but the means by which it is carried out are essentially different. The machine consists of a substantial frame of mood, F, Figs. 41, 42, and 43, within which hang the shaking frame and rollers, B B, A, Endless apron ; B, Apron frame and rollers ; C, Driving drum ; D, pulleys; El Shaft and connecting rods; F, Wooden frame; G, Shaft of regulating Pulley ; H, Yokes. supporting the upper half of the travelling apron, A, which passes below around the driving drum, C, in the water-tank, J. On leaving the water-tank, the belt passes over the guiding and tightener pulley, G. The ends of the shaking-frame, B, are provided with iron yokes, H H, bored to admit the shafts of the end rollers, and carrying a lug, by which attachment is made to the connecting rods,

Jan 1, 1875

By Frank Fahrenwald

INTRODUCTORY A COMPLETE list of the elements as given for 1915 includes 18 that melt above 1,700° C. There does not exist one complete thermal equilibrium diagram for any pair of these 18 elements. Several of these elements have been combined, in relatively small proportions, with metals of lower melting point: e.g., tungsten, molybdenum, and vanadium, in steels, or with nickel and cobalt; but of this refractory group, platinum is the only one that has been extensively studied in this connection. When one considers that, with few exceptions, the industries have made use of alloys to the exclusion of pure .metals, it is reasonable to expect that alloys of this refractory group will invade fields in which the pure metals have found little application. The past neglect of this class of metals has, no doubt, been partly due to the rarity of some of them, for even though alloys of very valuable properties should be developed, their cost, unless in exceptional applications, would be prohibitive. There is also a well-founded reluctance to undertake research involving very high temperatures which, in the case of most of these elements, must be accompanied by an inert atmosphere as well. This combination of high temperatures* and control of atmosphere within the heating chamber of any furnace of present design is a difficult problem. It is the purpose of this paper to give results,1 of an investigation of one binary series of this group, in which methods were employed that avoided the usual difficulties accompanying high-temperature alloy investigation.

Jan 6, 1916

By Marcel Daly

IN a preceding paper 1 the writer has pointed out some apparent relationship between the distribution, on the Surface of the globe, of the known hydrocarbon deposits and the disposition of the principal zones of deformation of the earth's body (geosynclines). He wishes to present some further remarks on this subject. Petroleum deposits, or their derivatives or descendants, are found through the whole range of sedimentary strata, from the pre-Cambrian to the Quaternary. For instance, the pre-Beltian (Shuswap) series of the Canadian Cordillera are interbedded with limestones which are sometimes rich in carbonaceous matter (Sicamous limestone) ; and the Beltian system of the same region contains layers of argillites and dolomitic limestones which are equally high in carbon content.2 This carbon may be interpreted as the last remnant of hydrocarbons previously contained in the rocks. On the other hand, the actual formation of hydrocarbons wider conditions that would eventually permit their deposition in modern sediments is conceded by some geologists.3 Between these two extreme limits, bitumens are found indifferently in all sedimentaries. They constitute a continuous series, some kind of a large family, whose individual members may be entitled to a community of origin and probably represent the differentt stages of evolution of the primitive, parent matter. . The kinship between petroleum and such substances as asphalt, ozocerite, manjak, grahamite, albertite, etc., is well known; and E. H. Cunninggam-Craig has recently shown how intimately shale fields and oil fields are connected. For this reason, no distinction is made in the present

Jan 8, 1917

By E. A. von Hahn, T. R. lngraham

Cementation rates ulere studied by rotating an elec-tropolished or etched copper strip in aqueous solutions, of either perchloric acid or alkaline cyanide, containing silver ions. The rates of cementation were more rapid in acidic media than in cyanide media. In both, the rates varied with the rate of rotation of the copper strip. The deposits formed in the acidic solutions were finely divided, loosely adhering powders. Those formed in the cyanide solutions were dense and adherent. The presence of the deposits influenced the cementation rates. In the acidic solutions the rate was enhanced, possibly because of the increased cathodic area. In the alkaline solutions the rates were decreased in the presence of the deposits. This has been attributed to restricting the diffusion of the copper ion from the rnetal outward into the bulk of the solution. In an earlier paper1 the authors described a kinetic study of the cementation of palladium on copper in perchloric acid solutions. That work indicated that there were two stages in the palladium cementation process. The first, more rapid stage was consistent with rate control by the diffusion of Pd11 ions to the copper surface and/or by chemical reaction at the surface. The second stage was consistent with rate control by the diffusion of copper ions from the copper surface, through the deposit, out into the main body of solution. The effect of the type of deposit on the rate of cementation is of particular interest because it may be one of the primary features involved when large quantities of metal are to be cemented from solution. No substantial investigations of the effect seem to have been made. Accordingly, an extension of the previous work was arranged to study the cementation of silver on copper. This system was selected because of the convenience of the analytical methods, the previously established technology with copper, and the fact that the system could be studied in both acidic and alkaline media. By selecting perchloric acid and alkaline cyanide solutions as the media, it was hoped that some assessment might be made of the effects, on cementation, of having the silver ion present in a virtually uncomplexed state and in a highly complexed state. EXPERIMENTAL The cementation rates were studied, as previously described,' by rotating a copper strip (1.0 by 23.2 cm) clamped to the peripheral surface of a lucite cylinder. The solutions were kept at constant temperatures (±0.05°C) under an atmosphere of purified nitrogen, and samples were taken periodically for analysis. The initial solution volume was 1000 ml and the sample volume 5 ml. The initial silver(1) ion concentrations were made low (0.5 to 1.0 x 10-4 moles per liter) to minimize the influence of the cemented deposit on rates. The solutions were prepared by dilution of suitable aliquots of silver perchlorate and silver cyanide stock solutions. Both stock solutions were prepared from purified silver powder (Johnson, Matthey, and Mallory Ltd.) with redistilled deoxygenated water, and they were kept under an atmosphere of purified nitrogen. To prepare the stock solutions, weighed amounts of silver powder were dissolved with nitric acid. For the AgC104 stock solution the silver nitrate solution was evaporated twice to near dryness with perchloric acid and then made up to volume: For the NaAg(cN)2 stock solution, the silver ions were precipitated with sodium hydroxide solution. The precipitate was filtered, washed thoroughly with redistilled water, dissolved with 1.1 times the required stoichiometric amount of sodium cyanide solution, and made up to volume. The small amounts of free perchloric acid and sodium cyanide present in the stock solutions were disregarded in the preparation of the solutions. The copper strips were cut accurately from 0.025-in. sheet (American Metal Climax OFHC brand) and annealed for 1.5 hr at 470°C in a stream of nitrogen. Analyses of the solution samples for silver and copper were done with a Techtron Model AA-3 atomic absorption spectrophotometer. Calibration standards of the same composition as the experimental solutions were prepared and analyzed simultaneously with the samples. No difficulty was experienced in the analyses, and the reproducibility was within 1 to 2 pct in both alkaline cyanide and perchloric acid solutions.

Jan 1, 1968

By J. L. Huitt, D. K. Lowe

This laboratory flow study covers propping agent transporl in horizontal fractures as influenced by the characteristics of the propping particles, fluid and fracture. Correlations are presented for the transport of particles, deposition and fingering through dunes. For particles moving individually, the article velocity in some cases may be low compared to the hulk average fluid velocity; in other cases, the particle velocity may exceed the bulk average fluid velocity. At high propping agent concentration or low fluid velocity, the likelihood of particle deposition and dune formation increases. Fingering and channeling accompany dune formation. Dune formation can be limited to the outer region of tile fracture by adjustment of pump rate, fluid viscosity and particle concentration. A method is presented by which pump rate and fluid vircosity may he selected to control dune formation for given propping agent concentrations. INTRODUCTION The area and flow capacity of a fracture predominantly control the stimulation derived from hydraulic fracturing. Generation of fracture area exposes the rock matrix to a flow channel; the flow capacity of the fracture controls the flow through the channel to the wellbore under a given pressure gradient. This paper pertains to an important factor that affects the flow capacity of a fracture: the transport of the propping particles in the fracturing during the hydraulic fracturing treatment. With a better understanding of particle transport, fracturing treatments may be designed to obtain more effective distribution of the propping agent. RELATED STUDIES In recent years, the approach to obtaining high fracture flow capacity has been partial monolayer propping. Three papers1-3 have dealt with various facets of this concept. However, in some papers dealing specifically with particle transport, the results generally indicate that packing the propping particles within a fracture is inevitable. In early work&apos; with a sand slurry flowing in a pie-shaped flow cell, qualitative results showed that particle deposition in a fracture during transport should be expected. In other studies"" correlations based on slurry flow in vertical linear flow cells showed particle deposition was primarily a function of fluid velocity. In a recent paper the rate of sand advance (movement of dunes) in a horizontal linear flow cell was discussed. Subsequently, a method was given for designing fracturing treatments, based on the extent of sand advance during a treatment. In this work, particles whose diameter was small relative to the fracture width (i.e., dl W< 0.2) were primarily considered. The particle transport approaches that of sand transport in a stream bed. The industry trend, however, has been to use larger size propping agents. That is, particles with diameters approaching fracture widths predicted by Perkins and Kern.&apos;&apos; This trend has led to generally better fracturing treatments with particle relative sizes in the range 0.2 <d/W < 1.0. In all of the particle transport studies previously cited, the fluid characteristics were discussed. However, little or no attention was given to the parzicle characteristics. In this study the particles. as well as the fluid and fracture, are considered. VARIABLES AFFECTING PARTICLE TRANSPORT In the exploratory work to set LIP a program for this study, it was noted that particles within a batch moved at different velocities in a horizontal linear flow cell. In some cases the particles moved independently. In others there was particle interference. Also, particle deposition and fluid fingering occurred in some cases (Fig. 1). As a result of observing the easily distinguishab&apos;le types of particle movement, the particle variables as well as the fluid variables were included. In addition, the fracture width was included because the fluid velocity profile surely must affect the movement of the larger particles differently than that of smaller particles. Particle variables were density, diameter (based on a sphere of equal volumetric displacement), long and short dimensions, drag coefficient and velocity. Fluid variables were density, viscosity, yield shear strength and velocity. Fracture variables were the width and the angle between the plane of flow and a horizontal plane. Two factors which may prove to be important were omitted because of the complexity resulting from the parameters cited above. These are the fracture-surface roughness and gross irregularities that cause changes in the direction of flow. EXPERIMENTAL EQUIPMENT AND PROCEDURE A linear parallel-plate flow cell (Fig. 2) was used in the study. Lucite plates 1 in. thick formed the test section and permitted a viewing section 11 ft long and 10 in. wide. Spacing between the plates was adjusted with shims to give fracture widths 1/36 to 1/2 in. The model could be tilted to an angle of 45" with the horizonltal plane. Fluid flow was maintained with a Moyno positive displacement pump. Single particles were placed in the flow stream with a particle injector. A .4 - in. diameter plunger moving at a constant rate in a

Jan 1, 1967

By J. C. Smock

THE magnetic iron ores of New Jersey are found in the northern part of the State, in the Highland Mountain range, which runs from the New York line on the northeast, to the Delaware River, near Easton, at the southwest. The same range continues across Orange County to the Hudson River, and towards the southwest it is known in Pennsylvania as the South Mountain. It is more properly an elevated table-land, quite deeply furrowed by several narrow, longitudinal valleys, and shorter cross-valleys or gaps. The ridges or lines of elevation, as well as the lower valleys, conform in their general direction very closely to the general trend of the whole belt or table-land, that is, from northeast to southwest. This also agrees with the prevailing strike of the rocks. This great uniformity in the altitudes of the hills and ridges, and the direction of the lines of depression corresponding to the strike of the strata, point to an original table-land, which, through the long action of denuding agents, has been quite deeply eroded, giving rise to the present surface configuration, so that some of the former and uniform features have been partially obliterated. The very few cross-valleys or depressions are much more irregular in their course, and serve as outlets through which the drainage is carried either into the Kittatinny Valley on the northwest, or to the broad, red shale and sandstone plane bounding the highlands on the southeast. The area of this highland

Jan 1, 1874

By T. M. Morris

R. T. Hukki (Finland Institute of Technology, Helsinki, Finland)—Two schools of thought are developing concerning the order of the rate of flotation. The paper by Morris is intended to show experimental evidence in favor of the first order rate. Arbiter, on the other hand, has presented an earlier paper" to demonstrate the validity of the second order rate equation. Unfortunately his method of plotting is open to criticism, as pointed out by Morris." A more sensitive method of plotting has been described by the writer,= whereby the data presented by Arbiter demonstrate the superiority of the second order plot. The general rate equation may be written in the following forms for the integrated first and second order equations: (A) t = -1/k In Co-R/Co (first order) [4] 1 (B) 1/t = - kCo + kCo2 1/R (second order) As a first approximation the value of Co may be taken as a unity, 100 pct or 1. Whether or not this is the case in all tests performed by Morris is impossible to judge, owing to the fact that the flotation times are extremely short, e.g. 150 sec in tests A. It would, indeed, be very interesting to know what the total recovery R would be after 1 hr of flotation, for example, instead of after 150 sec. Certainly there are circumstances when C, approaches unity within a very small margin of error. Morris has used the same approximation in his example D "since the feed to this cleaner

Jan 1, 1954

By W. W. Little

At the United Verde mine the 9-2D stope on the 4050 ft level is located within the north sulphide mass lying some 800 ft north of the main sulphide ore body. In 1948 it was estimated that this block contained 85,000 tons of ore at 4% copper and 9.2% zinc. The north ore body is a lenticular replacement deposit in the black schist, extending from about 100 ft above the 3750 level to a distance below the 4500 level yet to be determined. Although the mineralized zone approaches 1000 ft in length, only 300 ft is of economic importance. In width it varies from a maximum of 60 ft to about 3 ft at the north end, and is characterized by pinching and swelling in the ore zone. One of these larger swells is being mined as the 9-2D stope. Mining costs at greater depth, together with the expected grade of ore after dilution, necessitated a low cost mining method to permit profitable stoping operations. Based on the results obtained in a number of Canadian mines, it was decided to develop the ore body for stoping by the Aldermac or bench method of diamond drill blastholes; however, this plan was subsequently changed and the radial or ring method adopted. Such a method seemed to offer the advantage of large tonnages at low cost, and obviate the necessity of waste fill. This latter point was of particular importance, since the present waste system does not extend below the 3000 level.

Jan 4, 1950

By J. C. Smock

The magnetic iron ores of New Jersey are found in the northern part of the State, in the Highland Mountain range, which runs from the New York line on the northeast, to the Delaware River, near Easton, at the southwest. The same range continues across Orange County to the Hudson River, and towards the southwest it is known in Pennsylvania as the South Mountain. It is more properly an elevated table-land, quite deeply furrowed by several narrow, longitudinal valleys, and shorter cross-valleys or gaps. The ridges or lines of elevation, as well as the lower valleys, conform in their general direction very closely to the general trend of the whole belt or table-land, that is, from northeast to southwest. This also agrees with the prevailing strike of the rocks. This great uniformity in the altitudes of the hills and ridges, and the direction of the lines of depression corresponding to the strike of the strata, point to an original table-land, which, through the long action of denuding agents, has been quite deeply eroded, giving rise to the present surface configuration, so that some of the former and uniform features have been partially obliterated. The very few cross-valleys or depressions are much more irregular in their course, and serve as outlets through which the drainage is carried either into the Kittatinny Valley on the northwest, or to the broad, red shale and sandstone plane bounding the highlands on the southeast. The area of this highland

By John E. O’Rourke, Kevin M. O’Connor, Pamela H. Rey

INTRODUCTION The resurgence of coal mining activity in the United States, brought on by the spiraling costs of fossil fw1 energy in the Seventies, has come at a time of intense public concern for the quality of the environment. Notwithstanding pressure on our economy to develop alternate sources of fue1 energy to the import of oil, the legislatures of several states have reacted to public concern over the environment by passing strict regulations aimed at con- trolling the subsidence effect s of underground mining. Agencies of the federal government charged with assistance to the mining industry, including the Department of Energy and the Bureau of Mines, have sponsored a number of instrumentation and field measurement projects aimed at the development of subsidence prediction models that can aid the mine operator&apos;s task of subsidence control. There are good empirical models developed in Europe for subsidence prediction, but they were made possible by a large body of mining-induced subsidence data collected there over a long period of time. No com- parable subsidence data base exists in the United States, and consequently empirical modeling of subsidence is not a realistic approach for our near term needs. Moreover, the geologic and topographic diversity of the several coal regions in the United States is expected to necessitate the development of several empirical models, each one expected to be relevant to its own region. Because of the time and costs that are likely to be involved in an empirical modeling approach, it is considered more expedient and cost effective to develop a general, mechanistic model for subsidence prediction purposes. In order to develop such a model, it is necessary to investigate and quantify the mechanics of the subsidence process from the mine level up to the ground surface. The series of projects discussed in this paper are designed to achieve this objective and include the following work: (1) the identification of geotechnical instrumentation that will pro- vide mine level overburden and surface subsidence data. (2) a field demonstration of selected instruments, and (3) documentation of case histories for complete subsidence mechanics, using the demonstrated and preferred instruments. An identification of feasible instrumentation and monitoring techniques was completed by Woodward-Clyde Consultants (WCC) in 1977 (O&apos;Rourke and others). This paper discusses a demonstration of those instruments at a mine in Utah, and at two subsequent projects, currently underway at longwall mines in Colorado and West Virginia. &apos;he latter two projects when complete will provide documented case histories of subsidence mechanics. The process of optimizing subsidence instrumentation and monitoring techniques to the conditions encountered during installation and monitoring for these underground mines is shown to be an evolving one, and one which has had some notable successes to date. INITIAL DEMONSTRATION The initial design and demonstration of selected monitoring systems was carried out at the SUFCO No. 1 mine, near Salina, Utah. The instrumented panel was approximately 152 m wide. 640 m long. and was 290 m to 320 m deep. The mined height of coal. seam averaged 2.4 m. The mining method was room and pillar using continuous mining machines. This method allowed some monitoring of the supported condition during development, and eventually allowed monitoring of a caved system when both chain pillars and room pillars were extracted on retreat. The two instrument systems shown on Table 1 were selected from the earlier feasibility report for demonstration at SUFCO No. 1. Collectively, the two systems, one for a fully-supported mining method and the other for a fully-caved method, incorporate most of the instrumentation to be found within all five systems listed in the earlier feasibility report. The instrumentation includes surface, subsurface and mine monitoring installations. All of the SUFCO instruments selected to meet the specifications of the general instrument types listed on Table 1 were manually operated. That is, data from the installed system could only be obtained while a person was there to physically observe or operate the system readout. Automatic data recording equipment was available for some installations, but the objectives were to keep the systems as simple as possible for the demonstration project. A complete description of the surface, sub- surface and mine level instruments, and the demonstration project results are given in WCC (1982), and selected features are discussed in this paper.

Jan 1, 1982

By Arthur S. Dwight

From the latest and best literature on lead-smelting, little can be learned concerning the present state of the art of mechanical feeding in the United States. H. O. Hofman, in his Metallurgy of Lead (5th ed., 1899), briefly describes the main features of the system in use at Pueblo, Colo., and later (p. 235) says " the only successful mechanical feeding, as far as the writer is aware, is that found at the works of the Pueblo Smelting and Refining Co." H. F. Collins, in his Metallurgy of Lead and Silver (London, 1899), covers American practice pretty thoroughly; but as to mechanical charging, he says: "The German plan of taking off the gases by means of a small iron pipe suspended in the center, and the plan of charging by means of cup and cone, as in iron blast-furnaces, have both been tried, but have not found favor, chiefly on account of the difficulty of obtaining free access to the furnace-shaft for barring, etc., with such devices."&apos; . H. W. Hixon, in his Notes on Lead and Copper Smelting (3d ed., New York, 1900), gives a description and drawing of the Hixon feeding device, as originally installed at East Helena. Evidence that this system of feeding has passed its experimental stage, and deserves more serious consideration than it has heretofore received, is furnished by two large plants—the Pueblo and the East Helena—of the American Smelting and Refining Co., where mechanical feeding has been in continuous and successful operation for a considerable period; one new plant now erecting at Salt Lake City, Utah, and one old one belonging to the same company, the El Paso works, now being rebuilt after a disastrous fire, in both of which mechanical feeding is to be a prominent feature ; one new plant of an independent concern at Torreon, Mexico, which will adopt mechanical feeding; and a number of other smaller plants, among

Jan 1, 1902

By Horace V. Winchell

The laws here referred to are those which define the status of the prospector for mineral deposits in the soil or beneath it, establish his methods of procedure, protect him in his possession while searching for the subterranean treasures, and give him assurance of title when all required conditions have been fulfilled and valuable minerals discovered. Regulations for the operation of mines and the safety and health of mine employees are likewise subjects of Federal and State legislation, but are not within the scope of the present program. Various features of our present laws will be discussed in detail by able students of the subject, and specific remedies will be proposed for the most glaring defects. It is my purpose to present in this paper a summary review of the reasons why revision is needed and demanded by the great majority of those in daily contact with the industry. Reason Number One The first objection to the continuance of the present law is that it was not planned by its framers and the Congress which passed it to apply to many of the kinds of mineral deposits, nor to the mining conditions, which are controlled by it to-day. In 1866, under the title, "An Act granting the right of way to ditch and canal owners over the public lands, and for other purposes," was surreptitiously smuggled into existence our first mining law (14 Stats. at Large, Chap. 262, p. 251). This law provided that "whenever any person or association of persons claim a vein or lode of quartz or other rock in place, bearing gold, silver, cinnabar or copper, having previously occupied and improved the same according to the local customs or rules of miners in the district where the same is situated," etc., a patent might be granted an certain conditions. This was evidently an Act intended to validate claims already initiated, and to accord Federal recognition to mining locations made in

Jan 1, 1915