Search Documents

By J. F. Myers, F. M. Lewis

The paper reports the development of a large, slow speed ball mill closed circuited with a hvdro-scillator. This increased grinding efficiency 28 pct over conventional units. AS the title indicates, this is a progress report for the first year of experimental operation of a relatively large diameter, slow speed ball mill with 1-in. balls, with and without various classifiers, and including a hydroscillator. Several years ago the authors came to the conclusion that if any further progress were to be made in our flotation process, an understanding of the chemical and physical reactions and the control thereof, in the grinding circuit, was essential. It may be stated, at this point, that the preparation of a correct feed for the flotation process is still the number one objective of our grinding studies. This progress report deals with grinding "per se," and not with the chemical and physical reactions as the result of grinding. Prior to this time we had taken the naive position, that since grinding had been practiced by the industry for some fifty years or more, it had been well exploited and developed by a host of investigators. Consequently, we had given the matter only superficial attention. At the start of our study, we were aware of the fact that some difference in opinion existed, but we were not prepared for the controversial evidence that developed nor for the extent to which the experts differed in their viewpoints. There seemed nothing else to do but to tour the continent and decide for ourselves what was right and what was wrong, read all the published literature and visit with anyone who had ideas about the matter. This we did over the next few ensuing years. Since our study has met with some measure of success, we report, herewith, these data that ultimately they may be of help to other investigators. In 1944 it became necessary to increase our grinding capacity and at the same time to grind the sulphide portion a little finer. This provided the impetus to put our ideas into effect. As has been previously described, our grinding flowsheet at that time consisted of a 6x12 rod mill, followed by two 5x10 ft, and one 6x12 ft trunnion overflow ball mills, with conventional rake classifiers. Naturally, we first considered all the possibilities of altering or adding to the existing equipment. It became evident that if any appreciable increase in grinding efficiency could be obtained, it would pay to scrap the existing small mills and classifiers and install one big mill with adequate classification. Trying to determine just how much more efficient a big mill could be, in which were incorporated all

Jan 1, 1951

SUMPEARY OF CURRENT PRACTICES History The outcrop and surrounding area of Comincots Sullivan Mine was originally mined by small open cuts on surface and small open stopes underground to which shafts and adits were driven for access. When it was established that a commercial grade of ore was available, an adit was driven on the 4600 level (feet above sea level), and OM was extracted by larger scale open stoping leaving supporting pillars where necessary. After the depth of the ore body was proven to the 3900 level and an adit driven at this level, many miles of drifts, crosscuts, raises and sublevels were driven for the extraction of the ore above this level. Larger open stopea were extended from this development. The mining method was, and to a very limited degree still is, a benching method. Due to the strong hanging wall in this area of the mine, stopes with a width of 100 feet or more were opened. In 1931, because the orebody was proven to extend below the 3900 level, a winze was sunk from the 3900 level to the 3350 level. From this winze three intermediate levels were opened. Following a plan of development well in advance of production requirements, further sinking was done by winzes and eventually a large shaft was raised to surface. Prior to 1958 the 2850 level was bottom which since that time has been extended to the 2500 level. Open stopes were developed and mined as this area was opened up.

Jan 1, 1970

By S. D. Dahlgren

The plasticity of unalloyed P plutonium was studied by evaluating the strain-rate-hardening exponent, m, in the equation Values of m up to 0.33 and tensile elongations up to 680 pct were obtained for ß plutonium formed directly from the a phase. Casl bars that were cycled and tested had lower flow stresses and higher values for than uncycled bars , hut their total plastic elongations were not as great as expected because of premature failure at voids formed during cycling. Flow stresses were higher and m was lower (m = 0.15) for 9 plutonzutn formed from the y phase. ThE strain-rate-hardening exponent for plastic flow of p plutonium was determined as a function of strain rate, test temperature, and heat-treating history, and it was related to the rather large plastic elongation found previously for some plutonium tensile samples. Gardner and ~ann' obtained tensile elongations of up to 620 pct for P plutonium samples which had been completely transformed from the low-temperature a phase to the P phase before testing. Such a large percentage elongation is unusual for unalloyed metals or single-phase alloys.' The a phase is stable below approximately 112°C and (3 is stable between approximately 112" and 190"c.~ Both phases have mono-clinic structures. A temperature of 160°C is 0.58 of the effective absolute melting point, 475°C) of the p phase. The effective melting point is obtained by considering the enthalpy and entropy changes associated with the higher-temperature phase transformations and it is not the same as the experimental melting point of the highest-temperature allotrope of unalloyed plutonium. Nelson, Bowman, and Bierlein observed a striking difference between the ductility, as well as other mechanical properties, of p plutonium formed from the next higher-temperature phase (y) and the ductility of /3 plutonium formed from the a phase. The total elongation of /3 plutonium formed from the y phase was less than 5 pct. Earlier, the creep rate of 13 plutonium formed from the a phase was shown to be 200 to 500 times faster than the rate for 0 formed from y for the same test temperature and stress.

Jan 1, 1969

F. Lynwood Garrison, Philadelphia, Pa. (communication to the Secretary): I have been specially interested in Mr. Drake's valuable contribution to our knowledge of the Chinese coalareas, as I had occasion, about a year ago, to make a reconnoissance over some of the coal-fields in the Yangtse river valley. I noticed, as he appears to have done, certain peculiarities which may eventually prove to be characteristic of the Chinese coal-measures, at least in central and northern China. The most striking feature, perhaps, is the invariable proximity of the great granite masses to those coal-deposits which have an anthracite character. In common with all other anthracite areas elsewhere, the Chinese show evidences of profound stratigraphical disturbances. The sedimentary rocks are folded, faulted and dislocated in a manner similar to those of the Pennsylvania anthracite-regions. It would seem that the intrusive granite had much to do with converting the original bituminous into present anthracite. The action of the granite was probably direct as a conveyor of heat, and indirect as dynamic force in dislocating, overturning, and compressing the coal-measures. My stay in China was unfortunately cut short, so that I was unable to collect fossils, or to give this highly interesting and important subject more than passing attention. Cholnoky* and Richthofen are practically agreed that these granite eruptions took place during the Tertiary period—probably the Eocene. This profound tectonic movement has had a most important effect upon the geological conditions in central and northern China, and will be, I am sure, a potent factor in the economic development. Evidences of disturbances and metamorphism are very abundant in the anthracite-areas of the Yangtse valley. I noticed the coal in them, as did Mr. Drake in northern China, to be often flaky and " slickensided."

Jan 1, 1902

By Albert R. Ledoux

Discussion of the Paper of Albert R. Ledoux, read at the Atlantic City Meeting, February, 1904. ARTHUR JARMAN, Sydney, New South Wales, Australia' (communication to the Secretary*): Some remarks upon. Dr. Ledoux's interesting paper from one who has not visited America may, I hope, be of interest to members. It appears to me that there is considerable difference between the training of the American and of the British mining engineer. Not that the subjects are different, but rather in the way in which they are handled, the illustrations being, as far as possible, mining in character. Colloquial instruction is unknown in English curricula, but could be introduced with advantage. Students here assure me that an hour of conversation is of tar more use to them than an hour of the best lecturing. In England a school-year of 6 or 7 months would be considered very short indeed; but Americans do not consider it so, for the reason that the rest of the year is mostly spent in acquiring practical acquaintance with their subjects in works or in the field, and the shorter courses, when coupled with this large amount of outside expe¬rience, produce an essentially practical-minded engineer, who is also more of a business man; whereas the English system, though excellent from a scholastic point of view, produces the theoretical rather than the practical man. British schools are waking up, however, and the practical aspect of the engineer's training is receiving greater consideration. Once launched upon his career, the American engineer is immediately called upon to exercise his self-reliance and ingenuity, if he is to retain the confidence of his employers; but what can we say of English directors? In how many cases is the engineer allowed to guide the destinies of his company? Witness several recent cases of gross waste of money upon unsuitable plants, and the perpetuation of prehistoric methods of

Mar 1, 1905

By E. Hornbogen

The deformation mechanisms of a iron-phosphorus alloys were compared at 20oand —196°C. Alloying with phosphorus increases the resistance to slip, but has little effect on the resistance to twinning. The stress for onset of twinning is nearly independent of temperature, but there is an increasing tendency for cleavage along (112) twin boundaries with decreasing temperature and increasing phosphorus content. FIVE iron-phosphorus alloys and one high-purity iron (0.004 pct C, 0.004 pct N, 0.05 pct O) were vacuum melted and cast, then homogenized for 6 hr at 1100oC and water-quenched. Single crystals were cleaved from the coarse grains produced in this manner. The hardness was measured* on polished (100) surfaces of the crystals at 20" and -196°C. Laue back-reflection patterns indicated a deviation of not more than 3 deg from coincidence of the {100} plane with the surface. The deformation mechanisms were studied by relief effects on the polished surfaces. Yield points in compression (0.5 pct offset) were measured with polycrystalline material. At 20°C the addition of phosphorus to a iron leads to a change from slip to twinning as the main deformation mechanism, Figs. 1(a), (b). Between 2 and 4 at. pct P slip and twinning occur simultaneously. In alloys with more than 4 at. pct P twinning is the main deformation mechanism and slip was observed only in the neighborhood of twin intersections. All cracks at 20oC were on (100) planes, some initiated by twins.' From measurements made at-196oC, hardness and yield points of all the alloys were nearly constant and the same as the hardness of high phosphorus alloys that deformed by twinning at 20°C, Figs. 2 and 3. In the high-purity iron, plastic deformation at -196°C occurred by both slip and twinning, but deformation in the iron-phosphorus alloys appeared to be entirely by twinning. In the high phosphorus alloys a large number of cracks formed along the (112) twin boundaries and at intersections of twins, in addition to the (100) cleavage, Fig. 1(c). DISCUSSION In , iron, plastic deformation can occur either by slip or by twinning, depending upon composition,

Jan 1, 1961

THE CHAIRMAN.- This meeting is under the auspices of the American Institute of Mining and Metallurgical Engineers, and I think the germ of the idea originated in the steel business. Last year there was a meeting of prominent people in the steel industry with the idea of getting together and discussing practical phases of their business, so that everybody could contribute and from that there might be benefit derived for the industry. Several months ago when Mr. Bain was in Salt Lake City, he and Mr. Oldright asked me what I, as an individual, thought of it. From that originated this idea of having the copper people come together to discuss reverberatory smelting and all its phases. In starting out, it seemed the best plan to ask members what particular subjects they wished to discuss first; that is, the ones that would be considered more important. We asked Mr. Oldright, or suggested sometime ago that the meeting be postponed until May because May is a lovely month in Salt Lake. There are a number of attractive features around the city. We have a number of smelters here and I think that probably the most of the benefit will be derived from talking in an informal way and visiting the various plants around. the valley. At any rate, speaking as a resident of Salt Lake, I am glad to see all of you gentlemen here, and hope you have an interesting and instructive time. The tentative list of subjects for discussion at this conference is as follows: Construction Walls, etc. Walls, proper design and thickness of brick for various types of charging. Bottoms, construction of. Binding steel, correct weight and arrangement, where thrust of arch should be taken. Refractory materials, feasibility of using different material in various parts of the furnace. Water jackets, where applicable. Should bricks be used inside of same. Gas space, proper design for, height of roof above bath, etc. Roof Shape of Roof, in hot zone and elsewhere, longitudinally. Construction of roof, in various zones, around openings.

Jan 1, 1930

By H. R. Wheeler

CREATION of a "committee on promotion of student interest in coal mining" has an encouraging implication for the coal industry. It is indicative that mining men, both in the field and in the educational centers, realize that the problems of the industry require the best talent available. Young men are being invited into coal on the premise that it needs them, that it offers opportunity for creative work and the realization of their objectives. In initiating a movement which purports to meet the objectives of any young man who spends four or five years of his life in college, the industry does so with a full realization of its obligations.

Jan 1, 1940

The objective of the mission was basically to study the utilization of engineers and engineering technicians and their interrelationship in the Soviet Union. Beginning with their graduation from the engineering institutes and technicums, we hoped to learn how the graduates started out in industry, what their training on the job was, what sort of work they did, and how they worked themselves up within their profession. However, it turned out that, as our host was the Ministry of Higher and Secondary Education, most of our visits were to educational establishments. Our itinerary covered Moscow, Leningrad, Kharkov, Rostov, Baku, and Tashkent, with a side trip to Samarkand. In all, we visited 13 technical institutes, three technicums, and five industrial plants or enterprises, as they are called there. Our trip was one of only four weeks. Our observations were limited by the few cities and enterprises we were permitted to visit. Nevertheless, we did come back with some definite impressions and conclusions which we feel should be of interest to engineers, educators, and those concerned with the relative economic and technical power of the USSR and the U.S.

Jan 9, 1960

Time as a Factor in the Making and Treating of Steel. By John Johnston. (Howe Lecture) (T.P. 1478) Influence of Chromium and Molybdenum on Structure, Hardness and Decarburization of 0.35 Per Cent Carbon Steel. By R. F. Miller and R. F. Campbell. (T.P. 1345) Mechanical Properties of Iron-manganese Alloys. By F, M. Walters, Jr., I. R. Kramer and B. M. Loring. (T.P. 1369) The Instability of Low-expansion Iron-nickel-cobalt Alloys. By I. R. Kramer and F. M. Walters, Jr. (T.P. 1370) The S-curve of a Chromium-nickel Steel. By B. M. Loring. (T.P. 1383) A Magnetic Determination of the A3 Transformation Point in Iron. By B. A. Rogers and K. 0. Stamm. (T.P. 1388) Rapid Tension Tests Using Two-load Method. By A. V. de Forest, C. W. MacGregor and A. R. Anderson. (T.P. 1393) Effects of Scrap in the Blast-furnace Burden. By C. L. T. Edwards. (T.P. 1270) Temperature Gradients through Composite Carbon Columns and their Application to Blastfurnace Linings. By F. J. Vosburgh and M. R. HatFIeld. (T.P. 1363) Correlations of Some Coke Properties with Blast-furnace Operation. By H. W. Johnson. (T.P. 1402) The Technical Cohesive Strength and Yield Strength of Metals. By D. J. McAdam, Jr. (T.P. 1414) Effects of Eight Complex Deoxidizers on Some 0.40 Per Cent Carbon Forging Steels. By George F. Comstock. (T.P. 1417) Significance of the Bessemer End Point. By H. T. Bowman. (T.P. 1428) Structural Diagrams of Nickel Irons and Steels. By J. T. EasE and N. B. Pilling. (T.P. 1432) Carbides in Low-chromium Steel. By Walter Crafts and C. M. OFFenhauer. (T.P. 1436) Hardenability Calculated from Chemical Composition. By M. A. Grossmann. (T.P. 1437) Recrystallization of Silicon Ferrite in Terms of Rate of Nucleation and Rate of Growth. By J. K. Stanley and R. F. Mehl. (T.P. 1438) The Solubility of Carbon as Graphite in Gamma Iron. By R. W. Gurry. (T.P. 1440) An Evaluation of the Factors Affecting Iron Oxide in the Open-hearth Bath. By J. E. Gould and H. J. Hand. (T.P. 1442) Precision in Creep Testing. By J. A. Fellows, Earnshaw Cook and Howard S. Avery. (T.P. 1443) Lattice Relationships in the Decomposition of Austenite to Pearlite, Bainite and Martensite. By G. V. Smith and R. F. Mehl. (T.P. 1459) Rate of Nucleation and Rate of Growth of Pearlite. By F. C. Hull, R. A. Colton and R. F. Mehl. (T.P. 1460) Weight Change as a Criterion of Extent of Decarburization or Carburization. By R. W. Gurry. (T.P. 1470) Observations in the Making and Use of Sulphite-treated Steels. By E. L, Ramsey and L. G. Graper. (T.P. 1476) Diffusion in Metal Accompanied by Phase Change. By L. S. Darken. (T.P. 1479) Engineering Properties of Heat-resistant Alloys. By Howard S. Avery, Earnshaw Cook and J. A. Fellows. (T.P. 1480) Distribution of Manganese and of Sulphur between Slag and Metal in the Open-hearth Furnace. By L. S. Darken and B. M. Larsen. (T.P. 1481)

Jan 1, 1942

Time as a Factor in the Making and Treating of Steel. By John Johnston. (Howe Lecture) (T.P. 1478) Influence of Chromium and Molybdenum on Structure, Hardness and Decarburization of 0.35 Per Cent Carbon Steel. By R. F. Miller and R. F. Campbell. (T.P. 1345) Mechanical Properties of Iron-manganese Alloys. By F, M. Walters, Jr., I. R. Kramer and B. M. Loring. (T.P. 1369) The Instability of Low-expansion Iron-nickel-cobalt Alloys. By I. R. Kramer and F. M. Walters, Jr. (T.P. 1370) The S-curve of a Chromium-nickel Steel. By B. M. Loring. (T.P. 1383) A Magnetic Determination of the A3 Transformation Point in Iron. By B. A. Rogers and K. 0. Stamm. (T.P. 1388) Rapid Tension Tests Using Two-load Method. By A. V. de Forest, C. W. MacGregor and A. R. Anderson. (T.P. 1393) Effects of Scrap in the Blast-furnace Burden. By C. L. T. Edwards. (T.P. 1270) Temperature Gradients through Composite Carbon Columns and their Application to Blastfurnace Linings. By F. J. Vosburgh and M. R. HatFIeld. (T.P. 1363) Correlations of Some Coke Properties with Blast-furnace Operation. By H. W. Johnson. (T.P. 1402) The Technical Cohesive Strength and Yield Strength of Metals. By D. J. McAdam, Jr. (T.P. 1414) Effects of Eight Complex Deoxidizers on Some 0.40 Per Cent Carbon Forging Steels. By George F. Comstock. (T.P. 1417) Significance of the Bessemer End Point. By H. T. Bowman. (T.P. 1428) Structural Diagrams of Nickel Irons and Steels. By J. T. EasE and N. B. Pilling. (T.P. 1432) Carbides in Low-chromium Steel. By Walter Crafts and C. M. OFFenhauer. (T.P. 1436) Hardenability Calculated from Chemical Composition. By M. A. Grossmann. (T.P. 1437) Recrystallization of Silicon Ferrite in Terms of Rate of Nucleation and Rate of Growth. By J. K. Stanley and R. F. Mehl. (T.P. 1438) The Solubility of Carbon as Graphite in Gamma Iron. By R. W. Gurry. (T.P. 1440) An Evaluation of the Factors Affecting Iron Oxide in the Open-hearth Bath. By J. E. Gould and H. J. Hand. (T.P. 1442) Precision in Creep Testing. By J. A. Fellows, Earnshaw Cook and Howard S. Avery. (T.P. 1443) Lattice Relationships in the Decomposition of Austenite to Pearlite, Bainite and Martensite. By G. V. Smith and R. F. Mehl. (T.P. 1459) Rate of Nucleation and Rate of Growth of Pearlite. By F. C. Hull, R. A. Colton and R. F. Mehl. (T.P. 1460) Weight Change as a Criterion of Extent of Decarburization or Carburization. By R. W. Gurry. (T.P. 1470) Observations in the Making and Use of Sulphite-treated Steels. By E. L, Ramsey and L. G. Graper. (T.P. 1476) Diffusion in Metal Accompanied by Phase Change. By L. S. Darken. (T.P. 1479) Engineering Properties of Heat-resistant Alloys. By Howard S. Avery, Earnshaw Cook and J. A. Fellows. (T.P. 1480) Distribution of Manganese and of Sulphur between Slag and Metal in the Open-hearth Furnace. By L. S. Darken and B. M. Larsen. (T.P. 1481)

Jan 1, 1942

By T. D. Jones

MUCH the same story can be told for the lead industry for the year 1945 as for the three previous years. In response to inquiries as to new developments, invariably the answer has been, "No new developments-our men either too busy with the man-power problem or trying to get production out." Time and efforts of industry have been concentrated for the most part on war or readjustment problems. Now that V-E and V-1 day have passed, the lead industry can justly be proud of its record in World War II. As in previous wars, lead played an important role and one of its most spectacular uses was in the production of the atomic bomb. We read that the part lead played was rather obscure, but as a protective agent, lead played a most significant role. "Since the materials in the Pile Plant are intensely radioactive, all storage and handling must be done behind thick concrete walls or lead shields. The material is never seen and all operations are auto matically controlled by a foolproof remote control system especially designed for this purpose." (Chews. & Met., Sept. 1945.) When our armies invaded the European theater of war and made a landing on Normandy beach, gasoline and oil for the motive power were furnished through miles of armored lead pipe. This amaz-

Jan 1, 1946

By Sheldon P. Wimpfen

EVERYWHERE in mining circles the talk is of this new development of hard faced or insert bits which hints of many changes to come in mining practice and rock drill equipment. In the past fifteen years new equipment has appeared in rapid succession which brought one change after another in rock breaking practice. Detachable bits were an innovation which met with wide success. Blasthole diamond drilling has proven itself. Only recently, fusion piercing was announced as a possible solution to the problem of breaking taconite ores. For several years this interest in new methods has been growing and various experimental usages of tungsten carbides in rotary type rock drilling bits have been partially successful. American experts in rock drilling have been concerned with the subject for ten years but actual commercial practice was begun by European manufacturers and mining companies. At this time nearly every manufacturer of rock drilling bits is working on some type of an insert bit. On the Rand, European manufacturers are testing out various types of insert bits. The problems relating to rock drilling in South Africa vary greatly from ours. The bulk of the drilling there is limited to the 31/2-ft holes that are drilled for breaking the gold bearing reef ore. Rock drilling in most mines is far more diversified. Both drifting and ore breaking call for holes varying in length from 4 ft up to as much as 50 ft and more.

Jan 1, 1947

By R. H. Richards, A. E. Woodward

In Rittinger's Aufbereitungskunde of 1867 occurs (p. 195) the following table, which shows the rate of falling in water of fragments of minerals, of irregular shapes and of five different specific gravities: Diameter of particles in millimeters. 10 8 6 4 3 2 1 .5 Sp. Or. Velocity in meters per second. Auriferous silver, 16..9 .8 .7 .57 .5 .4 .29 .20 Galena,. ..7.5 .62 .55 .48 .39 54 .28 .20 .14 Pyrites,. ..5.0 .49 .43 .38 .30 .26 .22 .15 .10 Quartz,. ..2.6 -30 .27 24 .19 .17 .14 .10 .07 Coal,. ..1.3 .13 .12 .10 .08 .07 .06 .04 .03 With the purpose of extending this valuable table, to cover a larger number of minerals and sizes of each mineral, and of making it more easy of application in deciding upon a sieve-scale for any group of minerals, we have prepared the curves of velocity of fall of bodies in water shown in Plates I., XI., 111. and IV., using Rittinger's formula V= 2.44d(8 —1) where V= velocity in millimeters per second. " D = diameter of particles in meters. " 8 = specific gravity of the mineral. These curves embrace a large number of specific gravities, and for each specific gravity the relation of the diameter of the mineral particle to the velocity of its fall in water is given for all diameters and velocities used in practice. The second diagram is an enlargement of the lower left-hand corner of the first, the third bears the same relation to the second, and in like manner the fourth to the third. Plate I, therefore, covers the work of the coarsest jigging 2 inches in diameter; and under

Jan 1, 1890

By H. A. Guess

AT the outset, said Mr. Guess, I may say that although I believe the present engineering courses in the various colleges and universities could be arranged to give the student within the same time limit a broader general education of un- doubted value, still I do not agree with the view held by many that engineers in comparison with those of other occupations-let us say doctors, lawyers, bankers, and so-called business men-seldom arrive at high executive positions. After all, we must remember that engineers are not very numerous as compared with the occupations just mentioned and therefore a lesser number reaching high executive positions stated numerically might be a larger number stated as a percentage. We all know there must be throughout the United States say three doctors to one engineer, but I don't think that even numerically there are as many doctors in high executive positions as engineers, and it is a fortunate thing for the country that doctors as a class are so busily engaged in alleviating sickness and suffering and in the advancement of medical science that they do not aim particularly for high executive positions.

Jan 1, 1926

THE Fall Regional Meeting of the Institute, which has now for some years been held in cooperation with the Western Division of the American Mining Congress, will be held this year at Joplin, Mo., in the heart of the great Tri-State district. This year the Tri-State Zinc and Lead Ore Producers Association is joining in the meeting. The Society of Economic Geologists will also take part though not offering any papers. The district in which the meeting is held includes adjacent parts of Missouri, Kansas and Oklahoma. Out in the heart of a fertile prairie farming country, it is one of the major mining districts of the world. It produces normally approximately one-third of the zinc ore mined in the United States which is equivalent to nearly one-half the zinc since the concentrate has always been notable for the height of its grade. Even in the depressed business year 1930, the American Bureau of Metal Statistics credits the district with 434,460 tons of concentrates equal to 217,230 tons of zinc out of 1,503,095 and 576,630 respectively for the country as a whole. This was equal to about one-seventh of the world's output of zinc, more than that of any foreign country. In addition about 75,000 to 100,000 tons of lead is annually furnished by the same mines. Elsewhere we present a general description of the district prepared for this meeting by J. C. Heilman, a Lehigh graduate, who has spent the past eleven years there and has had charge of explorations for many of the companies.

Jan 1, 1931

[Executive J. V. W. REYNDERS, Chairman WILLIAM H. BASSETT E. DEGOLYER I-I. C. BELLINGER RICHARD PETERS, JR. Finance GEORGE OTIS SMITH, Chairman H. A. GUESS F. JULIUS FOHS Admissions GEORGE D. BARRON, Chairman DAVID LEVINGER P. A. MOSMAN H. K. MASTERS J. A, SINGMASTER Alternates F. G. BREYER C. W. HAMILTON F. E. PIERCE]

Jan 1, 1928

By B. N. Das, P. A. Beck

THE o phases have a complex tetragonal structure with Lo/ao = 0.52 and 30 atoms per unit cell.1 A large number of such phases are now known to occur in various binary systems of the transition elements and they exhibit the following typical features: 2,3 The composition of binary o phases is variable, ranging from approximately A4B to ABI. With only a few exceptions, in the o phases the A-ele-ment comes from the V- or Cr- group of the periodic table, while the B-elements are from the Mn-, Fe-, Co-, or Ni- group. In the first long period the corresponding o phases of the V- and Cr-series have approximately the same compositions. However, as the B-element changes from Mn to Fe to Co to Ni, the mean composition shifts monotonously toward higher A-contents.2-4 For example, if the mean compositions of the various o phases with vanadium are compared with each other, the composition shift mentioned above becomes plainly visible: V 30Mn0 80 Vo.45Feo..,, Vo .,Coo. 45 and Vo.5Nio.3. Similiar composition shifts, although not the same composition values, were observed in u phases formed by second and by third long-period transition elements.3'4 This behavior, very characteristic of o phases, is in rather sharp contrast to the usually quite well-behaved stoichi-ometry of the Laves phases. In the latter, the AB2 stoichiometry predominates, with A the large atom and B the small atom.= The p phase occurs in the four binary systems of Mo or W with Fe or Co. On the basis of their crystal structure determination, Arnfelt and westgren6 ascribed to the p phase in the Co-W system the ideal composition W,Co7. Since all four binary pphases have nearly the same composition, it would seem quite plausible that some definite stoichiometry such as A6B7, might be characteristic of this phase, as AB2 is of the Laves phases. On the other hand, it has been noted,7 that the phases occur at average electron concentrations near to those at which the various cr phases are found. Also, it has been pointed out by Shoemaker and associates8 that structurally the a phases and the p phases are somewhat related to each other; both of these structures may be described in terms of suitable stackings of quasi-hexagonal layers'of atoms. By studying a suitably chosen ter- nary phase diagram, one might expect to be able to find out which one of the two conditions, the analogy with the o phase or the constant ratio between the number of large atoms and the number of small atoms in effect governs the behavior of the p phase. Several isothermal sections of ternary systems containing o phases have been investigated. In all cases where two binary o phases occur, these were found to be connected b a more or less straight ternary o phase field.7' '10 Such elongated o phase fields were also found in ternary systems in which only one of the limiting binaries is known to contain o phase. In this manner a latent o forming tendency could be detected and the virtual composition of a "binary o phase", which does not actually occur as such was approximately determined by extrapolation. The behavior of the phases, including their composition shift, is analogous to that of the classical electron compounds, as described by Hume-Rothery.11 In order to decide whether the p phase is essentially a "size compound" like the Laves phases, where a fixed stoichiometric ratio is quite generally maintained between the "large atoms" and the "small atoms", or whether the p phase is typically an "electron compound" in the same sense as ois, it was decided to investigate an isothermal section of the Mo-Mn-Co system. The Mo-Co system12 and the Mo-Mn system13 each are known to have a binary o phase. It could be therefore expected that a ternary o phase field will connect these two binary cr-phase fields. The p phase is known to occur in the Mo-Co system. If the p phase should turn out to form an elongated phase field extending deep into the ternary system, the following considerations mighto apply. The atomic radius of manganese (1.314for C.N.12) is between the va,lues for Mo (1.40Afor C.N.12) and for Co (1.26Afor C.N.12). If it is assumed that p is a "size compound", and that Mn is substituting for the smaller Co atoms in the p-structure in the ternary system, the y-phase field might be expected to extend parallel to the Mn-Co binary line. If Mn is substituting for the large Mo atoms in the p-structure, the p-phase field may be expected to extend parallel to the Mn-Mo binary line. On the other hand, if the p-phase turns out to be an "electron compound" like o, the ternary p-phase field should extend parallel to the ternary o -phase field connecting (Mo,Mn)owith (Mo, Co) a

Jan 1, 1961

By R. M. Goldhoff, J. W. Spretnak, R. Speiser

IT has been observed by Grange and Garvey' that the homogenization of boron-treated steels could lead to complete elimination of the hardenability effect caused by boron. The experimental conditions leading to this conclusion involved the heating of steel specimens with and without boron at 2350°F for 24 hr. To prevent oxidation and decarburization, the specimens were encapsulated under vacuum in silica tubes. This observation of permanent deterioration of boron effect was noted in both a 0.63 pct plain carbon steel and a 0.25 pct C low alloy steel, both of which had been treated with ferroboron and homogenized at 2350°F for 24 hr. In another series of boron-treated steels which had been homogenized for shorter times, the effect was to reduce, but not completely eliminate, the boron effect. Under these circumstances, it was presumed that longer heating times would cause permanent deterioration of the boron effect in this series of steels also. Since the characteristic grain boundary constituent could not be formed in any of these steels after homogenization, it was concluded that possibly boron was being converted into an ineffective form through chemical combination resulting from prolonged heating at high temperatures. Assuming the validity of this observation, a series of experiments to establish the relationship between temperature of homogenization and kinetics of deterioration was contemplated. Initially an attempt was made to reproduce the results just described. For this purpose commercial lots of AISI 8640 and AISI 86B40 steels were used. The analyses of these steels appear in Table I. Hardenability evaluation was on the basis of the hardness of normalized sections. Grange and Garvey' pointed out that these steels are air hardening to some extent and such a technique can be used. For these tests the specimens were held for 20 min in a salt bath at 1600°F and then cooled in still air. Several evacuated silica capsules containing pairs of the test steels were made up and heated for 24 hr at 2350°F. A number of failures occurred among these capsules, but evaluation of the specimens successfully treated indicated a complete deterioration of the boron effect. However, examination of the surface of the treated specimens showed that some reaction, probably with the silica tube, had taken place, since none of the specimens was bright. One further test was made at 2350°F for 12 hr, using a pair of specimens wrapped in tantalum foil prior to encapsulation. These specimens appeared bright after treatment, and their hardenability evaluation showed that no deterioration had taken place. Since these steels are extremely sensitive to de-boronization at high temperatures and particularly at long times of holding, the experimental observations raised some doubt as to the real occurrence of the permanent deterioration effect. To resolve this question an experiment was undertaken in which the high temperature portion of the treatment was completed in vacuum. For this purpose a molybdenum wound resistance furnace capable of maintaining good vacuum was used. All the pertinent accessories to this furnace were machined from molybdenum stock in order to withstand the high temperature involved in the experiment. With this equipment a temperature of 2400 °F was obtained and held under a pressure of 5x10-" mm Hg for 24 hr. A specimen of each of the two test steels was suspended in the furnace and both were heated simultaneously. Temperature was measured with a standardized Pt—Pt-13 pct Rh thermocouple, whose millivoltage at 2400°F was extrapolated from the standardization equation, good up to 2200°F. The complete evaluation of these specimens is shown in Table 11. The hardness values attained by each steel after normalizing, both before and after the prolonged high temperature treatment, remain the same. A microscopic study of the decomposition products present in the microstructures of specimens at various points in the heat treatment correlated with the hardness values observed. It seems that no permanent loss of boron hardenability effect occurs, at least in these Grainal-treated steels, when deboronization is circumvented. Acknowledgments This work was conducted under the sponsorship of the Aeronautical Research Laboratory, Wright Air Development Center, under Contract No. AF 18(600)-94, and their support and permission to publish is gratefully acknowledged. A note of thanks is also extended to the Republic Steel Corp. for supplying the materials used in the work. References ' R. A. Grange and T. M. Garvey: Factors Affecting the Harden-ability of Boron Treated Steels. Tro.ns. ASM, 1946, vol. 37, p. 136.

Jan 1, 1957

Aamot, Olav Crone, (M'29) Chem. Engr., Elektro¬kcmisk, Raadhusgt. 32, Oslo. Norway. . Aase. Glenn D., (J'40) Jr. Met., American Smelt. & Refin. Co., Selby, Calif. Abadie, Henry G., (J'43) Petr. Engrg., Avenal, Calif. Abadilla, Quirico A., (M'38) Min. Engr., Dir., Bureau of Mines, Manila, P. I. Abbott, Agatin Townsend, (J'40) Jr. Engr., Phelps Dodge Corp., Morenci Branch. Morenci. Ariz. Abbott, Clarence E., (M'04) Civ. Engr. V.P., Tennessee Coal Iron & R.R. Co., 1542. Brown Mars Bldg. Birmingham. Ala. Abel, Raymond L.. (M'23) Chem. Engr., Com¬manding Officer, Pittsburgh Chem. Warfare urement Dist., American Bank Bldg.. Pittsburgh. Pa. Abel, Walter D., (M'32) Min. Engr., Supvr. Engr.. R.F.C., Los Angeles, Calif. Abele, Louis T., (M'31) 423 3rd Ave., Decatur. Ga. Abell, Leo M.: (M'31) Mill Supt. & Met.. Em¬ peror Gold Min. Co., Ltd., Vatukoula. Fiji Islands. Abernathy, G. E., (M'38) Geol., Kansas State Geol. Survey, Pittsburg, Fan. Abernathy, Jack H., (M'40) Cons. Petr. Engr., First National Bldg.. Oklahoma City, Okla.

Jan 1, 1943