Search Documents

By P. W. Bakarian

Previous determinationl,2,3 of the texture of magnesium and its alloys have shown only slight variations in the principal features of the structure. This investigation presents pole figures for magnesium and two of its alloys, in which differences of some magnitude will be shown. Schmid and Wassermann have considered the texture of magnesium in analogy with that of zinc—also a hexagonal lattice. Whereas the zinc texture is said to be derived primarily through basal slip and secondarily through {IO2}† twinning, the {102} twinning is considered impossible at the later stages of the rolling in magnesium because of its smaller axial ratio. This state of affairs appears reasonable for pure magnesium, but for alloy textures the situation is more complex. A double orientation similar to that found in zinc has been reported by J. D. Hanawalt,4 and the addition of small amounts of calcium to magnesium and its alloys to produce a double texture was noted by J. C. McDonald.5 The pole figures of this investigation, using an improved X-ray technique, show these various textures. The dependence of directional properties of rolled sheet on modifications of texture is well recognized. Correlation of physical properties with existing texture should be even more significant if quantitative valuations are attached to the various areas on the pole figures. Such a quantitative technique is developed herein. Experimental Method Two alloys were used, besides high-purity magnesium. In each case, the metal was extruded to bars 1/2 in. thick and hot-rolled to a thickness of about 0.075 in. It had been established previously that such a reduction was more than sufficient to eliminate the extruded structure. The rolling proceeded in the same direction as that of the extrusion, without any cross rolling. The temperatures corresponded to normal commercial practice, averaging around 600°F. A unique method of preparing the sample was developed in this work. Instead of using a flat specimen, a stem of the metal was cut out of the rolled sheet in the desired direction (rolling direction) as shown in Fig. I. From a sheet of 0.075 to 0.065-in. gauge, the stem was cut to a square cross section with a jeweler's saw, rounded with a file and polishing paper to a diameter of 0.060 in. and evenly etched in dilute hydrochloric acid to a diameter of 0.038 + 0.001 in. In this way, a cylinder of the original sheet with its axis in the desired direction was produced. By using this type of specimen for the pin-point pictures, any variance in the absorption of the diffracted beam at the various angular settings of the specimen, was completely eliminated.*

Jan 1, 1942

By P. W. Bakarian

Previous determinationl,2,3 of the texture of magnesium and its alloys have shown only slight variations in the principal features of the structure. This investigation presents pole figures for magnesium and two of its alloys, in which differences of some magnitude will be shown. Schmid and Wassermann have considered the texture of magnesium in analogy with that of zinc—also a hexagonal lattice. Whereas the zinc texture is said to be derived primarily through basal slip and secondarily through {IO2}† twinning, the {102} twinning is considered impossible at the later stages of the rolling in magnesium because of its smaller axial ratio. This state of affairs appears reasonable for pure magnesium, but for alloy textures the situation is more complex. A double orientation similar to that found in zinc has been reported by J. D. Hanawalt,4 and the addition of small amounts of calcium to magnesium and its alloys to produce a double texture was noted by J. C. McDonald.5 The pole figures of this investigation, using an improved X-ray technique, show these various textures. The dependence of directional properties of rolled sheet on modifications of texture is well recognized. Correlation of physical properties with existing texture should be even more significant if quantitative valuations are attached to the various areas on the pole figures. Such a quantitative technique is developed herein. Experimental Method Two alloys were used, besides high-purity magnesium. In each case, the metal was extruded to bars 1/2 in. thick and hot-rolled to a thickness of about 0.075 in. It had been established previously that such a reduction was more than sufficient to eliminate the extruded structure. The rolling proceeded in the same direction as that of the extrusion, without any cross rolling. The temperatures corresponded to normal commercial practice, averaging around 600°F. A unique method of preparing the sample was developed in this work. Instead of using a flat specimen, a stem of the metal was cut out of the rolled sheet in the desired direction (rolling direction) as shown in Fig. I. From a sheet of 0.075 to 0.065-in. gauge, the stem was cut to a square cross section with a jeweler's saw, rounded with a file and polishing paper to a diameter of 0.060 in. and evenly etched in dilute hydrochloric acid to a diameter of 0.038 + 0.001 in. In this way, a cylinder of the original sheet with its axis in the desired direction was produced. By using this type of specimen for the pin-point pictures, any variance in the absorption of the diffracted beam at the various angular settings of the specimen, was completely eliminated.*

Jan 1, 1942

By Beall, John V.

THIS is not simply the story of how a water filled shaft was developed into a million-ton- a-year producing mine in the space of four critical years, although it is reason enough for telling it, but it is also the saga of an engineering achievement in which knowledge nurtured by years of experience in coal and ore mines was blended together and the best from each type of mining selected. The entire system of mining was detailed on maps by the mining engineering department before the shaft was unwatered, and subsequent development followed these plans nearly to perfection. The selection of machinery was particularly critical as it was necessary to push production from only a few headings in the early stages of development and metal mine machinery was being used in a coal panel-system of mining. At the start of World War I1 the demand for iron ore to supply Woodward blast furnaces, and rapid exhaustion of the main source of Wood- ward ore, No. 3 Red Ore mine, necessitated speedy opening of the Pyne mine. The mine is three miles southwest of Bessemer and is responsible for 80 pct of Woodward ore, the rest coming from the Songo mine. The Woodward Iron Co. is one of the old producers of the Birmingham district. S. H. Woodward, an iron-master of Wheeling, overheard two Union soldiers conversing about ore and coal lands in Alabama, which lead to the acquisition of the first ore lands of the Woodward Co. in 1869. Development was not begun until after the death of S. H. Woodward; his two sons, W. H. Woodward and J. H. Woodward, formed the Woodward Iron Co. in 1881 and purchased a tract of land midway between the ore vein on the southeast and the coal field on the northeast about 12 miles southeast of Birmingham for the

Jan 1, 1950

By Arthur S. Dwight

We author of this historical chapter will perhaps be criticized for limiting his subject to the history of the blast furnace in lead smelting, and especially to the part it played in the great custom ore-smelting business which for three decades or more was the means of opening up vast mineral treasures and practically dominated the mining industry in the Rocky Mountain region of the United States, in Mexico and in Canada. The men of that era shared the romance and the thrills of mining, and bore their part as pioneers in the building of the great West. The present writer was too young to participate in the first of the three decades mentioned, but immediately thereafter came under the apprenticeship of some of the men who had worked out the early metallurgical problems of the industry, became personally acquainted with most of the others of that group, heard the tales of early experiences, successes and failures, the gossip of the frontier and mining camps, from all of which there remain embedded in his mind clear impressions of the outstanding personalities of that time. That is the background against which the fifty years of intimate contact with the mining and smelting business and his own experiences as metallurgist stand out in his memory, and it is hoped that the gentle reader may understand and approve his desire to rescue from comparative oblivion the fundamentally valuable results accomplished by these fathers of the industry. It will be the purpose of this chapter first to narrate the general history of the growth of the industry; second, to pay tribute to some of the pioneer metallurgists, and third, to discuss some of the salient points of the metallurgical practice at different periods, to illustrate the technical progress of the art. The series of eight Annual Reports of Rossiter W. Raymondl,† U. S. Commissioner of Mining Statistics from 1869 to 1876, contain most of the available information about the early smelting operations in the Rocky Mountain region, and much is in the early volumes of the Transactions of the American Institute of Mining Engineers. The monograph by S. F. Emmons2 though not published until 1886, contained an elaborate description of the smelting works operating in 1879. Otto H. Hahn3 wrote a valuable paper in 1883, on smelting prac-

Jan 1, 1937

By L. F. Mondolfo

R301 is a clad aluminum alloy, composed of a core of a duralumin-type alloy clad with a magnesium silicide alloy. It differs from other well-known clad alloys in that the cladding and the core respond to the same heat-treatments, and therefore the cladding contributes appreciably to the mechanical properties of the material. In Table 1 are reported the compositions of the core and cladding alloy for the material used for the experiments. [ ] In clad aluminum alloys where the core contains copper and the cladding does not, at elevated temperatures the copper tends to diffuse from the core through the cladding. This fact is well known and many investigations have been conducted to determine the features of this diffusion.1-7 Most of those investigations cover materials clad with pure aluminum; the present investigation covers a material clad with an alloy. Since the cladding thickness on R301 varies with the gauge, as shown in Table 2, several gauges were investigated. [ ] MATERIAL AND PROCEDURE The material used was sheet of the following gauges: 0.025, 0.040, 0.064, 0.102, 0.170. Cut in pieces approximately 3 by 5 in., it was in the cold-rolled state and was soaked for increasing times at the following temperatures: 910°F., 940°F., 970°F. A Lindberg cyclone furnace was used for the experiments. The procedure was as follows: The furnace was started empty with controlling pyrometer set at the determined temperature. After the furnace had reached that temperature, it was run for some 20 to 30 min. empty, in order to allow the temperature inside to become stabilized. Then the first samples were introduced. A load thermocouple, with recording pyrometer, was connected with the sample of the heaviest gauge. About 10 min. was required for the material to reach temperature and the soaking time was counted from that point. After 200 min. soaking, the second group of samples was introduced without stopping the furnace. After 200 min. more, the third group of samples was introduced, and so on, until the last sample had been introduced. Every time the furnace was opened and new samples were added, a drop of temperature was registered by the thermocouple connected with the material

Jan 1, 1945

By H. J. Snyder

Both the room-temperature and 600°F (315°C) primary solid-solution phase boundaries for the silver comer of the Ag-Cd-In temary system have been determined using X-ray diffraction and metallo-graphic techniques. Solid solubility of indium in silver at room temperature and 600°F (315°C) is shown to be between 20.3 and 21.7 wt pct, and corrects the previously extrapolated value of 18 wt pct appearing in the literature. The solid solubility of cadmium in silver at room temperature, not previously established, is shown to be between 34.9 and 41.3 wt pct. The solid solubility of cadmium in silver at 600°F (315°C) is confirmed as 43.2 wt pct. The shape of the primary phase boundary line for the subject temary system appears straight at room temperature and curves con-vexly towards the solvent (silver) comer at 600°F (315°C). THIS investigation was undertaken to initiate development of the Ag-Cd-In ternary diagram by establishing the primary solid-solution phase boundary in the silver corner of the diagram. At the present time, a diagram for this ternary system is not available, while this system appears to offer potential for a variety of uses. One alloy in the system has already proven to be useful as a control rod material in nuclear reactors.1"3 To encourage additional exploration of the potential of the system an understanding of its ternary diagram would be beneficial. It is towards this end that the present study is directed. LITERATURE SURVEY In undertaking this study, a comprehensive literature survey was first conducted to find information that would be useful for guidance. Useful knowledge did result from investigating the respective solubilities of indium and cadmium in silver as indicated in the binary constitutional diagrams of the systems Ag-In and Ag-Cd and also reviewing possible shapes of ternary primary phase boundaries. Weibke and Eggers~ used metallographic techniques to establish the system In-Ag as illustrated in Fig. Is This diagram shows that silver in the solid state is capable of dissolving approximately 18 wt pct In. This solid solubility of indium in silver holds true from room temperature up to 1276°F (691°C), then decreases continuously up to 1'761°F (960.5"C), the melting point of the silver. The solid-solubility limit of indium in silver established by Weibke and Eggers has been confirmed by Hume-Rothery and Reyno1ds. G Durrant' used a method which consisted of microscopic examination of quenched specimens to establish the Cd-Ag system as displayed in Fig. 2.' The primary phase boundary of Fig. 2 proved to be in good agreement (ie., within 1 wt pct) with other studies*'1' of the Ag-Cd system made using X-rays and metallog-

Jan 1, 1968

By R. S. Archer

In the microscopic examination of aircraft-engine parts made of heat-treated alloy steels, the writer has been forcibly impressed by the failure of the usual etching processes to disclose any but gross defects in heat treatment. It seemed particularly desirable to bring out the grain size of the steel, which is indicated in the ordinary etching processes chiefly by the change in orientation of structure from grain to grain. After various attempts, a fairly successful method has been found, which is here presented in the hope that it may be of use to those who have occasion to examine these steels in the hcat-treated condition. The specimens worked with have been mostly chrome-nickel steels heat treated (that is, hardened and tempered) to a Brinell hardness of around 300. A few experiments with other specimens will be referred to later. Briefly, the method employed consists in etching the steel about 10 min. in a fresh solution of picric acid in ethyl alcohol, and then rubbing off the smudge of carbonaceous matter on moist broadcloth. Different samples of almost identical analysis, heat treatment, and physical properties (including resistance to impact) respond quite differently to this treatment. In some, the grain boundaries are developed quite readily, while in others, especially in those whose grain is unusually fine or in which the final hardening heat has not quite obliterated the previous crystallization, the results are more obscure. The exact time of etching to secure the best results also differs for various samples, and the greatest success is usually attained by a process of "tinkering." Such a process is illustrated in a series of micrographs, the first six of which were taken at a magnification of 300 diameters. The properties of the steel are as follows: Carbon, per cent............... 0.42 Brinell hardness.............. 293 Nickel, per cent................ 1.35 Yield point, pounds per square Chromium, per cent............. 0.90 inch........................ 131,000 Copper, per cent................ 0.025 Maximum strength, pounds per Manganese, per cent............ 0.74 square inch................. 144,500 Phosphorus, per cent............ 0.024 Elongation in 1 in., per cent... 28 Sulfur, per cent................ 0.036 Lod impact, foot-pounds...... 51 Reduction of area, per cent...... 57.3

Jan 1, 1920

By L. A. Willey, William L. Fink

TWO of the aluminum-alloy systems previously studied—the aluminum-titanium and the aluminum-chromium—exhibit a peritectic reaction at the extreme aluminum end of the diagram. Preliminary work indicated that the aluminum-zirconium and certain other aluminum systems were similar in this respect. The present paper, the twentieth of a series from the Aluminum Research Laboratories, reports the results of a recent investigation of equilibrium relations in aluminum-zirconium alloys of high purity, which confirm the preliminary observations. Previous Investigations There has been only one investigation of the aluminum end of the aluminum-zirconium system. Sykesl prepared and studied alloys containing 0 to 70 per cent Zr. The lowering of the freezing point of aluminum by the addition of zirconium was found to be very little, if any (less than 2" C.). He placed the solid solubility of zirconium in aluminum at room temperature between 0.57 and 0.97 per cent. A few other investigators have attempted to determine the composition of the intermetallic compounds occurring in this system. Honigschmid2 obtained the compound ZrAla as a by-product during the preparation of ZrSi2. He made no attempt to prepare other aluminum-zirconium compounds. Weiss and Newmann3 prepared an alloy by heating aluminum with a double fluoride of potassium and zirconium. When this alloy was treated consecutively with caustic soda and hydrochloric acid, there was a residue, which contained approximately 72 per cent Zr and 28 per cent A1 (Zr3AI4). Marden and Rich4 prepared an alloy in the same way, treated it with caustic soda, and obtained a residue of silver-white crystals, which contained 70 per cent Zr and 30 per cent A1 (Zr3A14). Alloys Materials Used.—Electrolytically refined aluminum was employed for thc preparation of all alloys used in this investigation. The chemical

Jan 1, 1939

By William L. Fink, L. A. Willey

TWO of the aluminum-alloy systems previously studied—the aluminum-titanium and the aluminum-chromium—exhibit a peritectic reaction at the extreme aluminum end of the diagram. Preliminary work indicated that the aluminum-zirconium and certain other aluminum systems were similar in this respect. The present paper, the twentieth of a series from the Aluminum Research Laboratories, reports the results of a recent investigation of equilibrium relations in aluminum-zirconium alloys of high purity, which confirm the preliminary observations. Previous Investigations There has been only one investigation of the aluminum end of the aluminum-zirconium system. Sykesl prepared and studied alloys containing 0 to 70 per cent Zr. The lowering of the freezing point of aluminum by the addition of zirconium was found to be very little, if any (less than 2" C.). He placed the solid solubility of zirconium in aluminum at room temperature between 0.57 and 0.97 per cent. A few other investigators have attempted to determine the composition of the intermetallic compounds occurring in this system. Honigschmid2 obtained the compound ZrAla as a by-product during the preparation of ZrSi2. He made no attempt to prepare other aluminum-zirconium compounds. Weiss and Newmann3 prepared an alloy by heating aluminum with a double fluoride of potassium and zirconium. When this alloy was treated consecutively with caustic soda and hydrochloric acid, there was a residue, which contained approximately 72 per cent Zr and 28 per cent A1 (Zr3AI4). Marden and Rich4 prepared an alloy in the same way, treated it with caustic soda, and obtained a residue of silver-white crystals, which contained 70 per cent Zr and 30 per cent A1 (Zr3A14). Alloys Materials Used.—Electrolytically refined aluminum was employed for thc preparation of all alloys used in this investigation. The chemical

Jan 1, 1939

By John F. Kendrick, Paul D. Cornelius

This paper is a progress report of a study the authors are making of the sucker-rod pump, considered as a vibrating system with one degree of freedom, with forced vibrations and with viscous damping. Dr. S. Timoshenko's formula is given, defining such a system. Each factor is considered in respect to the problem of operating sucker rods, and the zone is pointed out in which the mathematics do not apply to the sucker-rod pump, because of its variable mass. This general theory is interpreted in the light of nearly two years of testing wells in the field, and correlating the results of other tests. The motion of the pumping mechanism is a vibration. The string of sucker rods vibrates with a natural frequency. The motion of the plunger is the result of adding together these two vibrations, and is modified by a damping or friction factor. The controlling factor appears to be the ratio of the period of the natural vibration of the rod string to the period of the vibration of the pump. The first conclusion is that a definite value of this ratio, which is below resonance and is probably not greater than 0.5, should not be exceeded in order to assure satisfactory performance from the sucker rods. The second conclusion is that the component parts of the pumping equipment should be selected to give the smallest practical period of the natural vibration, and when this does not permit operation at a safe speed and give the required plunger displacement, a longer polished-rod stroke should be used. While the quantitative results are but rough approximations, the qualitative analysis of pumping problems on this basis promises to be of considerable value in diagnosing the cause of poor performance and prescribing suitable remedies. The trouble that results, whenever it becomes necessary to crowd the sucker-rod pump, to take potentials or to handle increasing volumes of water, is responsible for the belief that this type of pump is not equal to present day needs, and that it is only a question of time before some other pumping device will take its place. Of the troubles experienced, it is not surprising that the frequency of sucker-rod failures should

Jan 1, 1937

By E. B. Harden, J. H. Harden

The practical use to which topographical models or relief-maps have been put, has within the last few years taken a wider range. They are rapidly coming into favor for other than purely scientific purposes, and their value for illustration and instruction is being more fully appreciated. Topographical maps; representing by contour-curve lines the elevations and depressions of the earth's surface, are now demanded in engineering work of nearly every description, and afford a ready means of bringing out the configuration of the country in a simple manner. A beautiful example of recent topographical mapping is seen in the seventeen sheets just issued by the Geological Survey of New Jersey. By reason of the inability of unskilled persons to understand the nature of a topographical map, it is sometimes necessary to con struct the same in relief, with the rivers, canals, railroads, etc., delin eated upon it. With the aid of such a map, problems in engineer ing science which would otherwise require expert assistance to explain them, are reduced to a simple and understandable form. Relief-maps are also of value to the geologist in working out the geological structure. To the instructor they present the most ready and efficient means of imparting clear and accurate knowledge of topography and kindred subjects. To the lawyer they are invalua ble in enabling him to bring into the court-room a representation of a part of the country with all its features accurately shown, to ex plain to the court and jury the special points about which litigation is pending and which would otherwise require long and laborious description. The application of the topographical map to business purposes is shown in a relief constructed by the writers for the Cumberland Valley Railroad Company and used by that company in the various ways of calling attention to the desirability of its route. This model is based partly on actual survey and partly on sketch topography. The horizontal scale is ,%, the vertical 1/19,200 of

Jan 1, 1888

By Joseph Jenson

Total United States production for 1928 was 900,364,000 bbl. as compared with 901,129,000 for 1927, or 2,466,000 bbl. per day versus 2,468,000. The three major producing areas were Texas, Oklahoma and California. Texas production increased from 217,389,000 bbl. in 1927 to 256,888,000 in 1928—an increase of 39,499,000 bbl. following an increase of 44,500,000 bbl. in 1927. Oklahoma production amounted to 249,558,000 bbl. in 1928 as compared with 277,775,000 bbl. in 1927 and 177,650,000 bbl. in 1926. California production for 1928 was 231,982,000 bbl. as compared with 231,196,000 in 1927. Production increased markedly in Venezuela and declined in Mexico. Elsewhere no great changes or declines in production were noted. New discoveries occurred in nearly all districts. The many excellent reviews of the various districts of the United States presented at this meeting, are each fully summarized and tell their own story so well that little would be gained by attempting to repeat their content here. There are certain impressions to be gathered from these papers and certain trends that are indicated by them which may better be pointed out. OVERPRODUCTION Overproduction is the most serious one of them. Efforts to avert it resulted in a measure of cooperation in the oil industry more widespread in character and more beneficial in results than has ever been recorded in any previous year. These efforts were undertaken in the closing months of 1927 and enthusiastically effected before the spring of 1928 had passed. Unfortunately, slight advances in prices during the summer months accompanied by the letting down of this sort, of effort resulted in a marked increase of production during the latter half of 1928. Successful delay in the drilling of new prospective areas was in effect in Oklahoma. California delayed some drilling and increased its shut-in

Jan 1, 1929

By David Donoghue

Efforts made in the year 1930 and in previous years restricted production in most of the fields of Texas to a point that was satisfactory, at the beginning of 1931, to the majority of producers and buyers. In the Panhandle, North Texas and West Central Texas districts, a few operators with refinery affiliations or contracts either ignored, or by virtue of injunction suits, did not comply with the Railroad Commission's orders, and there was some oil sold at less than posted prices, which, with the Oklahoma City difficulties, caused the first general price reduction. More could have been done perhaps to help the situation on the Gulf Coast and in the Laredo district, but natural advantages are not readily surrendered. East Texas Proration troubles in 1930 were insignificant when compared with those of 1931. In January, 1931, efforts were begun to convince the producers and citizens of East Texas of the necessity of curtailment. Opposition quickly developed and meetings were held in the towns of the region and proration denounced vigorously. Notwithstanding a strenuous campaign for additional legislation waged by many producers, the regular session of the State Legislature refused to strengthen the conservation laws and passed only the Marginal Well Bill, designed to prevent the Commission from prorating small wells. The Railroad Commission held a heated hearing on East Texas in the latter part of March. During April the Commission issued three orders based on the Yates plan for the proration of the East Texas field. Each succeeding order raised the allowable for the field. In June the opposition held more mass meetings at which a plan based on acreage was endorsed. Apparently on the theory that any plan was better than none, the Commission issued an order on July 2 embodying some of the features of the proposed plan, limiting production to 250,000 bbl. per day, and dividing the producing area into 20-acre units participating equally in the outlet. Owing to the bringing in of many wells and the many violators of the Commission's orders, production increased to such an extent that prices went as low as 5c per barrel.

Jan 1, 1932

By N. Shiarella, Coleman D. Hunter, I. B. Browning

The price of crude oil in Kentucky did not change very much during 1935 until the latter part of the year, but more stabilized conditions and an increase in consumption of natural gas made the year a more profitable one than the year 1934. The production of crude oil in 1935 amounted to 5,175,054 bbl. as compared to 4,814,904 bbl. in 1934. This increase was due to two developments: (1) the application of new recovery methods to old fields, which, although in operation in the state for several years, had never before reached a point where the production obtained, while highly satisfactory where applied, was sufficient to influence the totals in the production figures; (2) the development of the Fordsville area in Ohio County, where shallow depths enabled the operators to complete the development of a large number of wells with a good flush production probably accounted for most of the increase. A map showing the location of oil and gas pools in Kentucky was published last year.' The fields of eastern Kentucky, producing from the Weir sand of the Waverly group of the Lower Mississippian series, in Johnson, Magoffin, Lawrence and Elliott counties, produced 826,001 bbl. of oil in 1935 as compared with 902,247 bbl. in the previous year. No new wells were drilled in this area during the year, except those for use as intake wells in repressuring. What has been done in the few small areas within these fields in the way of repressuring has produced results sufficient to a great extent to offset the natural decline of all the field. It is probable the drilling of new wells and construction of new plants will be such as to cause these fields to produce more in 1936 than was produced in the past year. This is based on the fact that the sand is highly favorable for repressuring and the results obtained show from 300 to 500 per cent increase in production. From the "Corniferous" pools, where production is from the Cornifer-ous limestone of Devonian age, in Lee, Powell, Estill, Wolfe, Morgan and

Jan 1, 1936

By I. B. Browning, N. Shiarella, Coleman D. Hunter

The price of crude oil in Kentucky did not change very much during 1935 until the latter part of the year, but more stabilized conditions and an increase in consumption of natural gas made the year a more profitable one than the year 1934. The production of crude oil in 1935 amounted to 5,175,054 bbl. as compared to 4,814,904 bbl. in 1934. This increase was due to two developments: (1) the application of new recovery methods to old fields, which, although in operation in the state for several years, had never before reached a point where the production obtained, while highly satisfactory where applied, was sufficient to influence the totals in the production figures; (2) the development of the Fordsville area in Ohio County, where shallow depths enabled the operators to complete the development of a large number of wells with a good flush production probably accounted for most of the increase. A map showing the location of oil and gas pools in Kentucky was published last year.' The fields of eastern Kentucky, producing from the Weir sand of the Waverly group of the Lower Mississippian series, in Johnson, Magoffin, Lawrence and Elliott counties, produced 826,001 bbl. of oil in 1935 as compared with 902,247 bbl. in the previous year. No new wells were drilled in this area during the year, except those for use as intake wells in repressuring. What has been done in the few small areas within these fields in the way of repressuring has produced results sufficient to a great extent to offset the natural decline of all the field. It is probable the drilling of new wells and construction of new plants will be such as to cause these fields to produce more in 1936 than was produced in the past year. This is based on the fact that the sand is highly favorable for repressuring and the results obtained show from 300 to 500 per cent increase in production. From the "Corniferous" pools, where production is from the Cornifer-ous limestone of Devonian age, in Lee, Powell, Estill, Wolfe, Morgan and

Jan 1, 1936

By R. F. Mehl, C. S. Barrett, A. H. Geisler

THE complicated nature of the property changes that accompany age-hardening has made it necessary to reconsider and to elaborate the simple dispersion theory.1 It has been apparent for some time that more direct information is needed concerning the atomic mechanism of precipitation from solid solution if the theory of age-hardening is to be developed past a purely qualitative stage.‡ Fortunately, in recent years information has been developed which allows us to trace in detail the lattice changes accompanying the process of precipitation from solid solution. This information relates chiefly to the sequence of the several stages of lattice alteration by which the matrix lattice is transformed to the equilibrium precipitate lattice, and permits reasonable inferences to be drawn concerning the states of internal strain that accompany these stages. This information is most complete for the solid solution of copper in aluminum. The equilibrium precipitate is the ?' phase," CuA12." This forms in plates, parallel to the {100} matrix planes. The atom pattern and atom spacing on the plane in ?' lying parallel to this plane are roughly similar to those opposite it in the matrix.' The formation of ?', however, is preceded by the formation of a transition lattice ?', which again lies parallel to the matrix {100} plane, but in this case the matching of atom pattern and spacing across the matrix-precipitate interface is nearly perfect; thus there is lattice coherency across the interface and the interface is a plane of separation in only a very limited sense.4-8 Particles of ?' may be recognized microscopically and form a well-defined Widmanstätten figure.* The ?' lattice is recognized by the occurrence of diffraction lines on powder photograms or of spots on Laue photograms which may be analyzed in the usual ways to determine the lattice type and the lattice spacings. Very recent research 6.7,1 has shown, however, that streaks occur on the Laue photogram at an earlier point in time during the aging process. These streaks have been attributed to a preferential clustering of copper atoms into small platelike elements of only a few atoms in thickness and a few hundred atoms in diameter, probably of the composition of "CuA12," which may be designated as Guinier-Preston zones or aggregates.1 It is difficult if not impossible to determine the lattice type and lattice spacing in these aggregates. It is possible1 that these aggregates are in fact merely ?' in a high state of dispersion; the inclination to argue this is strong, as we shall see later. Never-

Jan 1, 1941

By A. M. Gaudin

THE so-called Kick law' is generally accepted to . mean that for each reduction to one-half in particle diameter, in a unit weight, the same amount of work is required. In crushing-efficiency calculations on crushing tests it is customary, when basing the calculation on Kick's law, to assign ordinal numbers to each standard sieve size. These ordinal numbers increase by a constant difference with each successive sieve aperture, because standard sieve apertures are in constant ratio. Minus 200-mesh is generally assumed as equivalent to 37 microns in size. By definition, the ordinal number multiplied by the per cent material of any size is equal to the energy units in the material of that size in a unit weight of sample. The sum of all energy units is the energy units content of a unit weight of sample, whether it be crusher feed or product. The difference between the energy units in the product and that in the feed is the tangible result of the work input per unit weight of feed. From this the amount of work necessary for one energy unit may be calculated. This has been done for a quartz crushing-test made at the Intermountain Experiment Station of the U. S. Bureau of Mines at Salt Lake City, in which the net work going to crushing was carefully measured. The results of this crushing test are given in Table 1.'

Jan 1, 1929

Alfred Stansfield, Montreal, Canada:—In Professor Howe's paper on the position of Ae3, he shows its industrial importance in determining the temperature to which steel should be heated for " grain refining." Several years ago I carried out a research on the " burning " of steel and found that while hypo-eutectoid steel should be heated to Ae3, hyper-eutectoid steel that has been very much overheated must be reheated to the curve Sa on the carbon-iron diagram, in order to redissolve the pro-eutectoid cementite and thus to obtain recrystallization and grain-refining. This treatment was necessarily only partly successful, and I should like to ask whether the conditions of heat treatment for refining overheated high-carbon steels have been ascertained. Speaking of the &'Persistence of Solidificational Segregation " Professor Howe quotes an experiment made by Mr. Stead in which a bar of 1.2 per cent. carbon steel was immersed in a large mass of molten blast-furnace slag and allowed to cool with it. The steel was heated ; above the solidus (curve An on the carbon-iron diagram), but below the liquidus (curve AB). A drop of eutectic carbon-iron alloy, rich in carbon, had liquated out and hung below the bar. This agrees exactly with my own observations on the burning of steel, but my interpretation differs somewhat from that of Professor Howe. Professor Howe considers that the fusion of a part of the metal (rich in carbon) shows that the solidificational irregularities of composition had persisted through the rolling and heat treatment of the steel, as otherwise no part of the steel would have been sufficiently fusible to melt. It does not appear to me that such an explanation is necessary. A piece of steel represented in temperature and composition by any point within the area ABa will ultimately resolve itself into a solid phase and a liquid phase in equilibrium with each other. It may appear that if the steel were absolutely uniform no fusion could take place, but, the smallest nucleus of high-carbon, fusible alloy would ultimately bring about this separation into liquid and solid phases, by diffusion of the carbon from the solid to the liquid areas. A nucleus sufficient for the purpose might be provided by an area of pro-eutectoid cementite which had not become diffused during the

Jan 1, 1914

By H. J. Hand

STATISTICAL methods are becoming increasingly important for inter-preting routine reports, or for analyzing special test data in industrial plants, such as steel plants. They have already become practically a necessity to the plant metallurgist. A paper by Chancellor,1 written in 1933, gives many examples of the benefits the plant metallurgist can derive from the use of these methods. The present paper discusses applications of importance to many others who must analyze reports in the steel plant, as well as other examples of interest to metallurgists. Statistical Methods Logically Suited to Plant Problems.-Statistical methods are not new as a branch of mathematics. Until comparatively recently, however, practical applications were confined mainly to actuarial science, biology, and economics; fields in which an observed result is obviously influenced (and often determined) by a complicated set of vari-ables more or less constantly tending to affect it. As pointed out by Daeves, 2 a decade or more ago, problems in industry are basically similar to those in these other fields in that a given result is at least partly due to that chance combination of causes happening to be present at the time. When trying to do the same thing repeatedly, constant results are never attained; they vary about the desired result with more or less well defined mathematical regularity. Such a condition arises out of the great number of factors tending to affect the final result. If statistical methods are so valuable to the biologist or economist, why then should they not also be of great value to plant managers and engineers, and to all who must interpret reports from various sources in the industrial plant? Within the last few years, industry has become conscious of this situation, and the use of these methods has been rapidly expanding in such plants. ?

Jan 1, 1938

By Walter Herd

FOR the past eight years No. 2 mine of the Cumberland Railway & Coal Co., Springhill, Nova Scotia-a subsidiary of the Dominion Coal Co., Ltd.-has had an unenviable reputation for bumps. As the workings extended in certain directions under a greater cover, these bumps increased in severity and it became apparent that some change in the system of extraction was necessary if the mine was to continue to operate. In September, 1924, following several fatalities resulting from bumps, the Mines Department of Nova Scotia requested from the U. S.. Bureau of Mines the services of George S. Rice, Chief Mining Engineer of the Bureau, to report on the conditions then prevalent in No. 2 mine, Springhill. This request was promptly and courteously granted. Mr. Rice made a full investigation and a comprehensive and helpful report, which is embodied in the 1924 Annual Report of the Department of Public Works and Mines, Nova Scotia. Prior to 1925, the room and pillar method wasp employed and in January of that year (there being a cessation of work from March to August due to labor troubles) longwall retreating on the west side, on a limited scale, and in a small section on the east side of the mine was started. The major portion of the east side was not operated on this system till August, 1926, as there was developed a considerable area ready for pillar extraction between an arbitrary boundary and a point up to which bumps of any consequence had not been experienced. In the interval development work for longwall retreating below the 5900-ft. level was vigorously pushed. This longwall retreating system was suggested by Mr. Rice as a possible remedy and was heartily endorsed by the company officials. This paper describes the conditions and happenings subsequent to Mr. Rice's report and more especially the results with the longwall retreating system of mining under the peculiar circumstances pertaining to mining No. 2 Seam, Springhill, at depth, and records the conclusions which experience with several severe bumps under this mode of extraction would suggest. Except where necessary to make the paper intelligible as an entity any duplication of Mr. Rice's report will be avoided.

Jan 1, 1929