Search Documents

By Edward H. Robie

SUBJECT to formal Board approval in September, AIME dues will continue indefinitely at the present scale of $20 for Members and Associate Members; and $12 for Junior Members for the first six years of such membership, thereafter $17. That is the wish of the Board of Directors and the will of the membership, as expressed in the recent referendum. Though the official returns, as reported by the tellers, are not available as this is written, the data are sufficiently complete to give the results to the nearest percent. The total vote was approximately 93 pct for continuance of the present scale. Metals Branch members voted about 94 pet for continuance; Mining Branch members slightly less than that; and Petroleum Branch members about 91 pct. As in the referendum of 1949, there was no particular difference of opinion on the question of dues as between the three Branches. The percentage of ballots returned was about 61 pct, only slightly more than in the 1949 referendum. But the affirmative vote was much greater, 93 pct against 78 pet in the earlier referendum. Looked at another way, a majority of those to whom ballots were sent, 56 pct, voted to continue the present scale of dues, whereas only 46 1/2 pct of those canvassed voted to raise the dues in the previous referendum. But approximately 600 , members expressed their opinion that the dues should go back to $15 for Members and Associate Members and to $10 and $15 for Junior Members. This is a substantial group of members who either do not think they are getting their money's worth from AIME membership, or believe that a more businesslike conduct of Institute affairs should provide current services at less cost, or believe that more service is being provided for their dues than they need. As to the first point, it is probable that some members are not getting their money's worth. They perhaps have only a fringe interest in. AIME activities, or they do not or cannot participate in such activities at the Local Section, divisional, or national level, so that all they get out of the Institute is the monthly journal, which they do not have time to read. If they did read it intelligently, and acted upon the professional information thus gained, it is difficult to understand how one or more ideas cannot be gained that would be worth $20 to them professionally. But the 600 members who want lower dues offer a challenge to the Directors and to the staff to do a better job; to make Institute membership so rewarding that every. member will be thoroughly satisfied. Twenty 1935 to 1939 dollars are worth only $11.60 now, according to the latest government data, but that makes it all the more necessary for us all to appraise the value of what we buy. To the 93 pct of Institute members who expressed a vote of confidence, so to speak, the staff, and we feel sure the Directors as well, are most appreciative and thankful.

Jan 1, 1952

By -1ng. B. Stampa

Introduction The author investigates the technology available for mine flow reversibility by reversing the operation of the main fans. Air bypassing, reversed sense of impeller rotation, and blade angle overturning are indentified as the most important means of achieving the flow reversibility. The axial flow fan is studied in some detail and the important variables of fan capacity, pressure, and efficiency are compared. Although some references to rotor velocity vectors are made (Fig. 1) the subject is not presented in detail in order to stay within the paper's intent. Background Where applicable, the requirements of mine air reversibility are an important part of the overall mining operation and should be given proper attention during mine ventilation design. The need for preventing mine fires in intake shafts is the reason that, for a long time, it has been a requirement in the Eastern European countries to have the feature of flow reversibility built into all main mine ventilators. In West German coal mines, this requirement does not apply since higher priority is given to safety precautions. Some metal and mineral mines in the United States are required to have ventilation currents readily reversible in order to fight underground fires as stipulated by the Title 30, Mineral Resources, and by the mining laws of some states. From an equipment performance standpoint, assuming the validity of other flow technical data, the question of the ventilator flow reversibility is of ten related to the actual scenario of the begining of an emergency. Most of the time, the system operates within half of the design capacity only and assuming that the equivalent mine orifice is stable only a quarter of the design pressure must be produced by the fan in any event. For such an operating point, the effective gradient and energy losses can be disregarded since fire emergencies usually last for only a short period of time. Equipment Comparison Fig. 2 depicts a ventilation arrangement wherein the flow can be reversed through changing the functional position of the dampers (slideplate or blade type). Both axial or radial fans can be applied in this case. For the mine exhaust operation, slide plates (guillotines) I and I11 are opened while plates I1 and IV are closed. The flow thus encounters two reroutings, which due to the reverse ventilation flow cannot be equipped with proper sheet metal deflectors, and therefore large pressure losses result during the air reroute operation. When the intake operation is considered, the dampers I and I11 are closed and the pair I1 and IV is opened. For this arrangement, almost the same flow conditions exist as for the foregoing exhaust mode; however, one additional corner must be applied. Even if a highly efficient ventilator is used in one of the previously described systems, the additional pressure losses resulting from air rerouting plus those encountered between the planes "0" and "00" significantly affect the overall energy requirements. Illustrated in Table 1 are the relative component losses of even flows for evaluation of various detour arrangements. From the aerodynamics standpoint, when these components are being designed, serious consideration must be given to the individual levels of the pressure loss coefficient, 5. Should there be an increase in the sum of the loss coefficients due to the particular component selection such that, for example, the net change is 1.2; the resulting pressure to be produced by the fan can be calculated from:

Jan 1, 1981

By Evert Hoek

Summarising a conference is never an easy task, but I will try to keep my comments brief and to the point. There are a number of lessons which we have learned from our deliberations together during these past three days, and I will try to give you my impressions of these lessons and of their practical implications in open pit mining. The first thing that has become increasingly obvious during these discussions is that it is no longer acceptable to offer an 'Act of God' as an excuse for a major slope or tailings dam failure. Disasters such as that at Aberfan in the United Kingdom have focussed the world's attention on the activities of the mining industry and the report of the commission set up to investigate the Aberfan disaster clearly showed that adequate knowledge was available and that failure to apply this knowledge did not qualify as an 'Act of God'. The courts and the world's press are certain to impose increasingly harsher penalties and criticism on those held responsible for major failures, particularly of tailings dams, in the future. One of the major problems in applying available knowledge to slope problems is that attempts to apply this knowledge are frequently left too late. To provide an engineering solution in the case of a slope in an advanced state of failure is an almost impossible task, and it is essential that those responsible for the stability of a slope must learn to recognise signs of distress at an early enough stage for effective remedial measures to be taken. As our ability to solve slope problems improves, the time at which slope stability problems are considered in a mining project must move forward to a stage at which these problems can be anticipated and dealt with before they arise. Conferences such as this are important in that they enable us to exchange ideas and advance our knowledge to a level at which such predictive engineering will be possible. It has been encouraging to hear of mining projects such as the Bougainville Copper operation where slope stability studies were carried out as part of the overall evaluation programme and it is hoped that this will become a more common procedure in the future. Providing a safe slope in an opencast mine obviously costs money, either in terms of the reduced ore to waste ratio given by flat slopes or because of the cost of stabilization techniques such as drainage or the use of rock anchors. An optimum slope design will provide maximum safety at minimum cost but achieving this optimum is not an easy task. Any one of us could design a slope which would be stable to the end of time, but it is probable that that slope would be so flat as to be totally uneconomic in most open pit mining situations. On the other hand, if the overall economics of a mining project are so critical as to require slope angles which the engineer responsible for these slopes considers to be unsafe, it is his duty to make us could design a slope which would be stable to the end of time, but it is probable that that slope would be so flat as to be totally uneconomic in most open pit mining situations. On the other hand, if the overall economics of a mining project are so critical as to require slope angles which the engineer responsible for these slopes considers to be unsafe, it is his duty to make

Jan 1, 1971

TO THE. BOARD OF DIRECTORS AND MEMBERS OF THE AMERICAN INSTITUTE OF MINING AND METALLURGICAL ENGINEERS GENTLEMEN Submitted herewith are the report of the Treasurer for the year 1945 and reports for the same year of the following committees: Membership, Admissions, Papers and Publications, Mining and Metallury (Magazine), and Library. In this review of the year by the Secretary reference frequently will be made to the "Paul" Committee and to the "hotter" Committee. The first is the special committee on Divisional Relationships and the second the special Committee on Ways and Means. These two important committees, appointed by President Harvey S. Mudd under authorization of the Board of Directors on March 21, 1945, were composed as follows:

Jan 1, 1946

By R. V. Ramani, Christopher J. Bise, Robert Stefanko

Over 200 billion tons of coal reserves lie locked up in deposits west of the Mississippi River-and of this, well over 100 billion tons are recoverable only by underground mining methods. Yet, because of the associated problems of unfavorable economics and inadequate technology, western underground mines contribute less than 2% to the annual US coal production. In order to reach the billion-ton coal production level called for by President Carter, it a pears the majority of new coal development will come from the West. But for this to be possible, new mining methods and equipment must be designed to match the unique thick seam conditions.

Jan 10, 1977

By Henry P. Chandler

Tripoli is the general name for a number of fine-grained, lightweight, friable, minutely porous, forms of decomposed siliceous rock, probably derived from siliceous limestones or calcareous cherts. Tripoli is often confused, both in the trade and technical literature, with tripolite, a diatomaceous earth (diatomite), found in Tripoli, North Africa. A material found near Seneca, Mo., resembling tripolite was incorrectly termed "tripoli." This name has persisted and now has a definite physical and trade meaning. However, tripoli contains no diatoms, is of an entirely different origin, and has chemical and physical properties different from those of tripolite. There are two distinct types of tripoli in the United States; that from the Missouri-Oklahoma field and that from the Southern Illinois field. Commercially the term "tripoli" is applied to the material from the Missouri-Oklahoma field, while the material from the Southern Illinois area is often referred to as "amorphous" or "soft" silica. Material similar to the Missouri-Oklahoma tripoli, but finer grained, occurs in northwestern Arkansas. In its Minerals Yearbook the Federal Bureau of Mines groups statistically under "natural silica abrasives," tripoli from these producing areas and rottenstone from Pennsylvania. The justification for this grouping is the similarity of use. Composition and Physical Properties Commercial tripoli contains 97 to 99 pet SiO2. The remainder is mostly alumina, iron, lime, soda, and potash, some of which may impart desirable physical properties to the material. Variations in the chemical composition of tripoli are not as important as its physical characteristics. The color of tripoli varies from white to cream, brown, rose, and red, the variations from white being the result of iron deposited from percolating surface waters. The commercial varieties of tripoli mined in the Missouri-Oklahoma area are designated as cream and rose. Other physical properties of the tripoli from this area are: Free quartz, less than 0.5 pct; oil absorption, 50.71 to 53.14 pct; water absorption of the crude tripoli, about 38 pct, and of prepared material, about 52 pct; fracture, uneven to conchoidal; specific gravity, 2.15 to 2.62; weight per cubic foot crude, 35 lb, ground, 55 lb; fusion point, 3,225° to 3,300°F; and refractive index, 1.54. Tripoli occupies about 1 cu yd to the short ton in place and about 1.5 cu yd when broken. Packed for shipment, the powdered material occupies about 33 cu ft to the ton. Its value and usefulness depend primarily on a low content of crystalline silica, size of the natural particles, absorption, and color. Some beds in the Missouri-Oklahoma area are of sufficiently compact material that large, fairly strong blocks may be removed. These find a market as filter blocks and have been used for building material. In the Southern Illinois field the color of the material is the important physical property; pure white is preferred. The rottenstone mined in Pennsylvania is of higher density and lower in silica content than the various types of tripoli. Its composition approximates 60 pct silica, 18 pct alumina, 9 pct iron oxide, 8 pct alkalies, with small amounts of lime and magnesia. The material apparently is a ferruginous and siliceous shale, having properties rendering it suitable as an abrasive or as a filter for paint, rubber, and plastics.

Jan 1, 1960

By J. Buchwald, R. W. Heckel

THE DeHoff method' of analysis of ellipsoids of constant shape provides a quantitative metallo-graphic technique whereby the actual size distribution of the ellipsoids may be determined from polished and etched random planar sections. This method provides a useful metallographic tool since it appears to be the only method available for determining the size distribution of nonequiaxed second-phase particles. This method, however, assumes that the type of particle being studied is known to be either oblate or prolate of a fixed minor to major axis ratio, q. This, in general, means that one assumes either oblate or prolate ellipsoids of a given q and checks the total volume and surface area of the second phase as determined from the particle size distribution to values of these quantities determined by other techniques. Suitable check methods may be point counting, lineal fraction, and areal fraction methods for obtaining the total volume and the Smith and Guttman2 method of intercepts for obtaining the total surface area. If the initial guess at particle shape and q were incorrect, i.c., the volume and surface information obtained from the particle size distribution data does not agree with those values obtained by other techniques, another assumption must be made and the particle size dist distribution must be recalculated. A current study in this laboratory has involved a large number of these calculations. To facilitate the handling of the calculations, the DeHoff method was programmed in the FORTRAN language for an IBM 1620 computer. The purpose of this note is to briefly describe this program. The complete program along with a list of variable names, a sample input, and a sample output may be obtained from the senior author. Basically, the program provides for the calculation of particle size distributions for a series of q values for both oblate and prolate ellipsoids for each set of input data. The total volume of second-phase particles per unit volume are calculated for each calculated particle size distribution. The output of the program is arranged to allow a rapid comparison of the calculated volume and surface values to data obtained by independent check measurements. A condensed flow chart of the program in the notation of DeHoff1 is given in Fig. 1 The calculation of the number of particles per unit volume in the jth size class, Ni, according to the DeHoff method' is: where k(q) is the shape-correction factor given by DeHoff as a function of q for both oblate and prolate ellipsoids, A is the size-class increment, k is the number of size classes, ni is the number of particles in the ith class on the planar measurement surface, and B(j,i) are the saltykov3 coefficients which correct for measurement surfaces which do not pass through the major and minor axes of the particles. The values of /3(j,i) are included as a two-dimensional array in the program. Particular values of k(q) are included in the program in increments of q of 0.05. The first calculation is carried out for q = 1 (spheres), the second for q = 0.95 oblate, the third for q = 0.95 prolate, and so forth. The number of q values chosen for the calculation is determined by a control card in the input for each set of data.

Jan 1, 1965

W. H. Blauvelt, New York, N. Y.—One thought lias been running through my mind during the wholc of this meeting and that is that the scientific and the practical men must recognize very clearly their interdependence. The value of scientific classification of coal is going to be of the very greatest importance to the users, the practical men. Is not the scientific investigation and the great amount of work that is being done in a measure at least lost to the world? Therefore the scientific investigations and the practical needs of the users should bo brought as close together, and the work should be done as closely together, as possible; that is, the scientific man should know what the practical man needs, and the practical man should not feel that the scientific man is merely a theorist. Scientific investigation is going to have a great effeet and be of great valuc to the practical man who is trying to solve his problems. In the subject which I discussed' for instance, we must look to the scientific man to tell us why coal cokes in one way and not In another and why certain coals will do certain things and others, which appear on the surfacc to be generally similar, do not act in the same way. Need or Physical Data on Coal H. J. Rose, Pittsburgh, Pa.—There is a subject which is a sort of hobby of mine; that is, the need for what might be called critical tables of constants for coal. The chemist has big volumes giving constants, such as the density, solubility, specific heat, thermal conductivity and all other physical and chemical data that have been determined for chemical compounds. Data arc also available on many common materials, for example, the density, hardness, modulus of rupture or maximum crushing strength of swamp white oak as compared with some other wood. In fact, physical data for practically cvery hype of wood commercially produced in the world can he found. In the same way the metallurgical man has handbooks giving the properties of alloys, etc., but we havc very little tabulated information about coal. Our principal reference works are the volumes published by the U. S. Bureau of Mines on the proximatc and ultimate analysis and calorific values of coals of the United States. That is 3 pioncer work of enormous value, but we have reached the point where we need more diversified information. Mr. Fulweiler raised the question of the relative strength of the different coals and cokes. Dr. Campbell and Dr. Ashley wanted to have some information on the resistance of coal to air slacking. It was brought out in the discussion that we want to know something about the coking properties of coal. There are any number of physical tests that we need, such as the thermal conductivity of certain coals, the coefficient of expansion, or the coefficient of friction; or other constants. A smattering of such information is scattered through the literature; for instance, a research worker in Wales will report a coefficient of expansion on Wclsh coals and one in South Africa will report something else for one or two kinds of African coals, hut it is difficult to find the information that is needed on our own coals. Would it not be worth while to consider collecting reliable critical

Jan 1, 1930

By Thomas P. Bispham

INTRODUCTION From the lender's point of view, the greatest period of risk in a project financing occurs during the construction phase. Therefore, most projects are supported during this phase by completion guarantees supplied by some credit-worthy entity; for example, the project sponsors in the case of a joint venture, such as that of W.R. Grace, Hanna Mining, and Liberty Capital; or by a strong contract with a utility or foreign importer/investor, such as the way North American Coal Corporation has structured many of its transactions. THE PROJECT LOAN REQUEST A project financing is a more complex form of term loan than one using an ongoing corporation's balance sheet as a credit base and, therefore, a potential lender will subject the loan request to a more rigorous analysis. To support this effort, the financial institution will require a more detailed information memorandum to evaluate the credit and technical risks of a project - especially since much of the necessary information is not otherwise available. (See also Gibbs and Sroka paper above in this Chapter) A well-prepared information memorandum will impress prospective lenders with the planning ability and general competence of management. Also, the process of preparing the memorandum will help management understand the true extent of the opportunities and limitations of its venture. Appendix A outlines the topics which comprise a complete information memorandum for a loan request. Of some interest to those seeking to sell a currently-operating mining venture, a similar information memorandum should be prepared i.e., covering the same topics discussed here, for the investment banker to use with potential purchasers. For that purpose, though, one might not want to prepare quite as much detail as for a lender. Appendix B outlines the elements of a reserve evaluation and feasibility study, often called the "Bankable Document." Usually, these studies are prepared by independent engineering consultants for use by potential borrowers and sellers. (Potential purchasers will often contract for a similar study for their use in evaluating an acquisition.) ELEMENTS OF A LOAN INFORMATION MEMORANDUM 1. Outline: The information memorandum should begin with a one-page outline covering such topics as: a. The borrower's name, address, and phone number. b. Principal contact at the borrower. c. Amount of the proposed financing. d. Desired pricing and structure of the proposed financing. This should include a description of the amount and source of equity in the proposed financing. e. Use of the proceeds and timing. 2. Summary: The most important information contained in the memorandum should be summarized in two pages. Note - If the borrower is a recently-formed single-purpose company, then elements 3, 4, and 5 will apply to the guarantors of completion and to the project sponsors. 3. The Borrower: This section is a brief biography of the borrower including such topics as date and state of incorporation, founder(s), lines of business, etc. 4. Capitalization: The borrower's current debt and equity position, including leases and trade debt, with amounts, terms, names, and addresses enumerated. Equity owners, and percentage ownership, should be identified. 5. Historical Financial Statements: If available, a minimum of five year's worth of complete historical financial statements

Jan 1, 1985

By W. P. Frey

The briquet plant of the Lehigh Coal and Navigation Co., at Lansford, Pa., has previously been referred to.' It has passed the stage of experiment and now rests on a foundation practically and financially sound. The purpose of this' paper is to explain how success has been attained, and to set standards for the development of hard-coal briquetting which may eliminate future failures. All the conclusions are based on actual results, avoiding speculation and theory. Up to three years ago, the L. C. & N. Co. used coal-tar pitch as a binder in making hard-coal briquets. The plant operated with a monthly output of 300 to 600 tons and was unable to meet its own expenses. Naturally, no one was satisfied, especially as the ideals of a smokeless briquet were still unrealized. Then came the Dutch oil process, introduced in this country by the General Briquetting Co. of New York. This process uses as binder a small percentage of heavy residue of petroleum, which, being liquid, permits great economy of handling; it also did away with the most objectionable fumes of the former briquets. This oil2 is not absolutely smokeless; heating the fresh fuel to red heat liberates some low-volatile hydrocarbons, yielding a white smoke which is not objectionable. On the other hand, this oil adds to the briquet about 7 per cent. of volatile matter, giving the product a heating capacity equal to that of the best free-burning anthracite coal. The average silt used in the manufacture of these boulets averages 16.5 per cent. chemical ash, corresponding to 12,000 B.t.u. per pound of coal. The Hydrolene used as binder runs about 17,500 B.t.u. per pound, and approximately 7 per cent. of it enters into the mixture, hence 12,000 X 0.93..........................11,160 B.t.n. 17,500 X 0.07.......................... 1,125 B.t.u. Total.....................................12,385 B.t.u. per pound of briquets

Jan 1, 1918

By N. K. Chen, R. Maddin

Columbium single crystals were deformed in tension and compression. Reorientation by X-rays and stereographic projections of slip traces indicate that plane of slip may be considered as (110). The plastic behavior is shown to be quite similar to the deformation of molybdenum single crystals. STUDIES on the crystallography of the deformation process in body-centered cubic metals have been renewed recently with investigations of iron single crystals1-" and molybdenum single crystals.4 It is now apparent that too many exceptions to the rationalization based upon the ratio of absolute testing temperature to absolute melting point by Andrade5 exist to permit more serious discussion of this type of analysis. The considerations of resolved shear stress utilizing only planes of the type {ll0}, {112), and {123)³,6 permit analysis of the deformation only on the basis of those three types of planes. The suggestions made by Elam7 and by Greninger8 in which the slip process is envisioned as a composite slip on two nonparallel {110) planes can be illustrated schematically in Fig. 1. It may be seen that an unresolved trace on any plane containing a <111> direction may be accomplished by varying the number of atoms participating in the composite process. By further varying the number of atoms in each plane but keeping the ratio of participating atoms constant, jogs could be obtained in the traces and hence wavy slip lines could be produced. Vogel and Brick&apos; studied the behavior of a iron single crystals in which they suggest that the plane of glide is "non-crystallographic" and may be predicted from the intersection between the great circle joining the slip direction and specimen axis with the great circle whose zone axis is the slip direction. In a more recent investigation on iron single crystals, Steijn and Brick" suggest that the slip mechanism may be considered as made up of a type of composite slip occurring on {110} and {112} planes. Evidence for a possible composite nature of the slip process has been presented for the case of molybdenum in the form of analysis of asterism and specimen axis rotation." Definite proof of a composite slip process must, however, await good electron microscopic resolution of the individual traces making up the unresolved optical trace used in determining the acting slip plane. The present investigation was undertaken to study the behavior of columbium single crystals not only in tension but also in compression since the specimen axis migration should indicate the plane or planes of glide in the same manner that the specimen axis migration in tension indicates the direction of glide. The orientations of eleven crystals investigated are shown in Fig. 2. Specific orientations are missing (those in the vicinity of [Ill] and [001] and consequently the effect of orientation on the crystallography of deformation could not be considered. Experimental Procedure The 1/8 in. rods (7 in. long) were subjected to an axial tension in vacuo while at temperatures in the vicinity of 2000°C for 2 to 4 hr. This treatment resulted in large cylindrical grains (about ½ in. long) occupying the entire cross section. A number of these rods were used for the tension studies by observing the behavior of the individual grains. For the compression studies, single crystals approximately % in. long by 1/8 in. in diameter were cut from the rods; the ends were ground parallel. All specimens were polished electrolytically in a solution of 15 cc HF(48 pct) and 85 cc H2SO4 (concentrated) using a platinum cathode, a current density of 0.04 amp per sq cm and a temperature between 25" and 60°C.10 Orientations were obtained using a Laue back-reflection method (3 cm film to specimen distance) with a ½ mm collimator 9 cm long. For the compression specimens, a reference mark was scratched on one of the compression sur-

Jan 1, 1954

By H. A. Shaw, H. G. G. Whitton

This paper describes the use of the electric-arc furnace for the production of tough-pitch, horizontal cast copper shapes and the production of copper anodes from tank house anode scrap. This installation is the only one of its kind in the United States. SINCE the initial use of electric-arc furnaces for refined copper melting on a commercial scale at Copper Cliff in 1936, this type of melting has been of extreme interest to everyone in any way connected with copper casting and fabricating. Early in 1948, Kennecott Copper Corp. decided to build an electrolytic copper refinery at Garfield, Utah. One of the major decisions to be made at that time was the type of furnace to be used for melting cathodes for casting into refined copper shapes and for melting anode scrap for the production of anodes. Based on the results obtained from arc furnaces by the Tnternational Nickel Co. of Canada, at Copper Cliff, and by the American Smelting and Refining Co., at Baltimore, coupled with certain important economic factors such as having an adequate amount of relatively cheap power available at the Magna Central Power Plant, high cost of poles and oil in the Salt Lake District, and the lack of natural gas at that time, the final decision was to install electric-arc furnaces rather than the standard type of rever-beratory furnaces. Experience has shown certain parts of the original installation to have been inadequate or in need of modification. Although the present status of arc-furnace melting at the Utah Refinery is far from perfect, nevertheless substantial progress has been made. At the Utah refinery, copper is melted in three 15-ft diam, size "M" Lectromelt furnaces, two of which are used for melting cathodes and one for remelting anode scrap. Each furnace is energized from a 13,800-225 v, 3-phase, 60-cycle, 6000-kva (at 40°C rise) oil-immersed water-cooled transformer. Auxiliary equipment for each refined copper furnace includes a charging machine, launders, ladle, 40 ft diam Walker-type casting wheel, bosh, and inspection conveyor. The anode furnace differs in that it is charged by hand from an elevated platform and the anodes are picked off the 24-ft diam casting wheel by a takeoff hoist and loaded directly into specially designed trailers, Figs. 1 and 2. Electrical Equipment Electric power to operate the arc furnaces is generated at the Kennecott-owned Magna Central Power Station two miles distant and transmitted to the Refinery outdoor substation at 44,000 v. At this point it is stepped down to 13,800 v and carried through concrete-lined underground tunnels to the switchgear and then to the primary side of the furnace transformers. The power is conducted from the Y-connected secondary bus bars of the transformer to the electrode arms by means of 22 flexible copper cable conductors per phase. Each cable has a cross-sectional area of 1,750,000 circular mils, giving a total area of 38,500,000 circular mils per phase. The power is carried from these cables to the three individual electrode holders by means of water-cooled copper bus tubing. The electrode clamps are incorporated in the electrode holders and are released by air pressure working against a spring in the clamp control cylinder. The movement of the electrode arms is either automatic or manual. The automatic control is used during melting and is regulated by three Westing-

Jan 1, 1954

By S. K. Asunmaa, W. D. English, N. A. Tiner, W. A. Cannon

This paper discusses the reaction of metal surfaces with fluorine. Fluorination reactions result in the formation of metal fluoride films which are "passive" toward further reaction of the metal with fluorine. These films are very adherent, and do not easily detach from the substrate metal by mechanical flexing or thermal shock. Exposure of passive films to a humid atmosphere produces hydrated metal fluorides which cause secondary fluorination reactions upon reexpo-sure of the metal surface to fluorine. The surface films formed range from 10 to 30A in thickness and they pow at the expense of surface oxide films. The apparent film formation is completed rapidly in 15 to 30 min on stainless steel and nickel surfaces. On copper and on Monel surfaces, the film at first grows rapidly, then increases slowly over an extended period of time. Passive films are formed at all fluorine pressures in the range from 0.1 to 1.4 atm at room temperature. ALL metals react when exposed to fluorine. These reactions generally produce surface films which consist of metal fluorides. The rate of reaction is largely determined by the extent to which these films are protective. Although there is an extensive literature concerning reactions of oxygen with metals, there are very few investigations reported concerning fluorine-metal reactions. Brown, Crabtree, and ~uncan&apos; investigated the kinetics of the reaction of gaseous fluorine with copper metal which had been freshly reduced in hydrogen. The reaction rate was independent of pressure over the range from 6 to 60 torr. A logarithmic rate law was obeyed in the temperature range from 25" to 300" ~. There was some deviation at higher temperatures which could have been the onset of a parabolic law. The calculated film thicknesses ranged from about two molecular layers, 10A, for 5 hr exposure at room temperature to thirty-five molecular layers for 5 hr exposure at 200" . The authors concluded that no single mechanism could explain all the observations. O7Donnell and spatkowski2 studied the reaction of fluorine with copper at 450°C at pressures from lo to 133 torr. The reaction was found to be pressure -dependent and followed a logarithmic rate law. It was not entirely diffusion-controlled, and fluorine was thought to be the migrating species in the reaction. Miscellaneous metal-fluorine reactions were investigated by Haendler et ~1.~ Reaction products were identified but no rate data were determined. Air Prod- ucts and Chemicals, Inc., have conducted an investigation of reactions between fluorine and various metal powders at room temperature and 85° C. Fluoride film thickness as a function of time of exposure was reported on the assumption that the reaction takes place between fluorine and metal to form the normal metal fluoride. Surface areas of the powders were only estimated so the relative film thicknesses may not be exact. The data showed reaction rates which were generally logarithmic in character, the rate of film growth virtually ceasing after a few hours exposure time for some alloy powders. The effect of moisture on fluoride films was also investigated by measuring additional reaction with fluorine after exposure of passivated powders to atmosperic moisture. The fluorination of iron was studied by 0&apos;~onnell~ at temperatures from 225" to 525" ~ and at pressures ranging from 20 to 200 torr. In all ranges, the reaction followed a logarithmic rate law and was dependent on the square root of the gas pressure. The author concluded that fluorine gas passes through pores in the film. As the film grows, the blocking of pores leads to a rapid decrease in reaction rate; hence a logarithmic rate law is observed. Jarry, Fischer, and Gunther&apos; investigated the mechanism of the reaction of fluorine with nickel at about 600" to 700°C. On the basis of the metallographic examination of fluoride scales growing on the nickel and from separate radioautographic data, it was claimed that fluorine is the migrating species in the reaction. This is in sharp contrast to the growth of oxide films on nickel where it has been shown that nickel ions migrate through the scale to the gas-solid interface to react with oxygen. Few investigations have been reported of the reaction of fluorine with metal oxides. Such investigations should be of great significance for a better understanding of passivation in view of the ubiquitous oxide films on technical alloys. Haendler et al.3 studied the reaction of fluorine with oxides of copper, tin, titanium, zirconium, and vanadium. Copper (I) oxide reacted as follows in the temperature range 150" to 300"~: temperature above 300" ~ was required for the CuO to react to form additional copper fluoride. Ritter and smith7 also investigated the reaction of fluorine with copper (11) oxide. An oxide powder comprised of spherical particles with a fairly high surface area was reacted with fluorine, starting at room temperature and increasing to 100° C over a period of 3 or 4 hr. The initial reaction was slow until the fluoride film thickness reached about to or 15R at which time the reaction rate accelerated, then decreased again. Most of the kinetic data was obtained during this final phase of reaction. The authors conclude that the film grows slowly at first until the stresses developed in the distorted lattice are sufficient to rupture the initial

Jan 1, 1969

By R. C. Thompson

The lead-zinc mill of Phelps Dodge Corporation, Copper Queen Branch, Mines Division, Bisbee, Arizona, is about 3 miles from the main hoisting shafts of the Junction and Campbell mines at Lowell. All the ore treated in the mill is obtained from these two mines. The mill was designed for an all-flotation treatment of 450 tons of lead-zinc ore per day, and has been operated at that capacity since the start of milling operations on Nov. 17, 1945. An expansion program is underway whereby the mill capacity will be doubled, but this article describes only the original program and presents results of the 450-ton operation. General Description The milling plant consists of an ore-receiving bin and three steel-constructed buildings housing, respectively, the primary crushing equipment, the secondary crushing equipment, and the ore-storage bins, grinding, flotation, and filtering equipment. The mill site is the one that was used for a previous copper-concentrating plant, which was operated over a period of years and then dismantled. There remained from this operation some milling equipment, a reservoir for mill-water supply, railroad tracks, tailings-disposal ponds, and a steel-constructed building, all of which were incorporated in the design of the present lead-zinc mill. The location plan of the plant layout is shown in Fig I. The flowsheet of the mill is based on the conventional scheme for lead-zinc treatment, however, several innovations were made necessary in order to utilize the existing building. Placing of equipment also was governed by the design of the building; thus making the mill unique in many respects. The following brief description of the mill building as adapted to the flowsheet points out the compactness of the installation and some of its unusual features. The first floor (Fig 2) houses the grinding equipment, with connecting conveyors for ore feeding, also an air compressor, two vacuum pumps, bins for lead and zinc concentrate storage with individual conveying systems for loading the two kinds of concentrates. Filtering of concentrates is done on the second floor, the concentrates discharging directly into the concentrate-storage bins. On this floor are the lead and zinc filters, two diaphragm pumps, sample-filtering equipment, sample-preparation room and a change room for the mill employees. The flotation machines are on the third floor, at elevations allowing a gravity flow of the lead and zinc concentrates to the thickeners. The annex to the building contains a freight elevator and provides space for all reagent mixing and feeding, also storage of reagents and grinding balls. All the water used for milling purposes is pumped from the Junction mine and

Jan 1, 1949

By Frederick T. Williams

THE purpose of this paper is to discuss the relative merits of the large 31/8 in. machine and the small 21/4-in. tappett machine in driving development-headings ; and although the . data here presented were obtained from cross-cut headings alone, experience has shown that the results are equally true in drifting, raising and winning. Recently we drove two parallel cross-cuts through the same formation, using a 3k-in. machine at the breast of one cross-cut., and a 2k-in. machine of the same make at the breast of the other. The results of this work afforded an ideal comparison, since in both cases the headings were advanced through rock practically of the same hardness and breaking-properties ; the amount of sludging was equal, and there was no difference in the condition of the steel or the machines, in the air-pressure or in the experience of the operating-crews. Some operators in the Cripple Creek district contend that there is ground which cannot be handled with the small machine, the holes being too small to contain enough powder to pull the ground, etc. The results obtained in working the property of the Portland Gold Mining Co., however, show that the ground worked by them does not fall in this class. During a period of two years there have been driven, with the small machine, 4 miles and 308 ft. of development-headings, through a diversity of ground, including Pike&apos;s Peak granite (a coarsely porphyritic type of granite), highly indurated, andesitic or phonolytic breccia, true massive andesite, trachytic phonolyte, tuffas, and along dikes of decomposed basalt and hard phonolyte; in every instance a satisfactory record was made. The headings here described were driven through highly indurated, andesitic breccia, having a hardness of from 5.2 to 7.2

Mar 1, 1906

By R. W. Armstrong, P. C. Jindal

WE should like to point out that Hu and cline.1 in their study of the recrystallization of titanium, have obtained data which appear very important for accurately determining the dependence of hardness on grain size for this material. It has been proposed2,3 that the macrohardness. H. of a poly crystalline material should depend on its average grain diameter, l. in accordance with the relationship: H =H0 + kHl-1/2 [1] where Ho and kH are experimental constants. This relationship follows from the hardness dependence on yield stress or flow stress4 and. thence. the Hall-Petch stress-grain size relations.5&apos;6 Fig. 1 shows the Diamond Pyramid Hardness. Dph. values vs the reciprocal square root of the average diameter of the recrystallized grains, taken from the titanium data reported by Hu and Cline. The data in this figure give a linear relationship for the hardness over a wider range of grain diameters than anyone has previously measured. The data are not linear, for example. on an I-1 or l-1/3 scale. At the very large grain sizes the data are in reasonable agreement with measurements earlier reported by Holden, Ogden, and Jaffee.7 For the grain sizes smaller than 1 µ, which correspond in Fig. 1 to hardness values greater than 150, the material was reported as not being completely recrystallized and, therefore, these data appear less meaningful as far as the hardness dependence on grain size is concerned. However. it has been suggested by other investigators that deformed materials exhibit strengthening due to an effective grain size refinement even in the unrecrys-tallized condition.8-10 Also. Hu and Cline have shown that a change in texture occurs for titanium during the recrystallization process and. especially. following it. The influence of this texture change on the hardness-grain size relation would be expected to be less than that reflected in the unidirectional stress-strain behavior, even for an hcp material. because of the actual combined stress system which applies for the hardness test. For, at least, certain combined stresses, average values of the orientation factors should still occur in the stress-grain size analysis of a material exhibiting a preferred orientation.&apos; We previously suggested3 that the experimental constants. H0 and kH. from the Meyer hardness-grain size relation should be correlated with the Hall-Petch constants, uoy and ky.5,6 Our recent study" of the Hall-Petch relation and the hardness-grain size results which obtain for a number of polycrystalline materials shows that: The inequality [2] is explained by noting that the hardness should be correlated. perhaps, with the flow stress at some value of strain, as suggested by Dugdale,12 and. also, that the influence of strain on the Hall-Petch relation is to increase uo and not change k very much." Normally. Dph values and Brinell hardness values are nearly equivalent to each other and to the Meyer hardness number. For the case of titanium, then. the inequality [2] may be evaluated using the experimental values of ao = 8.0 kg per sq mm and ky = 1.3 kg per mm3/2 obtained from the experiment of Guard.6,13 Thus, (Ho/uo) = 12 and (kH/k3) = 1.3. This research has been supported at the University of Maryland through the Center of Materials Research by the Advanced Research Projects Agency of the U.S. Government.

Jan 1, 1969

By J. J. Brown

Wilkes-Barre Meeting, Julie, runs., THE ore-hearth was the earliest type of furnace used in smelting Mississippi Valley lead-ores, which are very pure, and low in silver-content. The first smelters made no attempts to recover lead from the smoke; and since about 15 per cent. of the lead -in the charge escaped in this manner, early practice with the hearth was decidedly wasteful. At most of the large smelting-plants blast-furnaces with auxiliary roasters were substituted for the hearths long ago. But, upon the introduction of the Lewis and Bartlett bag-process for collecting fume, the ore-hearth was used by companies engaged in the manufacture -of pigments, simply on account of the large percentage of fume made by it. In fact, the extraction of lead was kept down by the use of hot blast and other devices. During recent years, however, several smelting companies have realized that the preliminary roasting of galena for the blast-furnace is not economical, and have, therefore, replaced the roasting-furnace with a modification. of the old Scotch hearth, in which a large percentage of the lead in a charge is recovered directly as pig-lead, while the remainder passes partly into fume and partly into slag low enough in sulphur to be charged into the blast-furnace without further treatment. The results obtained have proved so satisfactory, both As to recovery and operating-expense, that one eminent metallurgist has predicted the universal use of the ore-hearth on non-argentiferous ores. The-ore-hearth, thus employed as an adjunct to a blast-furnace plant, is rather a desulphurizer than a smelting-furnace proper,-the chief object being to make a blue slag suitable for the cupola-furnace. Hence, no special care is taken to obtain from it a large lead-extraction. * Head of Department of Ore Dressing and Metallurgy, Oklahoma School of Mines and Metallurgy, Wilburton, Okla.

May 1, 1911

By Norman F. Schulz, Emert W. Lindroos, Strathmore R. B. Cooke

DURING the course of an investigation of the effects of various starch products on hematite and quartz in regard to their separation by flotation, it was found that whereas most starches flocculated suspensions of hematite in water, they did not flocculate similar suspensions of quartz. However, a derivative of whole corn starch containing approximately one tenth aminoethyl group (-—CH,CH2NH2) per glucose unit proved to be an exception. This aminoethyl starch was a very good flocculant for both hematite and quartz, and also possessed the property of depressing both minerals in cationic flotation tests. In view of the widespread use of starch as a flocculating agent of solids in tailing water, pulps, and for coal slimes, ore and various other purposes in sulphide and nonsulphide flotation, attention is called to the effective surface activity of aminoethyl starch in flocculating suspensions of the two minerals investigated. Test Materials The starch products employed included Globe Pearl starch No. 144 and fresh aminoethyl starch, both supplied by the Corn Products Refining Co. Dr. A. L. Elder" has kindly furnished a description The minerals used in the various tests are listed in Table I. Their specific surfaces were determined by the air permeability method, which gave results reproducible to within plus or minus 3 pct. Surface areas obtained by krypton adsorption were greater than the air permeability values by a factor of 2.0 for quartz and 62.4 for hematite. Starch Adsorption on Mineral Surfaces Starch adsorption data were obtained by agitating for 1 hr measured volumes of neutral starch solutions of known concentrations with weighed quantities of finely divided mineral of measured specific surface. The mineral then was separated from the pulp liquor by centrifugation and the residual starch content determined by chemical analysis. The analytical procedure consisted of oxidizing the starch with an excess of dichromate in acid medium at elevated temperature and titrating the excess dichromate by the ferrous ammonium sulphate—potassium permanganate method. Analytical results were reproducible to within less than 1 pct. Adsorption data obtained in unbuffered solutions near the neutral point are plotted in Fig. 1. The adsorption on either mineral was far greater for the aminoethyl starch than for the Pearl starch. Flocculation The degree of flocculation was determined for a given pulp by measuring the time required for the supernatant liquid to reach a certain degree of clarity. This was accomplished by passing a standard light beam through the pulp, contained in a glass settling tube, and measuring the time required after agitation ceased for the intensity of the transmitted beam to reach a predetermined value. Starch reagent was added to each pulp in small uniform increments, and the settling time was determined after each such addition. Increase in pulp liquor volume due to the added starch reagent was ignored in these tests. Pulps were maintained at or near neutrality. of the preparation of the aminoethyl starch: "Three hundred and sixty grams of powdered unmodified corn starch was slurried in 3 liters of water and stirred during gelatinization. Eighty-six grams of ethylenimine was added slowly during reflux which was continued for 4 hr. The yellow solution set to a gel upon cooling. This was broken up and neutralized with HC1. The thick paste was dried on hot rolls. Adsorbed polyethylenimine and salts were removed from the yellowish products by washing first with acidified aqueous &apos;60 per cent&apos; alcohol. The white product contained nitrogen corresponding to about one aminoethoxy group per ten glucose residues." Only laboratory samples of this starch derivative have been prepared. The starch reagents for use in flocculation, flotation, and adsorption tests were made up by dispersing the appropriate quantities of air-dry starch in cold water, adding boiling water, and heating for 30 min at 120°C under pressure. When used ip adsorption tests, the starch solutions first were cleared of insoluble matter by centrifugation.

Jan 1, 1953

By Strathmore R. B. Cooke, Emert W. Lindroos, Norman F. Schulz

DURING the course of an investigation of the effects of various starch products on hematite and quartz in regard to their separation by flotation, it was found that whereas most starches flocculated suspensions of hematite in water, they did not flocculate similar suspensions of quartz. However, a derivative of whole corn starch containing approximately one tenth aminoethyl group (-—CH,CH2NH2) per glucose unit proved to be an exception. This aminoethyl starch was a very good flocculant for both hematite and quartz, and also possessed the property of depressing both minerals in cationic flotation tests. In view of the widespread use of starch as a flocculating agent of solids in tailing water, pulps, and for coal slimes, ore and various other purposes in sulphide and nonsulphide flotation, attention is called to the effective surface activity of aminoethyl starch in flocculating suspensions of the two minerals investigated. Test Materials The starch products employed included Globe Pearl starch No. 144 and fresh aminoethyl starch, both supplied by the Corn Products Refining Co. Dr. A. L. Elder" has kindly furnished a description The minerals used in the various tests are listed in Table I. Their specific surfaces were determined by the air permeability method, which gave results reproducible to within plus or minus 3 pct. Surface areas obtained by krypton adsorption were greater than the air permeability values by a factor of 2.0 for quartz and 62.4 for hematite. Starch Adsorption on Mineral Surfaces Starch adsorption data were obtained by agitating for 1 hr measured volumes of neutral starch solutions of known concentrations with weighed quantities of finely divided mineral of measured specific surface. The mineral then was separated from the pulp liquor by centrifugation and the residual starch content determined by chemical analysis. The analytical procedure consisted of oxidizing the starch with an excess of dichromate in acid medium at elevated temperature and titrating the excess dichromate by the ferrous ammonium sulphate—potassium permanganate method. Analytical results were reproducible to within less than 1 pct. Adsorption data obtained in unbuffered solutions near the neutral point are plotted in Fig. 1. The adsorption on either mineral was far greater for the aminoethyl starch than for the Pearl starch. Flocculation The degree of flocculation was determined for a given pulp by measuring the time required for the supernatant liquid to reach a certain degree of clarity. This was accomplished by passing a standard light beam through the pulp, contained in a glass settling tube, and measuring the time required after agitation ceased for the intensity of the transmitted beam to reach a predetermined value. Starch reagent was added to each pulp in small uniform increments, and the settling time was determined after each such addition. Increase in pulp liquor volume due to the added starch reagent was ignored in these tests. Pulps were maintained at or near neutrality. of the preparation of the aminoethyl starch: "Three hundred and sixty grams of powdered unmodified corn starch was slurried in 3 liters of water and stirred during gelatinization. Eighty-six grams of ethylenimine was added slowly during reflux which was continued for 4 hr. The yellow solution set to a gel upon cooling. This was broken up and neutralized with HC1. The thick paste was dried on hot rolls. Adsorbed polyethylenimine and salts were removed from the yellowish products by washing first with acidified aqueous &apos;60 per cent&apos; alcohol. The white product contained nitrogen corresponding to about one aminoethoxy group per ten glucose residues." Only laboratory samples of this starch derivative have been prepared. The starch reagents for use in flocculation, flotation, and adsorption tests were made up by dispersing the appropriate quantities of air-dry starch in cold water, adding boiling water, and heating for 30 min at 120°C under pressure. When used ip adsorption tests, the starch solutions first were cleared of insoluble matter by centrifugation.

Jan 1, 1953

By O. C. Ralston, F. Fraas

VIRTUALLY all commercial use of electrostatic separation has employed separators depending on differences of conductance of the broken, solid mixtures treated by them. The two main types of conductance separators have been: (1) Those in which the separating field is as near a static field between two charged electrodes as it is possible to maintain in the face of the usual leakage that takes place between electrodes with some 5 to 50 kv tension between them and spacing of 1/2 to 3 in.; (2) those in which a convective discharge of corona or spray type, but not a spark discharge, takes place between the carrier electrode and a charged electrode facing it, which is of very restricted area, such as a row of needle points or a small diameter wire parallel to the face of the carrier electrode. The present paper deals with this latter type. The principle is usable in separators where the carrier electrode, usually grounded, has the shape of a roller, a conveyor belt, a vibrating table, a sloping chute, or a nearly vertical plate. The innovation studied by us has been the use of the convective field for charging material on the carrier electrode and succeeded by a field between the carrier electrode and an electrode made of a true dielectric which cannot take on a charge by conduction but is charged by being in the radius of the corona discharge. The acquired charge is of the same sign as that of the corona but is not dischargable by contact with a good conductor. However, high-tension charge tends to leak off because of the ionization of the ambient air. The field between this electrode and the carrier electrode is as near static as it is possible to obtain. There are some differences in behavior of this electrode and that of the gas tube electrode used by Sutton, as will be discussed below. Both electrodes cause increased adhesion of nonconductive particles to the carrier roll. The particles are pinned there because they are convectively charged on their outer surfaces facing the corona electrode. The electrodes also cause increased rate of release of conductive particles tending to be pinned by corona charging but conveying the charge to the grounded carrier roll almost as rapidly as it is received by the particles. The sign of the potential on the corona-emitting electrode makes little difference in the separation. An electrode usually emits negative corona somewhat more easily than it emits positive corona, as electrons are then the fundamental particles emitted. With a positive electrode the flow of electrons involved in positive corona discharge is onto the electrode from the ambient gas. Theory In the separator illustrated in fig. 1, the nonioniz-ing electrode is a rotating, nonconductive dielectric cylinder designated as B. The ions emitted by the corona electrode, or wire F, charge both the particles on the carrier electrode, or roll A, and the surface of the dielectric electrode B. Whereas the space between roll A and wire F contains ions, the space between electrode B and roll A is a pure static field free of ions. The dielectric electrode has been described by Bullock.1 However, the corona electrode, which Bullock uses for the purpose of charging only the dielectric electrode, is adapted here to also charge the particles on the carrier roll. In operation the ionic field from the corona electrode is balanced with the static field from the dielectric electrode. The ionic field charges the particle so that it adheres to the roll. The static field intensifies the discharge of the corona charge by interfacial conduction and permits the release of the particle. The ionic and static fields therefore have opposing effects.2 The values of both fields are adjusted so that the poor conductor will adhere and the good conductor will be released.

Jan 1, 1951