Search Documents

By F. R. Hensel

PuRe silver and silver-lead alloys have been studied as to their suitability for bearing~.' A review of the properties of thallium and the silver-thallium constitutional diagram was made by the author to analyze the possibilities of silver-thallium compositions for antifriction materia1s. t The silver-rich end of the diagram as reported in the literatureg-" was found to be sketchy and it was necessary to carry out corisiderable experimental work to arrive at definite conclusions. Some of the results of this work are reported in this paper. Test Materials In the beginning of the work, only fused alloys were investigated. Later, research Table i.—Composition of Fused Silver-thallium Alloys Tested for Antifriction Properties Percentage Alloy No. of Thallium 1533...................... 0.48 1534.................... 1.06 a31 HT................... 2.04 231....................... 2.10 232 HT................... 3.83 Balance 232....................... 4.07 Silver 233 HT................... 5.86 a33....................... 6.38 a34....................... 9.84 a34 HT................... 10.07 was carried out on electroplating methods and diffusion processes. In preparing the fused alloyst care was taken to exhaust the toxic fumes caused by the thaillium content. The compositions of the series of fused alloys are listed in Table I. The silver-thallium alloys were melted in clay-graphite crucibles and cast into preheated steel molds of 3/4-in, diameter. In the cast condition, they showed a cored structure, as indicated by the micrographs of Figs. I to 3. The etching reagent used was a mixture of 2 grams K2Cr207, 8 C.C. H2S04, and IOO C.C. H20. The cored structure is unsatisfactory for the type of corrosion resistance required for bearing applications, and homogenizing experiments were carried out at various temperatures, the results of which are shown in Figs. 4 through 8. The alloys with a lower thallium concentration, which were heated for 2 hr. at 525°C show an almost completely homogenized solid solution type of structure. With higher thallium concentration, the homogenizing temperature was dropped to 475OC. to eliminate the formation of a liquid phase. It is evident that heating for 2 hr. at this temperature did not iesiilt iii complete elimination of the cored structure. As would be expected, cold-working of the cast structure is an expedient in establishing equilibrium conditions. The fine homogeneous grain structure shown in Fig. 7 corresponds to the cold-worked area under the Rockwell ball penetration when the hardness was taken before heat-treatment. A detailed structural study was made on a cast silver-thallium alloy containing 3.67 per cent thallium. Three micrographs (Figs. 9, 10 and 11) show the transition

Jan 1, 1946

By F. R. Hensel

PuRe silver and silver-lead alloys have been studied as to their suitability for bearing~.' A review of the properties of thallium and the silver-thallium constitutional diagram was made by the author to analyze the possibilities of silver-thallium compositions for antifriction materia1s. t The silver-rich end of the diagram as reported in the literatureg-" was found to be sketchy and it was necessary to carry out corisiderable experimental work to arrive at definite conclusions. Some of the results of this work are reported in this paper. Test Materials In the beginning of the work, only fused alloys were investigated. Later, research Table i.—Composition of Fused Silver-thallium Alloys Tested for Antifriction Properties Percentage Alloy No. of Thallium 1533...................... 0.48 1534.................... 1.06 a31 HT................... 2.04 231....................... 2.10 232 HT................... 3.83 Balance 232....................... 4.07 Silver 233 HT................... 5.86 a33....................... 6.38 a34....................... 9.84 a34 HT................... 10.07 was carried out on electroplating methods and diffusion processes. In preparing the fused alloyst care was taken to exhaust the toxic fumes caused by the thaillium content. The compositions of the series of fused alloys are listed in Table I. The silver-thallium alloys were melted in clay-graphite crucibles and cast into preheated steel molds of 3/4-in, diameter. In the cast condition, they showed a cored structure, as indicated by the micrographs of Figs. I to 3. The etching reagent used was a mixture of 2 grams K2Cr207, 8 C.C. H2S04, and IOO C.C. H20. The cored structure is unsatisfactory for the type of corrosion resistance required for bearing applications, and homogenizing experiments were carried out at various temperatures, the results of which are shown in Figs. 4 through 8. The alloys with a lower thallium concentration, which were heated for 2 hr. at 525°C show an almost completely homogenized solid solution type of structure. With higher thallium concentration, the homogenizing temperature was dropped to 475OC. to eliminate the formation of a liquid phase. It is evident that heating for 2 hr. at this temperature did not iesiilt iii complete elimination of the cored structure. As would be expected, cold-working of the cast structure is an expedient in establishing equilibrium conditions. The fine homogeneous grain structure shown in Fig. 7 corresponds to the cold-worked area under the Rockwell ball penetration when the hardness was taken before heat-treatment. A detailed structural study was made on a cast silver-thallium alloy containing 3.67 per cent thallium. Three micrographs (Figs. 9, 10 and 11) show the transition

Jan 1, 1946

By George E. Thackray

In December, 1894, the Cambria Iron Company made a number of heats of Bessemer steel to be used in structures by one of its customers, subject to inspection and tests by a firm of consulting engineers, one of the requirements being that the material should riot exceed .08 per cent. of phosphorus. In other respects the requirements were such that they could only be met by material of good quality; but the general spe cification is not introduced here, as it is not the purpose of this paper to deal with anything except certain difficulties encoun tered in determining the phosphorus-content of the material in a manner satisfactory to both seller and buyer. Preliminary determinations of phosphorus were made in sample-ingots from each of the heats from which material was rolled for the order in question, and these preliminary chemical tests, made in the laboratory of the Cambria Iron Company, showed that, with very few exceptions, every heat was within the prescribed limit of phosphorus. After the material had been rolled, sample-drilling8 of finished material were taken from the various heats in the regular manner in use at the works, these samples being thoroughly mixed and divided into two parts, one of which was analyzed at the works' laboratory and the other sent to the inspecting engineer. Several hundred determinations were made from this mate rial without reaching an agreement between the work of the inspector's chemist and that of the works' chemist; but as it is not the object of this memorandum to treat of this part of the subject at length, it is considered sufficient to present herewith only a few of these first determinations. The analyses given in Table I. are those of the original series made on the heats which were afterwards resampled for final determination by an arbitrator; and they are selected for this reason, as the entire " comparison is thus rendered more complete.

Jan 1, 1896

By R. W. Raymond

THE absence of a convenient glossary of terns connected with mining and metallurgy has long been felt by the general public. It is to meet this want, not to furnish a technical manual for experts, that the following glossary has been prepared. It originated in an attempt on my part to revise for publication the manuscript of a compilation prepared from the appendix of Yale's work on Mining Titles and one or two other sources, to serve as an appendix to a new work on mining law, about to be published by Mr. H. N. Copp, of Washington, D. C. This revision soon assumed, contrary to my original intention, the proportions of a reconstruction ; and with the consent of Mr. Copp, and for the purpose of receiving from my fellow-members valuable aid, I presented my still incomplete work as a paper at the Lake Superior meeting of the Institute, inviting from any quarter suggestions of new terms or better definitions to be incorporated in the glossary before its final publication. This invitation was so widely and generously responded to, that I cannot undertake to make in this place' individual acknowledgments to those members of the Institute, and professional colleagues outside of it, who hays favored me with ' assistance and advice. The labor bestowed upon this paper since its presentation, at the Lake Superior meeting has considerably exceeded that of its first preparation, as

Jan 1, 1881

By H. D. Newell

THERE has been much research and commercial development in recent years in the use of chromium and nickel in steels of various types, including those intended for high-temperature service. By "high-tem-perature steels" are meant those specifically designed for service at ele-vated temperatures in steam plants, oil refineries and other industries where high-temperature operations are conducted. This paper is devoted to some preliminary data on the effect of silicon on certain of the most popular chromium-molybdenum steels now being used in quantity by the refining industry and includes a short statement on the influence of copper in steels intended for high-temperature service.

Jan 1, 1937

By Evan Just

Throughout history mining operations have, been relatively technical in character and somewhat esoteric. In ancient times mines were places where prisoners of war or criminals were sent, to drag out short lives of hard labor, under conditions ranging from hazardous to lethal. Underground mines were damp and poorly lighted, and workers were often cramped in narrow spaces and tiresome positions. Hard rock was mined by building fires against faces and quenching with water. Combustion products from these fires and from such dim torches as were provided, plus the dampness, made the underground atmospheres quite injurious to health. During the Middle Ages, mining became less penitential and more technical. Because of the desire of sovereigns to foster production from mines, miners enjoyed special privileges as free men. Crude pumping, hoisting, and ventilation systems were introduced (Fig. 9.1). However, mining remained a relatively hardworking, hazardous occupation, separated from the lives and comprehensions of most people. With the Industrial Revolution, steam-powered pumps enabled penetration to greater depths, and the use of power-driven machinery gradually revolutionized productivity. Skill became more important than back-breaking labor. This revolution continues into the present. Mining today uses some of the largest and most complicated machinery in existence and little rock is moved by direct labor. Power drills, explosives, and boring machines penetrate and break hard rock. The modern mine, surface or underground, presents an impressive panoply of drilling, breaking, loading, and transporting equipment, facilities for power transmission, pumping, and ventilation, and expensive, complicated crushing and treatment machinery. Modern technology, machinery, and skilled workmen produce an efficiency that knows no parallel in the raw material field. Mineral substances are extracted and converted into useful forms at costs which are dwarfed by those of providing forest or agricultural products in terms of comparable weights, even though conversion of these last categories is typically much simpler. Capital investment per worker, i.e., mechanization, is greater than in nearly all other industries. Despite these features, and more than average financial risk, the mineral industries perform at modest profit. The popular concept that mines and oil fields are sources of boundless rewards is a myth, sustained by the occasional unusual episode. Before one can start actual production of minerals, he must first acquire a suitable deposit. The process of acquisition will require anything from a rather simple search to a difficult, lengthy, expensive exploration effort. After locating the desired deposit, title must be obtained by denouncement, concession, leasing, or purchase. If the deposit is solid, it can be mined in pits or underground workings. If fluid or easily fusible, it can be produced through wells. If dissolved in lake or seawater, it can be

Jan 1, 1976

By Guillermo Zuloaga

THE iron deposits of the Imataca Range of Venezuela, which occur along the Orinoco River, in the northern border of the Guayana High-lands, have lately attracted attention on account of their economic possibilities. Many deposits occur in this area; some of slight economic importance and others that may rank with the largest masses of high-grade iron ore of the world. The geology and the character of the ores seem to be remarkably similar to those of the large iron deposits of Brazil. In the investigation of the Venezuelan deposits a definite relationship has been found between the mineralization of the large orebodies and igneous intrusions, especially norites and granites. The following paper is the result of a field and laboratory investigation of the ore deposits. The field work was done during the months of February and March of the year 1929, partly in the company of Prof. W. H. Newhouse. The laboratory studies have been made in the Massachusetts Institute of Technology, under the supervision of Profes-sor Lindgren and Professor Newhouse.

Jan 1, 1933

By D. G. Russell

Two techniques have been developed with which the applicability of pressure build-up analyses can be extended to include pressure data which previously have been considered virtually unusable. One of the interpretation methods makes possible the analysis of pressure build-up performance during the wellbore fill-up or after production period which occurs soon after a well is closed in. The other technique is an extension of a method for analyzing pressure build-up performance during the late-time portion of the pressure build-up which occurs after boundary eflects first begin to alter the shape of a conventional pressure build-up curve. With both of these methods it is possible to obtain estitnates of the kh product, the skin factor and the reservoir pressure. In addition, with the late-time analysis technique it is possible to obtain an estimate of the contributory drainage volume of the well being tested. This means that in some cases a check on reservoir limit test and (or) material-balance calculations can now be obtained from pressure build-ups. Both methods are slightly more time-consuming than conventional pressure build-up analysis methods because trial-and-error plots of pressure data must be made. The late-time method for analysis of pressure build-ups is in principle applicable to the late-time portion of a two-rate flow test or a pressure drawdown test. The interpretation formulas and procedures for these types of tests are also outlined. In these cases, as with pressure build-ups, it is significant that an estimate of the contributory pore volume is also obtained. On the basis of limited experience with the new techniques, it appears that satisfactory estimates of the kh product, skin factor, reservoir pressure and, for late-time analysis, contributory drainage volume can be obtained. INTRODUCTION The analysis of bottom-hole pressure build-up behavior in closed-in wells has been a a subject of interest in petroleum engineering circles for many years. In fact, few other subjects have received as much attention as pressure buildup analysis methods have. The cause for this interest is essentially twofold in nature. First, the pressure behavior of a well can normally be measured with a reasonably high degree of accuracy so that good data for analysis can be obtained. Secondly, over a fairly wide range of operating conditions, valuable information as to the quality of the reservoir rock and completion efficiency of the well can be obtained at a nominal cost. In recent years, numerous papers have been prepared on the effects of various operating conditions and reservoir heterogeneities on pressure buildup behavior. Very little work has been done, however, on extension of pressure build-up analysis methods to those pressure data which are not amenable to analysis by the present methods. The theory upon which the analysis of shut-in bottom-hole pressure build-up data is based is derived from the solution of the radial flow equation for a slightly compressible fluid for constant-rate conditions. It requires that the well be closed in for a sufficient period of time to obtain a clearly defined linear portion on the plot of observed bottom-hole pressure vs log (t + ?t)/ ?t (where At is shut-in time, and t is producing time to the instant of shut-in). From the slope of the plot and other normally obtainable data, the formation permeability, the well damage or skin factor, and the reservoir pressure at infinite shut-in time (if the reservoir were infinite) can be estimated. The successful application of this procedure depends on being able to recognize the straight-line section on the basic pressure build-up plot. The presently used pressure build-up interpretation theory also assumes that a well is closed in at the sand face and that no production into the well occurs after shut-in. In practice, of course, the well is closed in at the surface, and inflow into the well continues until the well fills sufficiently to transmit the effect of closing-in to the formation. This adjustment period is commonly referred to as the "afterproduction" or "fill-up" portion of the pressure build-up. During the period that the well fill-up effect is most pronounced, the basic pressure build-up plot is nonlinear. At later shut-in times after the effects of a drainage boundary have been felt at the well, deviation from the straight-line behavior of the pressure build-up plot also results. In many cases either of these effects or a combination of both can make the straight-line portion on the pressure build-up plot difficult to recognize. Obviously, an extension of pressure build-up analysis methods to include the afterproduction period and the period in which boundary effects are being felt would be desirable and might render valuable pressure data which for years have been considered virtually unusable. The principal reference of note concerning pressure buildup analysis during the afterproduction period is a paper by Gladfelter, Tracy and Wilsey.1 In the approach of these authors it is necessary to measure the rate of influx into the well during the afterproduction period. This is done through sonic measurements or through measurement of tubing-head and casing-head pressures simultaneously with

Jan 1, 1967

By R. L. Templin

THE increasing use of aluminum and its alloys in commercial fields has demanded a better understanding of their machining properties. This fact is exemplified by problems that have arisen in the automotive and airplane industries, but many in other fields might be cited. As pure aluminum and its alloys in their various commercial conditions show appreciable differences in their machining properties, it is not surprising that quite divergent solutions have been offered for the machining problems encountered. However, if the fundamental requirements of the most suitable cutting tools for these metals are understood, these machining problems lend themselves more readily to satisfactory solutions. Since the machining of free cutting brass and mild steel is understood by most persons accustomed to working these metals, it may serve our purpose better to first make a general comparison of the tools more commonly used in machining these metals with the tools most suitable for machining aluminum, then proceed to a more specific discussion of the individual stools.

Jan 1, 1927

By M. H. Forester, John D. Cooner

ALTHOUGH the unmined anthracite will last for approximately A 150 years, most of the thicker and cleaner coal beds have been almost entirely first-mined and pretty well robbed, leaving much of the present and future production to come from thin and dirtier beds. Herewith is a section of one of the dirty beds being mined in the Wyoming region This section shows that 45.8 per cent of the bed is made up of impurities and that the 45 in. of coal in the bed is in five benches, the thickest of which is 19 inches. In some localities of the anthracite region there are 14 beds of minable coal. Orderly and proper mining of the coal makes it necessary to rob or second-mine-almost all beds have already been first-mined-in sequence from the top downward. Therefore the robbing of the few remaining portions of the thicker and cleaner beds is in many instances being held up by the mining of the overlying thin and dirtier coal beds. Impurities Impurities consist of fire clay, slate, rock, and bone. The latter, which is black, contains 40 to 60 per cent carbon and often resembles good coal. In some beds there are also bands of "blue" coal, which, as the name implies, is of a bluish slaty color. Although much of this "blue" coal has a carban content almost as high as the good anthracite, it is not

Jan 1, 1943

By Robert Mehl

THE importance of the Widmanstätten structure to structure theory in metallography has been recognized by many writers.1 It is a structure produced by the precipitation of a new phase from a solid solution upon cooling as a result of changing solid solubility, and displays a characteristic appearance indicating a crystallographic relationship between the new phase and the original solid solution (Fig. 1). First discovered in 1808 by Alois de Widmanstätten2, the structure has been traced by analogy through many alloy systems. Particularly is this true of the steels. Sorby's classic work3 on the microstructure of iron and steel was in essence an attempt to explain the origin of this characteristic structure in meteoric iron. He observed in a Bessemer steel and in a cast-steel ingot structures which we now recognize as typical Widmanstätten figures.4 Osmond5 observed structures in a steel ingot analogous to those found in meteorites. Arnold and McWilliams6 obtained (and recognized) a

Jan 1, 1930

By Y. L. Yao

The solubility limit of oxygeu in a titanionn at 850°C has been determined by magnetic measurements as 12.5 + 0.5 pct (29.0—30,9 at. pct). Also in the susceptibility-co~centmtion curve, there is n distinct but not sharp maximum at 19.0 * 0.5 z~t pet (40.5--42.1 at. pct), which indicates the presence of the 6 phase. The magnetic susceptibilities of the alloys of the titanium-oxygen system were determined byEhrlich in 1939.' is alloys were prepared by sintiring mixtures of titanium and its oxide at high temperatures. On the titanium-rich side, despite the fact that the alloy compositions he measured crossed two phase boundaries, the limited results obtained

Jan 1, 1960

By Robert N. McIndoo, M. G. Woodle

10.5-1. Introduction. In the not-too-distant past, maintenance and the facilities for maintenance were considered a necessary evil to be given only secondary consideration in the development and planning of a surface mine operation. With the increasing sophistication of mining equipment and machinery, this concept has been replaced; and today's mine managers recognize that planning for adequate maintenance facilities is as important to a successful operation as a sound mining plan. This chapter will present the basic maintenance facilities and the fundamental considerations necessary to meet the varied requirements of surface mining. 10.5-2. Determination of Shop Facilities. The size, shape, and extent of maintenance facilities are contingent on the general mining plan, the location relative to outside facilities, and to the available capital. The type of construction employed is dependent on climatic conditions and preference. HAULAGE SYSTEMS. The type of haulage equipment used will dictate the kind of shops needed. Truck haulage requires entirely different facilities than rail haulage. Some mines will employ both systems, and can include hoists, skips, or conveyor belts in combination with locomotives or trucks. The requirements of each type will be discussed. MAINTENANCE ORGANIZATION. The pre-planning decision as to centralized maintenance vs. area maintenance, or a combination of both, will greatly affect the maintenance facilities required. A single pit with relatively short travel from shops to pit will probably have a centralized maintenance system. Where more than one mine is involved, or where there are diversified sections or functions in a mine (mine equipment, mill, conveyor, or

Jan 1, 1968

By C. C. Furnas

IT is well known that particles of different sizes are not distributed evenly throughout the average charge in an iron blast furnace. Just how great the disparity in particle size in different parts of a single plane in a furnace may be is indicated by the results of some recent investigations1 conducted by the Bureau of Mines on a furnace operating on Lake ores. The wide variations found in gas velocity, gas composition, and temperature from the periphery to the center of the upper charge column were caused by the great variation in particle size of the raw materials used and were also greatly influenced by the methods of charging. This paper summarizes the results of an investigation of the influence of different methods of charging and of the treatment of raw materials upon the size distribution of the solid particles in the blast furnace. A more complete report will appear later as a Bureau of Mines technical paper.

Jan 1, 1929

By Frederick Laist

Introduction IN a leaching process, having obtained the copper in solution, the choice of the precipitation method is influenced y the following factors: 1. Availability of precipitant. 2. Adaptability to the leaching process. 3. Final product desired. 4. Regeneration of leaching solutions. 5. Fouling of solutions. There are three general classes of precipitation methods: 1. The use of iron, scrap or sponge. 2. Electrolytic deposition. 3. The use of some gas or reagent y which the copper is obtained, usually in the form of an intermediate precipitate which requires further treatment. For example, the precipitation of the copper as Cu2Cl2 from chloride solutions, with SO2 gas. The use of iron is adapted to almost any process. It has the great advantage of extreme simplicity, and the recovery of the copper and any values present in a highly concentrated, easily treatable form. The disadvantages are the cost in isolated places, the uncertainty of the scrap-iron market, and the fouling of the leaching solutions. The latter is a serious factor, When a reagent such as salt is used in them, which makes necessary their re-use. Where applicable, electrolytic deposition is very attractive. The copper is obtained in a form directly marketable, there is a regeneration of acid amid no fouling of solutions. Unfortunately, chloride solutions do not lend themselves to electrolysis. An entirely satisfactory anode material has not yet been discovered, although magnetite, apart from being rather brittle, seems to answer the requirements fairly Well.

Jan 7, 1914

By W. R. Hibbard, Ming-Kao Yen

Various rationalizations of preferred orientations in cold worked polycrystalline metals have been based on the operation of at least two three2 five, an indefinite number, and all,6 slip systems of the type occurring in single crystals. Pickus and Mathewson3 suggested that the cold rolling texture in face-centered cubic metals could be rationalized on the basis of two or more operating slip directions symmetrically disposed about the direction of flow in such a manner that the resolved shear stress factor is equal for all operating slip systems and lattice rotations cancel each other. The importance of the direction of flow, the necessity for the operation of slip systems capable of producing the required changes in external dimensions, the maintenance of a common surface between adjacent grains and a symmetrical arrangement of the operating slip systems in order to produce an end orientation which is stable under additional deformation lead to the following rationalization of textures based on the type of slip systems operative in single crystals. The rationalization is intended to explain why certain orientations are suitable for deformational flow without a change in orientation and thus are stable end orientations or ideal texture orientations. It does not attempt to explain how the grains of a randomly oriented polycrystalline aggregate will reach this orientation. The rationalization is based on the following four postulates: 1. The ideal textures for polycrystalline aggregates are the result of reorientations of individual crystals toward the same stable end orientation at which no further reorientation will occur even during additional deformation. Since, in simple slip, the relative orientations of the stress axis and the active slip system determine the change in orientation during slip, it is considered that the orientation of the stress axis with respect to the ideal texture determines what slip systems must be active to retain the stable end orientation. Therefore the stable end orientation should be a symmetrical one around the stress axis with respect to the active slip systems such that lattice rotations resulting from slip will cancel each other and prevent a resultant change in orientation. (Rotational symmetry only—not translation, inversion, nor others—is considered here.) Thus a metal under a pure stress should develop a texture consisting of one or more of the crystallographically symmetrical directions, <100>, <110> or <111> for cubic metals or <0001>, <1010> or <1120> for hexagonal close-packed metals, parallel to the stress axis. 2. Since the active slip direction is the direction of glide during simple slip and thus the direction of maximum shear movement, in the ideal texture the active slip

Jan 1, 1949

By Ming-Kao Yen, W. R. Hibbard

Various rationalizations of preferred orientations in cold worked polycrystalline metals have been based on the operation of at least two three2 five, an indefinite number, and all,6 slip systems of the type occurring in single crystals. Pickus and Mathewson3 suggested that the cold rolling texture in face-centered cubic metals could be rationalized on the basis of two or more operating slip directions symmetrically disposed about the direction of flow in such a manner that the resolved shear stress factor is equal for all operating slip systems and lattice rotations cancel each other. The importance of the direction of flow, the necessity for the operation of slip systems capable of producing the required changes in external dimensions, the maintenance of a common surface between adjacent grains and a symmetrical arrangement of the operating slip systems in order to produce an end orientation which is stable under additional deformation lead to the following rationalization of textures based on the type of slip systems operative in single crystals. The rationalization is intended to explain why certain orientations are suitable for deformational flow without a change in orientation and thus are stable end orientations or ideal texture orientations. It does not attempt to explain how the grains of a randomly oriented polycrystalline aggregate will reach this orientation. The rationalization is based on the following four postulates: 1. The ideal textures for polycrystalline aggregates are the result of reorientations of individual crystals toward the same stable end orientation at which no further reorientation will occur even during additional deformation. Since, in simple slip, the relative orientations of the stress axis and the active slip system determine the change in orientation during slip, it is considered that the orientation of the stress axis with respect to the ideal texture determines what slip systems must be active to retain the stable end orientation. Therefore the stable end orientation should be a symmetrical one around the stress axis with respect to the active slip systems such that lattice rotations resulting from slip will cancel each other and prevent a resultant change in orientation. (Rotational symmetry only—not translation, inversion, nor others—is considered here.) Thus a metal under a pure stress should develop a texture consisting of one or more of the crystallographically symmetrical directions, <100>, <110> or <111> for cubic metals or <0001>, <1010> or <1120> for hexagonal close-packed metals, parallel to the stress axis. 2. Since the active slip direction is the direction of glide during simple slip and thus the direction of maximum shear movement, in the ideal texture the active slip

Jan 1, 1949

By C. E. Lesher

Low-temPeRatUre carbonization needs no introduction to the literature on coal. This paper will attempt no review of that literature; it tells the story of the commercial development of one of the processes for carbonizing coal at so-called low temperatures, dealing with the technology and economics of the process rather than with the design of equipment. The process used is that covered by the patents of C. B. Wisner, with improvements and changes made by the Pittsburgh Coal Carbonization Co. The important and novel feature of the process is the phenomenon of making the product in ball form (Fig. 1). Melting coal dust into smokeless solid fuel in an apparatus as simple as a revolving cylinder of ordinary mild steel has been proved to be practical. Furthermore, it has been found that the process has a wide application, for by applying a knowledge of why and how this balling action is accomplished, the apparatus can be designed and adapted to treat any coal that has a certain minimum agglutinating property. The operating plant is 20 miles west of Pittsburgh, adjacent to the Champion preparation plant of the Pittsburgh Coal Co. The coal used is cleaned minus ?-in. or finer sizes. The products are low-tem-perature coke, tar and tar products. Present capacity is 7000 tons per month of low-temperature coke and 140,000 gal. of tar. There is no surplus gas for sale, and none of the light oils are stripped from the gas. The coke is marketed in two sizes, 1 to 2 in. and 1 to 6 in., through retail coal dealers for domestic consumption in hand-fired furnaces, and for fireplace fuel. The smaller size is bagged by dealers. Crude tar and many distillates and road tars are sold. Acknowledgments During the 10 years in which the work that is summarized in this paper has been under way, many have contributed time and effort, faithful service and fruitful thinking. Whatever success has attended

Jan 1, 1940

By C. E. Lesher

Low-temPeRatUre carbonization needs no introduction to the literature on coal. This paper will attempt no review of that literature; it tells the story of the commercial development of one of the processes for carbonizing coal at so-called low temperatures, dealing with the technology and economics of the process rather than with the design of equipment. The process used is that covered by the patents of C. B. Wisner, with improvements and changes made by the Pittsburgh Coal Carbonization Co. The important and novel feature of the process is the phenomenon of making the product in ball form (Fig. 1). Melting coal dust into smokeless solid fuel in an apparatus as simple as a revolving cylinder of ordinary mild steel has been proved to be practical. Furthermore, it has been found that the process has a wide application, for by applying a knowledge of why and how this balling action is accomplished, the apparatus can be designed and adapted to treat any coal that has a certain minimum agglutinating property. The operating plant is 20 miles west of Pittsburgh, adjacent to the Champion preparation plant of the Pittsburgh Coal Co. The coal used is cleaned minus ?-in. or finer sizes. The products are low-tem-perature coke, tar and tar products. Present capacity is 7000 tons per month of low-temperature coke and 140,000 gal. of tar. There is no surplus gas for sale, and none of the light oils are stripped from the gas. The coke is marketed in two sizes, 1 to 2 in. and 1 to 6 in., through retail coal dealers for domestic consumption in hand-fired furnaces, and for fireplace fuel. The smaller size is bagged by dealers. Crude tar and many distillates and road tars are sold. Acknowledgments During the 10 years in which the work that is summarized in this paper has been under way, many have contributed time and effort, faithful service and fruitful thinking. Whatever success has attended

Jan 1, 1940

By Jack A. Simon, M. E. Hopkins

Coal is defined as a combustible rock that originated in the accumulation and physical and chemical alteration of vegetation. Coal can be ignited and burned like the wood that was man&apos;s earliest fuel, but coal gives more heat than the same amount of wood and has many industrial uses. Unlike wood, coal is not generally found on the surface of the ground but is mined from the solid rock of the earth. Before taking up the occurrence, formation, and the unique character of coal in the rock sequence, let us briefly consider the general character of all rocks in the crust of the earth. Relatively little is known about the very earliest history of the earth, although a number of logical theories have been developed. Manned exploration of the moon and the rocks returned to earth continue to provide some answers to questions concerning the earth&apos;s origin and history. The period of earth history with which we concern ourselves here begins after great areas of water had evolved on earth and substantial land areas of once molten (igneous) rock existed. Weathering and other processes that attacked the surface of the rocks reduced them to small particles. Water provided by rainfall transported this material, ultimately, to large bodies of water where it was deposited. Thus was initiated the geologic sequence of sedimentary rocks that lie above the once molten igneous rocks. The crust and upper mantle of the earth are made up of several large plates along which differential movement (primarily horizontal) takes place. Such movements, although small, are occurring today. These horizontal movements are accompanied by vertical movements causing important changes in the relative position of the continents and oceans. Low-lying coastal swamps with favorable climates are ideal locations for coal accumulation and burial by river-borne sediments, and large areas

Jan 1, 1981