Search Documents

By R. R. French

Investigations were conducted by the lndiana Geological Survey for some dry methods of bene-ficiating low-grade gypsum ore. Seventy-two batch and continuous flow tests were performed with a roller mill, rod mill, pebble mill, electronic color sorter, electrostatic separator, and an air separator. Approximately 650 size analyses and 550 chemical analyses were performed during the investigation. Batch samples were tested by the Survey, and most of the continuous flow tests were handled by com-mercial laboratories. INTRODUCTION Although many companies producing gypsum have been interested in dry beneficiation, very little information has been published in the past. One of the most comprehensive investigations was reported by the Canadian Department of Mines.5 Other reports of interest have been published by the Canadian Department of Mines,' the South Australian Department of Mines,2 and the U.S. Bureau of Mines.3 Some beneficiating practices, such as hand picking, selective mining, crushing and screening, milling, and air classifying, were already in use in the Canadian industry prior to MacPherson's investigations.5 MacPherson examined the effect of tabling, air separation, screening, flotation, electrostatic separation, calcining, washing, and various types of milling, in his efforts to eliminate dolomite, limestone, and small amounts of silica and clay from the gypsum ore. RAW MATERIAL Gypsum and anhydrite occur within the lower part of the St. Louis Limestone (Mississippian) in southwestern Indiana. Gypsum in single beds 10 or more ft thick occur at Shoals, Martin County; near Freedom, Owen County; near Bloomfield, Greene County; and in the Devonian strata of LaPorte County. Only the Shoals deposit has been exploited commercially. The western edge of the Shoals deposit is contaminated by a continuous bed of shale, about 1 1/2 to 2 ft thick, near the top of the evaporite and by thin continuous strata or irregular masses of carbonate rock. The low-grade material used in these investigations was obtained from the waste pile of the National Gypsum Co.'s plant at Shoals. The waste ore averaged about 67.4% gypsum and was contaminated by various amounts of shale, dolomite, and limestone. All the material had been previously crushed and screened to minus 1 1/4 to plus 3/8 in. X-ray analyses of powdered, sedimentated, gly-colated, and heat-treated samples of the shale showed that it was composed of slightly structurally disordered illite, Fe-rich chlorite, and very finegrained disseminated silt. The clays and silt were partly cemented with carbonate material. Light-gray argillaceous limestone and gray or brown porous dolomite made up most of the carbonate rock contamination. Crushing Characteristics: The rate unweathered gypsum, carbonate rock, and shale reduce in size was determined by crushing handpicked samples in a rod mill and screening at minus 100 mesh (.0059 in.). Fig. 1 graphically represents the data. These data indicate that carbonate rock should be relatively easy to separate from gypsum, but that shale should be difficult to separate from gypsum by differential crushing. Controlled Samples: Eight rod mill tests of hand-picked samples of mixed gypsum and shale and mixed gypsum and carbonate rock were made. Sample weight and crushing weight were standardized, but the scalping screen size was varied from 3 to 10 mesh (.265 to .0787 in.) in order to obtain the optimum purity and recovery. The data obtained from the tests (see Table I) illustrate that the relatively hard carbonate rock allows appreciable beneficiation (13.6 to 18%), but the low strength gypsum and shale allows only minimal separation (3.1 to 7.5%).* Semi control led Samples: During the investigation considerable slaking of the shale was noted when the ore was subjected to alternate wetting and drying. As demonstrated in laboratory tests, as much as 76% shale can be removed by two cycles of wetting and drying in a 48-hour period with subsequent screening at .265 in. Five ore samples, stockpiled and weathered, were screened, rod-mill crushed and rescreened at .157 or .187 in. with excellent results (Table 11).

Jan 1, 1967

By Thomas D. West

A short time ago, I had occasion to cast iron plates 1 in. thick, direct from metal containing Si, 0.51; 8, 0.045; Mn, 0.75; and P, 0.094 per cent. Much to my astonishment, I found that there was no trouble in planing them; whereas, if cupolaimetal of like composition had been used,*the planing would have been a difficult operation. I have often noticed a greater fluidity or " life " in furnace-metal, as compared with the cupola-product. Iron can be seen flowing down the furnace-runners from 50 to 100 ft., and reaching the last pig-bed in satisfactory condition, while cupola-metal might have solidified before it had flowed so far. I have seen Bessemer iron, which, on account of its low phosphorus-content, does not have the " life " of ordinary foundry-iron, held in a 30-ton ladle for nearly an hour and a half; and after skimming off the coke-dust, it still had to be cooled off' considerably before being cast. As a general proposition, it is known that the lower sulphur-content and the frequently higher temperature of direct-metal, compared with the same iron remelted in the cupola, has much to do with its greater life; yet some problems connected with this phenomenon seem to call for further study. For instance, furnace-metal containing more than 1 per cent. of silicon holds carbon, which is separated later as "kish." This separation does not take place to any great degree while the metal is very hot; but during its gradual cooling, at times, the kish is given off in such large quantities as to cover the ground from 20 to 30 ft. around the ladle. In making castings of direct-metal, especially with a high content of silicon, the separation of kish becomes an annoyance. Perhaps this throwing out of the excess of carbon makes the life of the metal shorter, after it has been remelted in a

Jan 1, 1905

By E. E. Malouf

With the continued development of low-grade porphyry copper deposits by open pit mining, substantial amounts of copper-bearing strip material have been accumulated in waste dumps adjacent to the many large mines. Since the end of World War II, the production of copper from leaching these copper-bearing wastes increased from approximately 4% of the total copper production to 10% by the early 1960's. Projected increases will probably raise this figure to 20 to 30% by the early 1970's. Furthermore, a gradual recognition of the economic feasibility of leaching mined-out areas is evident and will undoubtedly contribute additional production. Waste dumps in canyons and gulches on the periphery of open pit mines, mine stopes, caved areas, and abandoned open pits often contain substantial quantities of leachable rock ranging in concentration from 0.1 to 0.4% copper. Recent developments in the leaching of copper, mainly the recognition of bacterial oxidation of sulfide minerals combined with better under- standing of the control of the salt content of the leach solutions, both by adjusting the pH and/or by hydrolysis, are resulting in a greatly expanded recovery of copper from these hitherto uneconomic mine rejects. 11.5-1. Mechanism of Leaching. Leaching processes for the extraction of metal values from mine ore or waste may be classified for convenience as either chemical leaching or bacterial leaching. Chemical leaching is considered to be the extraction of soluble salts by metathesis in acidic, basic, or neutral water solutions. The reactions involved may be evaluated by chemical thermodynamics. Bacterial leaching, although a chemical process, is dependent on biological catalysis and this is generally a much more complex process. This justifies its separate treatment in the application to leaching. Acid ferric sulfate solutions are commonly employed in the mining industry to leach valuable metals from metal sulfide ores. The leaching mechanism is a reduction-oxidation reaction in which minerals are oxidized at the expense of ferric sulfate. Such chemical leaching is profitable when

Jan 1, 1968

By Brahm Prakash, R. Schuhmann

Chemical conditions for flotation and nonflotation of cassiterite and fluorite with oleic acid as collector and with alizarin dyes as modifying agents were studied by means of small-scale, vacuum-flotation tests. Artificial cassiterite was prepared fot these tests by high-temperature methods, especially by crystallization from borax melts. FLOTATION test work on Bolivian tin ores some years ago led to the development of several workable schemes of selective soap flotation, but left unanswered many questions of soap-flotation chemistry.' Accordingly, the study of the activation and soap flotation of quartz just reported? was undertaken as a start toward the elucidation of some of the unanswered questions. The experimental work on quartz flotation consisted primarily of small-scale, vacuum-flotation tests in which activator and collector additions and pH were varied between wide limits. In the work to be described in this paper, the soap flotation of cassiterite and fluorite was studied by the vacuum-flotation technique developed in the previous study of quartz. Using oleic acid as collector, conditions for floating cassiterite and fluorite in the absence of modifying agents were first determined. Then the effects of barium, calcium, and alizarin dyes on the flotation of cassiterite, fluorite, and quartz were studied. Alizarin dyes were chosen for study because of the promise they have shown as selective modifying agents in the flotation of non-sulphide minerals.12,1 Also, they form a family of reagents in which there should be a systematic correlation of chemical properties with composition. As a preliminary to the study of cassiterite flotation, an investigation of the preparation of synthetic cassiterite and X ray studies of natural and synthetic cassiterite were undertaken. Experimental Methods The flotation technique and most of the reagent preparations were described fully in the previous paper.' In addition, for the present work it was necessary to prepare satisfactory stocks of clean cassiterite and fluorite and to obtain samples of alizarin dyes. Cassiterite: High-grade cassiterite from the Netherlands East Indies was crushed, sized, and cleaned

Jan 1, 1951

By Brahm Prakash, R. Schuhmann

Chemical conditions for flotation and nonflotation of cassiterite and fluorite with oleic acid as collector and with alizarin dyes as modifying agents were studied by means of small-scale, vacuum-flotation tests. Artificial cassiterite was prepared fot these tests by high-temperature methods, especially by crystallization from borax melts. FLOTATION test work on Bolivian tin ores some years ago led to the development of several workable schemes of selective soap flotation, but left unanswered many questions of soap-flotation chemistry.' Accordingly, the study of the activation and soap flotation of quartz just reported? was undertaken as a start toward the elucidation of some of the unanswered questions. The experimental work on quartz flotation consisted primarily of small-scale, vacuum-flotation tests in which activator and collector additions and pH were varied between wide limits. In the work to be described in this paper, the soap flotation of cassiterite and fluorite was studied by the vacuum-flotation technique developed in the previous study of quartz. Using oleic acid as collector, conditions for floating cassiterite and fluorite in the absence of modifying agents were first determined. Then the effects of barium, calcium, and alizarin dyes on the flotation of cassiterite, fluorite, and quartz were studied. Alizarin dyes were chosen for study because of the promise they have shown as selective modifying agents in the flotation of non-sulphide minerals.12,1 Also, they form a family of reagents in which there should be a systematic correlation of chemical properties with composition. As a preliminary to the study of cassiterite flotation, an investigation of the preparation of synthetic cassiterite and X ray studies of natural and synthetic cassiterite were undertaken. Experimental Methods The flotation technique and most of the reagent preparations were described fully in the previous paper.' In addition, for the present work it was necessary to prepare satisfactory stocks of clean cassiterite and fluorite and to obtain samples of alizarin dyes. Cassiterite: High-grade cassiterite from the Netherlands East Indies was crushed, sized, and cleaned

Jan 1, 1951

By R. K. Iyengar, G. C. Duderstadt

An investigation was carried out to determine the effect of Ca-Si additions on the dissolved oxygen content of liquid steel. An apparent equilibrium was reached after holding the melt for some time when the total oxygen content of the melt was identical with the dissolved oxygen. Results of the investigation show that for deoxidation with silicon and manganese the apparent equilibrium is reached after 8 to 12 min and the oxygen content of the melt is in good agreement with values reported in the literature for similar steel compositions. Ca-Si additions decrease the dissolved oxygen content appreciably below that obtained with Si-Mn deoxidation. It is postulated that some calcium dissolved in liquid steel at the time of its vaporization combines with dissolved oxygen to form CaO which then fluxes the manganese silicate, thereby lowering the activity of the deoxidation products. Slow flotation of calcium silicate inclusions is attributed to their slower growth rate. An addition of aluminum (to yield <0.005 pct Alsol) prior to introduction of Ca-Si improves the kinetics of removal of resulting deoxidation products. WITH the introduction of continuous casting of billets and blooms, application of calcium-containing alloys for deoxidation purposes has gained new interest. More so than in conventional ingot casting, the degree of control of the dissolved and total oxygen contents in steel for continuous casting can determine the success or failure of the operation because these affect both surface (pinholes) and internal quality of the billets. Of the available deoxidizers, only silicon has so far found wide application. However, in the typical range of application (0.20/0.30 pct Si), it is too weak a deoxidizer to suppress pinhole frequency to the level desirable for all but the least demanding appli-cations (approximately 10/50 pinholes per sq ft, de-pending on degree of subsequent reduction). On the other hand, Vincent&apos; has shown that it requires ap-proximately 0.007/0.008 pct A1 soluble in the steel to suppress pinhole formation to <10 pinholes per sq ft. In view of the difficulty of consistently maintaining this aluminum level and the associated problem of tundish nozzle constriction2 when aluminum is added to the ladle, steelmakers have searched for other de-oxidation alloys to circumvent the problem. Calcium-containing alloys offer such a possibility. When employed as a partial substitute for silicon, CaSi (30 pct Ca/60 pct Si) additions are reported to yield adequate pinhole contro1.3 Its use simultaneously preserves the "fluidity" of the steel and ensures good castability.4 Oxygen contents as low as 0.007 to 0.014 pct have been obtained with CaSi additions varying between 3 to 8 lb per ton.5-7 Due to the high degree of vaporization of calcium at the temperature of molten steel and the different methods used to introduce it into the liquid, the reported results show considerable scatter and lack of consistency. According to several investiga- deoxidation tors, the flotation characteristics of CaSi products are not as favorable as those found for alumi-num but are similar to those established for silicates with low alumina content.678 Thus, cleanliness ratings were improved when CaSi was replaced by a com-bination of Si + A1 followed by CaMnSi additions.5,9 In view of the lack of a comprehensive description of the deoxidation potential of CaSi alloys, a study was undertaken of the effect of CaSi additions on oxygen content in comparison to Si + Mn and Si + Mn + Al. The alloy chosen for this study contained 63 pct Si, 32 pct Ca, <3 pct Al, and 2.5 pct Fe. EXPERIMENTAL PROCEDURE The experiments were divided in three groups as shown in Table I. In each group, the CaSi addition was increased successively while maintaining the melt composition constant. The experiments in the third group were designed to determine the effect of prede-oxidation with small amounts of aluminum. Ingot iron, containing 0.02 to 0.03 pct C and 0.03 to 0.05 pct Mn, was melted in a 100-lb magnesia crucible. Pig iron was added to the melt under air in an induction furnace to attain the desired carbon content of 0.05 to 0.15 pct and thereby control the initial oxygen content of the melt between 0.04 and 0.015 pct. After removal of the slag, the furnace was sealed and argon was introduced through an opening in the graphite cover, Fig. 1. When the desired temperature was reached, electrolytic manganese was added to the melt and pin samples were taken (7 mm silica tubing) to establish initial oxygen content. To obtain maximum efficiency, CaSi and metallic silicon were introduced in a sealed steel pipe into the bath. This procedure assured minimum loss of calcium through vaporization as the deoxidants were always released at the bottom of the melt. Samples were taken at regular intervals and quenched in water. Temperature of the bath was measured with a Pt/Pt-10 pct Rh thermocouple. Portions of the pin sample were used for oxygen analysis; five determinations per sample were made to obtain average oxygen content. Oxygen analyses were made by the inert carrier gas fusion method with frequent cross checks with the vacuum fusion method.

Jan 1, 1970

By B. E. Sundquist

The various methods based on solution models for obtaining free energies of mixing from miscibility-gap data have been applied to a number of binary-alloy systems. For nine of these systems there exist experimental thermodynamic data that permit a comparison of the results to experiment. It was found that the method of van der Toorn and Tiedema almost invariably leads to results that are physically unacceptable and that vary drastically with small changes in the miscibility-gap parameters. The subregular solution model is found in all cases, except the Al-Zn, Fe-Cr, and Cu-Pb systems, to exaggerate the free energy of mixing by 30 pct or more. The model developed by Lumsden is found to give results that are often in excellent agreement with experiment and which exaggerate the free energy of mixing by no more than 30 pct. These results and others give evidence that the Lumsden treatment of the effect of unequal atomic sizes and of imperfect configurational randomness due to deviations of AB bond energies from the mean of AA and BB bond energies is adequate for most systems. ANALYTIC expressions are frequently proposed for the dependence on composition of the activities of the components of a solution. Because the development of solution theory is incomplete, these expressions contain parameters which must be determined by experiment. The measurement of activities is often difficult and consequently such measurements are less readily available than are measurements of phase equilibria which, under certain conditions, can also be used to evaluate these parameters. For example, suppose it is known that two structurally dissimilar phases, each of known composition, in an n-com-ponent system are at equilibrium at a given temperature and pressure. n equations can be set up in terms of these parameters expressing the equality of the chemical potential of each component in the two phases. In addition, one can write the Gibbs-Duhem equation for each phase that also contains these parameters. Thus, if these n + 2 equations contain n + 2 parameters, these parameters can be determined (at the temperature in question) from the phase diagram alone. If the average number of parameters in each expression for the activity of a given component in a given phase is V then there will be 2nV parameters involved. Equating 2nV to n + 2 shows that, for n + 2, V = 1. If the temperature dependence of each parameter were to be expressed in some explicit form one could use equilibrium conditions at a number of temperatures to increase V. The situation is much improved when the two phases in equilibrium are structurally similar. It can then be assumed that, stably or metastably, two phases will become one at higher temperatures. Thus the number of parameters involved becomes nV instead of 2nV. Hence, V = 2 for n = 2 using only one temperature. (It is implied here that the activity expressions used are valid over the entire composition range.) In this investigation only the equilibrium of two structurally similar, two-component phases (miscibility-gap systems) will be considered. The various proposed solution models will be applied to a number of these systems and the results compared with available experimental results. All of the analytic expressions that have been proposed for the free energy of mixing of a two-component system are of the form where ?Gmix is the free energy of mixing per mole of solution, N1 and N2 are the mole fractions of components 1 and 2, respectively, and f(Ni, T) is some function of composition and temperature. In the "ideal" solution model f = 0. In the "regular" solution model f = a constant. Since these two models permit only a symmetric equilibrium diagram they will not be considered further here. The simplest model that permits a nonsymmetric miscibility envelope is the so-called "subregular" solution model proposed by Hardy.1 This model gives where the Ci(T) are functions of temperature only. The same expression for f is obtained from the "linear a function" model proposed by Darken and Gurry2 and applied to miscibility-gap systems by Wriedt.3 This model requires that the a function defined by be a linear function of composition (yi is the activity coefficient of component i). This model is not purely hypothetical for it has been found2 to hold true for a number of systems. It is readily shown3 that the f(Nl, T) obtained from this model is of the form given in Eq. [2]. It will be noted that the subregular solution model contains only two parameters and hence both of them can be determined at any desired temperature below the critical temperature, Tc, for a miscibility-gap systems in the manner described previously. At T, the two constants can be determined by equating the second and third derivatives of ?Cmix with composition to zero. Another two-parameter model was proposed by Lumsden4 who set

Jan 1, 1967

By G. Czupryna, S. Natansohn

Electrowinning is the prevalent technique for recovering silver from wastes generated in silver-tungsten electrical contact fabrication. Such scrap is placed in a permeable plastic basket, which constitutes the anode compartment, and is suspended in a larger cell where the cathode is mounted. A silver nitrate solution is used as the electrolyte and, upon application of an electric field, the silver migrates to the cathode where it deposits. At times, there is tungsten migration to the cathode compartment and consequent co-deposition with the silver. This W contamination, which may amount to several thousand mg/L (oz per gal), necessitates additional purification of the deposited Ag and its removal would, therefore, be advantageous. Eliminating the W impurity also extends the operating period of the cell with corresponding increases in the Ag output and savings in labor costs. The solution to this problem lies in the selective removal of the W from the AgNO3 electrolyte either by liquid-liquid or liquid-solid extraction. Although W extraction in the liquid-liquid mode with a quaternary amine or other reagents as extractants appears feasible, particularly in view of the low pH (about 1.5) of the system, this approach was not considered because it is essentially a batch-type process. It is a more elaborate industrial operation than extraction by ion exchange resins. Implementing the latter process consists of passing the electrolyte from the electrowinning cell through an ion exchange column which would extract the tungsten selectively and returning the tungsten-free stream to the cathode compartment. This process continues until the W extraction efficiency decreases (as a result of resin loading) below an acceptable value. The electrolyte is then directed through another, similar column while the W values are eluted off the first one and the resin is regenerated for another cycle. Thus, two columns in a parallel flow pattern provide the means for continuous processing of the electrolyte feedstock.

Jan 1, 1984

IN describing the mining and treatment of ore at the Broken Hill Proprietary mine E. J. Horwood, superintendent of mines, gave the following account of the development of flotation there. It was in 1902 that the recovery of zinc from the ore by flotation was hit upon. The former general man-ager, Mr. Delprat, directed our then research officer, Mr. Carmichael, to try boiling the tailing with salt cake of which there was a considerable tonnage left over from the leaching process. The idea was the possibility of dissolving the zinc. Carmichael made the. Experi-ment, but, rather discouraged, took the glass beaker down to the general manager&apos;s office, remarking that he could not get the stuff to settle. On showing the beaker to Mr. Delprat, the latter recognized the marked distinction between the black scum on the surface and the rest of the tailings, and exclaimed: "Why, this is the very thing we are after; the zinc is floating!" Patents were applied for at once, but later on it was found that another investigator, Potter, had already hit upon the idea of flotation. His patents, however, were so involved with other operations that his process was impracticable. Litigation followed, but in the end the B. H. P. paid the Potter Company a substantial sum as settlement. In the case of Carmichael&apos;s beaker, the acid in the salt cake acted on the small amount of carbonate present in the ore, producing CO. bubbles. Owing to the aversion of sulfide crystals to being wetted, the gas as generated attached itself to the zinc in in-creasing quantities until there was sufficient to buoy the zinc particle to the surface. This action went The next problem was to apply the principle on a commercial scale, and this involved much experiment and developmental work. Various kinds of sloping copper pans with gas jets below to maintain the tem-perature were first tried, but were found too slow and too costly in operation.

Jan 6, 1928

By B. C. Burgess

AFTER many years of close and friendly association with talc and soap-stone, this orthographically distinguished mineral steps forth in this edition, for the first time in a chapter of its own. Pyr, the Greek for fire, and phyllite, a rock or stone, form its name and at the same time refer to the first recorded use of pyrophyllite as firestones or hearthstones. Another derivation of "phyllite" is from the Greek phyllites, "of leaves," alluding to the beautiful white radial crystal aggregates that form when pyrophyllite is heated. Pyrophyllite used by the Chinese for carving is called agalmatolite, from the Greek agolma, meaning an image. COMPOSITION AND PROPERTIES Pyrophyllite has previously been grouped with talc because of the close similarity of the minerals in physical and optical properties. They have the same space group; and chemically they are closely related, pyrophyllite being the aluminum silicate A12Si4010(OH)2 and talc the magnesium silicate Mg3Si4010 (OH) 2. Another arrangement of the pyrophyllite formula is generally given as A12034Si02H20 because it expresses the chemical composition as usually determined (alumina 28.3 pct, silica 66.7 pct, water 5.0 pct). Vanderbilt gives pH values of pyrophyllite 5.6 to 8.4.29 Pyrophyllite usually is white, pale green, cream or pale yellow, buff or light gray. It is found in darker shades and other colors principally due to oxidation of contained iron minerals. It is translucent in thin sections. In hardness it is 1 to 2 in the Mohs scale. Its specific gravity is 2.8 to 2.9. In bulk specific gravity, the powdered mineral ranges from 0.4 to 0.7. Its luster is pearly to dull; it is infusible in the Bunsen burner flame, slightly affected by aqueous solutions of sodium carbonate and hydrochloric acid. It is decomposed by sulphuric acid, with separation of gelatinous silica. It is characterized chiefly by its micaceous structure and cleavage, its softness and greasy feel. Two other varieties occur

Jan 1, 1949

By F. N. Rhines, B. H. Alexander

MUCH attention has been directed to the effects of grain size upon the properties of alloys, but there has been scant study either of the conditions that determine the pattern and dimensions of den-drites in metal systems, or of the influence of their shape and size upon the overall properties of cast-ings. The aim of the research that is about to be described has been to investigate the effect of vari-ous factors upon the mode of formation of dendrites in alloys by measurements of the distance between adjacent dendrite arms (dendrite spacing). Early investigators, including Grignonl and Tschernoff,2 showed that a metal dendrite is com-posed of a tree-like system of stalks and branches arranged in a simple geometrical pattern. North-cott and Thomas3 demonstrated that, in the face-centered cubic solid solutions of copper-base, these stalks and side arms all lie in (100) directions in the crystal. Several investigators, including Sauveur and Chou,0 Sauveur and Reed,&apos; and Martin and Mar-tina have reported that the addition to steel of alloy-ing elements, such as nickel, chromium, and molybdenum, not only makes the dendrites easier to reveal by etching, but makes them coarser. The latter authors8 proposed that the coarsening of the dendrites is roughly proportional to the increase in the temperature range of freezing, caused by adding the alloying elements. Sauveur and Chou6 showed, in addition, that the dendrites are coarsened by a decreased rate of cooling of the casting. Measurement of Dendrite Arm Spacing Among the physical conditions that could be ex-pected to have an influence upon the dendrite arm spacing, that appears in a cast metal, are: composi-tion, rate of freezing, crystal structure, and type of constitution. The relationships obtaining between these variables and the dendrite dimensions have been examined, in the present research, by measur- ing the arm spacing in a wide variety of alloys, listed in tables II through VI. Alloy compositions are recorded in the tables by showing the symbol of the major metal followed by the percentage and symbol of the alloying agent; thus, "Al-10Ag" is an aluminum-base alloy containing 10 pct of silver. Although none of the alloys were analyzed, an im-pression of their degree of purity may be obtained from that of their component metals given in table I. Five hundred grams of each alloy was made by melting in small clay-graphite crucibles in an elec-tric muffle furnace. After alloying the temperature was adjusted to 50" to 75°C above the liquidus and the melts were poured into cast iron molds, at room temperature, the molds having a wall thickness of 1 in. and a cavity 11/2 in. sq in cross-section. Each ingot, thus cast, was sectioned at mid-height and the sectioned surface was polished and etched for metallographic examination. Dendrite spacing meas-urements were made at three positions, namely, ad-jacent to the mold wall, midway between the wall and the center of the ingot, and at the center (desig-nated e, m, and c respectively, in the tables). A typical series of microstructures is presented in fig. 1. For each measurement, the average was taken of the dendrite spacing of several grains covering a zone about 2 mm wide. Only those grains which had a major dendrite axis nearly in the plane of polish were selected in order to eliminate corrections for orientation differences from grain to grain. Although the dendrite spacings were measured to the nearest thousandth of a millimeter, the values listed in the tables are thought to be significant only to the nearest hundredth of a millimeter. The larg-est difference in readings found, when various ob-servers rated the same specimens, was 0.012 mm; the largest difference between corresponding meas-urements upon duplicate specimens was 0.027 mm.

Jan 1, 1951

By S. Kobayashi, A. E. Armenákas, C. Mylonas

Earlier work1-4 has shown that commercial mild steels under static loading at the lowest natural operating temperatures fracture in a brittle manner only when damaged by a suitable history of straining. Notched and then compressed plates have fractured in subsequent tension at loads as low as 10 pct of the limit load and precompressed smooth bars at a subsequent extensional strain as low as 0.01. The comparison of the average net fracture stress with the flow limit stress was shown to be an excellent criterion of brittle or ductile behavior of mild steel structures when only loads and general stress levels are known. The present investigation shows that the deformation at fracture is a far more sensitive measure of brittleness than the fracture stress. Both criteria, deformation and stress, are used to determine the amount of uniform precompression of two mild steels, ABS-B and Project E-steel, resulting in brittle fracture under the strong constraint of a subsequently machined severe circumferential groove. The fracture stress equaled or exceeded the theoretical flow limit Ól = 2.680., (&apos;based on the elevated yield stress at each prestrain) up to prestrains of about 0.20 and then fell off to about 1 at prestrains of 0.60. Yet a prestrain of only 0.05 reduced the elongation at the shoulders by a factor of about 4. The total plastic elongation of a region surrounding a sharp notch in prestrained steel deternines whether or not fracture will be initiated in large structures, hence is a direct and realistic measure of the remaining ductility and provides an excellent test of the material&apos;s resistance to embrittlement. ALMOST all engineering structures of mild steel which failed in service in a so-called "brittle" manner exhibited appreciable local plastic deformation (more than 1 pct) and a mixture of "cleavage" and "shear" fracture surfaces. Furthermore, the peak local stress in an advancing crack is always high. Such simple criteria as pure cleavage, absence of plasticity, or fracture stress, so useful in other fields, are insufficient to characterize brittleness in engineering structures at ordnary temperatures. The "brittle)&apos; behavior of engineering structures is caused by the limited ductility at cracks or notch regions, as shown by recent work at Brown University summarized and extended in Refs. 1 to 4. It was also shown that the local ductility of mild steel may be catastrophically reduced by a suitable strain and temperature history similar to those which may occur in real structures. Localized yielding begins at the notch roots at low loads but is contained by surrounding elastic regions. The plastic strains are hence small. They increase slowly with the load up to the flow limit or limit load for an ideally plastic material. Unrestricted plastic flow then occurs. At such strains the real material locally st rain-hardens and fractures. With work-hardening materials no flow limit exists, and the transition from low to high plastic strains is gradual but increases more rapidly at loads close to the flow limit of an equivalent perfectly plastic material. When the available ductility is sufficient for reaching the limit load, the behavior is normal or "ductile". With insufficient ductility, fracture will occur at a low load and will be defined as "brittle". Accordingly the sufficiency or not of the ductility at a notch is reflected in the magnitude of the fracture load or average net stress as compared with the limit load or flow limit. The application of this criterion gave surprising results. Service failures under semistatic loading occurred mostly below the limit load, hence were "brittle". On the contrary all static tests with undamaged commercial mild steels reached the limit load in spite of the deepest notches and temperatures below Charpy impact transition (say about -30°F or higher). Notched bars showed no brittleness even under fully dynamic axial loading up to 1.5 x107 psi per sec at -23°F and about 2.5 x l06 psi per sec at -ll0°F, but broke in a brittle manner at -200°F and l03 psi per sec.&apos; To propagate a fracture at low load, experimenters had to trigger it by superimposing a strong dynamic impact at a notch cooled by liquid nitrogen as in the Robertson5 or Esso tests.&apos; Once started the cracks would run through warmer regions of smaller stress. Obviously the ductility of the apparently undamaged commercial steels was "sufficient" in the laboratory tests but not in the service fracture, where it must have been reduced by some embrittling procedure of fabrication or service. These conclusions were confirmed by the achievement of low static stress (brittle) fracture initiation in unwelded steel after a local reduction of ductility by simple prestraining. Symmetrically notched plates of undamaged mild steel cooled below the Charpy V-notch transition range were tested in central static tension: Undamaged plates withstood loads of limit intensity, but when subjected to prior in-plane com-pressive prestraining perpendicular to the notch axis and to accelerated aging, the plates fractured completely or partially at very low static loads, as low as one-tenth of the flow limit.2-4 However, damage could not be easily related to the strongly variable prestrain around a sharp notch. To obtain easier strain measurements, it was decided to use axially precom-pressed bars and bent bars. Final testing was done by

Jan 1, 1970

Economic Significance of High-grade Concentrates BY PAUL M TYLER AND CARLE R HAYWARD (Min & Met, Dec, 563 4000 words) Generally pyro¬mctallurgical methods yield a higher recovery but cost more per ton of ore treated Milling methods are inherently cheaper for the reason that they do not involve dissipa¬tion of heat energy in slag formation, ctc It is vaguely realized that the smelter man could do a better job if he were supplied with purer raw materials but hard¬headed mill men have been offered little inducement to do a really good job of cleaning concentrates To do this may involve some sacrifice in percentage yield and in mill capacity and unless there is a compensating saving in freight and smelter charges, it simply is not good business to go beyond a certain point in the way of making clean concentrate Opportunities exist for eliminating one or more steps in the expensive series of processes for recovering various metals, or at least reducing the volume of materials that has to be handled at the most costly steps The beneficiation of nonmetallic minerals likewise affords numerous examples of over-all economies obtainable through more refined methods of mechanical improvement All this leads to the conclusion that perfecting selective processes for isolating pure minerals (e g, galena) virtually free from other sulfides as well as gangue may be productive of industrial economies Conversely, cheapening smelting methods may invade the field of mechanical improvement of ores but, as Kiphng said, that is another story

Jan 1, 1937

By H. M. Crankshaw

The early methods of mining anthracite in the steep pitching Mammoth bed consisted in driving breasts up the pitch from the gangways and airways driven in the bed along the strike (Plate 2, Fig. 1). Breasts are simply rooms driven up the pitch the full thickness of the bed (Plate 2, Fig. 2), having a width of from 18 to 30 ft., and a manway or traveling way on one or both sides. (For detail of breast method see Whildin, Trans., vol. 50, p. 704). Many difficulties were encountered, and the maintenance cost of the timbered gangways was so great as to be practically prohibitive. To reduce this expense, the gangways were driven in the thin Skidmore bed underlying the Mammoth, and the coal mined through rock holes. (Plate 2, Fig. 2, A.) It was found that after the breasts were driven up 80 to 100 ft., the coal almost invariably rushed or "ran away," making good ventilation almost impossible and the extraction of coal from the upper portion of the lift very difficult. The economic length of a lift is from 200 to 250 ft., and the percentage of extraction by the old method above mentioned was often under 50 per cent., while the coal recovered was so badly broken up as to reduce materially the percentage of large sizes. Principles of Present Mining Methods The present methods designed for the recovery of a maximum percentage of coal and a maximum yield of the prepared sizes depends largely on the following principles: First.—Formerly the practice in mining bituminous coal was to space rooms so that as much coal as possible could be extracted in first mining (Plate 3). The small pillars were often lost, and an improvement in total extraction was found in the system of driving narrow rooms with wide pillars, with a much larger final recovery (Plate 4). Second.—The early method of ventilation was to maintain a single

Jan 1, 1917

By R. Ellerman

The hydrometallurgical processing of an impure zinc oxide fume is described. Flowsheet includes roasting for fluorine elimination and countercurrent leaching to produce a neutral sulphate solution. This solution is combined with zinc sulphide leach solution for subsequent purification and electrolysis. Novel to the neutral leach step is the use of automatic pH control. THE electrolytic zinc plant of the Hudson Bay Mining and Smelting Co. Ltd. was erected in 1929-1930 to process zinc sulphide concentrates produced from ore mined at Flin Flon, Manitoba. Since 1930, production of high purity slab zinc has been continuous. In May 1951, construction of a fuming plant was completed and operations were started to recover zinc from copper smelter reverberatory slag. A second zinc-bearing material in the form of an impure zinc oxide fume was then made available for treatment. Coincident with the construction of the fuming plant, additions were made to the electrolytic zinc plant to recover the zinc in the fume as slab metal. The original plant capacity of 70 tons of slab zinc per day was steadily increased up to May 1951, at which time the daily production averaged 130 tons. With the advent of the fuming plant and the processing of zinc oxide fume, production was stepped up to the present capacity of 190 tons per day. Of this, approximately 48 pct is contributed by the processing of zinc oxide fume. This additional source of raw material has allowed a 20 pct cutback in mining and milling operations, thereby adding considerably to the life of the Flin Flon mine. Zinc sulphide concentrates are treated by the usual hydrometallurgical method. Details of this operation and plant were described by Carr and Reikie in 1935&apos; and Kent in 1951.8 The impure fume is treated in two operations. First, it is roasted to eliminate fluorine. Next, it is subjected to a countercurrent leach with spent electrolyte to extract the zinc as a neutral zinc sulphate solution. During this leaching step, soluble impur-

Jan 1, 1956

By H. C. George

As the basis for a round table discussion of Petroleum Engineering Education for the February, 1930, meeting of the Petroleum Division, A. I. M. E., the following questions were sent to about 60 of the leading engineers and educators in the petroleum industry: 1. Should there be any changes in the curricula of our courses in petroleum engineering to meet the changing demands of the Industry? If so, what changes?] 2. Should courses in petroleum engineering be offered through university extension? 3. Should the universities offer correspondence courses in petroleum engineering? 4. What should be the character of the graduate work offered in petroleum production engineering? 5. Should summer work in the oil fields, on pipe lines, or in oil refineries be required of undergraduates? If so, how much and of what character? The following men replied to the questions: G. B. Corless, Humble Oil & Refining Co., Houston, Texas. J. R. McWilliams, Skelly Oil Co., Tulsa, Okla. W. W. Scott, Humble Oil & Refining Co., Houston, Texas. H. H. Power, Gypsy Oil Co., Tulsa, Okla. L. G. E. Bignell, Oil K. Gas Journal, Tulsa, Okla. E. L. Estabrook, Pan American Petroleum & Transport Co., New York, N. Y. F. P. Donohue, Pan American Petroleum & Transport Co., New York, N. Y. C. 0. Rison, lndian Territory Illuminating Oil Co., Bartlesville, Okla. L. B. Holland, Phillips Petroleum Co., Bartlesville, Okla. H. J. Kemler, Shell Petroleum Corpn., St. Louis, Mo. C. A. Bonine, Pennsylvania State College, State College, Pa. J. 0. Lewis, Dunn & Lewis, Tulsa, Okla. A. G. Heggem, Tulsa, Okla. J. M. Lovejoy, Petroleum Bond & Share Corpn., New York, N. Y. B. B. Boatright, Colorado School of Mines, Golden, Colo. A. C. Ruble, Union Oil Co. of California, Los Angeles, Calif. J. B. Umpleby, Goldelline Oil Corpn., Oklahoma City, Okla. R. S. Knappen, Gypsy Oil Co., Tulsa, Okla. K. C. Heald, Gulf Companies, Pittsburgh, Pa. K. C. Sclater, Exchange National Bank Bldg., Tulsa, Okla. F. G. Tickell, Stanford University, Stanford University, Calif.

Jan 1, 1930

By A. Mitchell

An approximate phase diagram has been developed for the CaF2-CaC2 system, indicating a eutectic point at 1240°C, Ncac2 = 0.13, and no detectable solid solution in either phase. The liquidus line is shown to correspond to a simple c22- ion in solution. A thermo-chemical study of&apos; the reaction between carbon-saturated Ni-Ca alloys and CaC2-CaF2 liquids indicates that lhe Raoullian activity coefficient of CaC2 in dilute solution in Cap2 al 1500°C lies between 8 and 10. Some effects of the stabilily of Cap2-CaC2 solutions at high temperatures on electroslag remelting praclice are outlined. THE alkaline earth acetylides. MIIC2, have a reasonably high thermochemical stability at high temperature in the solid state,&apos; with the exception of magnesium, which forms an unstable acetylide at low temperatures (-500°C) and a carbide, Mg2C3, in the range 700&apos; to 1000°C. The acetylides of calcium and barium have been shown to have limited solubility in their respective chlorides,&apos; and further these solutions contain the acetylide as a C: ion.&apos; The equivalent magnesium solutions have not been studied. Although calcium "carbide" is used as a desulfuriz-ing reagent in steelmaking. and is possibly present as an acetylide-oxide phase in very basic electric arc practice slags, the acetylide ion appears to be substantially unstable in a silicate slag.* As a conse- *This instability arises from equilibria in the reaction: CaC2 + CO = (Ca0) + 3C where the low intrinsic solubility of CaC2 in silicate lattice, and the low activity of CaO in a silicate solution where CaO/Si02 < 1, combine to give a very small equilibrium concentration of CaC2 in solution in such silicate slags at temperatures in the region of I 500°c, even under carbon-saturated conditions. Under highly basic conditions, a liquid CaO-CaC2 phase may separate from the silicate system quence of this, the possibility that reactions involving CaC2 in silicate solutions are of importance to general steelmaking practice is remote. However, in operations involving a slag primarily based on a halide, or alkaline earth oxide, we must take into account the possibility that CaC2 will appear in quantities sufficient to significantly affect both the chemical and physical properties of the slag. The work outlined below presents a study of the CaF2-CaC2 system intended to provide sufficient data to allow an estimate of the importance of this system to electroslag remelting and welding practice. However, we should indicate at this point that there will be other processes, e.g., heat treatment, flux cleaning of castings, fused salt electrolysis, and so forth, where alkaline-earth halide fluxes are in contact with carbon, graphite, or carbides, and where halide-acetylide solutions must be taken into account. EXPERIMENTAL 1) Structural Studies. In view of the difficulty ex-perienced in handling CaC2 prepared from calcium turnings and propane gas at 700°C, it was decided to use solutions prepared directly in the equilibration apparatus, Fig. 1. The starting materials were: a) Ni-Ca-C alloy, prepared by adding calcium to liquid nickel held under calcium fluoride in an induction-heated graphite crucible; b) calcium fluoride, prepared by fusing calcium fluoride powder (British Drug House "EXTRA PURE") calcium fluoride in an induction-heated graphite crucible, in air, followed by electrolysis between graphite electrodes at 1 amp cm-2 density, for 10&apos; coulombs per g CaF2. This procedure decomposes the CaO produced by hydrolysis during the fusion step, replacing it by CaC2; Ca2+ + 2e-Ca*(l) Ca*(l) + 2C(gr)-(CaC2)caF2 O2- -2e-O*(g) O*(g) +C(gr)-CO(g) This results in a composition of between 2 and 5 wt pct CaC2 in CaF2. Fifty grams (in lumps) of this material were placed in a graphite crucible, together with Ni-Ca-C alloy (averaging 20 wt pct Ca), and the equilibration apparatus assembled. The alloy reacted with the crucible at high temperature to give CaC2, which dissolved in the calcium fluoride solution to give the desired composition. Cooling curves were plotted manually for these liquids, with rapid stirring and CaF2 seeding to minimize supercooling, and using a Pt/Pt 13 Rh thermocouple calibrated on the freezing points of nickel and copper. This gave a reproducibility of ±0.l°C. and an absolute accuracy of the thermocouple of ±l°C. An example curve is shown in Fig. 2, with the CaF2 end of the binary system in Fig. 3. The CaF2-CaC2 ingots were crushed, under dry nitrogen, and sampled for chemical analysis and X-ray examination. Analytical details are given in the Appendix. Powder diffraction data indicated that the only phases present in all samples examined were calcium fluoride and tetragonal (Types I and 111) calcium acetylide,4 with no evidence of solid solutions or compound formation. 2) Thermochemical Studies. The apparatus used to obtain activity data on CaC2 in these systems is shown in Fig. 4. It consists of an arrangement whereby the graphite crucible and its contents (CaF2-CaC2. Ni-Ca-C) can be rapidly cooled without exposure to air. Trial experiments to determine an equilibration time by ap-

Jan 1, 1969

A New Microscopy and Its Pntentialities. By Charles S. Barrett. (Metals Technology, .April 1945) Physical Metallurgy Fundamental Principles Involved in Segregation in Alloy Castings. By R. M. Brick. (Metals Technology, Sept. 1944) A Stud) of Age-hardening Using the Electron Microscope and Formvar Replicas. By D. Harker and MI J. MurphyI (Metals Technology, June 1945) Standards for Identifying Complex Twin Relationships in Cubic Crystals. By C. G. Dunn. (Metals Technology, April 1945) Orientation Changes during Recrystallization in Silicon Ferrite. By C. G. Dunn (Metals Technology, April 1945) The Orientation Texture at the Surfacr of Cast RIetals. By Gerald Edmunds. (Metals Technology, Jan. 1945) (With discussion) Internal Friction of Single Crystals of Brass, Copper and Aluminum. By George H. Found. (Metals Technology, June 1945) (With discussion) Recrystallization of Aluminum in Terms of the Rate of Nucleation and the Kate of Growth. By W. A. Anderson and R. F. Mehl (Metals Technology, Feb. 1945) (With discussion) Copper and Copper-rich Alloys Textures, Anisotropy and Earing Behavior of Brass. By F. H. Wilson and R. ill. Brick. (Metals Technology, June 1945) (With discussion) Phantom Laminations in Brass. By Daniel R. Hull, H. F. Silliman and John R. Freeman, Jr. (Metals Technology, Jan. 19451 (With discussion) Corrosion of Yellow Brass Pipes in Domestic Hot-water Systems—a Metallographic Study. By E. P. Polushkin and Henry L. Shuldener. (Metals Technology, Oct. 1944) (With discussion) The .Alpha Solid Solution Field of the Copper-manganese-zinc system. By R. S. Dean, J. R. Long, T. R. Graham and .%. H. Robersori. (Metals Technology, June 1945) A White High-manganese Brass. Ry K. S. Dean, J. R. Long, T. R. Graham and C. W. Matthews. (Melds Technology, June 1945) Magnesium Alloys Oxidation Inhibitors in Core-sand Mixtures for Magnesium Castings. By O. Jay Myers. (Metals Technology, Feb. 1945) (With discussion) Grain Size and Properties of Sand-cast Magnesium Alloys. By R. S. Dusk and C. R. Phillips. (Metals Technology, Feb. 1945) (With discussion) Rater Quenching of &apos;Some Typical Magnesium Casting Alloys. By R. S. Busk and R. E. Anderson (With discussion)

Jan 1, 1945

By W. S. Cavender

The Round Mountain mining district, Nye County, Ne- vada, was discovered in 1906 on claims owned by Lewis D. Gordon. Initial mining operations uncovered gold veins of spectacular richness, and within a few days of discovery, Gordon sold his controlling interest for some $87,000. From this sale emerged the Round Mountain Mining Co., predecessor of Nevada Porphyry Gold Mines, Inc., the latter destined to become the major property owner in the area. Vein mining in the district continued sporadically into the early 1930s, yielding 9.3 Mg (330,000 oz) of gold plus substantial silver credits from approximately 626 kt (690,000 st) of ore. In addition to the lode deposits, the early miners recognized the placer potential in the alluvial fan material accumulated around the west and north sides of Round Mountain itself. Intermittent placer operations were carried out for a number of years, and in the 1940s and 1950s, Round Mountain Gold Dredging Co. worked the placers under a lease from Nevada Porphyry Gold Mines. The last placer operation terminated in 1959 when it, like some of its predecessors, proved uneconomic. Total placer production for the district is estimated at 3657 km (4 million yd) of gravel containing 59 Mg (210,000 oz) of gold and possibly 2.0 to 2.3 Mg (70,000 to 80,000 oz) of silver. Round Mountain is a small hill situated on the east flank of the Toquima Range in central Nevada. The hill is com- posed of relatively flat-lying Tertiary rhyolitic ash flow tuffs, which overlie Paleozoic metasediments and Cretaceous granites. Throughout the surrounding Round Mountain mining district, most of the known gold ores occur in the tuffs, although the metasediments and granites are also mineralized. Mineralization is structurally controlled, principally by a series of northwest-trending shears and shattered zones. Vein, stockwork, and disseminated ores occur, usually containing simple quartz-pyrite-gold mineral assemblages. The gold itself is electrum, having a silver content of 30% to 40%. In September, 1967, Elwood Dietrich, a prospector and mine promoter, obtained a purchase option on the 4452 ha (1 1,000 acres) of mineral rights held at Round Mountain by Nevada Porphyry Gold Mines. The original option had a buy-out price of $1 million and was established through Dietrich&apos;s friendship with officers of Nevada Porphyry. In April, 1968, Dietrich conveyed his option to Ordrich Gold Reserves Co., a partnership created by a group of west coast investors, mostly employees of the airline industry. There- after, Ordrich invested considerable funds in trying to test and develop the property, but soon recognized the need to seek financial and technical support from the mining industry. In December, 1968, Dietrich contacted Wayne Cavender, then Regional Geologist, Southwest, for Copper Range Exploration Company (CRX) in Tucson, Arizona, and made a data presentation. Shortly thereafter, Cavender was appointed Manager of Exploration and Chief Geologist for Copper Range Co. (parent company of CRX), New York City, and he asked C. Phillips Purdy, CRX Regional Geologist, Northwest, to make an initial property examination. Purdy&apos;s one-week field study took place in March, 1969, and resulted in a recommendation that CRX pursue its investigation of the property. The presence of low-grade gold mineralization in both the alluvial gravels and in the bedrock was verifiable, but the placer was deemed to have the greater immediate economic mining potential. At that time, gold was in the $1.41/g ($40 per oz) price range. Working from Purdy&apos;s information, Cavender decided to attempt acquisition of the property, and the first in a long series of negotiations was initiated with Ordrich. Basically, CRX felt that the placer had a promising potential for several reasons, including (I) past operators had recovered free gold but not the gold contained in the pebble fraction of the gravels; (2) past operations appeared to have been ineffectively designed or managed and not costefficient; and (3) the price of gold appeared to be poised for an upward move. Negotiations with Ordrich were prolonged and difficult, with CRX competing against several ma* mining companies, but finally an agreement was reached, effective June I, 1970. Gold was then back to $35. It is believed that, in

Jan 1, 1985

Prof. Henry M. Howe, New York, N. Y. (communication to the Secretary*):—The results presented in Mr. Mathewson&apos;s paper are of very great interest. Perhaps the most interesting is that shown in Table I. and Fig. 1, in which the arsenic decreases in 10 min. from 0.22 to 0.07 per cent. This is such a large decrease that it is to be hoped that Mr. Mathewson will verify it by repeating his tests with a matte of similar composition. This is particularly to be desired, because the simultaneous removal of sulphur appears to be very small. All three blows further agree in showing that the removal of arsenic is in the very early part of the blow. The fact that the removal of arsenic then ceases abruptly cannot be explained completely by the fact that the arsenic has fallen so low as by its lowness to resist further removal, because in the first blow the arsenic becomes stationary at 0.06 per cent., whereas in the third blow it does not become stationary until it has fallen to 0.034 per cent. The abrupt ending of the removal of arsenic is more likely to find its explanation in the composition of the slag, and it is to be hoped that Mr. Mathewson will supplement these extremely valuable data with others in which the composition of the slag at the same time shall be given. The sudden rise of arsenic toward the end of the third blow I suppose must be referred to an error in sampling or analysis.

Jan 1, 1908