Search Documents

By H. M. Howe

I WISH to present to you a few thoughts on some of the phenomena and laws of iron smelting. Owing to the great complexity of the subject, to the great variety of points to be taken into consideration, many of which are very poorly understood, and to the meagreness and even conflictoriness of our information with regard to some of the most important laws which govern the subject, the fruits of such thoughts as I venture to offer you must be received as speculations, not as facts. Nevertheless, in discussing old phenomena from new standpoints, thus furnishing a metallurgical parallax, if I may say so, these theoretical speculations may have their value in helping to a clearer comprehension of the phenomena and laws we now know, and in suggesting new lines of inquiry. While an increase of height in blast furnaces is not always followed by increase in their power of production, experience proves that it tends to increase it; for while we have many cases of short furnaces producing more iron than longer ones, yet enormous productions, such as those of the Lucy and Isabella furnaces of Pittsburgh, and of the furnaces of Esch sur l'Alzette, in Luxembourg, have never been reached in short furnaces. We may safely infer that height is an element essential to great production, though of course not the only essential element, and that, in the case of high furnaces which are not capable of great production, some other essential element is wanting. Moreover, experience teaches that within limits increase of height tends to increase the producing power in a still higher ratio. Thus, in the Esch furnace, which is 19.8 meters (65 feet) high, 393 tonnes (or 387 gross tons) of 312 per cent. Ore

Jan 1, 1877

By Z. T. Bieniawski

The importance of understanding the phenomena associated with rock fracture has long been fully appreciated in rock mechanics. This is clearly apparent from the special attention paid to rock fracture in the comprehensive papers published within the past four years.l-5 These papers present a picture of how the knowledge of brittle fracture of rock was gradually enriched and also show that what was often taken for granted three or four years ago is no longer considered as valid today. The Griffith hypothesis,6 thought in the past to predict the strength of rock, is now known to be applicable to fracture initiation only. The knowledge of a failure criterion for fracture initiation is not sufficient, however, as after fracture initiation the rock is still a useful material even possessing increasing load-bearing ability. The importance of the fracture propagation process, subsequent to fracture initiation, is thus obvious. Yet, relatively little attention has so far been paid to brittle fracture propagation in rock. As it is now realized that understanding of this process is a prerequisite for practical rock mechanics applications, studies of propagation of brittle fracture in rock constitute an important aspect of rock mechanics research. It has been pointed out 4 that it is essential that the failure mechanism is fully understood before a failure criterion is postulated. Many failure criteria have been propounded in the past on the basis of theoretical reasoning alone and could not be verified by experimental evidence. Recently, a hypothesis for the mechanism of brittle fracture of rock was propounded, 4 describing the events taking place in the rock from the initial application of gradually increased load to complete disintegration of the material.

Jan 1, 1972

By Leonard B. Lipson

Boyer, Morgan and Muskat,' with improvements by Morgan, McDowell, and Doty,l and Laird and Putnam,' have described a scheme for the determination of fluid saturatic in porous media by measuring the x-ray linear absorbing power of particular fluids in the media. This method is one of several which depend on the linear absorbing power of the fluids in the porous medium. Other examples of linear absorption methods involve measurement of dielectric constant, gamma ray absorption, and ultrasonic attenuation. It is the purpose of this note to demonstrate by theortical considerations that the absorption versus saturation curve for a linear absorption method is not necessarily a single valued function of the saturation. Such non-unique behavior must be considered and evaluated before suitable saturation determinations can be made by a linear absorption method. To illustrate the discussion, examples will be given only for the simplest cases of combinations of two different dielectrics. The dielectric constant method was chosen for illustration because it was thought to demonstrate most graphically the point in question. According to Argue and Maass,4 the resultant dielectric constant of a combination of two different dielectrics depends on the orientation of the dielectrics in the electric field of the test condenser used to measure the dielectric constant. One ease involves alternate slabs of dielectrics E1 and E2 perpendicular to the electric field of the test condenser, as shown in Fig. 1A. For this case: l/'E, = A/E, + B/E,.......(1) where E,,, is the dielectric constant of the combination, A is the ratio of the path length through dielectric E, to the distance between the plates of the condenser (assuming the dielectrics have the same cross sectional area as the condenser), and B is the ratio of the path length through dielectric E2 to the distance between the plates of the condenser. It will be noted that the constants A and B are numerically equal to the fractional "saturation" of the region between the test plates of the condenser by the two dielectrics E1 and E2, respectively. Another case involves alternate columns of the two dielectrics parallel to the electric field and forming a continuous path between the condenser plates, as shown in Fig. 1B. For this case: E., = AE1 + BE2.........(2) where E., is the dielectric constant of the combination, A is the ratio of the cross sectional area of dielectric E, to the cross sectional area of the condenser plates (assuming the lengths of the dielectrics equal the distance between the condenser plates) and B is the ratio of the cross sectional area of dielectric E2 to the cross sectional area of the condenser plates. As before the constants A and B are the effective "saturation" of the condenser by the two dielectrics. Still another case is described by Lichtenecker5 where dielectric E2 is shown in the form of small particles distributed at random in dielectric E1. This is shown in Fig. 1C. For this case: log Em = A log E1 + B log E2.....(3) where Em is the dielectric constant of the combination. A is the ratio of the volume of dielectric E1 to the volume of the condenser, i.e., the effective "saturation" of the condenser by dielectric E,. B is the ratio of the volume of dielectric E2 to the volume of the condenser, i.e., "saturation" of dielectric El. Equations (l), (2) and (3) are plotted in Fig. 2 for E1 = 2.5 (oil) and E2 = 80 (water). Equations (1) and (2) may he thought of as representing the limiting cases of the configuration of two fluids which might be expected to exist in a porous medium. Equation (3),

Jan 1, 1951

By Leonard B. Lipson

Boyer, Morgan and Muskat,' with improvements by Morgan, McDowell, and Doty,l and Laird and Putnam,' have described a scheme for the determination of fluid saturatic in porous media by measuring the x-ray linear absorbing power of particular fluids in the media. This method is one of several which depend on the linear absorbing power of the fluids in the porous medium. Other examples of linear absorption methods involve measurement of dielectric constant, gamma ray absorption, and ultrasonic attenuation. It is the purpose of this note to demonstrate by theortical considerations that the absorption versus saturation curve for a linear absorption method is not necessarily a single valued function of the saturation. Such non-unique behavior must be considered and evaluated before suitable saturation determinations can be made by a linear absorption method. To illustrate the discussion, examples will be given only for the simplest cases of combinations of two different dielectrics. The dielectric constant method was chosen for illustration because it was thought to demonstrate most graphically the point in question. According to Argue and Maass,4 the resultant dielectric constant of a combination of two different dielectrics depends on the orientation of the dielectrics in the electric field of the test condenser used to measure the dielectric constant. One ease involves alternate slabs of dielectrics E1 and E2 perpendicular to the electric field of the test condenser, as shown in Fig. 1A. For this case: l/'E, = A/E, + B/E,.......(1) where E,,, is the dielectric constant of the combination, A is the ratio of the path length through dielectric E, to the distance between the plates of the condenser (assuming the dielectrics have the same cross sectional area as the condenser), and B is the ratio of the path length through dielectric E2 to the distance between the plates of the condenser. It will be noted that the constants A and B are numerically equal to the fractional "saturation" of the region between the test plates of the condenser by the two dielectrics E1 and E2, respectively. Another case involves alternate columns of the two dielectrics parallel to the electric field and forming a continuous path between the condenser plates, as shown in Fig. 1B. For this case: E., = AE1 + BE2.........(2) where E., is the dielectric constant of the combination, A is the ratio of the cross sectional area of dielectric E, to the cross sectional area of the condenser plates (assuming the lengths of the dielectrics equal the distance between the condenser plates) and B is the ratio of the cross sectional area of dielectric E2 to the cross sectional area of the condenser plates. As before the constants A and B are the effective "saturation" of the condenser by the two dielectrics. Still another case is described by Lichtenecker5 where dielectric E2 is shown in the form of small particles distributed at random in dielectric E1. This is shown in Fig. 1C. For this case: log Em = A log E1 + B log E2.....(3) where Em is the dielectric constant of the combination. A is the ratio of the volume of dielectric E1 to the volume of the condenser, i.e., the effective "saturation" of the condenser by dielectric E,. B is the ratio of the volume of dielectric E2 to the volume of the condenser, i.e., "saturation" of dielectric El. Equations (l), (2) and (3) are plotted in Fig. 2 for E1 = 2.5 (oil) and E2 = 80 (water). Equations (1) and (2) may he thought of as representing the limiting cases of the configuration of two fluids which might be expected to exist in a porous medium. Equation (3),

Jan 1, 1951

By L. L. Newman

As soon as the Congress recognized the alarming rate at which our domestic oil resources were being depleted during the war, it took action to step up the rate of research and development which the Bureau of Mines had been conducting for several years on the production of synthetic liquid fuels from coals. Under Public Law 290, approved April 5, 1944, funds were authorized for the Bureau to proceed with research, development, design and construction of demonstration plants for the hydrogenation of coal, the synthesis of oil from carbon monoxide and hydrogen, and the distillation of oil from shale. During the latter part of 1944, when it became evident that the collapse of Germany was near, a Technical Oil Mission was organized to study the German techniques of synthetic oil production. Since the cost of hydrogen or synthesis gas is one of the major factors of expense in the operation of hydrogenation or synthesis gas processes, the Bureau of Mines considered it of prime importance to include on the mission gas engineers whose instructions were to examine closely the methods employed by the Germans in solving the problem of providing low-cost hydrogen or synthesis gas for their very extensive operations on synthetic liquid fuels. The Solid Fuels Mission and the Utilities Mission, as well as the Army and Navy Missions, also included teams for the study of German gas production. Although their objectives naturally differed from those of the Technical Oil Mission and from each other, it was recognized that there was considerable overlapping of their fields of investigation. Duplication of effort, however, was largely avoided through the close cooperation between the group leaders of these missions. For example, although I went to Europe as a member of the Technical Oil Mission, my first Gcrman assignment was actually made by Dr. Harry F. Yancey, leader of the Solid Fuels Mission— to investigate the brown-coal gasification methods in central Germany. The art of gasification in the United States and England, and to a large extent in the proximity of the coking-coal regions of Germany and the rest of continental Europe, depends essentially on two stages of operation; namely, carbonization and intermittent water-gas generation. As far as the United States is concerned, complete gasification in a single stage of operation is rarely practiced, except in gas-producer operations where the product is a relatively lean gas consumed close to the point of manufacture, and for water-gas production with anthracite as a generator fuel. Complete gasification of bituminous coal has been the subject of numerous investigations. Many relatively simple modifications of the water-gas generator have been tried to permit the direct gasification of low-cost bituminous coal instead of high-cost coke and anthracite for the production of water gas. Although varying degrees of Success have been achieved and the water gas produced generally has been higher in

Jan 1, 1947

By L. L. Newman

As soon as the Congress recognized the alarming rate at which our domestic oil resources were being depleted during the war, it took action to step up the rate of research and development which the Bureau of Mines had been conducting for several years on the production of synthetic liquid fuels from coals. Under Public Law 290, approved April 5, 1944, funds were authorized for the Bureau to proceed with research, development, design and construction of demonstration plants for the hydrogenation of coal, the synthesis of oil from carbon monoxide and hydrogen, and the distillation of oil from shale. During the latter part of 1944, when it became evident that the collapse of Germany was near, a Technical Oil Mission was organized to study the German techniques of synthetic oil production. Since the cost of hydrogen or synthesis gas is one of the major factors of expense in the operation of hydrogenation or synthesis gas processes, the Bureau of Mines considered it of prime importance to include on the mission gas engineers whose instructions were to examine closely the methods employed by the Germans in solving the problem of providing low-cost hydrogen or synthesis gas for their very extensive operations on synthetic liquid fuels. The Solid Fuels Mission and the Utilities Mission, as well as the Army and Navy Missions, also included teams for the study of German gas production. Although their objectives naturally differed from those of the Technical Oil Mission and from each other, it was recognized that there was considerable overlapping of their fields of investigation. Duplication of effort, however, was largely avoided through the close cooperation between the group leaders of these missions. For example, although I went to Europe as a member of the Technical Oil Mission, my first Gcrman assignment was actually made by Dr. Harry F. Yancey, leader of the Solid Fuels Mission— to investigate the brown-coal gasification methods in central Germany. The art of gasification in the United States and England, and to a large extent in the proximity of the coking-coal regions of Germany and the rest of continental Europe, depends essentially on two stages of operation; namely, carbonization and intermittent water-gas generation. As far as the United States is concerned, complete gasification in a single stage of operation is rarely practiced, except in gas-producer operations where the product is a relatively lean gas consumed close to the point of manufacture, and for water-gas production with anthracite as a generator fuel. Complete gasification of bituminous coal has been the subject of numerous investigations. Many relatively simple modifications of the water-gas generator have been tried to permit the direct gasification of low-cost bituminous coal instead of high-cost coke and anthracite for the production of water gas. Although varying degrees of Success have been achieved and the water gas produced generally has been higher in

Jan 1, 1947

By Frank Fahrenwald

I. INTRODUCTORY METALLURGICAL research has discovered many an alloy possessing properties not combined in any single metal, and progress still consists chiefly in the investigation and utilization of alloys. In the case of iron, the demands of automobiles, high-speed machines and high-duty engines have led to the production of special iron alloys which will meet any reasonable specifications in that field. In like manner, the bronzes, brasses and other alloys of copper have been brought to remarkable perfection, and for nearly every industrial purpose some alloy has been found more suitable than the pure metal. Less complete success has attended the attempt to find substitutes for gold, platinum, and the other precious metals. Indeed, it is not likely that a material can be produced which will possess all the properties of any one of them; yet it is reasonable to hope that, for any given use, the properties required may, be found in some less expensive material. Thus, in incandescent electric lamps, the wire passing through the thick glass neck of the bulb was, until recently, almost universally made of platinum, for the single reason that no other known material, suitable as a conductor, had the same coefficient of expansion as glass. But a comparatively recent investigation of the iron-nickel series' has shown that alloys of those metals may be produced, the coefficient of expansion of which can be accurately controlled between that of iron or nickel and zero. Thus, in that particular industry, a substitute for platinum has been found. According to statistical reports, not only considerable quantities of gold and iridium, but also more than one-third of the annual supply of platinum, are used (and, in the nature of the case, irrevocably lost) by dentists. Platinum is thus employed in several forms. As a thin foil, it serves various purposes for which its high melting point, pliability, chemical resistance, and other properties-including the ease with which

Jan 1, 1916

By R. J. Blackwell, J. R. Rayne, J. R. Henderson, W. M. Terry, D. C. Lindley

This paper presents the results of a laboratory investigation of the efficiency of water-solvent mixtures in recovery of oil. These mixtures may have the high displacement efficiencies characteristic of solvent floods and the high sweep efficiencies characteristic of water floods. Thus, the water-solvent process may increase the number of reservoirs in which a miscible-type displacement can be used profitably. The experiments on the use of water-solvent mixtures for recovery of oil were conducted to find the general applicability of the process. These studies demonstrated that, in flowing through sands, water and solvent segregated into a solvent layer on the top and a water layer on the bottom rather than flowing through the sands as a uniform mixture. Calculations based on the simultaneous flow of the water and solvent in layers were used to predict the effective mobility of the mixtures and the optimum operation of the process in steeply dipping, homogeneous reservoirs. As most reservoirs are not suited for the operation of the process under ideal conditions, experimental studies were conducted with sand-packed models scaled to represent more realistic reservoirs. These studies included the effects on recovery of oil of rate of injection, viscosity of oil, variations of permeablity within a formation and variations in water-solvent ratio. For the range of con-ditions studied, higher recoveries of oil were obtained with water-solvent mixtures than with water or practical volumes of solvent alone. INTRODUCTION A group of intriguing—because of their great possibilities—new oil recovery methods at the disposal of the petroleum engineer are the miscible displacement processes. These processes (high-pressure gas drive, en-riched-gas drive and LPG bank driven by methane) displace all of the oil from the portions of the reservoir swept by the injection fluid. The key question confronting the engineer applying one of these techniques to a particular reservoir is, "What fraction of the reservoir can be swept by injection of a practical volume of solvent?"." Intensive laboratory studies have been made during the past several years in seeking answers to the question of the sweep efficiencies which can be expected in solvent floods.' - These studies provided the answer that low-viscosity, low-density solvents channel and by-pass oil in sands with no dip. In horizontal sands, solvent flooding becomes less efficient as the viscosity of the oil increases, the recovery of oil at solvent breakthrough decreases and larger volumes of solvent are required to achieve a given recovery. More efficient displacement of oil by solvent is observed under certain conditions in sands with dip.".' If the permeability and dip of the sand are sufficiently high, gravity segregation of low-density solvent injected updip can prevent channeling. At rates of depletion below a critical rate,"." no channeling occurs. Unfortunately, in many reservoirs, the critical rate is so low that production of oil at rates below this rate is not economically attractive. And at rates over four times the critical rate, channeling is almost as severe in sands with dip as in horizontal sands. These findings pointed out that, for solvent floods to be generally applicable in recovering oil from all types of reservoirs, new methods of improving their sweep efficiencies are needed. Simultaneous injection of water with the miscible fluid was suggested by Caudle and Dyes7 as a method for improving sweep efficiencies. They theorize that water flowing with the solvent would decrease the effective mobility of the solvent and cause it to contact more oil sand. If, indeed, the water and solvent flowed as a uniform mixture, the process should have the advantages of the high displacement efficiencies characteristic of miscible floods and the high sweep efficiencies of water floods. Thus, the method (at least in theory) would greatly increase the number of reservoirs in which miscible-type displacements would be feasible. A research program was conducted to probe the technical feasibility of the water-solvent process. It

By Brooks J. Klimley, Daniel M. Higgins, Grover R. Castle

Measuring The Economic Viability Of Resource Projects (A Western Surface Coal Project) The bankers approach to the analysis of a new "green fields" mining project is similar but different from the approach that the pining company might take. The purpose of this paper shall be to discuss the techniques that are used by mining companies and bankers as they try to measure the economic viability of mining projects. The analysis of these new projects (by both the mining companies and the banker) is based on a projected revenue stream and not on historical earnings or past perfomance because these projects are start up situations with no history to look to. The starting point in the analysis of these projections is the choice of the assumptions to be used in preparing these projections. After the assumptions have been determined and the projections are prepared then the projections are submitted to various tests in order to determine whether the project measures up to previously agreed upon minimum standards. In order to illustrate the analytical procedures used in evaluating a mineral project the writer has constructed a hypothetical case involving the development of a western surface coal mine (Property). The basic data in connection with this hypothetical new project is described in the next section of this paper. After the Description of the Project is a section which shows the type of analysis that a mining company might prepare in order to approach a bank for a loan and the final section illustrates the type of analysis that a bank might prepare in evaluating this loan request. Description Of The Project or Basic Data In Connection With Undeveloped Western Surface Coal Property An independent mining/geological Consultant's report has been completed on the Property which confirms that the Property contains 175 million tons of economically recoverable coal subdivided into the following reserve categories in accordance with U.S. Bureau of Mines and U.S. Geological Survey definitions: Measured or Proven 90,000,000 Indicated or Probable 50,000,000 Inferred or Possible 35,000,000 The owners of the reserves have chosen to drill up those reserves that are nearest to the subcrop and have not spent as much time on those portions of the Property which are on the fringes of the deposit where the overburden is thicker because the stripping ratio and hence the operating costs and capital requirements are higher down dip. The proven reserves are based on an average thickness of 80 feet, of which a mining recovery of 90% is projected. The overburden thickness varies from 0' to 280' with an average thickness of 127'. The overburden consists mainly of scoria, sandstone, gravel, shale and silty clay. 134 holes were cored (and analysis done on five foot increments) in the measured reserve on the following spacing: 100 foot centers to define the burn line; 1,320 foot centers to define the early mining areas; 2,640 foot centers to identify the later mining areas.

Jan 1, 1985

By John S. Johnson

The purpose of this article is to describe several types of borehole lining in common use, and especially to offer a relatively new means of reducing the expense of maintaining boreholes where they are subjected to corrosive action of water flowing either inside or outside of their casing. In the Anthracite region of Pennsylvania, boreholes are used for many purposes, the principal ones being: openings between the surface and underground workings through which are passed steam, water and compressed-air lines, ropeways from surface hoists to underground rope haulages, conduits for electric power and signal lines, water-discharge lines from underground pumping stations, and inlets to mine workings for flushing material. Linings for Boreholes The inadequacy of steel pipe for use in boreholes has long been recognized. Various substitute materials have been tried, including screw-joint cast-iron pipe (Fig. I). Cast-iron pipe, while very effective as a discharge line for acid water (mine water) being pumped to the surface, is not so effective when serving as a conduit for silt and crushed rock being flushed underground for filling mine voids. Terra cotta pipe (Fig. 2) has been used in boreholes, and lasts a long time if the glazed inner surface of the pipe remains intact. Its installation in a borehole is very difficult and is recommended only where it is certain that there will be no subsidence of the surrounding territory. Accessibility in order properly to join each section of the pipe is essential to a satisfactory job. In large water holes, where it is possible to lower a man into the hole for sealing the joints of the pipe, glazed terra cotta pipe has been used successfully for delivering mine water from pumps in the mines. For large holes used for flushing refuse into mine workings where the surface wash is shallow, standard paving brick have been used to form a tube through the wash to the bedrock. These brick are laid radially, backed by common brick and cobbles laid in cement. It is obvious that the shaft through the wash must be large enough to permit a man to work in it. The flushing material is carried through bare rock from the juncture at bedrock to the openings underground. This plan has been used particularly where a cast-iron surface line is laid upon the surface to carry the flushing material from the breaker to the hole, and down the hole continuously, with no opening to the air at the top of the hole, thereby eliminating the necessity of an attendant at this point (Fig. 3). Another similar type of borehole lining is constructed of hexagonal pieces of vitrified brick (Fig. 4). This type requires a steel drive pipe through the surface wash large enough to provide a finished tube of the desired size surrounded by a brick wall about 4 in. thick. The special bricks are laid in cement, six to a circle, around a lubricated pipe used as a form, and lowered in sections inside the large drive pipe; the bottom section is seated in a socket drilled in the solid rock, having the same inside

Jan 1, 1942

By John S. Johnson

The purpose of this article is to describe several types of borehole lining in common use, and especially to offer a relatively new means of reducing the expense of maintaining boreholes where they are subjected to corrosive action of water flowing either inside or outside of their casing. In the Anthracite region of Pennsylvania, boreholes are used for many purposes, the principal ones being: openings between the surface and underground workings through which are passed steam, water and compressed-air lines, ropeways from surface hoists to underground rope haulages, conduits for electric power and signal lines, water-discharge lines from underground pumping stations, and inlets to mine workings for flushing material. Linings for Boreholes The inadequacy of steel pipe for use in boreholes has long been recognized. Various substitute materials have been tried, including screw-joint cast-iron pipe (Fig. I). Cast-iron pipe, while very effective as a discharge line for acid water (mine water) being pumped to the surface, is not so effective when serving as a conduit for silt and crushed rock being flushed underground for filling mine voids. Terra cotta pipe (Fig. 2) has been used in boreholes, and lasts a long time if the glazed inner surface of the pipe remains intact. Its installation in a borehole is very difficult and is recommended only where it is certain that there will be no subsidence of the surrounding territory. Accessibility in order properly to join each section of the pipe is essential to a satisfactory job. In large water holes, where it is possible to lower a man into the hole for sealing the joints of the pipe, glazed terra cotta pipe has been used successfully for delivering mine water from pumps in the mines. For large holes used for flushing refuse into mine workings where the surface wash is shallow, standard paving brick have been used to form a tube through the wash to the bedrock. These brick are laid radially, backed by common brick and cobbles laid in cement. It is obvious that the shaft through the wash must be large enough to permit a man to work in it. The flushing material is carried through bare rock from the juncture at bedrock to the openings underground. This plan has been used particularly where a cast-iron surface line is laid upon the surface to carry the flushing material from the breaker to the hole, and down the hole continuously, with no opening to the air at the top of the hole, thereby eliminating the necessity of an attendant at this point (Fig. 3). Another similar type of borehole lining is constructed of hexagonal pieces of vitrified brick (Fig. 4). This type requires a steel drive pipe through the surface wash large enough to provide a finished tube of the desired size surrounded by a brick wall about 4 in. thick. The special bricks are laid in cement, six to a circle, around a lubricated pipe used as a form, and lowered in sections inside the large drive pipe; the bottom section is seated in a socket drilled in the solid rock, having the same inside

Jan 1, 1942

By B. Trentini

In the spectacular development of pure oxygen steel-making, the process using the vertical lance converter LD, is at the present time the most widely employed. Proper control of slag composition during the steel-making process appears to be essential in achieving satisfactory blowing from both the metallic yield and metallurgical points of view. The paper illustrates the primary importance of the presence of a large quantity of metal droplets in the slag during the process. In the case of both phosphorus and hematite pig iron, it can be deduced from the phase diagrams and confirmed by experimentation that nonhomogeneous slags are one of the causes of slag overflowing during the blow. The problem is however a complex one and further physicochemical studies appear necessary. Finally, the new continuous steelmakingprocess developed by IRSID is described. PEOPLE who knew Henri Marion Howe have said that he took great pleasure in speculating on the future of metallurgical processes. It is therefore not inappropriate to devote, in his memory, some description and discussion to processes unknown to the world of his time, in particular oxygen steelmaking and continuous steelmaking. The first industrial application to steelmaking of tonnage oxygen produced by air liquefaction was made in Germany just before the war and consisted in enriching the air blown through the bottom of a basic Begsemer converter in order to melt a higher proportion of scrap and to produce steels with lower nitrogen content than is achieved with conventional practice. While this process was being developed after the war, mostly in Western Europe, steelmakers were becoming increasingly familiar with the technique of blowing pure oxygen from the top, first by means of consumable steel pipes, with or without refractory shielding, and later by water-cooled lances, designed for the purpose and affording longer life. The field was then open for the wide use of pure oxygen in steelmaking, either in existing processes such as open-hearth or electric furnace, or in new processes. These new processes can be broadly classified according to the category of furnace employed. In the case of the vertical converter taken as the first category, bottom-blowing of pure oxygen causes extremely rapid wear of the refractory tuyeres, and although various expedients have been tried to overcome this drawback (such as mixing oxygen with CO2 or H2O or using high pressure oxygen), they have had to be abandoned. The solution for vertical converters has been found in top-blowing with a vertical water-cooled lance; this is known as the LD process or basic oxygen converter process.

Jan 1, 1969

By Stephen G. Dardaganian

Pore volume compresibilitieu measured in the laborutory on core .samples are reported for typical reservoir .sarrrl.rtorres at reservoir pressure. These cornpressibilities ore different for each reseriloir sample and cannot be correlated to porosity. The compressihilities are a1so functions of presslire. In recent years several authors have pointed out the importance of including pore volume compressibility of the reservoir rock in certain reservoir engineering calculations. Hall' showed that in calculating the hydrocarbon volume of an undersaturated reservoir from the production per unit change in reservoir pressure, the neglect of rock compressibility could, in the extreme case of low porosity rock, lead to results in error by a factor of two. Hawkinsl' and Hobson and Mrosovsky showed that both rock and interstitial water compressibilities must be included to achieve satisfactory accuracy in this calculation. Although rock compressibility is an important reservoir property in these calculations, very few data are available. Hall' made compressibility measurements on a few samples in a small pressure range. No other direct pore volume compressibility measurements have been reported. Geertsma' discussed the elasticity of reservoir rock but did not present any new data. In this paper, rock compressibilities suitable for reservoir calculations are reported for a variety of sandstones typical of U. S. reservoirs. The measurements were made through a range of pressures which is also typical of reservoirs. EXPERIMENTAL PROCEDURE Plugs 1 in. in diameter and 2- to 3-in. long were diamond drilled, 14 from cores from seven oil-bearing or potentially oil-bearing sandstone, one from a quarried sandstone, and another from a shallow, oil-free, pure orthoquartzite. The plugs were extracted in toluene, vacuum dried, and then weighed. The plugs were then saturated with kerosene and reweighed. This gave pore volume. They were then again extracted in toluene. vacuum dried, and jacketed in 0.004-in. thick copper foil. A short length of -in high pressure tubing led from the jacket. The jacketed sample was then saturated with kerosene and placed in the hydraulic pressure cell as shown in Fig. 1. Movement of the mercury slug showed the change in pore volume of the sample under a given pressure change. Temperature was about 72" F for all measurements. Before taking any measurements, the external pressure on the sample was raised to 10,000 psig and kept there for several hours. This formed the thin copper jacket around the plug. 7-he pressure was then removed and the sample left at least overnight, during which time it recovered its original pore volume. An external pressure of 12,000 psig was then applied and held constant. The change in pore volume was noted as the internal pressure was raised in 1,000 psig increments to 10,000 psig. The internal pressure was then reduced to zero, again noting pore volume changes,

By A. J. Weinig

The Liberty Bell cyanide precipitate is unique in that it is apt to vary widely in composition in the course of very short periods of time, and a method of refining and melting that would prove highly satisfactory at one cleanup would yield7almost a hopeless "mess" at a second. Table I gives a general conception of the wide range in grade and composition of those raw precipitates. It is evident that no one standard flux could be expected to produce a high-grade bullion with such a widely variable precipitate, and that any method of treatment with acid requires most careful consideration. Refining by Acids Naturally, our first efforts to improve our precipitates were directed along the lines of acid treatment. Table II embodies the results of careful sampling and analysis of one cleanup at the time when wet refining reached its maximum development at this mill. We have now discarded all methods of wet refining, successfully replacing them by a more scientific method of flux calculation described herein, but it is believed that a general description of this wet refining is warranted as it throws some interesting side lights on acid refining in general. Table I.—Range of Composition of Raw Precipitates Per Cent. Gold and silver.................................... 25.0 to 75 Zinc.............................................. 18.0to 30 Lead............................................. 0.5 to 52 Copper........................................... 0.5 to 20 Silica............................................ 1.0 to 5 Calcium oxide...................................... 4.0 to 8 Sulphur.......................................... 0.5 to 8 Column A gives the analysis of the raw precipitate; column B, that of the precipitate after heating with steam, with frequent addition of hydrochloric acid until a point was reached where the batch had a strong tend-

Jan 1, 1917

By E. P. Abrahamson, S. L. Lopata

A general relalionship between the amount of glide shear (due to slip) and the macroscopic shape change has been developed. Since the deformation can be large, finite strain analysis is employed. In this treatnzent, the shape change is expressed by a deforlnation gradient matrix, F - [axi/aXj/ where X and x refer lo the initial and final positions of a particle. This matrix is readily evaluated in termas of the amounl of glide shear, a , and the direction cosines of the slip-plane normal and the slip direction for a single active slip systena. In the case of deforma tion from slip on several systems, the product F(a) of the several deformation gradient matrices is first calculated. Then, by assuming that the final configuration is reached by a long series of small shears of magnitude a, occurring more or less alternately in the several slip sys- IN problems of crystal plasticity, it is often necessary to relate the amount of glide in the operating slip systems to the macroscopic strain components. This relationship is relatively simple when only small strains are considered. In this case the separate strain contributions from several slip systems are additive. Such a procedure is incorrect in the case of large plastic deformation. To the authors' knowledge, no general treatment of the latter problem has appeared in the literature. In specific instances, Mark, Polanyi, and schmid3 have derived the relationship between glide and axial elongation during tensile pulling of a single crystal when only one slip system is active. A similar relationship for duplex slip was worked out by v. Göler and Sachs.4 Taylor and Elam1 have also studied in detail problems of large plastic deformation. Due to uncertainties as to the slip systems at the time, ! terns, the final deformation gradient matrix can be obtained. Mathematically, the problem is reduced to finding the limit of F(aN as N — m while a — 0 in such a way that the Product Na = a finite conslant designatzng the accumulated amount of shear. It turns out that this limit is simply eafF1, where F, is the matrix whose elements are the coefficients of a in the F(a) twatrzx. Application is made of the present treatment to a fcc crystal of Permalloy compressed on the (110) plane and contrained to elongate in the [112] directzon. In addition, it is shown that one rnay readily obtain from the general analyszs the well-known formulas relating elongation, amount of glide shear, and amount of lattice rotation for crystals deforming by single and double slip under tension. however, they were mainly concerned with proving that slip occurs on {111}(110) systems in fcc metals. The present general treatment arose out of recent investigations of magnetic anisotropy in cold-worked Fe-Ni alloys6 as well as some related problems in strength anisotropy of single crystals.' Detailed application of the general analysis will be provided in the case of a Permalloy single crystal compressed on the (110) plane and constrained to elongate only in the [112] direction. It will be seen that, as expected, the small strain approximation leads to significant errors after moderate straining. It will also be shown that the present general treatment yields the formulas of Mark et al. and of v. Goler and Sachs in those specific cases. GENERAL CONSIDERATIONS Consider a homogeneous deformation in which a material point initially at moves to (xl,xz,x3), both positions being referred to the same set of Cartesian axes. Such a deformation can be

Jan 1, 1967

By John W. Cahn

Tile avevage value of the mean curvature of surfaces in a specimen can be precisely delermined by sitrlple measurements performed on random sections or on 1 vojectiotzs of these surfaces. For surjaces enclosing particles, the quanlity is sllown to be velated to the probable tlurrrhev ot particles intevcepted by a random platne and, under certain conditions, to the perimeter of their Projected image and to the increuse in surjace area when the particles grow. Many of the velalionsl~ips are valid for any shape or size of the particles. THE recent growth of the field of stereology or quantitative microscopy is largely the result of the discovery of a limited number of rigorously defined geometrical parameters that can be precisely measured on random sections or projections of a structure without assumption about particle shape.' Such parameters have been the volume fraction and surface area and line length in a unit volume. The present paper introduces the average of the mean curvature of surfaces in a volume, and shows that it can be rigorously measured by counting methods alone. AVERAGE CURVATURE ON A PLANE Consider a curve y = v (x) on the xy plane. The curvature Kp in the plane at any point is given by Kp = (dZy/dx2)/[1 + (dy/dx)2]3/2. The average curvature along the curve may be defined as Kp = (1/L) fKpdl |1] where dl = [(dx)' + {dy)2]1/2 is the length of an element of the curve and .(dl = L is the total length of the curve. The integral on the right-hand side of Eq. [l] will be called the total curvature, It is dimensionless and readily evaluated by substituting d = arctan (dy/dx) to give ah which is the change in direction of the tangents to the ends of the curve, Fig. 1. Hence, Kp = (1/L)(?h) [2] It can also be seen that Eq. [2] is applicable in the limit of sharp corners. Even though the curvature is infinite at a corner, f Kpdl remains integrable and equal to the change of angle. The signs of the quantities Kp and dl are arbitrary and, if the areas adjoining the curve are equivalent, there seems to be no compelling reason to fix the signs. For a closed curve, however, it becomes worthwhile to use the signs to distinguish among different types of areas or phases enclosed. For such a closed curve AO = t2r and As a convention, we shall take the direction of the integration along the curve in such a way that the area or phase under consideration (henceforth called a) is kept to the left side of the curve, Fig. 1. Then Kp is positive where the curve is concave and negative where the curve is convex. For a closed curve Ad - +2n if the curve encloses a, and Ad = —2n if the curve is surrounded by a. PLANAR SECTIONS OF THREE-DIMENSIONAL STRUCTURE OF ISOLATED a PARTICLES Consider next a planar section of a microstructure containing particles of a in a matrix. We place no restriction on shape of connectedness of these particles, and begin by considering the curvature of only the boundary between a particles and matrix' Clumps of contiguous a particles are then treated as a single a particle. The two-dimensional section will show in a unit area na simple closed curves enclosing a particles and nh closed curves of holes, in-

Jan 1, 1968

By M. C. Flemings, T. Z. Kattamis

Dendrite morphology and grain size were studied in bulk samples of iron and nickel base alloys under-cooled up to 300°C. In the alloys studied, dendrite morphology gradually changes with increasing undercooling from the usual dendritic structure to a structure composed of cylindrical dendrite arms. At a critical undercooling of approximately 170°C in these alloys there is an abrupt transition to a fine-grained structure of spherical morphology. Final dendrite-arnz spacing of melts nucleated at less than the critical undercooling decreases with increasing undercooling and with decreasing distance from a chilled surface. Grain size of melts nucleated at greater than the critical undercooling decreases similarly with these factors. It is concluded that structure coarsening, with reduction of surface area as driving force, is the principal mechanism determining final dendrite-arm spacing in melts nucleated at small undercoolings and grain site in melts nucleated at large undercoolings. IN solidification of highly undercooled melts, nuclea-tion and growth of the solid is accompanied by a rapid release of latent heat of fusion. The heat release is sufficiently rapid in bulk specimens that it takes place essentially adiabatically with respect to the surroundings; hence the specimen heats up ("recalesces") to some maximum recalescence temperature. For bulk liquid metals and alloys, a simple thermal balance shows the undercoolings obtainable in bulk samples are not sufficient to lower the maximum recalescence temperature below the equilibrium solidus temperature. Hence, some liquid always remains at the end of recalescence; this liquid must solidify by rejection of heat to the surroundings. Metals, including iron and nickel base alloys, normally freeze with only a few degrees of undercooling. In general, nucleation begins on impurity particles present in the metal, at a "heterogeneous nucleation temperature" that is quite close to the equilibrium liquidus temperature. Very small droplets of metal can be undercooled considerably before nucleation occurs,1-4 presumably because subdivision of the liquid reduces the probability of solid impurity in a given droplet. Following early work on metal droplets,' a series of studies has shown that it is possible, without great difficulty, to undercool bulk samples of many metals and alloys. Undercoolings obtainable are approximately two tenths of the melting point for nickel, iron, copper, and other metals and alloys.5-9 Specimen sizes have generally been in the range of 50 to 500 g. Studies on undercooling to date have been concerned primarily with techniques of undercooling and with nucleation and growth kinetics. Only limited consideration has been given to dendrite morphology in under- cooled alloys. One such study, in bulk Cu-Ni alloy,8 showed that at small undercoolings a typical dendritic structure was obtained. At undercoolings the order of 175°C the structure of a Cu-40 pct Ni alloy became "ray or starlike", and a dense network of subbound-aries appeared. At still larger degrees of undercooling, of the order of 250°C, the structure became more random and included an ensemble of globular forms. Comparable results were obtained by walker10 on Cu-Ni alloys, and by Kamenetskaya et al.11 in research on Cu-Ni, Sb-Bi, Fe-Ni, and Fe-Cr alloys. In this work, study was made of the processing parameters influencing dendrite morphology and grain size in undercooled alloy melts. Experiments were specifically designed to show the effects of coarsening ("ripening") during solidification on final casting morphology. EXPERIMENTAL PROCEDURE Apparatus used was patterned after that of Walker,10 Fig. l(a). Melting was by induction under reduced pressure of helium. Two different types of crucible materials were used; there was no difficulty in obtaining substantial undercooling in both types of materials. Alumina crucibles were used for the bulk of the runs made, with a glass coating separating the metal from the crucible walls. Other runs were made using fused silica crucibles with or without slag coating. A graphite susceptor was employed around the crucible to aid in melting and to reduce melt stirring. The major portion of the experimental work was on

Jan 1, 1967

By J. D. Verhoeven

The effectiue distriblltion coefficient has been Measured in a series of vertical, normal freezing experirtzents with large current densities passing through the solid-liquid interface. The results indicate that the effect of the current on solute redistribution is due to electvotransport in the liquid. The high currents produced extensive mixing in the liquid which was considerably reduced by solidifying in small lubing. Analysis of the convection indicates that it probably vesulls from a horizontal temperature gradient produced by the Joule heating- of the electvic crirver~t. Due to the strong dependence of this convection upon the specimen radius, it is conclnded that only for specit~ens with radii of less than somewhere between 1 and 2 mm wilt electric field freezing be getlerally effec-tire at enhancing the purification of zone-melting experittierats in loe-melting alloys. Experiments on 0.8-mm lubes illustrate some interesting potential applications of this techniqne as a means of solute control on smcrll specimens. In a number of papers published within the last few years'-4 it has been found that passage of large dc currents through the solid-liquid interface of a freezing alloy produces a change in the solute redistribution accompanying the solidification. It had been predicted theoretically by Hucke et al.s and by Pfann and Wagner that such an effect would occur as the result of electrotransport within the liquid boundary layer at the solid-liquid interface. These authors independently derived the following relation between the effective distribution coefficient and the variables of the process: Where k0 is the equilibrium distribution coefficient, V is the mobility of the solute relative to the solvent, E is the electric field intensity, D is the solute diffusion coefficient, R is the rate of interface motion, and 6 is the boundary layer thickness. Both groups of authors show that this equation predicts the possibility of extending the purification ability of zone-melting experiments by the addition of an electric current. However, there are other effects in addition to electro-transport which could be produced by the high dc current and might, perhaps, invalidate the applicability of Eq. [I]. For example, high electric current might affect the interface reaction or perhaps the equilibrium distribution which was assumed to exist at the interface. It was the purpose of this work to determine the applicability of Eq. [I] by systematically investigating a simple system for which all of the necessary parameters were known. It was of particular interest for speculating on the potential usefulness of this technique to determine the maximum practical field intensities obtainable, and the effect of these high fields upon convective mixing in the liquid. The initial work in this study was published in a previous paper3 which will be referred to as I. In that work, a current density of 2000 amps per sq cm was used with specimen diameters of 5 mm. The results gave a qualitative confirmation of Eq. [I.], and also showed that a large amount of convective mixing was produced in the liquid by the current. The present study is an extension of that work to smaller specimen diameters and higher current densities. Two points were overlooked in I and will be emphasized here: a) the value of ko has not been well-established in the Sn-Bi system and b) the observed convection could be due to thermal convection produced from the Joule heating. EVALUATION OF k0 To evaluate Eq. [ I.] it is necessary to know the value of the equilibrium distribution coefficient, k,. Tn I the value of k, was taken as 0.3 from a published phase diagram.7 According to ansen' the best data on the phase boundaries of the Sn-Bi system are those of Davidson.5 The data of Davidson give a k, value ranging from 0.21 to 0.25 for the compositions studied in this work, or an average value of around 0.23. In a recent publication, Rigaud and Tougas'10 determined ko by means of a solidification technique. For an alloy of approximately the same composition as that used in this work they obtained a ko value of 0.39. Hence, there is considerable uncertainty in the value of ko and, consequently, a series of experiments were made to determine k, more accurately.

Jan 1, 1968

By George Sachs

I deeply appreciate the honor of being selected to deliver the twentieth Annual Lecture of the Institute of Metals Division. The subject of my paper is extremely involved and voluminous, therefore I shall discuss only some more recent experimental material and speculate somewhat on the physical and mechanical fundamentals of these changes. The flow and the rupture of a solid material are rather different phenomena. It is therefore surprising that up to a rather advanced stage in metallurgical science these two fundamental phenomena have been simultaneously treated and forced into the general conception of the "failure" of solid material. Only in this century, and particularly during the last 20 years, have the very different physical meanings of flow and rupture been clearly recognized. Several hundred of the more recent publications deal with these subjects.1 LAW OF SIMILARITY The basic values commonly considered responsible for the mechanical behavior of any material are the stresses. From this standpoint both a large and a small article made from the same homogeneous metal and of geometrically similar shapes should behave identically, i.e., they should deform geometrically in a similar manner, if subjected to the same stress values at corresponding points. This "law of similarity" was introduced about 60 years ago simultaneously by Barba2 and Kick3 and was derived from the classical theory of elasticity. As far as the plastic behavior of a metal is concerned, this rule appears to be valid. The conventional properties of large and small tension or compression test bars, machined from larger sections, are identical; while the force required to deform a section is proportional to its cross-sectional area and the work consumed in deforming geometrically similar articles in a geometrically similar manner is proportional to its volume. The general trend of the stress-strain diagram of a metal is independent of the section size (Fig. I). No exceptions from this rule are known. However, if the deformation of a metal is continued until rupture occurs, and the breaking stress or the work consumed is measured, a test bar of large cross section appears to fail before or at lower stresses than does one having a small cross section. Thus, the specific impact energy has been often found to decrease with increasing size of the test specimen, particularly for materials with a limited ductility.4 Another exception from the rule of similarity is offered by fatigue-strength values, which usually decrease with increasing section size. 5,6 The conclusion must be drawn from these experimental facts that the ductility of a homogeneous metal decreases with increas¬ing section size (Fig. x). This effect has been actually confirmed by Docherty,7 who observed that in static notch bending tests large specimens failed earlier and in a more brittle fashion than small specimens ma-

Jan 1, 1941

The following is an incomplete list of members and guests who called at Institute headquarters during the period Nov. 10, 1918 to Dec. 10, 1918. Arthur C. Adair, Camp Meade, Md. L. S. Mitchell, Montreal, Canada. Arthur K. Adams, Camp Humphreys, Va. T. E. Mitchell, San Francisco, Cal. Toner Antisell, Chevy Chase, Md. H. Mortimer-Lamb, Montreal, Canada. V. W. Aubel, New Castle, Pa. Edmund Newton, A. C. Black, El Paso, Tex. Paul T. Norton, Jr., Columbus Ohio. 0. F. Brinton, Baxter Spgs., Kans. Elmer W. Pehrson, San José, Cal. C. S. Corbett, Minneapolis, Minn. Joseph E. Pogue, Washington, D. C. W. M. Corse, Mansfield, Ohio. T. C. Roberts, E. Orange, N. J. G. C. Crossley, Toms River, N. J. D. R. Semmes, Richmond, Va. H. S. Emlaw, Grand Haven, Mich. H. L. Slosson, Jr., San Francisco, Cal. Rudolph Emmel, Boston, Mass. W. H. Staver, S. G. Garrett, U. S. N. R. F. A. L. Sweetser, Boston, Mass. Lt. Francis Geib, Denver, Colo. Lt. H. B. Taylor, Kansas City, Mo. Wm. E. Hubbard, Wichita Falls, Tex. Kirby Thomas, New York. Arthur Iddings, Wichita Falls, Tex. Benj. F. Tibby, Salt Lake City, U. Zay Jeffries, Cleveland, Ohio. J. L. Towne, Whitepine, Colo. S. J. Kidder, Mogollon, N. M. Chas. W. Tubby, St. Paul, Minn. Lt.-Col. W. H. Lanagan (Engrs.). A. G. Waite, Brookline, Mass. Major W. F. Lewis (Engrs.). Timothy D. Walsh, Denver, Colo. 0. M. Lewyn, Thomas Warner, Phoenix, Ariz. A. McClintock, DeKalb June., N. Y. J. P. B. Webster, London, England. Major Donald G. Miller, N. M. E. W. Westervelt, Los Angeles, Cal. C. E. LeN. Arnold, formerly with the Inspiration Cons. Copper Co. at Inspiration, Ariz., has accepted a position with the Consolidated Arizona Smelting Co. at Mayer, Ariz.

Jan 1, 1919