Search Documents

By J. L. Walter

Tungsten ingots with and without small amounts of aluminum, silicon, and potassium were prepared by conventional powder-metallurgy techniques and hot-rolled to 0.001-in.-thick sheet. The ingots were rolled three different ways: I) initially cross-rolled, then straight-rolled; 2) straight-rolled, and 3) straig-ht-rolled, then cross-rolled. Total reductions were 99.8 pct. Samples of the sheet were annealed, in vacuo, at temperatures from 1200" to 2200°C. Substructures and textures were determined by transmission electron microscopy and X-ray diffraction. The doping agents were found to form particles of mullite (Al,Si,O,,) which, on rolling., appear to form strings of particles aligned parallel to the rolling direction. These strings of purticles are associated with an increase in the recrystal-lizution temperature from 1400°C for undoped sheet ThE addition of small amounts of aluminum, silicon, and potassium to tungsten has a profound effect on the grain structure of drawn and recrystallized wire.'" The grains generally do not occupy the entire cross section of the wire and have lengths many times the wire diameter. The grain boundaries are, in general, nearly parallel to the wire axis and have long ''fingers" projecting one into the other as may be seen in Fig. 1, a longitudinal section of recrystallized doped wire. When unsuitable additions or no additions are made or the wire is not sufficiently reduced during draw- to 2000°C for doped sheet. The particles also limit lateral grain growth while allowing growth parallel to the rolling direction. This results in the formation by primary re crystallization of large highly elongated grains of specific preferred orientation. The undoped sheet recrystallized to small equiaxed gains. The preferred orientations of the large grains were determined from axis density plots to be (113) (691). (0i3) (362), (116) (304) types for the initially cross-rolled then straight rolled material. These orientations are similar to the orientations of the large elongated grains in doped and heavily drawn tungsten wire. The nucleation of the large grains appears to occur by recovery of certain of the polygonized regions of specific orientation, followed by strain-induced boundary migration.

Jan 1, 1968

By C. E. Brown, D. C. Helms, O. W. Shimer

The early history and progress of anthracite stripping, from the first known operation at Summit Hill in 1821 through 1917, was covered in 1917 in a paper by J. B. Warriner,1 then chief engineer, now president of the Lehigh Navigation Coal Co., and stripping methods between 1917 and 1931 were the subject of a paper in 1931 by H. H. Otto,2 of the Hudson Coal Company. . The present paper is confined to methods used today on pitching beds in the western middle and southern anthracite fields. The anthracite industry, not unlike other large industries, had been affected for more than a decade by the adverse economic conditions of the country. High development and operating costs and the competition of other fuels caused some collieries to be closed temporarily, while others were permanently abandoned. In order to obtain a larger tonnage at a lower development cost, a larger stripping program was put into effect by many companies. In 1932, stripping operations accounted for 3½ million tons, or 7 per cent of the total anthracite production of the year, and in the next 10 years this increased until more than double that amount, or over 14 per cent of the total production, was from stripping operations. These figures represent the total production of the entire anthracite region; unfortunately, the figures have not been separated from the different fields. There are some operations in the southern and middle western fields where the tonnage obtained from stripping amounts to more than 30 per cent of the total colliery production. Stripping operations on pitching beds present difficult problems. Owing to the various geological formations, a different situation is encountered in nearly every stripping pit; and because of the proximity of an overlying bed, it is very often necessary to load the entire overburden into trucks and haul it out of the pit to the dump area, although back filling and casting is done whenever possible. Beds in the areas described in this paper pitch from 20" to 90 and some are on the invert in many sharp folds and faults. Planning The more successful strippings have had adequate engineering analysis. Some work is being done without much preliminary planning, but many strippings would have failed completely if close supervision by the engineering department had not been . maintained. Locations of stripping areas are determined as follows: I. By constructing cross sections over the areas and drilling sufficient diamond-drill or well drill holes to study the strata and to determine the location, thickness

Jan 1, 1944

By Paul F. Kerr

Uranium mineralization occurs in the footwall of the Sunshine vein from the 2900 to the 3700 level. Veinlets of uraninite associated with pyrite and jasper have been so extensively divided and recemented that units more than a few feet in length are seldom observed. The wall rock is St. Regis quartzite of the Belt series. The age of the uraninite, on the basis of isotopic analyses, is 750 t- 50, which agrees with geological data suggesting that phases of the Sunshine mineralization are pre-Cambrian.

Jan 5, 1953

By Milton H. Fies

EARLY in 1945 the laboratories of the Southern Research Institute will begin active research investigations on behalf of industrial clients. This achievement has come after four years of planning by a group of Alabama businessmen, and is in partialanswer to an urgent need in the South. Those who conceived the Institute have long realized that a marked relationship exists between scientific research and the economic well-being of the several regions of the country. Clearly, technological research, generally absent in the South, is the medium through which are created new finished goods industries, and the increase of technological research is perhaps the most important long-range project in the South.

Jan 1, 1945

By Warren Howes, C. O. Anderson, Robert E. Illidge, M. D. Harbaugh, S. J. Burris

The Tri-State zinc-lead mining district embraces an extensive area, including the northeastern part of Ottawa County, Oklahoma, the southeastern part of Cherokee County, Kansas, and adjacent portions of Missouri, mainly in Jasper County. The Oklahoma-Kansas portion of the district, in the vicinity of Picher, Okla., has been the principal producing area since 1917, and the present milling practice in that section is the subject of this paper. This district is the largest zinc-producing field in the United States. In 1926 it produced 55 per cent of the nation's zinc and 15 per cent of its lead, and in 1933 it produced 35 per cent of the zinc and 10 per cent of the lead. From 1842 to 1933, inclusive, the total output of the district was 18 1/2 million tons of zinc and lead concentrates valued at 818 million dollars. Of this production, the Oklahoma-Kansas, or Picher, field yielded over 9 million tons valued at over 400 million dollars. Mining operations in the Oklahoma-Kansas field near Picher and Baxter Springs began in 1915. The mills built it that time consisted merely of gravity concentration plants employing jigs and tables and the same flow sheets as had proved satisfactory with the free-milling ores such as were mined in the Joplin-Webb City fields in Missouri. The Kansas-Oklahoma ores proved to be much richer but also more refractory to treatment than those in the Joplin area, and contained a considerable percentage of zinc mineral not freed by the amount of crushing usually practiced in preparing the ores for jigging. Thus the old Joplin type of mill, with its usual two or four jigs and a few tables, proved inadequate and resulted in excessive tailings losses sometimes as high as 50 per cent

Jan 1, 1935

By C. D. Wiseman

THE concept of alloying to increase the strength of metals originated during the bronze age. However, at the present time there is no single theory capable of explaining all of the observed strengthening effects of alloying elements on the mechanical properties. In general, it may be said that solid solutions are stronger than the pure metal and that the strengthening effect increases with increasing alloy content. Various theories for solution hardening have been proposed, the first of which was presented by Rosenhain who suggested that the alloying elements roughened the slip planes, thereby requiring a higher stress to initiate slip. Recent work by French and Hibbard2 confirmed Norbury's3 conclusion that those alloying elements which cause a greater change in lattice parameter have larger effects on hardness. However, a given change in lattice parameter produced by different alloying elements does not cause the same change in hardness. A further refinement was suggested by Dorn, Pietrokowski, and Tietz4 who considered differences in valence between the solute and solvent with the change in lattice parameter to explain the plastic properties of aluminum alloys. Allen, Schofield, and Tate5 further investigated the valency contribution to solution strengthening by testing some copper-base solid-solution alloys having constant electron densities. Tensile tests performed on these alloys gave identical stress-strain curves even though the atomic size effect, which varied by a factor of two, was neglected. The advent of dislocation theory6-8 provided a new and powerful tool capable of explaining many phenomena of plastic deformation and indicated new approaches to solution hardening. The basic con- cept of recent theories is that solution hardening is not due to stresses associated with randomly dispersed solute atoms, but rather to a nonuniform distribution of the solute. This conclusion was reached by consideration of the effective tension present on each dislocation line and the ability of a dislocation to pass an obstacle. cottrell suggested the possibility that the internal stresses due to randomly distributed solute atoms would offer essentially no resistance to the passage of dislocations. He reasoned that an edge dislocation may be considered as a rigid line discontinuity. As the dislocation moved through a crystal, the random stress fields would be equally distributed along its length. Since half of the stress fields would be acting to move the dislocation forward and the other half trying to move it back, the net effect on the dislocation would be zero. Thus the randomly distributed solute atoms would not contribute appreciably to solution strengthening. Mott and Nabarro10 considered the dislocation as a flexible, rather than a rigid, discontinuity. They obtained a simple model for a dislocation moving in a lattice having precipated particles, where the dislocation would actually bend around the obstacle until it would loop back onto itself to rejoin and then continue onward. Their work indicated that the minimum radius of curvature of the dislocation line, under the action of an external stress and in the region of an internal stress, would be such that the dislocation would be unable to pass through a matrix containing small closely spaced precipates by the looping process. The dislocations would tend to remain rather straight, approaching the condition of Cottrell's rigid dislocation. Hence, the strengthening must not be due to random solute atoms; however, it might be due to the concentration of atoms, either as clusters of like atoms or as short-range ordered regions, or to the concentration of solute atoms around dislocations. To date, four mechanisms of solution strength-

Jan 1, 1959

By Robert A. Cook

In the increasing struggle to cheapen the cost of our iron and steel products a great deal of attention lias been given to economies in the manufacture of coke; and while but little lias been accomplished in this direction in the United States, the narrow margin between cost and market-price, which has obtained here for the past few years of continuing manufactur ing depression, has brought the coke-maker face to face with the problem, how to save, and benefit by it, the hitherto waste products of distillation. I These may be summed up under three heads, generally rank ing, in value, in the following order: 1. Ammonia salts.. 2. Oil- or tar-products. 3. Gas. There are cases in which the last may assume the position of greatest importance. The greatest obstacle encountered by the American coke maker, on investigating the subject, has been the apparent necessity of discarding his existing plant of bee-hive ovens, and erecting an entirely new and very expensive system of retort ovens, against the product of which Be has probably been prejudiced from his earliest knowledge of the subject. The object of this paper is to bring prominently before our coke-experts a brief history of the development at Sheffield, England, of a most successful system of the utilization of by products in connection with all already existing plant of bee hive ovens. This system has now been in satisfactory operation for about five years, and is applied to a series of blocks of ovens, comprising-about 140- in all At this plant, belonging to the well-known firm of Newton,

Jan 1, 1897

By R. D. Pehlke, P. D. Goodell, R. W. Dunlap

The rate of dissolution of steel bars in molten pig iron has been measured experimentally in the temperature range 2300° to 2650° F. The rate of solution is shown to be a .function of bath composition, temperature, and stirring. A kinetic model based on carbon diffusion in the liquid phase has been derived to fit the experimental results. THE rate of scrap melting has long been an important variable in steelmaking operations. With the advent of the oxygen steelmaking process and the accompanying shorter heat times, the rate of scrap melting has now become one of the rate-limiting factors in steel production. As observed in commercial practice, the solution rate is influenced by the compositions of liquid and solid, the temperature, agitation, and time. However, no definitive work has been done on the Fe-C system, and there is very little information in the literature regarding the relative effects of these variables in steelmaking systems. A number of questions have been raised in regard to scrap utilization in basic oxygen steelmaking operations. Consideration has been given to the optimum size and shape of scrap, and to the use of preheated scrap as a means for decreasing the pig-iron requirement in oxygen blowing. The determination of an optimum scrap practice for a specific installation depends to a large extent upon the economics of the scrap market and also upon the behavior of scrap in the vessel. The present research was undertaken as a preliminary study in evaluating the behavior of steel in a pig-iron bath under various conditions of temperature, composition, and agitation, as might be encountered in oxygen converter operations or in any steelmaking operation where scrap behavior is an important process variable. Related studies have been carried out on non-ferrous systems. The solution rate of solid aluminum in a molten A1-Si alloy has been studied.' Furthermore, the increasing use of liquid metals has created considerable interest in studies related to dissolution of a solid in a liquid, or mass transfer taking place between a solid interface and a liquid metallic phase.2-10 In an effort to clarify the relative importance of factors influencing the dissolution of scrap in Fe-C alloys, this paper presents the results of a study of the rate of dissolution of a low-carbon steel cylinder in a molten Fe-C bath at various bath compositions, temperatures, and conditions of agitation. An attempt has been made to determine the mechanism of solution, and a model has been derived to fit the experimental results. The rate of heat transfer between the molten pig-iron bath and the solid-steel cylinder has also been studied. EXPERIMENTAL PROCEDURE A molten bath of pig iron (nominal composition 4.2 pct C, 0.5 pct Mn, 0.8 pct Si)* was held in a 200- *In view of the fact that the composition of the pig-iron bath was slowly changing with time because of steel dissolution and reaction with the surrounding atmosphere, intermittent samples of the liquid bath were taken throughout each experiment, Table 1. lb induction melting unit. The internal diameter of the furnace was 8-1/2 in. and the bath depth approximately 14 in. Cold-finished 1020 steel cylinders of 1/2-, 3/4-, 1-, 1-1/2-, and 2-in. diameters were cut into 1 -ft lengths for use as test specimens. One end of each bar was machined to fit a hand-driven, mechanical stirring device which rested on top of the furnace. This fixture permitted 7 to 8 in. of the bar to be immersed in the melt. The steel cylinders were cleaned to free the surface of grease and oxide. The rods, at ambient temperature, were immersed into the molten pig-iron bath. The melt temperatures studied in this investigation were 2300°, 2500°, and 2650°F. Different agitation conditions were achieved by operating with a) the power to the furnace, giving induction stirring; b) induction stirring plus mechanical stirring, using hand rotation with a chain and sprocket assembly at approximately 200 rpm; c) mechanical stirring alone with the power off; and d) the power off and no mechanical stirring resulting in minimum agitation, i.e., only that caused by natural convection currents in the bath. The samples were immersed in the melt for prescribed times ranging from 30 sec up to 6 min. Immersion times were measured with a stopwatch and temperature control of the melt was achieved by power adjustment following temperature measurement with an optical pyrometer. The measurements with the calibrated pyrometer were checked out to within less than 10°F with simultaneous thermocouple measurements. Following immersion, the bars were water-quenched and the diameters were measured with a micrometer at several positions on the reduced area, and by volumetric displacement. The dissolution rates calculated from the

Jan 1, 1965

By D. S. Choi, R. Stefanko

There are a number of complex factors that influence the effectiveness of anchorage to maintain tension in rock bolts. However, a plastic analysis of the anchorage site employing certain simplifying assumptions with application of the Mohr-Coulomb criterion appears to explain the observed phenomena. Such an analysis has been made and a correlation sought with field and laboratory tests. Field tests were made in an anthracite mine in eastern Pennsylvania and included pull tests and long-term tests of a variety of anchorage devices in two basic lengths, 30 and 42 in. in two widely differing seams. Performance is reviewed for wedge, expansion shell, and resin anchorage. Laboratory tests duplicated many of the field conditions but in addition compared the performance of shells with normal and reversed serrations. This performance was compared with the predicted results from the plastic analysis. One of the major problems in conducting long-term underground tests is the selection of suitable instrumentation. All installed bolts were fitted with spherical and hardened washers to insure the best possible torque wrench readings. In addition, commercially available load cells were used. Finally, the performance of a specially developed strain-gage-equipped ring cell is viewed. Rock bolting as a method of support continues to increase with applications in many other industries in addition to mining. Nevertheless, with nearly 55,000,000 roof bolts installed in coal mines alone last year, this remains as the single greatest use. While bolts have frequently supported ground where conventional timbering could not, there are relatively few design criteria; and trial-and-error procedures prevail. Furthermore, there has been a lag in development of suitable instrumentation that is simple to install and read out, sensitive, durable, reliable, safe, and economical in evaluating the effectiveness of a bolt over long periods of time. Therefore, the pull test continues to be the most popular method of evaluating the applicability of a certain type of roof bolt under specific installation conditions. At The Pennsylvania State University in the Dept. of Mining, research has been conducted for a number of years to measure bleed off in carefully controlled laboratory experiments as well as in underground investigations."-' Unfortunately, most of the instrumentation developed has been primarily suitable only for research purposes, not possessing all of the aforementioned characteristics desirable for routine underground use. Other groups also have met with restricted success. Therefore, while relatively crude, the torque wrench continues to remain as the most widely used load measuring device. While both field and laboratory tests continue to be con- ducted, analytical analyses are attempted to discover the more important design parameters in order that more efficient anchorage might be devised. Bolts are being used for a greater variety of purposes in mining. Suspending wire sideframe belt conveyors from roof bolts is a common application. The suspension of a monorail transportation system presents yet another. One such system has just been installed in a recently reopened anthracite mine and is presently being evaluated under production conditions. Preliminary studies revealed that a considerable cost reduction was possible by suspending the monorail on bolts anchored in the top. The monorail was to be installed under two widely differing conditions—a competent sandstone above the Buck Mountain seam and a softer shale top above the Skidmore. The type of anchorage device, length of bolt, and long-term performance, consistent with economy and safety, had to be established for the installation once the decision was made to suspend the system on rock bolts. This paper describes some of the testing procedures leading to a final selection. Theoretical Analysis of Expansion Shell Anchorage A detailed look at an expansion shell assembly might shed some light on the factors involved in the design of a suitable shell, Fig. 1. When a bolt is rotated, the tapered plug is forced downward, expanding the leaves laterally to grip the sides of the hole. Two friction surfaces are present: (1) the interface of the plug and leaf and (2) the interface between leaf and rock. The relationships of these friction planes, geometry of expansion shell, and properties of the rock are important in the design of an expansion shell. Therefore, an analysis assuming the rock to behave as a rigid plastic material with its yield governed by the Mohr-Coulomb criterion was made." Furthermore, the effect of friction between the leaf and rock produced by serrations was analyzed.

Jan 1, 1971

By C. S. Barrett

THE crystal imperfections known as faults in stacking (stacking disorder) are of importance to both fundamental and applied science and are receiving increasing attention. On the theoretical side there have been recent advances in the analysis of diffraction patterns in terms of stacking faults, and on the experimental side it has been found that certain metals develop a faulted structure on cooling through a phase transformation. Beyond this, little is known of what may be called the physical and mechanical metallurgy of faulting, although there has been no lack of discussion and conjecture as to the presence of faults in metals and the effect of faults on mechanical properties and microstructures. In the close-packed metals the nature of faults can be described very simply. Face-centered cubic (FCC) crystals consist of close-packed layers of atoms, (111) planes, stacked above each other in a definite manner. If one layer is designated as the A layer, the next must be a B or a C layer; that is, every atom of the second layer lies not above the atoms of the A layer, but nestles in the hollows between these, using the hollows designated as the B positions, or the equivalent hollows designated as C. If the sequence of layers is ABCABC...., so that layers three spacings apart are directly over each other, the crystal is FCC; if CBACBA ... it is an FCC crystal that is a twin of the former; if ABAB........or BCBC..it is hexagonal close-packed (HCP). A fault is a break in the sequence, such as ABCABABC .. . which has the effect of inserting an HCP lamella into an FCC crystal. Regularly spaced faults spaced two layers apart would convert an FCC crystal entirely to HCP, or an HCP to FCC. A fault in an FCC crystal is also equivalent to creating an FCC twin of minimum thickness; in fact, the entire crystal would be converted to its twin if faults were introduced regularly. (In HCP crystals, however, twinning does not occur on the basal plane and a fault on this plane is not identical with a thin twin). Faults are one of the possible causes for annealing twins,' for the strain markings that are brought out by etching deformed metal,'," for the altered X ray reflecting power of metal at slip bands that is revealed in X ray reflection micrographs,' for the extinction of Kikuchi lines in electron diffraction patterns, and for the hardening of latent slip planes.' Since other explanations of these effects are also available," there has been no direct proof of faults from deformation; yet it has appeared likely that they would occur. Faults resulting from phase transformations in metals, however, have been clearly revealed by diffraction in cobalt" and lithium. It is to be expected that the faulting tendency is greatest

Jan 1, 1951

By W. B. Heroy

ONLY through the mineral fuels can large amounts of energy be transported to great dlstances and stored for long periods for future use. Coal has the advantages over oil of greater safety of handling and smaller losses in storage. But oil is, in the present stage of technical advancement, the more economical source of liquid fuel for internal-combustion motors. No method for direct use of coal in such motors has been developed that can compete with petroleum products. The automoblle engine and the airplane motor are designed to make the most effective use of gasoline.

Jan 1, 1944

By ROBERT B. COONS

SELECTIVE SERVICE must meet three important demands for man power: (1) Activities concerned with production of war goods. (2) The armed forces. (3) Civilian activities and institutions the continuance of which are essential to maintaining the structure of our American democracy. In the above enumeration of demands I have placed everything, including most of our most prized possessions and activities, after the demand for men for war production and the armed forces. To establish an order between the latter two is difficult. For the time being, at least, the Selective Service policy is to make sure that we avoid the risk of "too little and too late." No soldier, sailor, or marine should be sent from these shores to risk his life without the assurance of having a gun, clothes, food, and medical supplies. Therefore, the premium is now being placed on man power for war production and in our process of selection no stone is left unturned to see that our agencies are fully informed of the needs of war production. Our procedures set up recourses for employers of war-production man power so that their activities need not be disrupted, at least not until they have had time to train replacements.

Jan 1, 1942

By Robert Anderson

ROUGHLY, a crack in a casting may be considered, for the moment, to be due to fracture of the alloy resulting from the stress set up by the contraction in volume on passing from the liquid to the solid state. Cracks may be external or surface, internal or deep-seated, or incipient or so-called strain cracks. Draws may appear as depressions, unevenness, and "pinching in" of the surface of a casting. Roughly, draws are due to contraction in volume and are governed largely by the same factors as cracks. A casting may be cracked, however, without being drawn. Shrinkage is a foundry term; it connotes the contraction in volume of a metal or alloy on passing from the liquid to the solid state. Pattern-makers' shrinkage is the total contraction in volume (including liquid, solidification, and solid shrinkage) that occurs when an alloy is poured into a mold. The contraction in volume of aluminum is one of the principal factors affecting the occurrence of cracks, as will be shown later, and the question of shrinkage and its control requires careful study in any treatment of cracking in castings. In the case of, sand and die castings, cracks have been attributed to a number of causes, but in the case of most light aluminum alloys, they are due to the large contraction in volume on freezing and the lack of its regulation or control. The most important factors are: (1) Contraction in volume; (2) composition of alloy; (3) quality of melting charge; (4) design of casting; (5) method of molding; (6) hardness of ramming; (7) method of gating; (8) hardness and characteristics of cores; (9) chills; (10) risers; (11) melting temperatures; (12) furnace used for melting; (13) pouring tempera-tures; (14) inclusions in alloys; (15) hot shortness of alloys; and (16) physical properties of alloys at high temperatures. Of these, the first, second, third, and eleventh to sixteenth involve ascertainable metallurgical facts; the remainder are largely matters of opinion, judgment and technical knowledge of men experienced in the production of castings.

Jan 10, 1921

By K. Mukai, M. Ishihara

This report is a brief discussion of the impurity levels both in primary aluminum and super-purily alnminim in connection with raw materials and proc-essing methods. Particularly, truce amounls of im-purities were analyzed by introducing nittss-speclro-gruphy and nenlron-aclivalian analysis techniques. Vanadium and gallium content in primary aluminum metal corresponded to theor amounls in anode coke. but the nickel content in primary aluminum was hide-pendent oj its amount in the anode cake. Sulfur in the anode colic might result in an increase of the iron content in the molten metal in the reduction cell. The content of sodium and calcium increased with increasing bath ratio. In the holding furnacc sodium content decreased rapidly, and nonmetallic inclusions merit separated front the mollen metal. Three-layer elctrolysis was effectire in eliminating many impuri-ties with the exception of copper, aluminum oxide. aluminum nitride, and some rare-earth elements. THE amount of impurities and nonmetallic inclusions in aluminum metal depends on impurities in the raw materials and various production processes. This paper presents an investigation of the behavior of impurities and nonmetallic inclusions in aluminum during the electrolysis process, the period in the holding furnace, and the process of three-layer electrolysis. Chemical analysis and emission spectrometric analysis have generally been used as methods to determine small amounts of impurities in both primary aluminum and super-purity aluminum; however. mass spectrography and neutron-activation analysis have been recently introduced into this field, and trace amounts of impurities can accurately be determined by these latter methods. EXPERIMENTAL WORK Common impurities were determined by means of absorptiometric. polarographic, flame-photometric. and emission-spectrometric methods. However, in the determination of trace amounts of impurities and non-metallic inclusions, the following methods were applied. In the analyses of trace impurities by mass-spec- trographic analysis, samples were exposed in the vacuum spark of double-focus ing Mattauch-Herzog type mass spectrograph (Japan Electron Optics Laboratory, Ltd.). Ilford Q2 photographic plates were used as ion detectors. Fe was used as the internal standard, and the atomic concentration of each element was calculated by the following expression and converted into the weight concentration: where E, and Ei are the exposures (coulomb) when isotopes of the internal standard and impurity elements (on which the estimate is based) show the same density, X is the percent (atomic) concentration of the standard, IF and Ii are the percent abundances of the isotopes of the standard the impurity elements (on which the estimate is based), and Ms and hfi are the mass of the isotopes of the standard and impurity elements (on which the estimate is based). The coefficient of variation in this method is about 40 pct in the range of 0.1 to 1 ppm. In neutron-activation analysis, irradiations were done in the nuclear reactors TRIGA-I1 (neutron flux: 4.7 x 10 11 n per sq cm per sec; Rikkyo University) or JRR-2 (neutron flux: 2 x 1013 n per sq cm per sec: Japan Atomic Energy Research Institute). After the chemical separation, a NaI (3 by 3 in.) scintillator connected to a 256-channel y-ray spectrometer (R.C.L.) was used for counting and recording various activated impurities. The coefficient of variation in this method is about 20 pct. In the analyses of nonmetallic inclusions, aluminum-oxide determination was carried out according to Fischer's method, 3 as follows. A slice of sample was cut off and the surface was cleaned. It was dissolved in bromine-methanol. The solution was filtered and the residue was washed. The residue was fused with potassium bisulfate flux. Then it was dissolved in weak acid, and oxine solution was added. The aluminum oxinate was extracted with benzene. Finally, aluminum was determined absorptio-metrically. Aluminum nitride determination was carried out as follows. A slice of sample was cut off and the surface was cleaned. It was put in the distillation apparatus and decomposed with sodium hydroxide solution. The solution was distilled. Then ammonia was absorbed and

Jan 1, 1967

By Charles Malcolmson

IN the United States, improvements in methods of combustion have made possible the use of the smaller sizes of anthracite. This coal is now being reclaimed from the culm banks accumulated by the miners in the more prodigal years. To-day the freshly mined "slush" is segre¬gated and stored against the time when, through briquetting or some other means, it may be utilized as a commercial fuel. For many years Europe has achieved enviable results in the conservation of her small coal by briquetting. This profitable industry, first placed on a commercial basis in France in 1842, has grown to such magnitude that the "'production during 1913 exceeded 36,000,000 short tons. Briquets produced in Great Britain are used principally for steam purposes and the greater part of the output is either exported or taken by the Admiralty. On the Continent the briquets are sold in all branches of the coal trade. The French railways consume from 16 to 40 per cent. of their fuel in briquet form, and in Germany the lignite briquets, (of which 20,000,000 tons were produced in 1913) are as familiar and interesting to the American traveler as the huge porcelain stoves in which they are burned. It is not strange, therefore, that aggressive and far-sighted promotors heralded this means of converting our ubiquitous coal waste into revenue. To the superficial student the briquetting process seemed so simple as to make success easy. It is for this reason principally that the path of the industry in America has been strewn with failures. The rash enthusiast had either not worked out the mechanical problems involved or had failed to grasp the local conditions under which the briquets must be made and sold. It may be confidently stated, however, that in spite of the many vicissitudes through which it has passed, coal briquetting is now an accomplished economic success in this country, and as a profitable adjunct to the coal industry it has come to stay.

Jan 2, 1915

By R. W. Waterfill

MANY existing ore deposits of valuable metals have been worked out in their upper surface levels and the continued productivity of these mines is dependent on their extension to greater depths in the earth. The maximum depths at present reached are about 6000 to 8000 ft. below the surface, with no evidence of an impoverished ore vein. These mines are widely distributed; some of the best known are in South Africa, Brazil, India and in the western sections of the United States. Among the factors which increase the difficulty of working these mines at increasing depths are hoisting, rock pressure and temperature. The manner and effectiveness with which these problems are met will, no doubt, determine in a large measure the ultimate depths to which any mine can be profitably worked. The most critical of these three factors at present is the increase in temperature with depth. The high temperature and humidity in many of these mines at present is severely detrimental to the health of the workers and greatly hampers their efficiency. Some have almost reached a condition in which the human system cannot survive. The problems involved in the cooling and ventilation of mines have all been ably analyzed and presented in previous articles. For this reason, only a resume of conditions affecting the cooling and conditioning of deep and hot mines will be given in this paper before attention is directed to possible methods of improving atmospheric conditions in the working levels.

Jan 1, 1929

By R. W. Waterfill

MANY existing ore deposits of valuable metals have been worked out in their upper surface levels and the continued productivity of these mines is dependent on their extension to greater depths in the earth. The maximum depths at present reached are about 6000 to 8000 ft. below the surface, with no evidence of an impoverished ore vein. These mines are widely distributed; some of the best known are in South Africa, Brazil, India and in the western sections of the United States. Among the factors which increase the difficulty of working these mines at increasing depths are hoisting, rock pressure and temperature. The manner and effectiveness with which these problems are met will, no doubt, determine in a large measure the ultimate depths to which any mine can be profitably worked. The most critical of these three factors at present is the increase in temperature with depth. The high temperature and humidity in many of these mines at present is severely detrimental to the health of the workers and greatly hampers their efficiency. Some have almost reached a condition in which the human system cannot survive. The problems involved in the cooling and ventilation of mines have all been ably analyzed and presented in previous articles. For this reason, only a resume of conditions affecting the cooling and conditioning of deep and hot mines will be given in this paper before attention is directed to possible methods of improving atmospheric conditions in the working levels.

Jan 1, 1929

By H. S. Greismer

Alabama washes a larger percentage of its total coal output than any state in the Union. For producing coking coal, three-compartment jigs are favored; mines providing, steam and commercial coal use single-compartment jigs exclusively. Chemists are as necessary to washing plants as recording gages are to power plants. Experiments in Alabama indicate that the sludge released by coal-washing plants can be deposited in streams and on agricultural lands without disastrous results. CAMPBELL, 1 in 1896 said: "The Birmingham district in Alabama has certain great advantages for there are few places in the world where fuel and ore are so near together, although, unfortunately, both are of inferior quality; the ore being low in iron and high in phosphorus and the coal giving a weak and impure coke." This statement could not have been, questioned in 1894, but by 1896 several Robinson-Ramsay washers had been put into operation and weak and impure coke was a thing of the past. The Warrior coal field of Alabama contains six seams that yield coking coal of excellent quality. In descending- order, they are Brookwood, Milldale, Pratt, America, Mary Lee, and Black Creek. In each of these, however, bands of rock and bone coal of varying thickness are stratified with the coal; and while some of these impurities can be separated from the coal by the miner, much of it must be loaded out with the coal: Consequently, unless the coal is washed before being coked, it will yield a coke of varying ash and sulfur content quite unsatisfactory, for blast-furnace use. At present, the Gulf States Steel Co. is producing run-of-mine coal at its Virginia mine, from the America seam, that is uniformly low enough in ash to permit of coking without washing, but this is the only exception to the above statement. Alabama was the first state to experiment seriously with coal washers, was the first to install washers on a large scale and, up to the present, has maintained the lead. The Alabama State Mine Inspector reports that during 1923 20,919,303 tons of bituminous coal were mined in Alabama; 12,858,499 tons of which were delivered to coal washers for treatment.

Jan 9, 1924

By G. Sachs

X-RAY analysis and single-crystal study have been utilized in recent years as a new means of following constitutional changes in alloys. If such transformations can be suppressed by rapid cooling, they can be followed at room temperature in a particularly convenient manner. In the following we shall consider changes in solubility and polymorphic transformations with particular reference to phenomena of the age-hardening type. Finally a thermodynamic viewpoint is developed for examining such transformations.

Jan 1, 1931

By Hewitt Wilson

IN 1903, T. M. and E. H. Alvord, of Marblemount, Wash., built a soapstone-grinding mill in the Skagit River Valley and are reported to have produced "ground talc" during 1904 and 1905, shipping to the paper mills in Wisconsin. Between 1916 and 1920, the Western Talc Co. built and operated a talc-grinding mill north of Mondovi, on the banks of the Spokane River, in eastern Washington, and sold powdered talc to the Inland Empire Paper Co. of Spokane. ? The most active develop-ment in recent years has been by two companies in the Skagit Valley-the Skagit Talc Company, Inc., which has been sawing soapstone block for the soda-recovery furnaces of the pulp and paper companies, and the Asbestos-Talc Products of Washington, Inc., at Burlington, which has been mining and dry-grinding a soft serpentine for the structural filler and insulation trade. Many prospects have been opened in the northern part of the state on both sides of the Cascade Mountains, and these activities undoubtedly are the forerunner of an industry that promises to attain considerable magnitude in the North Pacific States. At the present time, talc is imported from California for use as paper filler, and soapstone block from Virginia for use in the soda-recovery furnaces. A small market has been created locally for tailor and foundry:, pencils, stove grills, and block soapstone for art objects. The results of the present study, as yet incomplete, indicate that the use as a refractory and as a ceramic filler and flux can be expanded.

Jan 1, 1936